Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
62 views

Lab Handout 3 PDF

This lab handout provides instructions for students to verify Ohm's Law by measuring the current and resistance of different resistors using a digital multimeter and calculating resistance using Ohm's Law. Students are asked to find the nominal resistance of each component using color codes, measure the current through each resistor, calculate the resistance using Ohm's Law, and record their results in a table to calculate the percentage deviation from the nominal value. The handout also includes review questions about breadboards, current measurement devices, and how resistance and current are affected by changes in wire cross-section and circuit resistance.

Uploaded by

Sahab
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
62 views

Lab Handout 3 PDF

This lab handout provides instructions for students to verify Ohm's Law by measuring the current and resistance of different resistors using a digital multimeter and calculating resistance using Ohm's Law. Students are asked to find the nominal resistance of each component using color codes, measure the current through each resistor, calculate the resistance using Ohm's Law, and record their results in a table to calculate the percentage deviation from the nominal value. The handout also includes review questions about breadboards, current measurement devices, and how resistance and current are affected by changes in wire cross-section and circuit resistance.

Uploaded by

Sahab
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Mehran University of Engineering and Technology, Jamshoro

Department of Telecommunication Engineering


Applied Physics (1st Semester, 1st Year)
______________________________________________________________________________
Name: _____________________________________ Roll Number: ____________________
Score: _____________ Signature: ________________________Date:____________________

LAB HANDOUT #03


OHM’S LAW VERIFICATION

OBJECTIVE: Verification of Ohm’s Law & determine the resistance of resistor


using:
(a) Ohms law and,
(b) Digital Multimeter.

EQUIPMENT & CIRCUIT COMPONENTS REQUIRED:


 Breadboard
 Digital Multimeter
 DC Power Supply
 Resistors with different ratings
 Connecting wires

THEORY:

Method I: Calculating resistance through Ohm Meter or Digital Multimeter

An ohmmeter is an electrical instrument that measures electrical


resistance, the opposition to an electric current. Micro-
ohmmeters (microhmmeter or micro ohmmeter) make low
resistance measurements. Megohmmeters (aka mega ohmmeter
or in the case of a trademarked device Megger) measure large
values of resistance. The unit of measurement for resistance is
ohms (Ω).

Steps:
• Put one probe on one end of the resistor
• Put the other probe on the other end of the resistor
• Read the ohm meter scale

PROCEDURE:
You will be supplied with sets of 3 resistors.
1. Find the nominal value and the tolerance of each
resistance using the Resistor color code chart.
2. Using the digital multimeter as an Ammeter,
measure and record the current accross each
Mehran University of Engineering and Technology, Jamshoro
Department of Telecommunication Engineering
Applied Physics (1st Semester, 1st Year)
______________________________________________________________________________
Resistor.
3. Connect the circuit and perform the following :
a- Set the source voltage Vs to 09 V.
b- Measure V and I.
c- Repeat steps 3a and 3b for the remaining resistors.
d- Record your results in Table.

EXERCISE TABLE:

Resistor R1 (KΩ) R2(KΩ) R3(KΩ)

Nominal value/Tolerance

Ammeter reading

Current via Ohm’s Law

%Deviation from nominal value

Review Questions:

Q1. What is the difference between Bread-board and Vero-board?

_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________

Q2. Which device is used to measure the current in the circuit?


_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________

Q3. What will happen with the current if the cross section of wire is increased?
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
Mehran University of Engineering and Technology, Jamshoro
Department of Telecommunication Engineering
Applied Physics (1st Semester, 1st Year)
______________________________________________________________________________
Q4. What will happen with the current if the resistance in a circuit with constant voltage
increases?
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________
_____________________________________________________________________________________

FINAL CHECK LIST

1. Return all equipment and material to their proper storage area


2. Submit your answers to questions, and results before the next laboratory

You might also like