Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 76 views

    Experiment No. 01: DR D Y Patil School of Engineering & Technology

    Uploaded by

    pradnya sadigale
    1) The aim of the experiment is to control the speed of a servo motor using analog voltage. 2) A servo motor operates using negative feedback to reduce errors between the actual position and desired position by sending an error signal to drive the motor. 3) The experiment will test controlling the speed of a servo motor by varying the input voltage and measuring the resulting motor speed, with the expected result being that motor speed is proportional to the input voltage.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Experiment No. 01: DR D Y Patil School of Engineering & Technology

    Uploaded by

    pradnya sadigale
    76 views4 pages
    1) The aim of the experiment is to control the speed of a servo motor using analog voltage. 2) A servo motor operates using negative feedback to reduce errors between the actual position and desired position by sending an error signal to drive the motor. 3) The experiment will test controlling the speed of a servo motor by varying the input voltage and measuring the resulting motor speed, with the expected result being that motor speed is proportional to the input voltage.

    Original Title

    ExpNo1.docx

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1) The aim of the experiment is to control the speed of a servo motor using analog voltage. 2) A servo motor operates using negative feedback to reduce errors between the actual position and desired position by sending an error signal to drive the motor. 3) The experiment will test controlling the speed of a servo motor by varying the input voltage and measuring the resulting motor speed, with the expected result being that motor speed is proportional to the input voltage.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    76 views4 pages

    Experiment No. 01: DR D Y Patil School of Engineering & Technology

    Uploaded by

    pradnya sadigale
    1) The aim of the experiment is to control the speed of a servo motor using analog voltage. 2) A servo motor operates using negative feedback to reduce errors between the actual position and desired position by sending an error signal to drive the motor. 3) The experiment will test controlling the speed of a servo motor by varying the input voltage and measuring the resulting motor speed, with the expected result being that motor speed is proportional to the input voltage.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    You are on page 1of 4

    Dr D Y Patil Educational Enterprises Charitable Trust’s

    Dr D Y Patil School of Engineering & Technology


    Dr D Y Patil Knowledge City, Charholi (Bk.), Via. Lohgaon, Pune – 412 105

    Experiment No. 01
    Aim:

    Control the speed of servo motor using analog voltage.

    Objectives:

    1. Study Servo motor mechanism.


    2. Study working of servo motor.
    3. Study speed control of servo motor

    Introduction:

    The servo is an automatic electromechanical device that uses error-sensing feedback to correct
    the performance of a mechanism. The term applies only to systems where the feedback or
    errorcorrection signals help control mechanical position or other parameters.
    A common type of servomotors provides position control. Servos are commonly electrical or
    partially electronic in nature, using an electric motor as the primary means of creating
    mechanical force. Other types of servos use hydraulics, pneumatics, or magnetic principles.
    Usually, servos operate on the principle of negative feedback, where the control input is
    compared to the actual position of the mechanical system as measured by some sort of transducer
    at the output. Any difference between the actual and wanted values (an "error signal") is
    amplified and used to drive the system in the direction necessary to reduce or eliminate the error.
    An entire science known as control theory has been developed on this type of system.

    The Closed-Loop Control System

    The difference or error signal may be thought of as producing effects which move forward, from

    the point of comparison to the resulting action. The comparison itself depends on a signal which

    is fed back from the output of the process to be compared with the reference or input signal. The

    forward flow and feedback of signals form a loop around which information flows, see Figure 3.

    Such a system is therefore called a closed-loop system.

    1
    Various names are given to the signals in different industrial or other contexts, but the meanings

    of words in any one of the columns below are much the same:

    Difference Output Input


    Error Actual value Reference value
    Deviation Measured value Set value
    Controlled quantity Set point
    Desired value
    Demanded value
    Where the system is electrical, the state will normally be represented by signals expressed in
    volts; in the strip that being rolled in a steel mill it might be, for the width, a signal representing
    ten inches per volt.
    The difference in the comparison will be called the error signal and the part of the system that
    carries out the comparison is the error channel.
    There is usually a power amplifying device to drive the Actuator (which in Figure 4 is the
    geared motor).
    It is usual for control engineers to describe their systems in a block diagram form. The block
    diagram below describes the type of system we shall be using in this experiment.
    Here there is a comparison by the error channel of the input and output, the error is then
    amplified to drive a motor and gearing in the forward path so that the speed or position of the
    output shaft can be modified.

    2
    The motor is a permanent magnet type and can be represented in idealized form as in Figure 5,
    where Ra is the armature resistance and T1, T2 are the actual motor terminals.
    If the motor is stationary and a voltage Va is applied, a current Ia flows which causes the motor
    to rotate. As the motor rotates a back emf Vb is generated. As the motor speeds up, the back emf
    increases and Ia falls. In an ideal (loss free) motor, the armature current falls to substantially zero
    and Vb approximately equals Va. Thus if Va is varied slowly in either polarity, the motor speed
    is proportional to Va, and a plot of motor speed against Va would have the form of Figure 6.

    Procedure:
    1.

    Observations:
    Sr. Voltage (Volts) Speed of Motor(RPM)
    No
    1 +10
    2 +9
    3 +7.5
    4 +5
    5 +2.5
    6 +1
    7 0

    3
    Result And Conclusion:-

    Speed of Servo motor is controlled by varying voltage.

    You might also like