Automatic Aeroponic Irrigation System Based On Arduino's Platform

Journal of Physics: Conference Series
PAPER • OPEN ACCESS Related content

- DEVICES FOR OBSERVATORY
Automatic aeroponic irrigation system based on AUTOMATION
R. K. Honeycutt, B. R. Adams, D. J.
Arduino’s platform Swearingen et al.
- Automation and Monitoring Smart Kitchen

Based on Internet of Things (IoT)
To cite this article: A P Montoya et al 2017 J. Phys.: Conf. Ser. 850 012003 F Nugroho and A B Pantjawati
- Real time fish pond monitoring and

automation using Arduino
Z. Harun, E. Reda and H. Hashim
View the article online for updates and enhancements.
This content was downloaded from IP address 2.136.83.89 on 03/04/2019 at 14:18

5th Colombian Conference of Engineering Physics (V CNIF) IOP Publishing
IOP Conf. Series: Journal of Physics: Conf. Series 1234567890
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
Automatic aeroponic irrigation system based on

Arduino’s platform
A P Montoya, F A Obando, J G Morales and G Vargas
Universidad Nacional de Colombia, Medelln, Colombia. Calle 59A N63-20, Bloque 58
E-mail: apmontoy@unal.edu.co
Abstract. The recirculating hydroponic culture techniques, as aeroponics, has several

