17th Exam P2 PDF
17th Exam P2 PDF
Name : __________________
(To be written by the candidate)
General instructions:
o Please check that this question paper contains 8 printed pages
o Please check that this question paper contains 64 questions
o The question paper is divided into three sections
o All questions in all three sections are compulsory
o All parts of a question should be answered at one place
1. The large difference between GCV and NCV of gaseous fuels is due to their
_________________________ 1
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
a) Hot water b) Wet steam c) Saturated steam d) all of them are possible
7. Water flows at a rate of 30 m3/hr. at 15oC in a 150 mm bore pipe horizontally. What
is the velocity of water flow in the pipe?
a) Temperature b) Pressure
c) Enthalpy d) None of above
14. In a counter-flow heat exchanger, cold fluid enters at 30°C and leaves at 50°C,
whereas the hot fluid enters at 150°C and leaves at 130°C. The LMTD is
_________________________ 2
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
17. What is the most effective way to avoid ambient air infiltration into a
continuous reheating furnace?
22. Which of the following has the lowest stoichiometric oxygen demand (kg/kg of fuel)?
23. Which of the following is used for controlling pressure in a natural draft furnace?
a) Forced draft fan b)Induced draft fan c) Dampers d)Both (a) & (b)
_________________________ 3
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
30. Which of the following depends on physical properties of fluids as well as geometry
of the heat exchanger?
_________________________ 4
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
36. 1% of the fuel is saved in boiler fuel consumption, if the feed water temperature is
increased by
a) drop in the total dissolved solids in boiler water b) more steam generation
c) rise in the total dissolved solids in boiler water d) greater purity of feed water
41. The insulation used for temperatures more than 350oC
a) Polyurethane b) polystyrene
45.
In a turbine, the thermodynamic process taking place is
a) contraction b) expansion c) condensation d) all the above
_________________________ 5
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
46.
In an FBC boiler with low ash fusion coal, if the bed temperature exceeds 950°C,
the result is:
a) Low steam temperature b) clinker formation
c) Melting of lime stones d) Ash carry over
47. Electrical energy consumption for coal sizing will be maximum for
(p) Rice husk, (q) Diesel, (r) Grade-C Coal, (s) Hydrogen
50. Water logging of 2 m lift of condensate at trap discharge will result in back pressure
of ____
_________________________ 6
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
Ans
E. R x (hg – hf) 14 x (660-60)
Effy = --------------------------- = ----------------------- = 84%
GCV 10000
For 120 hrs of operation, Furnace Oil requirement = 714 x 120 = 85680 kg
Oil tank volume = 85680 / (0.950/(1/1000)) = 90.189 m3
OR
Furnace oil requirement = 10 / 14 = 0.714 TPH = 714 kg/hr = 714 / 0.95 = 751.57 ltr/hr
For 120 hrs of operation, oil requirement = 751.57 x 120 = 90189 ltr
Oil tank volume = 90189 / 1000 = 90.189 m3
In a process plant, 30 TPH of steam after pressure reduction with pressure reducing valve
S-2
to 20 kg/cm2 gets superheated. The temperature of steam is 280oC. The management
wants to install a de-superheater to convert superheated steam into saturated steam at 20
kg/cm2 for process use, and its saturation temperature is 210oC.
_________________________ 7
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
A steam pipe of 100mm diameter is insulated with mineral wool. As a part of energy saving
S-3
measure, the insulation is upgraded with efficient Calcium silicate insulation. Calculate the
percentage reduction in heat loss due to above measure with the following data,
Ans
Heat loss thru non-insulated pipe = [10 + (95 – 25) / 20] * (95 – 25) ]
= 945 kcal/hr-m2
Heat loss thru insulated pipe = [10 + (55 – 25) / 20] * (55 – 25) ]
= 345 kcal/hr-m2
= 63.5 %
_________________________ 8
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
a)
Ans
(b)
(a) Calculate the blow down rate for a boiler with an evaporation rate of 5 tons/hr, if
S-5
the maximum permissible TDS in boiler water is 3000 ppm and with 18 % make
up water addition. The feed water TDS is around 400 ppm.
