Ikarus C42 Pilot Operating Handbook

C42
Owners Manual
OHB/C42/001
Issue 14
C42 Owners Manual (Microlight)
Page 1
C42 Owners Manual

FLIGHT, OPERATION AND MAINTENANCE MANUAL
G-___________________
This Manual belongs to aircraft reg
Type IKARUS C42 FB
: _____________________
Serial No
: _____________________
Series Build Aircraft

Microlight Aircraft Types:
IKARUS C42 FB80, C42 FB100
Type Approval Data Sheet (TADS) No. BM 68

Manufacturer:
Red--Air UK
Hangar 6
Wolverhampton Halfpenny Green Airport
Bobbington
Stourbridge
West Midlands
DY7 5DY
Tel. +44 (0)1384 221600
Email: sales@red-air.co.uk
Web: www.red-air.co.uk
CAA Company Approval No DAI/9949/11
This handbook should be kept with the aircraft.

CONTENTS
Page

CONTENTS ............................................................................................................................................................................... 3
ISSUE AMENDMENTS ............................................................................................................................................................. 4
Preamble ................................................................................................................................................................................ 5
SECTION 1 - AIRFRAME AND ENGINE LIMITATIONS........................................................................................................ 6
SECTION 2 - OPERATIONAL LIMITATIONS ......................................................................................................................... 9
SECTION 3 - OPERATION OF THE POWERPLANT ........................................................................................................... 10
SECTION 4 - FLIGHT ............................................................................................................................................................. 11
SECTION 5 - MINIMUM REQUIRED EQUIPMENT: ........................................................................................................... 16
SECTION 6 - WEIGHT AND BALANCE .............................................................................................................................. 17
SECTION 7 - DATA PLACARDS .......................................................................................................................................... 19
SECTION 8 - CHECKLISTS .................................................................................................................................................... 24
SECTION 9 - FLIGHT PERFORMANCE ............................................................................................................................... 26
SECTION 10 - DESCRIPTION OF SYSTEMS........................................................................................................................ 27
SECTION 11 - INSPECTION AND MAINTENANCE .......................................................................................................... 33
SECTION 12 - WING RIGGING AND DE-RIGGING, FLYING WITH DOORS REMOVED.......................................... 36
SECTION 13 - SETTING (RIGGING) AND MISCELLANEOUS DATA .............................................................................. 40
Page 3
ISSUE AMENDMENTS
Issue No.
1
Change/Description
Derived from Draft 3, format was A5; 7.1, placards were
on dash.
Date
3/10/03
Format change only
30/10/03
Tyre pressure change
05/05/04
Warp Drive 3 blade prop 80hp Version
22/06/04
50 hour Inspection schedule

Change (Item 7 Stub Axle)
Format change from CTP
Significant changes to flight sections by Paul Bennett
C.T.P.
65 litre fuel tank option.
Company name change.
29/09/04
7
8
08/12/04
24/03/05
Flying with doors removed

& tyre pressure change
Neuform fixed pitch prop 100hp version.
Neuform fixed pitch prop 80hp version. Neuform
variable pitch prop 100hp version. Seat weight limit
increase. Weight and balance loading plan change.
Checklists and inspection schedules altered.
Disabled hand rudder controls and wheelchair
stowage.
16/09/05
24/11/10
13
B model information added (carburettor heat and

oil/water heat exchanger).
472.5kg weight data. Beringer brakes,
Kiev Prop, and BRS information.
Galaxy GRS information added.
14
Kiev Prop for Rotax 912UL 80hp added.
07/04/11
10
11
12
Signature
15/11/05
15/09/06
03/03/11
18/03/11
Page 4
IKARUS C-42 FLIGHT AND OPERATORS MANUAL

Preamble
A record of all amendments is to be found in the front of this manual.
The C42 aircraft is a Microlight, conforming to the definition within BCAR Section S, 1999. To operate the
aircraft the pilot must hold at least a minimum of a Microlight PPL. The aircraft is not to be flown unless it
is registered, carries registration markings in accordance with the CAA requirements, and has a valid
Permit to Fly. The aircraft is to be flown under daytime VFR conditions only.
All Group A (conventional light aircraft) rated pilots should be checked out by an approved instructor
prior to flying this aircraft as it possesses characteristics that are unique to Microlight type aircraft. These
characteristics include low inertia, susceptibility to turbulence and wind gradient and special engine
considerations.
If the Neuform Variable Pitch propeller is fitted then documents reference NAM/C42/001 and
NOM/C42/001 must be considered part of this Owners Manual.
If the disabled hand rudder controls are fitted then document reference DRC/C42FBUK/03 must be
considered part of this Owners Manual.
If the wheelchair stowage modification is fitted then document reference C42/030 must be considered
part of this Owners Manual.
If Beringer brakes are fitted then the Beringer Maintenance Manual must be considered part of this
Owners Manual.
If a Ballistic Recovery System is fitted then the Ballistic Recovery System Operation and Maintenance
manuals must be considered part of this Owners Manual.
The engine of this aircraft is not certified, and could fail at any time. For this
reason NEVER fly over congested areas or other areas on to which a safe
landing cannot be made in the event of an engine failure. On cross country
flights, ALWAYS keep an emergency landing field in sight.
Changes to the control system, structure, wings and engine are prohibited.
All operating difficulties and equipment failures should be reported to Performance Aviation Ltd.
Page 5
SECTION 1 - AIRFRAME AND ENGINE LIMITATIONS

Airspeeds - all speeds are Indicated Air Speeds (IAS).
VNE, Never Exceed Speed:
VA Max. manoeuvring speed,
VS0 Stall speed, full flaps:
VS1 Stall speed, flaps retracted:
VFE Max speed :
139 mph,
94 mph,
37 mph,
47 mph,
72 mph,
121 kt
82 kt
32 kt
41 kt
63 kt
VNE & VA limitations are affected when flying with doors removed Aerosport MOD C42/019
VNE (Velocity Never Exceed): 103 mph, 90 kt.
VA (Maximum Speed for Full Deflection of Controls / Rough Air): 80 mph, 70 kt.
Weights:
Empty weight (max):
265.5 kg 100 hp 912S

268 kg 80hp 912
450 kg.
Max gross weight:
With 472.5kg MTOW Performance Aviation MOD C42PAUK/001 and Ballistic Recovery System
Performance Aviation MOD C42PAUK/003 or C42PAUK/006:
Empty weight (max):
Max gross weight:
288 kg 100 hp 912S

290.5 kg 80hp 912
472.5 kg.
Wing area
135 sq ft, 12.5 sq.m
Areas:
Structural limitations:
Positive limit load
Negative limit load
4g (at all speeds)

-2g
Centre of gravity limits: (Zero datum at the wing leading edge root)
Forward centre of gravity
Rearward centre of gravity
350 mm aft of datum (366mm at M>450kg).

560 mm aft of datum.
Airspeed markings:
White Arc:
Green Arc:
Yellow Arc:
Red Line:
Yellow Triangle:
37 to 72 mph (32 to 63 kt) full flap operating range.

