20J-S100/100S

CJ20S10/21MJ50

SERVICE MANUAL S77B620J-S100

COLOR TELEVISION
Chassis No. SN-70
20J-S100/S100S
POWER – VOL + ? CH > VIDEO IN L- AUDI
O -R
MTS STEREO

CJ20S10
MODELS 21MJ50
In the interests of user-safety (Required by safety regulations in some countries ) the set should be
restored to its original condition and only parts identical to those specified should be used.

ELECTRICAL SPECIFICATIONS
POWER INPUT ........................... 120 V AC 60 Hz SPEAKER
POWER RATING ........................................... 93W SIZE ................................................ 8cm(Round)
PICTURE SIZE ..................... 1240cm2(192sq inch) VOICE COIL IMPEDANCE ....... 8ohm at 400 Hz
CONVERGENCE .................................... Magnetic ANTENNA INPUT IMPEDANCE
SWEEP DEFLECTION ............................ Magnetic VHF/UHF ............................ 75 ohm Unbalanced
FOCUS ....................... Hi-Bi-Potential Electrostatic TUNING RANGES
INTERMEDIATE FREQUENCIES VHF-Channels ....................................... 2thru 13
Picture IF Carrier Frequency ............. 45.75 MHz UHF-Channels .................................... 14thru 69
Sound IF Carrier Frequency .............. 41.25 MHz CATV Channels ................................... 1thru 125
Color Sub-Carrier Frequency ............ 42.17 MHz USA: (EIA, Channel Plan)
(Nominal)
AUDIO POWER Specifications are subject to change without prior
OUTPUT RATING 1.3+1.3W (at 10% distortion & notice.
dual ch operate)
CONTENTS
Page
» ELECTRICAL SPECIFICATIONS ............................................................................................. 1
» IMPORTANT SERVICE SAFETY PRECAUTION .................................................................... 2
» LOCATION OF USER'S CONTROL ......................................................................................... 6
» INSTALLATION AND SERVICE INSTRUCTIONS .................................................................... 7
» CHASSIS LAYOUT ................................................................................................................ 13
» BLOCK DIAGRAM ................................................................................................................. 14
» SCHEMATIC DIAGRAMS ...................................................................................................... 15
» PRINTED WIRING BOARD ASSEMBLIES ............................................................................ 21
» REPLACEMENT PARTS LIST ............................................................................................... 29
» PACKING OF THE SET ......................................................................................................... 37

SHARP ELECTRONICS CORPORATION

Service Headquarters: Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP ELECTRONICS OF CANADA LTD.
335 Britannia Road East Mississauga, Ontario L4Z 1W9 Canada
SHARP CORPORATION
1
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

IMPORTANT SERVICE SAFETY PRECAUTION

Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and servicing guidelines which follow:

WARNING X-RADIATION AND HIGH VOLTAGE

1. For continued safety, no modification of any circuit LIMITS
should be attempted. 1. Be sure all service personnel are aware of the
2. Disconnect AC power before servicing. procedures and instructions covering X-radiation. The
3. Semiconductor heat sinks are potential shock only potential source of X-ray in current solid state
hazards when the chassis is operating. TV receivers is the picture tube. However, the picture
4. The chassis in this receiver has two ground systems tube does not emit measurable X-Ray radiation if the
which are separated by insulation material. The non- high
isolated (hot) ground system is for the B+ voltage voltage is as specified in the "High Voltage Check"
regulator circuit and the horizontal output circuit.The instructions.
isolated ground system is for the low B+ DC voltages It is only when high voltage is excessive that X-
and the secondary circuit of the high voltage radiation is capable of penetrating the shell of the
transformer. picture tube including the lead in glass material. The
To prevent electrical shock use an isolation important precaution is to keep the high voltage below
transformer between the line cord and power the maximum level specified.
receptacle, when servicing this chassis. 2. It is essential that service personal have available at
all times an accurate high voltage meter.
CAUTION: FOR CONTINUED The calibration of this meter should be checked
PROTECTION AGAINST A periodically.
RISKOF FIRE, REPLACE 3. High voltage should always be kept at the rated value
4A 125V ONLY WITH SAME TYPE 4A- −no higher. Operation at higher voltages may cause
125V FUSE. a failure of the picture tube or high voltage circuitry
SERVICING OF HIGH VOLTAGE SYSTEM and; also under certain conditions, may produce
radiation that exceeds specifications.
AND PICTURE TUBE 4. When the high voltage regulator is operating properly
When servicing the high voltage system, re- there is no possibility of an X-radiation problem. Every
move the static charge by connecting a 10k time a color chassis is serviced, the brightness
should be tested while monitoring the high voltage
ohm resistor in series with an insulated wire with a meter to be certain that the high voltage does
(such as a test probe) between the picture not exceed the specified value and that it is regulating
tube ground and the anode lead. (AC line correctly.
cord should be disconnected from AC out- 5. Do not use a picture tube other than that specified or
let.) make unrecommended circuit modifications to the
high voltage circuitry.
1. Picture tube in this receiver employs integral 6. When trouble shooting and taking test measurements
implosion protection. on a receiver with excessive high voltage, avoid being
2. Replace with tube of the same type number for unnecessarily close to the receiver.
continued safety. Do not operate the receiver longer than is necessary
3. Do not lift picture tube by the neck. to locate the cause of excessive voltage.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.

2
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

IMPORTANT SERVICE SAFETY PRECAUTION

(Continued)

BEFORE RETURNING RECEIVER » Connect the resistor connection to all exposed metal
parts having a return to the chassis
(Fire & Shock Hazard) (antenna, metal cabinet, screw heads, knobs and
Before returning the receiver to the user, perform control shafts, escutcheon, etc.) and measure the
the following safety checks. AC voltage drop across the resistor.
AII check must be repeated with the AC line cord
1. Inspect all lead dress to make certain that leads are plug connection reversed. (IF necessary, a non-
not pinched or that hardware is not lodged between polarized adapter plug must be used only for the
the chassis and other metal parts in the receiver. purpose of completing these check.)
2. Inspect all protective devices such as non-metallic Any current measured must not exceed 0.5 milliamp.
control knobs, insulating materials, cabinet backs, Any measurements not within the limits outlined
adjustment and compartment covers or shields, above are indicative of a potential shock hazard and
isolation resistor-capacity networks, mechanical corrective action must be taken before returning the
insulators, etc. instrument to the customer.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
» Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
» Using to clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series AC
with all exposed metal cabinet parts and a known VOLTMETER
earth ground, such as electrical conduit or electrical
ground connected to earth ground. 1.5k ohm
» Use an AC voltmeter having with 5000 ohm per volt, 10W
or higher, sensitivity to measure the AC voltage drop
across the resistor.

0.15µF
TEST PROBE

TO EXPOSED CONNECT TO
METAL PARTS KNOWN EARTH
GROUND

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212

SAFETY NOTICE
Many electrical and mechanical parts in television For continued protection, replacement parts must be
receivers have special safety-related characteristics. identical to those used in the original circuit.The use of
These characteristics are often not evident from visual substitute replacement parts which do not have the same
inspection, nor can protection afforded by them be safety characteristics as the factory recommended
necessarily increased by using replacement components replacement parts shown in this service manual, may
rated for higher voltage, wattage, etc. create shock, fire, X-radiation or other hazards.
Replacement parts which have special safety
characteristics are identified in this manual; electrical
components having such features are identified by
" å " and shaded areas in the Replacement Parts Lists
and Schematic Diagrams.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212

3
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

PRECAUTIONS A PRENDRE LORS DE LA REPARATION

Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.

AVERTISSEMENT LIMITES DES RADIATIONS X ET DE LA

1. N'entreprendre aucune modification de tout circuit. HAUTE TENSION
C'est dangereux. 1. Tout le personnel réparateur doit être instruit des
2. Débrancher le récepteur avant toute réparation. instructions et procédés relatifs aux radiations X.
3. Les déversoirs thermiques à semi-conducteurs Le tube-image, seule source de rayons X dons les
peuvent présenter un danger de choc électrique téleviseurs transistorisés, n'émet pourtant pas de
lorsque le réceqteur est en marche. rayons mesurables si la haute tension est maintenue
4. Le châssis de ce récepteur possède deux systèmes à un niveau préconisé dans la section "Vérification
de masse qui sont séparées par du matériel de la haute tension".
d'isolation. Le système de masse non-isolée (sous C'est seulement quand la haute tension est excessive
tension) est pour le circuit du régulateur de tension que les rayons X peuvent entrer dans l'enveloppe
+ B et le circuit de sortie horizontale. Le système de du tube-image y compris le conducteur de verre. Il
masse isolée est pour les tensions DC + B basses et est important de maintenir la haute tension en-
le circuit secondaire du transformateur haute tension. dessous du niveau spécifié.
Pour éviter tout risque d'électrocution lors de 2. Il est essentiel que le réparateur ait sous la main un
l'entretien de ce châssis, utiliser un transformateur voltmètre à haute tension qui doit être périodiquement
d'isolation entre le cordon de ligne et la prise de étalonné.
courant. 3. La haute tension doit toujours être maintenue à la
valeur de régime -et pas plus haute. L'opération à
PRECAUTION: POUR LA des tensions plus élevées peut entraîner une panne
PROTECTION CONTINUE du tube-image ou du circuit à haute tension et, dans
CONTRE LES RISQUES certaines conditions, peut entraîner une radiation
4A 125V D'INCENDIE, REMPLACER LE dépassant les niveaux préscrits.
FUSIBLE PAR UN FUSIBLE DE 4. Quand le régulateur à haute tension fonctionne
MEME TYPE 4A-125V. correctement, il n'y a aucun problème de radiation
X. Chaque fois qu'un châssis couleurs est réparé, la
REPARATION DU SYSTEME A HAUTE TEN- luminosité doit être examinée bout en contrôlant la
haute tension à l'aide d'un voltmètre pour s'assurer
SION ET DU TUBE-IMAGE que la haute tension ne dépasse pas la valeur
Lors de la réparation de ce systéme, spécifiée et qu'elle soit correctement réglée.
supprimer la charge statique en branchant 5. Ne pas utiliser un tube-image autre que celui spécifié
et ne pas effectuer de modifications déconseillées
une résistance de 10 kΩ en série avec un fil du circuit à haute tension.
isolé (comme une sonde d'essai) entre la 6. Lors de la recherche des pannes et des mesures
mise à la terre du tube-image et le fil d'essai sur un récepteur qui présente une haute
d'anodel. (Le corden d'alimentation doit être tension excessive, éviter de s'approcher inutilement
retiré de la prise murale.) du récepteur.
Ne pas faire fonctionner le récepteur plus longtemps
1. Le tube image dans ce récepteur emploie une que nécessaire pour localiser la cause de la tension
protection intégrée contre l'implosion. excessive.
2. Par mesure de sécurité, changer le tube-image pour
un tube du même numéro de type.
3. Ne pas lever le tube-image par son col.
4. Ne manipuler le tube-image qu'en porant des lunettes
incassables et qu'après avoir déchargé totalement
la haute tension.