(b) Briefly explain temporary hardness and permanent hardness in boiler water
List down any five good practices in Furnaces for energy efficiency
S-6
_________________________ 9
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
Ans
Heat to power Ratio = 32*((2835.8/4.18)-73)/(5*860) = 4.5
Energy Utilization Factor = ( 32* ((2835.8/4.18)-73) + 5*860))/(8.2*4800)
=68.7%
Two identical oil fired boilers of capacity 100 TPH are operated in a refinery. They have a
S-8
full load efficiency of 90%. The part load efficiencies at 70% and 40% load are 75% and
65% respectively. For meeting 140 TPH requirement of steam, which one of the case
would you prefer to run and estimate the % savings in the preferred case. The enthalpy of
steam generated is 550 Kcal/kg and feed water enters the boiler at 50°C in all the cases.
Calorific value of the fuel oil is 10,000 Kcal/hr.
Case-1:
Ans
Amount of Fuel energy required when both the boilers are run at 70% load i.e, at 70
TPH load
Enthalpy change = (550 – 50) = 500 Kcal/kg
_________________________ 10
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
= 7.5 %
_________________________ 11
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
A gaseous fuel has volumetric composition as CH4 – 70 % & C2H6 – 30%. The
L-1
Gross Calorific Value of CH4 & C2H6 is 45000 kJ/Nm3 & 70000 kJ/Nm3
respectively. Find out the Net Calorific Value of gaseous fuel in kJ/Nm3. (Latent
heat of water vapor – 2445 kJ/kg)
Ans CH4 + 2O2 = CO2 + 2H2O
Hence, 0.70 Nm3 of CH4 will generate 0.70 x 2 = 1.4 Nm3 of H2O
Hence, 0.3 Nm3 of C2H6 will generate 0.30 x 3 = 0.9 Nm3 of H2O
(We know that mass of 22.4 Nm3 of H2O = 18 kg i.e. mass of 1 kMol)
L-2 A Textile plant has an extensive steam distribution network and the steam condensate is not
being recovered. The plant management is planning to recover the condensate and
generate flash steam for use as low pressure process steam for fuel savings. The following
are the parameters about the system.
_________________________ 12
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
Calculate the Quantity of flash steam which can be recovered, and the annual fuel oil
savings on account of condensate recovery
Ans
a) Flash steam available % = S1- S2/(L2)
Where: S1 is the sensible heat of higher pressure condensate.
S2 is the sensible heat of the lower pressure condensate
L2 is the latent heat of flash steam (at lower pressure).
Quantity of flash steam recovered from condensate = 1000 x 0.102 = 102 kg/hr
Condensate available for recovery after flash steam = 1000 – 102 = 898 kg/hr
Given data:
Enthalpy of steam at 10kg/cm2 = 665 kCal/kg
Furnace Oil consumption = 600 liters/hr
Specific Gravity of furnace oil = 0.89
G.C.V. of furnace oil = 10,000 kCal/kg
_________________________ 13
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
FEED WATER
TEMPERATURE AT
o
BOILER INLET = 60 C
ANS
Oil Consumption = 600 x 0.89 = 534 kg/hr
1) Boiler Efficiency = 7000 (665 - 60) X 100/ 534 X 10000
= 79.3 %
2) Feed water temperature in condensate tank
_________________________ 14
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
Ans a)
Ref page no 47
b)
_________________________ 15
Bureau of Energy Efficiency
REGULAR Paper 2 – Set A
1. Visual testing,
2. Sound Testing
3. Temperature testing
Ref page no 95
d) The drain points help in removing water in pipes due to condensation of steam.
_________________________ 16
Bureau of Energy Efficiency