47 to 94 mph (41 to 82 kt) normal operating range.
94 to 139 mph (82 to 121 kt) CAUTION, DO NOT USE IN TURBULENCE.
139 mph (121 kt) VNE VELOCITY NEVER EXCEED.
60 mph, 52 kt - Recommended Minimum Approach Speed
Control Deflection Limits

At VNE control surfaces should not be deflected more than one third full range.
VA is the maximum speed permitted in turbulent conditions. Full deflection of the

controls at speeds above VA is prohibited.
Page 6
Engine Limitations:
Max. Engine RPM.
5800 rpm (5 minutes max)

5500 rpm max continuous (80 HP)
5300 rpm max continuous (100 HP)
RPM Meter Markings: yellow 5500-5800 rpm (80 HP)

5300-5800 rpm (100HP)
red
5800 rpm
Propellers:
80hp: Warp Drive 2-blade 68 (1,72 m )
Pitch 25 at R = 400 mm from hub edge (blade root point of entry)
Full throttle ground static RPM 5000 rpm (prop = 2203 rpm)
Warp Drive 3-blade 68 (1,72 m )
Pitch 21 at R = 400mm from hub edge (blade root point of entry)
Ecoprop 170R 110/3, 3 blade
170cm x 20 @ 75% radius.
Neuform CR3 3 blade (1,75 m )
Pitch 23 @ 310mm from hub edge
Kiev Prop 263/1800 3 blade (1.70m )
Pitch 24 @ 350mm radius
100hp: Warp Drive 3-Blade 68 (1,72 m )
Pitch 2526 at R = 400 mm from hub edge (blade root point of entry)
Ecoprop 170R 130/3, 3 blade
170 cm, pitch 22 at 75% radius.
Full throttle static rpm, max. 5000 rpm (prop = 2057 rpm)
GSC Tech-III 3 blade
68 x 25@400mm from hub edge.
Full throttle static rpm, max. 5000 rpm (prop = 2057 rpm)
Pitch 27 @ 310mm from hub edge
Neuform CR3-V-R2H 3 blade variable pitch prop (1,80 m )
Pitch 24-31 @ 310mm from hub edge
Propeller pitch control lever position fully fine *
Kiev Prop 283/1800 3 blade (1.80m )
Pitch 24 @ 485mm radius
* Please note the Neuform Variable pitch propeller has specific maintenance schedules detailed in
Neuform Variable Pitch Propeller Operating Manual NOM/C42/001.
Page 7
Slight adjustment to the pitch of each of the above propellers may be necessary to obtain the correct
ground static rpm. An optical tacho on the propeller is the preferred method of measuring the engine
speed.
Engine
According to ROTAX Manual:
Oil Pressure:
Oil Temperature:
min.
max.
preferred range
2 - 5 bar
50 C
140 C (80hp), 130 C (100 hp)
90 - 110 C
Maximum coolant temperature
115C
Maximum Cylinder Head Temp. (CHT)

912 (80hp)
150C
912S (100hp) 135C
Above CHT and coolant temperatures assume 50% glycol/water coolant mixture.
Ballistic Reserve Parachute Systems
Junkers Magnum Light Speed Softpack:
Maximum operating speed 162kt, 186mph, 300kph
Maximum operating weight 475kg
Galaxy GRS 5/472.5:
Maximum operating speed 136kt, 157mph, 251kph
Maximum operating weight 472.5kg
Occupant Warning - The parachute recovery system installation has been approved
by BMAA on the basis that, as far as is practicable to demonstrate, it will create no
hazard to the aeroplane, its occupant(s) or ground personnel whilst the system is not
deployed; and that when properly maintained, the risk of malfunction, deterioration or
inadvertent deployment is minimised. The BMAA has not approved the system itself or
considered the circumstances, if any, in which it might be deployed. The effectiveness
of the system for the safe recovery of the aeroplane has not been demonstrated.
Page 8
SECTION 2 - OPERATIONAL LIMITATIONS

This aircraft
-
must not be flown in aerobatic manoeuvres.
must not be flown at bank angles beyond 60 degrees.
must be flown under daylight, VFR conditions only.
must not be flown in known airframe icing conditions.
must not be flown in conditions of moderate turbulence or above, or in winds exceeding 22 kts,
at surface level, less if gusty.
Always follow the appropriate regulations for this category of aircraft.

Permitted Manoeuvres
Non-aerobatic operation only.
Any manoeuvre necessary for normal flight.
Stalls.
Steep turns with bank angles not exceeding 60
Placarded limitation must be observed at all times. Additionally pilots should only fly in conditions which
are compatible with their own ability.
Maximum permitted dry empty weight:
100 hp 912S
80 hp 912
265.5 kg
268 kg
With 472.5kg MTOW Performance Aviation MOD C42PAUK/001 and Ballistic Recovery System
Maximum permitted dry empty weight:
100 hp 912S
80hp 912
288 kg
290.5 kg
Page 9
SECTION 3 - OPERATION OF THE POWERPLANT

Description:
The Rotax 912 and 912S are 4 cylinder, four stroke, horizontally opposed engines. They are cooled by a
combination of air-cooled cylinders and liquid cooled heads. The engine oil is also air-cooled with a
small radiator.
The B Model aircraft utilise an oil/water heat exchanger in place of the oil radiator. A carburettor heat
control is also fitted which draws air from around the exhaust, via the usual air filter. This should only be
activated if carburettor icing is suspected (see Emergency Procedures sction).
Fuel Type: Min 91 Octane for the 80 hp, Min. 95 Octane for the 100 hp engine (RM/2 method)
automotive gasoline leaded or unleaded or AVGAS 100 LL . Prolonged use of AVGAS can cause
damage to the Rotax 912, precludes use of fully synthetic oil and requires more frequent oil and oil filter
changes. Please study the Rotax engine operating manual.
CAUTION: Never handle the propeller with the ignition on.

To Start:
Main fuel valve,

Master switch
Electric fuel pump
Throttle at idle
Brakes
Mags (both)
Propeller area
Rear of aircraft
Choke (pulled out)
After engine starts, choke
Check:
OPEN
ON
ON
FULL AFT
ON
ON
CLEAR
CLEAR
ON Start
OFF
OIL PRESSURE RISING.
Note: If the engine doesnt start, repeat the procedure. If the engine floods, close the main fuel valve,
half open the throttle and turn over the engine. When it starts, reduce the throttle quickly to idle (2000
rpm) and turn on the fuel.
Open the main fuel valve - dont forget!

Note: A water-cooled four stroke engine requires a fairly long warm up period. Run the engine at 2000
rpm for 2 minutes minimum then at 2500 rpm until the oil temperature is at least 120F (50 C). Perform
an ignition system check at 3500 rpm by turning off each ignition switch in turn. The engine speed drop
should not exceed 300 rpm with a maximum difference of 120 rpm.
Failure to let the oil temperature reach 50C can result in

carburettor ice forming during takeoff. It is imperative
that this procedure is followed otherwise serious injury or
death may result.
Page 10
SECTION 4 - FLIGHT
4.01
Taxiing:
The nose wheel steering is conventional and is directly connected to the rudder pedals. Push the
right pedal to turn right. Push the left pedal to turn left. Taxiing is simple; the turning radius of the
C42 is small, and the aircraft handles cross winds during taxiing very well.
When taxiing with a strong tail wind, hold the control stick firmly in the neutral position.
When taking off or landing on bumpy grass strips, exercise caution to avoid striking the propeller.
This may require performing soft field take-off and landing procedures.
Note: with a fully aft cg it is possible for the aircraft to tip back and sit on its tail skid, particularly if
taxiing over uneven ground.
4.02
Takeoff and climb:

Complete the pre-take checklist VITAL ACTIONS. Ensure the trim is set to one step above
neutral, as indicated by a centre-scale reading on the trim indicator and the flaps are set as
required (Max 1 stage, 15 degrees). Always take off into the wind when possible. The maximum
demonstrated 90 degree crosswind component is 17 mph (15 knots).
The stick position should be positively aft of neutral and maintained during the ground roll to
minimise the loading on the nose wheel. Smoothly bring the throttle to the full forward position,
check the tachometer for full throttle rpm.
It will be necessary to hold right rudder to counteract slipstream effect and engine torque during
the ground roll and climb out. The nose wheel lifts off at approximately 30 mph, (26 kt).
Accelerate with the nose wheel off the ground 2-4 inches, (5-10 cm). The aircraft will take off at
44 mph (38 kt).
After takeoff, let the aircraft accelerate to the best rate of climb speed Vy 70 mph, (60 kt), 1
stage flap extended. At between 150 and 200 ft raise the flaps to the cruising flight position (0
degrees or no flaps). Be ready for the pitch trim change to nose-down. Trim the aircraft as
required for the climb. Recommended full power climb 80 hp 62 - 66 kts. Recommended full
power climb 100 hp 66 - 70 kts.)
Best angle of climb speed Vx is 55 mph, (48 kt) ( 1 stage flaps ). However this climb speed and
angle are not recommended because in the event of an engine failure it is possible that control
of the aircraft may be lost. The aforementioned procedure is therefore recommended. This
should ensure full control is maintained in the event of an engine failure shortly after takeoff
providing immediate engine failure action is taken.
Cross wind take off :
Take off should be made as described above but with into wind aileron. Maintain track down
the centreline with rudder and further maintain into wind aileron as required to stop your drift
during the take off roll and rotation. (Out of wind wing main wheel can lift off first during take off
). Resume wings level balanced flight after take off.
The maximum demonstrated 90 degree cross wind component is 17 mph (15 kts)
4.03
Cruising flight:
Note: Typical economic cruise speeds lie in the range 80 to 105 mph (70 to 90 kt); 109 mph (95
kt) with the 100 hp engine.
Maximum continuous engine speed is 5500 rpm for the 80 hp 912, and 5300 rpm for the 100 hp
912S.
Page 11
Variations in rpm and cruise performance occur with different loads.

