TLV2186 Precision, Rail-to-Rail Input and Output, 24-V, Zero-Drift Operational Amplifier

Product Order Technical Tools & Support &
Folder Now Documents Software Community
TLV2186
SBOS947 – JULY 2019
TLV2186 Precision, Rail-to-Rail Input and Output, 24-V, Zero-Drift Operational Amplifier
1 Features 3 Description
1• High precision: The TLV2186 is a low-power, 24-V, rail-to-rail input
and output zero-drift operational amplifier (op amp).
– Offset drift: 0.1 μV/°C The TLV2186 features only 10 µV of offset voltage
– Low offset voltage: 10 μV (typical) and 0.1 µV/°C of offset voltage drift over
• Low quiescent current: 90 µA temperature (typical). This device is a great choice for
precision instrumentation, signal measurement, and
• Excellent dynamic performance:
active filtering applications.
– Gain bandwidth: 750 kHz
Low quiescent current consumption (90 μA) makes
– Slew rate: 0.35 V/µs the TLV2186 an excellent option for power-sensitive
• Robust design: applications, such as battery-powered instrumentation
– RFI/EMI filtered inputs and portable systems.
• Rail-to-rail input/output Moreover, the high common-mode architecture along
• Supply range: 4.5 V to 24 V with low offset voltage allows for high-side current
shunt monitoring at the positive rail. This device also
2 Applications provides robust ESD protection during shipment,
handling, and assembly.
• Precision high-side current sensing
The device is specified for operation from –40°C to
• Bridge amplifier +125°C.
• Strain gauge
• Temperature measurement Device Information(1)
• Resistance temperature detector PART NUMBER PACKAGE BODY SIZE (NOM)
TLV2186 SOIC (8) 4.90 mm × 3.90 mm
• Weigh scale
• Thermal meter (1) For all available packages, see the package option addendum
at the end of the data sheet.
• Power supply
High-Side Current Shunt Monitor Application VOS vs Input Common Mode Voltage
RS 4
3
Input-referred Offset Voltage (µV)
6 V to 24 V
2
1
0
Microcontroller -1
Battery / -2
Power
TLV2186 ADC -3
Supply
+ 0 V to 5 V
-4
-5
-6
-12.5 -10 -7.5 -5 -2.5 0 2.5 5 7.5 10 12.5
Input Common-mode Voltage (V)
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TLV2186
SBOS947 – JULY 2019 www.ti.com
Table of Contents
1 Features .................................................................. 1 8 Application and Implementation ........................ 20
2 Applications ........................................................... 1 8.1 Application Information............................................ 20
3 Description ............................................................. 1 8.2 Typical Applications ................................................ 22
4 Revision History..................................................... 2 9 Power Supply Recommendations...................... 27
5 Pin Configuration and Functions ......................... 3 10 Layout................................................................... 28
6 Specifications......................................................... 4 10.1 Layout Guidelines ................................................. 28
6.1 Absolute Maximum Ratings ...................................... 4 10.2 Layout Example .................................................... 29
6.2 ESD Ratings.............................................................. 4 11 Device and Documentation Support ................. 30
6.3 Recommended Operating Conditions....................... 4 11.1 Device Support...................................................... 30
6.4 Thermal Information .................................................. 4 11.2 Documentation Support ........................................ 30
6.5 Electrical Characteristics........................................... 5 11.3 Receiving Notification of Documentation Updates 30
6.6 Typical Characteristics .............................................. 6 11.4 Community Resources.......................................... 31
7 Detailed Description ............................................ 14 11.5 Trademarks ........................................................... 31
7.1 Overview ................................................................. 14 11.6 Electrostatic Discharge Caution ............................ 31
7.2 Functional Block Diagram ....................................... 14 11.7 Glossary ................................................................ 31
7.3 Feature Description................................................. 15 12 Mechanical, Packaging, and Orderable
7.4 Device Functional Modes........................................ 19 Information ........................................................... 31
4 Revision History
DATE REVISION NOTES
July 2019 * Initial release
2 Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: TLV2186

TLV2186
www.ti.com SBOS947 – JULY 2019
5 Pin Configuration and Functions
D Package
8-Pin SOIC
Top View
OUT A 1 8 V+
±IN A 2 7 OUT B
+IN A 3 6 ±IN B
V± 4 5 +IN B
Not to scale
Pin Functions
PIN
I/O DESCRIPTION
NAME NO.
–IN A 2 I Inverting input channel A
+IN A 3 I Noninverting input channel A
–IN B 6 I Inverting input channel B
+IN B 5 I Noninverting input channel B
OUT A 1 O Output channel A
OUT B 7 O Output channel B
V– 4 — Negative supply
V+ 8 — Positive supply
Copyright © 2019, Texas Instruments Incorporated Submit Documentation Feedback 3

TLV2186
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN MAX UNIT
VS Supply voltage, VS = (V+) – (V–) 26 V
Input Common-mode (V–) –0.5 (V+) + 0.5

V
voltage Differential (V+) – (V–) + 0.2
(2)
Output short-circuit Continuous
TJ Operating junction temperature -40 150 °C
Tstg Storage temperature -65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Theseare stress ratings
only, which do not imply functional operation of the device at these or anyother conditions beyond those indicated under Recommended
OperatingConditions. Exposure to absolute-maximum-rated conditions for extended periods mayaffect device reliability.
(2) Short-circuit to ground, one amplifier per package.
6.2 ESD Ratings

VALUE UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) 4000
V(ESD) Electrostatic discharge V
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2) 1500
(1) JEDEC document JEP155 states that 500-V HBM allows safemanufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safemanufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN NOM MAX UNIT
Supply Single supply 4.5 24

VS
Voltage Dual supply ±2.25 ±12 V
TA Specified temperature –40 125 °C
6.4 Thermal Information

TLV2186
THERMAL METRIC (1) D (SOIC) UNIT
8 PINS
RθJA Junction-to-ambient thermal resistance 129.4 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 69.6 °C/W
RθJB Junction-to-board thermal resistance 72.8 °C/W
ΨJT Junction-to-top characterization parameter 20.8 °C/W
ΨJB Junction-to-board characterization parameter 72.0 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance N/A °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.

