Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Fuel Injection: Fuel Injection Is The Introduction of Fuel in An Internal

Download as pdf or txt
Download as pdf or txt
You are on page 1of 14

Fuel injection

Fuel injection is the introduction of fuel in an internal


combustion engine, most commonly automotive
engines, by the means of an injector.

All diesel engines use fuel injection by design. Gas


engines can use gasoline direct injection, where the fuel
is directly delivered into the combustion chamber, or
indirect injection where the fuel is mixed with air before
the intake stroke.

On petrol engines, fuel injection replaced carburetors


from the 1980s onward.[1] The primary difference
between carburetion and fuel injection is that fuel
injection atomizes the fuel through a small nozzle under Fuel rail connected to the injectors that are
high pressure, while a carburetor relies on suction mounted just above the intake manifold on a four-
created by intake air accelerated through a Venturi tube cylinder engine.
to draw the fuel into the airstream.

Contents
Objectives
Benefits
Environmental benefits
History and development
Development in diesel engines
Development in gasoline/petrol engines
Mechanical injection
Electronic injection
Elimination of carburetors
System components
System overview
Determining how much fuel to supply
Supplying the fuel to the engine
EFI gasoline engine components
Engine control unit
Fuel injector
Target air–fuel ratios
Various injection schemes
Single-point injection
Continuous injection
Central port injection
Multipoint fuel injection
Direct injection
Diesel engines
Gasoline engines
Swirl injection
Maintenance hazards
Notes
Further reading
External links

Objectives
The functional objectives for fuel injection systems can vary. All share the central task of supplying fuel to
the combustion process, but it is a design decision how a particular system is optimized. There are several
competing objectives such as:

Power output
Fuel efficiency
Emissions performance
Running on alternative fuels
Reliability
Driveability and smooth operation
Initial cost
Maintenance cost
Diagnostic capability
Range of environmental operation
Engine tuning

Modern digital electronic fuel injection systems optimize these competing objectives more effectively and
consistently than earlier fuel delivery systems (such as carburetors). Carburetors have the potential to
atomize fuel better (see Pogue and Allen Caggiano patents).

Benefits
Benefits of fuel injection include smoother and more consistent transient throttle response, such as during
quick throttle transitions, easier cold starting, more accurate adjustment to account for extremes of ambient
temperatures and changes in air pressure, more stable idling, decreased maintenance needs, and better fuel
efficiency.

Fuel injection also dispenses with the need for a separate mechanical choke, which on carburetor-equipped
vehicles must be adjusted as the engine warms up to normal temperature. Furthermore, on spark ignition
engines, (direct) fuel injection has the advantage of being able to facilitate stratified combustion which has
not been possible with carburetors.

It is only with the advent of multi-point fuel injection certain engine configurations such as inline five-
cylinder gasoline engines have become more feasible for mass production, as traditional carburetor
arrangements with single or twin carburetors can not provide even fuel distribution between cylinders,
unless a more complicated individual carburetor per cylinder is used.

Fuel injection systems are also able to operate normally regardless of orientation, whereas carburetors with
floats are not able to operate upside down or in microgravity, such as that encountered on airplanes.

Environmental benefits

Fuel injection generally increases engine fuel efficiency. With the improved cylinder-to-cylinder fuel
distribution of multi-point fuel injection, less fuel is needed for the same power output (when cylinder-to-
cylinder distribution varies significantly, some cylinders receive excess fuel as a side effect of ensuring that
all cylinders receive sufficient fuel).

Exhaust emissions are cleaner because the more precise and accurate fuel metering reduces the
concentration of toxic combustion byproducts leaving the engine. The more consistent and predictable
composition of the exhaust makes emissions control devices such as catalytic converters more effective and
easier to design.

History and development


Herbert Akroyd Stuart developed the first device with a design similar to modern fuel injection [2], using a
'jerk pump' to meter out fuel oil at high pressure to an injector. This system was used on the hot-bulb engine
and was adapted and improved by Bosch and Clessie Cummins for use on diesel engines (Rudolf Diesel's
original system employed a cumbersome 'air-blast' system using highly compressed air). Fuel injection was
in widespread commercial use in diesel engines by the mid-1920s.

An early use of indirect gasoline injection dates back to 1902, when French aviation engineer Leon
Levavasseur installed it on his pioneering Antoinette 8V aircraft powerplant, the first V8 engine of any type
ever produced in any quantity.[3]

Another early use of gasoline direct injection was on the Hesselman engine invented by Swedish engineer
Jonas Hesselman in 1925.[4][5] Hesselman engines use the ultra lean-burn principle; fuel is injected toward
the end of the compression stroke, then ignited with a spark plug. They are often started on gasoline and
then switched to diesel or kerosene.[6]

Direct fuel injection was used in notable World War II aero-engines such as the Junkers Jumo 210, the
Daimler-Benz DB 601, the BMW 801, the Shvetsov ASh-82FN (M-82FN). German direct injection petrol
engines used injection systems developed by Bosch from their diesel injection systems. Later versions of the
Rolls-Royce Merlin and Wright R-3350 used single point fuel injection, at the time called "Pressure
Carburettor". Due to the wartime relationship between Germany and Japan, Mitsubishi also had two radial
aircraft engines using fuel injection, the Mitsubishi Kinsei (kinsei means "venus") and the Mitsubishi Kasei
(kasei means "mars").

Alfa Romeo tested one of the first electronic injection systems (Caproni-Fuscaldo) in Alfa Romeo 6C 2500
with "Ala spessa" body in 1940 Mille Miglia. The engine had six electrically operated injectors and were fed
by a semi-high-pressure circulating fuel pump system.[7]

Development in diesel engines

All diesel engines (with the exception of some tractors and scale model engines) have fuel injected into the
combustion chamber. See Diesel engine.
Development in gasoline/petrol engines

Mechanical injection

The invention of mechanical injection for gasoline-fueled aviation


engines was by the French inventor of the V8 engine configuration,
Leon Levavasseur in 1902.[3] Levavasseur designed the original
Antoinette firm's series of V-form aircraft engines, starting with the
Antoinette 8V to be used by the aircraft the Antoinette firm built that
Levavasseur also designed, flown from 1906 to the firm's demise in
1910, with the world's first V16 engine, using Levavasseur's port
injection and producing around 100 hp (75 kW; 101 PS) flying an
An Antoinette mechanically fuel-
Antoinette VII monoplane in 1907.
injected V8 aviation engine of 1909,
mounted in a preserved Antoinette
The first post-World War I example of direct gasoline injection was
VII monoplane aircraft.
on the Hesselman engine invented by Swedish engineer Jonas
Hesselman in 1925.[8][9] Hesselman engines used the ultra-lean-burn
principle and injected the fuel in the end of the compression stroke
and then ignited it with a spark plug, it was often started on gasoline and then switched over to run on diesel
or kerosene. The Hesselman engine was a low compression design constructed to run on heavy fuel oils.

Direct gasoline injection was applied during the Second World War to almost all higher-output production
aircraft powerplants made in Germany (the widely used BMW 801 radial, and the popular inverted inline
V12 Daimler-Benz DB 601, DB 603, and DB 605, along with the similar Junkers Jumo 210G, Jumo 211,
and Jumo 213, starting as early as 1937 for both the Jumo 210G and DB 601), the Soviet Union (Shvetsov
ASh-82FN radial, 1943, Chemical Automatics Design Bureau - KB Khimavtomatika) and the USA (Wright
R-3350 Duplex Cyclone radial, 1944).

Immediately following the war, hot rodder Stuart Hilborn started to offer mechanical injection for race cars,
salt cars, and midget racers,[10] well-known and easily distinguishable because of their prominent velocity
stacks projecting upwards from the engines on which they were used.

The first automotive direct injection system used to run on gasoline was developed by Bosch, and was
introduced by Goliath for their Goliath GP700 automobile, and Gutbrod in 1952. This was basically a
specially lubricated high-pressure diesel direct-injection pump of the type that is governed by the vacuum
behind an intake throttle valve. (Modern diesels only change the amount of fuel injected to vary output;
there is no throttle.) This system used a normal gasoline fuel pump, to provide fuel to a mechanically driven
injection pump, which had separate plungers per injector to deliver a very high injection pressure directly
into the combustion chamber. The 1954 Mercedes-Benz W196 Formula 1 racing car engine used Bosch
direct injection derived from wartime aircraft engines. Following this racetrack success, the 1955 Mercedes-
Benz 300SL, the first production sports car to use fuel injection, used direct injection. The 1955 Mercedes-
Benz 300SLR, in which Stirling Moss drove to victory in the 1955 Mille Miglia and Pierre Levegh crashed
and died in the 1955 Le Mans disaster, had an engine developed from the W196 engine. The Bosch fuel
injectors were placed into the bores on the cylinder wall used by the spark plugs in other Mercedes-Benz
six-cylinder engines (the spark plugs were relocated to the cylinder head). Later, more mainstream
applications of fuel injection favored the less-expensive indirect injection methods.

Chevrolet introduced a mechanical fuel injection option, made by General Motors' Rochester Products
Division, for its 283 V8 engine in 1956 (1957 U.S. model year). This system directed the inducted engine air
across a "spoon shaped" plunger that moved in proportion to the air volume. The plunger connected to the
fuel metering system that mechanically dispensed fuel to the cylinders via distribution tubes. This system
was not a "pulse" or intermittent injection, but rather a constant flow system, metering fuel to all cylinders
simultaneously from a central "spider" of injection lines. The fuel
meter adjusted the amount of flow according to engine speed and
load, and included a fuel reservoir, which was similar to a
carburetor's float chamber. With its own high-pressure fuel pump
driven by a cable from the distributor to the fuel meter, the system
supplied the necessary pressure for injection. This was a "port"
injection where the injectors are located in the intake manifold, very
near the intake valve. A 1959 Corvette small-block 4.6 litre
V8 with Rochester mechanical fuel
In 1956, Lucas developed its injection system, which was first used injection
for Jaguar racing cars at Le Mans. The system was subsequently
adopted very successfully in Formula One racing, securing
championships by Cooper, BRM, Lotus, Brabham, Matra, and Tyrrell in the years 1959 through 1973.[11]
While the racing systems used a simple fuel cam for metering, a more sophisticated Mk 2 vacuum based
shuttle metering was developed for production cars. This mechanical system was used by some Maserati,
Aston Martin, and Triumph models between 1963 and 1975.[12]

