Tech Data

ENDURATEX™ EP & ENDURATEX XL

SYNTHETIC BLEND GEAR OILS
Introduction
Petro-Canada Lubricants’ ENDURATEX™ EP • Protects against rust and corrosion
Gear Oils are premium quality, extreme-pressure
• Prevents iron parts from rusting
lubricants designed for use in enclosed
industrial gear drives operating under normal, • Protects copper-containing bearings,
heavy or shock-loaded conditions. They are What is the HT
bushings, etc., from corrosive attack
difference?
also recommended for lubricating plain or anti- • Extends equipment life
friction bearings running under heavy or shock- Petro-Canada
loaded conditions. • Water separability
Lubricants starts
ENDURATEX EP Gear Oils are specially • Prevents emulsion formation with the HT purity
formulated to deliver sustained long-life, anti- process to produce
• Allows water to be drained off before oil water-white, 99.9%
wear and extreme pressure protection to is re-circulated pure base oils.
industrial gear drives and bearings. These oils The result is a
• Eliminates corrosive damage to metal
are available in nine ISO viscosity grades and range of lubricants,
parts when water present
two multigrades. specialty fluids
• Low foaming tendency and greases that
Features
and Benefits • Ensures a continuous lubricant film deliver maximum
performance for
present at all times
• Exceptional long life our customers.
• Prevents overflow from gear-boxes and
• Reduces operating and maintenance
oil reservoirs
costs
• Reduces the possibility of cavitation
• Longer oil life helps extend time between
damage to oil circulating pumps where
oil changes
installed
• Withstands high operating temperatures
for longer periods Applications

• Reduces build-up of harmful sludge and
Petro-Canada Lubricants’ ENDURATEX EP
varnish deposits for reduced wear and
Gear Oils are versatile, high quality lubricants
longer oil life
recommended for use in all types of enclosed
industrial gear drives where an extreme
pressure gear oil is specified. They are also
recommended for lubricating all types of heavy
or shock-loaded bearings.
Protected by ENDURATEX EP Protected by competitor In addition, the low viscosity grades of
150 gear oil 150 gear oil ENDURATEX EP are effective wire-rope
lubricants.
ENDURATEX minimizes sludge and varnish deposits for
outstanding protection of gears and components ENDURATEX EP Oils offer excellent gear and
bearing protection and long service life in a
wide range of gear designs. These include:
• Excellent film strength and extreme
pressure properties for ENDURATEX EP • Spur, Internal, Planetary, Rack & Pinion,
equipment protection Bevel, Spiral-Bevel, Helical, Herringbone
and Worm gears
• Prevents seizure, scuffing or spalling of
gear teeth and bearing sur faces under
shock-loaded conditions
• Reduces gear and bearing wear
• Reduces maintenance costs and extends
equipment life

lubricants.petro-canada.com
ENDURATEX EP Gear Oils are approved by many For applications where no specific AGMA
manufacturers of industrial gear drives including: recommendation exists, the appropriate ENDURATEX
• ENDURATEX EP 68 has Metso Paper approval EP viscosity grade can be determined from the
and is recommended for pulp and paper following tables:
companies using thermo-mechanical pulping
processes (TMP) SPUR, BEVEL & HELICAL GEAR LUBRICATION

