TBS175H user manual V1.

TBS175H
Forklift Authentication Device
Manual
Version 1.0

No:9 Jawahar Main Road,

P.Puliampatti 638459
Erode (Dt), India
techbiizindia@gmail.com

1
 TBS175H user manual V1.0

Contents

1 Profile ............................................................................................................... 1

2. System Installation .......................................................................................... 4

3. Connection with the peripheral devices ........................................................... 8

4. Basic operations ............................................................................................ 14

5. Communications ............................................................................................ 23

2
 TBS175H user manual V1.0

1 Profile

1.1 Basic function parameters

Features
Easy installation, high reliability
Simple and clear operation flow, voice prompts in the
operations. Support the ID / MF card, a wider use range.
Support the backup authentication, stronger function (also with the
extension function).

Basic function parameters are shown as follows:

Power DC12V
Function Access control device, has the
detection functions such as door
sensor, device dismantled etc.
One Wiegand output (only TBS175H)
User number 200 (fingerprint, ID card and MF
card)
Record memory 30000 records
communication USB
RS232/485 (device monitors the
running)
Fingerprint head Optical fingerprint head
Door bell Support the wired doorbell
Speaker The voice prompts
Buzzer Alarm when the device is dismantled
LED Indicate-Green

All copyrights are reserved -1-

3
 TBS175H user manual V1.0

Language Support multi-national voices

Sleep Support the sleep function
Water proof No

Explanation:
1. Access control function: support the access control output,
door sensor alarm, exit button, but not support time segment,
duress alarm etc. It is a comparatively simple access control.
2. Sleep function: during sleeping, the backlight of fingerprint
head is turned off and Led displays, if any key is pressed (except
the Bell key), it will be waked up automatically to work
normally.

4
 TBS175H user manual V1.0

Back panel:

Anti-dismantle button: Send

out the alarm signal through
the terminal when the device

Speaker (mainly used in voice prompt)

Bottom Panel

USB interface
Reset key
Press this key to restart device if
device can not run normally due to
the error operations or other
accidents.

5
 TBS175H user manual V1.0

2. System Installation

2.1 Installation Notices

Our products are mass-produced and in accordance with the strict
production and testing standards in China, the United States and the
European Union, but we hope you read the installation notices
carefully before the installation. The company to remind you the
proper use, will greatly improve your use effect and speed. If you don’t
read the notes
carefully before the installation, probably because of improper
installation will cause a very serious accident damage, even though
we make every effort to provide you with good service, and you will
have to pay an unnecessary price.
1. Please connect the power supply later after all other wires are
connected well. If the machine cannot run normally, please cut off the
power and then start examination. Please remember: All connection
wires with power will damage the machine accidentally. We won’t
provide maintenance for such damage.
2. Recommend the use of 3A/12V DC power supply to the equipment.
For details, consult the relevant technical staff.
3. Please firstly read explanations of connection terminals carefully
and then connect the wires in strict accordance with the rules, due to
abnormal operations may result in equipment damages, do not
belong to the scope of warranty
4. All external connection wires are forbidden to be bared, both
connections and useless ends of wires must be bandaged with
insulating tape to prevent the accident contact of bared wires, which
cause the machine damage.

6
 TBS175H user manual V1.0

5. To prevent excessive instantaneous electrostatic damage to

the machine in winter or the place with a comparatively serious
static, please connect the ground wire firstly, then connect the
other wires.
6. If the distance between power supply and machine is long,
please don't use the net cable or other types of lines to take place
of power cord. While selecting power cord, voltage attenuation
caused by overlong transmission distance should be taken into
account.
7. When use 485 to organize a network, please use the
professional
485 bus and RS232/485 transformer with power, and adopt the
bus-type wiring. If RS485 communication distance is over 300
meters, add a terminal matched resistor about 120Ω to the
RS485 bus.
8. Please use the access control software to connect the
machine and enroll users.

7
 TBS175H user manual V1.0

2.2 System Installation

1．When a person has passed the status authentication on the

access control device, the device will output the lock control
signal to unlock.
2. Sensor will detect & allow forklift to operate.
3. If the access control device is in unusual circumstances such as
illegal demolition etc., it will output the alarm signal (switch
volume signal).
4. External wired hooter can be connected.
5. Through RS485/RS232/USB to connect with PC and transfer
data to PC, you can easily manage multiple terminal devices
through access control management software.

8
 TBS175H user manual V1.0

3. Connection with the Forklift devices

3.1 Connection with access controller （only TBS175H）

TBS175H as a fingerprint reader, can support various Wiegand format
outputs, and can connect with access controllers of majority
manufacturers on the market. Wiegand output has two modes as follows:
The mode to output user number: Wiegand outputs the fingerprint or
the user number after a successful card authentication, or the
instruction code after a failed authentication.
The mode to output card: Wiegand outputs the got card data, that is,
to output the card data as the original.

Note: 1) The recommended distance between device and access controller

should not be more than 90 meters (If a longer distance or an environment
with interference, please use the Wiegand signal extender).
2) Regardless of whether the device shares power supply with the access
controller, the device must share the ground with the access controller to
guarantee the stability of Wiegand signal.
3) Since TBS175H and TBS175I can not be used as readers, RLED, GLED, BEEP
are the idle terminals. In addition, TBS175H has no Wiegand output, so 12V,
GND, WD0 and WD1 are also the idle terminals.

9
1. Device and lock share power supply

SF series

2. Device and lock do not share power supply

※Note: In case that device and lock don’t share power
supply: 1)ULOCK=12V and I-ILOCK≤1A;
2)ULOCK≠12V;
3) A long distance between device and lock.
(thereinto, ULOCK is the operate voltage of lock, I is the output current of
device’s power supply, ILOCK is the operate current of lock.)
（1）NC lock

SF series

DC Power

10
 TBS175H user manual V1.0

（2）NO lock
SF series
Normally open

11
 TBS175H user manual V1.0

3.3.1 Exit button

Exit button is a door-open switch installed inside the room and it is
closed to open the door. Please fix it at a place which is about 1.4
meter high from the ground. Please ensure its location is positive and
not askew, while its connection is accurate and firmly. (Cut off the
bared side of unused cable and wrap it with the insulating tape.) Please
pay attention to prevent the electromagnetic interference. (For
example: lighting switch, computer, etc)

3.3.2 Alarm
The alarm output of this fingerprint access control device is an on-off
signal. It can be put in series to the power circuit of a simple alarm. Of
course, it can also be used as a trigger signal of the advanced alarm or
the monitoring system. (The alarm output of the device only supports
the 12VDC alarm.)

3.3.3 Doorbell
The device can only use the doorbell with control pin. The doorbell
connected with power supply directly is not recommended.

12
 TBS175H user manual V1.0

3.4 Power supply

The device’s working power is DC12V. The working current is less than
300mA and the standby current is less than 200mA. Connect the
positive and negative poles of power supply between +12V and AGND
directly to work normally. (Don’t connect the positive and negative
poles in reverse.)

13
 TBS175H user manual V1.0

4. Basic operations
When power on, the device is in authenticating state. At this time the
user can enter into the states of user enrollment, administrator
enrollment, delete a user, and empty users. Each process is prompted
by the voice and the indicator light.

The operation processes are described as follows:

1. In authenticating state, if no enrolled fingerprint and card, the voice

‘Please press the Enroll key long to enroll a administrator’ prompts the
user to enroll a administrator as soon as possible.

2. User must enroll at least one administrator firstly before the normal
users can be enrolled.

3. During the enrollment, if no operation consecutively for n seconds

(set by the user), duplicate the corresponding voice prompt. After two
times consecutively voice prompts, system will return to the
authenticating status automatically. In the deletion state, system will
exit as soon as the first overtime

4. MF card can only support the same and simple functions of ID card
such as the enrollment and the deletion.

5. During the enrollment or the deletion, if consecutively three times

failed confirmations by the user, system will return to the
authenticating state with the prompt voice ‘A failed administrator
confirmation, system will return to the authenticating state’

6. During the enrollment or the deletion, if press the Enroll key or the

14
 TBS175H user manual V1.0

Delete key by the user, system will exit from the enrollment or the
deletion state automatically, and there are voice prompts.

7. During deleting a user, the last administrator can not be deleted.

8. During deleting a user, the administrator confirmation is not

required, but it is a must when delete all users.

9. When the enrolled fingerprints or cards are full, system will return to
the authenticating state with the prompt voice ‘Users are already full,
system exits!’.

10. There is a voice prompt when the records are full, and then the
later record can not be saved. At this time, users can mange the
records by connecting to the access control software.

11. Other Tips

a: In authenticating (verification)state, blue LED will flash once per
1/2 second. During enrollment and deletion, no flashed LED
displays.
b. If a successful authentication or enrollment or deletion, green led
will be constant on for a second; If a failed authentication or
enrollment or deletion, red LED will be constant on for a second.
c. When users open the door normally, 3 seconds after the lock is
locked up, if the device detects the door sensor has not been
closed well, the buzzer will work long to prompt; 1 minute later, if
the door sensor is still not closed well, the alarm will work.

15
 TBS175H user manual V1.0

5. Communications
The background PC software can communicate with the device through
three methods (RS232, RS485, USB), and then exchange the data. RS485
can also be used for the remote management.

USB communication

USB Cable

After device is connected with PC well, do the operations as

follows: Upload the user’s open door records
Upload and download the user information
Parameter setting, function configuration Device
monitors the running (only RS232/485)
The detail operation about data by the access control software, please
refer to <<access control software manual>>.

16
 TBS175H user manual V1.0

Statement on Human Rights and Privacy

Dear Customer:
First of all, Thank you for using the identification product designed
and produced by us. As the world famous provider of leading
identification technology, we attach great importance to the law
involved in human rights and privacy in every county.
Therefore, we have the following statements:
1. Our civilian identification equipment only capture character
points rather than images, not concerning in retaining privacy.
2. The captured character points cannot recover the original image,
not involved in privacy.
3. We (as provider of equipment) have no direct or indirect legal
liabilities for any negative consequences arising from using the
equipment.
4. If you have dispute about human rights or privacy, please
contact your employer.
Our other police equipment or development tools will provide
function to capture citizens’ original image. As for right infringement,
please contact government or the equipment’s ultimate provider. We
have no any legal liabilities for it.
1. The person is free from unlawful arrest, detention, search
and infringement.
2. Personal dignity related with personal freedom is out of
infringement.
3. Citizen’s residence is inviolable.
4. Citizen’s communication freedom and privacy are protected by law.
For password insecurity, people all over the world are suffering great

17
 TBS175H user manual V1.0

damages. The advanced identification technology will enter e-

commerce, bank, insurance, law affair and other industries in the near
future. Identification in high-security environment ensures you real
protection.

Environmental protection

The environmental protection use period marked on our products

is the safety period of our products used under the conditions
specified by this manual without toxic and harmful substances
leaking happened
The environmental protection use period marked on our products
does not include the easy wear and tear components required to
be replaced regularly such as the battery etc. The battery’s
environmental protection use period is 5 years.
The toxic and harmful substances or element names
and the content table
The toxic and harmful substances or elements
Part name Lead Merc Cadmiu Hexavalent Polybrominat Polybrominated
(Pb) ury m (Cd) Chromium ed biphenyls diphenyl ethers

(Hg) (Cr6 +) (PBB) (PBDE)

SMD × ○ ○ ○ ○ ○
resistor
SMD × ○ ○ ○ ○ ○
capacitor
SMD × ○ ○ ○ ○ ○
inductance
SMD diode × ○ ○ ○ ○ ○

18
 TBS175H user manual V1.0

ESD × ○ ○ ○ ○ ○
components
Buzzer × ○ ○ ○ ○ ○
Adapter × ○ ○ ○ ○ ○
Screw ○ ○ ○ × ○ ○
○：Indicate that the content of the toxic and harmful substance contained
in all homogeneous materials of this part is in the limitation requirement
stipulated in SJ / T 11363-2006.
×：Indicate the content of the toxic and harmful substance contained in at
least one homogeneous material of this part is beyond the limitation
requirement stipulated in SJ / T 11363-2006.
Note: The 80% product has adopted the manufacture with non-toxic and
harmless environmental protection materials, the non-toxic and harmless
substances or elements instead of the toxic and harmful substances or
elements contained can not be achieved because of the current
technology and economic constraints.

Imported & assembled by:

TechBiiz Solutions,
No:9 Jawahar Main Road,
P.Puliampatti 638459
Erode (Dt), India
Enquiry :
techbiizsolutions@gmail.com
Sales:
techbiizindia@gmail.com

All copyrights are reserved

19