CQI-12 Coating System 3-29-16

CQI-12v2
Special Process: Coating System Assessment
AIAG Copyright and Trademark Notice:
© 2012 Automotive Industry Action Group, except that copyright is not claimed as to any part
of an original work prepared by a U.S. or state government officer or employee as part of the
person’s official duties.
Except as noted above, all rights are reserved by AIAG and no part of these materials may
be reproduced, reprinted, stored in a retrieval system, or transmitted, in any form or by any
means, electronic, photocopying, recording, or otherwise, without the prior written permission
of Automotive Industry Action Group. Copyright infringement is a violation of federal law
subject to criminal and civil penalties.
AIAG and Automotive Industry Action Group are registered service marks of the Automotive
Industry Action Group. Automotive Industry Action Group makes no claim to any trademark of
a third party. Trademarks of third parties included in these materials are the property of their
respective owners
© 2012 Automotive Industry Action Group
© 2012 Automotive Industry Action Group

ISBN#: 978-1-60534-245-0-90000
CQI-12v2
1
Dated: 2/2012
CQI-12
Version 2 Issued 2/2012
Special Process: Coating System Assessment 2nd Edition
Facility Name:
Address:
Phone Number: Type(s) of Coating Processes at this Facility:

Fax Number: Process Table A
Pretreatment, Aqueous
Number of Coating Employees at this Facility: Process Table B
Pretreatment, Mechanical
Captive Coater (Y/N): Process Table C
Commercial Coater (Y/N): Conversion Coating
Process Table D
Date of Assessment: Powder Coating
Process Table E
Date of Previous Assessment: Spray
Process Table F
Electrocoat
Process Table G
Dip/Spin
Process Table H
Autodeposition
Process Table I
Cure
Process Table J
Anodizing
Process Table K
Equipment
Process Table L
Part Inspection & Testing
Current Quality Certification(s):
Date of Re-assessment (if necessary):
Personnel Contacted:
Name: Title: Phone: Email:
Auditors/Assessors:
Name: Company: Phone: Email:
Number of "Not Satisfactory" Findings:
Number of "Needs Immediate Action" Findings:
Number of "Fail" Findings in the Job Audit(s):
Number of Process Table Items not meeting Minimum Requirements:
© 2012 AIAG (Automotive Industry Action Group)

CQI-12
Special Process: Coating System Assessment (General Facility Overview)
Assessment
Question Needs Immediate

Question Requirements and Guidance Objective Evidence N/A Satisfactory Not Satisfactory
Number Action
Section 1 - Management Responsibility and Quality Planning
To ensure readily available expertise, there shall be a

dedicated and qualified coating person on the site.
This individual shall be a full-time employee and the
position shall be reflected in the organization chart. A
Is there a dedicated and
job description shall exist identifying the qualifications
1.1 qualified coating person on-
for the position including chemical and coating
site?
knowledge. The qualifications shall include a
minimum of 5 years experience in coating operation or
a combination of a minimum of 5 years of formal
chemical education and coating experience.
The coater shall incorporate a documented advanced

quality planning procedure. A feasibility study shall be
performed and internally approved for each new part
or process. Similar parts can be grouped into part
families for this effort as defined by the coater. After
Does the coater perform
1.2 the part approval process is approved by the
advanced quality planning?
customer, no process changes are allowed unless
approved by the customer. The coater shall contact
the customer when clarification of process changes is
required. This clarification of process changes shall
be documented.

CQI-12
Assessment

Number Action
The coater shall incorporate the use of a documented

Failure Mode and Effects Analysis (FMEA) procedure
and ensure the FMEAs are updated to reflect current
part quality status. The FMEA shall be written for each
part or part family or they may be process-specific and
Are the coater's FMEA's up to written for each process. In any case, they shall
1.3 date and reflecting current address all process steps from part receipt to part
processing? shipment and all key coating process parameters as
defined by the coater. A cross-functional team shall be
used in the development of the FMEA. All special
characteristics, as defined by the coater and its
customers, shall be identified, defined, and addressed
in the FMEA.
The coater shall incorporate the use of a documented

Control Plan procedure and ensure the Control Plans
are updated to reflect current controls. The Control
Plans shall be written for each part or part family or
they may be process-specific and written for each
process. In any case, they shall address all process
steps from part receipt to part shipment and identify all
equipment used and all key coating process
parameters as defined by the coater. A cross-
Are finish process Control
functional team, including a production operator, shall
1.4 Plans up to date and reflecting
be used in the development of Control Plans, which
current processing?
shall be consistent with all associated documentation
such as work instructions, shop travelers, and FMEAs.
All special characteristics, as defined by the coater
and its customers, shall be identified, defined, and
addressed in the Control Plans. Sample sizes and
frequencies for evaluation of process and product
characteristics shall also be addressed consistent with
the minimum requirements listed in the Process
Tables.

CQI-12
Assessment

Number Action
To ensure all customer requirements are both

understood and satisfied, the coater shall have all
related coating and customer referenced standards
and specifications available for use and a method to
ensure that they are current. Such standards and
specifications include, but are not limited to, those
relevant documents published by SAE, AIAG, ASTM,
General Motors, Ford, and Chrysler. The coater shall
Are all coating related and
have a process to ensure the timely review,
referenced specifications
distribution, and implementation of all customer and
current and available? For
1.5 industry engineering standards and specifications and
example: SAE, AIAG, ASTM,
changes based on customer-required schedule. This
General Motors, Ford, and
process shall be executed as soon as possible and
Chrysler.
shall not exceed two weeks. The coater shall
document this process of review and implementation,
and it shall address how customer and industry
documents are obtained, how they are maintained
within the coater, how the current status is established,
and how the relevant information is cascaded to the
shop floor within the two-week period. The coater shall
identify who is responsible for performing these tasks.
The coater shall have written process specifications for

all active processes and identify all steps of the
process including relevant operating parameters.
Examples of operating parameters include process
temperatures, cycle times, load rates, rectifier settings,
Is there a written process
etc. Such parameters shall not only be defined, they
1.6 specification for all active
shall have operating tolerances as defined by the
processes?
coater in order to maintain process control. All active
processes should have a written process specification.
These process specifications may take the form of
work instructions, job card, computer-based recipes, or
other similar documents.

CQI-12
Assessment

Number Action
To demonstrate each process is capable of yielding

acceptable product, the coater shall perform product
capability studies for the initial validation of each
process, after relocation of any process equipment,
and after a major rebuild of any equipment. The coater
shall define what constitutes a major rebuild. Initial
product capability studies shall be conducted for all
coating processes per line as defined in scope of work
Has a valid product capability
and in accordance with customer requirements.
1.7 study been performed initially
Capability study techniques shall be appropriate for
and after process change?
the coating product characteristics, e.g., coating
thickness, corrosion resistance, etc.. Any specific
customer requirements shall be met. In the absence of
customer requirements, the coater shall establish
acceptable ranges for measures of capability. An
action plan shall exist to address the steps to be
followed in case capability indices fall outside
customer requirements or established ranges.
The analysis of products and processes over time can

yield vital information for defect prevention efforts.
The coater shall have a system to collect, analyze, and
Does the coater collect and react to product or process data over time. Methods of
analyze data over time, and analysis shall include ongoing trend or historical data
1.8 react to this data? Are records analysis of special product or process parameters.
available? The coater shall determine which parameters to
include in such analysis. All process control and
testing records must be retained for a minimum of one
calendar year after the year in which they were
created.
Are internal assessments

The coater shall conduct internal assessments on an
being completed on an annual
1.9 annual basis, at a minimum, using the AIAG CSA.
basis, at a minimum,
Concerns shall be addressed in a timely manner.
incorporating AIAG CSA?

