CCT-3300 series

Conductivity (TDS) Controller

Operation Manual
 Notes before Operation

1. Notice before operation:

（1） Carefully read the relevant parts of this manual before installation
and operation to prevent wrong operation, measurement error and damage
of instrument.
（2） Improper installation and unsuitable flow speed will cause big
measurement error, so please read the installation passage in detail.
（3） This instrument is precise electrochemical measurement, and its
installation and operation should be performed by technicians with relevant
professional knowledge.
2. Maintenance items:
（1） The meter’s quality guarantee is one year from the date of
purchasing. During this period, if the meter has quality problems,
manufacturer is responsible for maintenance work for free or changes it.
（2） Manufacturer offers the maintenance service for whole life of the
sold meters.
（3） If the damage of the meter is caused by the following reasons, it is
out of the maintenance service:
A、 The meter is burned or foundered caused by improper usage and
maintenance.
B、 The meter is refitted or misused without permit.
C、The meter is destroyed under the condition out of company’s regulation.
D、 The relevant damage caused by choosing the wrong type.
E、 The cable damage and rupture caused by improper installation and
usage.
F、 The incorrect measurement of the sensor caused by disconnecting or
connecting wires personally.
G、 The inner broken wire caused by indiscreetly disassembling.
 Catalogue

I. Product General Introduction...........................................................................1

1．1 Main technical index............................................................................1
1．2 Applications ..........................................................................................2
1．3 Products classification ........................................................................2
1．4 Notices of product installation............................................................2
1．5 Main technical index............................................................................3
II. Outline Dimension and Rear Terminals ..........................................................4
2．1 Outline dimension ................................................................................4
2．2 Rear terminals ......................................................................................4
2．3 Wire connection ...................................................................................5
III. Electrical Connection ...................................................................................6
3．1 mA wire connection diagram..............................................................6
3．2 Electrical connection ...........................................................................7
3．3 High limit and window control. ...........................................................7
IV. Introduction of Front Panel and Key Functions ...........................................8
4．1 Front panel and main menu display..................................................8
4．2 Key board functions Introduction.......................................................9
V. Introduction of Operation Menu ......................................................................9
VI. Introduction for Electrode Installation .......................................................10
6．1Selection for electrode constant .......................................................10
6．2 Outline dimension of the electrode .................................................10
6．3 Installation method ............................................................................ 11
6．4 Installation and maintenance ...........................................................12
VII. Failure Judgment for Meter and Electrode.................................................13
VIII. Complete Set of Products ...........................................................................14
IX. Ordering Directory .....................................................................................14
I. Product General Introduction

CCT-3300 series conductivity (TDS) measurement controller is a high-technology

innovative product. Product performance and function updated to a new level. It is
a product with high performance and price ratio for inline water quality conductivity
analysis.

．1 Main Technical Index

1．

No adjustable component inside the instrument, totally programmed

automatic calibration, higher reliability;

Automatic measurement range shift, digital temperature compensation.

Support conductivity cell constant (0.1 cm-1, 1.0 cm-1, 5.0 cm-1, 10.0 cm-1),
measurement range compatible with liquid from pure water to concentrated
solution, named online conductivity superman.

Conductivity (uS/cm) or TDS (ppm) engineering unit display can be chosen
in operation.

present water temperature (℃) / transmitting current (4~20mA) can be
check onsite.

Measurement and calibration program for calculation and measurement
inspection organization.

Isolated, transferable 4~20mA current output, two points transmitting range
random setting within full scope. Support all the two wire PLC system
under transmitter model.

Conductivity high limit alarm, high limit value and backlash value random
setting within full measurement scope.

Patent short housing and fast installation method to save more space for the
project,

High illumination, pure white backlight LCD display in accordance with
international trend.

Industrial standard wire contact, EMC electromagnetic compatible design,
platform design development, serial product classification.

Meeting international electronic power supply regulation, AC ,DC current
input which with non polarity wire connection,

Our products with strict quality management , SMT (Surface Mounted
Technology), AOI (automatic optical inspection (system), ICT …

Complete manufacturing technique management, and quality management.

Electrode will be calibrated, tested, packed one by one.