During the 1960s, other mechanical injection systems such as Hilborn were occasionally used on modified
American V8 engines in various racing applications such as drag racing, oval racing, and road racing.[13]
These racing-derived systems were not suitable for everyday street use, having no provisions for low speed
metering, or often none even for starting (starting required that fuel be squirted into the injector tubes while
cranking the engine). However, they were a favorite in the aforementioned competition trials in which
essentially wide-open throttle operation was prevalent. Constant-flow injection systems continue to be used
at the highest levels of drag racing, where full-throttle, high-RPM performance is key.[14]

In 1967, one of the first Japanese designed cars to use mechanical fuel injection was the Daihatsu
Compagno.

Another mechanical system, made by Bosch called Jetronic, but injecting the fuel into the port above the
intake valve, was used by several European car makers, particularly Porsche from 1969 until 1973 in the 911
production range and until 1975 on the Carrera 3.0 in Europe. Porsche continued using this system on its
racing cars into the late seventies and early eighties. Porsche racing variants such as the 911 RSR 2.7 & 3.0,
904/6, 906, 907, 908, 910, 917 (in its regular normally aspirated or 5.5 Liter/1500 HP turbocharged form),
and 935 all used Bosch or Kugelfischer built variants of injection. The early Bosch Jetronic systems were
also used by Audi, Volvo, BMW, Volkswagen, and many others. The Kugelfischer system was also used by
the BMW 2000/2002 Tii and some versions of the Peugeot 404/504 and Lancia Flavia.

A system similar to the Bosch inline mechanical pump was built by SPICA for Alfa Romeo, used on the
Alfa Romeo Montreal and on U.S. market 1750 and 2000 models from 1969 to 1981. This was designed to
meet the U.S. emission requirements with no loss in performance and it also reduced fuel consumption.

Electronic injection

Because mechanical injection systems have limited adjustments to develop the optimal amount of fuel into
an engine that needs to operate under a variety of different conditions (such as when starting, the engine's
speed and load, atmospheric and engine temperatures, altitude, ignition timing, etc.) electronic fuel injection
(EFI) systems were developed that relied on numerous sensors and controls. When working together, these
electronic components can sense variations and the main system computes the appropriate amount of fuel
needed to achieve better engine performance based on a stored "map" of optimal settings for given
requirements.[15] in 1953, the Bendix Corporation began exploring the idea of an electronic fuel injection
system as a way eliminate the well known problems of traditional carburetors.[16]
The first commercial EFI system was the "Electrojector" developed by Bendix and was offered by American
Motors Corporation (AMC) in 1957.[17][18] The Rambler Rebel, showcased AMC's new 327 cu in (5.4 L)
engine.[19] The Electrojector was an option and rated at 288 bhp (214.8 kW).[20] The EFI produced peak
torque 500 rpm lower than the equivalent carburetored engine[13] The Rebel Owners Manual described the
design and operation of the new system.[21] An electronic control box located under the dashboard uses
information from various sensors for engine starting, idling, and acceleration requirements to determine
optimal timing of the fuel charge by electrically actuating the injectors.[21] The cost of the EFI option was
US$395 and it was available on 15 June 1957.[22] According to AMC, the price would be significantly less
than Chevrolet's mechanical fuel injection option.[23] Electrojector's teething problems meant only pre-
production cars were so equipped: thus, very few cars so equipped were ever sold[24] and none were made
available to the public.[25] The EFI system in the Rambler ran fine in warm weather, but suffered hard
starting in cooler temperatures.[22]

Chrysler offered Electrojector on the 1958 Chrysler 300D, DeSoto Adventurer, Dodge D-500, and Plymouth
Fury, arguably the first series-production cars equipped with an EFI system.[23] It was built Bendix.[23] The
early electronic components were not equal to the rigors of underhood service, however, and were too slow
to keep up with the demands of "on the fly" engine control. Most of the 35 vehicles originally so equipped
were field-retrofitted with 4-barrel carburetors. The Electrojector patents were subsequently sold to Bosch.

Bosch developed an electronic fuel injection system, called D-Jetronic (D for Druck, German for
"pressure"), which was first used on the VW 1600TL/E in 1967. This was a speed/density system, using
engine speed and intake manifold air density to calculate "air mass" flow rate and thus fuel requirements.
This system was adopted by VW, Mercedes-Benz, Porsche, Citroën, Saab, and Volvo. Lucas licensed the
system for production in Jaguar cars, initially in D-Jetronic form before switching to L-Jetronic in 1978 on
the XK6 engine.

Bosch superseded the D-Jetronic system with the K-Jetronic and L-Jetronic systems for 1974, though some
cars (such as the Volvo 164) continued using D-Jetronic for the following several years. In 1970, the Isuzu
117 Coupé was introduced with a Bosch-supplied D-Jetronic fuel injected engine sold only in Japan. In 1984
Rover fitted Lucas electronic fuel injection, which was based on some L-Jetronic patents, to the S-Series
engine as used in the 200 model.

In Japan, the Toyota Celica used electronic, multi-port fuel injection


in the optional 18R-E engine in January 1974.[26] Nissan offered
electronic, multi-port fuel injection in 1975 with the Bosch L-
Jetronic system used in the Nissan L28E engine and installed in the
Nissan Fairlady Z, Nissan Cedric, and the Nissan Gloria. Nissan also
installed multi-point fuel injection in the Nissan Y44 V8 engine in
the Nissan President. Toyota soon followed with the same
technology in 1978 on the 4M-E engine installed in the Toyota
Crown, the Toyota Supra, and the Toyota Mark II. In the 1980s, the
Isuzu Piazza and the Mitsubishi Starion added fuel injection as Chevrolet Cosworth Vega engine
standard equipment, developed separately with both companies showing Bendix electronic fuel
history of diesel powered engines. 1981 saw Mazda offer fuel injection (in orange).
injection in the Mazda Luce with the Mazda FE engine and, in 1983,
Subaru offered fuel injection in the Subaru EA81 engine installed in
the Subaru Leone. Honda followed in 1984 with their own system, called PGM-FI in the Honda Accord, and
the Honda Vigor using the Honda ES3 engine.

The limited production Chevrolet Cosworth Vega was introduced in March 1975 using a Bendix EFI system
with pulse-time manifold injection, four injector valves, an electronic control unit (ECU), five independent
sensors, and two fuel pumps. The EFI system was developed to satisfy stringent emission control
requirements and market demands for a technologically advanced responsive vehicle. 5000 hand-built
Cosworth Vega engines were produced but only 3,508 cars were sold through 1976.[27]

The Cadillac Seville was introduced in 1975 with an EFI system made by Bendix and modelled very closely
on Bosch's D-Jetronic. L-Jetronic first appeared on the 1974 Porsche 914, and uses a mechanical airflow
meter (L for Luft, German for "air") that produces a signal that is proportional to "air volume". This
approach required additional sensors to measure the atmospheric pressure and temperature, to ultimately
calculate "air mass". L-Jetronic was widely adopted on European cars of that period, and a few Japanese
models a short time later.

In 1980, Motorola (now NXP Semiconductors) introduced the first electronic engine control unit, the EEC-
III.[28] Its integrated control of engine functions (such as fuel injection and spark timing) is now the standard
approach for fuel injection systems. The Motorola technology was installed in Ford North American
products.

Elimination of carburetors
In the 1970s and 1980s in the U.S. and Japan, the respective federal governments imposed increasingly strict
exhaust emission regulations. During that time period, the vast majority of gasoline-fueled automobile and
light truck engines did not use fuel injection. To comply with the new regulations, automobile manufacturers
often made extensive and complex modifications to the engine carburetor(s). While a simple carburetor
system is cheaper to manufacture than a fuel injection system, the more complex carburetor systems
installed on many engines in the 1970s were much more costly than the earlier simple carburetors. To more
easily comply with emissions regulations, automobile manufacturers began installing fuel injection systems
in more gasoline engines during the late 1970s.

Open-loop fuel injection systems had already improved cylinder-to-cylinder fuel distribution and engine
operation over a wide temperature range, but did not offer further scope to sufficiently control fuel/air
mixtures, in order to further reduce exhaust emissions. Later closed-loop fuel injection systems improved
the air–fuel mixture control with an exhaust gas oxygen sensor. Although not part of the injection control, a
catalytic converter further reduces exhaust emissions.

Fuel injection was phased in through the latter 1970s and 80s at an accelerating rate, with the German,
French, and U.S. markets leading and the UK and Commonwealth markets lagging somewhat. Since the
early 1990s, almost all gasoline passenger cars sold in first world markets are equipped with electronic fuel
injection (EFI). In Brazil, carburetors were entirely replaced by fuel injection during the 1990s, with the first
EFI equipped model built in 1989 (the Volkswagen Gol).[29] The carburetor remains in use in developing
countries where vehicle emissions are unregulated and diagnostic and repair infrastructure is sparse. Fuel
injection is gradually replacing carburetors in these nations too as they adopt emission regulations
conceptually similar to those in force in Europe, Japan, Australia, and North America.

Many motorcycles still use carburetored engines, though all current high-performance designs have
switched to EFI.

NASCAR finally replaced carburetors with fuel-injection, starting at the beginning of the 2012 NASCAR
Sprint Cup Series season.[30][31][32]

System components

System overview
The process of determining the necessary amount of fuel, and its delivery into the engine, are known as fuel
metering. Early injection systems used mechanical methods to meter fuel, while nearly all modern systems
use electronic metering.

Determining how much fuel to supply

The primary factor used in determining the amount of fuel required by the engine is the amount (by weight)
of air that is being taken in by the engine for use in combustion. Modern systems use a mass airflow sensor
to send this information to the engine control unit.

Data representing the amount of power output desired by the driver (sometimes known as "engine load") is
also used by the engine control unit in calculating the amount of fuel required. A throttle position sensor
(TPS) provides this information. Other engine sensors used in EFI systems include a coolant temperature
sensor, a camshaft or crankshaft position sensor (some systems get the position information from the
distributor), and an oxygen sensor which is installed in the exhaust system so that it can be used to
determine how well the fuel has been combusted, therefore allowing closed loop operation.

Supplying the fuel to the engine

Fuel is transported from the fuel tank (via fuel lines) and pressurised using fuel pump(s). Maintaining the
correct fuel pressure is done by a fuel pressure regulator. Often a fuel rail is used to divide the fuel supply
into the required number of cylinders. The fuel injector injects liquid fuel into the intake air (the location of
the fuel injector varies between systems).

Unlike carburetor-based systems, where the float chamber provides a reservoir, fuel injected systems depend
on an uninterrupted flow of fuel. To avoid fuel starvation when subject to lateral G-forces, vehicles are often
provided with an anti-surge vessel, usually integrated in the fuel tank, but sometimes as a separate, small
anti-surge tank.

EFI gasoline engine components

These examples specifically apply to a modern EFI gasoline engine. Parallels to fuels other
than gasoline can be made, but only conceptually.

Injectors
Fuel pump
Fuel pressure regulator
Engine control unit
Wiring harness
Various sensors (some of the sensors required are listed here)

Crank/cam position: Hall effect sensor


Airflow: MAF sensor, sometimes this is inferred with a MAP sensor
Exhaust gas oxygen: oxygen sensor, EGO sensor, UEGO sensor

Engine control unit


The engine control unit is central to an EFI
system. The ECU interprets data from input
sensors to, among other tasks, calculate the
appropriate amount of fuel to inject.

Fuel injector

When signaled by the engine control unit the


fuel injector opens and sprays the pressurised
fuel into the engine. The duration that the
injector is open (called the pulse width) is
proportional to the amount of fuel delivered.
Animated cut through diagram of a typical fuel injector. Click
Depending on the system design, the timing of to see animation.
when injector opens is either relative each
individual cylinder (for a sequential fuel
injection (SFI) system), or injectors for multiple cylinders may be signalled to open at the same time (in a
batch fire system).

Target air–fuel ratios


The relative proportions of air and fuel vary according to the type of fuel used and the performance
requirements (i.e. power, fuel economy, or exhaust emissions).

See Air–fuel ratio, Stoichiometry, and Combustion.

Various injection schemes

Single-point injection

Single-point injection (SPI) uses a single injector at the throttle body (the same location as was used by
carburetors).

It was introduced in the 1940s in large aircraft engines (then called the pressure carburetor) and in the 1980s
in the automotive world (called Throttle-body Injection by General Motors, Central Fuel Injection by Ford,
PGM-CARB by Honda, and EGI by Mazda). Since the fuel passes through the intake runners (like a
carburetor system), it is called a "wet manifold system".

The justification for single-point injection was low cost. Many of the carburetor's supporting components -
such as the air cleaner, intake manifold, and fuel line routing - could be reused. This postponed the redesign
and tooling costs of these components. Single-point injection was used extensively on American-made
passenger cars and light trucks during 1980–1995, and in some European cars in the early and mid-1990s.

Continuous injection

In a continuous injection system, fuel flows at all times from the fuel injectors, but at a variable flow rate.
This is in contrast to most fuel injection systems, which provide fuel during short pulses of varying duration,
with a constant rate of flow during each pulse. Continuous injection systems can be multi-point or single-
point, but not direct.
The most common automotive continuous injection system is Bosch's K-Jetronic, introduced in 1974. K-
Jetronic was used for many years between 1974 and the mid-1990s by BMW, Lamborghini, Ferrari,
Mercedes-Benz, Volkswagen, Ford, Porsche, Audi, Saab, DeLorean, and Volvo. Chrysler used a continuous
fuel injection system on the 1981-1983 Imperial.

In piston aircraft engines, continuous-flow fuel injection is the most common type. In contrast to automotive
fuel injection systems, aircraft continuous flow fuel injection is all mechanical, requiring no electricity to
operate. Two common types exist: the Bendix RSA system, and the TCM system. The Bendix system is a
direct descendant of the pressure carburetor. However, instead of having a discharge valve in the barrel, it
uses a flow divider mounted on top of the engine, which controls the discharge rate and evenly distributes
the fuel to stainless steel injection lines to the intake ports of each cylinder. The TCM system is even more
simple. It has no venturi, no pressure chambers, no diaphragms, and no discharge valve. The control unit is
fed by a constant-pressure fuel pump. The control unit simply uses a butterfly valve for the air, which is
linked by a mechanical linkage to a rotary valve for the fuel. Inside the control unit is another restriction,
which controls the fuel mixture. The pressure drop across the restrictions in the control unit controls the
amount of fuel flow, so that fuel flow is directly proportional to the pressure at the flow divider. In fact, most
aircraft that use the TCM fuel injection system feature a fuel flow gauge that is actually a pressure gauge
calibrated in gallons per hour or pounds per hour of fuel.

Central port injection

From 1992 to 1996 General Motors implemented a system called Central Port Injection or Central Port Fuel
Injection. The system uses tubes with poppet valves from a central injector to spray fuel at each intake port
rather than the central throttle-body. Fuel pressure is similar to a single-point injection system. CPFI (used
from 1992 to 1995) is a batch-fire system, while CSFI (from 1996) is a sequential system.[33]

Multipoint fuel injection

Multipoint fuel injection (MPI), also called port fuel injection (PFI), injects fuel into the intake ports just
upstream of each cylinder's intake valve, rather than at a central point within an intake manifold. MPI
systems can be sequential, in which injection is timed to coincide with each cylinder's intake stroke;
batched, in which fuel is injected to the cylinders in groups, without precise synchronization to any
particular cylinder's intake stroke; or simultaneous, in which fuel is injected at the same time to all the
cylinders. The intake is only slightly wet, and typical fuel pressure runs between 40-60 psi.

Many modern EFI systems use sequential MPI; however, in newer gasoline engines, direct injection systems
are beginning to replace sequential ones.

Direct injection

In a direct injection engine, fuel is injected into the combustion chamber as opposed to injection before the
intake valve (petrol engine) or a separate pre-combustion chamber (diesel engine).[34]

In a common rail system, the fuel from the fuel tank is supplied to the common header (called the
accumulator). This fuel is then sent through tubing to the injectors, which inject it into the combustion
chamber. The header has a high pressure relief valve to maintain the pressure in the header and return the
excess fuel to the fuel tank. The fuel is sprayed with the help of a nozzle that is opened and closed with a
needle valve, operated with a solenoid. When the solenoid is not activated, the spring forces the needle valve
into the nozzle passage and prevents the injection of fuel into the cylinder. The solenoid lifts the needle
valve from the valve seat, and fuel under pressure is sent in the engine cylinder. Third-generation common
rail diesels use piezoelectric injectors for increased precision, with fuel pressures up to 1,800 bar or
26,000 psi.

Direct fuel injection costs more than indirect injection systems: the injectors are exposed to more heat and
pressure, so more costly materials and higher-precision electronic management systems are required.

Diesel engines

All diesel engines have fuel injected into the combustion chamber.

Earlier systems, relying on simpler injectors, often injected into a sub-chamber shaped to swirl the
compressed air and improve combustion; this was known as indirect injection. However, this was less
efficient than the now common direct injection in which initiation of combustion takes place in a depression
(often toroidal) in the crown of the piston.

Throughout the early history of diesels, they were always fed by a mechanical pump with a small separate
chamber for each cylinder, feeding separate fuel lines and individual injectors. Most such pumps were in-
line, though some were rotary.

Most modern diesel engines use common rail or unit injector direct injection systems. A special type of
direct injection system is the M-System, that was used throughout the second half of the 20th century.

Gasoline engines

Modern gasoline engines also use direct injection, which is referred to as gasoline direct injection. This is
the next step in evolution from multi-point fuel injection, and offers another magnitude of emission control
by eliminating the "wet" portion of the induction system along the inlet tract.

By virtue of better dispersion and homogeneity of the directly injected fuel, the cylinder and piston are
cooled, thereby permitting higher compression ratios and earlier ignition timing, with resultant enhanced
power output. More precise management of the fuel injection event also enables better control of emissions.
Finally, the homogeneity of the fuel mixture allows for leaner air–fuel ratios, which together with more
precise ignition timing can improve fuel efficiency. Along with this, the engine can operate with stratified
(lean-burn) mixtures, and hence avoid throttling losses at low and part engine load. Some direct-injection
systems incorporate piezoelectronic fuel injectors. With their extremely fast response time, multiple
injection events can occur during each cycle of each cylinder of the engine.

Swirl injection

Swirl injectors are used in liquid rocket, gas turbine, and diesel engines to improve atomization and mixing
efficiency.

The circumferential velocity component is first generated as the propellant enters through helical or
tangential inlets producing a thin, swirling liquid sheet. A gas-filled hollow core is then formed along the
centerline inside the injector due to centrifugal force of the liquid sheet. Because of the presence of the gas
core, the discharge coefficient is generally low. In swirl injector, the spray cone angle is controlled by the
ratio of the circumferential velocity to the axial velocity and is generally wide compared with nonswirl
injectors.[35]

Maintenance hazards
Fuel injection introduces potential hazards in engine maintenance due to the high fuel pressures used.
Residual pressure can remain in the fuel lines long after an injection-equipped engine has been shut down.
This residual pressure must be relieved, and if it is done so by external bleed-off, the fuel must be safely
contained. If a high-pressure diesel fuel injector is removed from its seat and operated in open air, there is a
risk to the operator of injury by hypodermic jet-injection, even with only 100 psi (6.9 bar) pressure.[36] The
first known such injury occurred in 1937 during a diesel engine maintenance operation.[37]

Notes
1. Welshans, Terry (August 2013). "A Brief History of Aircraft Carburetors and Fuel Systems" (htt
p://www.enginehistory.org/Accessories/HxFuelSys/FuelSysHx01.shtml). enginehistory.org. US:
Aircraft Engine Historical Society. Retrieved 28 June 2016.
2. Hall, Carl W. (2008). A Biographical Dictionary of People in Engineering: From Earliest
Records to 2000 (1st ed.). Purdue University Press – via Credo Reference.
3. Hartmann, Gerard (5 August 2007). "Les moteurs et aéroplanes Antoinette" (https://web.archiv
e.org/web/20141214235209/http://www.hydroretro.net/etudegh/antoinette.pdf) [Antoinette
engines and aeroplanes] (PDF) (in French). hydroretro.net. Archived from the original (http://w
ww.hydroretro.net/etudegh/antoinette.pdf) (PDF) on 14 December 2014. Retrieved 1 May
2015.
4. Lindh, Björn-Eric (1992). Scania fordonshistoria 1891-1991 (in Swedish). Streiffert. ISBN 978-
91-7886-074-6.
5. Olsson, Christer (1990). Volvo – Lastbilarna igår och idag (in Swedish). Förlagshuset Norden.
ISBN 978-91-86442-76-7.
6. "The Direct Injection Engine Will Likely Power Your Next Car" (http://www.directinjectionengin
e.com). HybridKingdom.com. 2009. Retrieved 1 May 2015.
7. "1940 6C 2500 Touring "Ala Spessa" " (http://digilander.libero.it/spideralfaromeo/1940b.htm) (in
Italian). digilander.libero.it. Retrieved 20 January 2014.
8. Lindh, Björn-Eric (1992). Scania fordonshistoria 1891-1991 (Scania: vehicle history 1891-
1991) (in Swedish). Streiffert. ISBN 91-7886-074-1.
9. Olsson, Christer (1987). Volvo – Lastbilarna igår och idag (Volvo – the trucks yesterday and
today) (in Swedish). Norden. ISBN 91-86442-76-7.
10. Circle Track, 9/84, pp.82-3.
11. "A short history of Lucas injection" (http://www.lucasinjection.com/HISTORY.htm).
lucasinjection.com. Retrieved 1 May 2015.
12. "Petrol Injection Mk II" (http://www.lucasinjection.com/Lucas%20Mk2%20manual%20page%20
9.htm). Lucas Service Training Centre. Retrieved 1 May 2015.
13. Walton, Harry (March 1957). "How Good is Fuel Injection?" (https://books.google.com/books?i
d=byEDAAAAMBAJ&pg=PA88). Popular Science. 170 (3): 88–93. Retrieved 1 May 2015.
14. Davis, Marlan (October 2010). "What You Need To Know About Mechanical Fuel Injection" (htt
p://www.hotrod.com/techarticles/engine/hrdp_1010_what_you_need_to_know_about_mechani
cal_fuel_injection/index.html). Hot Rod Magazine. Retrieved 1 May 2015.
15. Faiz, Asif; Weaver, Christopher S.; Walsh, Michael P.; Gautam, Surhid P. (1996). Air pollution
from motor vehicles; standards and technologies for controlling emissions (https://books.googl
e.com/books?id=Hqsyv_KD0lgC&pg=PA113&dq=Electronic+vs+mechanical+fuel+injection).
The World Bank. p. 133. ISBN 9780821334447. Retrieved 26 August 2017.
16. "The Rambler Rebel's fuel injection – The Dream and the Legend" (https://www.hemmings.co
m/blog/2017/06/25/the-rambler-rebels-fuel-injection-the-dream-and-the-legend/). Hemmings.
27 June 2017. Retrieved 8 November 2018.
17. Ingraham, Joseph C. (24 March 1957). "Automobiles: Races; Everybody Manages to Win
Something At the Daytona Beach Contests" (http://select.nytimes.com/gst/abstract.html?res=F
60C16FD355A137A93C6AB1788D85F438585F9). The New York Times. p. 153. Retrieved
1 May 2015.
18. "1957 cars". Consumer Reports. 22: 154. 1957.
19. "1957 Rambler Rebel promotional flyers" (http://www3.ohio.net/~dsiringer/omcover/1950/195
7%20Rebel%20Flyer.JPG). ohio.net. Retrieved 8 November 2018.
20. Holder, William; Kunz, Phil (2006). Extreme Muscle Cars: The Factory Lightweight Legacy (htt
ps://books.google.com/books?id=Pn8cAHTaaKQC&pg=PA16). Krause Publications. p. 16.
ISBN 978-0-89689-278-1. Retrieved 1 May 2015.
21. "An Invitation to Happy Motoring... (Excerpts from the 1957 Rambler Rebel Owner's Manual)"
(https://web.archive.org/web/20021026224919/http://www.amxfiles.com/amc/rebel_57.html).
AMX-files.com. Archived from the original (http://www.amxfiles.com/amc/rebel_57.html) on 26
October 2002. Retrieved 8 November 2018.
22. Auto Editors of Consumer Guide (22 August 2007). "Rambler Measures Up" (http://auto.howst
uffworks.com/1957-1960-rambler-rebel2.htm). Retrieved 1 May 2015.
23. "1958 DeSoto Electrojector - First electronic fuel injection?" (https://www.allpar.com/cars/desot
o/electrojector.html). www.allpar.com. Retrieved 8 November 2018.
24. Aird, Forbes (2001). Bosch fuel injection systems. HP Trade. p. 29. ISBN 978-1-55788-365-0.
25. Kendall, Leslie. "American Musclecars: Power to the People" (https://web.archive.org/web/201
11027060937/http://www.petersen.org/default.cfm?docid=1034). Petersen Automotive
Museum. Archived from the original (http://www.petersen.org/default.cfm?docid=1034) on 27
October 2011. Retrieved 8 November 2018.
26. "Celica Parts Catalogue" (http://members.iinet.net.au/~stepho/manuals/Celica/JapSpecsCelica
1.tiff) (in Japanese). Toyota. Retrieved 20 January 2014.
27. 1975 Chevrolet Cosworth Vega Overhaul Supplement - general information
28. "A Timeline Overview of Motorola History 1928-2009" (https://web.archive.org/web/201106202
24820/http://www.motorola.com/staticfiles/Consumers/Corporate/US-EN/_Documents/Motorola
_History_Timeline.pdf) (PDF). Motorola. Archived from the original (http://www.motorola.com/st
aticfiles/Consumers/Corporate/US-EN/_Documents/Motorola_History_Timeline.pdf) (PDF) on
20 June 2011. Retrieved 20 January 2014.
29. "Grandes Brasileiros: Volkswagen Gol GTi completa 30 anos" (https://quatrorodas.abril.com.b
r/noticias/grandes-brasileiros-volkswagen-gol-gti-30-anos/). Quatro Rodas (in Portuguese).
Retrieved 11 June 2019.
30. Ryan, Nate (2 November 2011). "NASCAR sets fuel injection for '12 but keeping restrictor
plates" (https://www.usatoday.com/sports/motor/nascar/2011-02-11-nascar-fuel-injection_N.ht
m). USA Today. Retrieved 20 January 2014.
31. "NASCAR Moves to Fuel Injection, Bosch First Approved Supplier" (https://web.archive.org/we
b/20140201224457/http://www.autoserviceworld.com/news/nascar-moves-to-fuel-injection-bos
ch-first-approved-supplier/1000522267/). Auto Service World. 18 July 2011. Archived from the
original (http://www.autoserviceworld.com/news/nascar-moves-to-fuel-injection-bosch-first-appr
oved-supplier/1000522267/) on 1 February 2014. Retrieved 20 January 2014.
32. "Bosch to provide oxygen sensors for fuel injection" (https://web.archive.org/web/20111225011
421/http://www.nascar.com/news/111020/bosch-sensors-fuel-injection/index.html).
NASCAR.com. Archived from the original (http://www.nascar.com/news/111020/bosch-sensors
-fuel-injection/index.html) on 25 December 2011. Retrieved 20 January 2014.
33. 1997 Chevrolet Truck Service Manual, page 6A-24, drawing, item (3) Central Sequential
Muliport injector.
34. "IC Engines" (https://web.archive.org/web/20121006095155/http://www.unep.org/transport/gfei/
autotool/approaches/technology/ic_engines.asp#gasoline). Global Fuel Economy Initiative.
Archived from the original (http://www.unep.org/transport/gfei/autotool/approaches/technology/i
c_engines.asp) on 6 October 2012. Retrieved 1 May 2014.
35. Ji-Hyuk, Im; Seongho, Cho; Youngbin, Yoon; Insang, Moon (2010). "Comparative Study of
Spray Characteristics of Gas-Centered and Liquid-Centered Swirl Coaxial Injectors". Journal of
Propulsion and Power.
36. Agha, F.P. (1978). "High-pressure paint gun injuries of hand: clinical and roentgen aspects".
NY State Journal of Medicine. 78: 1955–6.
37. Rees, C.E. (1937). "Penetration of Tissue by Fuel Oil Under High Pressure from a Diesel
Engine". Journal of the American Medical Association. 109 (11): 866–7.
doi:10.1001/jama.1937.92780370004012c (https://doi.org/10.1001%2Fjama.1937.9278037000
4012c).

Further reading
Patents

U.S. Patent 3,430,616 (https://www.google.com/patents/US3430616) — Fuel Injection Control


System — Otto Glöckler, et al.
U.S. Patent 3,500,801 (https://www.google.com/patents/US3500801) — Actuator Circuit for
Electronic Precision Fuel Metering Systems — E. David Long and Keith C. Richardson
U.S. Patent 3,504,657 (https://www.google.com/patents/US3504657) — Cold Start Fuel
Enrichment — Dieter Eichler, et al.
U.S. Patent 3,548,791 (https://www.google.com/patents/US3548791) — Precision Fuel
Metering ... — E. David Long
U.S. Patent 4,069,795 (https://www.google.com/patents/US4069795) — Start-up Control for
Fuel Injection System — E. David Long and Keith C. Richardson

External links
History of the D Jetronic system (https://web.archive.org/web/20100809110201/http://member
s.rennlist.com/pbanders/djetfund.htm)
How Fuel Injection Systems Work (http://auto.howstuffworks.com/fuel-injection.htm)
Multi Point Fuel Injection System (MPFI) (https://www.enggstudy.com/2019/11/multi-point-fuel-i
njection-system-mpfi-working-pdf-ppt.html)

Retrieved from "https://en.wikipedia.org/w/index.php?title=Fuel_injection&oldid=952232190"

This page was last edited on 21 April 2020, at 05:43 (UTC).

Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply. By using this
site, you agree to the Terms of Use and Privacy Policy. Wikipedia® is a registered trademark of the Wikimedia
Foundation, Inc., a non-profit organization.

You might also like