4
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

PRECAUTIONS A PRENDRE LORS DE LA REPARATION

(Suite)

VERIFICATIONS CONTRE L'INCEN-DIE ET » Toucher avec la sonde d'essai les pièces métalliques
LE CHOC ELECTRIQUE exposées qui présentent une voie de retour au
châssis (antenne, coffret métallique, tête des vis,
Avant de rendre le récepteur à l'utilisateur, effectuer arbres de commande et des boutons, écusson, etc.)
les vérifications suivantes. et mesurer la chute de tension CA en-travers de la
résistance. Toutes les vérifications doivent être
1. Inspecter tous les faisceaux de câbles pour s'assurer refaites après avoir inversé la fiche du cordon
que les fils ne soient pas pincés ou qu'un outil ne d'alimentation. (Si nécessaire, une prise d'adpatation
soit pas placé entre le châssis et les autres pièces non polarisée peut être utilisée dans le but de
métalliques du récepteur. terminer ces vérifications.)
2. Inspecter tous les dispositifs de protection comme Tous les courants mesurés ne doivent pas dépasser
les boutons de commande non-métalliques, les 0,5 mA.
isolants, le dos du coffret, les couvercles ou blindages Dans le cas contraire, il y a une possibilité de choc
de réglage et de compartiment, les réseaux de électrique qui doit être supprimée avant de rendre le
résistance-capacité, les isolateurs mécaniques, etc. récepteur au client.
3. S'assurer qu'il n'y ait pas de danger d'électrocution
en vérifiant la fuite de courant, de la facon suivante:
» Brancher le cordon d'alimentation directem-ent à une
prise de courant de 120V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
» A l'aide de deux fils à pinces, brancher une résistance
de 1,5 kΩ 10 watts en parallèle avec un condensateur Voltmètre
AC CA
de 0,15µF en série avec toutes les pièces métalliques VOLTMETER
exposées du coffret et une terre connue comme une
1.5k ohm
conduite électrique ou une prise de terre branchée à 10W
la terre.
» Utiliser un voltmètre CA d'une sensibilité d'au moins
5000Ω/V pour mesurer la chute de tension en travers
de la résistance.
0.15µF
SONDE D'ESSAI
TEST PROBE

AUX PIECES BRANCHER A TO

UNE
TO EXPOSED CONNECT
METALLIQUES TERRE CONNUE
METAL PARTS KNOWN EARTH
EXPOSEES
GROUND

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212

AVIS POUR LA SECURITE

De nombreuses pièces, électriques et mécaniques, dans identifiées par la marque " å " et hachurées dans la
les téléviseurs présentent des caractéristiques spéciales liste des pièces de remplacement et les diagrammes
relatives à la sécurité, qui ne sont souvent pas évidentes schématiques.
à vue. Le degré de protection ne peut pas être Pour assurer la protection, ces pièces doivent être
nécessairement augmentée en utilisant des pièces de identiques à celles utilisées dans le circuit d'origine.
remplacement étalonnées pour haute tension, L'utilisation de pièces qui n'ont pas les mêmes
puissance, etc. caractéristiques que les pièces recommandées par
Les pièces de remplacement qui présentent ces l'usine, indiquées dans ce manuel, peut provoquer des
caractéristiques sont identifiées dans ce manuel; les électrocutions, incendies, radiations X ou autres
pièces électriques qui présentent ces particularités sont accidents.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212

5
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

LOCATION OF USER'S CONTROL

MTS STEREO
-R
– VOL + ? CH> VIDEO IN L- AUDIO
POWER

VIDEO/AUDIO IN TERMINALS
(25J-S100: VIDEO/AUDIO terminals are
also provided on the rear.)

(Model : 20J-S100)

SENSOR AREA FOR

REMOTE CONTROL POWER – VOL + CH

POWER
Press → ON. VOLUME UP/DOWN CHANNEL UP/DOWN
Press again → OFF. (+) Increases sound. (8) Selects next higher channel.
(–) Decreases sound. (9) Selects next lower channel.

(Model : 25J-S100)
POWER – VOL + CH

POWER

Infrared Transmitter Window

INPUT
(20J-S100)
Press n Switch to external video
POWER input mode.
Press n On. Press again n Switch to TV mode.
Press again n Off. (25J-S100)
Press n Switch to external video
FLASHBACK INPUT 1 mode.
Returns to previously viewed Press again n Switch to external
channel. video INPUT 2 mode.
Press 3 times n Switch back to the
VOLUME UP/DOWN original TV mode.
(+) Increases sound. See page 17.
(–) Decreases sound.
• In menu mode, changes or Direct Access
selects the TV adjustments. Accesses any channel by the
keypad.
MUTE
CHANNEL UP/DOWN
Press n Mutes sound.
( 8 ) Selects next higher channel.
Press again n Restores sound. ( 9 ) Selects next lower channel.
• CLOSED CAPTION appears • See pages 15, 16 for channel
when sound is muted. presetting.
• Moves the “ ” mark of the
DISPLAY MENU screen.
Press n Displays receiving
channel for 4 seconds. MENU
Press again n Removes display. Press n Accesses MAIN MENU.
• Temporarily displays receiving TV Press again n Exits MAIN MENU.
channel when in Closed Caption
mode.

6
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

INSTALLATION AND SERVICE INSTRUCTIONS

Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdriver or TV alignment tools.
(2) Before performing adjustment, TV set must be on at least 15 minutes.

CIRCUIT PROTECTION HIGH VOLTAGE CHECK

The receiver is protected by a 4.0A fuse (F701), High voltage is not adjustable but must be checked
mounted on PWB-A, wired into one side of the AC to verify that the receiver is operating within safe
line input. and efficient design limitations as specified checks
should be as follows:
X-RADIATION PROTECTOR CIRCUIT
TEST 1. Connect an accurate high voltage meter between
ground and anode of picture tube.
1. After service has been performed on the 2. Operate receiver for at least 15 minutes at 120V AC
horizontal deflection system, high voltage line voltage, with strong air signal or properly tuned
system, B + system, test the X-Radiation in test signal.
protection circuit to ascertain proper operation 3. Set service mode on (See next page.),Service
as follows: No.S19 and Bus data "01" (Y-mute on).
4. The voltage should be approximately 26.5kV (at zero
1) Apply 120V AC using a variac transformer for beam).
accurate input voltage. If a correct reading cannot be obtained, check circuitry
2) Allow for warm up and adjust all customer controls for malfunctioning components. After the voltage
for normal picture and sound. test,make Y-mute off (normal mode).
3) Select a local channel.
4) Connect a digital voltmeter to TP653 and make sure
that the voltmeter reads 21.5±1.5V.
5) Apply external 26.8V DC at TP653 by using an
external DC supply, TV must be shut off.
6) To reset the protector, unplug the AC cord and make
a short circuit between TP651 and TP652.Now make
sure that normal picture appears on the screen.
7) If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.

7
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

For adjustments of this model, the bus data is convered to various analog signals by the D-A converter circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage.
Follow the steps below whenever service adjustment is required. See Figure "B" to determine if service adjust-
ments are required.

1. Service mode - To enter the service mode .

Before putting unit into the service mode, check, that
While Pressing the Vol-up and Ch- up buttons at once,
customer adjustments are in the normal mode. use
plug the AC cord into a wall socket.Now the TV set is
the reset function in the video adjust menu to ensure
switched on and enters the service mode.
customer controls are in their
To exit the service mode, shut the television off by
2. Service number selection
pressing the power button.
Once in the service mode, press the channel up or
channel down button on the remote transmitter or at
the set. the service adjustment number will vary in
increments of one, from "S01" to M05.
Select the item you wish to adjust.

3. Data number selection

Press the volume up or down button to adjust the
data number.
Vertical-size adjustment
1. Have unit receive a good local channel.
2. Enter the service mode and select service adjustment
"S09".
3. While observing the top and bottom of the screen,
DATA NUMBER adjust "S09" data value to proper vertical size .
SERVICE ADJUSTMENT
NUMBER CHANNEL
Vertical phase adjustment
1. Enter the service mode and select service adjustment
S01 55 02 "S06".
2. Adjust data value to "00"~"03" so that picture is
approximate center.
Note: This must be set "00"~"03" when adjust another
data retrace line will be appear.

"Horizontal position adjustment

1. Have unit receive a good local channel.
2. Enter the service mode and select service adjustment
S01 D:00 "S07".
3. Adjust "S07" data value so that picture is centered.

Figure B.

