SAFETY DATA SHEET

 
 

  1. Identification
Product identifier Pro Still Clean Distiller Cleaner & Descaler
Other means of identification Not available.
Recommended use Water Processing Equipment Cleaner
Recommended restrictions None known.
Manufacturer information Pro Products LLC
6714 Pointe Inverness Way
Suite 200
Fort Wayne, IN 46804-7935 US
Phone: 260-483-2519
Emergency Phone: 1-800-424-9300 (CHEMTREC)
Supplier See above.
 
  2. Hazard identification
Physical hazards Corrosive to metals Category 1
Health hazards Skin corrosion/irritation Category 1
Serious eye damage/eye irritation Category 1
Environmental hazards Not classified.
WHMIS 2015 defined hazards Not classified
Label elements

Signal word Danger

Hazard statement May be corrosive to metals. Causes severe skin burns and eye damage.
Precautionary statement
Prevention Keep only in original packaging. Do not breathe dust. Wash thoroughly after handling. Wear
protective gloves, protective clothing, eye protection and face protection.
Response Absorb spillage to prevent material-damage. IF SWALLOWED: Rinse mouth. Do NOT induce
vomiting. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with
water or shower. Wash contaminated clothing before reuse. IF INHALED: Remove person to
fresh air and keep comfortable for breathing. Immediately call a POISON CENTER or doctor.
Specific treatment (see information on this label). IF IN EYES: Rinse cautiously with water for
several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Storage Store in a corrosion resistant container with a resistant inner liner. Store locked up.
Disposal Dispose of container in accordance with local, regional, national and international regulations.
WHMIS 2015: Health Hazard(s) None known
not otherwise classified
(HHNOC)
WHMIS 2015: Physical None known
Hazard(s) not otherwise
classified (PHNOC)
Hazard(s) not otherwise None known.
classified (HNOC)
Supplemental information Not applicable.
 
  3. Composition/Information on ingredients
Mixture
  Chemical name Common name and synonyms CAS number %
  Citric Acid 77-92-9 10-30*
  Silicic acid, aluminum sodium salt 1344-00-9 0.1-1*
  Sulfamic acid 5329-14-6 65-85*
All
  concentrations are in percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume.
#24470 Page: 1 of 8 Issue date 07-November-2019
Composition comments US GHS: The exact percentage (concentration) of composition has been withheld as a trade
secret in accordance with paragraph (i) of §1910.1200.

*CANADA GHS: The exact percentage (concentration) of composition has been withheld as a
trade secret.
 
 

  4. First-aid measures
Inhalation IF INHALED: Remove person to fresh air and keep comfortable for breathing. Immediately call a
POISON CENTER or doctor.
Skin contact IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water. Wash
contaminated clothing before reuse. Specific treatment (see information on this label). Immediately
call a POISON CENTER or doctor.
Eye contact IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present
and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor.
Ingestion IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Immediately call a POISON CENTER or
doctor.
Most important Burning pain and severe corrosive skin damage. Causes serious eye damage. Symptoms may
symptoms/effects, acute and include stinging, tearing, redness, swelling, and blurred vision. Permanent eye damage including
delayed blindness could result.
Indication of immediate Provide general supportive measures and treat symptomatically. Symptoms may be delayed.
medical attention and special
treatment needed
General information Ensure that medical personnel are aware of the material(s) involved and take precautions to
protect themselves. If you feel unwell, seek medical advice (show the label where possible). Show
this safety data sheet to the doctor in attendance. Avoid contact with eyes and skin. Wear rubber
gloves and chemical splash goggles. Keep out of reach of children.
 
  5. Fire-fighting measures
Suitable extinguishing media Carbon dioxide. Water spray. Dry chemical powder. Foam.
Unsuitable extinguishing None known.
media
Specific hazards arising from Firefighters should wear a self-contained breathing apparatus.
the chemical
Special protective equipment Firefighters should wear full protective clothing including self-contained breathing apparatus.
and precautions for firefighters
Fire-fighting In the event of fire, cool tanks with water spray. Cool containers with flooding quantities of water
equipment/instructions until well after fire is out.
Specific methods Cool containers exposed to flames with water until well after the fire is out.
Hazardous combustion May include and are not limited to: Oxides of carbon. Oxides of nitrogen. Oxides of sulfur.
products Ammonia.
 
