Cutmaster A60: Operating Manual

60 208-
230V 400V 460V 600V
CUTMASTER® A60
AUTOMATED PLASMA CUTTING SYSTEM
Operating
Manual
Art # A-08952_AD
Revision: AU Issue Date: October 24, 2014 Manual No.: 0-4981
VictorThermalDynamics.com
WE APPRECIATE YOUR BUSINESS!
Congratulations on your new Victor Thermal Dynamics product. We are proud to have you as our
customer and will strive to provide you with the best service and reliability in the industry. This product
is backed by our extensive warranty and world-wide service network. To locate your nearest distributor
or service agency call 1-800-426-1888, or visit us on the web at www.VictorThermalDynamics.com.
This Operating Manual has been designed to instruct you on the correct use and operation of your
Victor Thermal Dynamics product. Your satisfaction with this product and its safe operation is our
ultimate concern. Therefore please take the time to read the entire manual, especially the Safety Pre-
cautions. They will help you to avoid potential hazards that may exist when working with this product.
YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and Fabricators Worldwide.
Victor Thermal Dynamics is a Global Brand of manual and automation Plasma Cutting Products for
Victor Technologies.
We distinguish ourselves from our competition through market-leading, dependable products that
have stood the test of time. We pride ourselves on technical innovation, competitive prices, excel-
lent delivery, superior customer service and technical support, together with excellence in sales and
marketing expertise.
Above all, we are committed to developing technologically advanced products to achieve a safer
working environment within the welding industry.
! WARNING
Read and understand this entire Manual and your employer’s safety practices before installing, operat-
ing, or servicing the equipment.
While the information contained in this Manual represents the Manufacturer's best judgement, the
Manufacturer assumes no liability for its use.
Plasma Cutting Power Supply

CutMaster® A60
SL100 ™ SV Automated Torch
Operating Manual Number 0-4981
Published by:
Victor Technologies International, Inc.
82 Benning Street
West Lebanon, New Hampshire, USA 03784
(603) 298-5711
www.victorthermaldynamics.com
Copyright 2008, 2009, 2010, 2011, 2012, 2013, 2014by

Victor Technologies International, Inc.
All rights reserved.
Reproduction of this work, in whole or in part, without written permission of the pub-
lisher is prohibited.
The publisher does not assume and hereby disclaims any liability to any party for any
loss or damage caused by any error or omission in this Manual, whether such error
results from negligence, accident, or any other cause.
Original Publication Date: January 7, 2008

Revision Date: October 24, 2014
Record the following information for Warranty purposes:
Where Purchased:____________________________________________
Purchase Date:_______________________________________________
Power Supply Serial #:_________________________________________
Torch Serial #:_______________________________________________
i
TABLE OF CONTENTS
SECTION 1: GENERAL INFORMATION................................................................... 1-1
1.01 Notes, Cautions and Warnings......................................................................... 1-1
1.02 Important Safety Precautions.......................................................................... 1-1
1.03 Publications..................................................................................................... 1-2
1.04 Note, Attention et Avertissement...................................................................... 1-3
1.05 Precautions De Securite Importantes.............................................................. 1-3
1.06 Documents De Reference................................................................................ 1-5
1.07 Declaration of Conformity................................................................................ 1-6
1.08 Statement of Warranty..................................................................................... 1-7
SECTION 2 SYSTEM: INTRODUCTION .................................................................. 2-1
2.01 How To Use This Manual................................................................................. 2-1
2.02 Equipment Identification.................................................................................. 2-1
2.03 Receipt Of Equipment...................................................................................... 2-1
2.04 Power Supply Specifications........................................................................... 2-2
2.05 Input Wiring Specifications.............................................................................. 2-3
2.06 Power Supply Features.................................................................................... 2-4
SECTION 2 TORCH: INTRODUCTION ................................................................... 2T-1
2T.01 Scope of Manual.............................................................................................2T-1
2T.02 General Description........................................................................................2T-1
2T.03 Specifications ................................................................................................2T-1
2T.04 Options And Accessories................................................................................2T-2
2T.05 Introduction to Plasma...................................................................................2T-2
SECTION 3 SYSTEM: INSTALLATION .................................................................... 3-1
3.01 Unpacking........................................................................................................ 3-1
3.02 Lifting Options................................................................................................. 3-1
3.03 Power Supply location and Mounting.............................................................. 3-1
3.04 Opening the Contactor Cover........................................................................... 3-1
3.05 Primary Input Power Connections................................................................... 3-2
3.06 Gas Connections.............................................................................................. 3-4
SECTION 3 TORCH: INSTALLATION..................................................................... 3T-1
3T.01 Torch Connections..........................................................................................3T-1
3T.02 CNC Connection..............................................................................................3T-1
3T.03 Setting Up Automation or Machine Torch.......................................................3T-3
SECTION 4 SYSTEM: OPERATION........................................................................ 4-1
4.01 Front Panel Controls / Features........................................................................ 4-1
4.02 Preparations for Operation............................................................................... 4-2
TABLE OF CONTENTS
SECTION 4 TORCH: OPERATION......................................................................... 4T-1
4T.01 Machine and Automated Torch Operation.......................................................4T-1
4T.02 Automation Torch Parts Selection...................................................................4T-2
4T.03 Machine and Hand Torch Parts Selection........................................................4T-2
4T.04 Cut Quality......................................................................................................4T-3
4T.05 General Cutting Information............................................................................4T-4
4T.06 Hand Torch Operation.....................................................................................4T-4
4T.07 Gouging..........................................................................................................4T-8
4T.08 Recommended Cutting Speeds for Machine and Automated Torches
With Exposed Tip..........................................................................................4T-10
4T.09 Recommended Cutting Speeds for Machine and Automated Torches
With Shielded Tip..........................................................................................4T-28
PATENT INFORMATION.................................................................................. 4T-46
SECTION 5 SYSTEM: SERVICE............................................................................ 5-1

5.01 General Maintenance....................................................................................... 5-1
5.02 Maintenance Schedule..................................................................................... 5-2
5.03 Common Faults................................................................................................ 5-2
5.04 Fault Indicator.................................................................................................. 5-3
5.05 Basic Troubleshooting Guide........................................................................... 5-4
5.06 Circuit Fault Isolation....................................................................................... 5-6
SECTION 5 TORCH: SERVICE............................................................................ 5T-1
5T.01 General Maintenance......................................................................................5T-1
5T.02 Inspection and Replacement of Consumable Torch Parts...............................5T-2
SECTION 6: PARTS LISTS................................................................................. 6-1
6.01 Introduction..................................................................................................... 6-1
6.02 Ordering Information....................................................................................... 6-1
6.03 Power Supply Replacement............................................................................. 6-1
6.04 Replacement Power Supply Parts.................................................................... 6-2
6.05 Options and Accessories................................................................................. 6-2
6.06 Torch Replacement Parts SL100SV Torch (w/Solenoid on Mounting Tube)..... 6-3
6.07 Torch Consumable Parts Automation / Machine (SL100)Torch........................ 6-5
6.08 Torch Consumable Parts Manual (SL60)Torch................................................. 6-6
6.09 Replacement Parts for Hand Torch ................................................................. 6-7
TABLE OF CONTENTS
APPENDIX 1: SEQUENCE OF OPERATION (BLOCK DIAGRAM)....................................... A-1
APPENDIX 2: DATA TAG INFORMATION.................................................................. A-2
APPENDIX 3: TORCH PIN - OUT DIAGRAMS............................................................ A-3
APPENDIX 4: TORCH CONNECTION DIAGRAMS........................................................ A-4
APPENDIX 5: SYSTEM SCHEMATIC, 208/460V UNITS................................................. A-6
APPENDIX 6: SYSTEM SCHEMATIC, 400V/600V UNITS............................................... A-8
APPENDIX 7: RAW ARC VOLTAGE .......................................................................A-10
APPENDIX 8: PUBLICATION HISTORY...................................................................A-12

CUTMASTER A60
SECTION 1:
GENERAL INFORMATION GASES AND FUMES
Gases and fumes produced during the plasma cutting process can be
dangerous and hazardous to your health.
1.01 Notes, Cautions and Warnings • Keep all fumes and gases from the breathing area. Keep your
head out of the welding fume plume.
Throughout this manual, notes, cautions, and warnings are used to
highlight important information. These highlights are categorized as • Use an air-supplied respirator if ventilation is not adequate to
follows: remove all fumes and gases.
NOTE • The kinds of fumes and gases from the plasma arc depend on
the kind of metal being used, coatings on the metal, and the
An operation, procedure, or background informa- different processes. You must be very careful when cutting
tion which requires additional emphasis or is help- or welding any metals which may contain one or more of the
ful in efficient operation of the system. following:
Antimony Chromium Mercury
Arsenic Cobalt Nickel
Barium Copper Selenium Beryl-
CAUTION lium Lead Silver
Cadmium Manganese Vanadium
A procedure which, if not properly followed, may
• Always read the Material Safety Data Sheets (MSDS) that should
cause damage to the equipment.
be supplied with the material you are using. These MSDSs
will give you the information regarding the kind and amount of
! WARNING
fumes and gases that may be dangerous to your health.
• For information on how to test for fumes and gases in your
workplace, refer to item 1 in Subsection 1.03, Publications in
A procedure which, if not properly followed, may cause this manual.
injury to the operator or others in the operating area.
• Use special equipment, such as water or down draft cutting
tables, to capture fumes and gases.
• Do not use the plasma torch in an area where combustible or
WARNING explosive gases or materials are located.
Gives information regarding possible electrical shock • Phosgene, a toxic gas, is generated from the vapors of chlo-
injury. Warnings will be enclosed in a box such as this. rinated solvents and cleansers. Remove all sources of these
vapors.
• WARNING: This product contains chemicals, including lead,
1.02 Important Safety Precautions known to the State of California to cause birth defects and other
reproductive harm. Wash hands after handling.
! WARNING ELECTRIC SHOCK

Electric Shock can injure or kill. The plasma arc process uses and
OPERATION AND MAINTENANCE OF PLASMA ARC produces high voltage electrical energy. This electric energy can
EQUIPMENT CAN BE DANGEROUS AND HAZARD- cause severe or fatal shock to the operator or others in the workplace.
OUS TO YOUR HEALTH.
• Never touch any parts that are electrically “live” or “hot.”
Plasma arc cutting produces intense electric and • Wear dry gloves and clothing. Insulate yourself from the work
magnetic emissions that may interfere with the piece or other parts of the welding circuit.
proper function of cardiac pacemakers, hearing • Repair or replace all worn or damaged parts.
aids, or other electronic health equipment. Persons • Extra care must be taken when the workplace is moist or damp.
who work near plasma arc cutting applications • Install and maintain equipment according to NEC code, refer
should consult their medical health professional to item 9 in Subsection 1.03, Publications.
and the manufacturer of the health equipment to • Disconnect power source before performing any service or
determine whether a hazard exists. repairs.
To prevent possible injury, read, understand and follow • Read and follow all the instructions in the Operating Manual.
all warnings, safety precautions and instructions before
using the equipment. Call 1-603-298-5711 or your local
distributor if you have any questions.
FIRE AND EXPLOSION
Fire and explosion can be caused by hot slag, sparks, or the plasma arc.
Manual 0-4981 GENERAL INFORMATION 1-1

CUTMASTER A60
• Be sure there is no combustible or flammable material in the
workplace. Any material that cannot be removed must be
protected. ! WARNING
• Ventilate all flammable or explosive vapors from the workplace. WARNING: This product contains chemicals, including lead, known to
• Do not cut or weld on containers that may have held combus- the State of California to cause birth defects and other reproductive
tibles. harm. Wash hands after handling.
• Provide a fire watch when working in an area where fire hazards
may exist. 1.03 Publications
• Hydrogen gas may be formed and trapped under aluminum
Refer to the following standards or their latest revisions for more
workpieces when they are cut underwater or while using a water
information:
table. DO NOT cut aluminum alloys underwater or on a water
table unless the hydrogen gas can be eliminated or dissipated. 1. OSHA, SAFETY AND HEALTH STANDARDS, 29CFR 1910,
Trapped hydrogen gas that is ignited will cause an explosion. obtainable from the Superintendent of Documents, U.S.
Government Printing Office, Washington, D.C. 20402
2. ANSI Standard Z49.1, SAFETY IN WELDING AND CUTTING,
NOISE obtainable from the American Welding Society, 550 N.W.
LeJeune Rd, Miami, FL 33126
Noise can cause permanent hearing loss. Plasma arc processes can
cause noise levels to exceed safe limits. You must protect your ears 3. NIOSH, SAFETY AND HEALTH IN ARC WELDING AND GAS
from loud noise to prevent permanent loss of hearing. WELDING AND CUTTING, obtainable from the Superintendent
• To protect your hearing from loud noise, wear protective ear
of Documents, U.S. Government Printing Office, Washington,
plugs and/or ear muffs. Protect others in the workplace.
D.C. 20402
• Noise levels should be measured to be sure the decibels (sound) 4. ANSI Standard Z87.1, SAFE PRACTICES FOR OCCUPATION
do not exceed safe levels. AND EDUCATIONAL EYE AND FACE PROTECTION, obtainable
from American National Standards Institute, 1430 Broadway,
• For information on how to test for noise, see item 1 in Subsec- New York, NY 10018
tion 1.03, Publications, in this manual.
5. ANSI Standard Z41.1, STANDARD FOR MEN’S SAFETY-TOE
FOOTWEAR, obtainable from the American National Standards
Institute, 1430 Broadway, New York, NY 10018
PLASMA ARC RAYS
6. ANSI Standard Z49.2, FIRE PREVENTION IN THE USE OF CUT-
Plasma Arc Rays can injure your eyes and burn your skin. The plasma TING AND WELDING PROCESSES, obtainable from American
arc process produces very bright ultra violet and infra red light. These National Standards Institute, 1430 Broadway, New York, NY
arc rays will damage your eyes and burn your skin if you are not 10018
properly protected.
7. AWS Standard A6.0, WELDING AND CUTTING CONTAIN-
• To protect your eyes, always wear a welding helmet or shield. ERS WHICH HAVE HELD COMBUSTIBLES, obtainable from
Also always wear safety glasses with side shields, goggles or American Welding Society, 550 N.W. LeJeune Rd, Miami, FL
other protective eye wear. 33126
• Wear welding gloves and suitable clothing to protect your skin 8. NFPA Standard 51, OXYGEN-FUEL GAS SYSTEMS FOR
from the arc rays and sparks. WELDING, CUTTING AND ALLIED PROCESSES, obtainable
• Keep helmet and safety glasses in good condition. Replace from the National Fire Protection Association, Batterymarch
lenses when cracked, chipped or dirty. Park, Quincy, MA 02269
• Protect others in the work area from the arc rays. Use protective 9. NFPA Standard 70, NATIONAL ELECTRICAL CODE, obtainable
booths, screens or shields. from the National Fire Protection Association, Batterymarch
• Use the shade of lens as suggested in the following per ANSI/ Park, Quincy, MA 02269
ASC Z49.1: 10. NFPA Standard 51B, CUTTING AND WELDING PROCESSES,
Minimum Protective Suggested obtainable from the National Fire Protection Association, Bat-
Arc Current Shade No. Shade No. terymarch Park, Quincy, MA 02269
Less Than 300* 8 9 11. CGA Pamphlet P-1, SAFE HANDLING OF COMPRESSED
300 - 400* 9 12 GASES IN CYLINDERS, obtainable from the Compressed
Gas Association, 1235 Jefferson Davis Highway, Suite 501,
400 - 800* 10 14 Arlington, VA 22202
* These values apply where the actual arc is clearly 12. CSA Standard W117.2, CODE FOR SAFETY IN WELDING
seen. Experience has shown that lighter filters may AND CUTTING, obtainable from the Canadian Standards As-
be used when the arc is hidden by the workpiece. sociation, Standards Sales, 178 Rexdale Boulevard, Rexdale,
Ontario, Canada M9W 1R3
13. NWSA booklet, WELDING SAFETY BIBLIOGRAPHY obtainable
from the National Welding Supply Association, 1900 Arch
Street, Philadelphia, PA 19103
14. American Welding Society Standard AWSF4.1, RECOM-
MENDED SAFE PRACTICES FOR THE PREPARATION FOR
1-2 GENERAL INFORMATION Manual 0-4981
CUTMASTER A60
WELDING AND CUTTING OF CONTAINERS AND PIPING THAT devrait consulter leur membre professionel de
HAVE HELD HAZARDOUS SUBSTANCES, obtainable from the médication et le manufacturier de matériel de santé
American Welding Society, 550 N.W. LeJeune Rd, Miami, FL
33126 pour déterminer s’il existe des risques de santé.
15. ANSI Standard Z88.2, PRACTICE FOR RESPIRATORY PROTEC- Il faut communiquer aux opérateurs et au personnel TOUS
TION, obtainable from American National Standards Institute, les dangers possibles. Afin d’éviter les blessures possi-
1430 Broadway, New York, NY 10018 bles, lisez, comprenez et suivez tous les avertissements,
toutes les précautions de sécurité et toutes les consignes
avant d’utiliser le matériel. Composez le + 603-298-5711
1.04 Note, Attention et Avertissement ou votre distributeur local si vous avez des questions.
Dans ce manuel, les mots “note”, “attention”, et “avertissement” sont
utilisés pour mettre en relief des informations à caractère important.
Ces mises en relief sont classifiées comme suit :
FUMÉE et GAZ
NOTE
La fumée et les gaz produits par le procédé de jet de plasma peuvent
Toute opération, procédure ou renseignement présenter des risques et des dangers de santé.
général sur lequel il importe d’insister davantage
• Eloignez toute fumée et gaz de votre zone de respiration. Gardez
ou qui contribue à l’efficacité de fonctionnement votre tête hors de la plume de fumée provenant du chalumeau.
du système.
• Utilisez un appareil respiratoire à alimentation en air si l’aération
fournie ne permet pas d’éliminer la fumée et les gaz.
ATTENTION • Les sortes de gaz et de fumée provenant de l’arc de plasma dépen-

dent du genre de métal utilisé, des revêtements se trouvant sur le
Toute procédure pouvant résulter l’endomma- métal et des différents procédés. Vous devez prendre soin lorsque
gement du matériel en cas de non-respect de la vous coupez ou soudez tout métal pouvant contenir un ou plusieurs
procédure en question. des éléments suivants:
antimoine cadmium mercure
!
argent chrome nickel
arsenic cobalt plomb
AVERTISSEMENT baryum cuivre sélénium
béryllium manganèse vanadium
Toute procédure pouvant provoquer des blessures de
l’opérateur ou des autres personnes se trouvant dans • Lisez toujours les fiches de données sur la sécurité des matières
la zone de travail en cas de non-respect de la procédure (sigle américain “MSDS”); celles-ci devraient être fournies avec
en question. le matériel que vous utilisez. Les MSDS contiennent des rensei-
gnements quant à la quantité et la nature de la fumée et des gaz
pouvant poser des dangers de santé.
• Pour des informations sur la manière de tester la fumée et les gaz
AVERTISSEMENT de votre lieu de travail, consultez l’article 1 et les documents cités
Fournit l'information concernant des dommages pos- à la page 5.
sibles de choc électrique. Des avertissements seront • Utilisez un équipement spécial tel que des tables de coupe à débit
enfermés dans une boîte de ce type. d’eau ou à courant descendant pour capter la fumée et les gaz.
1.05 Precautions De Securite Importantes • N’utilisez pas le chalumeau au jet de plasma dans une zone où se
trouvent des matières ou des gaz combustibles ou explosifs.
!
• Le phosgène, un gaz toxique, est généré par la fumée provenant
des solvants et des produits de nettoyage chlorés. Eliminez toute
AVERTISSEMENTS source de telle fumée.
L’OPÉRATION ET LA MAINTENANCE DU MATÉ- • AVERTISSEMENT: Ce produit contient des produits chimiques,
RIEL DE SOUDAGE À L’ARC AU JET DE PLASMA notamment du plomb, reconnu par l'État de la Californie pour causer
PEUVENT PRÉSENTER DES RISQUES ET DES des malformations congénitales et d'autres dommages touchant
DANGERS DE SANTÉ. le système reproductif. Se laver les mains après manipulation.
Coupant à l’arc au jet de plasma produit de l’énergie

électrique haute tension et des émissions magné-
tique qui peuvent interférer la fonction propre d’un CHOC ELECTRIQUE
“pacemaker” cardiaque, les appareils auditif, ou Les chocs électriques peuvent blesser ou même tuer. Le procédé au jet
autre matériel de santé electronique. Ceux qui trade plasma requiert et produit de l’énergie électrique haute tension. Cette
vail près d’une application à l’arc au jet de plasma énergie électrique peut produire des chocs graves, voire mortels, pour
l’opérateur et les autres personnes sur le lieu de travail.
Manuel 0-4981 INFORMATIONS GÉNÉRALES 1-3
CUTMASTER A60
• Ne touchez jamais une pièce “sous tension” ou “vive”; portez des • Pour protéger vos yeux, portez toujours un casque ou un écran
gants et des vêtements secs. Isolez-vous de la pièce de travail ou de soudeur. Portez toujours des lunettes de sécurité munies de
des autres parties du circuit de soudage. parois latérales ou des lunettes de protection ou une autre sorte
de protection oculaire.
• Réparez ou remplacez toute pièce usée ou endommagée.
• Portez des gants de soudeur et un vêtement protecteur approprié
• Prenez des soins particuliers lorsque la zone de travail est humide pour protéger votre peau contre les étincelles et les rayons de l’arc.
ou moite.
• Maintenez votre casque et vos lunettes de protection en bon état.
• Montez et maintenez le matériel conformément au Code électrique Remplacez toute lentille sale ou comportant fissure ou rognure.
national des Etats-Unis. (Voir la page 5, article 9.)
• Protégez les autres personnes se trouvant sur la zone de travail
• Débranchez l’alimentation électrique avant tout travail d’entretien contre les rayons de l’arc en fournissant des cabines ou des écrans
ou de réparation. de protection.
• Lisez et respectez toutes les consignes du Manuel de consignes. • Utilisez la nuance de lentille qui est suggèrée dans le recommen-
dation qui suivent ANSI/ASC Z49.1:
Nuance Minimum Nuance Suggerée
INCENDIE ET EXPLOSION Courant Arc Protective Numéro Numéro
Les incendies et les explosions peuvent résulter des scories chaudes, Moins de 300* 8 9
des étincelles ou de l’arc de plasma. Le procédé à l’arc de plasma 300 - 400* 9 12
produit du métal, des étincelles, des scories chaudes pouvant mettre
le feu aux matières combustibles ou provoquer l’explosion de fumées 400 - 800* 10 14
inflammables.
* Ces valeurs s’appliquent ou l’arc actuel est
• Soyez certain qu’aucune matière combustible ou inflammable ne observé clairement. L’experience a démontrer que
se trouve sur le lieu de travail. Protégez toute telle matière qu’il les filtres moins foncés peuvent être utilisés quand
est impossible de retirer de la zone de travail. l’arc est caché par moiceau de travail.
• Procurez une bonne aération de toutes les fumées inflammables
ou explosives.
• Ne coupez pas et ne soudez pas les conteneurs ayant pu renfermer BRUIT
des matières combustibles.
Le bruit peut provoquer une perte permanente de l’ouïe. Les procédés
• Prévoyez une veille d’incendie lors de tout travail dans une zone de soudage à l’arc de plasma peuvent provoquer des niveaux sonores
présentant des dangers d’incendie. supérieurs aux limites normalement acceptables. Vous dúez vous
• Le gas hydrogène peut se former ou s’accumuler sous les pièces protéger les oreilles contre les bruits forts afin d’éviter une perte
de travail en aluminium lorsqu’elles sont coupées sous l’eau ou permanente de l’ouïe.
sur une table d’eau. NE PAS couper les alliages en aluminium sous • Pour protéger votre ouïe contre les bruits forts, portez des tampons
l’eau ou sur une table d’eau à moins que le gas hydrogène peut protecteurs et/ou des protections auriculaires. Protégez également
s’échapper ou se dissiper. Le gas hydrogène accumulé explosera les autres personnes se trouvant sur le lieu de travail.
si enflammé.
• Il faut mesurer les niveaux sonores afin d’assurer que les décibels
(le bruit) ne dépassent pas les niveaux sûrs.
• Pour des renseignements sur la manière de tester le bruit, consultez
RAYONS D’ARC DE PLASMA l’article 1, page 5.
Les rayons provenant de l’arc de plasma peuvent blesser vos yeux et
brûler votre peau. Le procédé à l’arc de plasma produit une lumière
infra-rouge et des rayons ultra-violets très forts. Ces rayons d’arc
nuiront à vos yeux et brûleront votre peau si vous ne vous protégez
! AVERTISSEMENT
pas correctement.
AVERTISSEMENT : Ce produit contient des produits chimiques, notam-
ment du plomb, reconnu par l'État de la Californie pour causer des
malformations congénitales et d'autres dommages touchant le système
reproductif. Se laver les mains après manipulation.
1.06 Documents De Reference

Consultez les normes suivantes ou les révisions les plus récentes ayant
été faites à celles-ci pour de plus amples renseignements :
1-4 INFORMATIONS GÉNÉRALES Manuel 0-4981

CUTMASTER A60
1. OSHA, NORMES DE SÉCURITÉ DU TRAVAIL ET DE PROTECTION 9. Norme 70 de la NFPA, CODE ELECTRIQUE NATIONAL, disponible
DE LA SANTÉ, 29CFR 1910, disponible auprès du Superintendent auprès de la National Fire Protection Association, Batterymarch
of Documents, U.S. Government Printing Office, Washington, D.C. Park, Quincy, MA 02269
20402
10. Norme 51B de la NFPA, LES PROCÉDÉS DE COUPE ET DE SOU-
2. Norme ANSI Z49.1, LA SÉCURITÉ DES OPÉRATIONS DE COUPE DAGE, disponible auprès de la National Fire Protection Association,
ET DE SOUDAGE, disponible auprès de la Société Américaine de Batterymarch Park, Quincy, MA 02269
Soudage (American Welding Society), 550 N.W. LeJeune Rd.,
Miami, FL 33126 11. Brochure GCA P-1, LA MANIPULATION SANS RISQUE DES GAZ
COMPRIMÉS EN CYLINDRES, disponible auprès de l’Association
3. NIOSH, LA SÉCURITÉ ET LA SANTÉ LORS DES OPÉRATIONS DE des Gaz Comprimés (Compressed Gas Association), 1235 Jefferson
COUPE ET DE SOUDAGE À L’ARC ET AU GAZ, disponible auprès Davis Highway, Suite 501, Arlington, VA 22202
du Superintendent of Documents, U.S. Government Printing Office,
Washington, D.C. 20402 12. Norme CSA W117.2, CODE DE SÉCURITÉ POUR LE SOUDAGE
ET LA COUPE, disponible auprès de l’Association des Normes
4. Norme ANSI Z87.1, PRATIQUES SURES POUR LA PROTECTION Canadiennes, Standards Sales, 178 Rexdale Boulevard, Rexdale,
DES YEUX ET DU VISAGE AU TRAVAIL ET DANS LES ECOLES, Ontario, Canada, M9W 1R3
disponible de l’Institut Américain des Normes Nationales (American
National Standards Institute), 1430 Broadway, New York, NY 10018 13. Livret NWSA, BIBLIOGRAPHIE SUR LA SÉCURITÉ DU SOUDAGE,
disponible auprès de l’Association Nationale de Fournitures de
5. Norme ANSI Z41.1, NORMES POUR LES CHAUSSURES PRO- Soudage (National Welding Supply Association), 1900 Arch Street,
TECTRICES, disponible auprès de l’American National Standards Philadelphia, PA 19103
Institute, 1430 Broadway, New York, NY 10018
14. Norme AWSF4.1 de l’Association Américaine de Soudage, RECOM-
6. Norme ANSI Z49.2, PRÉVENTION DES INCENDIES LORS DE MANDATIONS DE PRATIQUES SURES POUR LA PRÉPARATION À
L’EMPLOI DE PROCÉDÉS DE COUPE ET DE SOUDAGE, disponible LA COUPE ET AU SOUDAGE DE CONTENEURS ET TUYAUX AYANT
auprès de l’American National Standards Institute, 1430 Broadway, RENFERMÉ DES PRODUITS DANGEREUX , disponible auprès de
New York, NY 10018 la American Welding Society, 550 N.W. LeJeune Rd., Miami, FL
33126
7. Norme A6.0 de l’Association Américaine du Soudage (AWS), LE
SOUDAGE ET LA COUPE DE CONTENEURS AYANT RENFERMÉ 15. Norme ANSI Z88.2, PRATIQUES DE PROTECTION RESPIRATOIRE,
DES PRODUITS COMBUSTIBLES, disponible auprès de la American disponible auprès de l’American National Standards Institute, 1430
Welding Society, 550 N.W. LeJeune Rd., Miami, FL 33126 Broadway, New York, NY 10018
8. Norme 51 de l’Association Américaine pour la Protection contre les
Incendies (NFPA), LES SYSTEMES À GAZ AVEC ALIMENTATION
EN OXYGENE POUR LE SOUDAGE, LA COUPE ET LES PROCÉDÉS
ASSOCIÉS, disponible auprès de la National Fire Protection Asso-
ciation, Batterymarch Park, Quincy, MA 02269
Manuel 0-4981 INFORMATIONS GÉNÉRALES 1-5

CUTMASTER A60
1.07 Declaration of Conformity
Declaration of Conformity
Application of Council Directive(s): The equipment described in this document conforms to all applicable aspects and regula-
tions of the ‘Low Voltage Directive’ (European Council Directive 2006/95/EC) and to the National legislation for the enforcement
of this Directive.
The equipment described in this document conforms to all applicable aspects and regulations of the “EMC Directive” (European
Council Directive 2004/108/EC) and to the National legislation for the enforcement of this Directive.
Manufacturer: Victor Technologies International Inc.

Address: 16052 Swingley Ridge Road
Suite 300
Chesterfield, MO 63033 U.S.A.
Type of Equipment: Plasma Cutting Power Source
Model /Number: CutMaster A60
Serial Number: Serial numbers are unique with each individual piece of equipment and details description, parts used
to manufacture a unit and date of manufacture.
Market Release Date: January 1, 2012
Classification: The equipment described in this document is Class A and intended for industrial use.
! WARNING
This Class A equipment is not intended for use in residential locations where the electrical power is provided by the public low-
voltage supply system. There may be potential difficulties in ensuring electromagnetic compatibility in those locations, due to
conducted as well as radiated disturbances.
The product is designed and manufactured to a number of standards and technical requirements. Among them are:
Harmonized Standard of “EMC Directive”
EN 60974-10:2007 Arc Welding Equipment - Part 10: Electromagnetic compatibility (EMC) requirements
Harmonized Standard of “Low Voltage Directive”
EN 60974-1:2012 Arc Welding Equipment - Part 1: Welding power sources. (Supersedes Standard EN 60974-1:2005)
Extensive product design verification is conducted at the manufacturing facility as part of the routine design and manufacturing process. This
is to ensure the product is safe, when used according to instructions in the manual and related industry standards, and performs as specified.
Rigorous testing is incorporated into the manufacturing process to ensure the manufactured product meets or exceeds all design specifications.
Victor Technologies. has been manufacturing products for more than 30 years, and will continue to achieve excellence in our area of manufacture.
Manufacturer’s Authorized Representative
Steve Ward V.P. Europe and General Manager
Address: Victor Technologies International Inc.
Europa Building (Signature)
Chorley N Industrial Park
Chorley, Lancashire, Steve Ward
England PR6 7BX Full Name
Date: March 18, 2014 V.P. Europe and General Manager

(Position)

CUTMASTER A60
Classification: The equipment described in this manual is Class A and intended for industrial use.
! WARNING
This Class A equipment is not intended for use in residential locations where the electrical power is provided by the
public low-voltage supply system. There may be potential difficulties in ensuring electromagnetic compatibility in
those locations, due to conducted as well as radiated disturbances.
Manual 0-4981 GENERAL INFORMATION 1-7

CUTMASTER A60
1.08 Statement of Warranty
LIMITED WARRANTY: Subject to the terms and conditions established below, Victor Thermal Dynamics® Corporation warrants
to the original retail purchaser that new Victor Thermal Dynamics CUTMASTER™ plasma cutting systems sold after the effective
date of this warranty are free of defects in material and workmanship. Should any failure to conform to this warranty appear
within the applicable period stated below, Victor Technologies, Inc. shall, upon notification thereof and substantiation that the
product has been stored operated and maintained in accordance with Victor Thermal Dynamics’ specifications, instructions,
recommendations and recognized industry practice, correct such defects by suitable repair or replacement.
This warranty is exclusive and in lieu of any warranty of merchantability or fitness for a particular purpose.
Victor Thermal Dynamics will repair or replace, at its discretion, any warranted parts or components that fail due to defects in
material or workmanship within the time periods set out below. Victor Technologies, Inc. must be notified within 30 days of any
failure, at which time Victor Technologies, Inc. will provide instructions on the warranty procedures to be implemented.
Victor Technologies, Inc. will honor warranty claims submitted within the warranty periods listed below. All warranty periods begin
on the date of sale of the product to the original retail customer or 1 year after sale to an authorized Victor Thermal Dynamics
Distributor.
LIMITED WARRANTY PERIOD
Power Supply Components Torch and Leads

Product
(Parts and Labor) (Parts and Labor)
U.S. Non U.S.
CUTMASTER® A40 4 Years 3 Years 1 Year
This warranty does not apply to:
1. Consumable Parts, such as tips, electrodes, shield cups, o-rings, starter cartridges, gas distributors, fuses, filters.
2. Equipment that has been modified by an unauthorized party, improperly installed, improperly operated or misused based upon
industry standards.
In the event of a claim under this warranty, the remedies shall be, at the discretion of Victor Technologies, Inc.:
1. Repair of the defective product.
2. Replacement of the defective product.
3. Reimbursement of reasonable costs of repair when authorized in advance by Victor Thermal Dynamics.
4. Payment of credit up to the purchase price less reasonable depreciation based on actual use.
These remedies may be authorized by Victor Thermal Dynamics and are FOB West Lebanon, NH or an authorized Victor Technologies
service station. Product returned for service is at the owner’s expense and no reimbursement of travel or transportation is authorized.
LIMITATION OF LIABILITY: Victor Technologies, Inc. shall not under any circumstances be liable for special or consequential
damages such as, but not limited to, damage or loss of purchased or replacement goods or claims of customer of distributors
(hereinafter “Purchaser”) for service interruption. The remedies of the Purchaser set forth herein are exclusive and the liability
of Victor Thermal Dynamics with respect to any contract, or anything done in connection therewith such as the performance or
breach thereof, or from the manufacture, sale, delivery, resale, or use of the goods covered by or furnished by Victor Thermal
Dynamics whether arising out of contract, negligence, strict tort, or under any warranty, or otherwise, shall not, except as expressly
provided herein, exceed the price of the goods upon which liability is based.
This warranty becomes invalid if replacement parts or accessories are used which may impair the safety or performance of
any Victor Thermal Dynamics product.
This warranty is invalid if the Victor Thermal Dynamics product is sold by non - authorized persons.
Effective September 4, 2007

CUTMASTER A60
SECTION 2 SYSTEM: 2.02 Equipment Identification
INTRODUCTION The unit’s identification number (specification or part number),
model, and serial number usually appear on a data tag attached
to the rear panel. Equipment which does not have a data tag
2.01 How To Use This Manual such as torch and cable assemblies are identified only by the
specification or part number printed on loosely attached card
This Owner’s Manual applies to just specification or part
or the shipping container. Record these numbers on the bottom
numbers listed on page i.
of page i for future reference.
To ensure safe operation, read the entire manual, including the
chapter on safety instructions and warnings. 2.03 Receipt Of Equipment
Throughout this manual, the words WARNING, CAUTION, When you receive the equipment, check it against the invoice
and NOTE may appear. Pay particular attention to the to make sure it is complete and inspect the equipment for pos-
information provided under these headings. These special sible damage due to shipping. If there is any damage, notify the
annotations are easily recognized as follows: carrier immediately to file a claim. Furnish complete information
concerning damage claims or shipping errors to the location in
NOTE your area listed in the inside back cover of this manual.
An operation, procedure, or background informa- Include all equipment identification numbers as described above
tion which requires additional emphasis or is help- along with a full description of the parts in error.
ful in efficient operation of the system.
Move the equipment to the installation site before un-crating
the unit. Use care to avoid damaging the equipment when using
bars, hammers, etc., to un-crate the unit.
CAUTION
cause damage to the equipment.
! WARNING
cause injury to the operator or others in the op-
erating area.
WARNING
Gives information regarding possible electrical
shock injury. Warnings will be enclosed in a box
such as this.
Additional copies of this manual may be purchased by contact-

ing Victor Technologies at the address and phone number in
your area listed in the inside back cover of this manual. Include
the Owner’s Manual number and equipment identification
numbers.
Electronic copies of this manual can also be downloaded at no
charge in Acrobat PDF format by going to the Victor Thermal
Dynamics web site listed below and clicking on Thermal
Dynamics and then on the Literature link:
http://www.victor-thermaldynamics.com
Manual 0-4981 INTRODUCTION 2-1

CUTMASTER A60
2.04 Power Supply Specifications
CutMaster A60 Power Supply Specifications

208 / 230 VAC (187 - 253 VAC), Single Phase, 60 Hz
230 VAC (187 - 253 VAC), Three Phase, 50/60 Hz
380 VAC (360 - 440 VAC), Three Phase, 50/60 Hz
Input Power 400 VAC (360 - 440 VAC), Three Phase, 50/60 Hz
460 VAC (414 - 506 VAC), Single Phase, 60 Hz
460 VAC (414 - 506 VAC), Three Phase, 60 Hz
600 VAC (540 - 630), Three Phase, 60 Hz
Power Supply includes input cable. Cable for 208/230V input
Input Power Cable
power includes molded plug.
Output Current 20 - 80 Amps, Continuously Adjustable
Power Supply Gas
Particulates to 5 Microns
Filtering Ability
CutMaster A60 Power Supply Duty Cycle *
Duty Cycle Ratings @ 40° C (104° F)
Ambient Temperature
Operating Range 0° - 50° C
IEC IEC IEC
Rating Rating Rating
Duty Cycle 40% 60% 100%
All Units Current 80 Amps 65 Amps 50 Amps
DC Voltage 112 106 100
* NOTE: The duty cycle will be reduced if the primary input power (AC) is low or the
output voltage (DC) is higher than shown in this chart.
NOTE
IEC Rating is determined as specified by the International Electro-Technical Commission. These specifications include
calculating an output voltage based upon power supply rated current. To facilitate comparison between power sup-
plies, all manufacturers use this output voltage to determine duty cycle.
Power Supply Dimensions & Weight Ventilation Clearance Requirements

10"
254 mm
Art # A-08305
Art # A-07925_AB
13.78"
350 mm
6"
150 mm
24"
610 mm
20.8"
6" 6"
0.528 m 150 mm
43 lb / 19.5 kg 150 mm
2-2 INTRODUCTION Manual 0-4981

CUTMASTER A60
2.05 Input Wiring Specifications
CutMaster A60 Power Supply Input Cable Wiring Requirements

Input voltage Freq Power Input Suggested Sizes
Flexible Cord
Volts Hz kVA I max I eff Fuse (amps) (Min. AWG)
208 60 16 75 48 100 6
1 Phase 230 60 17 72 46 100 6
460 60 20 44 28 50 10
208 60 16 40 26 50 8
230 50/60 16 39 25 50 10
380 50/60 11.8 17 11 20 12
3 Phase
400 50/60 11.8 17 11 20 12
460 60 17 21 14 25 12
600 60 9.6 16 10 20 12
Line Voltages with Suggested Circuit Protection and Wire Sizes
Based on National Electric Code and Canadian Electric Code
NOTE
Refer to Local and National Codes or local authority having jurisdiction for proper wiring requirements.
Cable size is de-rated based on the Duty Cycle of the equipment.
Manual 0-4981 INTRODUCTION 2-3

CUTMASTER A60
2.06 Power Supply Features
Control Panel
Art # A-08306
Torch Leads
Receptacle
Mounting Rails
Work Cable
and Clamp
Automation Interface
Cable Port
Input Power Selection
Filter Assembly
Gas Inlet Port
Input Power Cord Art # A-08318
2-4 INTRODUCTION Manual 0-4981

CUTMASTER A60
SECTION 2 TORCH: 2. Machine Torch, Model
The standard machine torch has a positioning tube with
INTRODUCTION rack & pinch block assembly.
15.875" / 403 mm
9.285" / 236 mm
2T.01 Scope of Manual
This manual contains descriptions, operating instructions and
maintenance procedures for the 1Torch Models SL60/Manual 1.175" / 30 mm
1.375" / 35 mm
and SL100/Mechanized Plasma Cutting Torches. Service of 4.95" / 126 mm
this equipment is restricted to properly trained personnel; 1.75" / 0.625" /
unqualified personnel are strictly cautioned against attempting 44.5 mm 16 mm Art # A-02998
repairs or adjustments not covered in this manual, at the risk 3. Hand/Manual Torch, Models
of voiding the Warranty.
The hand torch head is at 75° to the torch handle. The
Read this manual thoroughly. A complete understanding of the hand torches include a torch handle and torch trigger
characteristics and capabilities of this equipment will assure the assembly.
dependable operation for which it was designed. 10.125" (257 mm)
2T.02 General Description

Plasma torches are similar in design to the automotive spark
plug. They consist of negative and positive sections separated
by a center insulator. Inside the torch, the pilot arc starts in the 3.75"
(95 mm)
gap between the negatively charged electrode and the positively Art # A-03322_AB
charged tip. Once the pilot arc has ionized the plasma gas, the
1.17" (29 mm)
superheated column of gas flows through the small orifice in
the torch tip, which is focused on the metal to be cut. B. Torch Leads Lengths
A single torch lead provides gas from a single source to be Hand Torches are available as follows:
used as both the plasma and secondary gas. The air flow is
divided inside the torch head. Single - gas operation provides • 20 ft / 6.1 m, with ATC connectors
a smaller sized torch and inexpensive operation. • 50 ft / 15.2 m, with ATC connectors
NOTE Machine / Automation Torches are available as follows:
Refer to Section "2T.05 Introduction to • 5 foot / 1.5 m, with ATC connectors
Plasma" for a more detailed description of plasma • 10 foot / 3.05 m, with ATC connectors
torch operation.
• 25 foot / 7.6 m, with ATC connectors
Refer to the Appendix Pages for additional specifi- • 50 foot / 15.2 m, with ATC connectors
cations as related to the Power Supply used.
C. Torch Parts
2T.03 Specifications Starter Cartridge, Electrode, Tip, Shield Cup
A. Torch Configurations D. Parts - In - Place (PIP)

1. Automation Torch, Model Torch Head has built - in switch
The standard automation torch has a positioning tube
with rack & pinch block assembly and a solenoid valve. 12 VDC circuit rating
18.875" / 479 mm
E. Type Cooling
12.285" / 312 mm
2.875” / Combination of ambient air and gas stream through torch.
73 mm
1.375" / 35 mm
1.75" / 0.625" / 4.95" / 126 mm 1.175" / 30 mm
44.5 mm 16 mm Art # A-07402_AC
Manual 0-4981 INTRODUCTION 2T-1

CUTMASTER A60
F. Torch Ratings 2T.05 Introduction to Plasma
Automated / Machine Torch Ratings
Ambient 104° F A. Plasma Gas Flow
Temperature 40° C Plasma is a gas which has been heated to an extremely
Duty Cycle 100% @ 100 Amps @ 400 scfh high temperature and ionized so that it becomes electri-
Maximum Current 120 Amps cally conductive. The plasma arc cutting and gouging
processes use this plasma to transfer an electrical arc to
Voltage (Vpeak) 500V the workpiece. The metal to be cut or removed is melted
Arc Striking Voltage 7kV by the heat of the arc and then blown away.
While the goal of plasma arc cutting is separation of the
Manual Torch Ratings
material, plasma arc gouging is used to remove metals to
Ambient 104° F a controlled depth and width.
Temperature 40° C
In a Plasma Cutting Torch a cool gas enters Zone B, where
Duty Cycle 100% @ 60 Amps @ 400 scfh
a pilot arc between the electrode and the torch tip heats and
Maximum Current 60 Amps ionizes the gas. The main cutting arc then transfers to the
Voltage (Vpeak) 500V workpiece through the column of plasma gas in Zone C.
Arc Striking Voltage 7kV
G. Gas Requirements
Automated, Manual and Machine Torch Gas

Specifications
Gas (Plasma and Secondary) Compressed Air
Operating Pressure 60 - 95 psi
Refer to NOTE 4.1 - 6.5 bar
Maximum Input Pressure 125 psi / 8.6 bar A

_
Gas Flow (Cutting and 300 - 500 scfh Power
Gouging) 142 - 235 lpm Supply
+
!
B
WARNING
This torch is not to be used with oxygen (O2). Workpiece
C A-08331
NOTE
Typical Torch Head Detail
Operating pressure varies with torch model, operat-
ing amperage, and torch leads length. Refer to gas
By forcing the plasma gas and electric arc through a small
pressure settings charts for each model.
orifice, the torch delivers a high concentration of heat to a
small area. The stiff, constricted plasma arc is shown in
H. Direct Contact Hazard
Zone C. Direct current (DC) straight polarity is used for
For standoff tip the recommended standoff is 3/16 inches plasma cutting, as shown in the illustration.
/ 4.7 mm.
Zone A channels a secondary gas that cools the torch. This
gas also assists the high velocity plasma gas in blowing
2T.04 Options And Accessories the molten metal out of the cut allowing for a fast, slag -
free cut.
For options and accessories, see Section 6.
2T-2 INTRODUCTION Manual 0-4981

CUTMASTER A60
B. Gas Distribution Remote Pendant
The single gas used is internally split into plasma and

secondary gases.
The plasma gas flows into the torch through the negative
lead, through the starter cartridge, around the electrode, To ATC PIP Switch Shield Cup
and out through the tip orifice.
The secondary gas flows down around the outside of the
torch starter cartridge, and out between the tip and shield
cup around the plasma arc. CNC Start
C. Pilot Arc
When the torch is started a pilot arc is established between
the electrode and cutting tip. This pilot arc creates a path PIP Switch
To ATC Shield Cup
for the main arc to transfer to the work.
D. Main Cutting Arc
Art # A-08168
DC power is also used for the main cutting arc. The nega-
tive output is connected to the torch electrode through
the torch lead. The positive output is connected to the
workpiece via the work cable and to the torch through a Automation Torch
pilot wire.
E. Parts - In - Place (PIP) To ATC PIP Switch Shield Cup
The torch includes a 'Parts - In - Place' (PIP) circuit. When

the shield cup is properly installed, it closes a switch. The Parts - In - Place Circuit Diagram for Machine Torch
torch will not operate if this switch is open.
Torch Switch Torch Trigger

To Control
Cable Wiring
PIP Switch Shield Cup
A-02997
Parts - In - Place Circuit Diagram for Hand Torch
Manual 0-4981 INTRODUCTION 2T-3

CUTMASTER A60
This Page Intentionally Blank
2T-4 INTRODUCTION Manual 0-4981

CUTMASTER A60
SECTION 3 SYSTEM: 2. Place the unit in the desired position and mark where
INSTALLATION the four keyway holes in the mounting

rails touch.
3.01 Unpacking 3. Remove the unit and using these markings, prepare
holes for mounting hardware.
1. Use the packing lists to identify and account for each
item. 4. Insert proper hardware. If using hardware that screws
into the mounting surface, leave all four loose enough
2. Inspect each item for possible shipping damage. If for the thickness of the rail to slide under the head and
damage is evident, contact your distributor and / or washer if used.
shipping company before proceeding with the instal-
lation. 5. Lower the power supply over the mounting hardware
and slide forward or backward until the keyway stops
3. Record Power Supply and Torch model and serial against the mounting hardware.
numbers, purchase date and vendor name, in the in-
formation block at the front of this manual. 6. Secure the hardware to the rail.
3.02 Lifting Options 3.04 Opening the Contactor Cover

The Power Supply includes hand holds in the front and rear The input power cord is connected to the main contactor, the
panels for hand lifting only. Be sure unit is lifted and trans- contactor is located inside a box with a snap on cover. The cover
ported safely and securely. is held in place with two or more snap lock tabs. To remove
the cover release the front latch and tilt the cover up about ½
inch. Then squeeze both sides of the cover and lift it straight
! WARNING
up. See the Primary Input Power Connections section for the
necessary changes to the Contactor. Remember to replace the
Do not touch live electrical parts. Contactor Cover when the changes are complete.
Disconnect input power cord before moving unit.

FALLING EQUIPMENT can cause serious personal
injury and can damage equipment.
1
2
1
• Only persons of adequate physical strength should lift

2
the unit.
• Lift unit by the handles, using two hands. Do not use
straps for lifting.
• Use optional cart or similar device of adequate capacity
to move unit.
Art# A-11478
• Place unit on a proper skid and secure in place before Contactor cover
transporting with a fork lift or other vehicle.
3.03 Power Supply location and Mounting

3.05 Primary Input Power Connections
NOTE
It is recommended that the unit be secured to a
suitable surface using the mounting rails.
CAUTION
1. First choose an appropriate location for mounting the
Check your power source for correct voltage be-
power supply. Choose one that allows for free move-
fore plugging in or connecting the unit. Check the
ment of torch leads, complies with ventilation per
Voltage Selector at the rear of the unit for correct
Section 2.04 and provides a safe firm surface where
setting before plugging in or connecting the unit.
the unit can be secured.
The primary power source, fuse, and any extension
cords used must conform to local electrical code
and the recommended circuit protection and wiring
requirements as specified in Section 2.
Manual 0-4981 INSTALLATION 3-1
CUTMASTER A60
Most units are shipped from the factory with a 230 Volt input C. Input Power Selection
power cable wired to the input contactor in the single - phase
configuration. The following illustrations and directions are Set the Input Voltage Selection Switch at the rear of the unit
for changing that configuration to a different voltage and or to based on the primary input voltage it is connected to. Low is
three - phase operation or back again if a change had already 208/230 VAC and high is 460 VAC.
been made.
LO
A. Cover Removal
HI
1. Remove the upper and lower screws which secure the S
cover to the main assembly. Do not loosen the lower
screws inside the cut out slots in the bottom of the
Art # A-08316
cover.
NOTE D. Quick Guide to Phase Wiring
The upper screws and lower screws are not the Single-Phase (1ø) and Jumper Settings
same. Do not mix them. The upper screws are
for threading into the plastic of the front and rear
panels. DO NOT use the finer threaded lower L1 L1 Jumper L1 -L4
screws for this. L2 L2 Jumper
Art # A-07984_AB
L3 L2-L3
L3
Upper
L4
L4
Screws GND
Lower Single Phase Input Power Wiring

Screws
Three-Phase (3ø) and Jumper Settings
Slots Store copper jumper in spare parts box
L1 L1 Jumper L1 -L4
Lower
Screws L2 L2
Art # A-07983_AB
L3
L3
L4
L4
GND
Three Phase Input Power Wiring
NOTE
There is only one jumper setting that changes
Art # A-08317
between the single and three phase settings. To
change from single phase to three phase, the cop-
2. Carefully pull the Cover up and away from the unit. per bus bar jumper connected to L2 and L3 needs
to be removed and placed in a safe place for re-
use. We suggest the spare parts box in the power
B. Cover Installation
supply. See previous illustrations.
1. Reverse previous procedures for cover installation.
NOTE
When installing the upper screws, attempt to reuse
the original threads. The easiest way to do this is
by turning the screw counter-clockwise until you
feel the threads line up, then begin to turn the screw
clockwise to tighten. Do not over tighten.
3-2 INSTALLATION Manual 0-4981

CUTMASTER A60
E. Connections to Single Phase Input Power F. Connections to Three Phase Input Power
WARNING WARNING
Disconnect input power from the power supply Disconnect input power from the power supply
and input cable before attempting this procedure. and input cable before attempting this procedure.
These instructions are for changing the input power and or These instructions are for changing the input power and or
cable on the 208/230, 400, 460 VAC Power Supply to Single - cable on the 208/230, 400, 460 VAC Power Supply to Three -
Phase input power. Phase input power.
1. Remove the Power Supply cover. See "A. Cover 1. Remove the Power Supply cover. See "A. Cover
Removal". Removal".
2. Disconnect the original input power cable from the 2. Disconnect the original input power cable from the main
main input contactor and the chassis ground connec- input contactor and the chassis ground connection.
tion.
3. Loosen the through - hole protector on the back panel
3. Loosen the through - hole protector on the back panel of the power supply. Pull the original power cable out
of the power supply. Pull the original power cable out of the power supply.
of the power supply.
4. Using a customer supplied four - conductor input
4. If the power cable being used is not the factory - sup- power cable for the voltage desired, strip back the
plied cable, use a three - conductor input power cable insulation on the individual wires.
for the voltage desired and strip back the insulation on
the individual wires. 5. Pass the cable being used through the access opening
in the back panel of the power supply. Refer to Section
5. Pass the cable being used through the access opening "2.04 Power Supply Specifications" for power cable
in the back panel of the power supply. Refer to Section specifications.
"2.04 Power Supply Specifications" for power cable
specifications.
CAUTION
The primary power source and power cable must
CAUTION conform to local electrical code and the recom-
The primary power source and power cable must mended circuit protection and wiring requirements
conform to local electrical code and the recom- (refer to table in Section 2).
mended circuit protection and wiring requirements
6. Connect the wires as follows.
(refer to table in Section 2).
• Remove the copper bus bar jumper from L2 and
6. Connect the wires as follows. L3 on the contactor. See previous illustration.
• Set Jumper wire and copper bus bar / jumper on • Green / Yellow wire to Ground.
the contactor. See previous illustrations.
• Remaining wires to L1, L2 and L3 input. It does
• Green / Yellow wire to Ground. not matter what order these wires are attached.
• Remaining wires to L1 and L2 input. It does not See the previous illustrations.
matter what order these wires are attached. 7. With a little slack in the wires, tighten the through - hole
7. With a little slack in the wires, tighten the through - hole protector to secure the power cable.
protector to secure the power cable. 8. Reinstall the Power Supply cover. See "B. Cover
8. Reinstall the Power Supply cover. See "B. Cover Installation".
Installation". 9. Connect the opposite end of individual wires to a cus-
9. Connect the opposite end of individual wires to a tomer supplied plug or main disconnect.
customer supplied plug or main disconnect. 10. Connect the input power cable (or close the main
10. Connect the input power cable (or close the main disconnect switch) to supply power.
disconnect switch) to supply power.

CUTMASTER A60
3.06 Gas Connections Filter Assembly
Connecting Gas Supply to Unit

Inlet Port
The connection is the same for compressed air or high pressure
cylinders. Refer to the following subsections if an optional air
line filter is to be installed.
1. Connect the air line to the inlet port. The illustration
shows typical fittings as an example.
NOTE Art # A-08319
For a secure seal, apply thread sealant to the fitting

threads, according to manufacturer's instructions.
Do not use Teflon tape as a thread sealer, as small
Hose Clamp
particles of the tape may break off and block the
small air passages in the torch. 1/4 NPT to 1/4"
Gas Supply
Filter Assembly Hose (6mm) Fitting
Optional Single - Stage Filter Installation

Inlet Port
Using High Pressure Air Cylinders

When using high pressure air cylinders as the air supply:
Hose Clamp
1. Refer to the manufacturer’s specifications for instal-
lation and maintenance procedures for high pressure
Gas Supply regulators.
Hose
2. Examine the cylinder valves to be sure they are clean
and free of oil, grease or any foreign material. Briefly
open each cylinder valve to blow out any dust which
Art # A-08320
may be present.
1/4 NPT or ISO-R
to 1/4” (6mm) Fitting
3. The cylinder must be equipped with an adjustable high
- pressure regulator capable of outlet pressures up to
Air Connection to Inlet Port 100 psi (6.9 bar) maximum and flows of at least 300
scfh (141.5 lpm).
Installing Optional Single - Stage Air Filter
4. Connect supply hose to the cylinder.
An optional filter kit is recommended for improved filtering with
compressed air, to keep moisture and debris out of the torch. NOTE
1. Attach the Single - Stage Filter Hose to the Inlet Port. Pressure should be set at 100 psi (6.9 bar) at the
high pressure cylinder regulator.
2. Attach the Filter Assembly to the filter hose.
Supply hose must be at least 1/4 inch (6 mm) I.D.
3. Connect the air line to the Filter. The illustration shows
typical fittings as an example. For a secure seal, apply thread sealant to the fitting
threads, according to manufacturer's instructions.
NOTE Do Not use Teflon tape as a thread sealer, as small
For a secure seal, apply thread sealant to the fitting particles of the tape may break off and block the
threads, according to the manufacturer's instruc- small air passages in the torch.
tions. Do Not use Teflon tape as a thread sealer,
as small particles of the tape may break off and Installing Optional Two - Stage Air Filter Kit
block the small air passages in the torch. Connect
This optional two - stage air line filter is also for use on
as follows:
compressed air shop systems. Filter removes moisture and
contaminants to at least 5 microns.
Connect the air supply as follows:

CUTMASTER A60
1. Attach the Two Stage Filter bracket to the back of the NOTE
power supply per instructions supplied with the filter
assembly. Pressure should be set at 100 psi (6.9 bar) at the
high pressure cylinder regulator.
NOTE
Supply hose must be at least 1/4 inch (6 mm) I.D.
For a secure seal, apply thread sealant to the fitting
threads according to manufacturer's instructions. For a secure seal, apply thread sealant to the fitting
Do Not use Teflon tape as a thread sealer as small threads, according to manufacturer's instructions.
particles of the tape may break off and block the Do Not use Teflon tape as a thread sealer, as small
small air passages in the torch. particles of the tape may break off and block the
small air passages in the torch.
2. Connect the two stage filter outlet hose to the inlet port
of the Regulator / Filter Assembly.
3. Use customer - supplied fittings to connect the air line
to the Filter. A 1/4 NPT to 1/4" hose barbed fitting is
shown as an example.
Regulator/Filter
Assembly
2-Stage Filter
Regulator Inlet Port (IN)
Input
Outlet Port
(OUT)
Two Stage
Filter
Hose Clamp Assembly
Gas Supply
Hose
1/4 NPT to 1/4”

(6mm) Fitting
Art # A-07945_AC
Optional Two - Stage Filter Installation
Using High Pressure Air Cylinders

When using high pressure air cylinders as the air supply:
1. Refer to the manufacturer’s specifications for instal-
lation and maintenance procedures for high pressure
regulators.
2. Examine the cylinder valves to be sure they are clean
and free of oil, grease or any foreign material. Briefly
open each cylinder valve to blow out any dust which
may be present.
3. The cylinder must be equipped with an adjustable high
- pressure regulator capable of outlet pressures up to
100 psi (6.9 bar) maximum and flows of at least 300
scfh (141.5 lpm).
4. Connect supply hose to the cylinder.

CUTMASTER A60

CUTMASTER A60
SECTION 3 TORCH: Check Air Quality
INSTALLATION To test the quality of air:
1. Put the ON / OFF switch in the ON (up) posi-

3T.01 Torch Connections tion.
If necessary, connect the torch to the Power Supply. Connect 2. Put the Function Control switch in the SET posi-
only the Victor Thermal Dynamics model SL100SV / Automa- tion.
tion, SL100 / Mechanical or SL60 / Manual Torch to this power 3. Place a welding filter lens in front of the torch and turn
supply. Maximum torch leads length is 100 feet / 30.5 m, ON the air. Do not start an arc!
including extensions.
Any oil or moisture in the air will be visible on the lens.
3T.02 CNC Connection

WARNING
Disconnect primary power at the source before 1. Locate the interface connection port on the rear of the
connecting the torch. power supply.
Automation Interface
Cable Port
1. Align the ATC male connector (on the torch lead) with
the female receptacle. Push the male connector into
the female receptacle. The connectors should push
together with a small amount of pressure.
2. Secure the connection by turning the locking nut
clockwise until it clicks. DO NOT use the locking nut
to pull the connection together. Do not use tools to
secure the connection.
Art # A-08322
2. Note the pin-out of the connector and that the customer

supplied connector matches.
Plasma
Start / Stop
Signal
1
Art # A-07885
Connecting the Torch to the Power Supply
3. The system is now ready for operation.
Cutting Machine
Art # A-08323
OK to Move
Manual 0-4981 INSTALLATION 3T-1

CUTMASTER A60
There are three options for Divided Arc Voltage signal supplied from the automation interface pcb. This is selected by
connecting the black Jumper Plug on the P1 connector as follows:
Arc voltage / 16.67 Jumper not installed
Arc voltage / 30 Jumper Pins 1 & 2 . This is the factory default position of the jumper
Arc voltage / 50 Jumper Pins 2 & 3
FULL FEATURED AUTOMATION INTERFACE PCB OPTION
* * To configure DIVIDED ARC VOLTS signal output

No jumper installed for ARC VOLTS /16.67
Jumper pins 1 & 2 for ARC VOLTS / 30
1
2
3
To -V OUT 1 J3
on PCB1
E1 J2
1
2
P10 3
J1 +12VDC
4
} /START / STOP
1 1 5 (-)
2 2 6
} (+) *DIVIDED ARC VOLTS
3 3 K1 7 (-)
4
5
4
5
8
9
} (+) (W/ARC VOLTS
100K IN SERIES (2))
6 6 10
7 7 11
8 8 12
K1 13 } OK-TO-MOVE
14
AUTOMATION
PCB4 INTERFACE PCB
Art # A-09819_AB
WARNING
This divided arc voltage output signal is positive. Its common (-) is referenced to the work lead (ground). Using this
on a height control and expecting a negative signal and whose positive input is grounded may damage the divided
arc voltage circuit.
3. Connect CNC to the power supply.
3T-2 INSTALLATION Manual 0-4981

CUTMASTER A60
3T.03 Setting Up Automation or Machine Torch
NOTE
An adapter is required to be installed in the power
supply if converting a hand torch system to operate
a machine or automation torch.
WARNING
Disconnect primary power at the source before
disassembling the torch or torch leads.
The Automation and Machine torch include a positioning tube

with rack and pinch block assembly.
1. Mount the torch assembly on the cutting table.
2. To obtain a clean vertical cut, use a square to align the
torch perpendicular to the surface of the workpiece.
Pinch Block
Assembly
Square
Workpiece
A-02585
Automated and Machine Torch Set - Up
3. The proper torch parts (shield cup, tip, start cartridge,

and electrode) must be installed for the type of op-
eration. Refer to Section "4T.03 Machine and
Hand Torch Parts Selection" for details.
Manual 0-4981 INSTALLATION 3T-3

CUTMASTER A60
This Page Intentionally blank
3T-4 INSTALLATION Manual 0-4981

CUTMASTER A60
SECTION 4 SYSTEM: 1 2 3 4
OPERATION
4.01 Front Panel Controls / Features
A
MIN MAX
PSI BAR
MAX MAX
+
See Illustration for numbering Identification
1. Output Current Control

MIN MIN
Sets the desired output current. Output settings up to

60 Amps may be used for drag cutting (with the torch tip !
contacting the workpiece) or higher for standoff cutting.
2. Function Control
Function Control Knob, Used to select between the different
operating modes. Art# A-07886
5 6 7 8 9 10
SET Used to purge the air through the unit and
torch and leads and to adjust gas pressure.
6. Temp Indicator
RUN Used for general cutting operations RAPID
Indicator is normally OFF. Indicator is ON when internal
AUTO RESTART Allows for faster restarting of the temperature exceeds normal limits. Let the unit cool before
Pilot Arc for uninterrupted cutting. continuing operation.
LATCH Used for longer hand held cuts. 7. Gas Indicator

Once a cutting arc is established, the torch switch can
be released. The cutting arc will remain ON until the Indicator is ON when minimum input gas pressure for
torch is lifted away from the work piece, the torch leaves power supply operation is present. Minimum pressure for
the edge of the work piece the torch switch is activated power supply operation is not sufficient for torch operation.
again or if one of the system interlocks is activated. 8. DC Indicator
3. ON OFF Power Switch Indicator is ON when DC output circuit is active.
9. ! Fault Error Indicator

ON / OFF Switch controls input power to the power
supply. Up is ON, down is OFF. Indicator is ON when Fault circuit is active. See Section 5
for explanations of fault lights.
4. Air/Gas Pressure Control
10. Pressure Indicators
The Pressure + Control is used in the "SET" PSI BAR

mode to adjust the air/gas pressure. Pull the knob out to MAX MAX
adjust and push in to lock. 90 6.3

85 5.9
5. AC Indicator
80 5.5
Steady light indicates power supply is ready for operation.
75 5.2
Blinking light indicates unit is in protective interlock mode.
Art # A-08170
Shut unit OFF, shut OFF or disconnect input power, correct 70 4.8
the fault, and restart the unit. Refer to Section 5 for details. 65 4.5
MIN MIN
The Indicators will illuminate according to the pressure set

by the Pressure Control Knob (number 4).
Manual 0-4981 OPERATION 4-1

CUTMASTER A60
4.02 Preparations for Operation Power ON
Place the Power Supply ON / OFF switch to the ON (up)
At the start of each operating session:
position. AC indicator turns ON. Gas indicator
turns ON if there is sufficient gas pressure for power supply
WARNING operation and the cooling fans turn ON.
Disconnect primary power at the source before NOTE
assembling or disassembling power supply, torch
parts, or torch and leads assemblies. Minimum pressure for power supply operation is
lower than minimum for torch operation.
The cooling fans will turn ON as soon as the unit
is turned ON. After the unit is idle for ten (10)
Torch Parts Selection minutes the fans will turn OFF. The fans will come
Check the torch for proper assembly and appropriate torch back ON as soon as the torch switch (Start Signal)
parts. The torch parts must correspond with the type of is activated or if the unit is turned OFF, then turned
operation, and with the amperage output of this Power ON again. If an over temperature condition occurs,
Supply (80 amps maximum). Refer to Section "4T.03 the fans will continue to run while the condition
Machine and Hand Torch Parts Selection". exists and for a ten (10) minute period once the
condition is cleared.
Torch Connection
Set Operating Pressure
Check that the torch is properly connected. Only Victor
Thermal Dynamics model SL60 / Manual, SL100 / Mechani- 1. Place the Power Supply Function Control knob to the
cal or SL100 / SV Automation Torches may be connected SET position. Gas will flow.
to this Power Supply. See Section 3T of this manual.
Check Primary Input Power Source 2. For Standoff cutting, adjust gas pressure from 70 - 85
psi / 4.8 - 5.9 bar (LED's in center of control panel).
1. Check the power source for proper input voltage. Make Refer to the Standoff chart on the next page for pres-
sure the input power source meets the power require- sure setting details.
ments for the unit per Section 2, Specifications.
2. Connect the input power cable (or close the main 1 2
disconnect switch) to supply power to the system.
Air Source
Ensure source meets requirements (refer to Section 2).
A
Check connections and turn air supply ON.
MIN MAX
PSI BAR
MAX MAX
Connect Work Cable

Clamp the work cable to the workpiece or cutting table. MIN MIN
The area must be free from oil, paint and rust. Connect
only to the main part of the workpiece; do not connect to !
the part to be cut off.
Art# A-07946
Art # A-04509
4-2 OPERATION Manual 0-4981

CUTMASTER A60
STANDOFF Typical Cutting Speeds
CutMaster A60 Gas Pressure Settings Cutting speeds vary according to torch output amperage,
SL100 the type of material being cut, and operator skill. Refer to
Leads SL60 (Mechanized Torch) Sections "4T.08 Recommended Cutting Speeds for
Length (Hand Torch) SL 100 SV Machine and Automated Torches With Exposed Tip" and
(Automation Torch) following for greater details.
Up to 25' 75 psi 75 psi Output current setting or cutting speeds may be reduced
(7.6 m) 5.2 bar 5.2 bar to allow slower cutting when following a line, or using
a template or cutting guide while still producing cuts of
Each additional 25' Add 5 psi Add 5 psi
excellent quality.
(7.6 m) 0.4 bar 0.4 bar
Postflow
3. For Drag cutting, adjust gas pressure from 75 - 95 psi Release the trigger to stop the cutting arc. Gas continues
/ 5.2 - 6.5 bar (LED's in center of control panel). Refer to flow for approximately 20 seconds. During post - flow, if
to the Drag Cutting chart for pressure setting details. the user moves the trigger release to the rear and presses
the trigger, the pilot arc starts. The main arc transfers to
DRAG the workpiece if the torch tip is within transfer distance to
CutMaster A60 Gas Pressure Settings the workpiece.
Leads SL60 Shutdown
Length (Hand Torch)
Up to 25' 80 psi Turn the ON / OFF switch to OFF (down). All
(7.6 m) 5.5 bar Power Supply indicators shut OFF. Unplug the input power
Each additional Add 5 psi cord or disconnect input power. Power is removed from
25' (7.6 m) 0.4 bar the system.
Select Current Output Level

1. P l a c e t h e F u n c t i o n C o n t r o l K n o b i n o n e
of the three operating positions available:
R U N ,
RAPID AUTO R E S TA R T
or LATCH . Gas flow stops.

2. Set the output current to desired amperage with the
Output Current Control Knob.
Cutting Operation
When the torch leaves the workpiece during cutting opera-
tions with the Function Control Knob in the RUN position,
there is a brief delay in restarting the pilot arc. With the
knob in the RAPID AUTO RESTART position, when
the torch leaves the workpiece the pilot arc restarts in-
stantly, and the cutting arc restarts instantly when the pilot
arc contacts the workpiece. (Use the 'Rapid Auto Restart'
position when cutting expanded metal or gratings, or in
gouging or trimming operations when an uninterrupted
restart is desired). And with the knob in the LATCH posi-
tion the main cutting arc will be maintained after the torch
switch is released.
Manual 0-4981 OPERATION 4-3

CUTMASTER A60
4-4 OPERATION Manual 0-4981

CUTMASTER A60
SECTION 4 TORCH: For optimum smooth surface quality, the travel speed
should be adjusted so that only the leading edge of the arc
OPERATION column produces the cut. If the travel speed is too slow,
a rough cut will be produced as the arc moves from side
to side in search of metal for transfer.
4T.01 Machine and Automated Torch Operation
Travel speed also affects the bevel angle of a cut. When
cutting in a circle or around a corner, slowing down the
Cutting With Machine or Automated Torch travel speed will result in a squarer cut. The power source
These torches are activated by remote control pendant or output should be reduced also. Refer to the appropriate
by a remote interface device such as CNC. Control Module Operating Manual for any Corner Slow-
down adjustments that may be required.
1. To start a cut at the plate edge, position the center of
the torch along the edge of the plate. Piercing With Machine or Automated Torch
To pierce, the arc should be started with the torch posi-
Travel Speed tioned as high as possible above the plate while allowing the
Proper travel speed is indicated by the trail of the arc which arc to transfer and pierce. This standoff helps avoid having
is seen below the plate. The arc can be one of the following: molten metal blow back onto the front end of the torch.
1. Straight Arc When operating with a cutting machine, a pierce or dwell

time is required. Torch travel should not be enabled until
A straight arc is perpendicular to the workpiece surface. the arc penetrates the bottom of the plate. As motion be-
This arc is generally recommended for the best cut us- gins, torch standoff should be reduced to the recommended
ing air plasma on stainless or aluminum. 1/8 - 1/4 inch (3-6 mm) distance for optimum speed and
cut quality. Clean spatter and scale from the shield cup
2. Leading Arc
and the tip as soon as possible. Spraying or dipping the
The leading arc is directed in the same direction as shield cup in anti - spatter compound will minimize the
torch travel. A five degree leading arc is generally amount of scale which adheres to it.
recommended for air plasma on mild steel.
4T.02 Automation Torch Parts Selection
3. Trailing Arc
Check the torch for proper consumable parts. The parts
The trailing arc is directed in the opposite direction as supplied in the torch may not be correct for the operator’s
torch travel. chosen amperage level. The torch parts must correspond
with the type of operation.
Torch parts:
Shield Cup, Cutting Tip, Electrode and Starter Cartridge
Dir NOTE
ect
ion Refer to Sections "4T.02 Automation Torch
of T
orc
hT Parts Selection" and following for additional infor-
rav Standoff Distance
el mation on torch parts.
Change the torch parts for a different operation as follows:
WARNING
Straight Arc
Disconnect primary power at the source before
assembling or disassembling torch parts, or torch
Trailing Arc and leads assemblies.
A-02586
NOTE
Leading Arc
The shield cup holds the tip and starter cartridge in
Automation and Machine Torch Operation place. Position the torch with the shield cup facing
upward to keep these parts from falling out when
the cup is removed.
Manual 0-4981 OPERATION 4T-1

CUTMASTER A60
1. If attached, remove the ohmic clip then unscrew and Change the torch parts for a different operation as follows:
remove the shield cup assembly from the torch head.
Wipe it clean or replace if damaged
WARNING
2. Remove the Electrode by pulling it straight out of the
Torch Head. Disconnect primary power at the source before
Torch Head assembling or disassembling torch parts, or torch
Art # A-04173_AB
and leads assemblies.
Electrode
NOTE
Start Cartridge The shield cup holds the tip and starter cartridge in
place. Position the torch with the shield cup facing
Tip upward to keep these parts from falling out when
the cup is removed.
Ohmic Clip
(If installed) 1. Unscrew and remove the shield cup assembly from
the torch head.
2. Remove the Electrode by pulling it straight out of the
Shield Cup Body Torch Head.
Torch Head
Deflector
Shield Cap
Electrode
Automation Torch Parts

3. Install the replacement Electrode by pushing it straight
Start Cartridge
into the torch head until it clicks.
4. Install the starter cartridge and desired tip for the
operation into the torch head. Tip
5. Hand tighten the shield cup assembly until it is seated

on the torch head. If resistance is felt when installing Shield Cup
the cup, check the threads before proceeding
A-03510_AB
6. If used, attach the ohmic clip to the shield cup.
Torch Parts (Drag Shield Cap & Shield Cup Body Shown)
4T.03 Machine and Hand Torch Parts Selection 3. Install the replacement Electrode by pushing it straight
Depending on the type of operation to be done determines the into the torch head until it clicks.
torch parts to be used. 4. Install the starter cartridge and desired tip for the
Type of operation: operation into the torch head.
Drag cutting, standoff cutting or gouging 5. Hand tighten the shield cup assembly until it is seated
on the torch head. If resistance is felt when installing
Torch parts: the cup, check the threads before proceeding.
Shield Cup, Cutting Tip, Electrode and Starter Cartridge
4T.04 Cut Quality
NOTE
Refer to Section "4T.03 Machine and Hand NOTE
Torch Parts Selection" and following for additional
Cut quality depends heavily on setup and param-
information on torch parts.
eters such as torch standoff, alignment with the
workpiece, cutting speed, gas pressures, and
operator ability.
4T-2 OPERATION Manual 0-4981

CUTMASTER A60
Cut quality requirements differ depending on application. For
4T.05 General Cutting Information
instance, nitride build - up and bevel angle may be major fac-
tors when the surface will be welded after cutting. Dross - free
cutting is important when finish cut quality is desired to avoid
a secondary cleaning operation. The following cut quality ! WARNING
characteristics are illustrated in the following figure:
Disconnect primary power at the source before dis-
Kerf Width assembling the power supply, torch, or torch leads.
Cut Surface
Bevel Angle Frequently review the Important Safety Precautions
Top
at the front of this manual. Be sure the operator
Spatter is equipped with proper gloves, clothing, eye and
ear protection. Make sure no part of the operator’s
body comes into contact with the workpiece while
Top Edge the torch is activated.
Rounding
Dross
Build-Up
Cut Surface A-00007 CAUTION
Drag Lines
Sparks from the cutting process can cause dam-
age to coated, painted, and other surfaces such as
Cut Quality Characteristics
glass, plastic and metal.
Cut Surface NOTE
The desired or specified condition (smooth or rough) of Handle torch leads with care and protect them
the face of the cut. from damage.
Nitride Build - Up Piloting

Nitride deposits can be left on the surface of the cut when Piloting is harder on parts life than actual cutting because
nitrogen is present in the plasma gas stream. These build- the pilot arc is directed from the electrode to the tip rather
ups may create difficulties if the material is to be welded than to a workpiece. Whenever possible, avoid excessive
after the cutting process. pilot arc time to improve parts life.
Bevel Angle Torch Standoff

The angle between the surface of the cut edge and a plane Improper standoff (the distance between the torch tip and
perpendicular to the surface of the plate. A perfectly per- workpiece) can adversely affect tip life as well as shield cup
pendicular cut would result in a 0° bevel angle. life. Standoff may also significantly affect the bevel angle.
Reducing standoff will generally result in a more square cut.
Top - Edge Rounding
Rounding on the top edge of a cut due to wearing from the Edge Starting
initial contact of the plasma arc on the workpiece. For edge starts, hold the torch perpendicular to the work-
piece with the front of the tip near (not touching) the edge
Bottom Dross Buildup of the workpiece at the point where the cut is to start.
Molten material which is not blown out of the cut area When starting at the edge of the plate, do not pause at the
and resolidifies on the plate. Excessive dross may require edge and force the arc to "reach" for the edge of the metal.
secondary cleanup operations after cutting. Establish the cutting arc as quickly as possible.
Kerf Width Direction of Cut

The width of the cut (or the width of material removed In the torches, the plasma gas stream swirls as it leaves
during the cut). the torch to maintain a smooth column of gas. This swirl
effect results in one side of a cut being more square than
Top Spatter (Dross) the other. Viewed along the direction of travel, the right
side of the cut is more square than the left.
Top spatter or dross on the top of the cut caused by slow
travel speed, excess cutting height, or cutting tip whose
orifice has become elongated.

CUTMASTER A60
Left Side 2. Depending on the cutting operation, do one of the fol-
Cut Angle lowing:
Right Side
Cut Angle
a. For edge starts, hold the torch perpendicular to the
workpiece with the front of the tip on the edge of
the workpiece at the point where the cut is to start.
b. For standoff cutting, hold the torch 1/8 - 3/8 in
(3-9 mm) from the workpiece as shown below.
A-00512
Torch
Side Characteristics Of Cut
To make a square - edged cut along an inside diameter of a

circle, the torch should move counterclockwise around the
circle. To keep the square edge along an outside diameter
cut, the torch should travel in a clockwise direction.
Dross
When dross is present on carbon steel, it is commonly
referred to as either “high speed, slow speed, or top dross”. Shield Cup Standoff Distance
Dross present on top of the plate is normally caused by 1/8" - 3/8" (3 - 9mm)
too great a torch to plate distance. "Top dross" is normally
very easy to remove and can often be wiped off with a
welding glove. "Slow speed dross" is normally present on
the bottom edge of the plate. It can vary from a light to
heavy bead, but does not adhere tightly to the cut edge, A-00024_AB
Standoff Distance
and can be easily scraped off. "High speed dross" usually
forms a narrow bead along the bottom of the cut edge and
is very difficult to remove. When cutting a troublesome 3. Hold the torch away from your body.
steel, it is sometimes useful to reduce the cutting speed 4. Slide the trigger release toward the back of the torch
to produce "slow speed dross". Any resultant cleanup can handle while simultaneously squeezing the trigger. The
be accomplished by scraping, not grinding. pilot arc will start.
4T.06 Hand Torch Operation
Standoff Cutting With Hand Torch

NOTE
Trigger
For best performance and parts life, always use the
correct parts for the type of operation.
Trigger Release
1. The torch can be comfortably held in one hand or
steadied with two hands. Position the hand to press A-02986
the Trigger on the torch handle. With the hand torch,

the hand may be positioned close to the torch head for 5. Bring the torch within transfer distance to the work.
maximum control or near the back end for maximum The main arc will transfer to the work, and the pilot arc
heat protection. Choose the holding technique that will shut OFF.
feels most comfortable and allows good control and NOTE
movement.
The gas preflow and postflow are a characteristic
NOTE of the power supply and not a function of the torch.
The tip should never come in contact with the
workpiece except during drag cutting operations.

CUTMASTER A60
Trigger Shield Cup With Straight Edge
The drag shield cup can be used with a non conductive
straight edge to make straight cuts by hand.
1
2
Trigger Release WARNING

The straight edge must be non - conductive.
4 Non-Conductive
Straight Edge
Art # A-03383 Cutting Guide
6. Cut as usual. Simply release the trigger assembly to

stop cutting. A-03539
7. Follow normal recommended cutting practices as Using Drag Shield Cup With Straight Edge
provided in the power supply operator's manual.
NOTE The crown shield cup functions best when cutting 3/16
inch (4.7 mm) solid metal with relatively smooth surface.
When the shield cup is properly installed, there
is a slight gap between the shield cup and the
Drag Cutting With a Hand Torch
torch handle. Gas vents through this gap as part
of normal operation. Do not attempt to force the Drag cutting works best on metal 1/4" (6 mm) thick or less.
shield cup to close this gap. Forcing the shield cup
NOTE
against the torch head or torch handle can damage
components. For best parts performance and life, always use the
correct parts for the type of operation.
8. For a consistent standoff height from the workpiece,
install the standoff guide by sliding it onto the torch 1. Install the drag cutting tip and set the output current.
shield cup. Install the guide with the legs at the sides 2. The torch can be comfortably held in one hand or
of the shield cup body to maintain good visibility of the steadied with two hands. Position the hand to press
cutting arc. During operation, position the legs of the the Trigger on the torch handle. With the hand torch,
standoff guide against the workpiece. the hand may be positioned close to the torch head for
maximum control or near the back end for maximum
heat protection. Choose the holding technique that
feels most comfortable and allows good control and
movement.
4. Keep the torch in contact with the workpiece during
the cutting cycle.
Shield Cup
Standoff Guide 5. Hold the torch away from your body.
Torch Tip 6. Slide the trigger release toward the back of the torch
Workpiece Art # A-04034
handle while simultaneously squeezing the trigger. The
pilot arc will start.

CUTMASTER A60
Piercing With Hand Torch
1. The torch can be comfortably held in one hand or
steadied with two hands. Position the hand to press
the Trigger on the torch handle. With the hand torch,
the hand may be positioned close to the torch head for
Trigger
maximum control or near the back end for maximum
heat protection. Choose the technique that feels most
Trigger Release comfortable and allows good control and movement.
A-02986 NOTE
7. Bring the torch within transfer distance to the work. The tip should never come in contact with the
The main arc will transfer to the work, and the pilot arc workpiece except during drag cutting operations.
will shut OFF.
2. Angle the torch slightly to direct blowback particles
NOTE away from the torch tip (and operator) rather than
directly back into it until the pierce is complete.
of the power supply and not a function of the torch. 3. In a portion of the unwanted metal start the pierce off
the cutting line and then continue the cut onto the line.
Trigger Hold the torch perpendicular to the workpiece after the
pierce is complete.
4. Hold the torch away from your body.
1
2 5. Slide the trigger release toward the back of the torch
handle while simultaneously squeezing the trigger. The
Trigger Release pilot arc will start.
3
Trigger
4
Trigger Release
A-02986
Art # A-03383
6. Bring the torch within transfer distance to the work.

8. Cut as usual. Simply release the trigger assembly to The main arc will transfer to the work, and the pilot arc
stop cutting. will shut OFF.
9. Follow normal recommended cutting practices as NOTE
provided in the power supply operator's manual.
NOTE of the power supply and not a function of the torch.
When the shield cup is properly installed, there
is a slight gap between the shield cup and the When the shield cup is properly installed, there
torch handle. Gas vents through this gap as part is a slight gap between the shield cup and the
of normal operation. Do not attempt to force the torch handle. Gas vents through this gap as part
shield cup to close this gap. Forcing the shield cup of normal operation. Do not attempt to force the
against the torch head or torch handle can damage shield cup to close this gap. Forcing the shield cup
components. against the torch head or torch handle can damage
components.

CUTMASTER A60
7. Clean spatter and scale from the shield cup and the tip
as soon as possible. Spraying the shield cup in anti -
spatter compound will minimize the amount of scale CAUTION
which adheres to it. Touching the torch tip or shield cup to the work
Cutting speed depends on material, thickness, and the opera- surface will cause excessive parts wear.
tor’s ability to accurately follow the desired cut line. The fol-
lowing factors may have an impact on system performance: Torch Travel Speed
• Torch parts wear NOTE

• Air quality Refer to Appendix Pages for additional information
as related to the Power Supply used.
• Line voltage fluctuations
• Torch standoff height Optimum torch travel speed is dependent on current set-
ting, lead angle, and mode of operation (hand or machine
• Proper work cable connection
torch).
Current Setting
4T.07 Gouging
Current settings depend on torch travel speed, mode of
operation (hand or machine torch), and the amount of
! WARNING
material to be removed.
Lead Angle
Be sure the operator is equipped with proper
gloves, clothing, eye and ear protection and that all The angle between the torch and workpiece depends on
safety precautions at the front of this manual have the output current setting and torch travel speed. The
been followed. Make sure no part of the operator’s recommended lead angle is 35°. At a lead angle greater
body comes in contact with the workpiece when than 45° the molten metal will not be blown out of the
the torch is activated. gouge and may be blown back onto the torch. If the lead
angle is too small (less than 35°), less material may be
Disconnect primary power to the system before removed, requiring more passes. In some applications,
disassembling the torch, leads, or power supply. such as removing welds or working with light metal, this
may be desirable.
CAUTION
Sparks from plasma gouging can cause damage
to coated, painted or other surfaces such as glass,
plastic, and metal.
Check torch parts. The torch parts must corre-
spond with the type of operation. Refer to Section
"4T.03 Machine and Hand Torch Parts Selec-
tion".
Gouging Parameters
Gouging performance depends on parameters such as
torch travel speed, current level, lead angle (the angle be-
tween the torch and workpiece), and the distance between
the torch tip and workpiece (standoff).

CUTMASTER A60
Torch Head
35°
Standoff Height
Workpiece
A-00941_AB
Gouging Angle and Standoff Distance
Standoff Distance
The tip to work distance affects gouge quality and depth.
Standoff distance of 1/8 - 1/4 inch (3 - 6 mm) allows for
smooth, consistent metal removal. Smaller standoff dis-
tances may result in a severance cut rather than a gouge.
Standoff distances greater than 1/4 inch (6 mm) may result
in minimal metal removal or loss of transferred main arc.
Slag Buildup
Slag generated by gouging on materials such as carbon and
stainless steels, nickels, and alloyed steels, can be removed
easily in most cases. Slag does not obstruct the gouging
process if it accumulates to the side of the gouge path.
However, slag build - up can cause inconsistencies and
irregular metal removal if large amounts of material build
up in front of the arc. The build - up is most often a result
of improper travel speed, lead angle, or standoff height.

CUTMASTER A60

CUTMASTER A60
4T.08 Recommended Cutting Speeds for Machine and Automated Torches With Exposed Tip
Mild Steel
40A
Air Plasma / Air Shield
Starter Cartridge
Standard Shield Cup
Deflector Tip Heavy Duty Starter Electrode
Maximum Life Shield Cup
Cartridge
9-8218 9-8213
9-8243 9-8208 9-8232
9-8237 9-8277
Torch Initial Kerf Width

Material Gas Pressure
Arc Voltage Working Travel Speed Piercing Pierce Delay @ Rec.
Thickness (Air)
Height Height Speed
PSI
(GA) (in) inch (torch lead Volts (in) (ipm) (in) (sec) (in)
length)
20 0.036 101 0.14 160 0.18 0.0 0.05
16 0.060 103 0.14 140 0.18 0.0 0.05
14 0.075 105 0.14 120 0.18 0.1 0.06
12 0.105 108 0.14 80 0.18 0.2 0.06
70 (25')
10 0.135 110 0.14 60 0.18 0.3 0.06
75 (50')
3/16 0.188 111 0.14 55 0.18 0.4 0.06
1/4 0.250 117 0.14 40 0.18 0.5 0.07
3/8 0.375 119 0.14 25 0.18 1.2 0.07
1/2 0.500 120 0.14 15 0.2 2.0 0.07

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
(mm) (torch lead Volts (mm) (mm/min) (mm) (sec) (mm)
length)
1 101 3.6 3990 4.6 0.0 1.1
2 105 3.6 2920 4.6 0.1 1.4
3 109 3.6 1810 4.6 0.3 1.5
4 110 3.6 1470 4.6 0.3 1.6
4.8 (7.6m)
5 112 3.6 1345 4.6 0.4 1.6
6 5.2 (15.2m) 116 3.6 1100 4.6 0.5 1.7
8 118 3.6 815 4.6 1.0 1.7
10 119 3.6 595 4.6 1.5 1.8
12 120 3.6 435 5.1 2.0 1.8
BOLD TYPE indicates maximum piercing parameters.

CUTMASTER A60
Stainless Steel
40A
Starter Cartridge
Standard Shield Cup
Cartridge
9-8218 9-8213
9-8243 9-8208 9-8232
9-8237 9-8277

Thickness (Air)
Height Height Speed
PSI
length)
18 0.050 110 0.19 60 0.20 0.00 0.07
16 0.063 100 0.19 50 0.20 0.00 0.07
14 0.078 105 0.19 45 0.20 0.10 0.07
12 0.109 110 0.19 40 0.20 0.20 0.07
75 (25')
10 0.141 108 0.19 35 0.20 0.30 0.07
80 (50')
3/16 0.188 110 0.19 30 0.20 0.40 0.07
1/4 0.250 120 0.19 18 0.20 0.50 0.08
3/8 0.375 126 0.19 10 0.20 2.00 0.08
1/2 0.500 118 0.19 8 Edge start 0.09

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 112 4.8 1670 4.8 0.0 1.7
2 105 4.8 1140 5.1 0.1 1.8
3 109 4.8 980 5.1 0.2 1.8
4 109 4.8 845 5.1 0.3 1.8
5.2 (7.6m)
5 111 4.8 715 5.1 0.4 1.8
6 5.5 (15.2m) 118 4.8 525 5.1 0.5 2.0
8 123 4.8 350 5.1 1.5 2.0
10 125 4.8 245 5.1 2.0 2.0
12 120 4.8 215 Edge Start 2.2
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.

CUTMASTER A60
Aluminum
40A
Starter Cartridge
Standard Shield Cup
Cartridge
9-8218 9-8213
9-8243 9-8208 9-8232
9-8237 9-8277

Thickness (Air)
Height Height Speed
PSI
length)
20 0.040 95 0.16 300 0.16 0.0 0.06

16 0.063 97 0.16 170 0.16 0.0 0.06
12 0.097 113 0.16 100 0.16 0.2 0.07
11 0.125 70 (25') 115 0.16 90 0.18 0.3 0.07
9 0.160 75 (50') 113 0.18 85 0.18 0.4 0.07
3/16 0.188 116 0.18 75 0.18 0.5 0.07
1/4 0.250 128 0.18 30 0.18 1.0 0.08
3/8 0.375 150 0.18 10 Edge Start 0.09

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1.0 95 4.1 7620 4.1 0.0 1.5
2.0 104 4.1 3500 4.1 0.2 1.6
3.0 115 4.1 2350 4.6 0.3 1.7
4.0 4.8 (7.6m) 113 4.6 2170 4.6 0.4 1.7
5.0 5.2 (15.2m) 118 4.6 1740 4.6 0.5 1.8
6.0 125 4.6 1015 4.6 0.8 1.9
8.0 139 4.6 500 Edge Start 2.0
10.0 153 4.6 180 Edge Start 2.2

CUTMASTER A60
Mild Steel
60A
Starter Cartridge
Standard Shield Cup
Cartridge
9-8218 9-8213
9-8243 9-8210 9-8232
9-8237 9-8277

Thickness (Air)
Height Height Speed
PSI
length)
16 0.060 118 0.19 290 0.19 0.00 0.08
14 0.075 120 0.19 285 0.19 0.10 0.08
11 0.120 118 0.19 180 0.19 0.10 0.08
10 0.135 119 0.19 176 0.19 0.10 0.07
3/16 0.188 121 0.19 100 0.19 0.20 0.08
85 (25')
1/4 0.250 122 0.19 80 0.19 0.30 0.08
90 (50')
3/8 0.375 124 0.19 50 0.19 0.50 0.09
1/2 0.500 132 0.19 26 0.19 0.75 0.10
5/8 0.625 135 0.19 19 Edge Start 0.10
3/4 0.750 136 0.19 14 Edge Start 0.08
1 1.000 150 0.19 6 Edge Start 0.11

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 115 4.8 7540 4.8 0 2.1
2 120 4.8 7015 4.0 0.10 1.9
3 118 4.8 4570 4.8 0.10 0.1
4 120 4.8 3650 4.8 0.20 1.9
5 121 4.8 2465 4.8 0.20 2.1
6 5.9 (7.6m) 122 4.8 2145 4.8 0.30 2.0
8 123 4.8 1635 4.8 0.40 2.2
6.2 (15.2m)
10 125 4.8 1180 4.8 0.60 2.4
12 130 4.8 795 4.8 0.75 2.4
15 134 4.8 530 Edge Start 2.4
20 138 4.8 325 Edge Start 2.2
25 149 4.8 165 Edge Start 2.7

CUTMASTER A60
Stainless Steel
60A
Starter Cartridge
Standard Shield Cup
Cartridge
9-8218 9-8213
9-8243 9-8210 9-8232
9-8237 9-8277

Thickness (Air)
Height Height Speed
PSI
length)
16 0.063 119 0.19 350 0.20 0.00 0.05
14 0.078 116 0.19 300 0.20 0.10 0.07
11 0.125 123 0.19 150 0.20 0.10 0.07
10 0.141 118 0.19 125 0.20 0.10 0.08
3/16 0.188 85 (25') 122 0.19 90 0.20 0.20 0.08
1/4 0.250 90 (50') 123 0.19 65 0.20 0.30 0.09
3/8 0.375 130 0.19 30 0.20 0.50 0.09
1/2 0.500 132 0.19 21 0.20 0.90 0.08
5/8 0.625 132 0.19 14 Edge Start 0.11
3/4 0.750 135 0.19 10 Edge Start 0.10

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 124 4.8 10890 5.1 0.00 0.8
2 116 4.8 7560 5.1 0.10 1.7
3 122 4.8 4365 5.1 0.10 1.7
4 119 4.8 2865 5.1 0.20 2.1
5 122 4.8 2195 5.1 0.20 2.1
5.9 (7.6m)
6 123 4.8 1790 5.1 0.30 2.2
8 6.2 (15.2m) 127 4.8 1190 5.1 0.40 2.2
10 130 4.8 725 5.1 0.50 2.2
12 132 4.8 580 5.1 0.90 2.1
15 132 4.8 405 Edge Start 2.6
20 136 4.8 230 Edge Start 2.5

CUTMASTER A60
Aluminum
60A
Starter Cartridge
Standard Shield Cup
Cartridge
9-8218 9-8213
9-8243 9-8210 9-8232
9-8237 9-8277

Thickness (Air)
Height Height Speed
PSI
length)
16 0.064 123 0.25 440 0.25 0.00 0.08
14 0.079 126 0.25 300 0.25 0.10 0.09
11 0.120 128 0.25 250 0.25 0.10 0.09
3/16 0.188 132 0.25 170 0.25 0.20 0.09
85 (25')
1/4 0.250 132 0.25 85 0.25 0.30 0.09
90 (50')
3/8 0.375 141 0.25 45 0.25 0.50 0.10
1/2 0.500 148 0.25 30 0.25 0.80 0.09
5/8 0.625 145 0.19 18 Edge Start 0.08
3/4 0.750 147 0.19 12 Edge Start 0.10

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 118 6.4 17010 6.4 0.00 1.8
2 126 6.4 7680 6.4 0.10 2.3
3 128 6.4 6410 6.4 0.10 2.3
4 130 6.4 5230 6.4 0.20 2.3
5 132 6.4 4010 6.4 0.20 2.4
5.9 (7.6m)
6 132 6.4 2640 6.4 0.30 2.4
8 6.2 (15.2m) 137 6.4 1630 6.4 0.40 2.4
10 142 6.4 1085 6.4 0.60 2.4
12 146 6.4 845 6.4 0.70 2.3
15 146 4.8 540 Edge Start 2.1
20 148 4.8 260 Edge Start 2.5

CUTMASTER A60
Mild Steel
80A
Starter Cartridge
Standard Shield Cup
Cartridge
9-8218 9-8213
9-8243 9-8211 9-8232
9-8237 9-8277

Thickness (Air)
Height Height Speed
PSI
length)
16 0.060 110 0.19 320 0.20 0.00 0.06
11 0.120 113 0.19 230 0.20 0.10 0.07

10 0.135 110 0.19 180 0.20 0.20 0.07
3/16 0.188 110 0.19 136 0.20 0.30 0.07
1/4 0.250 85 (25') 115 0.19 100 0.20 0.40 0.09
3/8 0.375 125 0.19 42 0.20 0.50 0.09
90 (50')
1/2 0.500 123 0.19 40 0.20 0.60 0.09
5/8 0.625 133 0.19 18 0.20 0.75 0.10
3/4 0.750 140 0.25 18 Edge Start 0.11
7/8 0.875 150 0.25 10 Edge Start 0.11
1 1.000 152 0.25 8 Edge Start 0.13

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 109 4.8 8915 5.1 0.00 1.5
2 111 4.8 7415 5.1 0.10 1.7
3 113 4.8 5915 5.1 0.10 1.8
4 110 4.8 4095 5.1 0.30 1.7
5 111 4.8 3325 5.1 0.30 1.8
6 5.9 (7.6m) 114 4.8 2745 5.1 0.40 2.2
8 120 4.8 1775 5.1 0.50 2.3
6.2 (15.2m)
10 125 4.8 1060 5.1 0.50 2.3
12 123 4.8 1025 5.1 0.60 2.3
15 130 4.8 610 5.1 0.75 2.5
20 143 6.4 395 Edge Start 2.7
25 152 6.4 210 Edge Start 3.2

CUTMASTER A60
Stainless Steel
80A
Starter Cartridge
Standard Shield Cup
Cartridge
9-8218 9-8213
9-8243 9-8211 9-8232
9-8237 9-8277

Thickness (Air)
Height Height Speed
PSI
length)
16 0.063 110 0.19 340 0.25 0.00 0.06
11 0.125 115 .0.19 300 0.25 0.10 0.06
10 0.141 115 0.19 280 0.25 0.10 0.06
3/16 0.188 115 0.19 140 0.25 0.20 0.07
85 (25')
1/4 0.250 118 0.19 100 0.25 0.30 0.08
90 (50')
3/8 0.375 119 0.19 45 0.25 0.40 0.08
1/2 0.500 124 0.19 26 0.25 0.80 0.10
5/8 0.625 133 0.19 16 Edge Start 0.10
3/4 0.750 136 0.19 10 Edge Start 0.11

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 108 4.8 9020 6.4 0.00 1.5
2 111 4.8 8380 6.4 0.00 1.5
3 114 4.8 7730 6.4 0.10 1.5
4 115 4.8 5865 6.4 0.20 1.6
5 115 4.8 3410 6.4 0.20 1.8
5.9 (7.6m)
6 117 4.8 2765 6.4 0.30 1.9
8 6.2 (15.2m)
119 4.8 1815 6.4 0.40 2.0
10 120 4.8 1070 6.4 0.60 2.1
12 123 4.8 765 6.4 0.80 2.3
15 131 4.8 475 Edge Start 2.5
20 137 4.8 205 Edge Start 3.0

CUTMASTER A60
Aluminum
80A
Starter Cartridge
Standard Shield Cup
Cartridge
9-8218 9-8213
9-8243 9-8211 9-8232
9-8237 9-8277

Thickness (Air)
Height Height Speed
PSI
length)
16 0.064 116 0.25 350 0.25 0.00 0.10
11 0.120 120 0.25 280 0.25 0.10 0.10
3/16 0.188 124 0.25 180 0.25 0.20 0.10
1/4 0.250 130 0.25 110 0.25 0.30 0.09
85 (25')
3/8 0.375 136 0.25 55 0.25 0.40 0.11
90 (50')
1/2 0.500 139 0.25 38 0.25 0.60 0.11
5/8 0.625 136 0.19 26 0.25 0.75 0.10
3/4 0.750 150 0.19 14 Edge Start 0.12
7/8 0.875 153 0.19 10 Edge Start 0.11

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 114 6.4 8890 6.4 0.00 2.4
2 117 6.4 8420 6.4 0.00 2.5
3 120 6.4 7170 6.4 0.10 2.5
4 122 6.4 5710 6.4 0.20 2.5
5 125 6.4 4315 6.4 0.20 2.5
5.9 (7.6m)
6 129 6.4 3190 6.4 0.30 2.4
8 6.2 (15.2m) 133 6.4 2070 6.4 0.40 2.5
10 136 6.4 1330 6.4 0.50 2.7
12 138 6.4 1060 6.4 0.50 2.9
15 137 4.8 745 6.4 0.75 2.5
20 151 4.8 325 Edge Start 3.0

CUTMASTER A60
This page intentionally blank.

CUTMASTER A60
This page intentionally blank.

CUTMASTER A60
4T.09 Recommended Cutting Speeds for Machine and Automated Torches With Shielded Tip
Mild Steel
40A
Starter Cartridge
Shield Cap Maximum Life Shield Cup Tip Heavy Duty Starter Electrode
Cartridge
9-8213
9-8245 9-8237 9-8208 9-8232
9-8277

Thickness (Air)
Height Height Speed
PSI
length)
20 0.036 107 0.16 130 0.16 0.0 0.06
16 0.060 113 0.16 120 0.16 0.0 0.06
14 0.075 108 0.16 90 0.16 0.1 0.06
12 0.105 111 0.16 75 0.16 0.2 0.06
75 (25')
10 0.135 114 0.16 65 0.16 0.3 0.07
80 (50')
3/16 0.188 115 0.16 65 0.16 0.4 0.07
1/4 0.250 118 0.16 45 0.16 0.5 0.07
3/8 0.375 123 0.16 23 0.16 1.2 0.08
1/2 0.500 128 0.16 18 0.16 2.0 0.08

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 108 4.1 3266 4.1 0.0 1.4
2 108 4.1 2239 4.1 0.0 1.5
3 112 4.1 1794 4.1 0.1 1.7
4 5.2 (7.6m) 114 4.1 1651 4.1 0.2 1.7
5 115 4.1 1578 4.1 0.3 1.7
5.5 (15.2m)
6 117 4.1 1256 4.1 0.4 1.7
8 121 4.1 853 4.1 0.5 1.7
10 124 4.1 565 4.1 1.2 1.8
12 127 4.1 485 4.1 2.0 1.9

CUTMASTER A60
Stainless Steel
40A
Starter Cartridge
Cartridge
9-8213
9-8245 9-8237 9-8208 9-8232
9-8277

Thickness (Air)
Height Height Speed
PSI
length)
18 0.050 110 0.16 60 4.1 0.0 0.06

16 0.063 108 0.16 50 4.1 0.1 0.07
14 0.078 114 0.16 45 4.1 0.1 0.07
12 0.109 113 0.16 40 4.1 0.2 0.07
75 (25')
10 0.141 116 0.16 35 4.1 0.3 0.07
80 (50')
3/16 0.188 115 0.16 30 4.1 0.4 0.07
1/4 0.250 118 0.16 20 4.1 1.2 0.07
3/8 0.375 125 0.16 15 4.1 1.8 0.08
1/2 0.500 127 0.16 10 4.1 2.0 0.08

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 109 4.1 1670 4.1 0.0 1.7
2 114 4.1 1140 4.1 0.1 1.8
3 114 4.1 980 4.1 0.2 1.8
4 5.2 (7.6m) 116 4.1 845 4.1 0.3 1.8
5 115 4.1 725 4.1 0.4 1.8
5.5 (15.2m)
6 117 4.1 565 4.1 0.5 2.0
8 122 4.1 440 4.1 1.5 2.0
10 125 4.1 360 4.1 1.8 2.0
12 127 4.1 280 4.1 2.0 2.2

CUTMASTER A60
Aluminum
40A
Starter Cartridge
Cartridge
9-8213
9-8245 9-8237 9-8208 9-8232
9-8277

Thickness (Air)
Height Height Speed
PSI
length)
20 0.040 110 0.19 300 0.20 0.0 0.06
16 0.063 113 0.19 170 0.20 0.1 0.07
12 0.097 120 0.19 100 0.20 0.2 0.07
11 0.125 75 (25') 125 0.19 90 0.20 0.3 0.07
9 0.160 80 (50') 126 0.19 85 0.20 0.4 0.07
3/16 0.188 128 0.19 70 0.20 0.5 0.07
1/4 0.250 137 0.19 30 0.20 1.0 0.08
3/8 0.375 145 0.19 10 0.20 2.0 0.09

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1.0 110 4.8 7660 5.1 0.0 1.6
2.0 116 4.8 3490 5.1 0.2 1.8
3.0 124 4.8 2350 5.1 0.3 1.8
4.0 5.2 (7.6m) 126 4.8 2170 5.1 0.4 1.8
5.0 5.5 (15.2m) 129 4.8 1630 5.1 0.6 1.8
6.0 135 4.8 990 5.1 1.0 1.9
8.0 141 4.8 500 5.1 1.6 2.0
10.0 146 4.8 180 5.1 2.1 2.3

CUTMASTER A60
Mild Steel
60A
Starter Cartridge
Cartridge
9-8213
9-8238 9-8237 9-8210 9-8232
9-8277

Thickness (Air)
Height Height Speed
PSI
length)
16 0.060 128 0.19 250 0.20 0.00 0.09
14 0.075 129 0.19 237 0.20 0.10 0.09
11 0.120 126 0.19 200 0.20 0.10 0.08
10 0.135 128 0.19 142 0.20 0.10 0.09
3/16 0.188 132 0.19 115 0.20 0.20 0.09
85 (25')
1/4 0.250 134 0.19 80 0.20 0.30 0.08
90 (50')
3/8 0.375 132 0.19 34 0.20 0.70 0.10
1/2 0.500 144 0.19 23 0.20 0.75 0.10
5/8 0.625 150 0.19 14 Edge Start 0.10
3/4 0.750 145 0.19 14 Edge Start 0.10
1 1.000 160 0.19 4 Edge Start 0.12

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 127 4.8 6804 5.1 0 2.2
2 129 4.8 5942 5.1 0.10 2.2
3 126 4.8 5080 5.1 0.10 0.1
4 130 4.8 3316 5.1 0.20 2.3
5 132 4.8 2794 5.1 0.20 2.2
5.9 (7.6m)
6 134 4.8 2230 5.1 0.30 2.1
8 6.2 (15.2m) 133 4.8 1425 5.1 0.40 2.3
10 134 4.8 822 5.1 0.60 2.5
12 141 4.8 646 5.1 0.75 2.5
15 148 4.8 419 Edge Start 2.6
20 147 4.8 318 Edge Start 2.7
25 159 4.8 118 Edge Start 3.0

CUTMASTER A60
Stainless Steel
60A
Starter Cartridge
Cartridge
9-8213
9-8238 9-8237 9-8210 9-8232
9-8277

Thickness (Air)
Height Height Speed
PSI
length)
16 0.063 110 0.13 165 0.20 0.00 0.06
14 0.078 116 0.13 155 0.20 0.10 0.07
11 0.125 118 0.13 125 0.20 0.10 0.07
10 0.141 126 0.13 80 0.20 0.10 0.09
3/16 0.188 85 (25') 125 0.13 75 0.20 0.20 0.09
1/4 0.250 90 (50') 127 0.13 60 0.20 0.30 0.08
3/8 0.375 134 0.13 28 0.20 0.50 0.08
1/2 0.500 136 0.19 17 0.25 0.75 0.09
5/8 0.625 131 0.13 14 Edge Start 0.08
3/4 0.750 142 0.19 10 Edge Start 0.11

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 101 3.3 4590 5.1 0.00 1.2
2 116 3.3 3925 5.1 0.10 1.7
3 118 3.3 3285 5.1 0.10 1.7
4 126 3.3 1985 5.1 0.20 2.2
5 5.9 (7.6m) 125 3.3 1850 5.1 0.20 2.1
6 127 3.3 1605 5.1 0.30 2.1
6.2 (15.2m)
8 131 3.3 1100 5.1 0.40 2.1
10 134 3.3 670 5.1 0.50 2.1
12 136 4.8 490 6.4 0.90 2.2
15 132 3.3 375 Edge Start 2.6
20 144 4.8 230 Edge Start 2.5

CUTMASTER A60
Aluminum
60A
Starter Cartridge
Cartridge
9-8213
9-8238 9-8237 9-8210 9-8232
9-8277

Thickness (Air)
Height Height Speed
PSI
length)
16 0.064 118 0.13 350 0.20 0.00 0.07
14 0.079 118 0.13 350 0.20 0.10 0.08
11 0.120 123 0.13 275 0.20 0.10 0.08
3/16 0.188 125 0.13 140 0.20 0.20 0.08
85 (25')
1/4 0.250 132 0.13 80 0.20 0.30 0.08
90 (50')
3/8 0.375 135 0.13 45 0.20 0.50 0.08
1/2 0.500 140 0.13 26 0.20 0.80 0.08
5/8 0.625 148 0.19 18 Edge start 0.10
3/4 0.750 155 0.19 12 Edge start 0.11

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 118 6.4 8890 6.4 0.00 2
2 118 6.4 8890 6.4 0.10 2.0
3 123 6.4 7070 6.4 0.10 2.1
4 124 6.4 5095 6.4 0.20 2.0
5 5.9 (7.6m) 126 6.4 3335 6.4 0.20 2.0
6 130 6.4 2370 6.4 0.30 2.0
6.2 (15.2m)
8 134 6.4 1570 6.4 0.40 2.0
10 136 6.4 1070 6.4 0.60 2.0
12 139 6.4 765 6.4 0.70 2.0
15 146 4.8 515 Edge start 2.4
20 157 4.8 260 Edge start 2.7

CUTMASTER A60
Mild Steel
80A
Starter Cartridge
Cartridge
9-8213
9-8239 9-8237 9-8211 9-8232
9-8277
Torch Kerf Width

Material Gas Pressure Initial Piercing
Arc Voltage Working Travel Speed Pierce Delay @ Rec.
Thickness (Air) Height
Height Speed
PSI
length)
16 0.060 115 0.13 280 0.20 0.00 0.06
11 0.120 112 0.13 190 0.20 0.10 0.06
10 0.135 110 0.13 176 0.20 0.20 0.06
3/16 0.188 122 0.19 135 0.20 0.30 0.08
1/4 0.250 127 0.19 100 0.20 0.40 0.09
85 (25')
3/8 0.375 134 0.19 40 0.20 0.50 0.10
90 (50')
1/2 0.500 136 0.19 36 0.20 0.60 0.10
5/8 0.625 145 0.19 18 Edge Start 0.11
3/4 0.750 147 0.19 14 Edge Start 0.11
7/8 0.875 146 0.19 10 Edge Start 0.12
1.000 1.000 152 0.187 8 Edge Start 0.13

CUTMASTER A60
Torch Kerf Width
Height Speed
Bar
length)
1 116 3.3 7895 5.1 0.00 1.6

2 114 3.3 6395 5.1 0.10 1.6
3 112 3.3 4895 5.1 0.10 1.5
4 115 4.8 4025 5.1 0.30 1.7
5 123 4.8 3300 5.1 0.30 2.0
5.9 (7.6m)
6 126 4.8 2735 5.1 0.40 2.2
8 6.2 (15.2m) 131 4.8 1745 5.1 0.50 2.5
10 134 4.8 1000 5.1 0.50 2.6
12 136 4.8 935 5.1 0.60 2.6
15 143 4.8 580 5.1 0.80 2.8
20 147 4.8 325 Edge Start 2.9
25 151 4.8 210 Edge Start 3.2

CUTMASTER A60
Stainless Steel
80A
Starter Cartridge
Cartridge
9-8213
9-8239 9-8237 9-8211 9-8232
9-8277
Torch Kerf Width

Height Speed
PSI
length)
16 0.063 114 0.125 340 0.2 0.00 0.06
11 0.125 115 0.125 260 0.2 0.10 0.06
10 0.141 116 0.125 250 0.2 0.10 0.06
3/16 0.188 115 0.125 170 0.2 0.20 0.07
85 (25')
1/4 0.250 118 0.125 85 0.2 0.30 0.08
3/8 0.375 90 (50') 127 0.19 45 0.25 0.40 0.09
1/2 0.500 136 0.19 16 0.25 0.75 0.11
5/8 0.625 143 0.19 10 Edge Start 0.12
3/4 0.750 146 0.19 8 Edge Start 0.11

CUTMASTER A60
Torch Kerf Width
Height Speed
Bar
length)
1 114 3.2 9410 5.1 0.00 1.5
2 114 3.2 8120 5.1 0.00 1.4
3 115 3.2 6830 5.1 0.10 1.4
4 116 3.2 5635 5.1 0.20 1.5
5 5.9 (7.6m) 115 3.2 4010 5.1 0.20 1.8
6 117 3.2 2640 5.1 0.30 2.0
6.2 (15.2m)
8 123 4.8 1630 6.4 0.40 2.1
10 128 4.8 1030 6.4 0.60 2.2
12 134 4.8 565 6.4 0.75 2.6
15 141 4.8 295 Edge Start 3.0
20 147 4.8 185 Edge Start 2.8

CUTMASTER A60
Aluminum
80A
Starter Cartridge
Cartridge
9-8213
9-8239 9-8237 9-8211 9-8232
9-8277

Thickness (Air)
Height Height Speed
PSI
length)
16 0.064 115 0.13 320 0.2 0.00 0.09

11 0.120 120 0.13 240 0.2 0.10 0.08
3/16 0.188 122 0.13 165 0.2 0.20 0.08
0.250 85 (25') 0.10
1/4 124 0.13 100 0.2 0.30
3/8 0.375 90 (50') 140 0.19 60 0.2 0.40 0.09
1/2 0.500 142 0.19 36 0.2 0.60 0.11
5/8 0.625 148 0.19 26 0.2 0.75 0.11
3/4 0.750 155 0.19 16 Edge Start 0.12

CUTMASTER A60
Thickness (Air)
Height Height Speed
Bar
length)
1 113 3.3 9020 5.1 0.00 2.4
2 116 3.3 7595 5.1 0.00 2.2
3 120 3.3 6165 5.1 0.10 2.0
4 121 3.3 5045 5.1 0.20 2.1
5 5.9 (7.6m) 122 3.3 3955 5.1 0.20 2.2
6 124 3.3 2905 5.1 0.30 2.3
6.2 (15.2m)
8 132 4.8 2010 5.1 0.40 2.3
10 140 4.8 1430 5.1 0.50 2.3
12 142 4.8 1045 5.1 0.60 2.6
15 146 4.8 730 5.1 0.75 2.7
20 157 4.8 330 Edge Start 3.2

CUTMASTER A60
PATENT INFORMATION
Plasma Cutting Torch Patents
The following parts are covered under U.S. and Foreign Patents as follows:
Catalog # Description Patent(s)
9-8215 Electrode US Pat No(s) 6163008; 6987238
Other Pat(s) Pending
9-8232 Electrode US Pat No(s) 6163008; 6987238
9-8213 Cartridge US Pat No(s) 6903301; 6717096; 6936786;
6703581; D496842; D511280; D492709; D499620;
D504142 Other Pat(s) Pending
9-8205 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8206 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8207 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8252 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8208 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8209 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8210 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8231 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8211 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8212 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8253 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8233 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8225 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8226 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8227 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8228 Tip US Pat No(s) 6774336; 7145099; 6933461
9-8241 Shield Cap US Pat No(s) 6914211; D505309
9-8237 Shield Cup US Pat No(s) 6914211; D501632; D511633

CUTMASTER A60
Catalog # Description Patent(s)
The following parts are also licensed under U.S. Patent No. 5,120,930 and 5,132,512:
Catalog # Description
9-8235 Shield Cap
9-8236 Shield Cap
9-8237 Shield Cup
9-8238 Shield Cap
9-8239 Shield Cap
9-8244 Shield Cap
9-8245 Shield Cap

CUTMASTER A60

CUTMASTER A60
SECTION 5 SYSTEM:
SERVICE
5.01 General Maintenance
Maintain more often
Warning! if used under severe
Disconnect input power before maintaining. conditions
Each Use
Visual check of
torch tip and electrode
Weekly
Visually inspect the

cables and leads.
Visually inspect the torch body tip, Replace as needed
electrode, start cartridge and shield cup
3 Months
Replace all
Clean
broken parts
exterior
of power supply
6 Months
Visually check and

Carefully clean the
interior
Art # A-07938_AB
Manual 0-4981 SERVICE 5-1

CUTMASTER A60
5.02 Maintenance Schedule 5.03 Common Faults
NOTE Problem - Symptom Common Cause
The actual frequency of maintenance may need to Insufficient 1. Cutting speed too fast.
be adjusted according to the operating environ- Penetration 2. Torch tilted too much.
ment. 3. Metal too thick.
4. Worn torch parts
Daily Operational Checks or Every Six Cutting Hours: 5. Cutting current too low.
6. Non - Genuine Victor Thermal
1. Check torch consumable parts, replace if damaged, Dynamics parts used
worn or when cut performance has diminished. 7. Incorrect gas pressure
2. Check plasma and secondary supply and pressure. Main Arc 1. Cutting speed too slow.
3. Purge plasma gas line to remove any moisture build-up. Extinguishes 2. Torch standoff too high from
workpiece.
3. Cutting current too high.
Weekly or Every 30 Cutting Hours:
4. Work cable disconnected.
1. Check fan for proper operation and adequate air flow. 5. Worn torch parts.
2. Inspect torch for any cracks or exposed wires, replace Dynamics parts used
if necessary.
Excessive Dross 1. Cutting speed too slow.
3. Inspect input power cable for damage or exposed wires,
Formation 2. Torch standoff too high from
replace if necessary.
workpiece.
3. Worn torch parts.
Six Months or Every 720 Cutting Hours: 4. Improper cutting current.
1. Check the in-line air filter(s), clean or replace as re- 5. Non - Genuine Victor Thermal
quired. Dynamics parts used
6. Incorrect gas pressure
2. Check cables and hoses for leaks or cracks, replace if
necessary. Short Torch Parts Life1. Oil or moisture in air source.
2. Exceeding system capability
3. Check all contactor points for severe arcing or pits, (material too thick).
replace if necessary. 3. Excessive pilot arc time
4. Gas pressure too low.
4. Vacuum dust and dirt out of the entire machine.
5. Improperly assembled torch.
Dynamics parts used
CAUTION
Difficult Starting 1. Worn torch parts.
Do not blow air into the power supply during 2. Non - Genuine Victor Thermal
cleaning. Blowing air into the unit can cause metal Dynamics parts used.
particles to interfere with sensitive electrical com- 3. Incorrect gas pressure.
ponents and cause damage to the unit.
5-2 SERVICE Manual 0-4981

CUTMASTER A60
5.04 Fault Indicator Explanation of Faults
UNDER PRESSURE: Indicates that operating pressure is
At initial power up, two lights will temporarily illuminate for 2-3
set too low and power supply output power will be
seconds to show the version of software used.
disabled.
To determine the first digit, count the function indicators left
INPUT POWER: Indicates primary line voltage is outside
to right, 1 through 5. To determine the second digit count the
the operating limits of the power supply as selected
pressure indicators, reading from bottom to top, 0 through 7.
by the setting of INPUT VOLTAGE SELECTION SWITCH
In the example below the Temp indicator and 75 psi indicators
at the rear of the unit. Low is 208/230 VAC and high
are on indicating the version would be 2.3.
is 460 VAC.
LO
7
6
HI
5 MIN
A
MAX
PSI
MAX
BAR
MAX
S
+
4
3 Art # A-08316
2
PART IN PLACE: Indicates that the shield cup is not prop-
1 MIN MIN
erly installed or tightened.

0
!
START ERROR: Indicates that the START SIGNAL was ac-
tive (ie. Torch Trigger depressed, hand held pendant
switch ON or CNC signal for torch ON) during one of
three conditions:
Art# A-07988 1) During initial power up when ON/OFF switch is
1 2 3 4 5
turned to ON position
When the ! "Fault" indicator is ON or blinking it will be 2) When fault which had been disabling the system
accompanied by one of the pressure indicator lights de- is cleared.
pending on what the Fault is. Only one of these faults will
3) When the FUNCTION CONTROL SWITCH Mode is
be displayed at one time. If more than one fault exists, when
moved from SET position to any of the other three
the first fault is corrected and cleared, the next fault will
(3) modes of operation.
then be displayed. It is possible to have a fault indicated
in the function indicators and another fault indicated in the CONSUMABLES MISSING: Indicates that the electrode,
pressure indicators. The following table shows each of the start cartridge or tip is missing or excessively worn.
Faults possible.
SHORTED TORCH: Indicates the torch or lead has a shorted
Pressure Fault condition between positive and negative leads.
Indicator
INTERNAL ERROR: Indicates a microprocessor error.
Max Over Pressure
90 Internal Error OVER PRESSURE: Indicates that operating pressure is set
too high. The Error Indicator will not flash when the
85 Shorted Torch pressure is above 95 PSI. This LED will remain ON
80 Consumables Missing and the system will operate but pilot starting and cut
75 Start Error performance may be affected.
70 Parts in Place NOTE
65 Input Power The cooling fans will turn ON as soon as the unit
Min Under Pressure is turned ON. After the unit is idle for ten (10)
minutes the fans will turn OFF. The fans will come
NOTE back ON as soon as the torch switch (Start Signal)
Fault explanations are covered in the following is activated or if the unit is turned OFF, then turned
tables. ON again. If an over temperature condition occurs,
the fans will continue to run while the condition
exists and for a ten (10) minute period once the
condition is cleared.

CUTMASTER A60
5.05 Basic Troubleshooting Guide
! WARNING
There are extremely dangerous voltage and power levels present inside this unit. Do not attempt to diagnose or repair
unless you have had training in power electronics measurement and troubleshooting techniques.
Problem - Symptom Possible Cause Recommended Action

ON / OFF Switch 1. Primary power disconnect is in 1. Turn primary power disconnect switch to ON position.
is ON but the A/C OFF position.
Indicator does not 2. Primary fuses / breakers are 2. a) Have a qualified person check primary fuses / breakers.
light blown or tripped. b) Connect unit to known good primary power receptacle
3. Faulty components in unit. 3. Return to authorized service center for repair or replacement.
FAULT indicator 1. INPUT VOLTAGE SELECTION 1. Turn OFF power to unit then set INPUT VOLTAGE SELECTION
flashing, 65 PSI SWITCH set for incorrect voltage. SWITCH to match primary input voltage.
indicator flashing 2. Primary input voltage problem. 2. Have a qualified person check primary voltage to insure it
meets unit requirements see Section 2.04.
3. Faulty components in unit. 3. Return to authorized service center for repair or replacement.
TEMPERATURE 1. Air flow through or around the 1. Refer to clearance information – Section 2.04
indicator ON. FAULT unit is obstructed.
indicator flashing. 2. Duty cycle of the unit has been 2. Allow unit to cool.
exceeded
3. Failed components in unit 3. Return to authorized service center for repair or replacement.
GAS indicator OFF, 1. Gas supply not connected to 1. Connect gas supply to unit.
FAULT and MIN unit.
pressure indicators 2. Gas supply not turned ON. 2. Turn gas supply ON.
flashing. 3. Gas supply pressure too low. 3. Set air supply inlet pressure to unit to 120 psi.
4. AIR PRESSURE CONTROL 4. Adjust regulator to set air pressure - see Section 4.02.
regulator set too low.
5. Failed components in unit. 5. Return to authorized service center for repair or replacement.
FAULT and 70 PSI 1. Shield Cup loose. 1. Hand tighten the shield cup until it is snug.
indicators flashing. 2. Torch not properly connected to 2. Insure torch ATC is securely fastened to unit.
power supply.
3. Problem in torch and leads PIP 3. Replace torch and leads or return to authorized service center
circuit. for repair or replacement.
FAULT and 75 PSI 1. Start signal is active when ON/ 1. Start can be active for one of the following:
indicators flashing. OFF SWITCH is turned to ON • Hand torch switch held closed
position. • Hand pendant switch held closed
• CNC START signal is active low
Release the START signal source
2. Problem in the torch and leads 2. Replace torch and leads or return to authorized service center
switch circuit. for repair or replacement.

CUTMASTER A60
Problem - Symptom Possible Cause Recommended Action
FAULT & 80 PSI 1. Torch shield cup is loose. 1. Tighten shield cup by hand. Do not overtighten.
indicators flashing. 2. Torch tip, electrode or starter 2. Turn OFF power supply. Remove shield cup. Install
Gas flow is cycling cartridge missing. missing parts.
ON and OFF. 3. Torch start cartridge is stuck. 3. Turn OFF power supply. Bleed down system pressure.
Remove shield cup, tip and start cartridge. Check start
cartridge lower end fitting for free movement. Replace if fitting
does not move freely.
4. Open conductor in torch leads. 4. Replace torch and leads or return to authorized service
center for repair or replacement.
5. Problem in the torch and leads 5. Replace torch and leads or return to authorized service
switch circuit. center for repair or replacement.
6. Failed components in unit. 6. Return to authorized service center for repair or
replacement.
Nothing happens 1. Problem in the torch and leads 1. Take Torch and Leads (Remote Pendant) to Authorized
when torch switch switch circuit (Remote pendant Repair Facility.
or remote switch switch circuit).
is closed (Or CNC 2. CNC Contoller device not 2. Contact Controller manufacturer.
START signal is providing Start signal.
active) No gas flow, 3. Failed components in unit. 3. Return to authorized service center for repair or
DC LED OFF. replacement.
FAULT and 85 PSI 1. Upper O-Ring on torch head is in 1. Remove shield cup from torch; check upper O-Ring
indicators flashing. wrong position. position; correct if necessary.
2. Torch starter cartridge is stuck. 2. Turn OFF power supply. Bleed down system pressure.
Remove shield cup, tip and starter cartridge. Check starter
cartridge lower end fitting for free movement. Replace if fitting
does not move freely.
3. Worn or faulty torch parts. 3. Inspect torch consumable parts. Replace if necessary.
4. Shorted Torch. 4. Replace torch and leads or return to an authorized service
center for repair.
5. Temporary Short indicated by 5 5. Release torch switch and reactivate.
blinks per second.
6. Power Supply Failure (Standard 6. Return to authorized service center for repair or
rate of blinking) replacement.
No Fault lights ON, 1. Failed components in unit. 1. Return to an authorized service center for repair.
no arc in torch.
FAULT and 85 PSI 1. Internal Error 1. Turn the ON / OFF switch OFF then back ON again. If that
indicators flashing does not clear the fault, return to an authorized service center
for repair.
Pilot arc is ON but 1. Work cable not connected to 1. Connect work cable.
cutting arc will not work piece.
establish 2. Work cable/connector broken. 2. Replace work cable.
3. Failed components in unit. 3. Return to an authorized service center for repair.
Torch cutting is 1. Incorrect current setting. 1. Check and adjust to proper setting.
diminished 2. Worn torch consumables. 2. Check torch consumables and replace as needed.
3. Poor work cable connection to 3. Check the connection of the Work Lead to the work piece.
work piece.
4. Torch being moved too fast. 4. Reduce cutting speed.
5. Excessive oil or water in torch. 5. Refer to "Check air quality" in Section 3 Torch.
6. Failed components in unit. 6. Return to an authorized service center for repair.

CUTMASTER A60
5.06 Circuit Fault Isolation C. Filter Element Assembly Replacement
The Filter Element Assembly is in the rear panel. For better
system performance, the filter element should be checked
WARNING per the Maintenance Schedule (Subsection 5.02), and either
cleaned or replaced.
The following procedures should not be attempted
by anyone who has not had proper training or 1. Remove power from the power supply; turn OFF the
authorized to do so. gas supply and bleed down the system.
2. Remove the system cover. See "A Cover Removal" in
A. Cover Removal this section.
1. Remove the upper and lower screws which secure the 3. Locate the internal air line and the fitting from the filter
cover to the main assembly. Do not loosen the lower assembly. Number 1 in the following illustration.
screws inside the cut out slots in the bottom of the 4. Hold a wrench or similar tool against the locking ring
cover. on the filter assembly fitting, then pull on the hose to
NOTE release it. (Numbers 2 and 3 in the following illustra-
tion).
The upper screws and lower screws are not the
same. Do not mix them. The upper screws are
for threading into the plastic of the front and rear
panels. DO NOT use the finer threaded lower
screws for this.
1
Upper
Screws
Lower
Screws
Slots
Art # A-07989
Lower
Screws
Art # A-08317
3 4
5
2. Carefully pull the Cover up and away from the unit.
6mm
B. Cover Installation
1. Reverse previous procedures for cover installation.
5. Remove the fitting from the filter element assembly
NOTE by inserting a 6 mm hex wrench into the internal hex
When installing the upper screws, attempt to reuse fitting and turning it counter clock-wise (left). Numbers
the original threads. The easiest way to do this is 4 and 5 in the previous illustration.
by turning the screw counter-clockwise until you
feel the threads line up, then begin to turn the 6. Disconnect the input line from the filter element as-
screw clockwise to tighten to 15-18 in. lbs. Do sembly.
not over tighten. 7. Remove the filter element assembly through the rear
opening.

CUTMASTER A60
NOTE
If replacing or cleaning just the filter element refer Housing
to the following illustration for disassembly.
Filter
Element
(Cat. No. 9-7741)
Filter Element Spring
O-ring
(Cat. No. 9-7743) Assembled Filter
Cover
Barbed
Fitting Art # A-02476
Optional Single-Stage Filter Element Replacement

Art # A-07990
5. Remove the Filter Element from the Housing and set
8. Install the new or cleaned assembly by reversing these Element aside to dry.
procedures.
6. Wipe inside of housing clean, then insert the replace-
9. Turn ON the air supply and check for leaks before ment Filter Element open side first.
reinstalling the cover.
7. Replace Housing on Cover.
Optional Single-Stage Filter Element Replacement 8. Reattach gas supply.
These instructions apply to power supplies where the optional
NOTE
Single-Stage Filter has been installed.
If unit leaks between housing and cover, inspect
The Power Supply shuts down automatically when the Filter the O-Ring for cuts or other damage.
Element becomes completely saturated. The Filter Element
can be removed from its housing, dried, and reused. Allow 24 Optional Two-Stage Filter Element Replacement
hours for Element to dry. Refer to Section 6, Parts Lists, for
replacement filter element catalog number. The Two-Stage Air Filter has two Filter Elements. When the Filter
Elements become dirty the Power Supply will continue to oper-
1. Remove power from power supply. ate but cut quality may become unacceptable. Refer to Section
2. Shut OFF air supply and bleed down system before 6, Parts Lists, for replacement filter element catalog number.
disassembling Filter to change Filter Element. 1. Shut OFF primary input power.
3. Disconnect gas supply hose. 2. Shut OFF air supply and bleed down system.
4. Turn the Filter Housing Cover counter-clockwise and
remove it. The Filter Element is located inside the
Housing. WARNING
Always turn OFF the air supply and bleed the system
before disassembling the Filter Assembly as injury
could result.
3. Loosen the two bolts on the top of the Filter Assembly

enough to allow the Filter Elements to move freely.
4. Note the location and orientation of the old Filter Ele-
ments.
5. Slide out the old Filter Elements.

CUTMASTER A60
First & Second

Stage
Cartridges
(as marked)
Art # A-02942
Optional Two-Stage Filter Replacement
6. Slide the replacement Filter Elements into the Filter

Assembly, with the same orientation as noted in Step
4 above.
7. Hand tighten the two bolts evenly, then torque each
bolt to 20 - 30 in-lbs (2.3 - 3.4 Nm). Improper torque
may damage the gasket.
8. Slowly apply air pressure to the assembly, checking
for leaks.
NOTE
A small amount of air leakage from the bottom
fitting is normal.
This completes the parts replacement procedures.

CUTMASTER A60
SECTION 5 TORCH:
SERVICE
Upper Groove
5T.01 General Maintenance with Vent Holes
Must Remain Open
NOTE
Refer to Previous "Section 5 System: Service" for Upper O-Ring
common and fault indicator descriptions. in Correct Groove
Threads
Cleaning Torch
Lower O-Ring Art # A-03725
Even if precautions are taken to use only clean air with a Torch Head O-Ring
torch, eventually the inside of the torch becomes coated
with residue. This buildup can affect the pilot arc initiation
and the overall cut quality of the torch.
ATC Male Connector
WARNING
Disconnect primary power to the system before
DO NOT touch any internal torch parts while the AC
indicator light of the Power Supply is ON.
The inside of the torch should be cleaned with electrical

contact cleaner using a cotton swab or soft wet rag. In
severe cases, the torch can be removed from the leads
and cleaned more thoroughly by pouring electrical con- Gas Fitting
tact cleaner into the torch and blowing it through with
compressed air.
CAUTION
Dry the torch thoroughly before reinstalling.
O-Ring Lubrication Art #A-03791 O-Ring

An o-ring on the Torch Head and ATC Male Connector ATC O-Ring
requires lubrication on a scheduled basis. This will allow
the o-rings to remain pliable and provide a proper seal. NOTE
The o-rings will dry out, becoming hard and cracked if the
DO NOT use other lubricants or grease, they may
lubricant is not used on a regular basis. This can lead to
not be designed to operate within high tempera-
potential performance problems.
tures or may contain “unknown elements” that
It is recommended to apply a very light film of o-ring lubri- may react with the atmosphere. This reaction can
cant (Catalog # 8-4025) to the o-rings on a weekly basis. leave contaminants inside the torch. Either of these
conditions can lead to inconsistent performance or
poor parts life.
Manual 0-4981 SERVICE 5T-1

CUTMASTER A60
4. Remove the tip. Check for excessive wear (indicated
5T.02 Inspection and Replacement of
by an elongated or oversized orifice). Clean or replace
Consumable Torch Parts the tip if necessary.
Good Tip Worn Tip
WARNING
Disconnect primary power to the system before
DO NOT touch any internal torch parts while the AC A-03406
indicator light of the Power Supply is ON. Example of Tip Wear
5. Remove the starter cartridge. Check for excessive wear,

Remove the consumable torch parts as follows: plugged gas holes, or discoloration. Check the lower
NOTE end fitting for free motion. Replace if necessary.
Spring-Loaded Spring-Loaded
The shield cup holds the tip and starter cartridge
Lower End Fitting Lower End Fitting at Reset /
in place. Position the torch with the shield cup Full Compression Full Extension
facing upward to prevent these parts from falling
out when the cup is removed.
1. Unscrew and remove the shield cup from the torch.
NOTE
Slag built up on the shield cup that cannot be re-
moved may effect the performance of the system. Art # A-08064_AC
2. Inspect the cup for damage. Wipe it clean or replace 6. Pull the Electrode straight out of the Torch Head. Check
if damaged. the face of the electrode for excessive wear. Refer to
the following figure.
Art # A-08067
New Electrode
Shield Cups
3. On torches with a shield cup body and a shield cap or

deflector, ensure that the cap or deflector is threaded Worn Electrode
snugly against the shield cup body. In shielded drag Art # A-03284
cutting operations (only), there may be an O-ring Electrode Wear

between the shield cup body and drag shield cap. Do
not lubricate the O-ring. 7. Reinstall the Electrode by pushing it straight into the
Drag Shield Cap torch head until it clicks.
8. Reinstall the desired starter cartridge and tip into the
Shield
Cup Body torch head.
9. Hand tighten the shield cup until it is seated on the
torch head. If resistance is felt when installing the cup,
check the threads before proceeding.
O-Ring No. 8-3488
This completes the parts replacement procedures.
Art # A-03878
5T-2 SERVICE Manual 0-4981

CUTMASTER A60
SECTION 6:
PARTS LISTS
6.01 Introduction
A. Parts List Breakdown

The parts list provide a breakdown of all replaceable components. The parts lists are arranged as follows:
Section "6.03 Power Supply Replacement"

Section "6.04 Replacement Power Supply Parts"
Section "6.05 Options and Accessories"
Section "6.06 Torch Replacement Parts SL100SV Torch (w/Solenoid on Mounting Tube)"
Section "6.07 Torch Consumable Parts Automation / Machine (SL100)Torch"
Section "6.08 Torch Consumable Parts Manual (SL60)Torch"
Section "6.09 Replacement Parts for Hand Torch"
NOTE
Parts listed without item numbers are not shown, but may be ordered by the catalog number shown.
B. Returns
If a product must be returned for service, contact your distributor. Materials returned without proper authorization will not be
accepted.
6.02 Ordering Information

Order replacement parts by catalog number and complete description of the part or assembly, as listed in the parts list for each
type item. Also include the model and serial number of the power supply. Address all inquiries to your authorized distributor.
6.03 Power Supply Replacement

The following items are included with the replacement power supply: work cable & clamp, input power cable, gas pressure regula-
tor / filter, and operating manual.
Qty Description Catalog #
1 CutMaster A60 Power Supply
208/230 - 460VAC, Single or 3 Phase, 60Hz,
With input power cable and plug 3-1134-1
460VAC, Single or 3 Phase, 60Hz,
With input power cable 3-1134-2
400/415VAC, 3 Phase, 50Hz, with input power cable 3-1134-3
600VAC, 3 Phase, 60Hz, with input power cable 3-1134-5
Manual 0-4981 PARTS LIST 6-1

CUTMASTER A60
6.04 Replacement Power Supply Parts
1 Regulator 9-0115*
1 Filter Assembly Replacement Element 9-0116
1 Input Power Cord for 208 / 230 V Power Supply 9-8596
1 Input Power Cord for 400 V Power Supply 9-0218
1 Input Power Cord for 460/600 V Power Supply 9-8593
NOTE
*9-0115 regulator, If the serial number of the power supply is prior to #05078755 then kit number 9-0201 will be
needed to replace not only the regulator (9-0115) but the logic PCB as well. Another way to tell if the kit is needed is
to see if the regulator has a small diameter tube coming out of the bottom fitting. If there is a transducer and wire
harness instead of the tube, the kit is not needed.
6.05 Options and Accessories

1 Single - Stage Filter Kit (includes Filter & Hose) 7-7507
1 Replacement Filter Body 9-7740
1 Replacement Filter Hose (not shown) 9-7742
2 Replacement Filter Element 9-7741
1 Two - Stage Filter Kit (includes Hose & Mounting Screws)
1 Bracket, Filter Mounting (not shown)
1 Two - Stage Air Filter Assembly 9-7527
1 First Stage Cartridge 9-1021
1 Second Stage Cartridge 9-1022
1 Extended Work Cable (50 ft / 15.2 m) with Clamp 9-8529
1 Multi - Purpose Cart 7-8888
1 Automation Harness for Start/Stop and OK to move 9-9385
1 25' / 7.6 m CNC Cable for Automation Interface Kit 9-1008
1 35' / 10.7 m CNC Cable for Automation Interface Kit 9-1010
1 50' /15.2 m CNC Cable for Automation Interface Kit 9-1011
1 Nylon Dust Cover 9-7071

Housing
Filter
Element
(Cat. No. 9-7741)
Spring
O-ring
(Cat. No. 9-7743) Assembled Filter First & Second
Stage
Cover Cartridges
(as marked)
Barbed
Fitting Art # A-02476 Art # A-02942
Optional Single - Stage Filter Kit Optional Two - Stage Filter Kit
6-2 PARTS LIST Manual 0-4981

CUTMASTER A60
6.06 Torch Replacement Parts SL100SV Torch (w/Solenoid on Mounting Tube)
Item No. Qty Description Catalog No.
1 1 Torch Head Assembly without leads (includes items 2, 3, and 14) 9-8220
2 1 Large O-ring 8-3487
3 1 Small O-ring 8-3486
4 1 PIP Switch Kit 9-7036
5 1 PIP Plunger and Return Spring Kit 9-7045
6 Automated Leads Assemblies with ATC connectors
1 25 - foot / 7.6 m Leads Assembly with ATC connector 4-3058
7 1 Rack 9-9448
8 1 Mounting Tube 9-9445
9 1 End Cap Assembly 9-7044
10 2 Body, Mounting, Pinch Block 9-4513
11 1 Pin, Mounting, Pinch Block 9-4521
12 1 Torch Holder Sleeve 7-2896
13 1 Pinion Assembly (does not include positioning tube) 7-2827
14 1 Torch Holder Sleeve 7-2896
15 1 Pinion Gear-Short 8-6074
16 1 Handwheel (Torch Holder) 9-4514
17 1 Low Profile Torch Holder (1 3/8 Dia) w/o Hardware 9-4515
18 1 Calibrated Torch Holder Bushing 9-4366
19 1 5/32 Dia x 5/8 Lg Slotted Spring Pin See Note 1
20 1 3/8-24 x 3/8 Soc Hd Set Screw, Cup Point See Note 1
21 2 1/4-20 x 5/8 Hex Socket Head Screw See Note 1
22 1 #10-24 x 3/8 Hex Socket Set Screw, Cup Point See Note 1
23 1 Solenoid Assembly 9-9447
24 1 Solenoid Cover 9-9446
25 SL100SV Automation Torch and Leads Packages
25 - foot 7-4001
35 - foot 7-4002
50 - foot 7-4003
NOTE
Purchase these parts locally.

CUTMASTER A60
24 23
10
7
13
21
20
21
19
10 16
1
2 11
3
12
4
17
5 15
22
18
14
Art # A-07113

CUTMASTER A60
6.07 Torch Consumable Parts Automation / Machine (SL100)Torch
Ohmic Clip
Automation Torch
Ohmic Clip 9-8224
Manual Torch
9-8259
20-40A Shield
Tip: Shield Cap, Machine
Cup Body,
STANDOFF 40A 9-8245
9-8237
CUTTING
20A 9-8205 Shield Cup Shield Cap, Deflector

30A 9-8206 9-8218 9-8243
40A 9-8208
Drag Shield Cup

9-8235
50-60A Shield
Tips:
Cup Body,
STANDOFF Shield Cap, Machine
CUTTING 9-8237
50-60A 9-8238
50-55A 9-8209 Shield Cup

60A 9-8210 9-8218 Shield Cap, Deflector
9-8243
Drag Shield Cup

70-100A 9-8236
Electrode Starter Heavy Duty
Auto 9-8232 Cartridge Starter Cartridge Tips: Shield Drag Shield Cup
Manual 9-8215 9-8213 Non HF Only 9-8277 Cup Body, 120A 9-8258
9-8237
Shield Cap, Machine
70-100A 9-8239
70-120A 70A 9-8231
STANDOFF 80A 9-8211 Shield Cup Shield Cap, Machine
CUTTING 90/100A 9-8212 9-8218 120A 9-8256
120A Auto 9-8233
120A Manual 9-8253
Shield Cap, Deflector
9-8243
40-120A
GOUGING Shield
Cup Body,
9-8237
Tips:
Tip A 9-8225 (40 Amps Max.) Shield Cup, Gouging

9-8241
Tip B 9-8226 (50 - 120 Amps)
Tip C 9-8227 (60 - 120 Amps)
Tip D 9-8228 (60 - 120 Amps)

Art # A-08066_AG Tip E 9-8254 (60 - 120 Amps)

CUTMASTER A60
6.08 Torch Consumable Parts Manual (SL60)Torch
Tips: Shield
DRAG TIP Cup Body, Shield Cap, Deflector
CUTTING 9-8237 9-8243
20A 9-8205
30A 9-8206 Shield Cup
40A 9-8207 9-8218
60A 9-8252
O-Ring No. 8-3488 Shield Cap, Drag
DRAG SHIELD
40A 9-8244
CUTTING Shield
40A Cup Body,
CUTTING Tip:
9-8237
9-8243
40A 9-8208 Standoff Guide

Shield Cup 9-8251
STANDOFF
9-8218
CUTTING
O-Ring No. 8-3488 Shield Cap, Drag
DRAG SHIELD
CUTTING Shield 50-60A 9-8235
50-60A Tips:
Cup Body,
CUTTING 9-8237
9-8243
Start
Cartridge 50-55A 9-8209
Shield Cup Standoff Guide
9-8213 60A 9-8210 9-8281
9-8218
STANDOFF
CUTTING
DRAG SHIELD O-Ring No. 8-3488

Shield Cap, Drag
Electrode CUTTING Shield 70-100A 9-8236
9-8215 70-120A Tips: Cup Body,
CUTTING 9-8237 Shield Cap, Deflector
9-8243
70A 9-8231
80A 9-8211 Shield Cup Standoff Guide
90/100A 9-8212 9-8218 9-8281
120A 9-8253
STANDOFF CUTTING
40-120A
GOUGING Shield Shield Cap, Gouging
Cup Body, 9-8241
9-8237
Tips:
Tip Gouging A 9-8225 (40 Amps Max.)
NOTE
Tip Gouging B 9-8226 (50 - 100 Amps) CutMaster 52 uses 60A and less
CutMaster 82 uses 80A and less
Art # A-08065_AE CutMaster 102 uses 100A and less
Tip Gouging C 9-8227 (60 - 120 Amps)
CutMaster 152 uses 120A and less
Tip Gouging D 9-8228 (60 - 120 Amps)
Tip Gouging E 9-8254 (60 - 120 Amps)

CUTMASTER A60
6.09 Replacement Parts for Hand Torch
Item # Qty Description Catalog #
1 1 Torch Handle Replacement Kit (includes items No. 2 & 3) 9-7030
2 1 Trigger Assembly Replacement Kit 9-7034
3 1 Handle Screw Kit (5 each, 6-32 x 1/2” cap screw, and wrench) 9-8062
4 1 Torch Head Assembly Replacement Kit (includes items No. 5 & 6) 9-8219
5 1 Large O-ring 8-3487
6 1 Small O-ring 8-3486
7 Leads Assemblies with ATC connectors (includes switch assemblies)
1 SL60, 20 - foot Leads Assembly with ATC connector 4-7834
8 1 Switch Kit 9-7031
5
6
3
Art # A-07993_AB

CUTMASTER A60

CUTMASTER A60
APPENDIX 1: SEQUENCE OF OPERATION
(BLOCK DIAGRAM)
ACTION: ACTION: ACTION: ACTION:
ON / OFF switch to ON RUN / Rapid Auto Restart /
Close external RUN / SET / LATCH
disconnect switch. Rapid Auto Restart /
RESULT: switch to RUN
RESULT: SET / LATCH switch
AC indicator ON. to SET (for most applications)
Power to system. or to
GAS indicator ON Rapid Auto Restart
when input RESULT:
pressure is adequate (for gouging, trimming,
for power supply operation. Gas flows to set or expanded metal
pressure. applications)
Power circuit ready.
or to
LATCH
is used for specific applications

(torch switch can be released
after main arc transfer).
ACTION: RESULT: Gas flow stops.
Connect work cable to workpiece.

Set output amperage. ACTION:
RESULT:
Torch moved away from work (while
System is ready still activated).
for operation.
RESULT:
Main arc stops.

Pilot arc automatically
ACTION:
restarts.
Protect eyes and activate
Torch switch (START) PILOT ARC
RESULT:
Fans turn on. Gas flows briefly, ACTION:

then stops.Gas restarts.
Torch moved within
DC indicator ON transfer distance of workpiece.
Pilot arc established.
RESULT:
Main arc transfers.

Pilot arc off.
ACTION:
Release Torch switch.
RESULT: ACTION:
ACTION:
Main arc stops. Unplug input
Gas flow stops after post - flow. ON / OFF switch power cord or
to OFF open external
(Fans will continue to run for disconnect.
10 minutes after the Torch switch RESULT:
[START] is removed) RESULT:
All indicators off. No power to system.
Power supply fans shut off.
Art #A-07979_AB
Manual 0-4981 APPENDIX A-1

CUTMASTER A60
APPENDIX 2: DATA TAG INFORMATION
West Lebanon, NH USA 03784 Manufacturer's Name and/or

Logo, Location, Model and
Model : Revision Level, Serial Number
S/N
and Production Code
Dat e of Mf r : Made in USA
Type of Power Regulatory Standard Covering
Supply (Note 1) 1/ 3 f1
f2 This Type of Power Supply
Output Current Type Duty Cycle Factor

Output Range (Amperage/
Voltage)
Plasma Cutting
Symbol X
I Duty Cycle Data (Note 3)
U0 =
U2
Rated No- Conventional
Load Voltage Load Voltage
Rated Maximum
Supply Current
Input Power
Symbol
U1 I 1max 3Ø I 1eff Maximum Effective
1
1Ø 1
1Ø 3Ø
Supply Current
Input Power
Specifications
(Phase, AC or DC
Hertz Rating) Manufacturer's Electrical
Schematic File Number
and Revision Level
Degree of Protection Rated Supply
Voltage (Note 2)
NOTES:
1. Symbol shown indicates single- or three-phase AC input, Standard Symbols
static frequency converter-transformer-rectifier, DC output. AC
2. Indicates input voltages for this power supply. Most power
supplies carry a label at the input power cord showing input DC
voltage requirements for the power supply as built. Ø Phase
3. Top row: Duty cycle values.
IEC duty cycle value is calculated as specified by
the International ElectroTechnical Commission. Art # A-03288_AB
TDC duty cycle value is determined under the power supply
manufacturer's test procedures.
Second row: Rated cutting current values.
Third row: Conventional load voltage values.
4. Sections of the Data Tag may be applied to separate areas
of the power supply.
A-2 APPENDIX Manual 0-4981

CUTMASTER A60
APPENDIX 3: TORCH PIN - OUT DIAGRAMS
A. Automation SL100SV Torch Pin - Out Diagram
ATC Male Connector - ATC Female Receptacle -
Front View Front View
Negative / Plasma Negative / Plasma
4 - Not Used
8 - Open
4- Open 8 - Open
7 - Green / 7 - Torch 3 - Not Used

8 4
3 - Open 4 8 - Torch Solenoid
Solenoid 7 3
3 7 6 2
2 6 2 - PIP Circuit
6 - Open 6 - Open 5 1
2 - Orange / 1 5
PIP
5 - White / 5 - Torch 1 - PIP Circuit
1 - Black / - Torch Solenoid
PIP Solenoid Pilot
Pilot
Art # A-07114
B. Machine SL100 Torch Pin - Out Diagram

ATC Male Connector UNSHIELDED MACHINE TORCH ATC Female Receptacle
Front View Front View
Negative / Plasma
Negative / Plasma
8 - Green -
4- Black -
Pendant
Pendant
Connector 8 - Ground 4 - Switch
Connector
Ground
3 - White -
4 8 7 - Green / 3 - Switch
Pendant 7 - Open 8 4
3 7 Not Used
Connector 7 3
2 6 6 2
6 - Open
2 - Orange / 1 5 5 1
6 - Open 2 - PIP
PIP
5 - White / 1 - PIP
1 - Black / 5 - Open
Not Used
PIP
Pilot Pilot
Art # A-03799
C. Hand Torch Pin - Out Diagram

ATC Male Connector ATC Female Receptacle
Negative / Front View Front View Negative /
Plasma Plasma
4 - Green / 8 - Open 8 - Ground

Switch 4 - Switch
7 - Open 7 - Open 3 - Switch

3 - White / 4 8 8 4
Switch 3 7 7 3
2 6 6 - Open 6 2
2- Orange / 6 - Open
1 5 5 1 2 - PIP
PIP
5 - Open 5 - Open
1 - PIP
1 - Black /
PIP Pilot
Pilot A-03701

CUTMASTER A60
APPENDIX 4: TORCH CONNECTION DIAGRAMS
A. Automation (SL100SV) Torch Connection Diagram
Automated CutMaster Power Supply with ATC Torch Receptacle,
Automated SL100SV Torch (w/ Solenoid on Positioning Tube), Torch Lead with ATC Connector
ATC Male ATC Female
Torch Leads Connector Torch Receptacle
Torch Head Torch Leads Power Supply

Socket
Pin No.s No.s
PIP Black 1 1 Main PC Board
Switch Orange 2 2 Main PC Board
White 5 5 Main PC Board
4 4
Not Connected
3 3
Green 7 7 Main PC Board
6 6 Not Connected
Solenoid 8 8
Negative / Plasma Lead
Pilot Lead
Art # A-07115
B. Machine (SL100) Torch Connection Diagram

Torch: Unshielded Mechanized SL100 Machine Torch
Leads: Leads with ATC Connector and
Remote Pendant Connector To Remote Control
Power Supply: with ATC Female Receptacle
Remote
Male ATC Female
Pendant
ATC Leads Receptacle
Connector
Connector
Power
Torch Torch Supply
Head Leads
PIP Black 1 1 To Power Supply
Switch Orange 2 2 Circuitry
White 5 5
6 6
Not Black 4 4 To Power Supply
Used
White 3 3 Circuitry
Green 8 8
Green 7 7
Negative / Plasma Lead Negative / Plasma
Pilot Lead
Pilot
Art # A-03798

CUTMASTER A60
C. Hand Torch Connection Diagram
Torch: SL60 / SL100 Hand Torch

Leads: Torch Leads with ATC Connector
Power Supply: with ATC Receptacle Male
ATC Leads ATC Female
Connector Receptacle Power
Torch Torch Supply
Head Leads
PIP Black 1 1 To Power Supply
Switch Orange 2 2 Circuitry
5 5
6 6
Torch Green 4 4 To Power Supply
Switch White 3 3 Circuitry
8 8
7 7
Negative / Plasma Negative / Plasma
Pilot
Pilot
Art # A-03797

CUTMASTER A60
APPENDIX 5: SYSTEM SCHEMATIC, 208/460V UNITS
5 4 3 2
J3
1
2
3
T1
K5, K6 K1-K4
J12
1
2
3
PRI 2 PRI 1 PRI 4 PRI 3
+12VDC
D
B A D C
/460
/230
BIAS
SUPPLY
J1 MTH1 MTH2
SW1
1 3 1
2
3 Q1
4
2 4 5
K1
RESISTORS
INRUSH
C1-C4* +
/INRUSH
D1
MTH3 MTH4
W1
AC1
* PRIMARY L1 7
AC INPUT L1 T1
AC2
L2 8
K1 K2 K5 K6 K3 K4
L2 T2
JUMPER AC3
L3 9
L3 T3
GND 7A
L4 T4 MTH6 MTH8
Q2
C
*PRIMARY POWER CONNECTIONS:

3PH USE L1,L2,L3 & GND + C5-C8*
REMOVE JUMPER BETWEEN L2 TO L3
1PH USE L1, L2 & GND -

INSTALL JUMPER BETWEEN L2 TO L3
SW2
J3 MTH5 MTH7
1 460_IN
2
INPUT VOLTAGE SELECTOR * CM52 & A40
(Closed for 230VAC input) C3 & C5 not installed
24VAC
PCB2 INPUT CAPACITOR PCB
5
J6
TEST POINTS
W1 1
2 24 VAC RETURN
GND1 COMMON
GND2 COMMON
GND3 COMMON
6 +12V1 +12 VDC SUPPLY
48V1 +48 VDC SUPPLY
I_DMD_1 CURRENT DEMAND
J4 D59 PCR TIP_SEN TIP DRAG SENSE
1 3.3VDC
2 TXD
SERIAL PORT RXD
3
4 D78 CSR +12VDC
B 5 D
PCB1 MAIN PCB ASSY

/SOLENOID
J5
1
2
3
J2
40 CIRCUIT
RIBBON CABLE
J1
40 PIN RIBBON CABLE SIGNALS

SOL1
1 -V_OUT_SIGNAL M-L
2 /TIP_VOLTS M-L ERROR IND FAULT MAX
3 /TIP_SENSE M-L AC
4 /460V_IN L-M MAX OVER PRESSURE
5 /230V_IN L-M 90 INTERNAL ERROR
6 CUR_SET L-M 85 SHORTED TORCH 90
7 /RAR (RAPID AUTO RESTART) L-M OVERTEMP 80 CONSUMABLES MISSING
8 /INRUSH L-M 75 START ERROR
9 /W1_ON L-M 70 PARTS IN PLACE
10 /SHDN L-M 65 INPUT POWER 85
11 /TORCH_SOLENOID L-M GAS MIN UNDER PRESSURE
12 /SOLENOID_ON L-M
13 /OK_TO_MOVE L-M
14 /FAN_ON L-M TEST POINTS 80
DC
15 /LATCH_ACTIVE L-M
TP1 GND
16 /TORCH_SWITCH M-L
TP2 +12 VDC
17 /PIP M-L
TP3 +5 VDC 75 GAS CONTROL
18 AC_ON M-L ERROR TP4 3.3 VDC
19 CSR M-L
TP5 0.v - 5.0 VDC / 0-100PSI
20 /TORCH_SOLENOID_DETECT M-L REGULATOR
TP6 1.8 VDC SOLENOID
21 /OVERTEMP M-L 70 ATC
TP7 POT. DEMAND VALVE
A
22 V_IN M-L
23 +12VDC M-L
24 +12VDC M-L
25 COMMON M-L Current Control 65 FILTER
26 COMMON M-L +12VDC AIR
29 MAIN_PCB_ID M-L INLET
34 460_IN M-L
35 +3.3VDC L-M D1 MIN
LATCH PRESSURE
36 TXD M-L
TRANSDUCER
37 RXD M-L SET
A-09131_AC
38 COMMON L-M J3
1
2
3
39 D M-L RUN +5VDC

1
RAR 0-100PSI / 0-4.5VDC 2
3
PCB3 LOGIC PCB
5 4 3 2

CUTMASTER A60
CM82 / A60 ONLY

TS1
1TORCH
L1
PIP SWITCH
J11
1
2
SEC1 SEC2 CHOKE1
D
+12VDC
TORCH SWITCH
TEMP
/OVERTEMP
CIRCUIT ATC CONNECTOR
J1
1 1 AUTOMATION
2 2 TORCH SOLENOID
3 3
4 4
NTC 5 5
6 6
7 7
8 8
-V OUT 1
-
E64
ELECTRODE1
D3
+
TIP1 E35
Q5
PILOT IGBT
WORK1
WORK
J9
78 C
/PIP 1
79
2 80
/START 3
81
4
24VAC RETURN 82
5
6 83
24VAC SUPPLY 7
CNC INTERFACE STANDARD ON A40 & A60 UNITS

CNC INTERFACE OPTIONAL ON CM52 & CM82 UNITS
J2
J10 P10 14
1 1
13
12
} OK TO MOVE
(5A @250VAC / 30VDC) J2 PINOUT
OK-TO-MOVE 2 2 11
3 3 10 3 1
4 4 9
5 5 8 7 4
+12VDC
6 6 7 11 8
7 7 6 14 12
8 8 5
4
3
} /START / STOP
(Sink 50mA @12VDC)
2
1
B
+12VDC +12VDC
/FAN /FAN * * To configure DIVIDED ARC VOLTS signal output
1
2
3
J7 To -V OUT 1
1
2
1
2
J8 J3
on PCB1
E1 J2
1
2
P10 J1 3
+12VDC
4 } /START / STOP
1 1 5 (-)
+ FAN - + FAN - 2 2 6 } (+) *DIVIDED ARC VOLTS
3 3 K1 7 (-)
MOT1 MOT2
4
5
4
5
8
9
}(+) (W/ARC VOLTS
100K IN SERIES (2))
6 6 10
7 7 11
8 8 12
K1 13 } OK-TO-MOVE
14
AUTOMATION
PCB4 INTERFACE PCB
A-09131_AC A
Rev Revisions By Date PCB No:

VICTOR TECHNOLOGIES
AA INTRO ECO B534 RWH 07/23/07 16052 Swingley Ridge Road Assy No:
AB ECO B890 MNC 04/23/08 Suite 300 Scale Supersedes
St Louis, MO 63017 USA
AC ECO B855 MNC 05/09/08
Date:
AD ECO B1159 MNC 10/03/08 Information Proprietary to THERMAL DYNAMICS CORPORATION.
Thursday, March 27, 2008
AE ECO B1357 RWH 03/31/09 Not For Release, Reproduction, or Distribution without Written Consent.
Drawn: References
NOTE: UNLESS OTHERWISE SPECIFIED - RWH
1. RESISTOR VALUES ARE EXPRESSED IN OHMS, 1/4W 5%.
2. CAPACITOR VALUES ARE EXPRESSED IN MICROFARADS (uF). Chk: App: Sheet
1 of 1
TITLE: SCHEMATIC, Size DWG No:
Last Modified: Monday, March 30, 2009 13:16:29
CUTMASTER 52/82/A40/A60 230/460V C 42X1298
1

CUTMASTER A60
APPENDIX 6: SYSTEM SCHEMATIC, 400V/600V UNITS
5 4
PRI 2 PRI 1 PRI 4 PRI 3

D
BIAS B A D C
SUPPLY
J1 MTH1 MTH2
SW1
1 3 +12VDC
1
2
3 Q1
4
2 4 5
K1
*CHOKE RESISTORS
INRUSH
EMI + C1-C4*
/INRUSH
* CEONLY
UNITS D1
MTH3
*FILTER
EMI
W1
MTH4
AC1
7
L1 1 1
L1 T1
AC2
8
L2 2 2
L2 T2
AC3
9
L3 3 3
L3 T3
7A
GND 4 4 L4 T4 MTH6 MTH8
Q2
C
380/400/415V
OR 600V
3 PH AC INPUT
PRIMARY POWER CONNECTIONS: + C5-C8*
USE L1, L2, L3 & GND
MTH7 MTH5
PCB2
INPUT CAPACITOR PCB
24VAC
5 *CM52/12mm/20mm/A40
J6
C3 & C5 may not be installed
TEST POINTS
W1 1
2 24 VAC RETURN
GND1 COMMON
GND2 COMMON
GND3 COMMON
6 +12V1 +12 VDC SUPPLY
48V1 +48 VDC SUPPLY
I_DMD_1 CURRENT DEMAND
J4 D59 PCR TIP_SEN TIP DRAG SENSE
1 3.3VDC
2 TXD
SERIAL PORT RXD
3
4 D78 CSR +12VDC
B 5 D
PCB1 MAIN PCB ASSY

/SOLENOID
J5
1
2
3
J2
40 CIRCUIT
RIBBON CABLE
J1
40 PIN RIBBON CABLE SIGNALS

SOL1
1 -V_OUT_SIGNAL M-L
2 /TIP_VOLTS M-L ERROR IND FAULT MAX
3 /TIP_SENSE M-L AC
4 /460V_IN L-M MAX OVER PRESSURE
5 /230V_IN L-M 90 INTERNAL ERROR
6 CUR_SET L-M 85 SHORTED TORCH 90
7 /RAR (RAPID AUTO RESTART) L-M OVERTEMP 80 CONSUMABLES MISSING
8 /INRUSH L-M 75 START ERROR
9 /W1_ON L-M 70 PARTS IN PLACE
10 /SHDN L-M 65 INPUT POWER 85
11 /TORCH_SOLENOID L-M GAS MIN UNDER PRESSURE
12 /SOLENOID_ON L-M
13 /OK_TO_MOVE L-M
14 /FAN_ON L-M TEST POINTS 80
DC
15 /LATCH_ACTIVE L-M
TP1 GND
16 /TORCH_SWITCH M-L
TP2 +12 VDC
17 /PIP M-L
TP3 +5 VDC 75 GAS CONTROL
18 AC_ON M-L ERROR TP4 3.3 VDC
19 CSR M-L
TP5 0.v - 5.0 VDC / 0-100PSI
20 /TORCH_SOLENOID_DETECT M-L REGULATOR
TP6 1.8 VDC SOLENOID
21 /OVERTEMP M-L 70 ATC
TP7 POT. DEMAND VALVE
A
22 V_IN M-L
23 +12VDC M-L
24 +12VDC M-L
25 COMMON M-L Current Control 65 FILTER
26 COMMON M-L +12VDC AIR
29 MAIN_PCB_ID M-L INLET
34 460_IN M-L
35 +3.3VDC L-M D1 MIN
LATCH PRESSURE
36 TXD M-L
TRANSDUCER
37 RXD M-L SET
A-09133_AD
38 COMMON L-M J3
1
2
3
39 D M-L RUN +5VDC

1
RAR 0-100PSI / 0-4.5VDC 2
3
PCB3 LOGIC PCB
5 4

CUTMASTER A60
3 2 1
TS1
T1
1TORCH
L1
PIP SWITCH
J11
1
2
SEC1 SEC2 CHOKE1
D
+12VDC
TORCH SWITCH
TEMP
/OVERTEMP
CIRCUIT ATC CONNECTOR
J1
1 1 AUTOMATION
2 2 TORCH SOLENOID
3 3
4 4
NTC 5 5
6 6
7 7
8 8
-V OUT 1
-
E64
ELECTRODE1
D3
+
TIP1 E35
Q5
PILOT IGBT
WORK1
WORK
J9
78 C
/PIP 1
79
2 80
/START 3
81
4
24VAC RETURN 82
5
6 83
24VAC SUPPLY 7
CNC INTERFACE STANDARD ON A40 & A60 UNITS

CNC INTERFACE OPTIONAL ON CM52 & CM82 UNITS
J2
J10 P10 14
1 1
13
12
} OK TO MOVE
(5A @250VAC / 30VDC) J2 PINOUT
OK-TO-MOVE 2 2 11
3 3 10 3 1
4 4 9
5 5 8 7 4
+12VDC
6 6 7 11 8
7 7 6 14 12
8 8 5
4
3
} /START / STOP
(Sink 50mA @12VDC)
2
1
B
+12VDC +12VDC
/FAN /FAN * * To configure DIVIDED ARC VOLTS signal output
1
2
3
J7 To -V OUT 1
1
2
1
2
J8 J3
on PCB1
E1 J2
1
2
P10 J1 3
+12VDC
4
} /START / STOP
1 1 5 (-)
+ FAN - + FAN - 2 2 6 } (+) *DIVIDED ARC VOLTS
3 3 K1 7 (-)
MOT1 MOT2
4
5
4
5
8
9
} (+) (W/ARC VOLTS
100K IN SERIES (2))
6 6 10
7 7 11
8 8 12
K1 13 } OK-TO-MOVE
14
AUTOMATION
PCB4 INTERFACE PCB
A-09133_AD A
Rev Revisions By Date PCB No:

VICTOR TECHNOLOGIES
AA INTRO ECO B1357 RWH 03/31/09 16052 Swingley Ridre Road, Assy No:
AB ECO B1399 RWH 05/05/09 Suite 300 Scale Supersedes
St Louis, MO 63017 USA
Date:
Information Proprietary to THERMAL DYNAMICS CORPORATION.
Thursday, March 27, 2008
Not For Release, Reproduction, or Distribution without Written Consent.
Drawn: References
NOTE: UNLESS OTHERWISE SPECIFIED - RWH
1. RESISTOR VALUES ARE EXPRESSED IN OHMS, 1/4W 5%.
2. CAPACITOR VALUES ARE EXPRESSED IN MICROFARADS (uF). Chk: App: Sheet
1 of 1
TITLE: SCHEMATIC, Size DWG No:
Last Modified: Wednesday, May 06, 2009 13:16:29
CM52/82/12mm/20mm/25mm/A40/A60 380/400/415/600V C 42X1329
3 2 1

CUTMASTER A60
APPENDIX 7: RAW ARC VOLTAGE
If raw arc voltage is necessary for the torch height control, the customer must supply an 18 AWG (1.0 mm2), single pair, unshielded
cable rated for 300V or greater. All work must be performed following applicable local and national codes.
1. Disconnect the power from the power supply.

2. Remove the screws that attach the power supply cover to the chassis. Remove the cover.
3. Route the cable through the customer supplied strain relief at the rear of the power supply.
Cut out for cable
Art # A-10286
4. On the main board use insulated type 1/4-inch ring lug terminal ends to connect to –Vout1 (- polarity) and WORK 1 (+ polar-
ity).
! WARNING
The raw arc voltage can exceed 350VDC !!!!
WORK 1
-V OUT 1
WORK 1
-V OUT 1
J10
Art # A-10287

CUTMASTER A60
Art # A-10288
-V out (-) Polarity Work1 (+) Polarity
5. Tighten the strain relief.

6. Replace the cover.
7. Connect the cable to negative and positive of Torch Height Control .

CUTMASTER A60
APPENDIX 8: PUBLICATION HISTORY
Cover Date Rev. Change(s)
Dec. 20, 2007 AA Manual released.

Apr. 15, 2008 AB Per ECOB752 updated firmware changes to pgs. 4-1 and 5-5. Per ECOB845 corrected drag cutting
statement to ¼” pg. 4T-5. Per ECOB803 releasing 400 – 460V systems.
May 7, 2008 AC Per ECOB890 updated system schematic. Per ECOB880 updated section 2 spec chart and input wir
ing chart for CSA approval.
May 16, 2008 AD Added information to section 6 about regulator - logic PCB kit upgrade for older systems per
ECOB908.
July 17, 2008 AE Updated input power and cable charts in section 2. Updated 208/460V System schematic. Added
400V system schematic in the Appendix per ECOB933.
Jan 27, 2009 AF Corrected art in section 3 to show all information per ECOB1248.
Apr. 14, 2009 AG Updated system specs and input wiring specs in section 2. Updated with 600v system information
per ECOB1346.
May 29, 2009 AH Updated 400V/600V schematic in appendix per ECOB1399 and updated 230/460V schematic per
ECOB1357.
Oct. 20, 2009 AI Updated electrode part number per ECOB1494 by changing 9-8215 to 9-8232.
Jan. 7, 2010 AJ Updated torch consumables art section 4T and 6. Updated automation interface and harness de
scriptions and part numbers per ECOB1282.
Feb. 25, 2010 AK Updated CNC cable part numbers in section 6 per ECOB1637.
Feb. 8, 2011 AL Per ECOB1859 corrected Schematics with art number A-09131 and A-09133 to show proper ARC
Volts for Automation Interface PCB.
Mar. 14, 2011 AM Updated power cord part number in section 6 per ECOB1234.
June 22, 2011 AN Added Appendix 7: Raw Arc Voltage
Mar. 20, 2012 AO Updated ART A-08066 and changed COO text, per ECOB2149.
Aug. 20, 2012 AP Added Opening the Contactor Cover text per ECOB2122. Inserted Victor Technologies branding text.
Dec. 7, 2012 AQ Added Heavy Duty Starter Cartridge 80 ×144 (9-8277) to automated 1Torch per ECOB2305
Dec. 17, 2012 AR Changed logo on Front Cover and Inside Front Cover from "Thermal Dynamics" to "Victor Thermal
Dynamics", modified Prop 65 Text Section 1, added information regarding Automation Interface Kit
to 3T.02 pg. 3T-1, deleted information regarding Automation Interface Kit from 6.05 pg. 6-2, added
SL100SV Automation Torch and Leads Packages pg. 6-4, and deleted items 10 & 11 pg. 6-9 per
ECO-B2342.
Nov. 26, 2013 AS Updated Declaration of Conformity. Made the following rebranding changes: updated cover to
show new Victor Thermal Dynamics trade dress, updated thank you text, changed headers and
footers, updated rear cover.
Feb. 2, 2014 AT More rebranding and unknown. Unknown ECO
Oct. 24, 2014 AU Updated page 2 of section 3T with jumper information and warning per ECOB2673

THE AMERICAS
Denton, TX USA
U.S. Customer Care
Ph 1-800-426-1888 (tollfree)
Fax: 1-800-535-0557 (tollfree)
International Customer Care
Ph 1-940-381-1212
Fax: 1-940-483-8178
Miami, FL USA
Sales Office, Latin America
Ph 1-954-727-8371
Fax: 1-954-727-8376
Oakville, Ontario, Canada

Canada Customer Care
Ph 1-905-827-4515
Fax: 1-800-588-1714 (tollfree)
EUROPE
Chorley, United Kingdom
Customer Care
Ph +44 1257-261755
Fax: +44 1257-224800
Milan, Italy
Customer Care
Ph +39 0236546801
Fax: +39 0236546840
ASIA/PACIFIC
Cikarang, Indonesia
Customer Care
Ph 6221-8990-6095
Fax: 6221-8990-6096
Rawang, Malaysia
Customer Care
Ph +603 6092-2988
Fax: +603 6092-1085
Melbourne, Australia
Australia Customer Care
Ph 1300-654-674 (tollfree)
Ph 61-3-9474-7400
Fax: 61-3-9474-7391
International
Ph 61-3-9474-7508
Fax: 61-3-9474-7488
Shanghai, China
Sales Office
Ph +86 21-64072626
Fax: +86 21-64483032
Singapore
Sales Office
Ph +65 6832-8066
Fax: +65 6763-5812
INNOVATION TO SHAPE THE WORLD™
U.S. Customer Care: 800-426-1888 / FAX 800-535-0557

Canada Customer Care: 905-827-4515 / FAX 800-588-1714
International Customer Care: 940-381-1212 / FAX 940-483-8178
© 2012 Victor Technologies International, Inc. www.victortechnologies.com Printed in Mexico

Cutmaster A60: Operating Manual

Uploaded by

Copyright:

Available Formats

Cutmaster A60: Operating Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cutmaster A60: Operating Manual

Uploaded by

Copyright:

Available Formats

60 208-

230V 400V 460V 600V

Revision: AU Issue Date: October 24, 2014 Manual No.: 0-4981

YOU ARE IN GOOD COMPANY!

Plasma Cutting Power Supply

Copyright 2008, 2009, 2010, 2011, 2012, 2013, 2014by

All rights reserved.

Original Publication Date: January 7, 2008

Power Supply Serial #:_________________________________________

Torch Serial #:_______________________________________________

SECTION 5 SYSTEM: SERVICE............................................................................ 5-1

APPENDIX 2: DATA TAG INFORMATION.................................................................. A-2

APPENDIX 3: TORCH PIN - OUT DIAGRAMS............................................................ A-3

APPENDIX 4: TORCH CONNECTION DIAGRAMS........................................................ A-4

APPENDIX 5: SYSTEM SCHEMATIC, 208/460V UNITS................................................. A-6

APPENDIX 6: SYSTEM SCHEMATIC, 400V/600V UNITS............................................... A-8

APPENDIX 7: RAW ARC VOLTAGE .......................................................................A-10

APPENDIX 8: PUBLICATION HISTORY...................................................................A-12

! WARNING ELECTRIC SHOCK

Manual 0-4981 GENERAL INFORMATION 1-1

ATTENTION • Les sortes de gaz et de fumée provenant de l’arc de plasma dépen-

Coupant à l’arc au jet de plasma produit de l’énergie

1.06 Documents De Reference

1-4 INFORMATIONS GÉNÉRALES Manuel 0-4981

Manuel 0-4981 INFORMATIONS GÉNÉRALES 1-5

Manufacturer: Victor Technologies International Inc.

Date: March 18, 2014 V.P. Europe and General Manager

1-6 GENERAL INFORMATION Manual 0-4981

Manual 0-4981 GENERAL INFORMATION 1-7

Power Supply Components Torch and Leads

This warranty does not apply to:

1-8 GENERAL INFORMATION Manual 0-4981

Additional copies of this manual may be purchased by contact-

Manual 0-4981 INTRODUCTION 2-1

CutMaster A60 Power Supply Specifications

Power Supply Dimensions & Weight Ventilation Clearance Requirements

2-2 INTRODUCTION Manual 0-4981

CutMaster A60 Power Supply Input Cable Wiring Requirements

Manual 0-4981 INTRODUCTION 2-3

Gas Inlet Port

Input Power Cord Art # A-08318

2-4 INTRODUCTION Manual 0-4981

2T.02 General Description

A. Torch Configurations D. Parts - In - Place (PIP)

Manual 0-4981 INTRODUCTION 2T-1

Automated, Manual and Machine Torch Gas

Maximum Input Pressure 125 psi / 8.6 bar A

2T-2 INTRODUCTION Manual 0-4981

The single gas used is internally split into plasma and

D. Main Cutting Arc

E. Parts - In - Place (PIP) To ATC PIP Switch Shield Cup

The torch includes a 'Parts - In - Place' (PIP) circuit. When

Torch Switch Torch Trigger

Parts - In - Place Circuit Diagram for Hand Torch

Manual 0-4981 INTRODUCTION 2T-3

This Page Intentionally Blank

2T-4 INTRODUCTION Manual 0-4981

INSTALLATION the four keyway holes in the mounting

3.02 Lifting Options 3.04 Opening the Contactor Cover