j6) Autocareenamel 3087

BERGER PRODUCT SPECIFICATIONS
AUTOCARE ENAMEL FINISH

Synthetic Automotive Finish
PRODUCT A solvent based synthetic enamel specially formulated for refinishing all types of automobiles,
DESCRIPTION industrial machinery and appliances.
DESIGN Designed for use as a refinishing gloss finishing coat for cars, vans, trucks, buses, tractors &
FEATURES other heavy equipment.
Good gloss and colour retention properties with overall durability.
Excellent coverage, flow and levelling properties.
Resistant to spillage of petrol and diesel fuels.
PHYSICAL Recommended Application Data Wet [µm] Dry [µm] m2/l

CHARACTERISTICS Theoretical Coverage 78 25 18
Volume solids 45% (based on ASTM D2697)
Dry Film Thickness Range 25 µm to 35 µm
Flash Point 25 °C
Finish Gloss
Colour Range Standard Colour Range
Standard Packing Size 5 litres
APPLICATION BRUSH OR ROLLER Recommended method of application.

METHOD
CONVENTIONAL AIR May be used. Dilution of the paint to 18-20 secs on Ford Cup B4
SPRAY at 30 °C with Solvalux 7-9 to ensure good application properties.
AIRLESS SPRAY May be used.
Tip size : 0.43 – 0.53 mm (17 – 21 thou)
Pressure : 110 –160 kg/cm2 (1600 – 2300 psi)
DRYING TIME
Substrate Touch Dry Hard Dry Overcoating Interval
Temperature Minimum Maximum
15 °C 30 minutes 8 hours 36 hours Indefinite
USEFUL THINNER : SOLVALUX 7-9 (Maximum 10% Addition)

INFORMATION CLEANER : SOLVALUX 7-9
STORAGE : Store in a cool dry shaded area.
SHELF LIFE AT 25 ºC : 12 months minimum when stored as prescribed in the MSDS.
AUTOCARE ENAMEL FINISH REVISION 04-2014

J6
BERGER PRODUCT SPECIFICATIONS
SURFACE The service life span and the service performance of AUTOCARE ENAMEL FINISH are directly
related to the degree of surface preparation.
PREPARATION
• The steel surface coated should be dry, sound and undamaged. It shall be free of surface
contaminants such as grease, oil, dust, salts and rust.
• Soluble salts must be removed by washing with fresh water. Dry brushing should be done
to remove dirt and dust. If oil or grease is present, clean using mild detergent or solvent
and rinse thoroughly.
• It there is evidence of rusting, the affected areas should be thoroughly sand down with
sandpaper or mechanical tools to ensure complete removal.
• Application Autocare Primer as a primer coat and build-coat prior to application of this
product is necessary.
To avoid condensation of moisture onto substrate prior to coating application, relative humidity
should not exceed 85% and substrate temperature should be more than 3°C above Dew Point.
SUITABLE Autocare Primer, RAD 10, Luxacryl 1000, Luxachlor 1000

UNDERCOATS
NOTES • The coating specifications given above are typical. For specific recommendations to suit
individual applications, please refer to your Berger Paints representative.
• Do not over apply this product beyond the recommended film thickness as this may result
in extended drying times beyond those quoted overleaf.
• This product is designed for spray application only. Other methods of applications, such as
brush or roller, may compromise the gloss of the product.
SAFETY Avoid contact with eyes and skin. Wear suitable protective clothing such as overalls, goggles,
dust mask and gloves. Use barrier cream.
PRECAUTION This product contains low flash point solvents, do not use in poorly ventilated areas especially in
confined tank interiors.
Ensure that there is adequate ventilation in the area where the product is being applied. Do not
breathe in vapour or spray mist.
This product is flammable. Keep away from sources of ignition. Do not smoke.
Take precautionary measures against static discharge.
In case of fire, blanket flames with foam, carbon dioxide or dry chemicals.
FIRST AID Eyes : In the event of accidental splashes, flush eyes with warm water immediately
and seek medical advice.
Skin : Wash skin thoroughly with soap and water or approved industrial cleaner.
Do Not Use solvents or thinners.
Inhalation : Remove to fresh air, loosen collar and keep patient rested.
Ingestion : In case of accidental ingestion, DO NOT INDUCE VOMITING. Obtain
immediate medical attention.
For further safety information, please refer to our Material Safety Data Sheet (MSDS)
DISCLAIMER The information provided on this data sheet is not intended to be complete and is provided as general advice
only. It is the responsibility of the user to ensure that the product is suitable for the purpose for which he
wishes to use it. As we have no control over the treatment of the product, the standard of surface
preparation of the substrate, or other factors affecting the use of this product, we are not responsible for its
performance nor would we accept any liability whatsoever or howsoever arising from the use of this product
unless specifically agreed to in writing by us. The information contained in this data sheet may be modified
by us from time to time, and without notice, in the light of our experience and continuous product
development.
AUTOCARE ENAMEL FINISH REVISION 04-2014

J6

j6) Autocareenamel 3087

Uploaded by

Copyright:

Available Formats

j6) Autocareenamel 3087

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

j6) Autocareenamel 3087

Uploaded by

Copyright:

Available Formats

BERGER PRODUCT SPECIFICATIONS

AUTOCARE ENAMEL FINISH

PHYSICAL Recommended Application Data Wet [µm] Dry [µm] m2/l

APPLICATION BRUSH OR ROLLER Recommended method of application.

USEFUL THINNER : SOLVALUX 7-9 (Maximum 10% Addition)

AUTOCARE ENAMEL FINISH REVISION 04-2014

SUITABLE Autocare Primer, RAD 10, Luxacryl 1000, Luxachlor 1000

AUTOCARE ENAMEL FINISH REVISION 04-2014

You might also like