Typical cruising flight (80 hp)
Engine speed:
Airspeed:
Fuel flow:
4500 rpm.
95 mph (83 kt)
2.8 Imp. gallons per hour, (12.7 l/h)
The maximum speed in cruising flight is 118 mph (103 kt).

Note:
This maximum speed applies only in smooth conditions with no turbulence. In

turbulent air, speed must be kept below VA = 94 mph (82 kt).
4.04
Turning flight:
In turning flight, it is necessary to co-ordinate the use of the ailerons and the rudder. At normal
cruising speeds 80 mph (70 kts) to 103 mph (90 kts) initiate the turn with aileron maintaining
balance as necessary with rudder. At bank angles exceeding 45 degrees the pitch trim force
required to maintain level flight increases noticeably. Banks exceeding 60 degrees are
prohibited. In steep bank turns remember to maintain the attitude at entry and maintain
airspeed with power. Failure to maintain correct attitude can result in a spiral dive developing. At
60 degrees of bank the stall speed is multiplied by a factor of 1.41 and you will be pulling 2g.
4.05
Slow flight, stalling and use of flaps:

In cruising flight configuration with the landing flaps retracted and at speeds below 60 mph (52
kt) the top of the engine cowl will be well above the horizon. Control inputs of the aileron and
rudder will be severely dampened and the overall response of the aircraft markedly reduced.
Only gentle turns should be made of up to 20 degrees of bank ensuring the aircraft remains in
balance. In slow flight if a wing drops, centrally reduce back pressure on the stick and lower the
nose. Prevent further yaw with the rudder and do not attempt to lift the wing by aileron input.
At approximately 48 mph (42 kt) there will be a slight buffeting of the airframe. The aircraft is still
controllable. However, aileron input should not be used and the stick kept central with any
tendency for the wing to drop use opposite rudder to prevent yaw.
If stalls are entered very gently the aircraft can enter a controlled mushing descent, control can
still be maintained with rudder. (It is important not to over use rudder and potentially put the
aircraft into a reverse spin entry).
When the aircraft stalls the nose will drop. By removing back pressure the aircraft should recover.
Typical height loss in the wings-level stall is approximately 100 ft., and max. Pitch attitude change
25 below the horizon. In turning flight stalls the typical height loss is 120 ft. At full flap (40
degrees) the pre-stall buffet, 39 mph (34 kts), is markedly more noticeable and there is an
increased tendency for the wing to drop if balanced flight is not maintained.
Speeds are as follows:
VS1 flaps retracted (0) 47 mph, (41 kts)
VS2 first notch of flaps (15) 42 mph, (36 kts)
VS0 full flaps ( 40) 37 mph, (32 kts)
The above specified stall speeds will vary slightly depending on the all up weight.
Spinning
Page 12
Spin recovery Immediately fully close the throttle. If full flap is set raise the flaps otherwise leave.
Apply rudder opposite to the direction of rotation until rudder is centralised and then release
back pressure from the stick. If the spin continues apply full opposite rudder then move the stick
forward until the spin stops.
Avoid over speeding the aircraft during the pull out.
4.06
Descents, landing and roll out:

Entering a conventional circuit in the cruise 92 mph (80 kts) when on the base leg reduce power,
maintaining attitude allowing a reduction in airspeed to 72 mph (63 kts) (white arc) select 15
degrees flap (1 stage) simultaneously lowering the nose to maintain 67 mph (58 kts) and trim.
On final approach if the crosswind component is less than 12 mph (10 kts) you can select full
flaps simultaneously lowering the nose to maintain 55 kts. Continue your approach at 63 mph (55
kts) and trim if required. Minimum approach speed in this configuration is 60 mph (52 kts).
In calm conditions it is acceptable to use side slip technique to increase your rate and angle of
descent, but it is recommended the aircraft is returned to a standard approach configuration
before reaching 100 ft above the runway.
In the landing phase during the hold off when the main wheels touch ensure that the nose
wheel is maintained clear of the runway during the landing roll bringing the stick steadily
rearward until it reaches the backstop and allow the nose wheel will settle onto the runway as
the speed decays.
Caution should be exercised when applying brakes as it is possible to lock the main wheels
under certain conditions. It is preferable to allow the aircraft to de-accelerate to a walking pace
before applying any braking action.
Cross wind landing technique
Establish the aircraft on a powered approach, tracking the centreline and allowing for drift. For
crosswind components of 12 mph (10 knots) or above only 1 stage of flap (15 degrees ) is
recommended. Approach speed should be 66 mph (58 kts).
The generic wing down approach is recommended. If you are not fully aware of crosswind
techniques you should consult an approved instructor. The following description is for guidance
and not a substitute for proper instruction.
Below 200 feet on the approach, apply rudder to align the nose of the aircraft with the
centreline of the runway simultaneously lowering the into-wind wing with aileron to maintain your
track down the centreline (preventing drift).
Smoothly allow the aircraft to settle on to the runway, the into wind wheel will contact the
runway first maintaining directional control with the rudder and progressively increase the intowind aileron deflection as the airspeed reduces.
Allow the nose wheel to settle on to the ground earlier than normal to transfer steering authority.
Avoid fully holding off before touchdown as drift angle increases and airspeed decays, the
control authority also reduces.
Page 13
4.07
Shutting down the engine:

During the descent and subsequent taxiing, the engine will have cooled down enough to permit
immediate shut-down after parking.
Turn off all electrical accessories and radios before shutting down the engine.
4.08
Sudden loss of engine power:

Set attitude for best glide at 58 kts and trim (This is a good compromise speed and easy to
achieve quickly). Assess the wind direction and select a suitable landing area into wind. Plan
your approach and execute this action.
If you have time check the reason for engine failure:
Master switch ON
Magneto switches ON
Fuel tap ON
Choke OFF
Try restart:
Auxiliary fuel pump ON
Throttle set 1/4 open
Press starter
If restart not achieved and you still have sufficient height and time make a MAY DAY call. Stay
on the frequency you are already on if contact established. Remember it is more important to
keep flying the aircraft on your planned approach than any other action.
Do not turn your back on the planned landing site or make a 360 degree. A constant aspect
approach is recommended coupled with beats and turns and or sideslip to increase rate of
descent.
IMPORTANT: SHUT DOWN CHECKS (Prior to landing)
Throttle closed
Master OFF magnetos OFF
Fuel OFF
Security - harnesses tight, reassure passenger
1 Stage of flap can be applied at any time during your descent.
During your initial approach you should be aiming at the middle off the landing site bringing your
aiming point back to one third in after applying full flap. All emergency landings should be made
into wind with full flap to minimise landing speed.
Remember - KEEP FLYING THE AIRCRAFT AT ALL TIMES.
Page 14
4.09
Emergency procedures:
I
Should you lose elevator control due to a mechanical failure, trim the aircraft to 65 mph
(56 kt). With a reduced power setting, make a shallow power-on landing approach,
throttle back and flare using the trim. Avoid use of the flaps.
II
If you lose aileron control, you can fly the aircraft with rudder alone.
III
If you lose rudder control, the aircraft can be flown with the ailerons alone.
IV
In the event of carburettor or engine fire:

Main fuel valve off .
Electric fuel pump off.
Full throttle, (to burn the remaining fuel fast).
Maximum permissible airspeed to put out the flames.
Call MAYDAY
Follow emergency landing procedures.
B Model only: if carburettor icing is suspected, with symptoms such as rough running,
activate the carburettor heat control. An rpm drop of around 100-150rpm is expected, with
a small reduction in power. If rpm increases within 1-2 minutes carburettor icing was likely to
have been occuring and the carburettor heat control should be left on for the remainder of
the flight. Use of the carburettor heat control at other times is not recommended.
VI
Ballistic Recovery Parachute equipped aircraft only: if the pilot-in-command decides to

deploy the parachute in an emergency situation he should do so without delay, before
height is lost or speed becomes excessive.
As the operation of these systems is not guaranteed, and system failure may place the
aircraft in a more dangerous situation than the initial problem, consideration should be
given before flight to the situations in which you personally, as the pilot-in-command, would
make the descision to deploy the parachute.
Such occurances may include mid-air collision, structural failure, pilot incapacity, or engine
failure over terrain unsuitable for forced landing (note the latter is preventable by sensible
piloting).
Note that if a forced landing has a reasonable chance of being accomplished safely it is
the generally accepted course of action.
To deploy the parachute:
Switch off engine
Pull handle firmly (extension about 25 mm on Junkers, up to 100mm on GRS)
If time available, retighten seat belts
Protect face and body with your arms
Press into seat by extending your legs
Refer to Operators Manual supplied with system and appended to this Owners Handbook
for details.
Page 15
SECTION 5 - MINIMUM REQUIRED EQUIPMENT:

a.
b.
c.
d.
e.
f.
g.
h.
i
Four point harness.

Airspeed indicator 0-150 mph (0 - 130kt)
Altimeter.
Data placard and weight and balance document.
Pre flight check list.
Tachometer
Cylinder head temp. or coolant temperature gauge.
Oil pressure gauge
Oil temperature gauge
Page 16
SECTION 6 - WEIGHT AND BALANCE

6.1
Weight and Balance Calculations
The centre of gravity is measured in mm behind the zero datum. Zero datum is the leading edge root.
The aircrafts empty weight and cg are derived first: Place the aircraft in a level position on three scales,
such that the stabilizer is horizontal, as shown below. Push down on the rear fuselage, just in front of the
tail, and chock the nose wheel to level the aircraft. Record the reading of each scale.
G1
G2 = GL + GR
x
a
b
Calculate the position of the empty cg, from the formula:
X=a
G1 b
= ................mm
G1 + G 2
(a and b are values to be measured for the specific aircraft).

Insert the values for total empty weight, (G1 + G2) and cg distance aft of datum, (X), into the table
below. Multiply Empty Weight (kg) by cg distance aft of datum (mm) to derive empty weight moment
(kg.mm) in the last column.
Complete the remaining weights for seat loads, fuel and baggage and multiply these by the lever arm
lengths (given below).
Add up the weights and moments, then divide the total weight by the total moment to give laden cg
location aft of datum.
Ensure that this cg location lies within the limits 350 to 560 aft of datum.
For operation at weights over 450kg, the forward limit is 366mm aft of datum. This is a limitation to remain
within tested nose wheel loads.
Page 17
Loading plan
Position
weight
kg
lever arm
mm
moment
kg.mm
Empty weight
1. Seats
400
2. U nder seat bags
400
3. Fuel
950
4. Samsonite case
950
T otal W eight
kg T otal Moment
T otal Moment
centre of gravity C G =
6.2
kg.mm
kg.mm
------------------------------------------ =
T otal W eight
kg
mm
Conditions of Weighing
The dry empty weight of the aircraft is defined under the following conditions:
All normal installed equipment fitted.
Oil and coolant levels normal.
No usable fuel.
Note: Remaining within the maximum Take-off Weight (MTOW) of 450 kg (or 472.5kg with
appropriate modifications fitted) is the pilots responsibility.
Page 18
SECTION 7 - DATA PLACARDS

The following placards are fitted to the aircraft, in the locations indicated:
7.1
In View of the Pilot:

For the 100hp:
For the 80hp:
VNE
VFE
139 mph (121 kt)

72 mph (63 kt)
RPM max. (5 mins)

RPM max. continuous
Oil pressure
Oil Temp.
Oil Temp.
CHT
5800 rpm
5300 rpm
2 5 bar
Min. 50C
Max. 130C
Max. 135C
VNE
VFE
139 mph (121 kt)

72 mph (63 kt)
RPM max. (5 mins)

RPM max. continuous
Oil pressure
Oil Temp.
Oil Temp.
CHT
5800 rpm
5500 rpm
2 5 bar
Min. 50C
Max. 140C
Max. 150C
Flying Without Doors:

Aerosport MOD C42/019
Flying Without Doors
Aerosport MOD
C42/019
VNE 103 mph (90 kt)
VA 80 mph (70 kt)
Neuform Variable Pitch Prop:

Propeller Pitch Control
Lever Forward Fine
Lever Aft - Coarse
Page 19
7.2
Secondary Control Markings
The following secondary controls are marked for function and operation:
Trim - next to the trim rocker switch.
NOSE DOWN
TRIM
NOSE UP
Flaps - next to the flaps control lever:

FLAPS
UP
DOWN
Fuel Tap- next to the fuel tap:
FUEL
ON
OFF
Starter - next to the starter button
Choke - next to the choke:
STARTER
(switch)
CHOKE
Carburettor Heat - next to the carburettor heat knob (B model only):

CARBURETTOR HEAT
Page 20
7.3
Fuel Filler - next to the fuel filler:
For the 100 hp Rotax:

Unleaded MOGAS
Minimum Fuel Grade
MON 85, RON 95, AKI 91
AVGAS 100LL
Avoid prolonged use of Avgas
For the 80 hp Rotax:
Unleaded MOGAS
Minimum Fuel Grade
MON 83, RON 91, AKI 87
AVGAS 100LL
Avoid prolonged use of Avgas
7.4
Oil Filler - near the oil filler:

Use synthetic or semi-synthetic oil.
Specification API SG, SF or higher.
See Rotax manual for oil
recommendations
7.5
Fuel Tank near the fuel filler ( 50, 65 or 100 litre option )
Usable fuel capacity 50 litres
7.6
Loading: Within pilots view

Empty weight
Date of Weighing
Max. weight
Max cockpit load
Min. cockpit load
Max weight per seat
Max. permitted fuel at max. cockpit load
450 kg
172 kg
55 kg
120 kg
Max. permitted cockpit load with max. fuel
Page 21
Or with 472.5kg MTOW Performance Aviation MOD C42PAUK/001 and Ballistic Recovery System
Empty weight
Date of Weighing
Max. weight
Max cockpit load
Min. cockpit load
Max weight per seat
Max. permitted fuel at max. cockpit load
472.5 kg
172 kg
55 kg
120 kg
Max. permitted cockpit load with max. fuel
Wheelchair Stowage
Aerosport Mod C42/030
Max cockpit load
reduced to 160.5 kg
with wheelchair fitted
7.7
Occupant Warning Within occupants view
This aircraft has not been certified to

an international requirement.
Aerobatics and spinning prohibited.
Flight by day and in VFR only.
Smoking prohibited.
7.8
Unleaded Fuel Warning Within pilots view

USE OF UNLEADED MOGAS
(See Airworthiness Notice 98B & C)
* Only legal in aircraft specifically approved for the
purpose.
* Fuel to be fresh, clean, alcohol and water free.
* Check for leaks and deterioration of pipes, fittings,
valves.
* Verify take-off power prior to committing to takeoff.
* Tank fuel temperature not above 20C.
* Fly below 6000 ft.
CARB ICING AND VAPOUR LOCK MORE LIKELY
Page 22
7.9
Ballistic Recovery System Warning Within pilots view
Occupant Warning
The parachute recovery system installation has been
approved by BMAA on the basis that, as far as is
practicable to demonstrate, it will create no hazard to the
aeroplane, its occupant(s) or ground personnel whilst the
system is not deployed; and that when properly maintained,
the risk of malfunction, deterioration or inadvertent
deployment is minimised. The BMAA has not approved the
system itself or considered the circumstances, if any, in
which it might be deployed. The effectiveness of the system
for the safe
recovery of the aeroplane has not been demonstrated.
Close to deployment handle:
WARNING EMERGENCY PARACHUTE
Pull Handle Firmly to Deploy
Unapproved Equipment - see Pilots Handbook
On exterior of aircraft, close to parachute breakthrough panel:

DANGER
and:
Ballistic Recovery System
Inside
Page 23
SECTION 8 - CHECKLISTS
Page 24
Page 25
SECTION 9 - FLIGHT PERFORMANCE

All versions, at 450kg MTOW:
Best climb rate speed (flaps 15 degrees, 1 stage)
Min. sink rate at max. AUW (flaps 15 degrees, 1 stage)
Min. sink rate speed
VS1 flaps up stall speed
VS2 flaps 1 stage (15 degrees)
VSo full flaps stall speed
Roll rate at Va
Landing distance, from 15m fence
Fuel consumption
Best glide angle
70 mph (60 kt)

450 fpm
52 mph (45 kt)
47 mph (41 kt)
41 mph (36 kt)
37 mph (32 kt)
45 degrees in 2 sec's
205 metres
See Rotax data.
11:1
C42 FB 100 (Rotax 912S, 100 hp)

Take off distance, to clear 15m fence
Max. climb rate at max. AUW
Vh max level speed at max. AUW
205metres
1000 fpm
124 mph (108 kt)
C42 FB80 (Rotax 912, 80 hp)

Take off distance, to clear 15m fence
Max. climb rate at max. AUW
Vh Max level speed at max. AUW
220metres
700 fpm
120 mph (105 kt)
For MTOW of 472.5kg (when fitted with appropriate modifications) the factors recommended in
the CAA Safety Sense leaflet 7 Aeroplane Performance, also detailed in the GASCO takeoff
and landing performance calculator, should be followed:
for the 5% weight increase allow an extra 10% distance.
Page 26
SECTION 10 - DESCRIPTION OF SYSTEMS

The C42 is a simple aircraft whose structures and systems are readily inspected and maintained.
However, since some of its systems differ from those found on conventional aircraft; this section should
be studied before dismantling, repair or inspection.
10.1
Airframe
Fuselage
A 165 mm diameter aluminium tube runs from nose to tail and carries all the major assemblies:
engine, seats, undercarriage, fuel tank, and tail empennage. The cockpit structure, consisting of
a thin walled aluminium tube frame, includes a welded aluminium box-section frame at its top to
which the wing spars roots attach, and which provides compression load carry-through for both
spars.
The composite seats are supported around their edges by attachment to the cockpit frame.
Around the outboard edges of the seats, some of these loads are passed via the composite
lower fairing to a lateral beam consisting of a 56mm reinforced box section. The ends of this
beam accommodate the wing struts and withstand tension loads from them.
All load carrying (structural) members of the airframe are aluminium alloy tubes; most of which
terminate in spherical bearings.
Wing
The wing has a ladder construction comprising leading and trailing edge tubes, connected by
compression struts at intervals along its span. The triangulated wing struts, terminating at a fixed
point at the top of the undercarriage, brace the wing against fore and aft loads. In normal +g
flight these struts are under tension.
In +g flight both leading and trailing edge tubes inboard of the wing struts junctions, experience
compression loads from the wing struts, as well as direct bending from lift loads.
The wing, tail empennage and all control surfaces are constructed of thin walled aluminium
tubing. They are covered by a reinforced polyester fabric, sewn into complete envelopes and
fitting tightly over their frames.
Undercarriage
The tricycle undercarriage has suspension on all wheels and damping on the main wheels. The
front fork is directly connected to the rudder pedals. Hydraulic disc brakes operate on the main
wheels only.
Main wheels suspension stiffness can be adjusted by varying the air pressure in the damper units
via the valves in their casings. A special high pressure pump is required for this purpose.
10.2
Power Plant
The 80 hp Rotax 912 or the 100 hp Rotax 912S is installed and drives the propeller via a gearbox
with a reduction ratio of 2.27:1 or 2.43:1 respectively. Both power plants are flat 4 cylinder, 4
stroke engines with air and oil cooled cylinders and water-cooled heads. Full descriptions of the
engine, its performance and maintenance requirements are to be found in the Rotax manual.
Engine limitations are given in Section 1.
Page 27
Propellers
The following propeller types are approved for use:
With the 80 hp Rotax:
Warp Drive CS68 composite 2 blade 68 diameter propeller.
Arplast Ecoprop 170R 110/3, 3 Blade 170cm diameter composite propeller.
Kiev Prop 263/1700 3 blade composite propeller with a 1.70m diameter.
With the 100 hp Rotax:
Arplast Ecoprop 170R 3 blade propeller with a diameter of 170 cms (67)
GSC Tech-III 3 Blade 68 diameter wooden propeller.
Neuform CR3-V-R2H 180cm diameter variable pitch propeller.
Kiev Prop 283/1800 3 blade composite propeller with a 1.80m diameter.
All approved types, except the Neuform Variable Pitch Propeller, have blades with groundadjustable pitch and are set to the pitch angles given in Section 1. This pitch angle is prescribed
at a specific radius from the point at which the blade exits from the hub.
The propellers have aluminium alloy hubs machined to close tolerances. This permits secure
clamping of the blade roots under the high centrifugal forces experienced by the blades in
service. Proper blade root securing bolt tension is essential to maintain this security.
Warp Drive and Arplast propellers blades are moulded in composite material, either carbon or
glass fibre in epoxy resin. Blades of this type carry all of their strength and rigidity in the external
skin, which is carbon or glass fibre braid or fabric. See Section 11.
Exhaust system
The engine is fitted with a Hagerman Exhaust and Silencer System. This system is built largely from
stainless steel components.
Fuel Capacity
The C42 has either a 50 litre or 65 litre fuel tank as standard. Both fuel tanks are inter-connectable
so fitting an additional tank doubles the capacity to 100 litres or 130 litres. This capacity is
placarded next to the filler cap.
10.3
Control Systems
Pitch
A central control stick, accessible by both occupants, is located over the fuselage between the
seats. Fore and aft movement of this stick is transferred, via longitudinal push tubes, to a motion
reversal lever installed midway between the cockpit and tail.
This installation also
accommodates the pitch stops. A second push tube, of similar length, runs from this lever to the
elevator horn. A rearward movement of the stick lifts the elevator; forward movement depresses
it.
Each push rod terminates in a spherical bearing (Rose joint) maintaining loads through the
centres of the tubes. The threaded roots of these fittings can be susceptible to failure if bending
loads are applied; it is important to ensure complete freedom of the joints at extremes of their
movements, such that bending loads cannot be applied.
Page 28
Roll
The stick is also connected to a torque tube mounted on top of the fuselage tube between the
seats, and turning on a Rose joint at each end. The rear of the torque tube carries a pair of horns
from which run control cables, one for each side. These cables are led behind and over the
cockpit, via pulleys, to a central bellcrank. From here, motion is transferred via push tubes to a
bellcrank in each wing, mounted on a wing compression strut forward of the aileron. A second
tube links this bellcrank to the aileron horn.
The geometry of the aileron control system produces some asymmetry in the deflections of the
ailerons, effectively eliminating adverse yaw.
Movement of the stick to the right results in a lifting of the right hand aileron and depression of
the left, and vice versa.
Yaw
Dual rudder pedals are mounted on common torque tubes, bearing in bushes installed directly
into the fuselage tube. Control cables run from points near the top of the pedals arms direct to
the rudder horns.
Push rods connected to arms on the font fork, permit direct steering to be made via the rudder
pedals. These push rods are curved to permit slight bending in the event of large opposing
forces from two pilots being applied to the rudder pedals. In this event, a large proportion of the
load is borne by the rudder cables themselves.
Two light springs are fitted to the rudder pedals to aid centering.
Pushing the right rudder pedal forward results in the rudder moving to the right; pushing the left
pedal forward results in the rudder moving to the left.
Trim
An electric pitch trim system is controlled from a rocker switch in the dash. Pressing the top of
the rocker switch lifts the trailing edge of the trim tab and results in a pitch down trim; pressing
the bottom depresses the trim tab and results in a pitch up trim. The switch controls a small servo
motor near the trailing edge of the fixed stabilizer. A short push rod runs from this servo motor to
the trim tab horn. Raising the trim tab in flight results in a down deflection of the trailing edge of
the elevator and a nose down pitch. A panel-mounted meter indicates trim position.
If the trim runs away to one extreme or fails in one position, no undue stick force is required to
maintain control.
Page 29
Brakes
The control stick carries a brake lever with an integrated master cylinder. Hydraulic lines carry
pressure to a small disc brake on each of the main wheels. The brakes work together.
On systems fitted with the Beringer brake modification a pressure limiting device is incorporated
in the system between the brake handle and the brake callipers.
General maintenance to ensure good brake performance
10.4
The engine idle speed must not be higher than 1750 rpm. To avoid a continual fast taxy
situation experiment lowering the idle speed to about 1600 rpm. This will remove the need to
constantly apply the brakes when taxying.
If operating from a hard runway it is inevitable that the brakes will be worked much harder
than if operating from a grass runway. When taxying avoid constantly holding pressure on
the brake lever, this accelerates brake pad wear. Apply the brakes periodically , say every 5
seconds instead.
For the Beringer brake modification consult the Beringer Maintenance Manual appended to
this Owners Handbook.
Jack up each main wheel and spin the wheel checking the brake disc runs centrally
between the brake pads. If the brake disc runs biased over to one side then when the
brakes are applied, contact performance with the two pads will be lost and the brakes
become less efficient. To centralise the brake disc loosen the brake caliper bolts and insert
shims between the caliper and the mounting bracket until the brake disc is centralised.
The brake pads do not have a very thick lining even from new so do not be fooled into
thinking a set of part worn pads are ready for replacement.
Keeping the brake lever pressure quite high ensures good brake performance. The
adjustment plunger on top of the brake fluid cylinder needs to be screwed down
periodically to maintain the pressure in the system.
As the brakes slowly wear and the adjustment plunger is screwed down to its lowest point it
becomes necessary to top up the brake fluid level.
Electrical System
Page 30
Electrical circuit diagrams are given at the end of this manual. Note that the MIPS electronic
engine monitoring system is optional.
Battery
A small lightweight lead acid battery is installed beneath the seats for engine starting. It has a
capacity of 5 amp hours and very high current capability. No maintenance is required, apart
from keeping the contacts clean and dry. The battery is charged from the engines in-built
alternator, via a rectifier-regulator unit.
The engine ignition system is independent of the rest of the electrical system and does not
require the battery to operate.
Fuses
Fuses are provided to protect wiring to all the electrical services with the exception of the starter
motor. If a fuse blows, it is important to determine the cause of the failure before replacing the
fuse. Under no circumstances replace the fuse with one of a higher rating.
Instruments
A variety of electrical instrument configurations is available, with an essential minimum as follows:
Fuel gauge
Tacho
Cylinder Head Temperature gauge (CHT) *
* Note: there may be a significant difference between the CHT reading and that of the coolant
temperature, with the CHT gauge likely to read low, and to have a slower response. Although the
CHT gauge may indicate an acceptable temperature, it must not be assumed that the coolant
temperature lies within limits.
Switches
A master switch provides isolation of the battery from the main bus. The master switch must be
closed (on) before attempting to start the engine, and must remain on to ensure that the
battery is charged properly.
Separate isolating switches are provided for the remaining services or groups of services. Where
a radio is installed, it is wise to turn off the radio switch before starting to reduce the risk of high
spurious voltages damaging the radio.
NOTE: - The ignition switches stop the engine by grounding the ignition circuit. The engine is
started and runs with the switches open, and is stopped by closing the switches. The ignition
switches are therefore mounted in the reverse sense to the other switches to enable the normal
aviation switch sense to be maintained. ie. up for ON, down for OFF.
It is also important to note that disconnection of the ignition switch wires, by accident or during
maintenance, renders the engine live. Great care must be exercised in this case to ensure that
the engine cannot be started accidentally. Normally remove the spark plugs caps.
Page 31
10.5
Ballistic Recovery System

The ballistic recovery system consists of a parachute attached to the airframe designed to lower
the entire aircraft and occupants to the ground.
The parachute is mounted towards the tail end of the fuselage, on top of the pair of bracing
tubes inside the fuselage fairing. The parachute is fitted inside a fabric container, and it is pulled
out of the aircraft by a small rocket motor attached close to the parachute container. The
bridles from the parachute are attached to the airframe on the cross-tube aft of the seats, and
to the main tube via the front strut forward of the cockpit.
Deployment is activated by pulling a handle located above the cockpit area between the
pilots. When on the ground the handle is secured against accidental activation by a small
padlock, the key for which should be attached to the aircraft master key.
Page 32
SECTION 11 - INSPECTION AND MAINTENANCE

11.1
Daily Inspection / Pre-flight Inspection

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21
22.
23.
Engine and cowling secure and undamaged.

Check coolant level correct.
Check oil level within limits.*
Propeller clean and undamaged1, bolts secure.
Front gear; tyre pressure, tyre condition and tyre creep.
Left main gear; tyre pressure and condition.
Left side wing, structure and covering.
Left wing strut attachment secure.
Left aileron, control linkage and hinges secure.
Left flap, control linkage and hinges secure.
Left side of the fuselage, undamaged
Tail group secure and surfaces undamaged.
Elevator hinges and control linkage secure.
Trim tab and linkage secure.
Rudder hinges and control cables secure.
Repeat items 4 thro 11 for right side.
Fuel filler cap secure.
Windscreen clear and undamaged.
ASI pitot unobstructed and fully extended.
Cockpit area inside and out, check controls full movement, free and correct sense.
Instruments serviceable.
Open fuel tank sump drain and check for contamination.
Check tank water drain for leaks.
*When checking the oil level it may be necessary to pump the oil back into the reservoir to
obtain a correct reading and to avoid overfilling. This can be done by removing the oil filler cap
and ensuring the master switch and magnetos are off and rotating the propeller ONLY in the
operating direction until a gurgling sound is heard from the reservoir tank.
With composite propellers, minor damage to the external surface, such as a deep scratch which
breaches the outside fabric, can result in significant loss of strength and a dangerous condition. For this
reason it is important to inspect the blades carefully before flight. Look particularly for scratches along
the chord of the blade which may have severed one or more yarns of fibre. When in doubt, seek expert
advice.
Neuform propellers must be returned to Neuform in Germany for an inspection every 500 hours or
2 years whichever comes first. Please refer to your propeller operating manual.
Page 33
11.2
Periodic Maintenance and Inspection

Servicing, maintenance and repair work on this class of aircraft can be performed by the pilot.
Certain work must be signed off in the Engine and Airframe Logbook by a PFA or BMAA
Inspector. Definitions of Pilot Maintenance work is obtainable from the BMAA and PFA. Use only
approved spare parts and never fit damaged parts.
All servicing, maintenance and repair work on the aircraft, including the engine, propeller and
ballistic recovery system (if fitted), should be recorded in the Engine and Airframe Logbook.
Every 25 hours inspection

Engine: Check 25 hour inspection items in accordance with the ROTAX manual.
Fuel system
1.
2.
3.
Check tank internally for cleanliness.

Check fuel filter for cleanliness.
Check all fuel lines for degradation.
Airframe
1.
2.
3.
4.
Check control stick for freedom without undue friction.

Check safety lock plates at the bearings at front and rear ends of control stick torsion tube.
Check that rod end bearings on elevator push rods suffer no bending at each extreme lateral
position of stick (aileron limits).
Check all lock nuts for tightness.
Wing
1.
2.
3.
4.
Check internal bracing wires for adequate tension.

Check freedom of ailerons.
Check aileron and flap hinges for wear.
Check aileron and flap hinge bolts for tightness (cannot rotate)
Tail Empennage
1.
2.
3.
4.
Check rudder hinges for wear.

Check elevator hinges for wear.
Check rudder and elevator hinge bolts for tightness (cannot rotate)
Check rudder cables for wear at fairleads.
50-Hours Inspection
Engine:
Check inspection items in accordance with the ROTAX manual.
Additionally to the 25 hour schedule:
1.
2.
3.
4.
5.
6.
7.
8.
Check rudder and aileron cables for wear and damage.

Check brake pads, brake disks and brake function.
Lubricate the nose leg bearings with a grease gun at the upper and lower grease nipples.
Check rudder cable tension, 25 to 35 kgf.
Check aileron cable tension, 18 to 24 kgf
Change the fuel filter.
Check stub axles for cracks.
Check seat support tube cannot rotate.
Page 34
100-Hour or Annual Inspection

Engine:
Perform 50 hours checks in accordance with ROTAX manual.
Additionally to the 50 hour schedule:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Clean, grease and check security of ball joints on steering rods at foot pedals and operating bar
of front wheel.
Clean, grease and check security of rod end bearings at stick torsion tube.
Clean, grease and check freedom of throttle control; ensure that the cable cannot stick, even
when closed slowly.
Clean, grease and check security of all ball and fork hinges at each aileron push rod end.
Check all hinges for excess play. Clean and grease all hinges and remove rudder to check clevis
pins for excess wear.
Check all lock nuts for proper installation; check 2 threads showing.
Check central and internal wing-mounted aileron bellcranks for freedom and security. Clean
and grease bellcrank ball connections, and, if necessary, bellcrank bearings.
Check cross bolt and connections of elevator motion reversal lever for security and wear.
Check bearing of reversing lever for wear and freedom. Clean and grease central bearing.
Clean, grease and check security of rod-end bearings of elevator push rods; tighten and Loctite
locking nuts.
Remove exhaust and check for cracks especially around cockpit heater jacket.
Replace cockpit carbon monoxide detector in accordance with manufacturers instructions.

11.3 Jacking the Aircraft
Either of the main wheels can be brought clear of the ground by one person lifting the wing at the top
of the wing struts. (Never apply any significant up load to the centre of the struts). The aircraft can then
be chocked by placing a wooden block under the bottom part of the stub axle. This is also a suitable
jacking point where a second person is not available to lift the wing.
The nose wheel is easily lifted by applying a load to the rear fuselage, just forward of the tail. Where one
person only is available, place weights on the tail, suitably padded to prevent damage to the fabric,
until the nose wheel becomes light. Place a piece of timber under the tail skid, then push the tail down
on to it. Add further weights to the tail to stabilise the aircraft in this attitude.
11.3
Cleaning and Repair of the wing fabric
Cleaning
Clean the wing coverings with warm water and a mild detergent, such as washing up liquid, to remove
oil. Never use solvents. All metal parts are anodized aluminum or stainless steel and need no special
attention.
Dirt or mud on wing surfaces should be removed with clean water. Avoid the use of a pressure washer
or hose pipe as this can introduce water into places it shouldnt go, (engine, fuel tank, pitot head, pilots
seat).
Repair
Repair even the smallest tears in the covering fabric.
Carefully clean the area around the tear, then attach a small patch with contact adhesive covering an
area at least 15 mm larger than the damage all round. Alternatively apply a small patch of selfadhesive material. For larger areas of damage, consult the importers, Performance Aviation Ltd.
In the event of technical problems, contact Performance Aviation Ltd.
Page 35
SECTION 12 - WING RIGGING AND DE-RIGGING, FLYING WITH DOORS REMOVED

12.1.
Attaching the wings to the folding mechanism. (Optional).

The C-42 has an optional folding wing which minimises hangar space. For road transport
however you must remove the wings completely. To attach the wings to the folding system:
Step 1. Fit the jockey wheel to the stern post, fit the traingular wooden support brackets to the
bottom of the tailplane struts, with the aluminium strip uppermost.
Step 2. Remove the stop ring from the slide tube in the cockpit roof.
Step 3. Place a wing parallel to the fuselage with its tip supported on the tail by the wooden
support bracket.
(With both wings folded back and supported by the tail, the aircraft will rock back to sit
on its tail. With only one wing on the tail, the aircraft can be tipped forward to a stable
attitude resting on its nose wheel. Be aware of these movements during rigging and
derigging operations. Take care to protect the wing from damage by contact with the
ground).
Step 4. Lift the wing root and slide the attachment block (roller) 2 inches (5cm) over the slide
tube.
Step 5. Attach the stop cable on the leading edge to the quick link on the slide tube.
Step 6. Attach the stop ring to the end of the slide tube.
If both wings are in the folded back position the C42 can be easily moved by one person
into a small hangar space.
12.2
Rigging the wings

If you are tall but weak, it may be easier to manipulate the wing during rigging by holding it at its
tip. If you are short and strong, the better handling point is the top of the wing struts. If you are
short and weak, fetch a friend. If you are short, weak and friendless, don't derig.
Before attempting rigging, take a look at the wing roots and the way in which the rigging
mechanism works. Note that the fulcrum (the roller bracket) is located near the wing root, and
also in line with the rear spar attachment point. The front spar attachment point however is
located some way inboard. This means that lifting the wing tip will result in the front spar clearing
its fitting before the rear one. This can be used to advantage during rigging.
Step 1. Ensure that the spar channels in the cockpit roof are aligned with the top surface of the
cockpit roof frame. Lock the controls, place the flap lever in the fully up position and
ensure the brake is on.
Step 2. Bring the left wing strut into its correct position on the left wing and attach the auxiliary
(jury) struts on the front and rear wing struts to the leading and trailing edge fittings.
Step 3. If this is the first side to be rigged and the second wing half is still resting on the tail, lift the
wing at its tip with one hand. With the other hand, steadily lift the tail so that the aircraft
rests on its nosewheel.
Step 4. Carry the wing into its 90 position relative to the fuselage, taking care not to damage
the door and fuselage with the front spar.
Step 5. Turn the wing into a horizontal position and push it gently towards the fuselage.
Step 6. Lifting the tip, slowly insert the wing roots into position in their channels, leading edge first.
Page 36
It may be necessary to gently rock and twist the wing to engage the spar hooks on to
their pins.
Step 7. Ensure that front and rear wing spars are properly engaged in their channels. Then insert
the lower end of the wing struts into the open box-section end at the top of the shock
absorbers.
Step 8. Attach front wing bolt and safety pin, using the tool provided.
Step 9. Attach rear wing bolt and safety pin.
Step10.Attach the strut bolt through the box-section end and lower steel block of the wing
struts ends. Install the safety pin.
Step11.Check that all three bolts have their safety pins installed.
Step12.As a final check, lift the wing at the wing tip to ensure proper attachment of the wing
strut block to the box-section end.
Step 13.Connect the pitot tube to its fitting situated to the left of the pilots headrest. Pull out the
pitot tube forwards to its full extent.
Step 14.Repeat steps 1 through 12 for the other wing. Now you may remove the control lock.
Step15.Attach right and left aileron push rods to the central bellcrank connection. Carefully
ensure that the slide mechanisms of the special link connectors are properly engaged
(closed and locked).
Step 16.On the flap drive tube, take the split sleeve fitted around the sprung taper pins (and
through which they protrude), spread it a little, then rotate it over the pins. Using this
sleeve as an aid, squeeze it, thus compressing the pins. Then move the sleeve so that the
drive fitting moves freely on its tube.
Step 17.Align the flap root tube and its drive fitting on the fuselage. Slide the flap drive fitting
over the junction so that its cutaways engage snugly in the roots of the flap frame tubes
and the sprung pins are fully out. Rotate the split sleeve so that its holes align with the
tips of the pins again, permitting the pins to spring out fully. Left and right landing flaps
must be securely locked and it may be necessary to wiggle the fitting a little to ensure
proper engagement, particularly when the aircraft is new.
Step 18.Position and fasten the wing centre section (cockpit roof).
12.3
Folding the wings to hangar the aircraft:

Step 1. Apply the brake. Fit the dolly wheel to the stern post.
Step 2. Push in the pitot tube on the left wing.
Step 3. Remove wing centre section.
Step 4. Disconnect the pitot tube from its fitting above the pilots seat back.
Step 5. Place a triangular wooden support bracket (supplied) on to the lower part of the
tailplane strut at each side, with the aluminium strip uppermost.
Step 6. Set the flap control in its fully up position.
Step 7. Disconnect the landing flaps by first spreading and rotating the aluminium split sleeve on
the flap drive fitting. Then push in the spring loaded pins by squeezing the split sleeve.
Page 37
Step 8. With the trailing edge of the flap resting on your shoulder, squeeze the split sleeve with
one hand and, holding the knurled ring in the other, push the assembly inboard until it
clears the drive tube junction. Lower the flap gently.
Step 9. Unlock the aileron push rods from central bellcrank connections.
Step 10.Remove the keep rings from the front and rear spar pins and the lower strut pin, at each
side, (total 6 rings).
Step 11.Unlock the strut block from lower box section end by removing the strut pin, using the
special tool provided.
Step 12.Unlock the rear wing spar by removing its pin.
Step 13.Unlock front wing spar by removing its pin, hold down the top of the screen to prevent
damage.
Step 14.Close the door.
Step 15.Lift the left wing at its wing tip, or strut tops, so that wing strut block leaves the square
box-section end. By lifting the wing high you will first disconnect the front spar hook from
its pin and frequently the rear spar at the same time. If the rear spar does not disengage,
gently rock the wing from side to side, pulling gently and twisting it until it does.
Step 16.Pull out the wing until it stops on the stop wire. Ensure that the stop wire runs over the
TOP of the aileron operating push tube before folding back the wing.
Step 17.Draw back the wing away from the fuselage until the movement is stopped by the stop
ring on the slide tube.
Step 18.Rotate the wing into a vertical position - underside of the wing to the front; trailing edge
down.
Always hold the wing tip higher than the root to prevent damage to the door and fuselage with
the spars' ends.
Step 19.Carry the wing tip back into a position parallel to the fuselage. If the wing has been
supported at the strut tops, it will be necessary to set it down and pick it up again by its
tip for the next step. During this operation, ensure that the wing cannot tip forwards by
walking your hands along the leading edge to the tip.
Note that the aircraft will tip back upon folding the second wing.
Step 20.Separate the Velcro for 2 or 3 inches (50 to 75 mm) along the aileron root at a point
where the support bracket meets it.
Step 21.Place the wing trailing edge onto the retainer bracket on the tail.
Step 22.Remove the pin from the top of each jury strut.
Step 23.Rotate the jury struts carefully so that they lie parallel and next to each other.
Step 24.Undo the inboard zip on the wings lower surface, adjacent to the jury struts.
Step 25.Fold in the main struts to lie flat against the lower wing surface. Secure the strut bottom
with the bungee attached to the wing root.
Step 26.Fold back the right wing according to steps 1 to 25.
Page 38
12.4
Flying Without Doors Aerosport MOD C42/019
Both doors must be removed. It is not permissible to remove just one door.
Ensure when flying with the doors removed that there are no loose items, take special care to check
under the seats. Items stowed under the seat must be in a soft container that is unable to slide forward
or interfere with the throttle (A suitable container is available from the manufacturer). Also wear suitable
clothing that will not flap or flail around in the cockpit. It is recommended that maps are placed in a
suitable map holder that can be anchored to the pilot or passenger.
Follow the instructions for removing and replacing the doors carefully.
Open door and remove safety clip from gas strut and safety ring from rear clevis pin but do not
unclip gas strut or remove clevis pin at this stage.
Place a piece of tape over the hinge bolt to prevent it turning in or out.
Carefully support the door and unclip the door strut ball joint then remove the clevis pin.
Carefully slide the door off the front locating spigot & store the door somewhere safe.
Re-fitting is simply a reversal making certain to re-fit safety rings & clips.
Have your work checked by your local PFA or BMAA inspector.
Page 39
SECTION 13 - SETTING (RIGGING) AND MISCELLANEOUS DATA

13.1
Incident angle of wing with respect to main fuselage tube: 8

Note:
13.2
The incident angle is defined as the angle between a line parallel to the fuselage tube
and a line joining the undersides of the leading and trailing edge tubes at their roots.
Angle of stabilizer with respect to the main fuselage tube: 7

Note:
The stabilizer angle is defined as the angle between a line parallel to the fuselage tube
and a line joining the undersides of the leading edge and trailing edge of the stabilizer.
Angle difference between wing and stabilizer: 1

13.3
Control Surface Deflections

Aileron
Up 20 2 or 85 mm, 9 mm measured 250 mm from the hinge axis.

Down 14 2 or 60 mm, 9 mm measured 250 mm
from the hinge axis.
Area
Elevator
0,58 m2 per side.
Up 30 3 or 205 mm + 21 mm measured 410 mm from the hinge axis.

Down 20 3. Or 140 mm + 21 mm measured 410mm from the hinge axis.
Area
Rudder L/R
32 3 or 217 mm + 21 mm measured 410mm from the hinge axis.

Area
0.44 m2
Fin
Area
0.61 m2
Stabilizer
Area
1,42 m2 total
Flaps
- 4.5 -15
- 42
Relative to the fuselage tube.
Area
Elevator Trim Tab

13.4
0.82 m2 total
0.46 m2 per side.

Up
1 to 5
Down 253 (relative to elevator)
Air pressure for tyres and shock absorber:

Main wheels
1.8 - 2.5 bar
26 to 36 psi.
Front wheel
1.5 - 1.8 bar
22 to 26 psi.
Shock absorbers
29 - 33 bar
425 to 486 psi
A special pressure pump, available from Performance Aviation Ltd, is used for setting the shock absorber
pressures.
Page 40
Circuit Diagram Standard Installation.
Page 41
Circuit Diagram Trim Tab
Page 42
Circuit Diagram MIP installation.

Page 43

Ikarus C42 Pilot Operating Handbook

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Ikarus C42 Pilot Operating Handbook

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ikarus C42 Pilot Operating Handbook

Uploaded by

Copyright:

Available Formats

C42

C42 Owners Manual (Microlight)

C42 Owners Manual

This Manual belongs to aircraft reg

Type IKARUS C42 FB

Series Build Aircraft

IKARUS C42 FB80, C42 FB100

Type Approval Data Sheet (TADS) No. BM 68

CAA Company Approval No DAI/9949/11

This handbook should be kept with the aircraft.

C42 Owners Manual (Microlight)

Format change only

Tyre pressure change

Warp Drive 3 blade prop 80hp Version

50 hour Inspection schedule

Flying with doors removed

B model information added (carburettor heat and

Kiev Prop for Rotax 912UL 80hp added.

C42 Owners Manual (Microlight)

IKARUS C-42 FLIGHT AND OPERATORS MANUAL

C42 Owners Manual (Microlight)

SECTION 1 - AIRFRAME AND ENGINE LIMITATIONS

265.5 kg 100 hp 912S

Max gross weight:

288 kg 100 hp 912S

135 sq ft, 12.5 sq.m

4g (at all speeds)

350 mm aft of datum (366mm at M>450kg).

37 to 72 mph (32 to 63 kt) full flap operating range.

Control Deflection Limits

VA is the maximum speed permitted in turbulent conditions. Full deflection of the

C42 Owners Manual (Microlight)

5800 rpm (5 minutes max)

RPM Meter Markings: yellow 5500-5800 rpm (80 HP)

Maximum coolant temperature

Maximum Cylinder Head Temp. (CHT)

C42 Owners Manual (Microlight)

SECTION 2 - OPERATIONAL LIMITATIONS

must not be flown in aerobatic manoeuvres.

must not be flown at bank angles beyond 60 degrees.

must be flown under daylight, VFR conditions only.

must not be flown in known airframe icing conditions.

Always follow the appropriate regulations for this category of aircraft.

C42 Owners Manual (Microlight)

SECTION 3 - OPERATION OF THE POWERPLANT

CAUTION: Never handle the propeller with the ignition on.

Main fuel valve,

Open the main fuel valve - dont forget!

Failure to let the oil temperature reach 50C can result in

C42 Owners Manual (Microlight)

Takeoff and climb:

C42 Owners Manual (Microlight)

Variations in rpm and cruise performance occur with different loads.

The maximum speed in cruising flight is 118 mph (103 kt).

This maximum speed applies only in smooth conditions with no turbulence. In

Slow flight, stalling and use of flaps:

C42 Owners Manual (Microlight)

Descents, landing and roll out: