Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 463 views

    Welder Diameter Limitation ASME SEC IX

    Uploaded by

    kumar
    This document contains tables that specify welding qualification test requirements for groove and fillet welds of various diameters and thicknesses. Table QW-452.3 provides groove weld diameter limits based on the outside diameter of test coupons. Table QW-452.4 specifies minimum qualified diameters for small fillet welds based on test coupon diameters. Table QW-452.5 gives the type and number of tests required to qualify fillet welds of different thicknesses.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Welder Diameter Limitation ASME SEC IX

    Uploaded by

    kumar
    463 views1 page
    This document contains tables that specify welding qualification test requirements for groove and fillet welds of various diameters and thicknesses. Table QW-452.3 provides groove weld diameter limits based on the outside diameter of test coupons. Table QW-452.4 specifies minimum qualified diameters for small fillet welds based on test coupon diameters. Table QW-452.5 gives the type and number of tests required to qualify fillet welds of different thicknesses.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document contains tables that specify welding qualification test requirements for groove and fillet welds of various diameters and thicknesses. Table QW-452.3 provides groove weld diameter limits based on the outside diameter of test coupons. Table QW-452.4 specifies minimum qualified diameters for small fillet welds based on test coupon diameters. Table QW-452.5 gives the type and number of tests required to qualify fillet welds of different thicknesses.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    463 views1 page

    Welder Diameter Limitation ASME SEC IX

    Uploaded by

    kumar
    This document contains tables that specify welding qualification test requirements for groove and fillet welds of various diameters and thicknesses. Table QW-452.3 provides groove weld diameter limits based on the outside diameter of test coupons. Table QW-452.4 specifies minimum qualified diameters for small fillet welds based on test coupon diameters. Table QW-452.5 gives the type and number of tests required to qualify fillet welds of different thicknesses.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    ASME BPVC.

    IX-2017

    Table QW-452.3
    Groove-Weld Diameter Limits
    Outside Diameter Qualified,
    Outside Diameter of Test in. (mm)
    Coupon, in. (mm) Min. Max.
    Less than 1 (25) Size welded Unlimited
    1 (25) to 2 7/8 (73) 1 (25) Unlimited
    Over 2 7/8 (73) 2 7/8 (73) Unlimited

    GENERAL NOTES:
    (a) Type and number of tests required shall be in accordance with
    QW-452.1.
    (b) 2 7/8 in. (73 mm) O.D. is the equivalent of NPS 2 1/2 (DN 65).

    Table QW-452.4
    Small Diameter Fillet-Weld Test
    Qualified
    Outside Diameter of Test Coupon, Minimum Outside Diameter, Thick-
    in. (mm) Qualified, in. (mm) ness
    Less than 1 (25) Size welded All
    1 (25) to 2 7/8 (73) 1 (25) All
    Over 2 7/8 (73) 2 7/8 (73) All

    GENERAL NOTES:
    (a) Type and number of tests required shall be in accordance with Table QW-452.5.
    (b) 2 7/8 in. (73 mm) O.D. is considered the equivalent of NPS 2 1/2 (DN 65).

    Table QW-452.5
    Fillet-Weld Test
    Type and Number of Tests
    Thickness of Test Required [Figure QW-462.4(b) or
    Coupon as Welded, Figure QW-462.4(c)]
    Type of Joint in. (mm) Qualified Range Macro Fracture
    3
    Tee fillet [Figure /16 (5) or greater All base material thicknesses, fillet sizes, and 1 1
    QW-462.4(b)] diameters 2 7/8 (73) O.D. and over [Note (1)]

    Less than 3/16 (5) T to 2 T base material thickness, T maximum 1 1


    fillet size, and all diameters 2 7/8 (73) O.D.
    and over [Note (1)]

    GENERAL NOTE: Production assembly mockups may be substituted in accordance with QW-181.2.1. When production as-
    sembly mockups are used, range qualified shall be limited to the fillet sizes, base metal thicknesses, and configuration of
    the mockup.
    NOTES:
    (1) Test coupon prepared as shown in Figure QW-462.4(b) for plate or Figure QW-462.4(c) for pipe.
    (2) 2 7/8 in. (73 mm) O.D. is considered the equivalent of NPS 2 1/2 (DN 65). For smaller diameter qualifications, refer to Table
    QW-452.4 or Table QW-452.6.

    178

    You might also like