certified Qualitysystem

535e/08/96

ISO 9001 / EN 29001

Reg. Nr. 10529 A Honeywell Company TMG 740-3
Burner Control Box

For high performance forced draught

and dual fuel burners in intermittent operation
(single or two stage versions).
Suitable flame detectors:
- Ionisation probe
- UV sensor
- Infra-red flicker detector

INTRODUCTION

The TMG 740-3 burner control box is capable of controlling

and monitoring medium to high performance forced draught TECHNICAL DATA
and dual fuel oil/gas burners in single or two stage versions.
It can be used, as prefered, for multi-stage or modulating Supply voltage 220 / 240 V (-15... +10%)
operation with burners of any nominal rating as well as in 50 HZ (40 - 60 Hz)
direct air heaters (as per DIN 4794). AC frequency variations result in proportional timing
Different model designations identify the control boxes deviations
according to programme times for varying national standards, Fuse rating 10 A rapid, 6 A slow
or for special applications e.g. high-speed steam generators. Power consumption approx. 15 VA
A special version is available for operation with ignition Max. current per
spark monitoring in conformance with French national output terminal 4A
regulations. Total 6A
The TMG 740-3 is fully interchangeable with the earlier Sensitivity
versions -1 and -2. Ionisation input 1.6 µA
UV input 70 µA
Min. sensor current
CONSTRUCTIONAL FEATURES Ionisation/IR probe 5 µA = 2 LED
UV tube 250 µA = 2 LED
The control box is enclosed in a protective, flame resistant, Air proving switch 6 A, 220 V
transparent, plug-in type plastic housing, and includes: Reset delay none
- Synchronous motor with gearbox driving cam switch Flame detector cable
- Cam switch with informative, coloured programme Ionisation 50 m normal cable
indicator 100 m screened cable
- 16-way cam switch assembly controlling the programme UV tube 100 m normal cable
sequence 200 m screened cable
- 2 DC relays and 1 remanence relay on common yoke UV tube UVZ 780 blue low sensitivity
- Plug-in printed circuit board with mains transformer, LED UVZ 780 white medium sensitivity
display and electronic components UVZ 780 red high sensitivity
On the underside of the unit are robust plug terminals where Weight incl. base 1100 g
the air proving switch and monitoring of the ignition spark Mounting attitude any
can be programmed via two wire links which can be cut as Insulation standard IP 44
required. The flame detector selection switch is also situated Permissable ambient temp. -20° C to +60° C incl.
on the the underside of the unit. Classified acc. to EN 298 BTLLXN

Model No. 32-32 63-55 43-35 13-53*

The following important indicators and operating controls sec. sec. sec. sec.
can be found on the front of the control box:
- Reset button incorporating signal lamp for malfunction Pre-purge time supervised 24 60 32 4
(lockout) Pre-purge time with air
- Coloured programme indicator damper open 30 60 40 6
- Flame signal indicator with 5 LED’s Pre-ignition time fixed 3 4 4 1
- Central screw fastening Start valve safety interval 2 3 3 3
Pilot valve safety interval 3 5 3 5
Pilot valve switch on time 11 13.5 14 8
Main valve 1 safety interval 2 5 5 3
Valve 1 delay 9 10 10 6
Valve 2 delay 6 20 10 4
Post-purge 7 16 10 -
* For high-speed steam generators. Prescribed ventilation
must be verified.
1
TECHNICAL FEATURES - A separate connection for a pilot valve PV is provided,
which is again closed at the end of the second safety
1. Flame detection interval. The heat output of the gas flow which is controlled
by this valve must not exceed 120kW.
The following types of flame detector can be used: - The terminal for the start valve SV must not be used when
- Ionisation electrode, where the mains supply provides a connecting the pilot valve PV.
neutral earth connection. Suitable for gas burners (signal - Together with the start valve SV, a total of 3 power levels
current from flame cannot be influenced by interference are available for use. The gas flow controlled by valves
from ignition spark). SV, V1 and V2 must lead to a common nozzle unit.
- UV sensor type UVZ 780 red, suitable for gas, oil and dual - To determin the heating power of the gas flow controlled
fuel burners. by the pilot- and start valve, EN 676 has to be consulted.
- Infra-red flicker detector type IRD 820 and 1020 for all - In addition to the built-in button with signal lamp, it is also
types of burner. possible to connect a remote lockout indicator and reset
The flame signal amplifier is adjusted to the the type of switch.
detector probe fitted by using the flame detector selection - For monitoring of the ignition spark, link 1 on the base of
switch on the underside of the unit. If the IRD flicker detector the control box must be cut. In this case, flame detection
is used, the selection switch must be adjusted to the "ION" is carried out by a UVZ 780 ultra-violet sensor.
position.
Flame detection is only operational when the switch position 3. Safety
selected corresponds to the type of detector probe
connected. The design and programme sequence employed in the
By optimally matching the amplifier to the detector probe, control boxes in the TMG 740-3 series conform to the
considerably longer signal transmission distances with less presently applicable European standards and regulations.
sensitivity to interference can be achieved. The following features exceed the requirements of most
standards, and therefore ensure additional safety:
- After a normal shutdown, the stray light test is started
immediatly by the control box which directs an increased
voltage to the UV sensor. The very important extinguishing
function of the sensor can therefore be checked. If the fuel
valve does not close correctly, or a sensor or amplifier
malfunction occurs, shutdown and lockout take place
after approx. 20 sec., even if the controlling thermostat
is open.
- The contacts responsible for the release of fuel are checked
when the programme starts, to ensure that they have not
become welded together.

The flame signal current indicator consists of a five stage 4. Mounting and Electrical Installation
LED display which shows the signal current continuously.
An indication of the strength of the flame signal current is At the base:
therefore always given. Fluctuations in the monitoring - 3 earth terminals, with an additional tag for the burner
sensitivity can be noticed at an early stage, earth.
and appropriate corrective action can be - 3 neutral terminals, with a fixed internal through connection
taken. to the neutral input, terminal 8.
If the infra-red flicker detector IRD 820 or - 2 separate slide-in plates and 4 fixed, threaded knockouts
920 is employed, the flame signal current (PG 11 thread) as well as a wiring opening from below, to
indicator on the control box is not facilitate wiring of the base.
relevant. In this case, the IRD - A keyed fit ensures that the wrong control box type cannot
indicator is the decisive indication be fitted to the base. The corresponding control box
of flame signal strength. designation is shown in lettering on the base.
Flame signal current indicator
General:
- Can be mounted in any position, insulated as per IP 44
2. Burner Control standard (unaffected by water spray). The control box and
detector probes should not however be subjected to
- Burners can be operated with or without post-purge. excessive vibration. With the UVZ 780 ultra-violet sensor,
This varies according to model (see technical data) care should be taken to ensure that a good electrical
and is activated when the burner motor is connected to contact to the burner exists via the metal flange.
terminal 19. - If an ionisation electrode is used, appropriate protective
- Air damper operation is monitored to ensure the nominal measures are required in order to avoid contact with the
air volume during pre-purge and in the starting position electrode while installation work is being carried out.
before fuel is released. If confirmation of the damper Trouble-free operation with this type of flame detection is
positions "MIN" and "MAX" is not received, the control not possible if a voltage of over 25 volts is measured
box start sequence is interrupted. between neutral and earth. In this case, provision must be
- The air proving switch is checked for corrrect operation made for a separate isolating transformer.
before the start, and air pressure is monitored during pre- - The maximum lengths for the detector probe cables,
purge as well as during normal operation. In normal use, depending on the type of cable installed, are listed in the
switch contacts with a rating of 6A/220V are sufficient. technical data and must be adhered to without fail. Laying
Additional switch contacts which are to be monitored can the cables parallel to mains cabling over long distances
be connected between terminal 18 and the air proving should be avoided, and the use of multiple core cable is
TMG 740-3

switch working contact. In this case, jumper II on the also not permitted.
underside of the control box should be cut.
2
 WIRING DIAGRAMS IRD CONNECTION
blue Kl. 8
IRD 1020 black Kl. 1
brown Kl. 20

Ph 220/240V ~
max. 10A rapid
6A slow GW

HS RT

ST
GLT

4 19 3 20 1 2 5 6 21 13 14 15 16 17 18 12 9 10 11 7 8

max. LK max. min.

IS

M M1 PV V1 LW SA
IRD
R

Z UV SV V2
N

HS Mains switch IS Flame ionisation probe

ST Limit thermostat PV Pilot flame gas valve
GW Gas Pressure proving switch SV Start flame gas valve
RT Control thermostat V1 Main flame gas valve
GLT High/low operation thermostat V2 High flame or modulation stage gas valve
M Burner motor LK Air damper motor or actuator
M1 Burner motor for post-purge LW Air pressure proving switch
Z Ignition transformer R Remote reset switch
IRD Infra-red flicker detector SA External lockout signal lamp
UV UV-cell

Program-
display
Start
blue

blue

orange

Sz SV yellow Sz PV

red
Sz V1

green
Betrieb
black

4 19 3 20 1 2 5 6 21 13 14 15 16 17 18 12 9 10 Terminal No.
TMG 740-3

required Input Output

3
COMMISSIONING AND MAINTENANCE 2. Routine Checks

1. Important An inspection of the technical safety of the flame detection

system must be carried out during commissioning of the
The wiring must be checked exactly when commissioning unit as well as after servicing, or if the system has not been
the installation. Incorrect wiring could damage the control in operation over a long period.
box, putting the safety of the burner system at risk.
When mounting and wiring the control box, the applicable For test a), the gas proving switch should be bridged.
installation regulations must be observed.
a) Attempt to start with the hand valve closed:
- The chosen fuse rating must not, on any account, be - After the first safety interval has elapsed
higher than the value listed in the technical data. -> Lockout
- Failure to observe this instruction could, in the case of a b) During normal operation, interrupt detector probe or cut
short circuit, have serious consequences for the control off light:
box or burner system. - In less than 1 sec.
- For safety reasons, it must be ensured that the control -> Lockout
box performs at least one normal shutdown during every
24 hour period.
- Switch off or disconnect the power before plugging in or Fault finding
unplugging the unit.
- Burner control boxes are safety devices and should not Fault finding is considerably simplfied by making use of
be opened. the coloured programme indicator. Irregularities during
commissioning, normal operation or a normal shutdown
pause can be localised via the programme indicator disc.
If a malfunction occurs, it is useful to note the exact position
of the indicator before operating the control switch or reset
button.

The following list is designed to assist with fault finding.

COLOUR WHERE WHAT REASON

BLUE beginning doesn’t start - no power, break in control circuit, air proving switch not in
resting position
continuous ventilation - end switch "MAX" air damper doesn’t operate
line lockout - air proving switch doesn’t switch over or is too late
end continuous ventilation - end switch "ignition position", air damper doesn’t operate
anywhere lockout - stray light

YELLOW end lockout - flame establishment pilot or start valve impossible no

flame signal current or too weak (min. 2 LED’s) flame
detector selector switch set incorrectly

RED end lockout - no flame signal current or too weak after end of second
safety interval (double fuel feed burner)

GREEN end lockout - loss of flame during operation, air pressure too low

BLACK end lockout - stray light due to burning on, UVZ sensor tube reached end
of life and activates shutoff, defect in flame detector circuit

A test baseplate is available for checking the burner control box functions (model designation UP 7520, item no. 18601)
TMG 740-3

4
 BURNER 1- OR 2-STAGE

Ph 220/240V ~
max. 10A rapid
GW
6A slow

HS RT

ST
GLT

4 19 3 20 1 2 5 6 21 13 14 15 16 17 18 12 9 10 11 7 8

max. LK max. min.

IS

M M1 V1 LW SA
IRD
R

Z UV V2
N

BURNER WITH START-VALVE

Ph 220/240V ~
max. 10A rapid GW
6A slow

HS RT

ST
GLT

4 19 3 20 1 2 5 6 21 13 14 15 16 17 18 12 9 10 11 7 8

max. LK max. min.

IS

M M1 LW SA
IRD V1
R

Z UV SV V2
N

2 NOZZLE BURNER

Ph 220/240V ~
max. 10A rapid
GW
6A slow

HS RT

ST
GLT

4 19 3 20 1 2 5 6 21 13 14 15 16 17 18 12 9 10 11 7 8

max. LK max. min.

IS

M M1 PV V1 LW SA
IRD
R
TMG 740-3

Z UV V2
N

5
 SCHEMATIC DIAGRAMM
10A
PH ts 1
GAS ST AIR
HS ts 3
RT
20 9 10 17 18 16 ts 2

I rm1
A
II
B
rs1 13 C
D
G1 14 E
NTC1 - G rm2
RM F
+ C2 C
3 G
RF 18 2 H
L N 15 I
1 5
B R5 R6 K
7 8 E A F
rf3 L
16
9 M
R1 R2 rs2 D rf1 P rm3 N
S O
P
12 I
D1 Q
rf2 K M r t
C1 bl blau or gb rot gn sw
10 R3 R4 Sy
11 17
O M ts1 = Pilot valve safety interval
SA
R
RS
Q
ts2 = Start valve safety interval
ts3 = Main valve 1 safety interval
1 7 11 8 21 5 6 2 19 14 15 4 12 13 3

max.

min.
max.

UV SA GL
IS LM
R M I = cut for monitoring of the iguition spork
V2 SV V1 PV M BM M BM Z
N
II = cut for additional switch contacts

TMG 740-3 WITH SOCKET UVZ 780 WITH SUPPORT

ø 22
395
120

PG 11
138
42 96
75
25

30.5

ø22
102
26

102

80 Cable entry plate

M4 earth tag

r 40
51

22

30
4
8
28
102

80
51

36 10
M4 48

underside cable entry reset switch position

ORDERING INFORMATION
ITEM DESIGNATION ITEM NO.
Burner control box Type TMG 740-3 Mod. 32-32 08211
Socket Socket TMG 70205
Insert plate PG-plate 70502
optional Cable entry plate 70501
Flame detector UVZ 780 white 18814
or UVZ 780 blue 18812
or UVZ 780 red 18813
Flame detector IRD 820 16201
Flame detector IRD 1020 end-on viewing 16522
Flame detector IRD 1020 side-on left 16523
Flame detector IRD 1020 side-on right 16521
IRD mounting flange IRD Holder M93 59093
Flame detector cable 3-wire, 0.6 m 7236001
The above ordering information refers to the standard version.
Special versions are also included in our product range. Specifications subject to change without notice.

TMG 740-3 A Honeywell Company Satronic AG

Brüelstrasse 7
Postfach 324
6
CH-8157 Dielsdorf