CQI-12
Assessment

Number Action
The quality management system shall include a

documented process for reprocessing that shall
include authorization from a designated individual.
The reprocessing procedure shall describe product
characteristics for which reprocessing is allowed as
Is there a system in place to well as those characteristics for which reprocessing is
1.10 authorize reprocessing and is not permissible. All reprocessing activity shall require
it documented? a new processing control sheet issued by qualified
technical personnel denoting the necessary coating
modifications. Records shall clearly indicate when and
how any material has been reprocessed. The Quality
Manager or a designee shall authorize the release of
reprocessed product.
The quality management system shall include a

Does the Quality Department
process for documenting, reviewing, and addressing
review, address, and
1.11 customer concerns and any other concerns internal to
document customer and
the coater. A disciplined problem solving approach
internal concerns?
shall be used.
The coater shall define a process for continual

improvement for each coating process identified in the
Is there a continual
scope of the CSA. The process shall be designed to
improvement plan applicable
1.12 bring about continual improvement in quality and
to each process defined in the
productivity. Identified actions shall be prioritized and
scope of the assessment?
shall include timing (estimated completion dates). The
coater shall show evidence of program effectiveness.
Does the Quality Manager or

The Quality Manager or designee is responsible for
designee authorize the
1.13 authorizing and documenting appropriate personnel to
disposition of material from
disposition quarantine material.
quarantine status?

CQI-12
Assessment

Number Action
There shall be procedures or work instructions

available to coating personnel covering the coating
process. These procedures or work instructions shall
Are there procedures or work
include methods of addressing potential emergencies
instructions available to
1.14 (such as power failure), equipment start-up, equipment
coating personnel that define
shut-down, product segregation (See 2.8), product
the coating process?
inspection, and general operating procedures. These
procedures or work instructions shall be accessible to
shop floor personnel.
The coater shall provide employee training for all

coating operations. All employees, including backup
and temporary employees, shall be trained.
Documented evidence shall be maintained showing
Is management providing
1.15 the employees trained and the evidence shall include
employee training for coating?
an assessment of the effectiveness of the training.
Management shall define the qualification
requirements for each function, and ongoing or follow-
up training shall also be addressed.
The coater shall maintain a responsibility matrix

Is there a responsibility matrix identifying all key management and supervisory
to ensure that all key functions and the qualified personnel who may perform
1.16 management and supervisory such functions. It shall identify both primary and
functions are performed by secondary (backup) personnel for the key functions
qualified personnel? (as defined by the coater). This matrix shall be readily
available to management at all times.

CQI-12
Assessment

Number Action
The coater shall have a documented preventive

maintenance program for key process equipment (as
identified by the coater). The program shall be a
closed-loop process that tracks maintenance efforts
Is there a preventive from request to completion to assessment of
maintenance program? Is effectiveness. Equipment operators shall have the
maintenance data being opportunity to report problems, and problems shall
1.17
utilized to form a predictive also be handled in a closed-loop manner. Company
maintenance program? data, e.g., downtime, quality rejects, first time-through
capability, recurring maintenance work orders, and
operator-reported problems, shall be used to improve
the preventive maintenance program. Maintenance
data shall be collected and analyzed as part of a
predictive maintenance program.
Has the coater developed a

The coater shall develop and maintain a critical spare
critical spare parts list, and are
1.18 parts list and shall ensure the availability of such parts
the parts available to minimize
to minimize production disruptions.
production disruptions?

CQI-12
Assessment

Number Action
Section 2 - Floor and Material Handling Responsibility

Does the facility ensure that
Documented processes and evidence of compliance
the data entered in the
shall exist, e.g., shop travelers, work orders, etc. The
2.1 receiving system matches the
facility shall have a detailed process in place to resolve
information on the customer's
receiving discrepancies.
shipping documents?
Procedures for part and container identification help to

avoid incorrect processing or mixing of lots.
Appropriate location and staging within the facility also
help to ensure that orders are not shipped until all
Is product clearly identified
required operations are performed. Customer product
2.2 and staged throughout the
shall be clearly identified and staged throughout the
coating process?
coating process. Non-coated, in-process, and finished
product shall be properly segregated and identified. All
material shall be staged in a dedicated and clearly
defined area.
Out-going lot(s) shall be traceable to the incoming

Is lot traceability and integrity lot(s). The discipline of precisely identifying lots and
2.3 maintained throughout all linking all pertinent information to them enhances the
processes? ability to do root cause analysis and continual
improvement.
The control of suspect or non-conforming product is

necessary to prevent inadvertent shipment or
contamination of other lots. Procedures shall be
Are procedures adequate to
adequate to prevent movement of non-conforming
prevent movement of non-
2.4 product into the production system. Procedures shall
conforming product into the
exist addressing proper disposition, product
production system?
identification and tracking of material flow in and out of
hold area. Non-conforming hold area shall be clearly
designated to maintain segregation of such material.

CQI-12
Assessment

Number Action
Is there a system to identify

trap points in the entire The coater shall have documented procedures to
process to reduce risk of identify and monitor trap points for each
2.5
mixed parts (inappropriate, process/equipment. Monitoring of potential trap points
unfinished or improperly shall occur for every part changeover.
coated parts)?
Containers handling customer product shall be free of

inappropriate material. After emptying and before re-
using containers, containers shall be inspected to
Are containers free of ensure that all parts and inappropriate material have
2.6
inappropriate material? been removed. The source of inappropriate material
shall be identified and addressed. This is to ensure
that no nonconforming coated parts or inappropriate
material contaminate the finished lot.
Loading parameters shall be specified, documented

and controlled. Examples include parts per rack and
Is part loading specified,
2.7 load size.
documented and controlled?
Refer to Process Tables for frequency of checks.
Unplanned or emergency downtime greatly raises the

risk of improper processing. Operators shall be trained
in material handling, containment action, and product
Are operators trained in segregation in the event of an equipment emergency
material handling, containment including power failure. Training shall be documented.
action and product Work instructions specifically addressing potential
2.8
segregation in the event of an types of equipment emergencies and failures shall be
equipment emergency accessible to and understood by equipment operators.
including power failure? These instructions shall address containment/reaction
plans related to all elements of the process. Evidence
shall exist showing disposition and traceability of
affected product.

CQI-12
Assessment

Number Action
Is the handling, storage and The coater's loading/unloading systems, in-process

2.9 packaging adequate to handling and shipping process shall be assessed for
preserve product quality? risk of part damage or other quality concerns.

CQI-12
Assessment

Number Action
Plant cleanliness, housekeeping, environmental, and

working conditions shall be conducive to controlling
Are plant cleanliness,
and improving quality. The coater should evaluate
housekeeping, environmental
such conditions and their effect on quality. A
2.10 and working conditions
housekeeping policy shall be clearly defined and
conducive to control and
executed. The facility shall be reviewed for the
improved quality?
following items: loose parts on floor; spillage around
tanks; overall plant lighting; fumes etc.
Process control parameters shall be monitored per

Are process control frequencies specified in Process Tables. Computer
parameters monitored per monitoring equipment with alarms and alarm logs
2.11
frequencies specified in satisfy the verification requirement. A designated floor
Process Tables? person shall verify the process parameters, e.g., by
initialing a strip chart or data log.
There are documented reaction plans to both out of

Are out of control/specification
control and out of tolerance process parameters.
2.12 parameters reviewed and
There is documented evidence that reaction plans are
reacted to?
followed.
Are In-Process / Final Test In-Process / Final Test Frequencies shall be

2.13 Frequencies performed as performed as specified in Process Tables. Refer to
specified in Process Tables? Process Tables.
Test equipment shall be verified/calibrated per

applicable customer specific standard or per an
applicable consensus standard, e.g., ASTM, SAE,
Is product test equipment
2.14 ISO, NIST, etc. Verification/calibration results shall be
verified?
internally reviewed, approved and documented.
Refer to Process Tables for frequency of checks.

CQI-12
Assessment

Number Action
Lighting in the inspection area must be sufficient to

allow the evaluation of all part surfaces. The lighting
Is lighting of inspection area
2.15 shall be arranged to preclude spot lighting, glare or
adequate?
shadows. There can be no moving or distracting
reflections on the surfaces to be evaluated.
Identify operating parameters including:

- number of rinse tanks between process stages,
- tank type (single rinse, counter flowing, stationary
rinse, spray rinse)
Are the water rinse Control
- flow rate,
2.16 Plans up to date and reflect
- water requirements (city or deionized water, reverse
best case practices?
osmosis),
- filtration (if applicable)
- control methods
- temperature (if applicable)
Aware of water quality and it's impact on each specific

2.17 Is the water quality adequate? process. Purified water is used where necessary, or
where specified.

CQI-12
Section 3 - Job Audit - Finished Product Review
Job Identity:
Customer:
Shop Order Number:
Part Number:
Part Description:
Coating Requirements:
Related Customer or Internal Job (Shop) Order or Reference Actual Condition Pass / Fail
Question # Job Audit Question
CSA Question # Requirement Documentation Requirement (Objective Evidence) / N/A
1.1
Is contract review and advanced quality 1.2
3.1 planning, FMEA, Control Plans, etc., 1.3 N/A
performed by qualified individuals? 1.4
1.6
Does the coater have the proper customer

3.2 1.5 N/A
specifications for the part?
Is a shop traveler created to meet 1.6

3.3
customer requirements? 2.1
Is material identification (part numbers, lot

2.2
numbers, contract numbers, etc.)
3.4 2.3
maintained throughout the coating
2.4
process?
Is there documented evidence of

3.5 2.1
Receiving Inspection?
1.6
Are the Loading / Racking requirements
3.6 2.7
identified?
2.9

CQI-12
Job Identity:
Customer:
Shop Order Number:
Part Number:
Part Description:
Is the proper procedure or process 1.5

specification used? Refer to Process 1.6
3.7 Tables for specific parameters. List 2.1
parameters that were verified in this audit 2.11
in the spaces provided below. 2.13

CQI-12
Job Identity:
Customer:
Shop Order Number:
Part Number:
Part Description:
Each part may have one or more requirements determined by the coating specification.
What are the product inspection 1.5
3.8 Parts must meet each requirement. List each requirement below and validate.
requirements? 2.13 2.14
(Listed below are some examples)
3.8.1 Requirement: Coating Thickness
Test Method:
Test frequency or quantity:
Selection of samples:
Specification:
Requirement: Corrosion Resistance (if
3.8.2
applicable)
Test Method(s):
Specification:
Requirement: Hydrogen Embrittlement

3.8.3
Relief (if applicable)
Test Method:

CQI-12
Job Identity:
Customer:
Shop Order Number:
Part Number:
Part Description:

Specification:
3.8.4 Requirement: Adhesion
Test Method(s):
Specification:
3.8.5 Requirement: Cure
Test Method:
Specification:
Requirement: Torque Tension
3.8.6
(if applicable)
Test Method:

CQI-12
Job Identity:
Customer:
Shop Order Number:
Part Number:
Part Description:

CQI-12
Job Identity:
Customer:
Shop Order Number:
Part Number:
Part Description:
Specification:
3.8.7 Requirement: Appearance (Decorative)
Test Method:
Specification:
Requirement: Dimensional
3.8.8
(if applicable)
Test Method:
Specification:
Requirement: Color and Gloss
3.8.9
(Decorative)
Test Method:
Specification:

CQI-12
Job Identity:
Customer:
Shop Order Number:
Part Number:
Part Description:
3.8.10 Requirement: Customer Specific

Test Method(s):
Specification:
Operator or Inspector Responsibilities
1.4
1.6
Were appropriate process steps signed
3.9 2.2
off?
2.3
2.11
Were all inspection steps, as documented 1.2

3.10
in the Control Plan performed? 1.4

CQI-12
Job Identity:
Customer:
Shop Order Number:
Part Number:
Part Description:
1.2
Were steps/operations performed that
3.11 1.4
were not documented in the Control Plan?
1.6
1.2
1.4
If additional steps were performed, were
3.12 1.6
they authorized?
1.10
1.16
Does the governing specification allow 1.5

3.13
reprocessing or rework? 1.10
If the order was certified, did the

2.11
3.14 certification accurately reflect the process
2.13
performed?
Was the certification signed by an

3.15 1.16
authorized individual?
Are the parts and containers free of

3.16 2.6
inappropriate objects or contamination?

CQI-12
Job Identity:
Customer:
Shop Order Number:
Part Number:
Part Description:
Packaging Requirements
2.6
3.17 Are packaging requirements identified? 2.7
2.9
Are parts packaged to minimize mixed 2.6

3.18 parts (for example, parts packed over 2.7
height of container)? 2.9
Shipping Requirements
2.3
3.19 Were the parts properly identified?
2.9
2.3
3.20 Were the containers properly labeled?
2.9

CQI-12
PROCESS TABLE A - Pretreatment (Aqueous)
All requirements given below are subordinate to customer specific requirements.
The customer may have additional requirements, e.g., inspection testing, greater frequencies, etc. When performing the job audit, the auditor shall verify coater is conforming to customer requirements.
*If minimum requirements are not met, provide supporting records to justify actual conditions.
Related
Item # CSA Category/Process Steps Type of Control Monitoring Frequency Observation/Comments
Question #
Minimum
Actual Condition Minimum Requirement Actual Condition (Pass / Fail / N/A)
Requirement
1.0 AQUEOUS CLEANING PROCESS (Alkaline or Acid)
There shall be an incoming part assessment procedure

A1.1 1.4 Per Control Plan Once per lot and per part change
with criteria.
Automatic Line: Confirm set-up at the start

of production and every process change.
1.4 Manually verify every 3 months or after
1.6 programming change or equipment
A1.2 Time Automatic/Manual
2.11 maintenance.
2.12
Manual Line: Continuously monitor time in
each stage of process.

CQI-12
Related
Question #
Minimum
Requirement
2.0 Cleaning / Descaling Solution
1.4
Pressure for spray rinse.
A2.1 2.11 Automatic/Manual Once every 8 hours
Agitation for immersion tanks.
2.12
1.4
Continuous monitoring by controller.
A2.2 2.11 Temperature Automatic
Manually verify daily.
2.12
Chemical Concentration (Alkaline Cleaner) (If used)

Per chemical supplier recommendation such as:
1.4 - free alkalinity
For continuous operations, once per day.
1.6 - total alkalinity
A2.3 Automatic/Manual Otherwise, prior to start of each production
2.11 - pH
cycle.
2.12 - conductivity
- percentage of cleaner (weight/volume or
volume/volume)
1.4 Chemical Concentration (Acid Cleaner) (If used) For continuous operations, once per day.
1.6 Per chemical supplier recommendation such as: Otherwise, prior to start of each production
A2.4 Automatic/Manual
2.11 - free acidity or concentration day. (once per day for concentration, once
2.12 - metal contamination per month for contamination).
Impurity Content
1.4
Per chemical supplier recommendation such as:
A2.5 2.11 Manual Once per week*
- acid split (oil contamination)
2.12
- alkalinity ratio
There is a tank maintenance schedule for cleaning

A2.6 2.11 Manual Per preventative maintenance program
baths.

CQI-12
Related
Question #
Minimum
Requirement
3.0 Rinse(s)
1.4
A3.1 2.11 Automatic/Manual Once every 8 hours
Agitation or flow for immersion tanks.
2.12
1.4
A3.2 2.11 Temperature (if controlled) Automatic
Manually verify once per day.
2.12
Cleanliness of last cleaner rinse

1.4
- alkalinity/pH/conductivity
A3.3 2.11 Manual Once per day
- visual inspection for oil or suspended contaminants
2.12
- overflow
A3.4 2.11 There is a dump schedule for rinses. Manual Per preventative maintenance schedule.
There is a visual inspection (e.g. water break) after

1.4
A3.5 each post cleaning rinse bath (not applicable for closed Manual Once every 8 hours
2.11
barrel systems).
1.4
A3.6 Corrosion inhibitor concentration is checked. (If used) Automatic/Manual Once every 8 hours
2.11

CQI-12
Related
Question #
Minimum
Requirement
4.0 Acid Pickling
1.4
A4.1 2.11 Concentration Manual Once every 8 hours
2.13
1.4
A4.2 2.11 Concentration of Fe, per coating supplier. Manual Once per day
2.12
1.4
A4.3 2.11 Inhibitor (if used) Manual N/A
2.12
1.4
A4.4 2.11 Solution Level Manual Once every 8 hours
2.12
A4.5 Rinse - See Section 3.0.
5.0 Aluminum Etching
1.4
2.12
1.4
A5.2 2.11 Concentrations of Al, per coating supplier. Manual Once per day
2.12

CQI-12
Related
Question #
Minimum
Requirement
6.0 Aluminum Deoxidizing
1.4
2.12
1.4
A6.2 2.11 Concentrations of Al, per coating supplier. Manual Once per day
2.12
7.0 Sealing Rinse (if applicable)
1.4
A7.1 2.11 Temperature (if applicable) Automatic Manually measure once every 8 hours
2.13
1.4
2.12
1.4
A7.3 2.11 Solution Level Manual Once every 8 hours
2.12

CQI-12
PROCESS TABLE B - Pretreatment (Mechanical)
Related
Question #
Minimum Requirement Actual Condition Minimum Requirement Actual Condition (Pass / Fail / N/A)
1.0 ABRASIVE BLAST PROCESS
There shall be an incoming part assessment procedure

B1.1 1.4 with criteria. (Parts have been pre-cleaned and are free Manual Per load
of oil and grease contaminations).
The following checks shall be performed during

B1.2 2.11
production:
B1.3 Load Weight Manual / Automatic Per load
B1.4 Blasting Media Size / type Manual Per load
1.4
Dwell time is clearly defined.
1.6
B1.5 If additional blasting is required, management approval Manual / Automatic Per load
2.11
is needed.
2.12
Blasting force is set and maintained within control limits

B1.6 Manual / Automatic Per load
(Amperage Draw).

CQI-12
PROCESS TABLE B - Pretreatment (Mechanical)
Related
Question #
1.4
1.6
B1.7 Abrasive media level Manual Once every 8 hours
2.11
2.12
1.4
B1.8 2.11 Dust collector efficiency/air flow Manual Once every 4 hours
2.12
1.4 Blasting media size / life:

B1.9 2.11 Media size is being checked on a regular schedule to Manual / Automatic Once per week
2.12 determine effective cleaning and life for product mix.
Surface cleanliness is checked after process. Surface

1.4
B1.10 cleanliness check must be conducted using a chemical Manual Once every 4 hours
2.11
("Copper Sulfate") or other qualitative method.
1.4
Surface profile is checked after process
B1.11 2.11 Manual Per load
(if applicable).
2.13

CQI-12
PROCESS TABLE C - Conversion Coatings (Phosphate, Non-phosphate, Chromate, Non-chrome)
Related
Question #
1.0 Conversion Coating
This audit requires the completion of either

C1.1 1.4 n/a n/a
Table A and/or B.
If the pretreatment and phosphate is not a continuous

process, there shall be a part cleanliness check Every start of production cycle and change
C1.2 Manual
immediately before phosphate. Acceptance criteria of lot number and each container.
must be defined.
Confirm set-up at the start of production

1.4
and every process change.
1.6
C1.3 Time Automatic Manually verify every 3 months or after
2.11
programming change or equipment
2.12
maintenance.
2.0 Conditioner (If Applicable)

1.4
C2.1 2.11 Pressure/Agitation Automatic Once every 8 hours
2.12
1.4 For continuous operations, once every 8
C2.2 2.11 Chemical Concentration Automatic/Manual hours. Otherwise, prior to start of each
2.12 production cycle.
C2.3 2.11 There is a dump schedule for conditioner. Manual Once per week

CQI-12
Related
Question #
3.0 Conversion Coating Bath
1.4
2.12
1.4 Temperature is monitored and controlled if required by

C3.2 2.11 chemical manufacturer's technical Automatic Once every 8 hours
2.12 data sheet.
Chemical Analysis:
- Phosphate: Free Acid, Total Acid, Iron Content, pH,
1.4
Accelerator Amount as Applicable
C3.3 2.11 Automatic/Manual Once every 4 hours
- Non-phosphate: Concentration, pH
2.12
- Chromate: Concentration, pH
- Non-chrome: Concentration, pH
1.4
Fluoride Ion Concentration (if aluminum is being
coated)
2.12
1.4
1.6
C3.5 Coating Weight/Thickness Manual Once every 8 hours*
2.11
2.12
1.4
C3.6 2.11 Crystal/Grain Size (If applicable) Manual Per customer requirement
2.12
Coverage of phosphate coating is visually inspected for

C3.7 Manual Once every 8 hours
absence of voids.

CQI-12
Related
Question #
4.0 Rinse After Phosphate
Cleanliness of last rinse

1.4
- visual inspection for suspended solids
2.12
- verify water flow (1/shift)
1.4
2.12
C4.3 2.11 There is a dump schedule for rinses. Manual Once per week

CQI-12
Related
Question #

1.4
2.12
1.4
C5.2 2.11 Chemical Concentration Automatic/Manual Once every 8 hours
2.12
1.4 Temperature is monitored and controlled if required by
C5.3 2.11 chemical manufacturer's technical Automatic Once every 8 hours
2.12 data sheet.
C5.4 2.11 There is a dump schedule for seal. Manual Once per week
6.0 Dry-Off (If Applicable)
1.4
C6.1 2.11 Air temperature is monitored and controlled. Automatic Once every 8 hours
2.12
1.4 There is a procedure to ensure dryness of parts prior to Every change of lot number and each
C6.2 Visual
2.11 subsequent coating. container.

CQI-12
PROCESS TABLE D - Powder Coating
Related
Question #
1.0 Powder Paint Application
1.4 Parts are checked exiting dry-off oven for cleanliness

D1.1 Manual Once every hour
2.11 and trapped water, prior to entering powder booth.
2.0 Powder Booth and Equipment
1.4
The temperature of parts entering the coating booth is
D2.1 2.11 Automatic/Manual Once every 8 hours
monitored.
2.12
Automatic Line: Confirm set-up at the start

of production and every process change.
1.4 Manually verify every 3 months or after
1.6 Conveyor speed set point is verified. If conveyor is not programming change or equipment
D2.2 Automatic/Manual
2.11 used, time in oven is verified. maintenance.
2.12
Manual Line: Continuously monitor time in
each stage of process.
1.4
The ground is checked using a 500 volt mega ohm At start-up, every process change and
D2.3 2.11 Manual
meter (less than 1megaohm resistance). once every 8 hours.
2.12
1.4
All guns are properly assembled (e.g., electrodes and Prior to the start of production and once
D2.4 2.11 Manual
deflectors are installed and not damaged). every 8 hours.
2.12

CQI-12
Related
Question #
1.4
The voltage and the current setting of the spray gun is At start-up, every process change and
D2.5 2.11 Manual
defined and verified for each process and part. once every 8 hours.
2.12
For automatic systems gun settings are defined and

verified for each process and part.
1.4 - Deflector
At start-up, every process change and
D2.6 2.11 - Gun to part distance Automatic
once every 8 hours.
2.12 - Number of guns
- Spacing of guns
- Reciprocator settings
1.4
The air dryer output temperature and dew point need to Prior to start of production and once every
1.17
D2.7 be measured. The filter on main compressed air line Automatic/Manual 4 hours. With a control alarm, frequency
2.11
needs to be monitored. may be reduced to once every 8 hours.
2.12
1.4
Prior to start of production and once every
1.17
D2.8 The booth temperature and humidity are checked. Automatic 4 hours. With a control alarm, frequency
2.11
may be reduced to once every 8 hours.
2.12

CQI-12
Related
Question #
1.4 Prior to start of production and once every

D2.9 2.11 The air balance in the powder booth is checked. Automatic/Manual 4 hours. With a control alarm, frequency
2.12 may be reduced to once every 8 hours.
1.4
1.17 Prior to the start of production and once
D2.10 Every sieve is clean and operational. Automatic/Manual
2.11 every 8 hours.
2.12
1.4
Prior to the start of production and once
D2.11 2.11 The powder flow on sieve is monitored. Automatic/Manual
every 8 hours.
2.12
1.4
D2.12 2.11 The feed hopper fluidizing air pressure is checked. Manual
every 8 hours.
2.12
1.4
D2.13 2.11 The dust vent on feed hopper is checked. Manual
every 8 hours.
2.12
1.4
1.17 Prior to the start of production and once
D2.14 The reclaim sieve is operating properly. Manual
2.11 every 8 hours.
2.12

CQI-12
Related
Question #
1.4
1.17 The venturis (orifice or block) in the feed pumps and Prior to the start of production and once
D2.15 Manual
2.11 the pick up tubes in the hopper are checked. every 8 hours.
2.12
1.4
The feed hoses are checked to ensure that they have Prior to the start of production and once
D2.16 2.11 Manual
no excessive bends and kinks. every 8 hours.
2.12
1.4 The virgin to reclaim powder ratio is defined for each

D2.17 2.11 part and/or process. Verified by feed pressures, weight Manual Once every 8 hours
2.12 or volume.
1.4
1.17 The pressure differential across the filters in the booth Prior to the start of production and once
D2.18 Automatic
2.11 collection chamber is monitored. every 8 hours.
2.12
1.4
D2.19 2.11 Sealing Rinse (if applicable) Manual
every 8 hours.
2.12
3.0 Cure (See Cure Process Table I)

CQI-12
PROCESS TABLE E - Spray
Related
Question #
1.0 Part Appearance
Pretreated parts are visually inspected for

1.4 cleanliness and/or uniform phosphate coating or
E1.1 Manual Once every 4 hours
2.11 paint layer (when applicable). This must be
performed between each coating layer.
1.4 Mutilation prevention items (i.e., gloves, belt buckle

E1.2 Manual Ongoing
2.9 covers, watch covers, etc.) are in place.
1.4
Paint racks and/or fixtures are visually inspected for
1.17
E1.3 cleanliness, excessive paint build-up, bent hooks, Manual Each time parts are racked/loaded.
2.11
etc.
2.12
1.4
1.17 There is a paint rack/fixture maintenance program.
E1.4 Manual Per preventative maintenance schedule.
2.11 Program must define rack/fixture cleaning intervals.
2.12
1.4
Surface profile is within specifications
E1.5 2.11 Manual Once every 4 hours
(if applicable).
2.13
1.4
Surface tension is within specifications
(if applicable).
2.13

CQI-12
Related
Question #
2.0 Paint Mixing
1.4 Paint mixing rooms are controlled (mixing tank

E2.1 2.11 grounding, closed container, properly enclosed Automatic/Manual Once every 8 hours
2.12 space, temperature, clean environment).
1.4 There is a stock rotation system (FIFO) in place and

E2.2 2.11 being utilized to ensure that older material is used Manual Continuous
2.12 first.
1.4
1.6
Paint agitation/time and reduction (solvent package)
are proper and documented.
2.11
2.12
1.4
Prior to start of production and every
1.6
Viscosity is verified to be within operational limits process change and/or addition. For
E2.4 1.17 Manual
and documented. continuous operations check once every 8
2.11
hours.
2.12
1.4
1.6
Temperature is verified to be within operational process change and/or addition. For
E2.5 1.17 Automatic/Manual
limits and documented. continuous operations check once every 8
2.11
hours.
2.12

CQI-12
Related
Question #
1.4
1.6
E2.6 1.17 The proper filter size and type are in place. Manual
process change.
2.11
2.12
1.4
1.6 Pump pressures are set and pressure readings are
Prior to start of production, every process
E2.7 1.17 verified and documented to be within operational Manual
change and once every 8 hours.
2.11 limits.
2.12
1.4
Circulation (flow meter, pressure gage) is monitored Prior to start of production, every process
and documented. change and once every 8 hours.
2.12
Filters are in use (not by-passed) and pressures

1.4
monitored. Filters are changed before pressure Prior to start of production, every process
differential exceeds 10 PSI. change and once every 8 hours.
2.12
(70 kPa)

CQI-12
Related
Question #
3.0 Primer/Promoter
1.4
1.17 Prior to start of production, every process
E3.1 Destaticizing air is operational. (Plastic parts only). Automatic
2.11 change and once every 8 hours.
2.12
1.4
Booth balance (air flow) is monitored and Prior to start of production, every process
E3.2 2.11 Manual
documented. change and once every 8 hours.
2.12
1.4
1.6
Booth temperature and humidity are monitored and Prior to start of production, every process
2.11
2.12
1.4
1.6 Atomizer parameters (fluid flow, air pressures Prior to start of production and every
E3.4 1.17 (atomizing fan, shaping), electrostatics and mixing) Automatic/Manual process change. For continuous
2.11 are set within operational limits. operations once per day.
2.12
For manual process, prior to start of

production and every process change.
1.4
E3.5 Time is verified and documented if applicable. Automatic/Manual
1.6 For automated process, verify once per
month, or after every program change or
major maintenance.

CQI-12
Related
Question #
4.0 Basecoat (If applicable)
1.4
1.6 Flashtimes between coats are set at suppliers At the start of production and every
E4.1 Automatic/Manual
2.11 recommended times. process change.
2.13
1.4
1.6
2.11
2.12
1.4
2.12

1.4
1.6 For automated process, verify 1 per
major maintenance.

CQI-12
Related
Question #
Basecoat Heated Flash

5.0
(Waterborne Materials Only)
1.4 Oven set point(s) and energy type

1.6 (Convection/IR/UV/etc.), are verified to be within
E5.1 Manual process change. For continuous
2.11 chemical suppliers recommended limits and
operations once every 8 hours.
2.12 documented.
1.4 Prior to start of production and every two

1.6 hours. With a temperature control alarm,
E5.2 Oven temperature is monitored and recorded. Automatic
2.11 frequency may be reduced to once every 8
2.12 hours.
1.4
For each coating in use, proper cure or drying time
1.6 Every three months and after oven
E5.3 parameters are verified based upon product Manual
2.11 modification or repair.
technical data sheet.
2.12
E5.4 1.17 Air filter (if used) change is scheduled. Manual Per preventative maintenance schedule.
1.4
1.6 Percent solids after pre-dry is at the suppliers
E5.5 Manual Once every 8 hours
2.11 recommended percentage.
2.13

CQI-12
Related
Question #
6.0 Clear coat
1.4
1.6 Flashtimes between coats are set at suppliers At the start of production and every
E6.1 Automatic/Manual
2.11 recommended times. process change.
2.13
1.4
1.6
2.11
2.12
1.4
2.12

1.4
1.6 For automated process, verify 1 per
major maintenance.

CQI-12
PROCESS TABLE F - Electrocoat
Related
Question #
1.0 Pre-Electrocoat Paint Application Part Appearance
1.4 Pretreated parts are visually inspected for cleanliness and/or

F1.1 Manual Once every 8 hours
2.11 uniform phosphate coating (when phosphate is used).
2.0 Electrocoat Tank
1.4
Bath parameters (pH, conductivity, solid content, temperature,
F2.1 2.11 Automatic/Manual Once every 8 hours
voltage) are checked and adjusted.
2.12
1.4
Oil contamination (Panel inspection for pin holes). Once per month and if any visual defects
F2.2 2.11 Manual
Oil bags must be available. are observed.
2.12
1.4 For manual process, prior to start of

1.6 production and every part change. For
F2.3 Cycle time/Line speed setup is checked. Automatic/Manual
2.11 automated process, at the start of
2.12 production and every process change.
1.4 Once every 4 hours. With a control alarm,

Is bath circulation monitored.
F2.4 2.11 Automatic/Manual frequency may be reduced to once every 8
(Flow meter, pressure gage)
2.12 hours.
Bag filters are in use (not by-passed) and pressures monitored.

1.4
Filter bags changed before pressure differential exceeds 10
F2.5 2.11 Manual Once every 8 hours
PSI. (70 kPa)
2.12
Filter mesh size must be 25 µm maximum.
1.4
F2.6 2.11 Flow over the weir is verified. Manual Once every 8 hours
2.12
1.4
F2.7 2.11 Bath is checked for microbial contamination. Manual Once every month*
2.12
1.4
Incoming DI / RO water is checked for cleanliness. (Conductivity
<10 µS/µmhos )
2.12

CQI-12
Related
Question #
1.4
1.17 Paint racks and/or barrels are visually inspected for cleanliness,
F2.9 Manual Each time parts are racked/loaded
2.11 excessive paint build-up, bent hooks, etc.
2.12
1.4
1.17 There is a paint rack/barrel maintenance program. Program
F2.10 Manual Per preventative maintenance schedule.
2.11 must define rack/barrel cleaning intervals.
2.12
1.4
F2.11 2.11 Saddle contact cleanliness (if applicable). Manual Once every 8 hours
2.12
1.4
1.17
F2.12 There is a tank cleaning and maintenance schedule. Manual Once every year
2.11
2.12
1.4
F2.13 2.11 Confirmation of ash content (pigment to binder ratio). Manual Once per month
2.12
1.4
F2.14 2.11 Analysis of accumulation of metallic impurities. Manual Once every 6 months
2.12

CQI-12
Related
Question #
1.4
F3.1 2.11 The conductivity of the anolyte solution has been measured. Manual Once every 8 hours
2.12
1.4
F3.2 2.11 The pH of the anolyte solution has been measured. Manual Once every 8 hours
2.12
1.4
Oil contamination (Panel inspection for pin holes).
F3.3 2.11 Manual Once every month
Oil bags must be available.
2.12
1.4
F3.4 2.11 The anolyte solution is being circulated to each cell. Automatic/Manual Once every 8 hours
2.12
1.4
F3.5 2.11 Dump and clean schedule for anolyte is being maintained. Manual Per preventative maintenance schedule.
2.12
1.4
F3.6 2.11 Amperage draw has been checked on anodes. Automatic/Manual Per preventative maintenance schedule.
2.12
4.0 Rectifier
1.4
1.6 The proper voltage is being used for the load size. When each bar or rack enters the coating
F4.1 Manual
2.11 (Electronically Controlled with digital read-out) tank.
2.12
1.4
Once every 6 months or after any change
F4.2 2.11 The ramp up time to full voltage has been verified. Automatic/Manual
or maintenance of rectifier.
2.12
There is a visual indicator to alert personnel when system is

F4.3 2.10 Automatic Ongoing
energized.

CQI-12
Related
Question #
1.4
1.17 The ripple of the rectifier has been checked by an approved Once per year or after any change or
F4.4 Automatic/Manual
2.11 electrician. maintenance of rectifier.
2.12

CQI-12
Related
Question #
5.0 Rinse System
1.4
Immersion rinse tanks are operating at the proper levels and
tanks are being agitated correctly.
2.12
1.4
F5.2 2.11 There is sufficient permeate supplied to the rinse. Automatic/Manual Once every 8 hours
2.12
1.4
The pH and conductivity of the DI rinse water are measured. (If
part of production process).
2.12
1.4
Ultra filters are in use (not by-passed) and pressures monitored.
2.12
Bag filters are in use (not by-passed) and pressures monitored.

1.4
Filter bags changed before pressure differential exceeds 10
PSI. (70 kPa)
2.12
Filter mesh size must be 25 µm maximum.
1.4
1.17 Rinse tanks and related equipment are emptied, inspected and
F5.6 Manual Per preventative maintenance schedule.
2.11 cleaned.
2.12

CQI-12
PROCESS TABLE G - Dip/Spin
Related
Question #
1.0 Coating Material Application
Final pretreatment and/or phosphating shall be

G1.1 2.9 Yes/No Ongoing
completed in the same building.
1.4 After pretreatment, parts are inspected for flash rust,

G1.2 Manual Every lot
2.11 wetness, oil or other defects.
Pretreated parts are visually inspected for cleanliness

1.4
G1.3 and/or uniform phosphate coating (when phosphate is Automatic/Manual Once every 8 hours
2.11
used).
1.17 Containers used to hold parts between coating

G1.4 2.6 operations are free of oil, grease or other Yes/No Ongoing
2.9 contaminants.
Parts shall be stored indoors in a staging area that

does not affect the quality of parts. The staging area
G1.5 2.9 shall not be adjacent to open doorways or windows Yes/No Ongoing
exposing parts to water, dirt, and other
contaminations.
1.4 Parts shall be coated within the time limit specified by

G1.6 Per application manual Ongoing
2.11 the chemical supplier application manual.
1.4 Prior to loading into coating machines, parts are

G1.7 Manual Every lot
2.11 inspected for flash rust, wetness, oil or other defects.

CQI-12
Related
Question #
2.0 Coating Bath

1.4
G2.1 2.11 Incoming paint viscosity is checked. Manual Each new lot of paint
2.12
1.4
G2.2 2.11 Incoming solids checks are performed. Manual Each new lot of paint
2.12
1.4
1.17 Appropriate mixing equipment is used, capable of
G2.3 Manual Ongoing
2.11 dispersing settled solids.
2.12
2.9 Coating material (paint) must be stored per chemical

G2.4 Manual Ongoing
2.10 supplier requirements.
When not in use, coating material (paint) is kept

2.9
G2.5 covered and/or sealed per chemical supplier Manual Ongoing
2.10
requirements.
2.9 Paint storage area is clean and organized so each

G2.6 Manual Ongoing
2.10 paint is easily found and to prevent contamination.
2.9 Preventive maintenance

G2.7 Paint filtration procedures are in place. Ongoing
2.10 schedule
The following checks shall be performed during

G2.8
production:
1.4
Prior to start of production and once every 3
G2.9 2.11 Paint Temperature Automatic/Manual
hours.
2.12

CQI-12
Related
Question #
1.4
G2.10 2.11 Viscosity Manual
hours.
2.12
1.4 Prior to start of production and every process

G2.11 2.11 Basecoat % Solids (by weight). Manual change and/or addition. For continuous
2.12 operations once per day.
1.4
G2.12 2.11 Volume (paint depth in coating vat). Automatic/Manual
hours.
2.12
1.4 Equipment surfaces in contact with wet coating (ex.

G2.13 2.11 Vibratory feed tables) are free of loose debris and Manual Once per day
2.12 excess coating build-up.
1.4
1.17 Basket condition (basket mesh clean and
G2.14 Manual Once per day
2.11 undamaged).
2.12
1.4 Paint and/or viscosity reducing agent additions are

G2.15 2.11 documented and the viscosity verified before Manual Each addition
2.12 production continues.
G2.16 2.10 Viscosity cups are cleaned after each use. Manual Ongoing
2.14 Viscosity cups are verified against calibrated

G2.17 Manual Twice per month
1.17 standards or master cup.
2.14 Thermometers are verified against calibrated

G2.18 Manual Once per month
1.17 standards.

CQI-12
Related
Question #
3.0 Application Parameters
A system is in place to ensure proper basket weights

1.4
G3.1 for specific parts, such as processing manual, traveler, Automatic/Manual Every lot
1.6
or process recipe.
1.4
G3.2 Baskets are kept less than 2/3 full by volume. Automatic/Manual Every lot
1.6
Coating parameters are controlled and verified via

1.4
G3.3 external display (dip time, spin speed, spin time, spin Automatic/Manual Every lot
1.6
cycle, spin direction and tumbling).
There is a system (raking, vibe table, etc.) to uniformly

1.4
distribute parts prior to curing to ensure proper cure
G3.4 1.6 Automatic/Manual Every lot
and prevent parts from sticking and minimize touch
1.17
marks.
G3.5 2.10 Vibratory feed tables are cleaned (if used). Manual As needed
There is evidence of steps taken to assist in soft

G3.6 2.9 handling of parts (shallow drops, lined chutes and Automatic/Manual Every lot
hoppers, bumper boards, etc.).
1.4
G3.7 2.9 Parts are cool to touch before each coating step. Manual Every lot
2.11

CQI-12
PROCESS TABLE H - Autodeposition
Related
Question #
1.0 Coating Bath
1.4
Mixer speed and direction are monitored and
H1.1 2.11 Automatic/Manual Once every 8 hours
adjusted.
2.12
1.4
1.6 Temperature of the coating bath is continuously Continuous monitoring by controller and
H1.2 Automatic
2.11 monitored and controlled. manually verified once per day.
2.12
1.4
Misting nozzles in the vicinity of the coating bath
are operational.
2.12
1.4
Acid (e.g., 101 meter) and oxidation/reduction
potential (ORP) levels are checked.
2.12
1.4
Chemical concentration (% solids, starter/iron
titration, conductivity) is checked and maintained.
2.12
1.4
1.17 Coating tank, mixers and heating/cooling system
H1.6 Manual Once every 12 months
2.11 are inspected and maintained.
2.12

CQI-12
PROCESS TABLE H - Autodeposition
Related
Question #
2.0 Tap Rinse After Coating
1.4
H2.1 2.11 Pump pressure or agitator speed is monitored. Automatic/Manual Once every 8 hours
2.12
1.4
H2.2 2.11 Impurity concentration (conductivity) is checked. Automatic/Manual Once every 8 hours
2.12
3.0 Reaction Rinse
1.4
Chemical concentration is checked and
maintained.
2.12
1.4
H3.2 2.11 Pump pressure or agitator speed is monitored. Automatic/Manual Once every 8 hours
2.12
1.4 Temperature is monitored and controlled if

H3.3 2.11 required by chemical manufacturer's technical Automatic/Manual Once every 8 hours
2.12 data sheet.
1.4
1.17 Per Chemical Manufacturer's
H3.4 There is a dump schedule. Manual
2.11 recommendation and production volume.
2.12

CQI-12
PROCESS TABLE I - Cure
Item # Related
CSA Category/Process Steps Type of Control Monitoring Frequency Observation/Comments
Question #
1.0
Oven conditions are monitored and recorded continuously by a

data recorder. Prior to start of production and once every
I1.1 Convective - Temperature Automatic 2 hours. With a control alarm, frequency
Gas IR - Gas flow may be reduced to once every 8 hours.
Electric IR - Power (wattage)
Oven and part temperature profile is verified. The verification

shall be performed under production load conditions and with Once every 3 months and after oven
I1.2 Manual
thermocouples located to cover all areas of the part curing modification or repair.
window.
1.4
For each coating in use, proper cure or drying time parameters
1.6 Once every 3 months and after oven
I1.3 are verified based upon oven temperature profile and product Manual
2.11 modification or repair.
technical data sheet.
2.12
1.4
1.6
Conveyor speed set point is verified. If conveyor is not used, production and every part change. For
I1.4 1.17 Automatic/Manual
time in oven is verified. automated process, at the start of
2.11
2.12
Per oven manufacturer, filter supplier

I1.5 Air filter (if used) change is scheduled. Manual
recommendation.
Cure testing is performed per part specification on a production At oven start-up, every process change
I1.6 2.13 Manual
part. and once every 8 hours.
Coating adhesion test is performed per part specification on a At oven start-up, every process change
I1.7 2.13 Manual
production part. and once every 8 hours.
Appearance requirements checks (color, gloss etc.) are At oven start-up, every process change
I1.8 2.13 Manual
performed per part specification. and once every 8 hours.

CQI-12
PROCESS TABLE J: Anodizing and Hard Coat Anodizing
* When historical results show capability, test frequency may be reduced.
Related
Question #
1.0 Cleaning (Alkaline or Acid)

1.4
J1.1 2.11 Temperature Automatic
2.12
1.4
J1.2 2.11 Cleaner Concentration Manual Once per day *
2.12
1.4
J1.3 2.11 Soil loading ( i.e., acid split, alkalinity ratio) Manual Once per day *
2.12

1.4 production and every process change. *
J1.4 2.11 Time Automatic or Manual
2.12 For automated process, verify after every
program change or major maintenance.
1.4
J1.5 2.11 Agitation (Consistent Across tank) Automatic Once every 8 hours
2.12
1.4
J1.6 2.11 Solution Level Automatic or Manual Once every 8 hours
2.12
1.4
J1.7 2.11 Skimmer Weir Level/oil separator function Automatic or Manual Once every 8 hours
2.12

CQI-12
Related
Question #
1.4
J1.8 2.11 Oil on top of tank Manual Once every 8 hours
2.12
1.4
J1.9 2.11 Debris in bottom of tank Manual Once every 8 hours
2.12
1.4
J1.10 2.11 Metal Contamination (as applicable) Manual Once every 8 hours
2.12
2.0 Rinsing
1.4
2.12
1.4
Contamination accumulation/build up on side
J2.2 2.11 Manual Visual Once per week *
of tanks
2.12
1.4
There is a process for control of biological
J2.3 2.11 Manual Once per week *
contamination
2.12
1.4
J2.4 2.11 Automatic/Manual Once every 8 hours
Agitation or flow for immersion tanks.
2.12
1.4
J2.5 2.11 Temperature (if controlled) Automatic
2.12

1.4 production and every process change.

CQI-12
Related
Question #
Cleanliness of last rinse

1.4
- visual inspection for oil or suspended
J2.7 2.11 Manual Once per day
contaminants
2.12
- overflow
- debris in bottom of tank
J2.8 2.11 There is a dump schedule for rinses. Manual Per preventative maintenance schedule.
3.0 Deoxidizer / Desmutter
1.4
J3.1 2.11 Temperature (if applicable) Automatic or Manual
2.12
1.4
J3.2 2.11 Concentration Manual Once per day *
2.12
1.4
J3.3 2.11 Acidity Ratio (Total Acid/ Free Acid = Ratio) Manual Once per day *
2.12

1.4 production and every process change. *
1.4
2.12
1.4
2.12
1.4
J3.7 2.11 Debris in bottom of tank Manual Once per day
2.12

CQI-12
Related
Question #
4.0 Chemical Etch / Strip (alkaline or acid)
1.4
2.12
1.4
2.12
1.4
Contamination:
J4.3 2.11 Manual Once per day *
For alkaline: aluminum content
2.12
1.4
Contamination accumulation/build up on side
J4.4 2.11 Manual Once per week
of tanks
2.12
1.4 For acid etches only:

J4.5 2.11 Ratio (Total Acid/ Free Acid = Ratio) Manual Once per day *
2.12 For acid: fluoride content
For manual process: every load.

1.4
For automated process, verify after every
2.12
process change or major maintenance.
1.4
2.12
1.4
2.12
1.4
J4.9 2.11 Debris in bottom of tank Manual Once per day
2.12

CQI-12
Related
Question #
5.0 Bright Dip
Continuous monitoring by controller with

1.4
low temperature alarm. Manually verify
J5.1 2.11 Temperature Automatic or Manual
prior to start of production and once every
2.12
4 hours.
1.4
J5.2 2.11 Acid concentration Manual Once every 4 hours
2.12
1.4
J5.3 2.11 Specific gravity Manual Once every 4 hours
2.12
1.4
J5.4 2.11 Contamination: aluminum content Manual Once per week
2.12
1.4
Contamination accumulation, suspended
J5.5 2.11 Manual Once per day
solids
2.12

1.4
2.12
1.4
2.12
1.4
2.12

CQI-12
Related
Question #
6.0 Bright Dip Rinse
1.4
J6.1 2.11 Acid concentration or specific gravity Manual Once every 8 hours
2.12
1.4
J6.2 2.11 Time Automatic or Manual Once every 8 hours
2.12
1.4
J6.3 2.11 Agitation (Consistent Across Tank) Manual Once every 8 hours
2.12
1.4
2.12
1.4
J6.5 2.11 Debris in bottom of tank Manual Once per week
2.12
1.4
J6.6 2.11 Temperature Automatic or Manual Once per day
2.12

CQI-12
Related
Question #
7.0 Anodizing
1.4
2.12
1.4
J7.2 2.11 Acid Concentration Manual Once every 8 hours *
2.12
1.4 Concentration of additives (fume

J7.3 2.11 suppressant, hard coat additives, high Manual Once per week
2.12 temperature additives)
1.4
J7.4 2.11 Aluminum Content (maximum 20 g/L) Manual Once per week
2.12

1.4
2.12

CQI-12
Related
Question #
1.4
J7.6 2.11 Agitation (Consistent Across tank) Manual Once every 8 hours
2.12
1.4
2.12
1.4
J7.8 2.11 Debris in bottom of tank Manual Once per week
2.12

1.4
Voltage or Amperage with Gradual Ramp Up
J7.9 2.11 Automatic or Manual
(Current Increase) For automated process, verify after every
2.12
process change and major maintenance.
1.4
J7.10 2.11 Saddle Contact Cleanliness Manual Once every 8 hours
2.12

CQI-12
Related
Question #
8.0 Dye
1.4
2.12
1.4
2.12
1.4
J8.3 2.11 pH Manual Once every 8 hours *
2.12

1.4
2.12
1.4
J8.5 2.11 Agitation (as applicable) Automatic Once every 8 hours
2.12
1.4
2.12
1.4
2.12
1.4
There is a process for control of biological
contamination.
2.12

CQI-12
Related
Question #
9.0 Pre-Seal (If applicable)
1.4
2.12
1.4
J9.2 2.11 Concentration Manual Once per week *
2.12
1.4
2.12

1.4
2.12
1.4
J9.5 2.11 Agitation (as applicable) Automatic Once every 8 hours
2.12
1.4
2.12
1.4
2.12

CQI-12
Related
Question #
10.0 Seal (if Applicable)

1.4
2.12
1.4
J10.2 2.11 Temperature Automatic or Manual
Manually verify every 4 hours if controlled.
2.12
1.4
J10.3 2.11 Concentration Manual Once every 8 hours *
2.12
1.4
2.12
1.4
Contamination (per chemical vendor
recommendation)
2.12
1.4
J10.6 2.11 Agitation (as applicable) Manual Once every 8 hours
2.12
1.4
2.12
1.4
2.12

CQI-12
PROCESS TABLE K - EQUIPMENT
Related Pretreatment/ Calibration /

Powder Included in Preventative
Item # CSA Equipment Type Aqueous E-Coat Spray Dip/Spin A-Coat Cure Anodize Verification Frequency Certification Comment
Coat Maintenance Plan
Question # Cleaning Frequency *
PROCESS EQUIPMENT
K1.1 2.14 pH / Conductivity Meter X X X X X X Daily Once per year
pH / Conductivity Probe
K1.2 2.14 Solution compatible probes must X Before each use N/A
be used.
K1.3 2.14 Temperature Controller X X X X X X X X Every 3 months N/A

Ripple Checked every 12
K1.4 2.14 Rectifier X X N/A
months
K1.5 2.14 Amp Meter/Volt Meter X X X X X X Checked every 12 months N/A
Wet Analysis:
Before use, chemicals must be
K1.6 2.14 X X X X X X Daily N/A
checked for shelf life and/or
expiration date
K1.7 2.14 Filters X X X X X X X Per process table N/A

Laboratory Balance (Weight
K1.8 2.14 X X X X Once per month N/A
Scale)
K1.9 2.14 Conductivity Meter X X X X X X Once per month N/A
K1.10 2.14 Viscosity cup X X Twice per month N/A
K1.11 Thermocouple X X X X X X X N/A Once every 6 months
K1.12 2.14 Lab Oven Controller X X X X X X N/A Once per year

MINIMUM REQUIRED TESTING CAPABILITY
K2.1 2.14 Salt Spray Cabinet X X X X X X X X Daily per ASTM B117 N/A
K2.2 2.14 Water Immersion bath X X X X X Daily N/A
K2.3 2.14 Cure Testing X X X X X X Per Part N/A

K2.4 2.14 Adhesion Testing X X X X X X Per Part N/A
K2.5 2.14 Thickness Testing X X X X X X Per Part Once per year
K2.6 2.14 Solids Testing X X X X X Daily N/A

CQI-12
PROCESS TABLE L - Part Inspection and Testing
The customer may have additional requirements, e.g., inspection testing, greater frequencies, etc. When performing the job audit, the auditor shall verify coater is conforming to specifications or other
requirements.
Note that not all tests are applicable to all coatings.
Related
Item # CSA Category/Process Steps Monitoring Frequency Observation/Comments
Question #
Minimum Requirement Actual Condition (Pass / Fail / N/A)
1.0
Procedures are in place to prevent damage to the finish or part

L1.1 1.4 System in place
during the inspection and packaging processes.
Appearance of the coating shall be verified per specification and

L1.2 Ongoing
applications manual.
Initial adhesion At the start of production and once every

L1.3
(Tape, bend, impact) 8 hours.
L1.4 Intercoat / final adhesion Per customer specification
At the start of production and once every

L1.5 Color and Gloss (If applicable)
8 hours.
At the start of production, every part family

L1.6 Film thickness / coating weight change and every process change. Once
every 8 hours.

CQI-12
PROCESS TABLE L - Part Inspection and Testing
The customer may have additional requirements, e.g., inspection testing, greater frequencies, etc. When performing the job audit, the auditor shall verify coater is conforming to specifications or other
requirements.
Note that not all tests are applicable to all coatings.
Related
Item # CSA Category/Process Steps Monitoring Frequency Observation/Comments
Question #
Minimum Requirement Actual Condition (Pass / Fail / N/A)
Once per week per line per coating

Corrosion resistance: process being used.
- Neutral salt spray If the same coating system is used for
L1.7
- Humidity multiple customers with different
- Water immersion requirements, test to the highest
requirement.
Once per week per line per coating

L1.8 Torque tension/Coefficient of Friction
process being used.
L1.9 Dimensional check (e.g., Go-no go, Plug and Ring gage) Per customer specification
L1.10 Hydrogen Embrittlement Per customer specification
L1.11 Cyclical Corrosion Testing Per customer specification

CQI-12 Coating System 3-29-16

Uploaded by

Copyright:

Available Formats

CQI-12 Coating System 3-29-16

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CQI-12 Coating System 3-29-16

Uploaded by

Copyright:

Available Formats

CQI-12v2

Special Process: Coating System Assessment

AIAG Copyright and Trademark Notice:

© 2012 Automotive Industry Action Group

© 2012 Automotive Industry Action Group

Special Process: Coating System Assessment 2nd Edition

Phone Number: Type(s) of Coating Processes at this Facility:

Date of Re-assessment (if necessary):

Number of "Not Satisfactory" Findings:

Number of "Needs Immediate Action" Findings:

Number of "Fail" Findings in the Job Audit(s):

Number of Process Table Items not meeting Minimum Requirements:

© 2012 AIAG (Automotive Industry Action Group)

Special Process: Coating System Assessment (General Facility Overview)

Question Needs Immediate

Section 1 - Management Responsibility and Quality Planning

To ensure readily available expertise, there shall be a

The coater shall incorporate a documented advanced

© 2012 AIAG (Automotive Industry Action Group)

Special Process: Coating System Assessment (General Facility Overview)

Question Needs Immediate

The coater shall incorporate the use of a documented

The coater shall incorporate the use of a documented

© 2012 AIAG (Automotive Industry Action Group)

Special Process: Coating System Assessment (General Facility Overview)

Question Needs Immediate

To ensure all customer requirements are both

The coater shall have written process specifications for

© 2012 AIAG (Automotive Industry Action Group)

Special Process: Coating System Assessment (General Facility Overview)

Question Needs Immediate

To demonstrate each process is capable of yielding

The analysis of products and processes over time can

Are internal assessments

© 2012 AIAG (Automotive Industry Action Group)

Special Process: Coating System Assessment (General Facility Overview)

Question Needs Immediate

The quality management system shall include a

The quality management system shall include a

The coater shall define a process for continual

Does the Quality Manager or

© 2012 AIAG (Automotive Industry Action Group)

Special Process: Coating System Assessment (General Facility Overview)

Question Needs Immediate

There shall be procedures or work instructions

The coater shall provide employee training for all

The coater shall maintain a responsibility matrix

© 2012 AIAG (Automotive Industry Action Group)

Special Process: Coating System Assessment (General Facility Overview)

Question Needs Immediate

The coater shall have a documented preventive

Has the coater developed a

© 2012 AIAG (Automotive Industry Action Group)

Special Process: Coating System Assessment (General Facility Overview)

Question Needs Immediate

Section 2 - Floor and Material Handling Responsibility

Procedures for part and container identification help to

Out-going lot(s) shall be traceable to the incoming

The control of suspect or non-conforming product is