8
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

SERVICE DATA
ADJUSTMENT ITEM ADJUSTMENT CONTENTS
NUMBER INITIAL VALUE RANGE
S01 PICTURE 55 00-7F
S02 TINT 46 00-7F
S03 COLOR 32 00-7F
S04 BRIGHTNESS 40 00-7F
S05 SHARPNESS 28 00-3F Must be set to “24”
S06 VERTICAL PHASE 00 00-07
S07 HORIZONTAL PHASE 12 00-1F
S08 RF-AGC 2A 00-3F
S09 VERTICAL AMP 20 00-3F
S10 VCO 2C 00-7F
S11 R CUT-OFF 00 00-FF
S12 G CUT -OFF 00 00-FF
S13 B CUT-OFF 00 00-FF
S14 G GAIN 7F 00-FF
S15 B GAIN 7F 00-FF
S16 TRAP(3.58MHz) 00 00 or 01 Must be set to “00”
S17 BALANCE 20 00-3F Must be set to “20”
S18 C.C.POSITION 18 00-7F
S19 Y-MUTE 00 00,01,03 00=NORMAL, 01=no “Y, 03=NO VERTICAL”
OP OPTION (Set to each mode ) 00-7E Must be set to “9”
M01 MTS LEVEL 0A 00-FF
M02 STEREO-VCO 20 00-3F
M03 FILTER 1C 00-3F
M04 LOW SEPARATION 20 00-3F
M05 HIGH SEPARATION 1B 00-3F

Table - A

Holding down both the CH UP/DOWN keys on the TV set at service mode for more then 2 seconds will automatically
write the above initial values into IC2101.

ADJUSTMENT
PART REPLACED NOTES
NECESSARY UNNECESSARY

IC2001 X Data is stored in IC2101.

X The adjustment is needed to compensate for

IC201
characteristics of parts including IC201.
Holding down both the CH UP/DOWN keys on the TV set
IC2101 X at service mode for more than 2 seconds will automatically
write the above initial values into IC2101.

X Adjust items related to picture tube only.

CRT

IC3001 X Adjust items related to MTS only (M01~M05).

Table - B

9
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

Ë adjustment
VCO Adjustment White balance adjustment
1. Connect a digital voltmeter between pin (44) of IC201 1. Have unit receive a good local channel.
and ground. 2. Enter the service mode. select service adjustment
2. Select a good local channel. "S03" and set to "00" ( minimum color). "S03" does
3. Enter the service mode. select adjustment "S10". not have to be adjusted if you selected a B/W picture
4. Adjust the data so that digital voltmeter shold read or monoscope pattern.
2.2V 3. Alternately adjust service adjustment data of "S14"
5. Adjustment is complete, remove the volt-meter, and "S15" untill a good grey scale with normal whites
return to "normal" mode. is obtained.
4. Select service adjustment "S03" and adjust data to
obtain normal color level.
RF AGC Adjustment
1. Have unit receive a good local channel. Sub-picture adjustment
2. Enter the service mode and select service adjustment
"S08". 1. Have unit receive a good local channel.
3. Set the data value to point where no noise or beat 2. Make sure the customer picture control is set to
appears. maximum.
4. Select another channel to confirm that no noise or 3. Enter the service mode and select service adjustment
beat appears. "S01".
NOTE 1: You will have to come out of the service 4. Adjust the data value to achieve normal contrast
mode to select another channel. range.
NOTE 2: Setting the data to "00" will pro-duce a black
raster. Sub-Tint Adjustment
1. Have unit receive a good local channel.
Screen adjustment 2. Set customer tint control to center of it's range.
3. Enter the service mode and select service adjustment
1. Connect a digital voltmeter between TP852 and "S02".
TP853 on the CRT socket PWB. 4. Adjust "S 02" data value to obtain normal flesh tones.
Note: These test points may not be provided.
Then connect the voltmeter to both ends of R852
located near Q852 on the foil side. Sub-color adjustment
2. Select a good local channel.
3. Enter the service mode and select service adjustment 1. Have unit receive a good local channel.
“S03” and set the data value to “00” to set the color 2. Make sure the customer color control is set to center
level to minimum.(Record original data code under position .
adjustment “S03” before changing) You may skip this 3. Enter the service mode and select service adjustment
step if you selected a B/W picture or monoscope "S03".
pattern. 4. Adjust "S03"data value to obtain normal color level.
4. Select service adjustment “S19” and adjust the data
value to “01” this turn off the luminance signal (Y- Sub-brightness adjustment
mute). 1. Have unit receive a good local channel.
5. Select service adjustment "S04" and adjust data 2. Make sure the customer brightness control is set to
value to obtain 0.17 volts on the digital voltmeter. center position.
6. Adjust the master screen cotrol untill raster darkens 3. Enter the service mode and select service adjustment
to the point where raster is barely seen. "S04".
7. Adjust service adjustments "S11" red,"S12" green 4. Adjust "S04"data value to obtain normal brightness
and "S13" blue to obtain a good grey scale with level.
normal whites at low brightness level.
8. Select service adjustment “S19” and reset data to
“00”.
Select service adjustment “S03” and reset data to
obtain normal color level.
9. Remove digital voltmeter.
Reset master screen cotrol to obtain normal
brightness range.

10
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

Caption position adjustment (horizontal) MTS level adjustment

1. Have unit receive a good local channel. 1. Feed the following monaural signal to pin (14) of
2. Enter the service mode and select service adjustment IC3001.
"S18". Monaural signal: 300Hz,245mVrms
3. A black text box appears on the screen (see Figure 2. Connect the rms voltmeter to pin (39) of IC3001.
C). 3. Enter the service mode and select the service
4. Adjust "S18" data value so that text box is positioned adjustment "M01".
in the center of the screen. 4. Adjust the data so that the rms voltmeter should take
the reading below. Spec:490 ±10mVrms.

Stereo VCO adjustment

1. Keep the unit in no-signal state.
2. Connect the frequency counter to pin (39) of IC3001.
3. Connect a capacitor (100µ F, 50V) in between positive
(+) side of C3005 and ground.
4. Enter the service mode and select the service
adjustment "M02".
5. Adjust the data so that frequency counter should take
Figure C. the reading below.Spec:62.94 ±0.75kHz

Filter adjustment
3.58MHz trap adjustment
1. Feed the following stereo pilot signal to pin (14) of
1. Have unit receive a good local channel.
IC3001.Stereo pilot signal:9.4kHz,600mVrms.
2. Enter the service mode and select service adjustment
2. Enter the service mode and select the service
"S16" .
adjustment "M03".
3. This is a two position adjustment, "00"is ON , "01" is
3. Adjust the data at the point where "OK" appears on
OFF.
the screen. The "OK" represents the approximate
4. Adjust data value to "00" for normal viewing.
center of the adjustable range of the data.
Sharpness and Audio balance adjust- Separation Adjustment
ments
1. Connect the rms voltmeter to pin (39) of IC3001.
1. Have unit receive a good local channel. 2. Receive the following composite stereo signal 1.
2. Enter the service mode and select "S05" for Composite stereo signal: 30% modulation, left
sharpness and "S17" for balance. channel only, noise reduction on, 300Hz.
• Sharpness adjustments 3. Enter the service mode and select the service
3. Adjust data value to "24" (center of data range) for adjustment "M04".
sharpness adjustment. 4. Adjust the data until the AC voltage reading of the
• Audio balance adjustments rms voltmeter is minimum.
4. Adjust data value to "20" (center of data range) for
Audio balance adjustment.
5. Receive the following composite stereo signal2.
Stereo signal :30% modulation , left channel only,
noise reduction on, 3kHz.
6. Enter the service mode and select the service
adjustment "M05".
7. Adjust the data until theAC voltage reading of the
rms voltmeter is minimum.
8. Take the above steps 1 thru 8 again for fine
adjustment.

11
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

DESCRIPTION OF SCHEMATIC DIAGRAM

NOTE: WAVEFORM MEASUREMENT CONDITIONS:
1. The unit of resistance "ohm" is omitted (K:1000 1. Photographs taken on a standard gated color bar
ohms, M:1 Meg ohm). signal, the tint setting adjusted for proper color. The
2. All resistors are 1/8 watt, unless otherwise noted. wave shapes at the red, green and blue cathodes of
3. All capacitors are µ F, unless otherwise noted P: the picture tube depend on the tint, color level and
µµ F. picture control.
4. (G) indicates ±2% tolerance may be used. 2. indicates waveform check points (See chart,
5. indecates line isolated ground. waveforms are measured from point indicated to
chassis ground.)
6. indecates hot ground.
å AND SHADED ( ) COMPONENTS
VOLTAGE MEASUREMENT CONDITIONS:
= SAFETY RELATED PARTS.
1. All DC voltages are measured with DVM connected
ç MARK= X-RAY RELATED PARTS.
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for
DRGANNES MARQUES å ET HACHRES ( ):
normal picture unless otherwise indicated.
PIECES RELATIVES A LA SECURITE.
2. All voltages measured with 1000µ V B & W or Color
MARQUE ç : PIECS RELATIVE AUX RAYONS X.
signal.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.

WAVE FORMS

12
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

CHASSIS LAYOUT
H

1 2 3 4 5 6

13
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

BLOCK DIAGRAM
H

1 2 3 4 5 6

14
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S 20J-S100/100S
CJ20S10/21MJ50 CJ20S10/21MJ50

SCHEMATIC DIAGRAM :CRT Unit

H

1 2 3 4 5 6 7 8 9 10 11 12

15 16

Downloaded from www.Manualslib.com manuals search engine

 20J-S100/100S 20J-S100/100S
CJ20S10/21MJ50 CJ20S10/21MJ50

SCHEMATIC DIAGRAM: MAIN Unit: 20J-S100, 21MJ50, CJ20S10

H

IX 2701C E N 1 – 20J S 100/C J 20S 10

IX 2573C E – 21MJ 50

L701
*20J-S100/21M50
C I LF 0235C E
C I LF 0087C E
*CC JI LF 0029PE
20S10

A C I LF 0090C E

1 2 3 4 5 6 7 8 9 10 11 12

17 18

Downloaded from www.Manualslib.com manuals search engine

 20J-S100/100S 20J-S100/100S
CJ20S10/21MJ50 CJ20S10/21MJ50

SCHEMATIC DIAGRAM: MAIN Unit: 20J-S100S

H

1 2 3 4 5 6 7 8 9 10 11 12

19 20

Downloaded from www.Manualslib.com manuals search engine

 20J-S100/100S 20J-S100/100S
CJ20S10/21MJ50 CJ20S10/21MJ50

PRINTED WIRING BOARD ASSEMBLIES: 20J-S100, 21MJ50, CJ20S10

H

F
PWB-B:CRT Unit (Wiring Side)

PWB-E:MTS Unit (Wiring Side)

B

PWB-A:MAIN Unit (Wiring Side)

1 2 3 4 5 6 7 8 9 10 11 12

21 22

Downloaded from www.Manualslib.com manuals search engine

 20J-S100/100S 20J-S100/100S
CJ20S10/21MJ50 CJ20S10/21MJ50

F
PWB-B:CRT Unit (Chip Parts Side)

PWB-E:MTS Unit (Chip Parts Side)

B

PWB-A:MAIN Unit (Chip Parts Side)

1 2 3 4 5 6 7 8 9 10 11 12

23 24

Downloaded from www.Manualslib.com manuals search engine

 20J-S100/100S 20J-S100/100S
CJ20S10/21MJ50 CJ20S10/21MJ50

PRINTED WIRING BOARD ASSEMBLIES: 20J-S100S

H

F
PWB-B:CRT Unit (Wiring Side)

PWB-E:MTS Unit (Wiring Side)

B

PWB-A:MAIN Unit (Wiring Side)

1 2 3 4 5 6 7 8 9 10 11 12

25 26

Downloaded from www.Manualslib.com manuals search engine

 20J-S100/100S 20J-S100/100S
CJ20S10/21MJ50 CJ20S10/21MJ50

F
PWB-B:CRT Unit (Chip Parts Side)

PWB-E:MTS Unit (Chip Parts Side)

B

PWB-A:MAIN Unit (Chip Parts Side)

1 2 3 4 5 6 7 8 9 10 11 12

27 28

Downloaded from www.Manualslib.com manuals search engine

 20J-S100/100S 20J-S100/100S
CJ20S10/21MJ50 CJ20S10/21MJ50

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PARTS LIST LISTE DES PIECES DUNTK9273WEV3/V6/V9 D752 RH-EX0019TAZZ J Zener Diode AB
PARTS REPLACEMENT CHANGE DES PIECES DUNTK9316WEV1 MAIN UNIT
D757 VHD1SS119//-1 J Diode AB
D758 RH-DX0131CEZZ J Diode AC
Replacement parts which have these special safety characteristics Les pi`eces de rechange qui pr élelesentent ces caract éleristiques
identified in this manual ; electrical components having such fea- sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les å Q602 VS2SD2095//1E J 2SD2095 AN D2001 VHD1SS119//-1 J Diode AB
tures are identified by å and shaded areas in the Replacement Parts pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep or VS2SD1555//1E AP D2060 RH-EX0298CEZZ J Zener Diode AA
Lists and Schematic Diagrams. The use of a substitute replacement éler élee par la marque å et sont hachur élees dans les listes de or VS2SD2499//1E —
part which dose no have the same safety characteristic as the fac- pi`eces et dans les diagrammes sch élematiques.
tory recommended replacement parts shown in this service manual La substitution d'une pi`ece de rechange par une autre qui ne pr
or VS2SD2586//1E AM PACKAGED CIRCUITS
may create shock, fire or other hazards. éLesente pas les m éoemes caract éLeristiques de s élecurit éle que Q603 VS2SC945AQ/-1 J 2SC945(AQ) AB å PR701 RMPTP0026CEZZ J Packaged Circuit AF
la pi`ece recommand élee parl'usine et dans ce manuel de service, or VS2SC1815YW-1 X801 RCRSB0001PEZZ R Crystal AL
"HOW TO ORDER REPLACEMENT PARTS"
peut provoquer une éLelectrocution, un incendie ou toutautre sinistre. or VS2SC3198-Y-1 or RCRSB0205CEZZ
To have your order filled promptly and correctly, please furnish the
following informations. "COMMENT COMMANDER LES PIECES DE RECHANGE" Q730 VS2SD667D//-1 J 2SD667(D) AE
Pour que votre commande soit rapidement et correctement remplie, å Q751 VS2SD667D//-1 J 2SD667(D) AE FILTERS
1. MODEL NUMBER 2. REF. NO. veuillez fournir les renseignements suivants. or VS2SC1983//-2 CF301 RFiLC0403CEZZ J Filter AE
3. PART NO. 4. DESCRIPTION Q752 VS2SC945AQ/-1 J 2SC945(AQ) AB or RFiLC0029TAZZ
1. NUMERO DU MODELE 2. NO. DE REF or VS2SC1815YW-1 CF302 RFiLC0404CEZZ J Filter AF
3. NO. DE PIECE 4. DESCRIPTION or VS2SC3198-Y-1 or RFiLC0029TAZZ J AD
in USA: Contact your nearest SHARP Parts Distributor to or-
der. For location of SHARP Parts Distributor, Please in CANADE: Contact SHARP Electronics of Conada Limited Q753 VS2SA1013//1E J 2SA1013 AD or RFiLC0007PEZZ R AF
call Toll-Free; 1-800-BE-SHARP Phone (416) 890-2100
Q2001 VS2SD601AR/-1 J 2SD601(AR) AC CF401 RFiLC0013CEZZ J Filter AE
MARK★: SPARE PARTS-DELIVERY SECTION ★MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE Q2002 VS2SD601AR/-1 J 2SD601(AR) AC or RFiLC0004PEZZ R AE
Q2060 VS2SD601AR/-1 J 2SD601(AR) AC CF631 RFiLA0034CEZZ J Filter AD
MARK ç : X- RAY RELATED PARTS ç MARQUE : PIECES RELATIVE AUX RAYONS X CF2040 RFiLC0121GEZZ J Filter AD
DIODES
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
You can substitute "VHD1SS119//-1" for "RH-DX0446CEZZ". COILS
D51 RH-EX0611GEZZ J Zener Diode AA L201 VP-XF1R2K0000 J Peaking 1.2µH AB
PICTURE TUBE DUNTK9273WEV3/V6/V9 D52 RH-EX0701GEZZ J Zener Diode AB L202 RCiLi0612CEZZ J If Coil AE
DUNTK9316WEV1 MAIN UNIT D53 RH-EX0611GEZZ J Zener Diode AA or RCiLi0588CEZZ
20J-S100/CJ20S10/21MJ50 TUNER D103 VHD1SS119//-1 J Diode AB L301 VP-XF8R2K0000 J Peaking 8.2µH AB
çå V101 VB51KZR50X/*S M CRT CC NOTE: THE PARTS HERES SHOWN ARE SUPPLIES AS AN D401 VHD1SS119//-1 J Diode AB L302 RCiLi0613CEZZ J If Coil AE
çå DY601 RCiLH0105MEZZ M DY AY ASSEMBLY INDEPENDETLY. D402 RH-EX0092CEZZ J Zener Diode AB or RCiLi0605CEZZ
å L702 RCiLG0017MEZZ M Degaussing Coil AM å TU51 VTUVTST6UF78/ J Tuner BD D454 RH-EX0103CEZZ J Zener Diode AB L401 VP-XF6R8K0000 J Peaking 6.8µH AB
MSPRT0002MEZZ M Spring for CRT AA D455 VHD1SS119//-1 J Diode AB L402 VP-XF3R3K0000 J Peaking 3.3µH AB
QEARC2002MEZZ M Grounding Strap AF INTEGRATED CIRCUITS D501 RH-DX0441CEZZ J Diode AC L403 VP-XF100K0000 J Peaking 10µH AB
PMAGF3003MEZZ M Magnet A'ssy — IC101 VHiKA78S05P-1 J KiA78S05P AD or RH-DX0110CEZZ J AB L404 VP-XF8R2K0000 J Peaking 8.2µH AB
PSPAG0012MEZZ M Wedge AA çå IC201 RH-iX2701CEN1 J TA1201CN AY å D502 RH-DX0131CEZZ J Diode AC L406 VP-XF680K0000 J Peaking 68µH AB
(20J-S100/100S/CJ20S10) D601 RH-DX0441CEZZ J Diode AC L409 VP-XF100K0000 J Peaking 10µH AB
20J-S100S çå IC201 RH-iX2573CEZZ J I. C.(21MJ50) BA or RH-DX0110CEZZ J AB å L701 RCiLF0029PEZZ R Coil —
çå V101 VB51KZE89X/1E M CRT — IC351 VHiTDA7233/-1 J TDA7233 AF D603 RH-DX0441CEZZ J Diode AC or RCiLi0235CEZZ (20J-S100/S100S/21MJ50)
çå DY601 RCiLH0107MEZZ M DY AZ IC501 VHiTA8403K/-1 J TA8403k AL or RH-DX0110CEZZ J AB or RCiLi0087CEZZ
å L702 RCiLG0017MEZZ M Degaussing Coil AM IC701 VHiSTR301301E J I.C. AP D604 VHD1SS119//1E J Diode AA å L701 RCiLF0090CEZZ J Coil (CJ20S10)
MSPRT0002MEZZ M Spring for CRT AA å IC751 VHiKA7809Pi-1 R KiA7809Pi AE or RH-DX0441CEZZ J AC L2040 RCiLB0131CEZZ J Oscillation Coil AE
QEARC2002MEZZ M Grounding Strap AF or VHiTA7809S/-1 or RH-DX0110CEZZ J AB SF201 RFiLC0405CEZZ J Filter AH
PMAGF3001MEZZ M Magnet A'ssy AG IC2001 RH-iX2946CEZZ J TMPA8701CKF108 AX D605 VHD1SS119//1E J Diode AA
PSPAG0012MEZZ M Wedge AA IC2040 VHiPST994C/-1 J PST994C AD or RH-DX0441CEZZ J AC TRANSFORMERS
IC2101 RH-iX2447CEN1 J ST24C01B6 AL or RH-DX0110CEZZ J AB å T601 RTRNZ0168CEZZ J Transformer AH
or RH-iX2448CEN1 D631 RH-EX0630GEZZ J Zener Diode AA çå T602 RTRNF0149PEZZ R H-Out —
D641 RH-EX0631GEZZ J Zener Diode AA å T701 RTRNP0518CEZZ J Power AN
PRINTED WIRING BOARDASSEMBLYS
TRANSISTORS çå D651 RH-DX0131CEZZ J Diode AC
(NOT REPLACEMENT ITEM)
You can substitute "VS2SD601AR/-1" for "VS2SC2462-C-1". çå D652 VHD1SS119//-1 J Diode AB CAPACITORS
PWB-A DUNTK9273WEV3 - Main Unit (20J-S100) — Q201 VS2SC2735//1E J 2SC2735 AC çå D653 RH-EX0091CEZZ J Zener Diode AB (EL: Electrolytic, M-Poly.: Metalized Polypro Film)
PWB-A DUNTK9273WEV6 - Main Unit (CJ20S10) — Q351 VS2SD601AR/-1 J 2SD601(AR) AC å D661 RH-DX0444CEZZ J Diode AH C51 VCEA0A1CW476M J 47 16V EL. AB
PWB-A DUNTK9273WEV9 - Main Unit (21MJ50) — Q401 VS2SD601AR/-1 J 2SD601(AR) AC å D701 RH-DX0154CEZZ J Diode AC C52 VCSATA1CE226K J 22 16V Tantalum AD
PWB-A DUNTK9316WEV1 - Main Unit (20J-S100S) — Q402 VS2SB709AR/-1 J 2SB709(AR) AC å D702 RH-DX0154CEZZ J Diode AC C53 VCEA0A1HW105M J 1.0 50V EL. AB
PWB-B DUNTK9274WEV3 - CRT Unit (20J-S100/ — Q403 VS2SD601AR/-1 J 2SD601(AR) AC å D703 RH-DX0154CEZZ J Diode AC C54 VCEA0A1HW225M J 2.2 50V EL. AB
CJ20S10/21MJ50) Q404 VS2SB709AR/-1 J 2SB709(AR) AC å D704 RH-DX0154CEZZ J Diode AC C55 VCEA0A1CW477M J 470 16V EL. AC
PWB-B DUNTK9317WEV1 - CRT Unit (20J-S100S) — Q451 VS2SB709AR/-1 J 2SB709(AR) AC D730 RH-EX0317CEZZ J Zener Diode AA C102 VCEAGA1CW108M J 1000 16V EL. AD
PWB-E DUNTK9275WEV5 - MTS Unit — Q601 VS2SC2655Y/-1 J 2SC2655(Y) AE å D751 RH-DX0417CEZZ J Diode AE C201 VCKYCY1HF103Z J 0.01 50V Ceramic AA
or RH-DX0200CEZZ J

29 30

Downloaded from www.Manualslib.com manuals search engine

 20J-S100/100S
CJ20S10/21MJ50

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9273WEV3/V6/V9 C552 VCEA0A1HW225M J 2.2 50V EL. AB

C604 VCEA0A1CW227M J 220 16V EL. AC
DUNTK9316WEV1 MAIN UNIT çå C608 VCFPPD3CA712H J 7100p 1.6kV M-Poly. AE
C202 VCKYPA1HF103Z J 0.01 50V Ceramic AA (20J-S100/21MJ50/CJ20S10)
C203 VCKYCY1HF103Z J 0.01 50V Ceramic AA çå C608 VCFPPD3CA742H J 7400p 1.6kV M-Poly. AF
C204 VCKYCY1HF103Z J 0.01 50V Ceramic AA (20J-S100S)
C205 VCEA0A1HW474M J 0.47 50V EL. AB C609 RC-QZA223TAYK J 0.022 50V Mylar AB
C206 VCEA0A1CW227M J 220 16V EL. AC C612 VCFPPJ2EB564J J 0.56 250V M-Poly. —
C207 VCKYCY1HF103Z J 0.01 50V Ceramic AA C631 VCEA0A1HW225M J 2.2 50V EL. AB
C208 VCEA0A1HW474M J 0.47 50V EL. AB C632 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C209 VCKYCY1HB222K J 2200p 50V Ceramic AA C633 VCEA0A1HW105M J 1.0 50V EL. AB
C210 VCKYCY1HB102K J 1000p 50V Ceramic AA C652 VCEA0A1HW475M J 4.7 50V EL. AB
C302 VCCCCY1HH330J J 33p 50V Ceramic AA C653 VCEA0A1CW106M J 10 16V EL. AB
C303 VCCCCY1HH390J J 39p 50V Ceramic AA C661 VCKYPA2HB152K J 1500p 500V Ceramic AA
C305 VCKYPA1HB151K J 150p 50V Ceramic AA C662 VCEA0A1CW477M J 470 16V EL. AC
C306 VCKYPA1HF103Z J 0.01 50V Ceramic AA å C701 RC-FZ004SGEZZ J 0.47 AC125V Plastic AE
C308 VCKYCY1HB102K J 1000p 50V Ceramic AA or RC-QZ005SCEZZ
C309 VCEA0A1CW227M J 220 16V EL. AC or RC-FZ002SCEZZ
C312 VCKYCY1HF103Z J 0.01 50V Ceramic AA or RC-FZ027CUMZZ
C313 VCEA0A1HW225M J 2.2 50V EL. AB or RC-FZ0279CEZZ
C351 VCKYCY1HB562K J 5600p 50V Ceramic AA or RC-FZ015SCEZZ
C352 VCEA0A1CW107M J 100 16V EL. AC C702 VCKYPB2HE103P J 0.01 500V Ceramic AB
C353 VCEA0A1CW337M J 330 16V EL. AC C703 VCKYPB2HE103P J 0.01 500V Ceramic AB
C354 RC-QZA104TAYK J 0.1 50V Mylar AB C704 VCKYPB2HE103P J 0.01 500V Ceramic AB
C355 VCEA0A1CW226M J 22 16V EL. AB å C705 RC-EZ0422CEZZ J 470 200V EL. AN
C361 VCEAGA1CW108M J 1000 16V EL. AD or RC-EZ0522CEZZ AN
C362 VCEA0A1CW476M J 47 16V EL. AB or RC-EZ0423CEZZ 620 200V EL.
C402 VCCCCY1HH331J J 330p 50V Ceramic AA or RC-EZ0523CEZZ 560 200V EL.
C403 VCCCCY1HH101J J 100p 50V Ceramic AA å C706 RC-KZ0311CEZZ J 0.0033 AC125V Ceramic AC
C405 VCEA0A1HW335M J 3.3 50V EL. AB or RC-KZ0092GEZZ AD
C406 VCEA0A1HW335M J 3.3 50V EL. AB å C707 VCEAGA2CW226M J 22 160V EL. AD
C407 RC-QZA104TAYK J 0.1 50V Mylar AB C711 VCKYPA1HF103Z J 0.01 50V Ceramic AA
C408 VCEA0A1CW106M J 10 16V EL. AB C712 RC-EZ0638CEZZ J 33 160V EL. AG
C409 VCEA0A1HW105M J 1.0 50V EL. AB C751 VCEA0A1CW476M J 47 16V EL. —
C410 VCKYCY1EF104Z J 0.1 25V Ceramic AA C753 VCEAGA1VW477M J 470 35V EL. AD
C411 VCEAGA1CW108M J 1000 16V EL. AD C754 VCEA0A1CW337M J 330 16V EL. AC
C413 VCKYCY1HF103Z J 0.01 50V Ceramic AA C756 VCEA0A1CW107M J 100 16V EL. AC
C414 VCKYCY1EF104Z J 0.1 25V Ceramic AA C757 RC-QZA104TAYK J 0.1 50V Mylar AB
C419 VCCCCY1HH330J J 33p 50V Ceramic AA å C758 VCEAGA2EW106M J 10 250V EL. AC
C420 VCCCCY1HH471J J 470p 50V Ceramic AA C759 VCKYPA2HB102K J 1000p 500V Ceramic AA
C451 RC-QZA563TAYK J 0.056 50V Mylar AB C801 RC-QZA223TAYK J 0.022 50V Mylar AB
C454 VCEA0A1HW475M J 4.7 50V EL. AB C802 VCEA0A1HW474M J 0.47 50V EL. AB
C502 VCEA0A1EW477M J 470 25V EL. AD C803 VCCCCY1HH120J J 12p 50V Ceramic AA
C504 VCKYPA2HB391K J 390p 500V Ceramic AA C804 VCEA0A1HW104M J 0.1 50V EL. AB
C505 VCQYTA1HM473K J 0.047 50V Mylar AB C805 VCEA0A1HW104M J 0.1 50V EL. AB
C506 RC-QZA104TAYK J 0.1 50V Mylar AB C806 VCEA0A1HW104M J 0.1 50V EL. AB
C507 RC-QZA103TAYK J 0.1 50V Mylar AA C807 VCCCCY1HH820J J 82p 50V Ceramic AA
C508 VCEAGA1VW107M J 100 35V EL. AC C901 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C509 VCKYPA2HB102K J 1000p 500V Ceramic AA C904 VCEA0A1HW335M J 3.3 50V EL. AB
C510 VCEAGA1VW477M J 470 35V EL. AD C905 VCEA0A1HW335M J 3.3 50V EL. AB
C511 VCQYTA1HM473K J 0.047 50V Mylar AB C2001 VCCCCY1HH101J J 100p 50V Ceramic AA
C513 VCEACA1HC225M J 2.2 50V EL. AC C2002 VCCCCY1HH101J J 100p 50V Ceramic AA
C514 VCEACA1HC225J J 2.2 50V EL. AC C2003 VCEA0A1CW106M J 10 16V EL. AB
C517 VCKYPA1HB102K J 1000p 50V Ceramic AA C2021 VCCCCY1HH101J J 100p 50V Ceramic AA
C522 VCKYCY1HF103Z J 0.01 50V Ceramic AA C2022 VCCCCY1HH101J J 100p 50V Ceramic AA
C551 VCSATA1CE225K J 2.2 16V Tantalum AB C2023 VCCCCY1HH101J J 100p 50V Ceramic AA

31
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9273WEV3/V6/V9 R201 VRN-MD2AL221J J 220 0.1W M-Film AA

R202 VRD-RA2BE122J J 1.2k 1/8W Carbon AA
DUNTK9316WEV1 MAIN UNIT R203 VRD-RA2BE682J J 6.8k 1/8W Carbon AA
C2024 VCCCCY1HH101J J 100p 50V Ceramic AA R204 VRN-MD2AL270J J 27 0.1W M-Film AA
C2040 VCEA0A1AW107M J 100 10V EL. AB R205 VRD-RA2BE391J J 390 1/8W Carbon AA
C2041 VCEA0A1HW105M J 1.0 50V EL. AB R206 VRD-RA2EE151J J 150 1/4W Carbon AA
C2060 RC-QZA104TAYK J 0.1 50V Mylar AB R208 VRN-MD2AL391J J 390 0.1W M-Film AA
C2061 VCKYD41HB101K J 100p 50V Ceramic AA R301 VRD-RA2BE222J J 2.2k 1/8W Carbon AA
C2062 VCEA0A1AW107M J 100 10V EL. AB R302 VRN-MD2AL102J J 1.0k 0.1W M-Film AA
C2401 VCCSD41HL560J J 56p 50V Ceramic AA R303 VRN-MD2AL103J J 10k 0.1W M-Film AA
C2601 VCEA0A1CW476M J 47 16V EL. AB R304 VRN-MD2AL333J J 33k 0.1W M-Film AA
C2602 VCCCCY1HH101J J 100p 50V Ceramic AA R307 VRN-MD2AL333J J 33k 0.1W M-Film AA
R352 VRN-MD2AL332J J 3.3k 0.1W M-Film AA
RESISTORS R353 VRN-MD2AL4R7J J 4.7 0.1W M-Film AA
(M-Ox: Metal Oxide, M-Film: Metal Film) R354 VRN-MD2AL152J J 1.5k 0.1W M-Film AA
RJ1 VRN-MD2AL000J J 0 0.1W M-Film AA R361 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
RJ5 VRN-MD2AL000J J 0 0.1W M-Film AA R364 VRN-MD2AL473J J 47k 0.1W M-Film AA
RJ6 VRN-MD2AL000J J 0 0.1W M-Film AA R401 VRN-MD2AL682J J 6.8k 0.1W M-Film AA
RJ7 VRN-MD2AL000J J 0 0.1W M-Film AA R403 VRD-RA2BE331J J 330 1/8W Carbon AA
RJ9 VRN-MD2AL000J J 0 0.1W M-Film AA R404 VRN-MD2AL391J J 390 0.1W M-Film AA
RJ10 VRN-MD2AL000J J 0 0.1W M-Film AA R405 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
RJ12 VRN-MD2AL000J J 0 0.1W M-Film AA R406 VRN-MD2AL470J J 47 0.1W M-Film AA
RJ13 VRN-MD2AL000J J 0 0.1W M-Film AA R407 VRN-MD2AL680J J 68 0.1W M-Film AA
RJ14 VRN-MD2AL000J J 0 0.1W M-Film AA R408 VRN-MD2AL102J J 1.0k 0.1W M-Film AA
RJ15 VRN-MD2AL000J J 0 0.1W M-Film AA R409 VRN-MD2AL471J J 470 0.1W M-Film AA
RJ17 VRN-MD2AL000J J 0 0.1W M-Film AA R410 VRD-RA2BE563J J 56k 1/8W Carbon AA
RJ18 VRN-MD2AL000J J 0 0.1W M-Film AA R411 VRN-MD2AL103J J 10k 0.1W M-Film AA
RJ19 VRN-MD2AL000J J 0 0.1W M-Film AA R412 VRD-RA2EE561J J 560 1/4W Carbon AA
RJ20 VRN-MD2AL000J J 0 0.1W M-Film AA R413 VRD-RA2BE470J J 47 1/8W Carbon AA
RJ21 VRN-MD2AL000J J 0 0.1W M-Film AA R414 VRD-RA2BE470J J 47 1/8W Carbon AA
RJ24 VRN-MD2AL000J J 0 0.1W M-Film AA R415 VRD-RA2BE470J J 47 1/8W Carbon AA
RJ26 VRN-MD2AL000J J 0 0.1W M-Film AA R416 VRN-MD2AL102J J 1.0k 0.1W M-Film AA
RJ29 VRN-MD2AL000J J 0 0.1W M-Film AA R417 VRD-RA2BE101J J 100 1/8W Carbon AA
RJ30 VRN-MD2AL000J J 0 0.1W M-Film AA R418 VRN-MD2AL152J J 1.5k 0.1W M-Film AA
RJ32 VRN-MD2AL000J J 0 0.1W M-Film AA R419 VRN-MD2AL472J J 4.7k 0.1W M-Film AA
RJ35 VRN-MD2AL000J J 0 0.1W M-Film AA R423 VRN-MD2AL222J J 2.2k 0.1W M-Film AA
RJ40 VRN-MD2AL000J J 0 0.1W M-Film AA R426 VRN-MD2AL271J J 270 0.1W M-Film AA
RJ49 VRN-MD2AL000J J 0 0.1W M-Film AA R440 VRN-MD2AL821J J 820 0.1W M-Film AA
RJ50 VRN-MD2AL000J J 0 0.1W M-Film AA å R451 VRS-VV3AB103J J 10k 1W M-Ox. AA
å RJ51 VRN-MD2AL000J J 0 0.1W M-Film AA R452 VRD-RA2BE152J J 1.5k 1/8W Carbon AA
å RJ52 VRN-MD2AL000J J 0 0.1W M-Film AA R454 VRD-RA2BE274J J 270k 1/8W Carbon AA
å RJ53 VRN-MD2AL000J J 0 0.1W M-Film AA R455 VRD-RA2BE392J J 3.9k 1/8W Carbon AA
RJ55 VRN-MD2AL000J J 0 0.1W M-Film AA R456 VRN-MD2AL223J J 22k 0.1W M-Film
RJ59 VRN-MD2AL000J J 0 0.1W M-Film AA R457 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
RJ62 VRN-MD2AL000J J 0 0.1W M-Film AA R458 VRD-RA2BE474J J 470k 1/8W Carbon AA
RJ63 VRN-MD2AL000J J 0 0.1W M-Film AA R459 VRD-RA2BE123J J 12k 1/8W Carbon AA
RJ64 VRN-MD2AL000J J 0 0.1W M-Film AA R504 VRD-RA2BE471J J 470 1/8W Carbon AA
RJ66 VRN-MD2AL000J J 0 0.1W M-Film AA R505 VRD-RA2BE101J J 100 1/8W Carbon AA
RJ68 VRN-MD2AL000J J 0 0.1W M-Film AA R506 VRD-RA2BE683G J 68k 1/8W Carbon AA
å R51 VRS-VV3AB331J J 330 1W M-Ox. AA R507 VRD-RA2BE104G J 100k 1/8W Carbon AA
å R52 VRS-VV3DB470J J 47 2W M-Ox. AA R508 VRD-RA2BE473J J 47k 1/8W Carbon AA
å R53 VRS-VV3LB223J J 22k 3.0W M-Ox. AB R510 VRD-RM2HD1R5J J 1.5 1/2W Carbon AA
R54 VRN-MD2AL101J J 100 0.1W M-Film AA (20J-S100/21MJ50/CJ20S10)
R55 VRN-MD2AL101J J 100 0.1W M-Film AA R510 VRD-RM2HD1R2J J 1.2 1/2W Carbon AA
R56 VRN-MD2AL823J J 82k 0.1W M-Film AA (20J-S100S)
R57 VRN-MD2AL223J J 22k 0.1W M-Film AA å R511 VRN-SV2HB1R5J J 1.5 1/2W M-Film AA

32
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9273WEV3/V6/V9 å R758 VRS-SV2HC180J J 18 1/2W M-Ox. AA

R801 VRN-MD2AL332J J 3.3k 0.1W M-Film AA
DUNTK9316WEV1 MAIN UNIT R802 VRN-MD2AL332J J 3.3k 0.1W M-Film AA
R512 VRD-RM2HD331J J 330 1/2W Carbon AA R803 VRN-MD2AL182J J 1.8k 0.1W M-Film AA
R516 VRD-RA2BE683G J 68k 1/8W Carbon AA R804 VRN-MD2AL182J J 1.8k 0.1W M-Film AA
R517 VRD-RA2BE103G J 10k 1/8W Carbon AA R805 VRN-MD2AL182J J 1.8k 0.1W M-Film AA
R518 VRD-RA2BE154J J 150k 1/8W Carbon AA R806 VRN-MD2AL333J J 33k 0.1W M-Film AA
R524 VRN-MD2AL332J J 3.3k 0.1W M-Film AA R902 VRN-MD2AL750J J 75 0.1W M-Film AA
R525 VRD-RA2BE473J J 47k 1/8W Carbon AA R905 VRN-MD2AL102J J 1.0k 0.1W M-Film AA
R552 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R906 VRN-MD2AL102J J 1.0k 0.1W M-Film AA
R553 VRN-MD2AL273J J 27k 0.1W M-Film AA R924 VRN-MD2AL104J J 100k 0.1W M-Film AA
R554 VRN-MD2AL472J J 4.7k 0.1W M-Film AA R925 VRN-MD2AL104J J 100k 0.1W M-Film AA
R602 VRD-RA2EE820J J 82 1/4W Carbon AA R961 VRN-MD2AL101J J 100 0.1W M-Film AA
å R603 VRS-SV3LB220J J 22 3.0W M-Ox. AB R962 VRN-MD2AL101J J 100 0.1W M-Film AA
R605 VRN-MD2AL332J J 3.3k 0.1W M-Film AA R2001 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
R606 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R2002 VRN-MD2AL103J J 10k 0.1W M-Film AA
R607 VRD-RA2BE101J J 100 1/8W Carbon AA R2006 VRN-MD2AL103J J 10k 0.1W M-Film AA
R608 VRD-RA2BE101J J 100 1/8W Carbon AA R2008 VRD-RA2BE224J J 220k 1/8W Carbon AA
R609 VRD-RA2BE331J J 330 1/8W Carbon AA R2009 VRN-MD2AL102J J 1.0k 0.1W M-Film AA
R610 VRS-VV3DB391J J 390 2W M-Ox. AA R2010 VRN-MD2AL102J J 1.0k 0.1W M-Film AA
R620 VRD-RA2BE103J J 10k 1/8W Carbon AA R2011 VRN-MD2AL821J J 820 0.1W M-Film AA
R621 VRN-MD2AL682J J 6.8k 0.1W M-Film AA R2012 VRN-MD2AL471J J 470 0.1W M-Film AA
R631 VRN-MD2AL391J J 390 0.1W M-Film AA R2020 VRD-RM2HD223J J 22k 1/2W Carbon AA
R632 VRN-MD2AL152J J 1.5k 0.1W M-Film AA R2022 VRD-RA2BE333J J 33k 1/8W Carbon AA
R633 VRN-MD2AL472J J 4.7k 0.1W M-Film AA R2024 VRD-RA2BE682J J 6.8k 1/8W Carbon AA
R634 VRD-RM2HD101J J 100 1/2W Carbon AA R2025 VRD-RA2BE682J J 6.8k 1/8W Carbon AA
R641 VRS-VV3AB682J J 6.8k 1W M-Ox. AA R2026 VRD-RA2BE682J J 6.8k 1/8W Carbon AA
R642 VRD-RA2BE821J J 820 1/8W Carbon AA R2027 VRD-RA2BE682J J 6.8k 1/8W Carbon AA
çå R651 VRD-RM2HD1R0J J 1.0 1/2W Carbon AA R2028 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
çå R653 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R2029 VRN-MD2AL102J J 1.0k 0.1W M-Film AA
çå R654 VRD-RA2BE473J J 47k 1/8W Carbon AA R2031 VRN-MD2AL103J J 10k 0.1W M-Film AA
çå R655 VRN-MD2AL104J J 100k 0.1W M-Film AA R2032 VRN-MD2AL471J J 470 0.1W M-Film AA
å R659 VRN-VV3AB2R7J J 2.7 1W M-Film AA R2040 VRN-MD2AL102J J 1.0k 0.1W M-Film AA
å R661 VRN-VV3ABR47J J 0.47 1W M-Film AA R2041 VRN-MD2AL333J J 33k 0.1W M-Film AA
å R701 VRC-UA2HG275K J 2.7M 1/2W Solid AA R2042 VRN-MD2AL101J J 100 0.1W M-Film AA
or RR-DZ0047CEZZ (20J-S100/S100S/21MJ50) R2043 VRN-MD2AL101J J 100 0.1W M-Film AA
å R701 VRC-UB2HG275K 2.7M 1/2W Solid AA R2044 VRN-MD2AL682J J 6.8k 0.1W M-Film AA
(CJ20S10) R2045 VRN-MD2AL101J J 100 0.1W M-Film AA
å R702 VRW-KP3HC1R8K J 1.8 5W Cement AC R2047 VRN-MD2AL221J J 220 0.1W M-Film AA
å R703 VRS-KA3NG681J J 680 7W M-Ox. AF R2048 VRD-RA2BE562J J 5.6k 1/8W Carbon AA
å R704 VRS-VV3AB123J J 12k 1W M-Ox. AA R2049 VRN-MD2AL333J J 33k 0.1W M-Film AA
R705 VRD-RA2EE334J J 330k 1/4W Carbon AA R2054 VRN-MD2AL103J J 10k 0.1W M-Film AA
R706 VRD-RM2HD470J J 47 1/2W Carbon AA R2055 VRN-MD2AL103J J 10k 0.1W M-Film AA
å R707 VRN-VV3DB1R5J J 1.5 2W M-Film AB R2060 VRN-MD2AL221J J 220 0.1W M-Film AA
å R708 VRD-RM2HD824J J 820k 1/2W Carbon AA R2061 VRN-MD2AL562J J 5.6k 0.1W M-Film AA
å R709 VRS-KA3NG681J J 680 7W M-Ox. AF R2062 VRN-MD2AL183J J 18k 0.1W M-Film AA
å R711 VRS-KA3NG681J J 680 7W M-Ox. AF R2063 VRD-RA2BE222J J 2.2k 1/8W Carbon AA
å R717 VRS-KA3HG3R3K J 3.3 5W M-Ox. AD R2064 VRD-RA2BE332J J 3.3k 1/8W Carbon AA
å R730 VRN-VV3LB2R7J J 2.7 3W M-Film AB R2066 VRN-MD2AL103J J 10k 0.1W M-Film AA
R731 VRD-RA2EE330J J 33 1/4W Carbon AA R2067 VRN-MD2AL103J J 10k 0.1W M-Film AA
å R734 VRS-KA3NG330J J 33 7W M-Ox. AE R2068 VRN-MD2AL103J J 10k 0.1W M-Film AA
R751 VRD-RM2HD331J J 330 1/2W Carbon AA R2070 VRN-MD2AL103J J 10k 0.1W M-Film AA
R752 VRD-RA2BE562J J 5.6k 1/8W Carbon AA R2101 VRN-MD2AL101J J 100 0.1W M-Film AA
R754 VRD-RA2BE223J J 22k 1/8W Carbon AA R2102 VRN-MD2AL101J J 100 0.1W M-Film AA
å R755 VRS-VV3DB470J J 47 2W M-Ox. AA R2501 VRN-MD2AL123J J 12k 0.1W M-Film AA
R757 VRD-RA2BE472J J 4.7k 1/8W Carbon AA R2503 VRN-MD2AL273J J 27k 0.1W M-Film AA

33
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9273WEV3/V6/V9 DUNTK9274WEV3
DUNTK9316WEV1 MAIN UNIT DUNTK9274WEV3 CRT UNIT
R2504 VRN-MD2AL123J J 12k 0.1W M-Film AA TRANSISTORS
R2505 VRN-MD2AL563J J 56k 0.1W M-Film AA Q852 VS2SC2229O/1E J 2SC2229 (O) AD
R2506 VRD-RA2BE563J J 56k 1/8W Carbon AA Q854 VS2SC2229O/1E J 2SC2229 (O) AD
R2507 VRN-MD2AL823J J 82k 0.1W M-Film AA Q856 VS2SC2229O/1E J 2SC2229 (O) AD
R2508 VRN-MD2AL153J J 15k 0.1W M-Film AA Q881 VS2SA1266-Y-1 J 2SA1266 (Y) AA
R2509 VRN-MD2AL272J J 2.7k 0.1W M-Film AA or VS2SA1015Y/-1
R2601 VRD-RA2BE470J J 47 1/8W Carbon AA
DIODES AND COIL
SWITCHES D881 VHD1SS119//-1 J Diode AB
S2501 QSW-K0079GEZZ J Power AB D882 VHD1SS119//-1 J Diode AB
S2502 QSW-K0079GEZZ J Vol.-Down AB D885 VHD1SS119//-1 J Diode AB
S2503 QSW-K0079GEZZ J Vol.-Up AB L851 VP-DF151K0000 J Peaking 150µH AB
S2504 QSW-K0079GEZZ J Ch.-Down AB
S2505 QSW-K0079GEZZ J Ch.-Up AB CASPACITORS
(EL: Electrolytic, M-Poly.: Metalized Polypro Film)
MISCELLANEOUS PARTS C851 VCCCCY1HH271J J 270p 50V Ceramic AA
å RY701 RRLYU0036CEZZ J Relay AM C852 VCCCCY1HH271J J 270p 50V Ceramic AA
or RRLYU0028CEZZ AK C853 VCCCCY1HH271J J 270p 50V Ceramic AA
å F701 QFS-B4023CEZZ J Fuse AC C854 RC-KZ0016CEZZ J 0.1 1.4kV Ceramic AC
FB602 RBLN-0037CEZZ J Balun AB C858 VCKYCY1HB102K J 1000p 50V Ceramic AA
FB603 RBLN-0037CEZZ J Balun AB C881 VCEA0A1CW106M J 10 16V EL. AB
FH701 QFSHD1013CEZZ J Fuse Holder AC C883 VCEA0A1CW336M J 33 16V EL. AB
or QFSHD1009CEZZ
FH702 QFSHD1014CEZZ J Fuse Holder AC RESISTORS
or QFSHD1010CEZZ (M-Ox: Metal Oxide, M-Film: Metal Film)
J903 QJAKE0159CEZZ J Jack AF R851 VRN-MD2AL470J J 47 0.1W M-Film AA
J904 QJAKE0160CEZZ J Jack AF R852 VRD-RA2BE221J J 220 1/8W Carbon AA
J905 QJAKE0158CEZZ J Jack AF R853 VRN-MD2AL121J J 120 0.1W M-Film AA
P301 QPLGN0661CEZZ J Plug AD å R857 VRS-VV3AB123J J 12k 1W M-Ox. AA
P302 QPLGN0461CEZZ J Plug AB R858 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
P401 QPLGN0561CEZZ J Plug AB R859 VRN-MD2AL470J J 47 0.1W M-Film AA
P601 QPLGN0603CEZZ J Plug AB (20J-S100/21MJ50/CJ20S10)
P651 QPLGN0361CEZZ J Plug AB R859 VRD-RA2BE470J J 47 1/8W Carbon AA
P701 QPLGN0207CEZZ J Plug AA (20J-S100S)
P751 QPLGN0461CEZZ J Plug AB R860 VRD-RA2BE221J J 220 1/8W Carbon AA
P2001 QPLGN0561CEZZ J Plug AB (20J-S100/21MJ50/CJ20S10)
SC3001 QSOCN0259FJ00 J Socket AE R860 VRN-MD2AL221J J 220 0.1W M-Film AA
RMC2601 RRMCU0222CEZZ J Remote Receiver AL (20J-S100S)
RDA501 PRDAR0218PEFW M Heat Sink AD R861 VRN-MD2AL121J J 120 0.1W M-Film AA
RDA602 PRDAR0216PEFW M Heat Sink AE å R865 VRS-VV3AB123J J 12k 1W M-Ox. AA
RDA701 PRDAR0238PEFW M Heat Sink AN R866 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
TP701 QLUGP0102PEZZ M Lug AA R867 VRD-RA2BE470J J 47 1/8W Carbon AA
PZETM0016CEZZ J Insulator AB (20J-S100/21MJ50/CJ20S10)
LHLDW1002PEZZ M Holder AB R867 VRN-MD2AL470J J 47 0.1W M-Film AA
(20J-S100S)
R868 VRN-MD2AL221J J 220 0.1W M-Film AA
(20J-S100/21MJ50/CJ20S10)
R868 VRD-RA2BE221J J 220 1/8W Carbon AA
(20J-S100S)
R869 VRN-MD2AL121J J 120 0.1W M-Film AA
å R873 VRS-VV3AB123J J 12k 1W M-Ox. AA
R874 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
R881 VRN-MD2AL561J J 560 0.1W M-Film AA

34
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

DUNTK9274WEV3 C3014 RC-QZA473TAYK J 0.047 50V Mylar AB

C3015 VCSATA1CE335K J 3.3 16V Tantalum AC
DUNTK9274WEV3 CRT UNIT C3016 VCE9GA1HW475M J 4.7 50V EL. AB
R882 VRN-MD2AL391J J 390 0.1W M-Film AA C3017 VCSATA1CE106K J 10 16V Tantalum AD
R883 VRD-RA2BE561J J 560 1/8W Carbon AA C3018 VCEA0A1HW105M J 1.0 50V EL. AB
R884 VRN-MD2AL152J J 1.5k 0.1W M-Film AA C3019 VCEA0A1HW475M J 4.7 50V EL. AB
R886 VRN-MD2AL431J J 430 0.1W M-Film AA C3020 VCEA0A1HW475M J 4.7 50V EL. AB

MISCELLANEOUS PARTS RESISTORS

P851 QPLGN0561CEZZ J Plug AB (M-Ox: Metal Oxide, M-Film: Metal Film)
P852 QPLGN0461CEZZ J Plug AB RJ2 VRS-CY1JF000J J 0 1/16W M-Ox. AA
SC851 QSOCV0840CEZZ J Socket AK RJ3 VRS-CY1JF000J J 0 1/16W M-Ox. AA
or QSOCV0826CEZZ (20J-S100/21MJ50/ AK RJ4 VRS-CY1JF000J J 0 1/16W M-Ox. AA
CJ20S10) RJ6 VRS-CY1JF000J J 0 1/16W M-Ox. AA
SC851 QSOCV0913CEZZ J Socket (20J-S100S) AK RJ7 VRS-CY1JF000J J 0 1/16W M-Ox. AA
or QSOCV0929CEZZ AM RJ8 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ9 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ12 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ15 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R305 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
R306 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA
R355 VRS-CY1JF333J J 33k 1/16W M-Ox. AA
R356 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R357 VRS-CY1JF4R7J J 4.7 1/16W M-Ox. AA
DUNTK9275WEV5 R358 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA
MTS UNIT R362 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
INTEGRATED CIRCUITS R3001 VRS-CY1JF221J J 220 1/16W M-Ox. AA
IC352 VHiTDA7233/-1 J TDA7233 AF R3002 VRS-CY1JF221J J 220 1/16W M-Ox. AA
IC3001 VHiCXA2053Q-1 J CXA2053Q/ AX R3003 VRS-CY1JF105J J 1M 1/16W M-Ox. AA
R3004 VRS-CY1JF104J J 100k 1/16W M-Ox. AA
TRANSISTORS R3005 VRS-CY1JF623J J 62k 1/16W M-Ox. AA
Q301 VS2SD601AR/-1 J AC R3007 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
Q352 VS2SC945AQ/-1 J AB R3008 VRS-CY1JF302J J 3k 1/16W M-Ox. AA
R3010 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA
CAPACITORS R3011 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
(EL: Electrolytic, M-Poly.: Metalized Polypro Film) R3012 VRS-CY1JF102J J 1k 1/16W M-Ox. AA
C315 VCEA0A1HW225M J 2.2 50V EL. AB
C356 VCKYCY1HB562K J 5600p 50V Ceramic AA MISCELLANEOUS PARTS
C357 VCEA0A1CW107M J 100 16V EL. AC P351 QPLGN0661CEZZ J Plug AD
C358 VCEA0A1CW337M J 330 16V EL. AC P3001 QPLGN0242FJ00 J Plug AE
C359 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C360 VCEA0A1CW226M J 22 16V EL. AB
C365 VCEAGA1CW108M J 1000 16V EL. AD
C3001 VCE9GA1HW475M J 4.7 50V EL. AB
C3002 VCKYCY1HB562K J 5600p 50V Ceramic AA
C3003 RC-QZA123TAYK J 0.012 50V Mylar AB
C3004 VCEA0A1HW105M J 1.0 50V EL. AB
C3005 VCEA0A1HW475M J 4.7 50V EL. AB
C3006 VCEA0A1HW106M J 10 50V EL. AB
C3007 VCEA0A1HW475M J 4.7 50V EL. AB
C3008 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C3009 VCEA0A1CW227M J 220 16V EL. AC
C3010 VCE9GA1HW475M J 4.7 50V EL. AB
C3011 VCEA0A1HW475M J 4.7 50V EL. AB
C3012 VCE9GA1HW475M J 4.7 50V EL. AB
C3013 VCKYCY1HB272K J 2700p 50V Ceramic AA

35
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

CABINET PARTS

1 CCABA1279MES0 M Cabinet Complete Ass'y BC

1-1 _ _ Cabinet Front —
1-2 GCOVA1034MEKA M Cover for R/C AC
1
1-3 HBDGB3009MESA M Badge "SHARP" AC
1-4 JBTN-1098MEKA M Button,Power, AD 1-1
Ch/Vol-up/down
2 GCABB1126MEKA M Cabinet,Rear AX

MTS STEREO
O -R
– VOL + ? CH > VIDEO IN L- AUDI
POWER

MESCELLANEOUS PARTS
1-3 1-4
1-2
SP1 VSP0080PBK98A M Speaker, 2pcs used —
SP2 VSP0080PBK98A M Speaker —
å ACC701 QACCD3051CESA M AC Cord AK
or QACCD3037CESA AC Cord
or QACCD3038CESA AC Cord
QCNW-2110PEZZ R Connecting Cord —
QCNW-2111PEZZ R Connecting Cord —
QCNW-2116PEZZ R Connecting Cord —
QCNW-2150PEZZ R Connecting Cord —

SUPPLIEDACCESSORIES

RRMCG1324CESA M Infrared R/C AQ

(20J-S100/S100S/21MJ50)
RRMCG1339CESA M Infrared R/C —
(CJ20S10)
TGAN-1006MEZZ M Guarantee Card AA
(20J-S100/100S)
TiNS-6033MEZZ M Operation Manual AC
(20J-S100/100S)
TiNS-6083MEZZ M Operation Manual AE
(CJ20S10)
TiNS-6087MEZZ M Operation Manual AE
(21MJ50)

PACKING PARTS

SPAKC0573MEZZ M Packing Case —

(20J-S100/100S/CJ20S10)
SPAKC0579MEZZ M Packing Case (21MJ50) —
SPAKP0023MEZZ M Polyethylene Sack —
SPAKX0167MEZZ M Buffer Material —
SSAKA0004MEZZ M Polyethylene Sack —

36
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

Ref. No. Part No. ★ Description

Code ★
PACKING OFRef.
THE No. Part No.
SET Description Code

★ Polystyrene Bag

Operation manual
Guarantee Card
and batteries

★Polystyrene mat

★ Buffer material

FRONT ★ Packing case

Use tapes to
fix the packing
case.
REAR

37
Downloaded from www.Manualslib.com manuals search engine
 20J-S100/100S
CJ20S10/21MJ50

TQ0286-S
Printed in U.S.A
Y.O

Downloaded from www.Manualslib.com manuals search engine