Ata 08 Weighing and Leveling
Ata 08 Weighing and Leveling
Ata 08 Weighing and Leveling
Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only
08.00 GENERAL Presentation
WEIGHING METHODS:
Three Weighing technics can be used:
- Weighing on jack,
- Weighing on wheels,
- Weighing on jack and wheels.
PRIOR TO WEIGHING:
- Defuel the tanks by suction and drained.
- During defueling, pitch and roll attitude must be at 0 degree.
- The remaining fuel quantity must be check in weight and balance manual (one table for each aircraft version).
MW08.00_.01.G1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 2
08.00 GENERAL Presentation
AIRCRAFT PREPARATION:
Place aircraft in a closed hangar.
Equip with one clinometer, at level of cargo compartment door between frame 14 and frame17, for measuring aircraft pitch attitude = 0.
The aircraft configuration must be as follows:
- Flaps retracted.
- Control surfaces and trim in neutral position.
- Spoilers retracted.
- All doors and exits closed.
- Blanking plates, protection and covers removed.
MW08.00_.01.G1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 3
08.00 GENERAL Presentation
- No object workstand in contact with aircraft.
Make out list of missing equipment:
- Hydraulic system is topped up.
- Engine oil replenishing has been accomplished.
- Replenish toilets with water and applicable materials.
- Top up with potable water system.
- Note tire characteristics.
Clean aircraft to remove all trace of grease, dirt or water.
MW08.00_.01.G1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 4
08.00 GENERAL Presentation
WEIGHING ON JACK:
Jacking and load cell point location must be as follows:
- 1 or 2 on the nose.
- 1 for each wing.
- 1 safety stay on tail cone.
Note : Load cell depend on ATR version.
The maximum permissible load on each point is given in Job Instruction Card (reference n° 08-12-00).
MW08.00_.01.G1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 5
08.00 GENERAL Presentation
WEIGHING ON WHEELS:
The mechanical scales must be located as follows:
- 1 on the nose.
- 2 for the main gears.
Note : Mechanical scales depend on ATR version.
The three scales must have pans large enough to contain the landing gear tires.
MW08.00_.01.G1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 6
08.00 GENERAL Presentation
MW08.00_.01.G1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 7
08.00 GENERAL Exercises
MW08.00_.02.E1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 8
08.00 GENERAL Exercises
MW08.00_.02.E1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 9
08.00 GENERAL Exercises
MW08.00_.02.E1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 10
08.00 GENERAL Exercises
MW08.00_.02.E1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 11
08.00 GENERAL Exercises
MW08.00_.02.E1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 12
08.00 GENERAL Exercises
MW08.00_.02.E1L1 Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only Page 13
Table of contents
Presentation .............................................................................................................................................................................................................................................................
2
Exercises ................................................................................................................................................................................................................................................................
8
Copyright © 2011-2012 - ATR Training Centre - All right reserved For Training Only