• ENDURATEX EP Gear Oils are approved ENDURATEX EP

according to Fives Cincinnati (formerly MAG IAS) TYPE OF UNIT/SIZE
-10ºC to +15ºC +10ºC to +50ºC
P-specifications: P-77 (EP 150), P-74 (EP 220), 14ºF to 62ºF 50ºF to 122ºF
P-59 (EP 320) and P-35 (EP 460).
Single/Double Reduction Units
ENDURATEX EP Gear Oils are also suitable for use in Parallel shaft separation:
applications by the following manufacturers: Greey- - up to 20 cm (8”) 68 100
Lightnin, Hansen Transmissions, Kraus-Maffei and - 20 to 50 cm (8” - 20”) 100 150
David Brown, as well as in situations requiring DIN - over 50 cm (20”) 150 220
51517 Part 3, ISO 12925 – Type 1 CKC or AGMA
Triple Reduction Units
9005-F-16 specifications.
Shaft separation:
- over 50 cm (20”) 220 320
ENDURATEX XL SYNTHETIC BLENDS
ENDURATEX XL Synthetic Blend are multigrade EP Planetary Gears
Outside housing diameter
gear oils designed with all the same benefits but
- up to 40 cm (16”) 68 150
with the additional advantage of eliminating seasonal - over 40 cm (16”) 150 220
change-outs- available in 68/150 and 68/220
grades. 68/150 delivers excellent low temperature Bevel, Spiral Bevel
properties versus leading all season competitive Cone distance
products for easier cold start-ups and better equipment - up to 30 cm (12”) 68 150
protection. 68/220 supports winter requirements - over 30 cm (12”) 150 220
(68 grade) and summer requirements (220 grade). - High speed, above 3600 rpm 68 68
68/220 is especially recommended for gearboxes Gearmotors
exposed to temperature extremes and has sufficient - all sizes 68 150
low temperature fluidity to perform well in exposed
locations - giving you extended drain intervals and WORM GEAR LUBRICATION
minimized downtime.
ENDURATEX EP
TYPE OF UNIT/SIZE
Enclosed Gear Lubrication -10ºC to +15ºC +10ºC to +50ºC
14ºF to 62ºF 50ºF to 122ºF
With enclosed gear drives, best results are obtained by
maintaining the correct oil level, i.e. the lowest teeth Low speed(below 600 rpm)
should be half submerged when at rest. - single enveloping 460 680
- double enveloping 680 680
The American Gear Manufacturers’ Association (AGMA)
has published several gear lubricant standards High speed(above 600 rpm)
for industrial machinery. ENDURATEX EP Oils are - single enveloping 320 460
recommended for use, where the AGMA specifies the - double enveloping 460 680
following EP type oils:
Where all-season protection is required for wide
VISC. RANGE temperature ranges, ENDURATEX XL Synthetic Blend
FORMER AGMA ENDURATEX EP multigrades are recommended.
cSt @
NUMBERS EP
40ºC/104ºF Temperature ranges noted are for normal gearbox
2 61.2 - 74.8 68 operating temperatures and do not represent the
3 90 - 110 100
operating limits of the product.
4 135 - 165 150 For gearboxes operating outside the listed temperature
5 198 - 242 220 ranges, please contact Petro-Canada Technical
6 288 - 352 320 Services for an appropriate recommendation.
7 414-506 460
8 612-748 680
8A 900-1100 1000
Typical Performance Data
XL SYNTHETIC
TEST ENDURATEX EP Oils BLEND
PROPERTY
METHOD 32 68 100 150 220 320 460 680 1000 68/150 68/220
Former AGMA Number - 2 3 4 5 6 7 8 8A 3 4
Density, kg/L @ 15°C/59°F ASTM D4052 0.847 0.864 0.872 0.882 0.890 0.899 0.903 0.912 0.902 0.868 0.870
Colour ASTM D1500 <1.0 <1.0 <1.0 2.5 3.0 4.0 <5.0 >8.0 <5.5 <1.0 1.0
Viscosity cSt @ 40°C ASTM D445 32.0 68.0 101 150 220 325 452 688 1077 98.2 152
cSt @ 100°C ASTM D445 6.0 9.1 11.3 15.0 19.4 25.2 30.4 34.5 55 14.3 22.2
Viscosity Index ASTM D2270 136 109 97 100 99 100 97 88 100 149 183
Flash Point, °C/°F ASTM D92 224/435 240/464 240/464 269/516 275/527 287/549 276/529 297/567 237/459 250/482 251/484
Pour Point, °C/°F ASTM D5950 -51/-60 -39/-38 -33/-27 -33/-27 -27/-17 -21/-6 -15/5 -9/16 -15/5 -39/-38 -33/-27
FDSTD791/
Channel Point,°C/°F -58/-72 -46/-51 -40/-40 -37/-35 -37/-35 -29/-20 -24/-11 -18/0 — -55/-67 -54/-65
D3456.2
Brookfield Viscosity 150,000
ASTM D2983 -47/-53 -33/-27 -29/-20 -26/-15 -18/0 -13/9 -13/9 -9/16 — -32/-26 -31/-24
cP Temperature, °C / °F
Timken EP Test, kg / lb ASTM D2782 27/60 30/65 32/70 32/70 32/70 32/70 32/70 32/70 34/75 32/70 32/70
Four-Ball Weld Load, kg ASTM D4172 250 250 250 250 250 250 250 250 315 250 250
Four-Ball Scar Diameter
mm, 1 hour, 20 kg / 44 lb, ASTM D2782 0.31 0.30 0.29 0.27 0.29 0.28 0.33 0.27 0.38 0.28 0.28
54°C / 129°F, 1800 rpm
Load Wear Index ASTM D2783 45 49 49 47 47 48 54 49 55 46 46
FZG Failure Load Stage DIN 51 354 Part 2 12+ 12+ 12+ 12+ 12+ 12+ 12+ 12+ 12+ 12+ 12+
Demulsibility Test
Water separated, mL ASTM D2711 85.0 86.3 86.0 85.6 83.4 83.0 82.0 82.0 — 76.0 74.5
Emulsion formed, mL 1.0 0.1 0.1 0.2 0.5 0.8 0.0 0.0 — 1.4 1.6
Foaming Characteristics
Vol. after blow/settling,
ASTM D892
24°C / 75°F 5/0 20/0 0/0 0/0 0/0 0/0 0/0 0/0 — 5/0 0/0
93.5°C / 200°F 0/0 40/0 0/0 0/0 0/0 0/0 0/0 0/0 — 0/0 5/0
Oxidation Stability
% Viscosity Increase ASTM D2893 3.7 2.7 3.7 3.8 4.9 7.3 7.9 7.9 — 3.5 3.5
312 hours, 121°C / 250°F
Rust Test Procedure B, 48 hrs ASTM D665 Pass Pass Pass Pass Pass Pass Pass Pass — Pass Pass
Copper Strip Corrosion Test,
ASTM D130 1a 1a 1a 1b 1b 1a 1b 1b 1a 1a 1a
3 hours @ 100°C / 212°F
The values quoted above are typical of normal production. They do not constitute a specification.
 To order product or to learn more about how Petro-Canada Lubricants
can help your business visit: lubricants.petro-canada.com
or contact us at: lubecsr@petrocanadalsp.com

IM-7810E (2019.02)
TM
Owned or used under license.