advantages over traditional agriculture, aimed to improve the efficiently and environmental
impact of agriculture. These techniques require continuous monitoring and automation for
proper operation. In this work was developed an automatic monitored aeroponic-irrigation
system based on the Arduino’s free software platform. Analog and digital sensors for measuring
the temperature, flow and level of a nutrient solution in a real greenhouse were implemented.
In addition, the pH and electric conductivity of nutritive solutions are monitored using the
Arduino’s differential configuration. The sensor network, the acquisition and automation system
are managed by two Arduinos modules in master-slave configuration, which communicate one
each other wireless by Wi-Fi. Further, data are stored in micro SD memories and the information
is loaded on a web page in real time. The developed device brings important agronomic
information when is tested with an arugula culture (Eruca sativa Mill). The system also could
be employ as an early warning system to prevent irrigation malfunctions.
1. Introduction
Aeroponics is a culture technique where the plant roots are suspended in the air and they
are intermittently sprayed with a nutrient solution. This technique has been used both in
research and crops commercial production [1, 2, 3, 4, 5]. Aeroponics presents great advantages
over traditional agriculture, like reduced the consumption of water and nutrients, increased of
growth rate, plant density and therefore crop productivity [6, 2, 7]. Its main disadvantage is
crop susceptibility to electrical faults of the irrigation system [8, 7].
To optimize resources consumption and root’s oxygenation [5], the nutrient solution is
applied intermittently and recirculated, therefore it is necessary to continuously monitoring
the consumption and level of the nutrient solution, as well as the correct operation of pumps
and valves, because a system failure could cause crop loss, due to the lack of substrate of plants.
It is also fundamental in this hydroponic systems monitoring the temperature, pH and electrical
conductivity of the nutrient solution, since these variables are determinant in the nutrition of
the crop.
Some work has been done on this regard. Reyes et al. [9], proposed the development of
a monitoring and control system based on wireless communication protocol Xbee. In that
article there is not a description of the materials and methodology used to develop the proposed
irrigation system, which is based on the relative humidity within the root humidity-chamber.
On the other hand, It has been some advances in the automation, monitoring and control of
the nutritive solution in the production of potatoes seeds in aeroponic systems, providing roots
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution
of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
Published under licence by IOP Publishing Ltd 1
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
with water and nutrients independently, using ultrasonic actuators for nutrients and sprinklers
for water supply [10].
There are different automation solutions that can be used in aeroponic irrigation system,
although its functionality is limited and costs and maintenance are high [11]. Designs that
involves the use of open source software and hardware is an economical alternative for the
development of automatic monitoring and control systems. Arduino is today one of the most
popular open platforms used to obtain a large number of applications [12]. Recent applications
in the agricultural area use Arduino as a platform for the development of control systems. Bitella
et al. [13], Ferrarezi et al. [14], and Siva [15] worked in an automatic irrigation systems in soil
cultivation. While Bajer & Krejcar [16], and Groener et al. [17], implemented a monitoring and
control system for a greenhouse operation. Regarding aeroponics, Jonas et al. [18], developed an
automatic monitoring system to control the environmental and irrigation conditions of a small
aeroponic chamber using Arduino. The system controls the irrigation frequency based on the
root chamber moisture. All the information is send to a web server and share in Twiter.
In the literature review it was not possible to find information related to the implementation of
low cost systems for monitoring pH and electrical conductivity of hydroponics nutrient solution.
There is a generalized lack of information in scientific literature related with the monitoring and
automation of hydroponic irrigation systems.
This paper presents the construction of a low cost system for monitoring and automating
the aeroponic irrigation of a greenhouse research facility. In addition to automate the irrigation
frequency several variables associated with the nutrient solution and the proper functioning
of the irrigation system are monitored, like the pH and electrical conductivity of the nutrient
solution. The information provided by the system is stored in microSD memory and it can be
accessed in real time by an Internet web server and Bluetooth.
2. Materials y methods
2.1. Irrigation system hardware
2.1.1. Greenhouse aeroponic system The implementation was carried out in a chapel-
greenhouse facility with an area of 16x8m, average height 4m, built in steel structure and anti-
drip thermal plastic gauge 6. The greenhouse has roller side windows activated by gearmotors.
The facilities are located at 6.26, -75.57, altitude 1469 m.s.n.m, Medellin-Colombia.
The measurement of external climatic variables was performed with a weather station (Davis
Vantage Pro 2). While the internal monitoring has been made using self-made aspiration thermo-
higrometers.
The greenhouse has nine aeroponic-recirculating growing beds, with dimensions of 1x6m and
maximum capacity of 2000 plants each. The beds were built in aluminum, black plastic and
expanded polystyrene gauge 6 (EPS). Each bed has a hydraulic pump, nutrient solution tank
and independent recirculation system, which included filters and 24 sprinkles (0.0097 sl ) each
one. The diagram of the hydraulic system of two of the beds can be seen in Figure 1.
Due it was available only one pH sensor and one EC sensor, normally open and closed solenoid
valves were used to make independently measurements of these variables for each bed.
2.1.2. Arduino’s modules For monitoring and automating the irrigation of the aeroponic
system, two Arduino Mega modules in master-slave configuration were used. They were packaged
on PVC boxes with external connectors for instrumentation and communications. The master
module is used for storing data in a microSD memory, it is also in charge of microclimatic data
adquisition, Wi-Fi and Ethernet communications. The Arduino-slave was used for monitoring
and automation of the irrigation system, it is also saved their own information in a microSD
memory and is in charge of the bluetooth comunication. The devices used in the implementation
can be appreciate in the connection diagram in Figure 2.
2
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
Figure 1. Implementation diagram.
Figure 2. Detailed Master-Slave connection diagram.
Independent power sources of 12V and 5V, 6 and 4A respectively, were used to power all the
sensors and solenoid valves. The hydraulic pumps were connected to 110 VAC.
Table 1 detailed the measured variables and sensors used in this implementation.
3
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
Table 1. Implemented sensors and measured variables.

Measure variable Sensor Sensor principle Calibration curve
Nutritive solution temperature LM35 Solid state T = 113.1v − 7.8593
Level HC-SR04 Ultrasound Level = 0.0003V 2 − 0.3058lt
Flow YF-S201 Hall effect
Pump electric current ACS-71 Hall effect
Electrical conductivity HI3001 Potentiometric EC = 4960.3v − 1359.1
pH HI1001 Electrolytic pH = 6.383v − 1.1702
2.1.3. Instrumentation The nutritive solution temperature sensors were protected on

aluminum-PVC probes, as shown in Figure 3. These probes were immersed into the storage
bins, looking that the sensor was completely sealed. The probes were calibrated using analogous
bulb thermometers as pattern. The resulting calibration equation can be seen in Table 1, were T
is te temperature in Celsius degrees and v is the voltage output of the sensors, given in millivolts.
Figure 3. Implemented monitoring system.
The ultrasonic level sensors were installed on top of the storage bins. These were calibrated
by measuring with a ruler and volumetric pattern of one liter. The resulting calibration equation
is shown in Table 1, were V is the volume of nutritive solution given in liters and Level is the
actual level in cm.
The flow sensor was located in the pipe between the pump and the sprinklers. This sensor
is pre-calibrated and the calibration curve was verified through timed volumetric measurement.
The sensor was connected to the Arduino by one of the serial ports.
The electric current measurement is used to monitoring the proper functioning of the
irrigation system. Through this variable is establishing the energy consumption of the hydraulic
pump for each growing bed, verify the irrigation frequency and the proper functioning of the
4
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
pumps. When the pump is working correctly the electric current oscillates around 2.42 - 2.18
A. When the current value is zero indicates that the pumps are off. If the current value exceeds
the standard value, indicates that pump presents problems and should be revised.
The pH and EC sensors were installed in the common pipe of the growing beds. Such
probes were connected to a HI-98143 transmitter, responsible for amplifying signals to 4-20
mA. This signal are adapted to voltage using precision resistors of 110 Ohm, to be acquired
by the Arduino analogs inputs. The resulting voltage signal is differential, so it was necessary
to configure four analog Arduino’s inputs as differential inputs. To achieved this, Arduino’s
microcontroller registers were modified using AVR-C language, resulting in a library that allows
analog data acquisition in differential mode with an adjustable gain between 10-200.
Since the measurement of pH and EC do not performed continuously and the probes most
remained always submerged, the measurement routine included a process of pipe pre-cleaning
with nutrient solution. After the measurement, the pipes and the three-way manifold, where
sensors were installed, is washing and filling with clean water until the next measurement.
The probes were calibrated using pH and conductivity buffer solutions. The accuracy of
the measurements was tested against a pH and EC meter using nutritive solutions at different
concentrations. The obtained calibration equations can be seen in Table 1, where pH and EC are
the values of pH and electrical conductivity (uS/cm2 ) and v is the voltage value received in the
differential pins of Arduino. The pH and EC electrodes were calibrated weekly to ensure proper
operation and service. The measurements of these variables were temperature compensated.
2.1.4. Acting system This system includes four solenoid valves per growing bed, three valves are
normally closed and one is normally open, as can be seen in Figure 4. In addition a hydraulic
pump of 21 HP, 36 min l
flow and a maximum hydraulic head of 36 m is used. Besides, four
electro-valves were used in the measurement and cleaning routine.
Figure 4. Aeroponic irrigation system actuators assembly.
All actuators were powered through a 16 channel relay module, which is connected to the
00
digital outputs of slave Arduino. Plastic low pressure 12 diameter, 12 V - 0.5 A, solenoid valves
were driven directly by the relay module, while the pumps were activated using additional
contactors of 110 VAC. In Figures 1 and 4 it can be appreciate the detail of the devices that
make up the system. Keeping in mind that not all elements are installed in the same place, for
clarity the diagram of the process of the irrigation system is detailed in Figure 2.
5
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
2.1.5. Comunication Through bluetooth protocol may it access the information from the
sensors and performing the test automation using the slave peripheral bluetooth module HC-05.
This information can be accessed from any device with this kind of communication (phone,
tablet, among others). Communication is established in the 2.4GHz band, with a range between
5 and 10 m away.
Master-Slave communication located 9m away one each other is done wirelessly via Wi-Fi.
The wireless network is composed by two devices with password protected and has a range
of 15-20m. The slave sends information related to the irrigation system. This data is stored
redundantly in a 2GB microSD memory on the slave device, while the master store the same
information besides the greenhouse climate data.
Theremore, the master device is connected to internet by Ethernet Industrial Protocol using
the W5100 module. Information on climatic variables and irrigation is loaded to the website:
http://168.176.108.50:4025, with a sampling rate of one minute. This information could be
accessed from anywhere with Internet access. The Figure 5 shows a screenshot of the mentioned
website, where it can be appreciate climatic and irrigation information in addition to alarm
indicators.
Figure 5. Web page screenshot.
2.2. Arduino’s software

In the master module was programmed routines for climate data acquisition, wireless
communication, microSD memory storage and publication of data on the web. Whereas, in the
slave device was programmed the same routines, except the web page publication one. Additional
routines for irrigation and measuring EC and pH were programmed. The flow diagram of the
main routine of both modules can be seen in Figure 6.
In the slave module was programmed diurnal and nocturnal irrigation frequency for each
growing bed. The irrigation frequency is synchronized with the data acquisition , so when an
irrigation cycle is performed the data are save in the microSD and send to the master module
along with the acquisition time given by the Real Time Clock module.
They were also scheduled three alarms to alert system malfunction. The Alarm of the nutrient
solution ending is activated when the liquid level in the storage tank reaches a minimum value
(5 cm). The Alarm for the clogged sprinklers is activated when there is more than 4 sprinklers
6
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
Figure 6. Main program flow diagram of master and slave modules.
plugged on a bed, an then the flow supplied by the pump is below minimum value. Finally, the
alarm for the shutdown system is activated when a pump is activated and the pumped flow is
zero. Indirectly it is possible to know electricity failures or Internet connection malfunction, if
a pump is not active for long time or when the information on the website is not updated every
minute. In Figure 5, it can be seen a detail of these alarms.
2.3. System test

An arugula crop (Eruca sativa Mill) was used to tests the implemented irrigation system. It
was stablished a seedbed with 300 arugula seeds, planted in individual plastic containers with
pine sawdust substrate. The plants were transplanted to the aeroponic beds at cotyledon state,
when it was observed that the root protruded of the container (five days after seeding). System
performance was recorded for 60 days between the months of May to July 2016.
The tests were performed on two beds, one with the arugula crop and the other one totally
seal without crop. The irrigation frequency was established in 15 seconds turned on by 400
seconds turned off, using a modified Hoagland nutrient solution, diluted 50% with EC between
uS
1200-1500 cm 2 and pH between 5.5-6.5, measured at the preparation time. The diluted Hoagland
nutrient solution was change one week after transplant for a full one, with EC and pH between
uS
5.5-6.5 and 2100-2500 cm 2 , respectively, measured at preparation time. The nutrient solutions
were manually prepared for each bed. The tanks were filled with 90 L of nutrient solution,
equivalent to 31 cm in their respective bins. Independent tests were performed to monitor the
consumption of the solution and the evolution of EC, pH, temperature solution, flow and pump
electrical current in both beds.
3. Results y discussion
The external and internal climatic conditions during the test are show in Figure 7. The maximum
and minimum internal temperature were 44 °C and 17 °C respectively, while the relative humidity
was between 9-100 %.
Figure 8 shows a the nutrient solution consumption in the two beds during 78 hours of
continuous operation. The identical tanks were filled with 87 L of nutritive solution. The
minimum level was set at 27 L,to prevent plants lost. Both growing beds were totally sealed
7
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
Figure 7. Climatic condition during five test days.
except for the holes where the plants are located. The bed without plants decreased their
nutrient solution level due to evaporation, while in the growing bed with crop, the consumption
of the solution is due to evapotranspiration. Subtraction of both consumptions results in crop
transpiration for each time instant.
The total evaporation during the 78 h test was 11.91 L, while the evapotranspiration was 63.12
L, resulting in a crop transpiration of 51.07 L during the 78 h. The resulting individual plant
transpiration was 2.18 mL h . As expected, the greatest changes in evaporation occur during the
day, which have higher temperatures and lower humidities. To avoid interfering with the nutrient
solution consumption monitoring trials, independent tests for monitoring EC, pH, temperature
and flow were made.
In Figure 9, at 9:30am of the first day, it can be see the change of the old Hoagland nutritive
solution for a new one. The old solution (half Hoagland) were replaced with 90 L of a complete
Hoagland solution for the bed with crop (pH 6). The other bed is running with tap water (pH
7).
It can be seen that the first measurement after the solution change, has a pH of 6.3, this
value is due to the traces of the old nutritive solution in the pipes, so both pH values are slightly
above of the the actual value at the time of the preparation. Small variations in pH are seen
during the test, showing slight increases during the day and a tendency to increase the pH of
the solution as it is consumed.
Regarding the electrical conductivity of the nutritive solution, in the Figure 10 is possible
to appreciate the moment of the solution change, from a diluted Hoagland solution (50%),
uS uS
with conductivity 1400 cm 2 , for the complete solution (100%) with 2500 cm2 . Due to the
8
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
Figure 8. Nutritive solution consumption comparison during 78 h. For a growing bed without
plants (blue) and a bed with 300 plants (red). The green line represents the crop transpiration.
Figure 9. Nutritive solution pH comparison for a growing bed without plants (blue) and a bed
with 300 plants (red).
uS
instrument accuracy (200 cm2
), it was not possible to conclude about the variations of that
9
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
variable throughout the day, but it is possible to establish that there is a tendency to increase
the conductivity of the nutrient solution during the test in the crop bed.
Figure 10. Nutritive solution EC comparison for a growing bed without plants (blue) and a
bed with 300 plants (red).
The results of temperature measurements are presented in Figure 11. It can be appreciated
that the temperature of the nutritive solution of the bed with crop has a mean temperature
of 25 ◦ C, while the bed without crop has a mean of 24 ◦ C. The LM35 temperature sensor has
an accuracy of ±1 ◦ C, so that it is possible to consider that both values are the same and the
temperature of the solution remains relatively constant throughout the experiment.
Figure 11. Nutritive temperature solution comparison for a growing bed without plants (blue)
and a bed with 300 plants (red).
10
850 (2017) 012003 doi:10.1088/1742-6596/850/1/012003
4. Conclusions
The automatic monitored aeroponic-irrigation system based on the Arduino free software
platform present good performance when it is implemented in a research greenhouse. This results
can be applied in a commercial greenhouse with polyculture or when different nutrient solutions
formulation are employed. For this particular application the most difficult implementation task
lies in the fact of having just one EC and pH probes for monitoring different nutrient solutions.
In a commercial application, such difficulty is eliminated, since these systems only has a central
tank of nutrient solution, therefore, the measurements can be realized continuously.
Arduino platform can be used as a data acquisition system for differential output sensors like
EC and pH probes, using the differential configuration showed here, reducing the cost of such
implementations.
The deployment of information and alarms on a website is very useful, allowing to take
appropriate control irrigation actions to avoid crop loss.
It is considered relevant for future work automatically send alarm signals directly to the
final user of the system through mobile devices. In addition, there is a desirable to develop a
complementary automatic system to prepare the nutrient solution based on the EC and pH.
References
[1] Komosa A, Kleiber T and Markiewicz B 2014 Acta Sci. Pol., Hortorum Cultus 13 163–177 ISSN 1644-0692
[2] Lakkireddy K, Kasturi K and Sambasiva Rao K R S 2012 Research & Reviews: . . . 1 26–35 ISSN
2278 2206 URL http://stmjournals.com/sci/index.php?journal=RRJoAST{\&}page=article{\&}op=
view{\&}path[]=50
[3] Mbiyul M W, Muthoni J, Kabiral J, Elmar G, Muchiral C, Pwaipwail P, Ngaruiyal J, Otienol S and Onditil J
2012 Journal of Horticulture and Forestry 4 172–177 URL http://www.academicjournals.org/journal/
JHF/article-abstract/C5947BF2821
[4] Nir I 1981 Growing Plants in Aeroponics Growth System
[5] Peterson L A and Krueger A R 1988 Crop Science 28 712–713 ISSN 1098-6596 (Preprint arXiv:1011.1669v3)
[6] Chiipanthenga M, Maliro M, Demo P and Njoloma J 2012 African Journal of Biotechnology 11 3993–3999
[7] Putra P A and Yuliando H 2015 Agriculture and Agricultural Science Procedia 3 283–288 ISSN 22107843
URL http://www.sciencedirect.com/science/article/pii/S2210784315000558
[8] Carruthers S 1992 Practical Hydroponics & Greenhouses
[9] Reyes J L, Montoya R, Ledesma C and Ramı́rez R 2012 Acta Horticulturae 947 153–156 ISSN 05677572
[10] Idris I and Sani M I 2012 Proceedings of 2012 IEEE Conference on Control, Systems and Industrial
Informatics, ICCSII 2012 120–125
[11] Gaddam A, Al-Hrooby M and Esmael W F 2014 Designing a Wireless Sensors Network for Monitoring and
Predicting Droughts Proceedings of the 8th International Conference on Sensing Technology pp 210–215
ISSN 21568073
[12] Mesas-Carrascosa F, Verdú Santano D, Meroño J, Sánchez de la Orden M and Garcı́a-Ferrer A 2015
Biosystems Engineering 137 73–83 ISSN 15375110 URL http://www.sciencedirect.com/science/
article/pii/S1537511015001208
[13] Bitella G, Rossi R, Bochicchio R, Perniola M and Amato M 2014 Sensors (Switzerland) 14 19639–19659
ISSN 14248220
[14] Ferrarezi R S, Dove S and Van Iersel M W 2014 A Low Cost, Arduino-based System for Monitoring and
Controlling Substrate Water Content 2014 ASHS Annual Conference
[15] Siva Kumar P, Jilani S A K and Venkata Raman B 2015 International Journal of Advanced Research in
Electronics and Communication Engineering (IJARECE) 4
[16] Bajer L and Krejcar O 2015 IFAC-PapersOnLine 48 368–373 ISSN 24058963 URL http://www.
sciencedirect.com/science/article/pii/S240589631500837X
[17] Groener B, Knopp N, Korgan K, Perry R, Romero J, Smith K, Stainback A, Strzelczyk A and Henriques
J 2015 Procedia Engineering 107 470–479 ISSN 18777058 URL http://dx.doi.org/10.1016/j.proeng.
2015.06.105
[18] Jonas P, Maskara A, Salguero A and Truong A 2015 Garduino: A Cyber-Physical Aeropon-
ics System (Preprint arXiv:1011.1669v3) URL http://ecal.berkeley.edu/files/ce186/projects/
truonganders{\_}4941954{\_}63829747{\_}Garduino-1.pdf
11

Automatic Aeroponic Irrigation System Based On Arduino's Platform

Uploaded by

Copyright:

Available Formats

Automatic Aeroponic Irrigation System Based On Arduino's Platform

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Automatic Aeroponic Irrigation System Based On Arduino's Platform

Uploaded by

Copyright:

Available Formats

Journal of Physics: Conference Series

PAPER • OPEN ACCESS Related content

- Automation and Monitoring Smart Kitchen

- Real time fish pond monitoring and

This content was downloaded from IP address 2.136.83.89 on 03/04/2019 at 14:18

Automatic aeroponic irrigation system based on

Abstract. The recirculating hydroponic culture techniques, as aeroponics, has several

Figure 1. Implementation diagram.

Figure 2. Detailed Master-Slave connection diagram.

Table 1. Implemented sensors and measured variables.

2.1.3. Instrumentation The nutritive solution temperature sensors were protected on

Figure 3. Implemented monitoring system.

Figure 4. Aeroponic irrigation system actuators assembly.

Figure 5. Web page screenshot.

2.2. Arduino’s software

Figure 6. Main program flow diagram of master and slave modules.

2.3. System test

Figure 7. Climatic condition during five test days.

You might also like