  6. Accidental release measures
Personal precautions, Keep unnecessary personnel away. Keep out of low areas. Keep people away from and upwind of
protective equipment and spill/leak. Wear appropriate protective equipment and clothing during clean-up. Do not touch
emergency procedures damaged containers or spilled material unless wearing appropriate protective clothing. Ensure
adequate ventilation. Local authorities should be advised if significant spillages cannot be
contained. For personal protection, see section 8 of the SDS.
Methods and materials for Stop the flow of material, if this is without risk. Absorb spillage to prevent material damage. Use
containment and cleaning up water spray to reduce vapors or divert vapor cloud drift. Large Spills: Wet down with water and
dike for later disposal. Prevent entry into waterways, sewer, basements or confined areas.
Following product recovery, flush area with water. For waste disposal, see section 13 of the SDS.
Prevent entry into waterways, sewers, basements or confined areas.
Environmental precautions Do not discharge into lakes, streams, ponds or public waters.
 
  7. Handling and storage
Precautions for safe handling Use only with adequate ventilation. Avoid breathing dust. Avoid prolonged exposure. Wear
appropriate personal protective equipment. Wash thoroughly after handling. Use good industrial
hygiene practices in handling this material. Do not get in eyes, on skin or on clothing.
Conditions for safe storage, Store locked up. Store in corrosive resistant container with a resistant inner liner. Store in a closed
including any incompatibilities container away from incompatible materials. Keep only in the original container. Store in a cool,
dry place out of direct sunlight. Keep out of the reach of children.

 
#24470 Page: 2 of 8 Issue date 07-November-2019
  
  8. Exposure controls/Personal protection
Occupational exposure limits
Canada. Alberta OELs (Occupational Health & Safety Code, Schedule 1, Table 2)
 
Components
 
Type Value
Silicic acid, aluminum TWA 2 mg/m3
sodium salt (CAS
1344-00-9)
Canada. British Columbia OELs. (Occupational Exposure Limits for Chemical Substances, Occupational Health and
Safety Regulation 296/97, as amended)
 
Components Type Value Form
Silicic acid, aluminum TWA 1 mg/m3 Respirable.
sodium salt (CAS
1344-00-9)
Canada. Manitoba OELs (Reg. 217/2006, The Workplace Safety And Health Act)
 
Components Type Value Form
Silicic acid, aluminum TWA 1 mg/m3 Respirable fraction.
sodium salt (CAS
1344-00-9)
Canada. Ontario OELs. (Control of Exposure to Biological or Chemical Agents)
 
Components Type Value Form
Silicic acid, aluminum TWA 1 mg/m3 Respirable fraction.
sodium salt (CAS
1344-00-9)
Canada. Quebec OELs. (Ministry of Labor - Regulation respecting occupational health and safety)
 
Components Type Value
Silicic acid, aluminum TWA 2 mg/m3
sodium salt (CAS
1344-00-9)
 
US. ACGIH Threshold Limit Values
 
Components Type Value Form
Silicic acid, aluminum TWA 1 mg/m3 Respirable fraction.
sodium salt (CAS
1344-00-9)
US. NIOSH: Pocket Guide to Chemical Hazards
 
Components Type Value
Silicic acid, aluminum TWA 2 mg/m3
sodium salt (CAS
1344-00-9)
 
Biological limit values No biological exposure limits noted for the ingredient(s).
Exposure guidelines This material does not have established exposure limits.
Appropriate engineering Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
controls should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level.
Individual protection measures, such as personal protective equipment
Eye/face protection Wear safety glasses with side shields (or goggles) and a face shield.
 
Skin protection
Hand protection Impervious gloves. Confirm with reputable supplier first.
Other As required by employer code. Rubber apron recommended.
Respiratory protection Where exposure guideline levels may be exceeded, use an approved NIOSH respirator.
Respirator should be selected by and used under the direction of a trained health and safety
professional following requirements found in OSHA's respirator standard (29 CFR 1910.134),
CAN/CSA-Z94.4 and ANSI's standard for respiratory protection (Z88.2).
Thermal hazards Not applicable.
General hygiene Always observe good personal hygiene measures, such as washing after handling the material
considerations and before eating, drinking, and/or smoking. Routinely wash work clothing and protective
equipment to remove contaminants. Wash hands before breaks and immediately after handling
the product.

 
#24470 Page: 3 of 8 Issue date 07-November-2019
 
  9. Physical and chemical properties
Appearance Free-flowing Powder.
Physical state Solid.
Form  
Solid.
Color Yellow
Odor Odorless
Odor threshold Not available.
pH 0.89 (10% w/w), Acid reserve 33.56g NaOH/100g
Melting point/freezing point Not available.
Initial boiling point and boiling Not available.
range
Pour point Not available.
Specific gravity Not available.
Partition coefficient Not available.
(n-octanol/water)
Flash point Not available.
Evaporation rate Not available.
Flammability (solid, gas) Not applicable.
Upper/lower flammability or explosive limits
Flammability limit - lower Not available.
(%)
Flammability limit - upper Not available.
(%)
Explosive limit - lower (%) Not available.
Explosive limit - upper (%) Not available.
Vapor pressure Not available.
Vapor density Not available.
Relative density Not available.
Solubility(ies) Not available.
Auto-ignition temperature Not available.
Decomposition temperature Not available.
Viscosity Not available.
 
  10. Stability and reactivity
Reactivity This product may react with reducing agents. May react with strong bases or oxidizing agents.
Possibility of hazardous Hazardous polymerization does not occur.
reactions
Chemical stability Stable under recommended storage conditions.
Conditions to avoid Do not mix with other chemicals.
Incompatible materials Caustics. Oxidizers. Bases. Reducing agents.
Hazardous decomposition May include and are not limited to: Ammonia. Oxides of carbon. Oxides of nitrogen. Oxides of
products sulfur.
 
  11. Toxicological information
Routes of exposure Inhalation. Ingestion. Skin contact. Eye contact.
Information on likely routes of exposure
Ingestion Causes digestive tract burns.
Inhalation May cause irritation to the respiratory system.
Skin contact Causes severe skin burns.
Eye contact Causes serious eye damage.
 
Symptoms related to the Burning pain and severe corrosive skin damage. Causes serious eye damage. Symptoms may
physical, chemical and include stinging, tearing, redness, swelling, and blurred vision. Permanent eye damage including
toxicological characteristics blindness could result.
Information on toxicological effects
Acute toxicity
 
#24470 Page: 4 of 8 Issue date 07-November-2019
 
Components Species Test Results
Citric Acid (CAS 77-92-9)
Acute
Dermal
LD50 

Rat > 2000 mg/kg, 24 Hours, ECHA

Inhalation
LC50 Not available
 
Oral
LD50 Mouse 5400 mg/kg, ECHA
   
Rat 11700 mg/kg, ECHA
Silicic acid, aluminum sodium salt (CAS 1344-00-9)
Acute
Dermal
LD50 Rabbit > 5000 mg/kg, 24 Hours, ECHA
 
Inhalation
LC50 Rat > 58.8 mg/L, 4 Hours, ECHA
 
> 2.1 mg/L, 4 Hours, ECHA
 
> 0.7 mg/L, 4 Hours, ECHA
Oral
LD50 Rat > 10000 mg/kg, ECHA
 
> 5000 mg/kg, ECHA
Sulfamic acid (CAS 5329-14-6)
Acute
Inhalation
LC50 Not available
Oral
LD50 Rat 2140 mg/kg, ECHA
   
Skin corrosion/irritation Causes severe skin burns and eye damage.
Exposure minutes Not available.
Erythema value Not available.
Oedema value Not available.
Serious eye damage/eye Causes serious eye damage.
irritation
Corneal opacity value Not available.
Iris lesion value Not available.
Conjunctival reddening Not available.
value
Conjunctival oedema value Not available.
Recover days Not available.
Respiratory or skin sensitization
Canada - Alberta OELs: Irritant
Silicic acid, aluminum sodium salt (CAS 1344-00-9) Irritant
Respiratory sensitization Not available.
Skin sensitization This product is not expected to cause skin sensitization.
Mutagenicity No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.
Carcinogenicity Not classified or listed by IARC, NTP, OSHA and ACGIH.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)
Not listed.
Reproductive toxicity This product is not expected to cause reproductive or developmental effects.
Teratogenicity Non-hazardous by WHMIS/OSHA criteria.
Specific target organ toxicity - Not classified.
single exposure
Specific target organ toxicity - Not classified.
repeated
  exposure
#24470 Page: 5 of 8 Issue date 07-November-2019
Aspiration hazard Not available.
Chronic effects Prolonged inhalation may be harmful.
 
  12. Ecological information
Ecotoxicity
 

See below
Ecotoxicological data
Components
  Species Test Results
Citric Acid (CAS 77-92-9)
Acute
Crustacea EC50 Daphnia magna 120 mg/L, 72 hr
 
Aquatic
Acute
Fish LC50 Bluegill (Lepomis macrochirus) 1516 mg/L, 96 hr
Silicic acid, aluminum sodium salt (CAS 1344-00-9)
Crustacea EC50 Daphnia 1400 mg/L, 48 Hours
 
Aquatic
Fish LC50 Guppy (Poecilia reticulata) 1800 - 3200 mg/L, 96 hours
 
Sulfamic acid (CAS 5329-14-6)
Aquatic
Fish LC50 Fathead minnow (Pimephales promelas) 14.2 mg/L, 96 hours
 
Persistence and degradability No data is available on the degradability of this product.
Bioaccumulative potential No data available.
Mobility in soil No data available.
Mobility in general Not available.
Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.
 
  13. Disposal considerations
Disposal instructions Review federal, state/provincial, and local government requirements prior to disposal. Collect and
reclaim or dispose in sealed containers at licensed waste disposal site. Do not allow this material
to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical
or used container.
Local disposal regulations Dispose in accordance with all applicable regulations.
Hazardous waste code The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Waste from residues / unused Dispose of in accordance with local regulations. Empty containers or liners may retain some
products product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Contaminated packaging Empty containers should be taken to an approved waste handling site for recycling or disposal.
Since emptied containers may retain product residue, follow label warnings even after container is
emptied.
 
  14. Transport information
Transport of Dangerous Goods Classification Method: Classified as per Part 2, Sections 2.1 – 2.8 of the Transportation of
(TDG) Proof of Classification Dangerous Goods Regulations. If applicable, the technical name and the classification of the
product will appear below.
U.S. Department of Transportation (DOT)
Basic shipping requirements:
UN number UN1759
Proper shipping name Corrosive solids, n.o.s.
Technical name Sulfamic acid
Hazard class 8
Subsidiary hazard class Limited Quantity - US
Packing group III
Special provisions 128, IB8, IP3, T1, TP33
Packaging exceptions <11 lbs - Limited Quantity
Packaging non bulk 213
Packaging bulk 240

 
#24470 Page: 6 of 8 Issue date 07-November-2019
Transportation of Dangerous Goods (TDG - Canada)
Basic shipping requirements:
UN number UN1759
Proper shipping name CORROSIVE SOLID, N.O.S.
Technical name
 
Sulfamic acid
Hazard class 8
Subsidiary hazard class Limited Quantity - Canada
Packing group III
Special provisions 16
Packaging exceptions < 5kg - Limited Quantity
DOT

TDG

 
  15. Regulatory information
Canadian federal regulations This product has been classified in accordance with the hazard criteria of the HPR and the SDS
contains all the information required by the HPR.
Export Control List (CEPA 1999, Schedule 3)
Not listed.
Greenhouse Gases
Not listed.
Precursor Control Regulations
Not regulated.
WHMIS 2015 Exemptions Not applicable
US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
CERCLA Hazardous Substance List (40 CFR 302.4)
Not listed.
SARA 304 Emergency release notification
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)
Not listed.
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Hazard categories Immediate Hazard - Yes
Delayed Hazard - No
Fire Hazard - No
Pressure Hazard - No
Reactivity Hazard - No
SARA 302 Extremely No
hazardous substance
SARA 311/312 Hazardous Yes
chemical

 
#24470 Page: 7 of 8 Issue date 07-November-2019
 SARA 313 (TRI reporting)
Not regulated.

Other federal regulations

Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
 

Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
US state regulations See below
US - California Hazardous Substances (Director's): Listed substance
Silicic acid, aluminum sodium salt (CAS 1344-00-9) Listed.
US - Minnesota Haz Subs: Listed substance
Silicic acid, aluminum sodium salt (CAS 1344-00-9) Listed.
US - Texas Effects Screening Levels: Listed substance
Citric Acid (CAS 77-92-9) Listed.
Silicic acid, aluminum sodium salt (CAS 1344-00-9) Listed.
Sulfamic acid (CAS 5329-14-6) Listed.
US. New Jersey Worker and Community Right-to-Know Act
Sulfamic acid (CAS 5329-14-6)
US. Pennsylvania Worker and Community Right-to-Know Law
Silicic acid, aluminum sodium salt (CAS 1344-00-9)
US. California Proposition 65
California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain
any chemicals currently listed as carcinogens or reproductive toxins.
Inventory status
Country(s) or region Inventory name On inventory (yes/no)*
Canada Domestic Substances List (DSL) No
Canada Non-Domestic Substances List (NDSL) Yes
United States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory Yes
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
 
  16. Other information

LEGEND HEALTH / 3
 
0
Severe 4 FLAMMABILITY 0
Serious 3 3 0
Moderate 2 PHYSICAL HAZARD 0
Slight 1 PERSONAL
Minimal 0 X
PROTECTION

Disclaimer The data contained in this material safety data sheet was obtained from sources that were
technically accurate, reliable, and state of the art when this document was prepared. If data was
unavailable to complete certain sections, the absence of that data is identified in this document.
Because the supplier cannot know the exact circumstances during actual use of this product, other
hazards, exposure scenarios, disposal considerations, and regulations may apply and it is the
responsibility of the user to read and understand the product label and this document before use.
Do not use the product for purposes other than those stated in Section 1.
Issue date 07-November-2019
Version # 03
Effective date 07-November-2019
Prepared by Dell Tech Laboratories Ltd. Phone: (519) 858-5021
Other information For an updated SDS, please contact the supplier/manufacturer listed on the first page of the
document.

Redbook revision # 3, 10/28/19

 
#24470 Page: 8 of 8 Issue date 07-November-2019