1
 ．2 Applications
1．

This series is widely used for the water treatment control and monitoring of water
treatment (high salt content), concentrated solution, recirculating cooling water and
etc.

．3 Products classification
1．

Power Constant
Model Frequency(Hz) Current loop modes Display
supply selection
Three digits and a
CCT-3300E DC 24V --------------- Instrument/Transmitter 0.1-1.0
half
Three digits and a
CCT-3310E AC 110V 50/60 Instrument/Transmitter 0.1-1.0
half
Three digits and a
CCT-3320 AC 220V 50/60 Instrument/Transmitter 0.1-1.0
half
Three digits and a
CCT-3320E AC 220V 50/60 Instrument/Transmitter 0.1-1.0
half
Three digits and a
CCT-3320T AC 220V 50/60 Instrument/Transmitter 0.1-1.0
half
Note: The model with E is the EMC enhancement type.
CCT-3320T(Conductivity Monitor) without any control outputs.

．4 Notices of product installation

1．

i. Please choose CCT-3300E (power supply 24V DC) if the onsite with damp
environment or systems with 24V power supply.
ii. If the onsite voltage is unstable or the site is far away from the power
station, please use wide range AC/DC voltage-stabilizing type DC 24V
power supply, please choose CCT-3300E.
iii. If the measurement value unstable caused by using converter system,
electronic device for water treatment, UV light electronic ballast device,
power supply pollution, please choose CCT-3320E
iv. Under the small power generation device which the power unstable, or far
away from the power supply, please use wide range AC/DC
voltage-stabilizing type DC 24V power supply, please choose CCT-3300E
v. UV does harm to the LCD display screen, so please do not place the meter
under sunshine.

2
 ．5 Main technical feature
1．

Name of product CCT-3300 series of conductivity/TDS Controller

Display LCD display
-1 -1
Auxiliary electrode Constant 0.10 cm 1.000 cm 5.000 cm-1 10.0 cm-1
0.070- 0.130
Electrode coefficient range -1 0.70 -1.30 cm-1 3.50 -6.50 cm-1 7.00 -13.0 cm-1
cm
Auxiliary electrode accuracy
0.5~199.9µS/cm 1.0~1999µS/cm 0.05~9.99mS/cm 0.5~19.99mS/cm
measurement range
conductivity 0.5µS/cm ~ 19.99mS/cm
Measurement
range TDS 0.25ppm~ 9.99 ppt
temperature
0.0~50.0℃
Resolution conductivity 0.01µS/cm
TDS 0.01ppm
temperature 0.1℃
conductivity 1.5level
Accuracy TDS 1.5level
temperature ±0.8℃

Temperature compensation
NTC10K temperature component
Working Environment Temp.0~50℃ Relative Humidity: ≤80%RH

Transmitting output（4~20mA） isolated/transferable/reversible /transmitter mode/meter mode

Loop resistance 0--400Ω accuracy: ±0.1mA
Control Output port double contact relay output (ON/OFF)
output load capacity AC 220V/AC110V/DC24V 3A Max
Power consumption <2.5W
Power supply CCT-3300E CCT-3310E CCT-3320/CCT-3320E CCT-3320T
DC 24V AC 110V AC 220V ±10% AC 220V ±10%
±4V ±10%
Frequency（Hz） ------ ------ 50/60 50/60
Installation
Panel mounted ,fast installation clamp
Dimension 48mm×96mm×80mm(H×W×D)
Slot dimension 44mm×92mm(H×W)
Weight 0.27kg

3
II. Outline Dimension and Rear Terminals

．1 Outline dimension
2．

．2 Rear terminals
2．

CCT-3300E

CCT-3310E

4
 CCT-3320/CCT-3320E/CCT-3320T
Note:CCT-
Note:CCT-3320T RELAY terminal is blank, without any connection.

．3 Wire connection
2．

W Connect white wire of electrode(WHITE)

G/B Connect green wire of electrode(GREEN)

Y Connect yellow wire of electrode (YELLOW)

R Connect red wire of electrode(RED)

I+\I- Under instrument mode, power supplied by meter

Under transmitter mode , power supplied by conditioning
T+\T-
module
RELAY relay contact (ON/OFF contact)

24V(A)/24V (B) DC power supply

0V/ 110V Power supply AC 110V

0V/ 220V Power supply AC 220V

Protective terminal of EMC ground connection（Earth）

NC Empty terminal（no wire connection in-side）

5
III. Electrical Connection

．1 mA wire connection diagram

3．

Connection diagram of 4~20mA signal under different modes

6
 ．2 Electrical connection
3．

Connection diagram of ON/OFF relay

．3 High limit and window control.

3．

7
 The water quality is limited within HIGH limit
If the meter is used for pharmaceutical industry, food, drink, water purification and etc,
when the water quality is limited at HIGH limit, the solenoid valve will switch the water

flow direction to make sure the water purity. When the water quality at LOW limit, the

meter will back to normal operation. The space between HIGH and LOW is backlash.

Backlash will avoid the solenoid valve shock.

Controlled section between HIGH and LOW

When the mete is used for circulating cooling water, cooling liquid, cleaning solution,
when the water quality is so bad that at HIGH, the meter will discharge the water.
When the water quality is better at LOW, discharge stopped.

IV. Introduction of front panel and key functions

．1 Front panel and main menu display

4．

8
 ．2 Key board functions Introduction
4．

Key sign Name Function

1.parameter setting to select thousand,hundred,ten and unit in circulate
select
2.radix point position setting
key
3.Measurement switch to display conductivity/TDS
1. Adjust the value under setting status.
Add key 2. Check the temperature/mA/ conductivity (TDS) reading under measurement
status.
Enter 1.Enter parameter setting under main menu
key 2.Save the parameters and enter next menu

V. Introduction of Operation Menu

Under main measuring menu, pressing “ ” for three seconds and enter setting menu
automatically

order Setting Menu name Introduction for function

Electrode The sign “C=”blink on display screen, operating selectkey and add
1 constant key to input the needed electrodeconstant value, pressing enter
setting key to save andenter next parameter setting.
radix point The radix point sign on display screen blink, press select key to set
2 radix point position; press enter key to save and enter next
setting parameter setting.
Measurement The sign “Unit” blink on display screen, press add key to select
3 measurement unit （ppm ，ppt, µS/cm or mS/cm），press enter key
unit setting to save and enter next parameter setting.
The sign “ 4mA”blink on display screen, press select key and add
4mA transfer key to input the 4mA transferable value and press enter key to save
4 and set the radix point ( the same procedures as electrode constant
v setting
setting ),press enter key to save and enter next parameter setting.
20mA The sign “ 20mA”blink，setting the data according to 20mA and
5 transfer press enter key to set the radix transferable value，press enter key
setting enter the next parameter setting
Alarm the sign “Hi” and blink, press select key and add key to
input the needed hi-limit value; press enter key to save, and then set
6 hi-limit the radix point bits, press enter key to save and enter the next
setting parameter setting.
9
 Alarm The sign and “Lo” blink, other setting is the same as the
7 release above, pressing enter key to save and enter the next parameter
setting.
setting
8 Alarm switch Obligate function ,No at present

Note:CCT3320T Setting Menu don’t contain 6、7、8、item.

VI. Introduction for Electrode Installation

．1Selection for electrode constant

6．

The measurement range depends on the electrode constant, so please choose the suitable
electrode constant for your applications.

．2 Outline dimension of the electrode

6．

Outline dimension of the electrode

10
 ．3 Installation method
6．

Please follow the correct installation method to install the electrode strictly. The
incorrect installation will cause the reading error.

）Picture 1a the fitting is too long and the stretched parts is too short, which will
1）
lead to the dead space in electrode and incorrect measurement. please follow the
picture 1b (FLOW=stretch into flow direction deeply)。 。

Installation 1a installation 1b

2 ） Picture 2a, the installation mode will lead to air space and incorrect
measurement and instability. Please follow the picture 2b

Installation 2a installation 2b

11
 ）Picture 3 , there will be air space inside the pipeline, the air will cause
3）
incorrect reading.

4）Picture 4a, the below installation will cause incorrect reading ,because
the water can not through the measuring hole of the electrode.

．4 Installation and maintenance

6．

Notes:
（1） The electrode should be installed in a place in the pipeline where the stream is steady
and air bubbles are hard to generate.
（2） No matter the conductance cell is horizontally or vertically installed, it should be
deeply inserted into the moving water.
（3） The conductivity signal is weak electronic signal and its collecting cable should be
separately installed. When threading cable joint or connecting terminal board is used,
to avoid wetting interference or breakdown of measurement unit circuit, they should
not be connected to the same group of cable joint or terminal board with the power
line or control line.
（4） When the measurement cable needs to be lengthened, it’s recommended to make an

12
 agreement with the factory before placing an order.
（5） Please keep the measuring part of electrode clean, and do not directly contact the
surface by hands or contact with the oil stain objects
（6） Electrode is a kind of precision components, so please do not change any part of the
electrode. The accuracy will be incorrect if the electrode was destroyed by the
strong acid, strong alkali, scrape from machine and etc.
（7） The meter is made by precision integrated circuit and electronic components, so it
needs to place in case or dry environment.
（8） In order to guarantee the safety operation, pls checking after installation then switch
on.

VII. Failure Judgment for Meter and Electrode

When the reading is incorrect or unstable, please check the meter and electrode.
a．Distinguish the failure source which comes from meter or electrode
Firstly, remove the white wire from the wire terminal and check the conductivity
reading, if the reading is 0 and stable, the meter is good. The problem can be
initially identified from the electrode installation.
b. Sensor installation question failure judgment.
Remove the electrode from the fittings, and then use the electrode to test the
water quality (user already know the conductivity reading of the water before
test) . If the reading is correct, so the installation is correct. If the reading with
error, so the electrode failure.
C. Meter mode or transmitter mode of 4~20mA judgment.
Before the judgment please makes sure there is no wire connection on the terminal.
mA mode Output terminal Voltage of terminal Voltage of cable
Meter mode I+/I- >12V DC no
Transmitter mode T+/T- no DC24V

General fault inspection and trouble shooting:

Symptom Possible factor Trouble shooting methods

A. No power supply connection A. Check to the wire connection of power supply

1. No reading
B. Instrument fault B. Maintained by professional.
A. Wire connection of CELL
incorrect A. Check the wire connection of manual.
2.Unstable B. Adjust the pipe or select another measurement point
Incorrect electrode installation
reading C. Use the steady water supply to eliminate the meter
B. Unstable flow speed
factor.
D. So fast flow speed in some part

13
 A. Reset the electrode constant
A. Incorrect constant Setting
3.Serious B. Change the electrode by new one.
B. The electrode constant is changed
error of C. Install the electrode at where the flow’s speed is
reading Incorrect electrode installation suitable.
D. Put the electrode deeply into the flowing water.
A. Set the transfer setting again
4.different mA
A. Reviver transfer error B. Loop resistance is too large, enlarge the
reading
B. Not up to 20mA cable.
between
C. Incorrect setting on sending C. Set the corresponding of mA and reading
sender and
D. mA transfer error again.
receiver
D. Use the ammeter to check the current.

VIII. Complete Set of Products

Conductivity /TDS transmitting controller one piece（with a pair of fast

installation clamp）
Electrode one piece (5m cable length)
Operation menu one piece

IX. Ordering Directory

CCT-3300 series including 4 models, please check the below items to choose the suitable power
supply, material, fixed method for your applications

Model No. Power supply Electrode Connection Electrode material

constant
CCT-3300E DC 24V 0.10 cm-1 316L
CCT-3310E AC 110V 1.00 cm-1 316L plastic
CCT-3320 AC 220V 5.00 cm-1 □ Thread Graphite
CCT-3320E AC 220V 10.00 cm-1 □ ferrule Graphite
CCT-3320T AC 220V 10.00 cm-1 Graphite

：
NOTE：

： 1m, 5m, 10m, 20m (please indicate another especial length before placing an
Cable length：

order).

The model with E is EMC enhancement type

CCT-3320T(Conductivity Monitor) without any control outputs.

*Without the influence on the operation, any small change or improvement on the products by

the manufacturer will not be notified separately. Please make the object as the standard.

14