Controlado Quemador
Controlado Quemador
Controlado Quemador
RMO... / RMG... and this Data Sheet are intended for use by OEMs which integrate
the burner controls in their products.
Use, features
Use The burner controls are designed for the startup and supervision of single- or multi-
stage forced draft burners in intermittent operation. The RMO... is for use with forced
draft oil burners, the RMG... for forced draft gas burners. When firing on oil, yellow-
burning flames are supervised with photoresistive detectors QRB1B..., and blue-
burning flames with blue-flame detectors QRC... When firing on gas, the flame is su-
pervised with an ionization probe or flame detector QRA... (with ancillary unit
AGQ2...A27).
CC1N7142en
Riello Siemens Building Technologies
28.10.2003 HVAC Products
Application-specific When firing on oil
features - Contact for preheating the oil
- Monitoring of time for preheating the oil
- Limitation of the number of repetitions
General
- Undervoltage detection
- Accurate and reproducible program sequence owing to digital signal handling
- Controlled intermittent operation after 24 hours of continuous operation
- Multicolor display of fault and status messages
Warning notes
• All activities (mounting, installation and service work, etc.) must be carried out by
qualified staff
• Before performing any wiring changes in the connection area, completely isolate
the burner control from the mains supply (all-polar disconnection)
• Ensure protection against electric shock hazard by providing adequate protection
for the burner control’s terminals
• Check to ensure that wiring is in an orderly state
• Press the lockout reset button of the burner control or the reset button extension
AGK20.43 only manually (applying a force of no more than 10 N), without using
any tools or pointed objects
• Fall or shock can adversely affect the safety functions. Such units may not be put
into operation, even if they do not exhibit any damage
Mounting notes
• Ensure that the relevant national safety regulation are complied with
Installation notes
• Observe the permissible lengths of the detector cables (refer to «Technical data»)
• Always run the high-voltage ignition cables separately while observing the greatest
possible distances to the unit and to other cables
• Install switches, fuses, earthing, etc., in compliance with local regulations
• Ensure that the maximum permissible current ratings will not be exceeded (refer to
«Technical data»)
• Do not feed external mains voltage to the control outputs of the unit. When testing
the devices controlled by the burner control (fuel valves, etc.), the burner control
may never be connected
• Live and neutral conductors may not be interchanged
2/19
Commissioning notes
• When commissioning the plant or when doing maintenance work, make the follow-
ing safety checks:
3/19
Type reference
RMO503SE --- ---
RMO503SE/K2 --- ---
RMG508SE x x
RMG508SE/GB --- ---
RMG509SE x x
RMG509SE/K --- ---
Service notes
• Each time a unit has been replaced, check to ensure that wiring is in an orderly
state. Make the safety checks as listed in «Commissioning notes»
Disposal notes
The unit contains electrical and electronic components and may not be disposed of
together with household garbage.
Local and currently valid legislation must be observed.
Mechanical design
The housing of the burner controls is made of impact-proof, heat-resistant and flame-
retarding plastic.
4/19
Firing on oil
Type reference Mains voltage tw TSA t1 t3 t3n t4 t42 Response in the event of loss of
max. max. min. min. min. min. min. flame during operation
RMO503SE AC 220...240 V ¹) 2s 5s 37 s 20 s 7s 7s 6s Max. 3 repetitions, then lockout
RMO503SE/K2 AC 220...240 V ¹) 2s 5s 37 s 20 s 7s 7s --- Max. 3 x repetitions, then lockout
Firing on gas
Type reference Mains voltage tw ²) TSA t1 t3n t4 t10 Response in the event of loss of flame during
max. max. min. min. min. max. operation
RMG508SE AC 220...240 V ¹) 2s 3s 38 s 2s 10 s 10 s Lockout
RMG508SE/GB AC 220...240 V ¹) 2s 3s 38 s 2s 10 s 10 s Lockout
RMG509SE AC 220...240 V ¹) 2s 2s 64 s 1,3 s 10 s 15 s Lockout
RMG509SE/K AC 220...240 V ¹) 2s 3s 53 s 2,2 s 8s 12 s Lockout
¹) For applications outside the European Community, operation at mains voltage AC 200...240 V ±10 % is ensured
²) Max. 20 s, when «CPI» or «LP» are not in the idle position
Ordering
Diagnostic tool
(refer to Data Sheet 7614)
- Hardware OCI400
- Software ACS400
5/19
6/19
The flame signal amplifier responds only to the DC component of the flame signal.
→ A short-circuit between ionization probe and ground causes the burner control to ini-
tiate lockout!
RMG...
M
- + Legend
+
C Electrolytic capacitor 100...470 µF; DC 10...25 V
ION C
ION Ionization probe
M Microammeter, Ri max. 5000 Ω
At mains voltage UN
AC 220 V AC 240 V
Detector voltage at QRA... (with no load)
Until the end of «tw» and after controlled shutdown DC 400 V DC 400 V
After the end of «tw» DC 300 V DC 300 V
Detector voltage
Load by DC measuring instrument Ri > 10 MΩ
Until the end of «tw» and after controlled shutdown DC 380 V DC 380 V
After the end of «tw» DC 280 V DC 280 V
DC current detector signals with flame detector Min. required Max. possible
QRA...
Measurement at the flame detector DC 200 µA DC 500 µA
7/19
7142a09/1003
7142a10/1003
RMG... RMG...
1 15 7 10 1 15 7 10
br bl rt sw br bl rt sw
sw bl AGQ2...A27 sw bl AGQ2...A27
QRA
+
QRA
-
Measuring circuit for RMO... For detector currents, refer to «Technical data»
detector resistance M- +
measurement Legend
QRB1B... Photoresistive detector
QRB...
M Microammeter, Ri max. 5,000 Ω
8/19
kOhm
Lux
7142d03/1102
9/19
Undervoltage Safety shutdown from operating position in the event mains voltage drops below ap-
prox. AC 165 V.
Repetition in the event mains voltage exceeds approx. AC 175 V.
Controlled intermittent After no more than 24 hours of continuous operation, the burner control will automati-
operation cally initiate a safety shutdown followed by an unshortened repetition of startup.
Monitoring of time of oil If the oil preheater’s release contact does not close after 600 seconds, lockout will be
preheater initiated.
Flame supervision When changing from the operating state to standby or repetition (only when firing on
oil), a flame signal is permitted for a period of 10 seconds after the heat demand con-
tact has opened. Otherwise, lockout will occur.
Fuse If fuse is blown due to overload, the unit’s life expectancy will be shortened.
10/19
Cause Response
General
Mains failure Repetition with unshortened program
sequence
Voltage has dropped below the undervoltage Repetition with unshortened program
threshold sequence
Burner does not ignite after «TSA» Lockout
Afterburn time > 10 seconds Lockout
Lockout In the event of lockout, the burner control remains locked (lockout cannot be changed)
and the red signal lamp will light up.
This status is also maintained in the event of a mains failure.
Resetting the burner If lockout occurs, the burner control can immediately be reset. To do this, keep the
control lockout reset button depressed for about 1 second.
11/19
Operation Lockout reset button EK... is the key operating element for resetting the
7142z01/1002
EK burner control and for activating / deactivating the diagnostic functions.
Red The multicolor LED is the key indicating element for both the visual
7142z02e/1102
Yellow diagnosis and the interface diagnosis.
Green
LED
Both EK... and LED are located under the transparent cover of the lockout reset button.
Visual diagnosis:
In normal operation, the different operating states are displayed in the form of color
codes according to the color code table below. The interface diagnosis is activated by
pressing the lockout reset button for at least 3 seconds (refer to Data Sheet 7614). If,
by accident, the interface diagnosis has been activated, in which case the slightly red
light of the signal lamp flickers, it can be deactivated by again pressing the lockout
reset button for at least 3 seconds. The moment of switching over is indicated by a
yellow light pulse.
xxxxxxxx
EK
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
12/19
OCI400
Lockout position Lockout position Lockout position
Visual diagnosis Interface diagnosis
On Flashing PC / analyzer
Reset
EK EK EK
7142z04e/1102
Error code table
>3s xxxx xxxx
xxxx xxxx
>3s <3s
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
During the time the cause of the fault is diagnosed, the control outputs are deactivated.
- Burner remains shut down
- External fault indication remains deactivated
- Fault signal «AL» is activated
The fault diagnosis is quit and the burner switched on again by resetting the burner
control. To do this, press lockout reset button for about 1 second.
13/19
7142a06e/1203
AL EK
RMO503SE
RMO503SE/K2
Power
supply µC-control
FSV
K1 K4-2
K2-2
F
K2-1 K3 K4-1
1 15 9 5 10 4 8 3 11 14 12 13
1 15 6 9 7 5 10 4 8 3 11 14 12 13
AL OW
R
STB Z
1 W
1) M
br sw M
HS
QRC
Si BV1 BV0 BV3 BV2
L bl QRB
7142a12e/1003
RMG508SE/GB AL EK
Power
µC-control
supply
FSV
K1
K3 K4-2
K2-2
F K4-1
K2-1
1 15 10 6 5 3 4 7 9 8 14 12 13 11 2
1 15 10 6 5 3 4 7 9 8 14 12 13 11 2
ION (Option)
CPI
STB AL LP
R BV1
HS W BV2
Si
L M Z
N
Without CPI wiring between terminal 2 and terminal 8
14/19
7142a07e/1003
RMG508SE AL EK
RMG509SE
RMG509SE/K Power
µC-control
supply
FSV
K1
K3 K4-2
K2-2
F K4-1
K2-1
1 15 10 6 5 3 4 7 9 8 14 12 13 11 2
1 15 10 6 5 3 4 7 9 8 14 12 13 11 2
ION (Option)
CPI
STB AL LP R
BV1 BV3
W
HS BV2
Si
L M Z
N
Without CPI wiring between terminal 2 and terminal 8
15/19
7142d01e/1003
R
W 8
t0 tw
OW 4
max. 600 s
M 7
t1 t3n
Z 12
t3 TSA
BV0 3
BV1 10
BV2 13
t4 t42
BV3 14
FS 9
Yellow Flashing yellow Green
LED
Response in the event of loss of flame during operation (max. 3 failures permitted)
FS 9
RMO503SE/K2 A A´ B B´ C D
STB 1
7142d04e/1003
R
W 8
t0 tw
OW 4
max. 600 s
M 11
t1 t3n
Z 12
t3 TSA
BV0 3
BV1 10
BV2 13
FS 9
Yellow Flashing yellow Green
LED
Response in the event of loss of flame during operation (max. 3 failures permitted)
FS 9
16/19
RMG508SE A B B´ C D
RMG509SE STB 1
RMG509SE/K t0
7142d02e/1102
R 8
W
tw TSA
CPI 2
t1
LP 4
t10
M 7
t3n
Z 13
BV1 12
t4
BV2/LR 14
BV3 11
FS 10
Flashing
Yellow yellow Green
LED
Yellow
Response in the event of loss of air pressure
LP 4
1) 1) 1) 1)
AL 5
RMG508SE/GB A B B´ C D
STB 1
t0
7142d05e/1003
R 8
W
tw TSA
CPI 2
t1
LP 4
t10
M 7
t3n
Z 13
BV1 12
t4
BV2/LR 14
FS 10
Flashing
Yellow Yellow Green
LED
Yellow
Response in the event of loss of air pressure
LP 4
1) 1) 1) 1)
AL 5
17/19
18/19
Dimensions in mm
64,5
110,7 7142m01/1002
RMO503SE
LMO88.580A2RL
220-240 V
TSA 5 s
85,35
103,7
base
7142m02/1002
RMO503SE
LMO88.580A2RL
220-240V
TSA 5 s