TLV2186
6.5 Electrical Characteristics

at TA = 25°C, VS = ±2.25V to ±12V, RL = 10 kΩ connected to VS / 2, VCM = VS / 2, and VOUT = VS / 2 (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
OFFSET VOLTAGE
VOS Input offset voltage ±10 ±250 μV
dVOS/dT Input offset voltage drift TA = –40°C to +125°C ±0.1 ±1.0 μV/°C
Power-supply rejection
PSRR TA = –40°C to +125°C ±0.05 ±1 μV/V
ratio
INPUT BIAS CURRENT
0.1 0.6
IB Input bias current TA = –40℃ to +85℃ 0.6 nA
TA = –40℃ to +125℃ 5
0.1 1.2
IOS Input offset current TA = –40℃ to +85℃ 1.2 nA
TA = –40℃ to +125℃ 2
NOISE
Input voltage noise f = 0.1 Hz to 10 Hz 110 nVRMS
eN Input voltage noise density f = 1 kHz 38 nV/√Hz
iN Input current noise f = 1 kHz 100 fA/√Hz
INPUT VOLTAGE
VCM Common-mode voltage (V–) – 0.2 (V+) + 0.2 V
(V–) – 0.1 < VCM < (V+) + 0.1 V, VS = ±2.25 V 108 126
TA = –40℃ to +125℃ VS = ±12 V 110 134
Common-mode rejection
CMRR dB
ratio VS = ±2.25 V 106 114
(V–) – 0.1 < VCM < (V+) + 0.1 V,
TA = –40℃ to +125℃ VS = ±12 V 106 120
FREQUENCY RESPONSE
GBW Gain-bandwidth product 750 kHz
SR Slew rate 1-V step, G = 1 0.35 V/μs
tS Settling time To 0.1%, 1-V step , G = 1 7.5 μs
Overload recovery time VIN × gain > VS 10 μs
INPUT CAPACITANCE
ZID Differential 100 || 5 MΩ || pF
ZICM Common-mode 50 || 2.5 GΩ || pF
OPEN-LOOP GAIN
(V–) + 0.3 V < VO < (V+) –
120 140
0.3 V, RL = 10 kΩ
(V–) + 0.3 V < VO < (V+) –
0.3 V, RL = 10 kΩ, TA = 120 134
–40°C to 125°C
AOL Open-loop voltage gain VS = ±12 V dB
(V–) + 0.65 V < VO < (V+) –
120 140
0.65 V, RL = 2 kΩ
(V–) + 0.65 V < VO < (V+) –
0.65 V, RL = 2 kΩ, TA = 120 134
–40°C to 125°C
OUTPUT
No load 5 20
Voltage output swing from RL = 10 kΩ 60 100

VO mV
both rails RL = 2 kΩ 340 500
RL = 10 kΩ, TA = –40℃ to +125℃ 90 115
ISC Short-circuit current ±20 mA
CLOAD Capacitive load drive See typical curves
Open-loop output
RO See typical curves
impedance
POWER SUPPLY
Quiescent current per 90 130

IQ VS = ±2.25 to ±12 V µA
amplifier TA = –40°C to 125°C 150

TLV2186
6.6 Typical Characteristics

Table 1. Typical Characteristic Graphs
DESCRIPTION FIGURE
Offset Voltage Distribution Figure 1
Offset Voltage Drift (-40°C to +125C°C) Figure 2
Input Bias Current Distribution Figure 3
Input Offset Current Distribution Figure 4
Offset Voltage vs Common-Mode Voltage Figure 5
Offset Voltage vs Supply Voltage Figure 6
Open-Loop Gain and Phase vs Frequency Figure 7
Closed-Loop Gain vs Frequency Figure 8
Input Bias Current and Offset Current vs Temperature Figure 9
Output Voltage Swing vs Output Current (Sourcing) Figure 10
Output Voltage Swing vs Output Current (Sinking) Figure 11
CMRR and PSRR vs Frequency Figure 12
CMRR vs Temperature Figure 13
PSRR vs Temperature Figure 14
0.1-Hz to 10-Hz Voltage Noise Figure 15
Input Voltage Noise Spectral Density vs Frequency Figure 16
THD+N vs Frequency Figure 17
THD+N vs Output Amplitude Figure 18
Quiescent Current vs Supply Voltage Figure 19
Quiescent Current vs Temperature Figure 20
Open-Loop Gain vs Temperature (10 kΩ) Figure 21
Open-Loop Gain vs Temperature (2 kΩ) Figure 22
Open-Loop Output Impedance vs Frequency Figure 23
Small-Signal Overshoot vs Capacitive Load (Gain = –1, 10-mV step) Figure 24
Small-Signal Overshoot vs Capacitive Load (Gain = 1, 10-mV step) Figure 25
No Phase Reversal Figure 26
Positive Overload Recovery Figure 27
Negative Overload Recovery Figure 28
Small-Signal Step Response (Gain = 1, 10-mV step) Figure 29
Small-Signal Step Response (Gain = –1, 10-mV step) Figure 30
Large-Signal Step Response (Gain = 1, 10-V step) Figure 31
Large-Signal Step Response (Gain = –1, 10-V step) Figure 32
Phase Margin vs Capacitive Load Figure 33
Settling Time (1-V Step, 0.1% Settling) Figure 34
Short Circuit Current vs Temperature Figure 35
Maximum Output Voltage vs Frequency Figure 36
EMIRR vs Frequency Figure 37
Channel Separation Figure 38

TLV2186
at TA = 25°C, VS = ±12 V, VCM = VS / 2, RL = 10 kΩ (unless otherwise noted)
50 30
45 27
40 24
35 21
Amplifiers (%)
Amplifiers (%)
30 18
25 15
20 12
15 9
10 6
5 3
0 0
-50 -40 -30 -20 -10 0 10 20 30 40 50 -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1
Input Offset Voltage (uV) Input Offset Voltage Drift (µV/qC)
Figure 1. Offset Voltage Distribution Figure 2. Offset Voltage Drift (-40°C to 125C°C)
50 80
45 72
40 64
35 56
Amplifiers (%)
Amplifiers (%)
30 48
25 40
20 32
15 24
10 16
5 8
0 0
-0.6
-0.5
-0.4
-0.3
-0.2
-0.1
0.1
0.2
0.3
0.4
0.5
0.6
-1200 -900 -600 -300 0 300 600 900 1200

Input Offset Current (pA)
Input Bias Current (nA)
Figure 3. Input Bias Current Distribution

Figure 4. Input Offset Current Distribution
4 5
3
Input-referred Offset Voltage (µV)
4
2
3
Offset Voltage (µV)
1
0
2
-1
1
-2
-3 0
-4
-1
-5
-6 -2
-12.5 -10 -7.5 -5 -2.5 0 2.5 5 7.5 10 12.5 4 6 8 10 12 14 16 18 20 22 24
Input Common-mode Voltage (V) Supply Voltage (V)
Figure 5. Offset Voltage vs Common-Mode Voltage Figure 6. Offset Voltage vs Supply Voltage

TLV2186

180 180 30
Gain G= 1
150 Phase 150 G= 1
20 G= 10
120 120
10
Gain (dB)
Gain (dB)
Phase (q)
90 90
60 60
0
30 30
-10
0 0
-30 -30 -20

10m 100m 1 10 100 1k 10k 100k 1M 10M 100 1k 10k 100k 1M 10M
Frequency (Hz) Frequency (Hz)
Figure 7. Open-Loop Gain and Phase vs Frequency Figure 8. Closed-Loop Gain vs Frequency
2.7 12
Ibn
2.4 10
Ibp
2.1 Ios 8
6
1.8
Output Voltage (V)
Input Current (nA)
4
1.5
2
1.2
0
0.9
-2
0.6
-4
-40qC
0.3 -6 25qC
0 85qC
-8
125qC
-0.3 -10
-40 -20 0 20 40 60 80 100 120 140 0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 25
Temperature (qC) Output Current (mA)
Figure 9. Input Bias Current and Offset Current vs Figure 10. Output Voltage Swing vs Output Current
Temperature (Sourcing)
12.5 160
-40qC PSRR
10 25qC 140 PSRR
7.5 85qC CMRR
125qC 120
Rejection Ratio (dB)
5
Output Voltage (V)
2.5 100
0 80
-2.5 60
-5
40
-7.5
-10 20
-12.5 0
0 3 6 9 12 15 18 21 24 27 100m 1 10 100 1k 10k 100k 1M 10M
Output Current (mA) Frequency (Hz)
Figure 11. Output Voltage Swing vs Output Current Figure 12. CMRR and PSRR vs Frequency
(Sinking)

TLV2186

150 170
Common-Mode Rejection Ratio (dB)
145
Power Supply Rejection Ratio (dB)

140 160
135
150
130
125
140
120
115 130
110
105 120
-40 -25 -10 5 20 35 50 65 80 95 110 125 -40 -25 -10 5 20 35 50 65 80 95 110 125
Temperature (qC) Temperature (qC)
Figure 13. CMRR vs Temperature Figure 14. PSRR vs Temperature

1000
Input Referred Voltage Noise (200 nV/div)
Voltage Noise Density (nV/—Hz)
100
10
Time (1 s/div) 100m 1 10 100 1k 10k 100k
Frequency (Hz)
Figure 15. 0.1-Hz to 10-Hz Voltage Noise Figure 16. Input Voltage Noise Spectral Density vs
Frequency
1 -40 1 -40
Noise (dB)
G= 1, RL = 10 k: G= 1, RL = 10 k:
Total Harmonic Distortion + Noise (dB)

Noise (%)
Noise ( )
G= 1, RL = 2 k: G= 1, RL = 2 k:
G= 1, RL = 10 k: G= 1, RL = 10 k:
0.1 G= 1, RL = 2 k: -60 G= 1, RL = 2 k:
0.1 -60
Total Harmonic Distortion
0.01 -80
0.01 -80
0.001 -100
0.0001 -120 0.001 -100

100 1k 10k 10m 100m 1 10
Frequency (Hz) Output Amplitude (VRMS)
Figure 17. THD+N vs Frequency Figure 18. THD+N vs Output Amplitude

TLV2186

100 110
VS = 4.5 V
90 VS = 24 V
80 100
Quiescent Current (µA)
Quiescent Current (µA)

70
60 90
VS Min = 4.5 V
50
40 80
30
20 70
10
0 60
0 2 4 6 8 10 12 14 16 18 20 22 24 -40 -25 -10 5 20 35 50 65 80 95 110 125
Supply Voltage (V) Temperature (qC)
Figure 19. Quiescent Current vs Supply Voltage Figure 20. Quiescent Current vs Temperature
180 180
Open-loop Gain (dB)
Open-loop Gain (dB)

160 160
140 140
120 120
-40 -25 -10 5 20 35 50 65 80 95 110 125 -40 -25 -10 5 20 35 50 65 80 95 110 125
Temperature (qC) Temperature (qC)
RL = 2 kΩ
Figure 21. Open-Loop Gain vs Temperature Figure 22. Open-Loop Gain vs Temperature
1000 40
RISO = 0 :
Open-Loop Output Impedance, ZO (:)
35 RISO = 25 :
100 RISO = 50 :
30
Overshoot ( )
10
25
20
1
15
0.1
10
0.01 5
10 100 1k 10k 100k 1M 10 100 1000
Frequency (Hz) Capactiance (pF)
Gain = –1, 10-mV step
Figure 23. Open-Loop Output Impedance vs Frequency Figure 24. Small-Signal Overshoot vs Capacitive Load

TLV2186

100
RISO = 0 : VIN (V)
RISO = 25 : VOUT (V)
80 RISO = 50 :
Voltage (5 V/div)
Overshoot ( )
60
40
20
0
10 100 1000 Time (100 Ps/div)
Capactiance (pF)
Gain = 1, 10-mV step
Figure 25. Small-Signal Overshoot vs Capacitive Load Figure 26. No Phase Reversal
VIN
VOUT
Voltage (5 V/div)
Voltage (5 V/div)
VIN
VOUT
Time (10 Ps/div) Time (10 Ps/div)
Figure 27. Positive Overload Recovery Figure 28. Negative Overload Recovery
VIN VIN
VOUT VOUT
Voltage (5 mV/div)
Voltage (5 mV/div)
Gain = 1, 10-mV step Gain = –1, 10-mV step
Figure 29. Small-Signal Step Response Figure 30. Small-Signal Step Response

TLV2186

VIN (V) VIN (V)
VOUT (V) VOUT (V)
Voltage (2 V/div)
Voltage (2 V/div)
Gain = 1, 10-V step Gain = –1, 10-V step
Figure 31. Large-Signal Step Response Figure 32. Large-Signal Step Response
65
Falling
60 Rising
55
50 Output (1 mV/div)
Phase Margin (q)
45
40
35
30
25
20
15
10 100 1000 Time (5 Ps/div)
CLOAD (pF)
1-V step, 0.1% settling
Figure 33. Phase Margin vs Capacitive Load Figure 34. Settling Time
32 30
31 Sinking VS = r12 V
Sourcing VS = r2.25 V
30 25
Short Circuit Current (mA)
29
Output Voltage (VPP)
28 20
27
26 15
25
24 10
23
22 5
21
20 0
-40 -20 0 20 40 60 80 100 120 1 10 100 1k 10k 100k 1M
Temperature (qC) Frequency (Hz)
Figure 35. Short Circuit Current vs Temperature Figure 36. Maximum Output Voltage vs Frequency

TLV2186

175 -60
150 -80
Channel Seperation (dB)

EMIRR IN+ (dB)
125 -100
100 -120
75 -140
50 -160
25 -180
10M 100M 1G 10G 1k 10k 100k 1M
Frequency (Hz) Frequency (Hz)
Figure 37. EMIRR vs Frequency Figure 38. Channel Separation

TLV2186
7 Detailed Description
7.1 Overview
The TLV2186 operational amplifier combines precision offset and drift with excellent overall performance, making
the device a great choice for a wide variety of precision applications. The precision offset drift of only 0.1 µV/°C
provides stability over the entire operating temperature range of –40°C to +125°C. In addition, this device offers
excellent linear performance with high CMRR, PSRR, and AOL. As with all amplifiers, applications with noisy or
high-impedance power supplies require decoupling capacitors close to the device pins. In most cases, 0.1-µF
capacitors are adequate. See the Layout Guidelines section for details and a layout example.
The TLV2186 is part of a family of zero-drift, MUX-friendly, rail-to-rail output operational amplifiers. This device
operates from 4.5 V to 24 V, is unity-gain stable, and is designed for a wide range of general-purpose and
precision applications. The zero-drift architecture provides ultra-low input offset voltage and near-zero input offset
voltage drift over temperature and time. This choice of architecture also offers outstanding ac performance, such
as ultra-low broadband noise, zero flicker noise, and outstanding distortion performance when operating below
the chopper frequency.
7.2 Functional Block Diagram

The Functional Block Diagram shows a representation of the proprietary TLV2186 architecture.
C2
Notch
CHOP1 GM1 CHOP2 Filter GM2 GM3
+IN 24-V OUT

Differential
±IN Front End
GM_FF
C1

TLV2186
7.3 Feature Description

The TLV2186 operational amplifier has several integrated features to help maintain a high level of precision
through a variety of applications. These include a rail-to-rail inputs, phase-reversal protection, input bias current
clock feedthrough, EMI rejection, electrical overstress protection and MUX-friendly Inputs.
7.3.1 Rail-to-Rail Inputs

Unlike many chopper amplifiers, the TLV2186 has rail-to-rail inputs that allow the input common-mode voltage to
not only reach, but exceed the supply voltages by 200 mV. This configuration simplifies power-supply
requirements by not requiring headroom over the input signal range.
The TLV2186 is specified for operation from 4.5 V to 24 V (±2.25 V to ±12 V) with rail-to-rail inputs. Many
specifications apply from –40°C to +125°C. Parameters that can exhibit significant variance with regard to
operating voltage or temperature are presented in the Typical Characteristics section.
7.3.2 Phase-Reversal Protection

The TLV2186 has internal phase-reversal protection. Some op amps exhibit a phase reversal when the input is
driven beyond the linear common-mode range. This condition is most often encountered in noninverting circuits
when the input is driven beyond the specified common-mode voltage range, causing the output to reverse into
the opposite rail. The TLV2186 input prevents phase reversal with excessive common-mode voltage. Instead, the
output limits into the appropriate rail. This performance is shown in Figure 39.
VIN (V)
VOUT (V)
Voltage (5 V/div)
Time (100 Ps/div)
Figure 39. No Phase Reversal
7.3.3 Input Bias Current Clock Feedthrough

Zero-drift amplifiers such as the TLV2186 use a switching architecture on the inputs to correct for the intrinsic
offset and drift of the amplifier. Charge injection from the integrated switches on the inputs can introduce short
transients in the input bias current of the amplifier. The extremely short duration of these pulses prevents the
pulses from amplifying, however the pulses may be coupled to the output of the amplifier through the feedback
network. The most effective method to prevent transients in the input bias current from producing additional noise
at the amplifier output is to use a low-pass filter, such as an RC network.

TLV2186
Feature Description (continued)

7.3.4 EMI Rejection
The TLV2186 uses integrated electromagnetic interference (EMI) filtering to reduce the effects of EMI
interference from sources such as wireless communications and densely-populated boards with a mix of analog
signal chain and digital components. EMI immunity can be improved with circuit design techniques; the TLV2186
benefits from these design improvements. Texas Instruments has developed the ability to accurately measure
and quantify the immunity of an operational amplifier over a broad frequency spectrum extending from 10 MHz to
6 GHz. Figure 40 shows the results of this testing on the TLV2186. Table 2 lists the EMIRR +IN values for the
TLV2186 at particular frequencies commonly encountered in real-world applications. Applications listed in
Table 2 may be centered on or operated near the particular frequency shown. Detailed information can also be
found in the EMI Rejection Ratio of Operational Amplifiers (SBOA128), available for download from www.ti.com.
175
150
EMIRR IN+ (dB)
125
100
75
50
25
10M 100M 1G 10G
Frequency (Hz)
Figure 40. EMIRR Testing
Table 2. TLV2186 EMIRR IN+ for Frequencies of Interest

FREQUENCY APPLICATION AND ALLOCATION EMIRR IN+
Mobile radio, mobile satellite, space operation, weather, radar, ultra-high frequency
400 MHz 48.4 dB
(UHF) applications
Global system for mobile communications (GSM) applications, radio
900 MHz communication, navigation, GPS (to 1.6 GHz), GSM, aeronautical mobile, UHF 52.8 dB
applications
GSM applications, mobile personal communications, broadband, satellite, L-band
1.8 GHz 69.1 dB
(1 GHz to 2 GHz)
802.11b, 802.11g, 802.11n, Bluetooth®, mobile personal communications,
2.4 GHz industrial, scientific and medical (ISM) radio band, amateur radio and satellite, S- 88.9 dB
band (2 GHz to 4 GHz)
3.6 GHz Radiolocation, aero communication and navigation, satellite, mobile, S-band 82.5 dB
802.11a, 802.11n, aero communication and navigation, mobile communication,
5 GHz 95.5 dB
space and satellite operation, C-band (4 GHz to 8 GHz)

TLV2186
The electromagnetic interference (EMI) rejection ratio, or EMIRR, describes the EMI immunity of operational
amplifiers. An adverse effect that is common to many op amps is a change in the offset voltage as a result of RF
signal rectification. An op amp that is more efficient at rejecting this change in offset as a result of EMI has a
higher EMIRR and is quantified by a decibel value. Measuring EMIRR can be performed in many ways, but this
section provides the EMIRR +IN, which specifically describes the EMIRR performance when the RF signal is
applied to the noninverting input pin of the op amp. In general, only the noninverting input is tested for EMIRR for
the following three reasons:
• Op amp input pins are known to be the most sensitive to EMI, and typically rectify RF signals better than the
supply or output pins.
• The noninverting and inverting op amp inputs have symmetrical physical layouts and exhibit nearly matching
EMIRR performance
• EMIRR is more simple to measure on noninverting pins than on other pins because the noninverting input
terminal can be isolated on a PCB. This isolation allows the RF signal to be applied directly to the
noninverting input terminal with no complex interactions from other components or connecting PCB traces.
High-frequency signals conducted or radiated to any pin of the operational amplifier may result in adverse
effects, as the amplifier would not have sufficient loop gain to correct for signals with spectral content outside the
bandwidth. Conducted or radiated EMI on inputs, power supply, or output may result in unexpected dc offsets,
transient voltages, or other unknown behavior. Take care to properly shield and isolate sensitive analog nodes
from noisy radio signals and digital clocks and interfaces.
The EMIRR +IN of the TLV2186 is plotted versus frequency as shown in Figure 40. The TLV2186 unity-gain
bandwidth is 750 kHz. EMIRR performance below this frequency denotes interfering signals that fall within the op
amp bandwidth.
7.3.4.1 EMIRR +IN Test Configuration

Figure 41 shows the circuit configuration for testing the EMIRR +IN. An RF source is connected to the op amp
noninverting input terminal using a transmission line. The op amp is configured in a unity-gain buffer topology
with the output connected to a low-pass filter (LPF) and a digital multimeter (DMM). A large impedance mismatch
at the op amp input causes a voltage reflection; however, this effect is characterized and accounted for when
determining the EMIRR IN+. The multimeter samples and measures the resulting DC offset voltage. The LPF
isolates the multimeter from residual RF signals that may interfere with multimeter accuracy.
Ambient temperature: 25Û&
V+
±
Low-Pass
50
Filter
+
RF Source Digital
V± Sample /
DC Bias: 0 V Multimeter
Averaging
Modulation: None (CW)
Frequency Sweep: 201 pt. Log Not shown: 0.1 µF and 10 µF supply decoupling
Figure 41. EMIRR +IN Test Configuration

TLV2186
7.3.5 Electrical Overstress

Designers often ask questions about the capability of an operational amplifier to withstand electrical overstress.
These questions tend to focus on the device inputs, but may involve the supply voltage pins or even the output
pin. Each of these different pin functions have electrical stress limits determined by the voltage breakdown
characteristics of the particular semiconductor fabrication process and specific circuits connected to the pin.
Additionally, internal electrostatic discharge (ESD) protection is built into these circuits to protect from accidental
ESD events both before and during product assembly.
Having a good understanding of this basic ESD circuitry and the relevance to an electrical overstress event is
helpful. See Figure 42 for an illustration of the ESD circuits contained in the TLV2186 (indicated by the dashed
line area). The ESD protection circuitry involves several current-steering diodes connected from the input and
output pins and routed back to the internal power-supply lines, where the diodes meet at an absorption device
internal to the operational amplifier. This protection circuitry is intended to remain inactive during normal circuit
operation.
An ESD event produces a short-duration, high-voltage pulse that is transformed into a short-duration, high-
current pulse while discharging through a semiconductor device. The ESD protection circuits are designed to
provide a current path around the operational amplifier core to prevent damage. The energy absorbed by the
protection circuitry is then dissipated as heat.
When an ESD voltage develops across two or more amplifier device pins, current flows through one or more
steering diodes. Depending on the path that the current takes, the absorption device may activate. The
absorption device has a trigger or threshold voltage that is greater than the normal operating voltage of the
TLV2186, but less than the device breakdown voltage level. When this threshold is exceeded, the absorption
device quickly activates and clamps the voltage across the supply rails to a safe level.
When the operational amplifier connects into a circuit, as shown in Figure 42, the ESD protection components
are intended to remain inactive, and do not become involved in the application circuit operation. However,
circumstances may arise where an applied voltage exceeds the operating voltage range of a given pin. If this
condition occurs, there is a risk that some internal ESD protection circuits may be biased on, and conduct
current. Any such current flow occurs through steering-diode paths and rarely involves the absorption device.
(2)
TVS
RF
V+
RI
IN ESD Current-
Steering Diodes
(3) Op Amp OUT
RS
+IN Core
Edge-Triggered ESD
Absorption Circuit RL
ID
(1)
VIN
V±
(2)
TVS
(1) VIN = (V+) + 500 mV

(2) TVS: 26 V > VTVSBR (min) > V+ ; where VTVSBR (min) is the minimum specified value for the transient voltage suppressor
breakdown voltage.
(3) Suggested value is approximately 5 kΩ in example overvoltage condition.
Figure 42. Equivalent Internal ESD Circuitry Relative to a Typical Circuit Application

TLV2186
Figure 42 shows a specific example where the input voltage (VIN) exceeds the positive supply voltage (V+) by
500 mV or more. Much of what happens in the circuit depends on the supply characteristics. If V+ can sink the
current, one of the upper input steering diodes conducts and directs current to +VS. Excessively high current
levels can flow with increasingly higher VIN. As a result, the data sheet specifications recommend that
applications limit the input current to 10 mA.
If the supply is not capable of sinking the current, VIN may begin sourcing current to the operational amplifier, and
then take over as the source of positive supply voltage. The danger in this case is that the voltage can rise to
levels that exceed the operational amplifier absolute maximum ratings.
Another common question involves what happens to the amplifier if an input signal is applied to the input while
the power supplies V+ or V– are at 0 V. Again, this question depends on the supply characteristic while at 0 V, or
at a level below the input signal amplitude. If the supplies appear as high impedance, then the operational
amplifier supply current may be supplied by the input source through the current-steering diodes. This state is not
a normal bias condition; the amplifier most likely does not operate normally. If the supplies are low impedance,
then the current through the steering diodes can become quite high. The current level depends on the ability of
the input source to deliver current, and any resistance in the input path.
If there is any uncertainty about the ability of the supply to absorb this current, external zener diodes must be
added to the supply pins, as shown in Figure 42. The zener voltage must be selected such that the diode does
not turn on during normal operation. However, the zener voltage must be low enough so that the zener diode
conducts if the supply pin begins to rise above the safe operating supply voltage level.
7.3.6 MUX-Friendly Inputs

The TLV2186 features a proprietary input stage design that allows an input differential voltage to be applied while
maintaining high input impedance. Typically, high-voltage CMOS or bipolar-junction input amplifiers feature
antiparallel diodes that protect input transistors from large VGS voltages that may exceed the semiconductor
process maximum and permanently damage the device. Large VGS voltages can be forced when applying a large
input step, switching between channels, or attempting to use the amplifier as a comparator.
The TLV2186 solves these problems with a switched-input technique that prevents large input bias currents
when large differential voltages are applied. This solves many issues seen in switched or multiplexed
applications, where large disruptions to RC filtering networks are caused by fast switching between large
potentials. The TLV2186 offers outstanding settling performance as a result of these design innovations and
built-in slew rate boost and wide bandwidth. The TLV2186 can also be used as a comparator. Differential and
common-mode Absolute Maximum Ratings still apply relative to the power supplies.
7.4 Device Functional Modes

The TLV2186 has a single functional mode, and is operational when the power-supply voltage is greater than 4.5
V (±2.25 V). The maximum power supply voltage for the TLV2186 is 24 V (±12 V).

TLV2186
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information

The TLV2186 operational amplifier combines precision offset and drift with excellent overall performance, making
the device ideal for many precision applications. The precision offset drift of only 0.1 µV/°C provides stability over
the entire temperature range. In addition, the device pairs excellent CMRR, PSRR, and AOL dc performance with
outstanding low-noise operation. As with all amplifiers, applications with noisy or high-impedance power supplies
require decoupling capacitors close to the device pins. In most cases, 0.1-µF capacitors are adequate.
The following application examples highlight only a few of the circuits where the TLV2186 can be used.
8.1.1 Basic Noise Calculations

Low-noise circuit design requires careful analysis of all noise sources. External noise sources can dominate in
many cases; consider the effect of source resistance on overall op amp noise performance. Total noise of the
circuit is the root-sum-square combination of all noise components.
The resistive portion of the source impedance produces thermal noise proportional to the square root of the
resistance. The source impedance is usually fixed; consequently, select the op amp and the feedback resistors
to minimize the respective contributions to the total noise.
Figure 43 illustrates both noninverting (A) and inverting (B) op amp circuit configurations with gain. In circuit
configurations with gain, the feedback network resistors also contribute noise. In general, the current noise of the
op amp reacts with the feedback resistors to create additional noise components. However, the extremely low
current noise of the TLV2186 means that the current noise contribution can be neglected.
The feedback resistor values can generally be chosen to make these noise sources negligible. Low impedance
feedback resistors load the output of the amplifier. The equations for total noise are shown for both
configurations.

TLV2186
Application Information (continued)
(A) Noise in Noninverting Gain Configuration Noise at the output is given as EO, where
R1 R2
'1 = l1 + p „ ¨:A5 ;2 + :A0 ;2 + kA41 æ42 o + :E0 „ 45 ;2 + lE0 „ d hp
41 „ 42 2
:1; > 84/5 ?
42 2
41 41 + 42
GND ±
:2; A5 = ¥4 „ G$ „ 6(-) „ 45 d h
EO 8
+ Thermal noise of RS
¾*V
RS
:3; A41 æ42 = ¨4 „ G$ „ 6(-) „ d h d h
41 „ 42 8
Thermal noise of R1 || R2
41 + 42 ¾*V
+
:4; G$ = 1.38065 „ 10F23 d h
VS ,
± Boltzmann Constant
-
Source
:5; 6(-) = 237.15 + 6(°%) >-? Temperature in kelvins
GND
(B) Noise in Inverting Gain Configuration Noise at the output is given as EO, where
R1 R2
:45 + 41 ; „ 42
'1 = l1 + p „ ¨:A0 ;2 + kA41 +45 æ42 o + FE0 „ H
2
:6; IG > 84/5 ?
42 2
45 + 41 45 + 41 + 42
RS ±
:45 + 41 ; „ 42
EO
:7; A41 +45 æ42 = ¨4 „ G$ „ 6(-) „ H I d h
+ 8
+
45 + 41 + 42 ¾*V Thermal noise of (R1 + RS) || R2
VS
d h
±
:8; G$ = 1.38065 „ 10F23
GND ,
Source Boltzmann Constant
-
GND :9; 6(-) = 237.15 + 6(°%) >-? Temperature in kelvins
Copyright © 2017, Texas Instruments Incorporated
(1) en is the voltage noise spectral density of the amplifier. For the TLV2186 series of operational amplifiers, en = 38 nV/
√Hz at 1 kHz.
(2) For additional resources on noise calculations visit TI Precision Labs.
Figure 43. Noise Calculation in Gain Configurations

TLV2186
8.2 Typical Applications

8.2.1 High-Side Current Sensing
RL
+
24 V IL
± Load Current
R1 R2
+ 24 V ±
± VO
R3
+ TLV2186
R1 = R3, R2 = R4 R4
Figure 44. High-Side Current Monitor
8.2.1.1 Design Requirements

A common systems requirement is to monitor the current being delivered to a load. Monitoring makes sure that
normal current levels are being maintained, and also provides an alert if an overcurrent condition occurs.
Fortunately, a relatively simple current monitor solution can be achieved using a precision rail-to-rail input/output
op amp such as the TLV2186. This device has an input common-mode voltage (VCM) range that extends 200 mV
beyond each power supply rail allowing for operation at the supply rail.
The TLV2186 is configured as a difference amplifier with a predetermined gain. The difference amplifier inputs
are connected across a sense resistor through which the load current flows. The sense resistor may be
connected to the high side or low side of the circuit through which the load current flows. Commonly, high-side
current sensing is applied and an applicable TLV2186 configuration is in Figure 44. Low-side current sensing
may be applied as well if the sense resistor can be placed between the load and ground.
Use the following parameters for this design example:
• Single supply: 24 V
• Linear output voltage range: 0.3 V to 3.3 V
• Iload: 1 A to 11 A
The design details and equations below can be used to reconfigure this design for different output voltage ranges
and current loads.
8.2.1.2 Detailed Design Procedure

Designing a high-side current monitor circuit is straightforward providing the amplifier electrical characteristics are
carefully consideration so that linear operation is maintained. Other additional considerations, such as the input
voltage range of the analog to digital converter (ADC) that follows the current monitor stage, must be kept in
mind while configuring the system.
Consider the design of a TLV2186 high-side current monitor with an output voltage range set to be compatible
with the input of ADC with an input range of 3.3 V, such as one integrated in a microcontroller. The full-scale
input range of such a converter is 0 V to 3.3 V. The TLV2186 can be operated from a single 24-V supply,
referenced to ground. Although the TLV2186 is specified as a rail-to-rail input/output (RRIO) amplifier, the linear
output operating range (like all amplifiers) does not quite extend all the way to the supply rails. This linear
operating range must be taken into consideration.

TLV2186
Typical Applications (continued)

The TLV2186 is powered by 24 V; therefore, the device is easily capable of providing the 3.3-V positive level, or
even more if the ADC has a wider input range. However, because the TLV2186 output does not swing
completely to 0 V, the specified lower swing limit must be observed in the design.
The best measure of an op amp linear output voltage range comes from the open-loop voltage gain (AOL)
specification listed in the Electrical Characteristics table. The AOL test conditions specify a linear swing range 300
mV from each supply rail (RL = 10 kΩ). Therefore, the linear swing limit on the low end (VoMIN) is 300 mV, and
3.3 V is the VoMAX limit, thus yielding an 11:1 VoMAX to VoMIN ratio. This ratio proves important in determining the
difference amplifier operating parameters.
An optimum load current, ILOAD of 10 A is used as an example. In most applications, however, the ability to
monitor current levels well below 10 A is useful. This situation is where the 11:1 VoMAX to VoMIN ratio is crucial. If
11 A is set as the maximum current, this current must correspond to a 3.3-V output. Using the 11:1 ratio, the
minimum current of 1 A corresponds to 300 mV.
Selection of the current sense resistor RS comes down to how much voltage drop can be tolerated at maximum
current and the permissible power loss, or dissipation. A good compromise for a 10-A sense application is an RS
of 10 mΩ. That value results in a power dissipation of 1 W, and a 0.1-V drop at 10 amps.
Next, determine the gain of the TLV2186 difference amplifier circuit. The maximum current of 11 A flowing
through a 10-mΩ sense resistor results in 110 mV across the resistor. That voltage appears as a differential
voltage, VR, that is applied across the TLV2186 difference amplifier circuit inputs:
VS IL * RS
VS 11 A * 10 m : 110 mV (1)
The TLV2186 required voltage gain is determined from:
VOMAX
GA
VS
3.3 V V
GA 30
0.11 V V (2)
Now, checking the VoMIN using IL = 1 A:
VOMIN GA * ISMIN * RS
V
VOMIN 30 * 1 A * 10 m: 300 mV
V (3)
The complete TLV2186 high-side current monitor is shown in Figure 45. The circuit is capable of monitoring a
current range of < 1 A to 11 A, with a VCM very close to the 24-V supply voltage.
RL = 10 m
+ IL
24 V Load Current
± 1 A to 11 A
R1 = 1 k R2 = 30 k
+ 24 V ± + 3.3 V ±
±
R3 = 1 k µController
ADC
+ TLV2186
R4 = 30 k VO = 300 mV to 3.3 V
Figure 45. TLV2186 Configured as a High-Side Current Monitor

TLV2186

In this example, the TLV2186 output voltage is intentionally limited to 3.3 V. However, because of the 24-V
supply, the output voltage could be much higher to allow for a higher-voltage data converter with a higher
dynamic range.
The circuit in Figure 45 was checked using the TINA Spice circuit simulation tool to verify the correct operation of
the TLV2186 high-side current monitor. The simulation results are seen in Figure 46. The performance is exactly
as expected. Upon careful inspection of the plots, one possible surprise is that VO continues towards zero as the
sense current drops below 1 A, where VO is 300 mV and less.
VLOAD
RL = 10 m
+ IL
24 V Load Current
± 0 A to 11 A
R1 = 1 k R2 = 30 k
+ 24 V ±
VO = 0 V to 3.3 V
100 nF
±
R3 = 1 k
+ TLV2186
RL = 10 k
R4 = 30 k
Figure 46. TLV2186 High-Side Current-Monitor Simulation Schematic
The TLV2186 output, as well as other CMOS output amplifiers, often swing closer to 0 V than the linear output
parameters suggest. The Electrical Characteristics table lists under the OUTPUT subsection VO, which is an
output slam to the rail measure. It is not an indication of the linear output range, but instead how close the output
can move towards the supply rail. In that region, the amplifier output approaches saturation, and the amplifier
ceases to operate linearly. Thus, in the current-monitor application, the current-measurement capability may
continue well below the 300 mV output level. However, keep in mind that the linearity errors are becoming large.
Lastly, some notes about maximizing the high-side current monitor performance:
• All resistor values are critical for accurate gain results. The resistor pairs of [R1 and R3] and [R2 and R4]
must be matched as closely as possible to minimize common-mode mismatch error. Use a 0.1% tolerance, or
better. Often, selecting two adjacent resistors on a reel provides close matching compared to random
selection.
• Keep the closed-loop gain, GA, to which the TLV2186 difference amplifier is set, to a reasonable value. Doing
so reduces gain error and can be used to maximize bandwidth. A GA of 30 V/V is used in the example.
• Although current monitoring is often used for monitoring dc supply currents, ac current can also be monitored.
The –3-dB bandwidth, or upper cutoff frequency, of the circuit of is:
GBW
fH
Noise Gain
where
• GBW is the amplifier unity gain bandwidth; 750 kHz for the TLV2186.
• Noise gain is equal to the gain as seen looking into the op amp noninverting input, as shown in Equation 5. (4)
R2
GNG 1
R1 (5)

TLV2186

For the TLV2186 circuit in Figure 45:
30 k: V
GNG 1 31
1 k: V
750 kHz
fH 24.2 kHz
31
Make sure that the amplifier slew rate is sufficient to support the expected output voltage swing range and
waveform. Also, if a single power supply such as 24 V is used, the ac power source applied to the sense input
must have a positive dc component to keep the VCM above 0 V. The input voltage cannot drop below 0 V if
normal operation is to be maintained.
The TLV2186 output can attain a 0 V output level if a small negative voltage is used to power the V– pin instead
of ground. The LM7705 is a switched capacitor voltage inverter with a regulated, low-noise, –0.23-V fixed voltage
output. Powering the TLV2186 V– pin at this level approximately matches the 300-mV linear output voltage swing
lower limit, thus extending the output swing to 0 V, or very near 0 V. Doing so greatly improves the resolution at
low sense current levels.
The LM7705 requires only about 78 μA of quiescent current, but be aware that the specified supply range is 3 V
to 5.25 V. The 3.3-V or 5-V supply used by the ADC could be tapped as a power source.
For more information about amplifier-based, high-side current monitors, see the TI Analog Engineer’s Circuit
Cookbook: Amplifiers.
8.2.1.3 Application Curve

4 24.2
VOUT
3.6 VLOAD 24.16
3.2 24.12
2.8 24.08
Output Voltage (V)
Load Voltage (V)

2.4 24.04
2 24
1.6 23.96
1.2 23.92
0.8 23.88
0.4 23.84
0 23.8
0 1 2 3 4 5 6 7 8 9 10 11
Input Current (A)
Figure 47. High-Side Results

TLV2186

8.2.2 Bridge Amplifier
Figure 48 shows the basic configuration for a bridge amplifier. Click the following link to download the TINA-TI
file: Bridge Amplifier Circuit.
VEX
R1
R R
+5V
VOUT
R R
VREF
Figure 48. Bridge Amplifier
8.2.3 Low-Side Current Monitor

Figure 49 shows the TLV2186 configured in a low-side current-sensing application. The load current (ILOAD)
creates a voltage drop across the shunt resistor (RSHUNT). This voltage is amplified by the TLV2186, with a gain
of 201. In this example, the load current is set from 0 A to 500 mA, and corresponds to an output voltage range
from 0 V to 10 V. The output range can be adjusted by changing the shunt resistor or gain of the configuration.
Click the following link to download the TINA-TI file: Current-Sensing Circuit.
VSYSTEM
Load
15 V
+
VOUT = ILOAD * RSHUNT(1 + RF / RIN)
TLV2186 VOUT
ILOAD RSHUNT ± VOUT / ILOAD= 1 V / 49.75 mA
100 m
RIN RF
100 20 k
CF
150 pF
Figure 49. Low-Side Current Monitor

TLV2186

8.2.4 RTD Amplifier With Linearization
See the Analog Linearization of Resistance Temperature Detectors technical brief for an in-depth analysis of
Figure 50. Click the following link to download the TINA-TI file: RTD Amplifier with Linearization.
15 V
(5 V) Out In
REF5050
1 …F 1 …F
R2
49.1 kŸ
R3
60.4 kŸ
R1
4.99 kŸ
0°C = 0 V
TLV2186 V OUT
200°C = 5 V
R5
(1)
105.8 kŸ
RTD
Pt100 R4
1 kŸ
(1) R5 provides positive-varying excitation to linearize output.
Figure 50. RTD Amplifier With Linearization
9 Power Supply Recommendations

The TLV2186 is specified for operation from 4.5 V to 24 V (±2.25 V to ±12 V); many specifications apply from
–40°C to +125°C. The Typical Characteristics presents parameters that can exhibit significant variance with
regard to operating voltage or temperature.
CAUTION
Supply voltages larger than 40 V can permanently damage the device (see the
Absolute Maximum Ratings).
Place 0.1-μF bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or
high-impedance power supplies. For more detailed information on bypass capacitor placement, see the Layout
section.

TLV2186
10 Layout
10.1 Layout Guidelines

For best operational performance of the device, use good PCB layout practices, including:
• For the lowest offset voltage, avoid temperature gradients that create thermoelectric (Seebeck) effects in the
thermocouple junctions formed from connecting dissimilar conductors. Also:
– Use low thermoelectric-coefficient conditions (avoid dissimilar metals).
– Thermally isolate components from power supplies or other heat sources.
– Shield operational amplifier and input circuitry from air currents, such as cooling fans.
• Noise can propagate into analog circuitry through the power pins of the circuit as a whole and the op amp
itself. Bypass capacitors reduce the coupled noise by providing low-impedance power sources local to the
analog circuitry.
– Connect low-ESR, 0.1-µF ceramic bypass capacitors between each supply pin and ground, placed as
close as possible to the device. A single bypass capacitor from V+ to ground is applicable for single-
supply applications.
• Separate grounding for analog and digital portions of circuitry is one of the simplest and most effective
methods of noise suppression. One or more layers on multilayer PCBs are usually devoted to ground planes.
A ground plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digital
and analog grounds paying attention to the flow of the ground current. For more detailed information, seeThe
PCB is a component of op amp design.
• To reduce parasitic coupling, run the input traces as far away as possible from the supply or output traces. If
these traces cannot be kept separate, crossing the sensitive trace perpendicular is much better as opposed to
in parallel with the noisy trace.
• Place the external components as close as possible to the device. As illustrated in Figure 51, keep the
feedback resistor (R3) and gain resistor (R4) close to the inverting input to minimize parasitic capacitance.
• Keep the length of input traces as short as possible. Always remember that the input traces are the most
sensitive part of the circuit.
• Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduce
leakage currents from nearby traces that are at different potentials.
• For best performance, clean the PCB following board assembly.
• Any precision integrated circuit may experience performance shifts due to moisture ingress into the plastic
package. Following any aqueous PCB cleaning process, bake the PCB assembly to remove moisture
introduced into the device packaging during the cleaning process. A low-temperature, post-cleaning bake at
85°C for 30 minutes is sufficient for most circumstances.

TLV2186
10.2 Layout Example

Place bypass
capacitors as close to
device as possible
Use ground pours for (avoid use of vias)
GND
shielding the input C3 C4
+V signal pairs
R3 C3
R3
IN±
C4 1 NC NC 8 +V
1 NC NC 8
R1 R1
IN± 2 ±IN ± V+ 7 2 ±IN V+ 7
IN+ 3 +IN + OUT 6 OUT 3 +IN OUT 6 OUT

R2 R2
-V 4 V± NC 5
4 V± NC 5
C1
R4 IN+
GND
R4 -V
C2
Place components C1 Use a low-
close to device and to ESR,ceramic bypass
each other to reduce capacitor
parasitic errors C2
Figure 51. Operational Amplifier Board Layout for Difference Amplifier Configuration

TLV2186
11 Device and Documentation Support
11.1 Device Support

11.1.1 Development Support
11.1.1.1 TINA-TI™ (Free Software Download)

TINA-TI™ is a simple, powerful, and easy-to-use circuit simulation program based on a SPICE engine. TINA-
TI™ is a free, fully-functional version of the TINA™ software, preloaded with a library of macromodels in addition
to a range of both passive and active models. TINA-TI™ provides all the conventional dc, transient, and
frequency domain analysis of SPICE, as well as additional design capabilities.
Available as a free download from the Analog eLab Design Center, TINA-TI™ offers extensive post-processing
capability that allows users to format results in a variety of ways. Virtual instruments offer the ability to select
input waveforms and probe circuit nodes, voltages, and waveforms, creating a dynamic quick-start tool.
NOTE
These files require that either the TINA software (from DesignSoft™) or TINA-TI™
software be installed. Download the free TINA-TI™ software from the TINA-TI™ folder.
11.1.1.2 TI Precision Designs

TI Precision Designs are available online at http://www.ti.com/ww/en/analog/precision-designs/. TI Precision
Designs are analog solutions created by TI’s precision analog applications experts and offer the theory of
operation, component selection, simulation, complete PCB schematic and layout, bill of materials, and measured
performance of many useful circuits.
11.2 Documentation Support

11.2.1 Related Documentation
For related documentation see the following:
• Texas Instruments, Zero-drift Amplifiers: Features and Benefits
• Texas Instruments, The PCB is a component of op amp design
• Texas Instruments, Op Amps for Everyone
• Texas Instruments, Operational amplifier gain stability, Part 3: AC gain-error analysis
• Texas Instruments, Operational amplifier gain stability, Part 2: DC gain-error analysis
• Texas Instruments, Using infinite-gain, MFB filter topology in fully differential active filters
• Texas Instruments, Op Amp Performance Analysis
• Texas Instruments, Single-Supply Operation of Operational Amplifiers
• Texas Instruments, Tuning in Amplifiers
• Texas Instruments, Shelf-Life Evaluation of Lead-Free Component Finishes
• Texas Instruments, Feedback Plots Define Op Amp AC Performance
• Texas Instruments, EMI Rejection Ratio of Operational Amplifiers
• Texas Instruments, Analog Linearization of Resistance Temperature Detectors
• Texas Instruments, TI Precision Design TIPD102 High-Side Voltage-to-Current (V-I) Converter
11.3 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.

TLV2186
11.4 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.5 Trademarks
TINA-TI, E2E are trademarks of Texas Instruments.
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
TINA, DesignSoft are trademarks of DesignSoft, Inc.
All other trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM
www.ti.com 6-Feb-2020
PACKAGING INFORMATION
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
TLV2186IDR ACTIVE SOIC D 8 2500 Green (RoHS NIPDAU Level-2-260C-1 YEAR -40 to 125 T2186
& no Sb/Br)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 11-Mar-2020
TAPE AND REEL INFORMATION
*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TLV2186IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 11-Mar-2020
*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TLV2186IDR SOIC D 8 2500 367.0 367.0 35.0
Pack Materials-Page 2
PACKAGE OUTLINE
D0008A SCALE 2.800
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A PIN 1 ID AREA
6X .050
[1.27]
8
1
.189-.197 2X
[4.81-5.00] .150
NOTE 3 [3.81]
4X (0 -15 )
4
5
8X .012-.020
B .150-.157 [0.31-0.51]
.069 MAX
[3.81-3.98] .010 [0.25] C A B [1.75]
NOTE 4
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
0 -8 [0.11-0.25]
.016-.050
[0.41-1.27] DETAIL A
(.041) TYPICAL
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A SOIC - 1.75 mm max height
8X (.061 )
[1.55]
SYMM SEE
DETAILS
1
8
8X (.024)
[0.6] SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK SOLDER MASK

METAL METAL UNDER
OPENING OPENING SOLDER MASK
EXPOSED
METAL EXPOSED
METAL
.0028 MAX .0028 MIN
[0.07] [0.07]
ALL AROUND ALL AROUND
NON SOLDER MASK SOLDER MASK

DEFINED DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A SOIC - 1.75 mm max height
8X (.061 )
[1.55] SYMM
1
8
8X (.024)
[0.6] SYMM
(R.002 ) TYP
5 [0.05]
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE

BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

TLV2186 Precision, Rail-to-Rail Input and Output, 24-V, Zero-Drift Operational Amplifier

Uploaded by

Copyright:

Available Formats

TLV2186 Precision, Rail-to-Rail Input and Output, 24-V, Zero-Drift Operational Amplifier

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TLV2186 Precision, Rail-to-Rail Input and Output, 24-V, Zero-Drift Operational Amplifier

Uploaded by

Copyright:

Available Formats

Product Order Technical Tools & Support &

Folder Now Documents Software Community

2 Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated

Product Folder Links: TLV2186

5 Pin Configuration and Functions

Copyright © 2019, Texas Instruments Incorporated Submit Documentation Feedback 3

Input Common-mode (V–) –0.5 (V+) + 0.5

6.2 ESD Ratings

6.3 Recommended Operating Conditions

Supply Single supply 4.5 24

6.4 Thermal Information

4 Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated

Product Folder Links: TLV2186

6.5 Electrical Characteristics

Voltage output swing from RL = 10 kΩ 60 100

Quiescent current per 90 130

Copyright © 2019, Texas Instruments Incorporated Submit Documentation Feedback 5

6.6 Typical Characteristics

6 Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated

Product Folder Links: TLV2186

at TA = 25°C, VS = ±12 V, VCM = VS / 2, RL = 10 kΩ (unless otherwise noted)

-1200 -900 -600 -300 0 300 600 900 1200

Figure 3. Input Bias Current Distribution

Copyright © 2019, Texas Instruments Incorporated Submit Documentation Feedback 7

at TA = 25°C, VS = ±12 V, VCM = VS / 2, RL = 10 kΩ (unless otherwise noted)

-30 -30 -20

8 Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated

Product Folder Links: TLV2186

at TA = 25°C, VS = ±12 V, VCM = VS / 2, RL = 10 kΩ (unless otherwise noted)

Power Supply Rejection Ratio (dB)

Figure 13. CMRR vs Temperature Figure 14. PSRR vs Temperature

Voltage Noise Density (nV/—Hz)

Total Harmonic Distortion + Noise (dB)

0.0001 -120 0.001 -100

Figure 17. THD+N vs Frequency Figure 18. THD+N vs Output Amplitude

Copyright © 2019, Texas Instruments Incorporated Submit Documentation Feedback 9

at TA = 25°C, VS = ±12 V, VCM = VS / 2, RL = 10 kΩ (unless otherwise noted)

Quiescent Current (µA)

Open-loop Gain (dB)

Gain = –1, 10-mV step

10 Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated

Product Folder Links: TLV2186

at TA = 25°C, VS = ±12 V, VCM = VS / 2, RL = 10 kΩ (unless otherwise noted)

Gain = 1, 10-mV step

Time (10 Ps/div) Time (10 Ps/div)

Time (10 Ps/div) Time (10 Ps/div)

Gain = 1, 10-mV step Gain = –1, 10-mV step

Copyright © 2019, Texas Instruments Incorporated Submit Documentation Feedback 11

at TA = 25°C, VS = ±12 V, VCM = VS / 2, RL = 10 kΩ (unless otherwise noted)

Gain = 1, 10-V step Gain = –1, 10-V step

12 Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated

Product Folder Links: TLV2186

at TA = 25°C, VS = ±12 V, VCM = VS / 2, RL = 10 kΩ (unless otherwise noted)

Channel Seperation (dB)

Figure 37. EMIRR vs Frequency Figure 38. Channel Separation

Copyright © 2019, Texas Instruments Incorporated Submit Documentation Feedback 13

7.2 Functional Block Diagram

+IN 24-V OUT

14 Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated