Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
481 views4 pages

HPC Calculation Sheet

Uploaded by

fevahe756

1. Hydraulic calculations are presented for four locations along the Amarwada-Ramgarh Road project to determine the necessary pipe size for hydraulic culverts. 2. At each location, the peak discharge is calculated using Dickens and Ryves formulas based on the catchment area. 3. The maximum discharge value is used to determine that a 1000mm diameter NP4 hume pipe with a length of 12.5m is sufficient to pass flow at each location.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt

HPC Calculation Sheet

Uploaded by

fevahe756
481 views4 pages
1. Hydraulic calculations are presented for four locations along the Amarwada-Ramgarh Road project to determine the necessary pipe size for hydraulic culverts. 2. At each location, the peak discharge is calculated using Dickens and Ryves formulas based on the catchment area. 3. The maximum discharge value is used to determine that a 1000mm diameter NP4 hume pipe with a length of 12.5m is sufficient to pass flow at each location.

Original Description:

2

Copyright

© © All Rights Reserved

Available Formats

PDF, TXT or read online from Scribd

Did you find this document useful?

Is this content inappropriate?

1. Hydraulic calculations are presented for four locations along the Amarwada-Ramgarh Road project to determine the necessary pipe size for hydraulic culverts. 2. At each location, the peak discharge is calculated using Dickens and Ryves formulas based on the catchment area. 3. The maximum discharge value is used to determine that a 1000mm diameter NP4 hume pipe with a length of 12.5m is sufficient to pass flow at each location.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
481 views4 pages

HPC Calculation Sheet

Uploaded by

fevahe756
1. Hydraulic calculations are presented for four locations along the Amarwada-Ramgarh Road project to determine the necessary pipe size for hydraulic culverts. 2. At each location, the peak discharge is calculated using Dickens and Ryves formulas based on the catchment area. 3. The maximum discharge value is used to determine that a 1000mm diameter NP4 hume pipe with a length of 12.5m is sufficient to pass flow at each location.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 4

Sawytech Engineering Services Project Amarwada - Ramgarh Road

13, Yeswant Colony


Opp. Yeswant Club, Indore, Subject HPC at Km 0+917
E-mail:- sawytech@yahoo.co.in
Ph. No.: - +91-94253-15855 Element Hydraulic Calculations

Client :- E.E. M.P.P.W.D., Chhindwada Contractor M/s Rajaram Construction

Hydraulic Calculation
1 Chainage 0+917
2 Description of Catchment 0.08 sq. km.
3 Pipe Diameter Proposed 1 0 M.
1.0 M

Procedure Adopted

1 Discharge Calculation:-
a) Discharge from Dicken's Formula
3/4
Dicken's Discharge 'Q' = CM
Where,
3
Q = the peak run-off in m /s
(Clause 4.2 of IRC:SP:13-2004 ,C = 14-19 where
C= 14
the annual rain fall is more than 120 cm.)
M= 0.08 sq.km. (The area of catchment in sq.km)
3
Q = 2.11 m /s

b) Discharge from Ryve's Formula


2/3
Ryve's Discharge 'Q' = CM
Where,
3
Q = the peak run-off in m /s
(Clause 4.3 of IRC:SP:13-2004, C = 10.0
C= 10
for limited areas near the hills)
M= 0.08
0 08 sq.km.
sq km (The area of catchment in sq
sq.km)
km)
3
Q= 1.86 m /s

C) No. of pipe required

3
Max Discharge 2.11 M /sec (Adopt the Max. value of discharge from above two method)

Proposal 1 0 M Dia NP4 Hume Pipe is Prposed to Provide


1.0

Length of Pipe L= 12.5 M

3
Max discharge passing through pipe = 3.2X0.7853= 2.51 M /Sec

D) Hence provide one row of 1000 mm dia pipe is suffucient


Sawytech Engineering Services Project Amarwada - Ramgarh Road
13, Yeswant Colony
Opp. Yeswant Club, Indore, Subject HPC at Km 1+950
E-mail:- sawytech@yahoo.co.in
Ph. No.: - +91-94253-15855 Element Hydraulic Calculations

Client :- E.E. M.P.P.W.D., Chhindwada Contractor M/s Rajaram Construction

Hydraulic Calculation
1 Chainage 1+950
2 Description of Catchment 0.075 sq. km.
3 Pipe Diameter Proposed 1.0 M.

Procedure Adopted

1 Discharge Calculation:-
a) Discharge from Dicken's Formula
3/4
Dicken's Discharge 'Q' = CM
Where,
3
Q = the peak run-off in m /s
(Clause 4.2 of IRC:SP:13-2004 ,C = 14-19 where
C= 14
the annual rain fall is more than 120 cm.)
M= 0.075 sq.km. (The area of catchment in sq.km)
3
Q = 2.01 m /s

b) Discharge from Ryve's Formula


2/3
Ryve's Discharge 'Q' = CM
Where,
3
Q = the peak run-off in m /s
(Clause 4.3 of IRC:SP:13-2004, C = 10.0
C= 10
for limited areas near the hills)
M= 0.075 sq.km. (The area of catchment in sq.km)
3
Q= 1.78 m /s

C) No. of pipe required

3
Max Discharge 2.01 M /sec (Adopt the Max. value of discharge from above two method)

Proposal 1.0 M Dia NP4 Hume Pipe is Prposed to Provide

Length of Pipe L= 12.5 M

3
Max discharge passing through pipe = 3.0X0.7853= 2.35 M /Sec

D) Hence provide one row of 1000 mm dia pipe is suffucient


Sawytech Engineering Services Project Amarwada - Ramgarh Road
13, Yeswant Colony
Opp. Yeswant Club, Indore, Subject HPC at Km 2+2550
E-mail:- sawytech@yahoo.co.in
Ph. No.: - +91-94253-15855 Element Hydraulic Calculations

Client :- E.E. M.P.P.W.D., Chhindwada Contractor M/s Rajaram Construction

Hydraulic Calculation
1 Chainage 2+2250
2 Description of Catchment 0.085 sq. km.
3 Pipe Diameter Proposed 1.0 M.

Procedure Adopted

1 Discharge Calculation:-
a) Discharge from Dicken's Formula
3/4
Dicken's Discharge 'Q' = CM
Where,
3
Q = the peak run-off in m /s
(Clause 4.2 of IRC:SP:13-2004 ,C = 14-19
C= 14
where the annual rain fall is more than 120 cm.)
M= 0.085 sq.km. (The area of catchment in sq.km)
3
Q = 2.20 m /s

b) Discharge from Ryve's Formula


Ryve's Discharge 'Q' = CM2/3
Where,
3
Q = the peak run-off in m /s
(Clause 4.3 of IRC:SP:13-2004, C = 10.0
C= 10
for limited areas near the hills)
M= 0.085 sq.km. (The area of catchment in sq.km)
3
Q= 1.93 m /s

C) No. of pipe required

Max Discharge 2.20 M3/sec (Adopt the Max. value of discharge from above two method)

Proposal 1.0 M Dia NP4 Hume Pipe is Prposed to Provide

Length of Pipe L= 12.5 M

3
Max discharge passing through pipe = 3.3X0.7853= 2.60 M /Sec

D) Hence provide one row of 1000 mm dia pipe is suffucient


Sawytech Engineering Services Project Amarwada - Ramgarh Road
13, Yeswant Colony
Opp. Yeswant Club, Indore, Subject HPC at Km 4+150
E-mail:- sawytech@yahoo.co.in
Ph. No.: - +91-94253-15855 Element Hydraulic Calculations

Client :- E.E. M.P.P.W.D., Chhindwada Contractor M/s Rajaram Construction

Hydraulic Calculation
1 Chainage 4+150
2 Description of Catchment 0.087 sq. km.
3 Pipe Diameter Proposed 1.0 M.

Procedure Adopted

1 Discharge Calculation:-
a) Discharge from Dicken's Formula
3/4
Dicken's Discharge 'Q' = CM
Where,
3
Q = the peak run-off in m /s
(Clause 4.2 of IRC:SP:13-2004 ,C = 14-19 where
C= 14
the annual rain fall is more than 120 cm.)
M= 0.087 sq.km. (The area of catchment in sq.km)
3
Q = 2.24 m /s

b) Discharge from Ryve's Formula


2/3
Ryve's Discharge 'Q' = CM
Where,
3
Q = the peak run-off in m /s
(Clause 4.3 of IRC:SP:13-2004, C = 10.0
C= 10
for limited areas near the hills)
M= 0.087 sq.km. (The area of catchment in sq.km)
3
Q= 1.96 m /s

C) No. of pipe required

3
Max Discharge 2.24 M /sec (Adopt the Max. value of discharge from above two method)

Proposal 1.0 M Dia NP4 Hume Pipe is Prposed to Provide

Length of Pipe L= 12.5 M

3
Max discharge passing through pipe = 3.5X0.7853= 2.74 M /Sec

D) Hence provide one row of 1000 mm dia pipe is suffucient

You might also like