Service Manual: GX-CD1200W (BK) GX-CD1200W (GL)

GX-CD1200W
SERVICE MANUAL
No. S5039GXCD1200
PORTABLE CD STEREO
COMPONENT SYSTEM
GX-CD1200W(BK)
MODEL GX-CD1200W(GL)
• In the interests of user-safety the set should be restored to its original
condition and only parts identical to those specified should be used.
CONTENTS
Page
SPECIFICATIONS ............................................................................................................................................................... 1
VOLTAGE SELECTION ....................................................................................................................................................... 2
AC POWER SUPPLY CORD AND AC PLUG ADAPTOR ................................................................................................... 2
FITTING OF DIAL POINTER ............................................................................................................................................... 2
NAMES OF PARTS ............................................................................................................................................................. 3
DISASSEMBLY .................................................................................................................................................................... 4
REMOVING AND REINSTALLING THE MAIN PARTS ....................................................................................................... 5
ADJUSTMENT ..................................................................................................................................................................... 6
SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD ............................................................................................... 10
NOTES ON SCHEMATIC DIAGRAM ................................................................................................................................ 18
TYPES OF TRANSISTOR AND LED................................................................................................................................. 18
VOLTAGE .......................................................................................................................................................................... 18
WAVEFORMS OF CD CIRCUIT ........................................................................................................................................ 19
TROUBLESHOOTING (CD SECTION) ............................................................................................................................. 20
FUNCTION......................................................................................................................................................................... 24
PARTS GUIDE / EXPLODED VIEW
SPECIFICATIONS
General Radio section
Power source: AC 110-127 V/220-240 V, 50/60 Hz Frequency range: FM; 88 - 108 MHz
DC 15 V [“D” size (UM/SUM-1, R20 or HP- SW1; 2.3 - 7.3 MHz
2) battery x 10] SW2; 7.3 - 22 MHz
Power consumption: 31 W MW; 526.5 - 1,606.5 kHz
Output power: PMPO; 200 W (Total)
(AC operation) Tape recorder section
MPO; 50 W (25 W + 25 W) Frequency response: 60 - 12,000 Hz (Normal tape)
(AC operation) Signal/noise ratio: 40 dB (TAPE 1, recording/playback)
RMS; 25 W (12.5 W + 12.5 W) 55 dB (TAPE 2, playback)
(DC operation, 10 % T.H.D.) Wow and flutter: 0.15 % (WRMS)
Input terminal: Mixing microphone(monaural); 600 ohms Motor: DC 9 V electric governor
Output terminal: Headphones; 16-50 ohms Bias system: AC bias
(recommended; 32 ohms) Erase system: Magnet erase
Dimensions: Width; 300 mm (11-13/16")
Height; 262 mm (9-1/2") Speaker section
Depth; 220 mm (8-11/16") Type: 2-way type
Weight: 4.1 kg (9.1 lbs.) without batteries Speakers: 12 cm (4-3/4") free-edge speaker x 2
Tweeter x 2
Maximum input power: 25 W
Compact disc player Rated input power: 12.5 W
Type: Compact disc Impedance: 8 ohms
Signal readout: Non-contact, 3-beam semi-conductor laser Dimensions: Width; 235 mm (9-1/4")
pickup Height; 262 mm (10-5/16")
Audio channels: 2 Depth; 220 mm (8-11/16")
Filter: 8-times oversampling digital filter Weight: 1.8 kg (4.0 lbs.)/each
D/A converter: 1-bit D/A converter
Wow and flutter: Unmeasurable Specifications for this model are subject to change without
(less than 0.001 % W. peak) prior notice.
This document has been published to be used

SHARP CORPORATION for after sales service only.
–1– The contents are subject to change without notice.
Downloaded from www.Manualslib.com manuals search engine

GX-CD1200W
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
VOLTAGE SELECTION
Before operating the unit on mains, check the preset voltage. If the voltage is different from your local voltage, adjust the voltage
as follows: Slide the voltage selector with a screwdriver to the appropriate voltage number (AC 110V-127V or AC 220V-240V).
AC POWER SUPPLY CORD AND AC PLUG ADAPTOR

QACCE0007AW00 QACCA0001SJ00
QACCL0002AW00 QPLGA0250AFZZ QPLGA0253AFZZ
FITTING OF DIAL POINTER

1. Remove the Main PWB, the Graphic Equalizer PWB, the "0" Point
Volume PWB and the Fine Tuning PWB. (See Figure 4-2
in the "Disassembly" on page 4.)
2. Remove the dial pointer guide and PWB. Dial Pointer(211)
3. Insert the dial pointer from A , lead it under B , hang it on A
Front Cabinet
the tuner gear and then pass it through C .
Tuning Knob
4. Replace the Main PWB, the Graphic Equalizer PWB, the B
Volume PWB and the Fine Tuning PWB. Dial Pointer(211)
5. Rotate the tuning knob in the arrow direction until it stops. Graphic Equalizer
(Set the tuner variable capacitor to "0" point (F-LOW Fine Tuning PWB
PWB
state).)
6. Adjust the dial pointer so that its stopper becomes the
Screw(601)
Figure 2-2 position. (Adjust the engagement of the pointer C
ø3x10mm
gear and the tuner gear to get the minimum space between PWB
the PWB and the stopper.) This position is the "0" point.
Tuner
7. Screw up the PWB and the dial pointer guide. Gear
Dial Pointer Guide Volume PWB
(218)
Main PWB
Figure 2-1
Make the minimum space.

PWB
Dial Pointer
Stopper
Pointer Gear
Tuner Gear
Main PWB
Front Cabinet
Variable Capacitor
Figure 2-2
–2–

GX-CD1200W
NAMES OF PARTS
1. CD Compartment
2. CD Eject Button
(Continued) 1
3. Track Number Indicator
4. (CD) Play Indicator
5. (CD) Pause Indicator
6. Extra Bass Control 2
7. Graphic Equalizer Controls
8. Power/(TAPE 2) Play Direction Indicators
9. (CD) Track Down/Review Button
10. (CD) Track Up/Cue Button
11. (CD) Stop Button
12. (CD) Play/Pause Button 3
13. Fine Tuning Control 4
14. Built-in Microphone
15. Volume Control 5
16. Headphone Socket
17. Mixing Microphone Socket 6 7 8 9 10 11 12 13
18. Function Selector Switch
19. (TAPE 1) Cassette Compartment
20. Tuning Control 20
21. FM Stereo Indicator 14
22. Surround Indicator 21
23. Surround Switch 15 22
24. Band Selector Switch
16 23
25. Dubbing Speed/Built-in Microphone/FM Mode Switch
26. (TAPE 2) Cassette Compartment 17 24
18 25
27. (TAPE 1) Record Button
28. (TAPE 1) Play Button 19 26
29. (TAPE 1) Rewind Button
30. (TAPE 1) Fast Forward Button 27 28 29 30 31 32
31. (TAPE 1) Stop/Eject Button
32. (TAPE 1) Pause Button
33. (TAPE 2) Reverse Mode Switch
34. (TAPE 2) Play Button
35. (TAPE 2) Fast Wind Buttons
36. (TAPE 2) Stop/Eject Button 33 34 35 36 37
37. (TAPE 2) Direction Switch
38. FM/SW Telescopic Rod Aerial 38

39. Beat Cancel Switch
40. Speaker Terminals 39
41. AC Voltage Selector
42. AC Power Input Socket 40
43. Battery Compartment
41
44. Tweeter
45. Bass Reflex Duct
46. Woofer
42
47. Speaker Release Lever
48. Speaker Wire
43
44 47
45
46 48
–3–

GX-CD1200W
DISASSEMBLY
Caution on Disassembly
Follow the below-mentioned notes when disassembling CD Player Unit
the unit and reassembling it, to keep it safe and ensure Front Cabinet
excellent performance:
1. Take cassette tape out of the unit.
2. Be sure to remove the power supply plug from the wall
outlet before starting to disassemble the unit and remove
the batteries from the unit.
3. Take off nylon bands or wire holders where they need (B1)x2
to be removed when disassembling the unit. After ø3x10mm
servicing the unit, be sure to rearrange the leads where
they were before disassembling. CD SERVO PWB
4. Take sufficient care on static electricity of integrated
circuits and other circuits when servicing.
(B2)x1
MAIN UNIT
STEP REMOVAL PROCEDURE FIGURE Figure 4-2
1 Front Cabinet/ 1. Battery Compartment Lid. 4-1
Rear Cabinet ................................. (A1)x1
2. Screw ................... (A2)x5 Fine Tuning
PWB Volume Graphic
3. Screw ................... (A3)x3 PWB
4. Socket .................. (A4)x1 Equalizer
PWB (C1)x1
Front Cabinet
2 CD Player Unit 1. Screw ................... (B1)x2 4-2 Nat
2.Socket ................... (B2)x1
3 Main PWB/ 1. Knob ..................... (C1)x1 4-3
Graphic Equalizer 2. Socket .................. (C2)x3 Washer
Main PWB
PWB/ 3. Screw ................... (C3)x5
Volume PWB/ 4. Screw ................... (C4)x2
Fine Tuning PWB 5. Mic ....................... (C5)x1
4 Tape mechanism 1. Open the cassette holder. 4-3 Open
2. Screw ................... (D1)x6 (C4)x2
ø3x10mm (C5)x1
5 Power PWB/ 1. Screw ................... (E1)x3 4-4
Terminal A PWB/ 2. Screw ................... (E2)x2
Terminal B PWB 3. Bracket ................. (E3)x1 (D1)x4
4. Screw ................... (E4)x2 ø3x10mm
5. Hook ..................... (E5)x2
6 CD Servo PWB/ 1. Screw ................... (F1)x7 5-1 (C3)x5 Cassette
CD Control PWB/ 2. Socket .................. (F2)x3 Holder
ø3x10mm
(D1)x2 Tape (Left/Right)
7 CD Mechanism 1. Screw ................... (G1)x1 5-1 (C2)x3 ø3x10mm Mechanism
SPEAKER UNIT Figure 4-3
STEP REMOVAL PROCEDURE FIGURE
1 Speaker 1. Screw ................... (H1)x5 5-2
2. Front Panel .......... (H2)x1 Power
3. Screw ................... (H3)x4 Transeformer
Main PWB Rear Cabinet Voltage Selector

AC Socket
(A2)x1 Power
PWB
ø3x6mm
(A4)x1
(A3)x3 Front
ø3x20mm Cabinet
(E5)x2
(A2)x3 (E1)x3
ø3x6mm ø3x10mm
(E2)x2
ø4x16mm
(E3)x1
(A2)x1 (E4)x2
ø3x6mm ø3x10mm Terminal B
Rear PWB
Cabinet Terminal A
(A1)x1 PWB
Figure 4-1 Figure 4-4
–4–

GX-CD1200W
(F1)x3 Front Panel
(H2)x1 Tweeter
CD Servo ø3x10mm
(G1)x3
PWB
ø3x10mm Woofer Speaker Cord
(F2)x2 Speaker
Holder
Cord
Driver
(F2)x1
CD Mechanism
(F1)x1
ø3x10mm
(H3)x4
ø3x10mm
Switch PWB
Main Unit
CD Player Unit Speaker

Release (H1)x5
(F1)x3 Lever Speaker Box ø4x16mm
ø3x10mm CD Control PWB
Figure 5-2
Figure 5-1
REMOVING AND REINSTALLING THE MAIN PARTS

CD MECHANISM SECTION
Perform steps 1,2,6 and 7 of the disassembly method to (A1)x2
remove the CD mechanism.
How to remove the pickup (See Fig. 5-3.)
1. Remove the hooks (A1) x 2 pcs., to remove the CD (A2)x1
Mechanism Cover (A2) x1 pc.
2. Remove the screws (A3) x 2 pcs., to remove the shaft (A4)
x1 pc. (A3) x2
ø2.6 x6mm CD
3. Remove the stop washer (A5) x1 pc., to remove the gear Mechanism
(A6) x 1 pc. Pickup
4. Remove the pickup.
Note : (Figure 5-1 and Figure 5-3)
After removing the connector for the optical pick-up from Stop
the connector, wrap the conductive aluminium foil around Washer
the front end of connector to protect the optical pick-up from Gear (A5) x1
electrostatic damage. Shaft (A6) x1
(A4) x1
Figure 5-3
–5–

GX-CD1200W
TAPE MECHANISM SECTION
Perform steps 1, 2, 3 and 4 of the disassembly method to (A1) x1
remove the mechanism block. ø2x7mm TAPE 1
(A1) x1
Hook ø2x3mm
(A2) x2
How to remove the record / playback, playback Record/Playback
Head
and erase heads (See Figs. 6-1 and 6-2.)
1. Remove the screws (A1) x 2 pcs., to remove the record/
playback head.
2. Remove the hooks (A2) x 2 pcs., toward the center position
as shown in Fig. 6-1. and then extract the erase head
upward.
Erase
3. Remove the screws (B1) x 2 pcs., to remove the playback Head
head.
Note:
After replacing the heads and performing the azimuth adjust- Figure 6-1
ment, be sure to apply screw lock.
(B1) x1 (B1) x1 TAPE 2
How to remove the pinch roller (See Fig. 6-3.) ø2x7mm ø2x3mm
1. Carefully bend the pinch roller pawl in the direction of the Playback
Head
arrow <A> , and remove the pinch roller (C1) upwards.
How to remove the motor (See Fig. 6-4.)

1. Remove the belt.
2. Remove the screws (D1) x 4 pcs., to remove the motor
bracket.
3. Remove the screws (D2) x 3 pcs., to remove the motor.
Note:
When mounting the motor, pay attention to the motor mount-
ing angle.
How to remove the belts (See Fig. 6-5.) Figure 6-2

1. Remove the main belt (E1) x 1 pc., at the tape 1 side from
the motor pulley.
2. Remove the main belt (E2) x 1 pc., at the tape 2 side from Pinch Roller
the motor pulley. (C1)
3. Remove the REW/FF belt (E3) x 2 pcs., from the REW/FF
roller. Pinch Roller
4. Put on the belts in the reverse order of removal. Pawl
Note:
When putting on the belt, ascertain that the belt is not twisted,
and clean it. <A>
Figure 6-3
( D1 ) x2
( D1 ) x2 ø2 x 4mm
ø2 x 4mm
Motor Motor
TAPE 2 TAPE 1
Main Belt Main Belt Motor
REW / FF Bracket
Belt
TAPE 2 (E3) x1 ( D2 ) x3
Special Screw
Motor
Main
Belt
(E1) x1 TAPE 1
Main
Belt
(E2) x1 Motor
Bracket
REW / FF
Belt Motor
(E3) x1
Figure 6-5 Figure 6-4
–6–

GX-CD1200W
ADJUSTMENT
MECHANISM SECTION TUNER SECTION

• Driving Force Check fL: Low-range frequency
fH: High-range frequency
Torque Meter Specified Value
Play: TW-2412 Tape 1: Over 60 g • FM IF/RF
Tape 2: Over 50 g Specified Value/
Instrument
Test Stage Adjusting
Connection
Point
• Torque Check
FM IF L9 Input: FM Antenna
Torque Meter Specified Value
FM Detection L10 Output:Pin 9 of IC2
Tape 1 Tape 2 FM Band fL: L1 Input: Antenna
Play: TW-2111 30 to 70 g.cm 27 to 60 g.cm Coverage fH: TC1 Output: Headphone Socket
FM Tracking fL(88.0 MHz): L2 (Load resistance:
Fast Forward: TW-2231 Over 55 g.cm 55 to 120 g.cm
fH(108 MHz): TC2 32 ohms)
Rewind: TW-2231 Over 55 g.cm 55 to 120 g.cm
• AM IF/RF
• Head Azimuth
Specified Value/ Instrument
Test Tape Instrument Connection Test Stage Adjusting Connection
MTT-114 Headphones Socket Point
(Load resistance: 32 ohms) AM IF L11 Input: Antenna
Output: Pin 9 of IC2
• Tape Speed (Normal only) MW Band fL: L6 Input: Antenna

Coverage fH: TC3 Output: Headphone Socket
Test Tape Adjustment Specified Instrument MW Tracking fL(600 kHz): L3 (Load resistance:
Point Value Connection
fH(1,400 kHz):TC4 32 ohms)
MTT-111 Tape 1,2:VR102 3,000 ± 60 Hz Headphones SW1 Band fL(2.3 MHz): L7
Socket Coverage fH(7.3 MHz): TC5
(Load resistance:
SW1 fL(2.6 MHz): L4
32 ohms)
Tracking fH(6 MHz): TC6
SW2 Band fL(7.3 MHz): L8
Coverage fH(22 MHz): TC7
DECK SECTION SW2 fL(8.5 MHz): L5
• Bias Oscillation Tracking fH(19 MHz): TC8
• Beat Cancel Switch: C
Adjustment Point Specified value Instrument
Connection
• VCO Frequency
L301 100 kHz + 4 kHz Pin 1 of CNS102
Adjustment Specified value Instrument Connection
Point
Specified Value VR1 76 kHz ± 200 Hz Pin 13, Pin 21 and ground
Beat Cancel A: 104 ± 4 kHz of IC2
B: 94 ± 4 kHz
C: 100 ± 4 kHz Note:
After preparing the test circuit shown in Fig. 7, connect the Pin
• Playback Amplifier Sensitivity Check 13, Pin 21 and ground of the IC2 with the test circuit, and
measure the value.
Test tape Specified value Instrument Connection
MTT-118 2.5 V ± 3 dB Speaker terminal Pin 13 of IC2 Pin 21 of IC2
(Load resistance: 8 ohms)
D
G FET: 2SK212
(or Other 2SK Type FET.)
10 pF
S
1M ohm TO FREQUENCY
0.1 µF
10K ohm COUNTER
Figure 7 VCO FREQUENCY TEST CIRCUIT
–7–

GX-CD1200W
SW103
SW1
SW401
TC6
FM TRACKING SW1
fH TRACKING fH
TC5 L7
MW
SW1 BAND fH TRACKING fH
COVERAGE fL TC3
TC4 MW BAND
TC7 L8
COVERAGE fH
SW2 BAND fH fH FM BAND
COVERAGE fL L2 TC2 TC1 fL COVERAGE
MW BAND
COVERAGE fL L6 FM TC8
TRACKING fL L1
IC1 fH SW2
CF1 fL TRACKING
FM IF
AM IF
L9 L5
L11
CF3 SW1
CF2 L4
12 9 1 TRACKING fL
IC2
13 21 24
VCO
MW
L10 L3 TRACKING fL
VR1 FM DETECTION
MAIN PWB
MAIN PWB
CNP103
IC502 Q603
TAPE SPEED
VR102
CNP501
SPEAKER TERMINALS
Figure 8 ADJUSTMENT POINTS
–8–

GX-CD1200W
CD SECTION
Since this CD system incorporates the following automatic adjustment function, when the pickup is replaced, it is not necessary
to reajust it.
Since this CD unit does not need adjustment, the combination of PWB and laser pickup unit is not restricted.
TEST MODE
Start While holding down the "PLAY" button, move the FUNCTION/POWER switch to "CD".
(To serial No.006XXXXX)
While holding down the "STOP" button, move the FUNCTION/POWER switch to "CD".
(From serial No.007XXXXX)
Note 1. When the CD LID switch is in the OFF position, (CD LID is open) the unit will be able to enter the test mode.
However, can use the "UP/CUE" and "DOWN/REVIEW" button only.
2. You can only move the pickup.
3. The LCD display should be the same as it is for normal CD operations.
The use of the "UP/CUE" button will move the pickup to the outermost position.
Operation
The use of the "DOWN/REVIEW" button will move the pickup to the innermost position.
LCD MODE
Start After connecting of the 10kΩ resistor between IC802 27 pin and GND and holding down the "PLAY" button, move
the FUNCTION/POWER switch to "CD".
Display
LASER LIGHTING CONFIRMATION

1. Remove the front cabinet according to the disassembly method.
2. Short the TP of the Figure 9 to turn on the CD LID SW 810.
3. While holding down the "PLAY" button, move the FUNCTION/POWER switch to "CD".
4. Open the CD LID and press the PLAY button. The laser lights up for a few seconds. (At this time, the pickup lens moves up
and down and adjusts the focus to check if there is a disc or not.)
CD CONTROL PWB-C2
R847 R848
SW802 SW804
R849
STOP REVIEW/
TRACK DOWN
SW801 SW803
PLAY/ FW801 LCD801 CUE/
PAUSE 10 1 8 7 6 5 4 3 2 1 TRACK UP
SWITCH PWB-C3
13 16 17 4 14 15 CD SERVO PWB-C1
C851
C846
SW810 L802
TP OPEN/CLOSE C853 C849
C855
1 2 3 Q803
R822 L803 R857
FW801 R858
C847
C848
10 1 1 100 R835 C850

2 1 R861 C858 3 2 1 Q804
C824 5 R839
FW1 R846 C844
12 10
95 C852
R844 15 90 R865 C845 R836 11
20 85 81
R863 25 IC802 75 80
R840 1
30 L801 6
70
31 35 C840 5
C825
X801
C823
65
C843
P804
40 4
R821
2 1 60 R832 CNS804
45 55 3
C837 C842
Figure 9
–9–

GX-CD1200W
SW1 fH TC6 SW1

FM SIGNAL MW/SW1 SIGNAL PLAYBACK SIGNAL RECORD SIGNAL TRACKING fL L4 COV
IC1
TA7358AP SW103-B
CF1 FM MODE
FM BAND PASS FM FRONT END R4 R7
6.4V 7 330K
A FILTER
0.9V RF AMP C13
820K
C23 FM STEREO FM MONO Q181
1 2 3 C12 0.022 C22
OSC
220/10 KTC3199 G
MIX
1 0.022 VR1
ROD ANTENNA(253) 3P(CH) GRAPHIC
10KB
R183 EQUALIZE
SW1-A FM 330K
BAND 1.6V 2 3 4 9 6 8 5 0V
C18
C31 C34 R14 VCO
C17 DETECTION 0.0047(ML)
7V
7.1V
1.6V
470P 100K
7.2V
7.2V
SELECTOR FM 10/16 0.022 C181 2.7V
C5 C36
0.0082(ML)
C10 C35 1/50 0.9V
0.001 15P(CH) R8 0.0015
MW C2 R2 R5 3.3/50 R19
3.3/50
SW1 FM 5P(CH) 3.9K R9 15K
33 TC1 100
C33
12K 0.3V
C32
SW2 TRACKING TC2
22P(CH)
N.C. R181
L10 C183
1K
VC1
C4 L1 24 23 22 21 20 19 18 17 16 15 14 13 12 R1
VC2 220P
C11
24P 220
AM IF AM OUT
STB
DET OUT
L2
AM OSC
AM RF
MO/ST
FM DET
AM IN
MPX IN
VCO
+B
FM
IF AD
(CH)
IF AD
OSC. IC2 TP1
FM IF IN
D1 R1
AM MIX
C184
DS1SS133
LA1805
AM/FM
DS1SS133 L9 VCO 220
R-CH
220P
L-CH
GND
FM/AM IF MPX. 76KHZ
D2
R3 AGC
R1 C182 2.7V
47 1 2 3 4 5 6 7 8 9 10 11 1/50
B 10 L11
+B
0.9V
FM IF 1 3 C24 CF3 C38

C8 C41 R182 0.3V
C9 0.022 1 3 455KHz C37 0.012 1/50
0.022 0.022 AM IF 0.012 (ML) 1K R184
SW1-B C7 C6 (ML) 330K
BAND Q182
0.0047 0.0047 2 AM IF C39 C40 R20 KTC3199
SELECTOR CF2 R12 1/50
C25 2 1/50 10 GRAPHIC
FM L3 MW FM IF 0.022 C29 1K EQUALIZ
SW1-D 22/16 R15 R16
MW FM 10K 10K
SW1 BAND
MW SELECTOR
TC4 SW1-F
SW1 FM BAND
L6 MW OSC. R127
SW2 SW2 MW SELECTOR 22K
VC4 +B
SW1-E TC3 SW1
BAND C19
SW2
SELECTOR 330P C21 R13
TC6 FM 5P C30 100 R129 150K +B
C14 (UJ) R18
5P(CH) MW 0.022
SW1-C 2.7K
L7 SW1 OSC.
BAND SW1
L4 SW1 R130 150K
C SELECTOR
FM L3,4 MW/SW1
SW2
C20 FM
R17 R128
L-CH
0.0022 TC5 2.7K CD 22K
BAR ANTENNA TC9
SELECTOR
MW
VC3 MW TUNER
R10 47
SW1-G
SW1 SW1 FM TAPE
BAND
L8 SW2 OSC.
TC8
SW2 FINE SW2 MW SW501-A
R11 SW1 FUNCTION
SELECTOR
TNNING C27 TC7
L5 SW2 47 SELECTOR
SW1-H
0.0047 SW2
BAND
ANTENNA C15 CD
0.022 TUNER R-CH
R354 R353 C26
TAPE
BI804
27K 27K 0.022 C43 C42

220P 0.022 SW501-B
CNS804 R352 FUNCTION
R-CH 47K SELECTOR
6 6
GND(A)
5 5
L-CH R351
4 4
CNP804 A-GND 47K
3 3
D TO CD
SERVO 2 2
D-GND
+8V(SERVO) SW501-C
PWB 1 1 0V(9V) ( ):CD FUNCTION FUNCTION
P13 11-G 1 SW101-F D165 SELECTOR
R165 BAND SELECTOR DS1SS133 +B CD
J151 0V(0V) 2 10K
MIC JACK 3 0V(9V) R166 P R TUNER
Q154 6V +B 560 TAPE
0V 1 7
KRA102M IC151 D164
TA2011S C157
MIC AMP. 1.9V
1/50 DS1SS133
0V
3
MIC AMP. 5
R153 0V(0V) SW103-A C158 C159
DS1SS133
2 4 ( ):HIGH R168 DUBBING

2.2K 1.3V 0V 6 C156 10K 47/25 47/25
0V(0.7V) SPEED/MIC
0.9V 100/10
KTC3199 GR
D163
D156
HIGH R171
MIC AMP.
DS1SS133 D154
R152 0V(0V)
Q153
DS1SS133 33K
0.33/50
4.7K C154 R169 NORMAL

C151
47/10 10K
C155 R172 R170 D158
10/16 MIC 10K 33K DS1SS133
E C152 R154 R161 R177 D162
10/16 560 1M D152 1K
+B DS1SS133 DS1SS133
( ):RECORD
MIC151 R151 R173
BUILT-IN 2.2K 10K +B R174
(0V)
MICROPHONE L103 C137 22K
(0.7V) R100 C160
22mH 0.0015(ML) Q156 150 22/16
KTC3199 GR 0V
LINE AMP. R111
R135 10K 22K
C131
R115
C113
R101
120P +B
C103
470P
R117 C119
680
100
C101 4.7/50
330K 0.033
R121 10K
470P C111 9V 0V
TAPE2 0.015 R109 (ML)
4.7/50
330/10
3 2
2.2/50
PLAYBACK HEAD (ML) 6.8K

C115
Q601
C128
C123
C127
10/16
R119
C117
SW504-A 0.01 KRC102M 0V

TAPE2 DIRECTION 100 R133 1
47/10
C109
C105 R107 82K

CNP101
CNS101
330P 10K
A C107
F SIDE-A 330P R105 R113 C121 C125
RECORD/PLAY AMP.
L-CH 180K 120K 330P 4.7/50

SIDE-B B 24 23 22 21 20 19 18 17 16 15 14 13 R131
1 1
1.2K
IC101 TA8189N
CH2/A CH2/B NF MATAL PRE A/B VCC REC REC REC ALC
2 2 OUT OUT OUT NF IN
3 3
A SW101-A~D
MATAL PRE MIX REC REC REC
SIDE-A RECORD/ CH1/A CH1/B NF OUT OUT OUT GND1 M/N OUT NF IN GND
R-CH PLAYBACK R132
B 1 2 3 4 5 6 7 8 9 10 11 12
SIDE-B C108 1.2K
R106 C122
22/16
C129
R P R P 330P 180K R122 R114 330P

R108 120K
47/10
10K C126
C110
SW504-B SW101-D SW101-C C106 10K 4.7/50

C133
150P
TAPE2 DIRECTION
10/16
R134
C118
SW101-B 330P C124

SW101-A 82K
C112 R120 0.01
R P R P
4.7/50
C116
1 1 0.015 R110 R123 100

L-CH (ML)
C104
6.8K
470P
2 2 C102 10K
C120
C134 470P R102 C114 R124 R116 R118 0.033
3 3 680 330K (ML)
R-CH 150P 100 4.7/50 10K
G 4 4
C132 120P R136 10K
CNS102
CNP102
R112
BEAT CANCEL
22K
Q301
KTC3203 Y +B Q5
ERASE HEAD L104 BIAS OSC. KT
C138 R301
SW102
TAPE1 22mH 0.0015(ML) ( ):RECORD SW

R302 R 330
RECORD/PLAYBACK HEAD (3V)
R306 R305 100
47 27K (0.7V) R511
0.0015
C B A P
C301 100/10
C305
10K
(ML)
L301 C303 SW101-E

(0.1V) RECORD/
C307 BIAS OSC. 0.0056
150P C306 PLAYBACK +B
(ML) C302
390P C304 0.0022 R304
0.022 R303
(ML) 10 100
MAIN PWB-A1/VOLUME PWB-A3/FINE TUNING PWB-A4

H
• NOTES ON SCHEMATIC DIAGRAM can be found on page 18.

1 2 3 4 5 6
Figure 10 SCHEMATIC DIAGRAM (1/4)
– 10 –

GX-CD1200W
fH TC6 SW1 BAND fH TC5 MW fH TC4 FM fH TC2 SW2 fH TC8 SW2 BAND fH TC7 MW BAND fH TC3 FM BAND fH TC1
fL L4 COVERAGE fL L7 TRACKING fL L3 TRACKING fL L2 TRACKING fL L5 COVERAGE fL L8 COVERAGE fL L6 COVERAGE fL L1
GRAPHIC EQUALIZER PWB-A2 IC202 LB1403N

LEVER METER DRIVER
R251 C251 9 8 7 5 6 4 3 2 1
Q181 6.8K 1/50
KTC3199 GR
+B C257
GRAPHIC
39K
R257 10K
EQUALIZER 47/25 R255
LED257
R183
LED255
LED253
LED259
330K GRAPHIC 120 C253
X-BASS EQUALIZER C259 0.022
R253
C181 2.7V
C185 0.0039
1/50 VR202 VR203 VR204 VR205 (ML)
1/50 0.9V R203 C203 50K(A) 100K(A) 100K(A) 100K(A)
R187 1/50
3.9K 2.2K (100Hz) (500Hz) (2KHz) (10KHz) C255 R259
10/16 120
0.3V
1 R205
C183 R185
R207
220P 4.7K
4.7K
220
IC203 LB1403N
LEVER METER DRIVER
R186
C221 4.7/50
C184 R201 C201 R211 C209 C205 R256 9 8 7 5 6 4 3 2 1
220P 220 C217 0.01 120
R188 1K 4.7/50 1K C213 0.082
3.9K 0.47/50 (ML) (ML) C252
C182 0.33/50 1/50
2.7V
0.039
0.0015
C219
0.0056
1/50
(ML)
C211
C207
470P
C180 +B
C215
(ML)
0.9V
R258 10K
(ML)
R254 39K
100/10 R252
LED254
R200
LED256
LED258
LED260
C186 6.8K
EQUALIZER
330 C260
R182 0.3V
BA3822LS
1/50 C254
GRAPHIC
23 21 19 17 15 13 11 9 7 5 3 1 0.0039
K R184 C200 (ML) 0.022
5.9V
5.9V
3.2V
6.5V
6.5V
5.9V
6.5V
6.5V
5.9V
2.6V
4.4V
6.9V
330K
IC201
Q182 100/10
4.4V
3.2V
2.6V
5.9V
6.5V
5.9V
6.5V
5.9V
6.5V
5.9V
C256
6.5V
R260
KTC3199 GR 0V 10/16 120
GRAPHIC 24 22 20 18 16 14 12 10 8 6 4 2
+B
EQUALIZER R518 1K LED501 LED501,502
C208
470P
0.0015
0.0056
0.039
C220
R180
C212
C216
POWER DIRECTION
(ML)
(ML)
(ML)
560 R202
1K R519 LED502
1K
R127 C206
22K C202 C210 C218
C222 0.01 0.082 C214 0.47/50 A : 0.8V
4.7/50 (ML) (ML) 0.33/50 R520 B : 0.2V
4.7/50 10K A : 0V
B : 0.7V Q505
LED401 SURRUND
R212
R208
3.3K
KTC3199 GR
+B 1K LED CONTROL
R521 0V
R204 C204 10K
2.2K 1/50
R128
VR205 VR204 VR203 VR202
STEREO
LED1
22K R206 100K(B) 100K(B) 100K(B) 50K(B)
3.3K (10KHz) (2KHz) (500Hz) (100Hz)
X-BASS GRAPHIC
EQUALIZER
+B
+B R440
470
SW401
+B
SURROUND
R411
330
IC401
C403 KIA4558P
10/16 3.8V 7.5V 8 OPE AMP.
C409 R415
5 3.8V 1/50 3.3K VOLUME SP403
IC402
TERMINALS
7 TWEETER
LA4663
50K(B)
VR401
SPEAKER
3.8V C413 8 Ohm
POWER AMP.
CNP501
6 R425 C419
47/10
C411
C425
0.0068(ML)
0.001 4.7/50 6.9V

R409 (ML) 1K 0V +OUT1 0.1(ML) L-CH
R403 12K 2 14
10K R433
POWER MUTE
R405 R407 R417

C401
R412 C415 0V SP401

KTC3199 GR
2.7K 12K 22K R427 0V 2.2

R401 10K 0.15 L-CH 13 WOOFER
100K (ML) 4.7K R441
15K 6
+ L-CH 8 Ohm
6.9V
0.0033
C407 R413 0.6V -OUT1 R435

R419 –
0.0033 C405
Q403
C423 12
(ML)
4.7/50 10K 3.3K C418 0V C427 2.2

22/16 10/16 0.1(ML)
0V
R429
3 C426 –
C412 6.9V R-CH SP402
C406
R420 0.1(ML) R434

(ML)
C408 100K 0V +OUT2

47/10 3.3K 14.3V 9 + WOOFER
R442
4.7/50 0.6V 2.2 8 Ohm

15K
R402
100K R406 R418 C416
R428 C424 1 R-CH
0V
2.7K R408 0.15 VR401 C420 47/25 10
12K 22K 4.7K 0V R-CH
+B (ML) 50K(B) 4.7/50 6.9V
0.0068(ML)
R404 R410 0V -OUT2 R436

10K C414 4 11 SP404
12K 0.001 Q404 C428 2.2
C410 R426 TWEETER
KTC3199 GR 0.1(ML)
C402
3.8V 2 3.8V 1/50 (ML) 1K 8 Ohm

C404 POWER MUTE 5 7 8
10/16 1 6.4V 15V 15V
3.8V R416 VOLUME
3 IC401 3.3K R431 C429
KIA4558P 27K 10/16
4 C433
0V OPE AMP. R437
0.022 120
+B 9V OUT IC501 15V +B
3 KA7809AP 1 C430
C505 C513 10/16 R438 J401
47/16 C506 2 IN
0.022 1/50 120 HEADPHONES JACK
0V
Q602 C510
KRA102 M 0V 3300/25 SW601
SWITCHING3
15V
2 POWER PWB-A7 VOLTAGE SELECTOR
1 15V
1 1 AC110V-127V
Q603 2 2
KTD2058 Y
CNS601
CNP601
+B
VOLTAGE AC220V-240V
REGULATOR R601
7.5V 270 T601
F601 POWER SO601
R602 C601 D651 T4A L 250V
C604 8.1V 100 SW501-D TS4B03GM TRANSFORMER AC SOCKET
C603 0.022
220/10 0.022 FUNCTION AC110V-127V/
SELECTOR C652 AC220V-240V,
C651 50/60Hz
C602 DZ601 0.022 0.022
100/10 DZ8.2BSB M501
CNP103
+ MOTOR
OUT IN
9V IC502 15V – C653 C654
3 KA7809P 1 0.022 0.022
C508
100/16 2
C514
1/50
B
A
M
C509 1 1
0.022 0V 2 2
( ):HIGH SPEED R513 L501
10K 47µH 8.5V(8.5V) 3 3 SW901
0.7V(0V) TAPE1 MAIN
Q504 4 4
Q503 R514 KTA1271 Y 5 5 SW902
Q502 KTC3199 GR 100K SWITCHING TAPE2 MAIN
SWITCHING 6 6
KTC3199 GR 7.9V
SWITCHING (7.9V) R516 7 7 SW903 TERMINAL B
0V(7.9V)
8.5V
(6.3V)
3.6K
8 8 TAPE2 PLAY
PWB-A6 TERMINAL A
0V(0.7V) 0.7V
(0V)
VR102
R515 9 9
PWB-A5
R511 470 SW904
120 BATTERYS DC 15V
10K R512 C511 TAPE SPEED CNS103 TAPE2 ["D" SIZE (UM/SUM-1,
10K 0.022 DIRECTION R20 or HP2) battery x 10]
0V(0V) 0V(0V)
IC501,502:VOLTAGE REGULATOR
7 8 9 10 11 12

– 11 –

GX-CD1200W
FW802 ( ):STOP
SW810
OPEN/CLOSE R802 IC801
Q801 2.2K TA2109F
SWITCH PWB-C3 KTA1266 GR SERVO PRE AMP.
SWITCHING
0.2V(1.5V) 4.3V(5V) R801 +B C825
CNS802
VCC +5V 22 47/10
BI802
C817 C815 C816
C802 3.6V 100/10 47/10 0.022 R804
LD C3A
0.022 (4.4V) C8
68K 47
B MON
7 7 7 2.1V
RFN 24
C2A 6 6 6 R896 5V
1 VCC
2P(CH)
56K R805
GND 23
C804
E
E
5 5 5 39K
0V
A A R895 IC801
4 4 4 68K R806
1.6V
B
3 3
B R893 2.1V (0.3V) 2.7K
3 68K 2 FNI
F F R892 2.1V RFO 22
2 2 2 3 FPI C820
56K 8 0.1
C C R891 2.1V
1 1 1 68K (2.1V) 4 TPI (ML) R807
0V
2.1V AGCI 21 1K
2/1VCC (2.1V) 5 TNI 0V
RFGC 20
R894 0.18V
CNS801
6 MDI
68K (0V)
9
BI801
2.2V C819
C C4A 3.6V
(4.4V) 7 LDO
RFGO
19 0.1(ML)
47/10
C832
2.1V
C818
RFIS
18 56P
R- TR+ 3.2V +B
2.5V (1.1)
1 1 1 (0.3V) 8 SEL
RFRP 17
TR+ R+
2
TR- 2.8V
9
10
2 2 TEB
VRO 16
2.1V
FO+ F+ FC+ 4.3V
3 3 3 10 2VRO C801
15
R811
FEN
47/10
C821
0.1
22K
R803
F- FC- 2.1V 2.1V
4 4 4 11
82K
TEN
G GND 2.1V
FO- 5 5 5 14
2.1V FEO C863 C854 R
PD PD
TR- 6 6 6 12 TEO SBAD 13 2.0V 47/10 0.0068
(1.1V)
VR1A VR VR
7 7 7
LD LD +B R
D 8 8 8
C813 C814 C822
47/10 0.047 0.047
PICK-UP UNIT C841
0.047
0.047
C842
47/10
C843
CNS803
CNP803
M
BI803
M802
SPINDLE
MOTOR – C834
SP+ DM+
470P
SP-
6 6 6
DM-
2 C835
5 5 5 470P
+ SL+
4 4 4
FM+ 3 FOO C836
E
M801
SLED
MOTOR M –
SL-
3 3 3
FM-
R853
0.047
(ML)
2.2K
PU-IN SLT+ C837
2 2 2 0.047 (M
GND TRO C838
1 1 1 0.047(M
SW702
+B
C839
SLT-
PICKUP IN C807 0.047(M

2.1V
2.1V
3.3V
3.3V
3.3V
2.1V
7.4V
2.1V
3.3V
2.1V
4.8V
0.047
0V
0V
0V
CD MOTOR PWB-B N.C. N.C. N.C.

30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 5V
VO4-
VO3-
GND
GND
VCC
VREF
VO4+
VO3+
VIN4
GND
VG3
CD
VG4
VIN3
RES
To serial From serial

SERIAL NO. No.00404990 No.00504991 IC803 LA6541D
FOCUS/TRACKING/SPIN/SLED
REG OUT
REG IN
F
VO1+
VO2+
PICK-UP UNIT 92LHPC1LASY 92LHPC1LXASY

MT
VO1-
VO2-
VIN1
GND
GND
GND
VIN2
VCC
VG1
VG2
N.C.
BI802/CNS802 QCNWN0027BGZZ QCNWN0032BGZZ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 6.7V C89
2.1V
3.4V
3.3V
2.1V
5V
+B 220
7.4V
3.6V
2.1V
C801 VCQYKA1HM103K NOT USED

2.2V
0.9V
0V
0V
0V
3V
R802 VRD-ST2CD222J NOT USED

R851
5V(5V)
2.2K
R852
220/10
2.2K
6.8V
R891 NOT USED VRD-ST2CD683J
0.022
(6.8V)
C806
C805
R892 JUMPER VRD-ST2CD563J Q802

7.4V(7.5V)
+B KTA1271 Y
R893 JUMPER VRD-ST2CD683J VOLTAGE
R894 NOT USED VRD-ST2CD683J REGULATOR
R895 JUMPER VRD-ST2CD683J

G R896 JUMPER VRD-ST2CD563J FMO
DMO
+B
+B
CD SERVO PWB-C1
• NOTES ON SCHEMATIC DIAGRAM can be found on page 18.

1 2 3 4 5 6
– 12 –

GX-CD1200W
C825 +B
47/10
+B
C826 +B +B
47P
C823
R820 R824 0.022
2.5V
1.7V
0.4V
2.5V
5V
0V
5V
0V
0V
0V
0V
0V
0V
0V
0V
47K 10K 2.1V
4.2V
0V
5V
N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. L803
R826 2.1V 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
220K 10µH
TEST0
TEST1
SBOK
SPDA
SPCK
COFS
/HSO
SBSY
DOUT
PDO
VSS1
VDD1
TMAX
TEST5
TEST4
TEST3
TEST2
P2VREF
C827
R827 0.015 2.1V R821
15K (ML) 51 LPFN 12 13 0V PUSEL2 30 22K
2.1V
52 LPFO 5V PU IN 29
2.1V
53 PVREF 0V(5V) MUTE 28
C830 1.5V
54 VCOF 5V ADIN2 27
0.01(ML)
0V
55 AVSS 5V ADIN1 26
R863
C828 3.3K
2.1V
0.0027 56 SLCO 0V P3-0 25
47/10
C832
C829 2.1V
57 P1-3
0.0047 RFI 5V 24
+B 5V R844
58 AVDD 0V P1-2 23 3.3K
R828 10K 2.1V
59 RFCT 0V P1-1 22 N.C.
R846
2.1V C824
60 RFZI 0V P1-0 21 N.C.
330
C833 2.7V 0.1(ML)
61 RFRP 0V MVSS1 20
0.033 (ML)
2.3V
62 FEI 5V MVDD1 19
2.9V
63 SBAD
5 0V P8-3 18
C863 C854 R812 1K 2.1V
64 TEI
7 0V CD LID 17 SW801
7/10 0.0068
2.1V
65
6 IC802 SW
16 R861 PLAY/ R847 R848 R849
TEZI
TC9457F0
0V CDSEL1
3.3K PAUSE 1K 2.2K 6.8K
R829 3.3K 2.1V
66 FOO 0V CDSEL0 15
REVIEW/
1 SERVO/SIGNAL
SW802
TRACK UP
R830 10K
STOP
TRACK
2.1V
SW803
R822
DOWN
SW804
67 TRO 2.5V SEG14 14 N.C.
11 CONTROL 22K
CUE/
2.1V
68 VREF 2.5V SEG13 13 N.C.
C841 R831 3.3K 2.1V
69 RFGC 2.5V SEG12 12 N.C.
.047 R832 3.3K 2.1V
70 TEBC 2.5V SEG11 11 N.C. L802 LCD801
0.047
C842
R833 3.3K 2.1V

71 FMO 2.5V SEG10 10 N.C. 10µH
R834 3.3K 2.1V
72
15
DMO 2.5V SEG9 9 N.C.
+B 4.1V
73 2VREF
14 2.5V SEG8 8 N.C.
C840 2.5V
74 SEL 2.5V SEG7 7 N.C.
C834
470P
0.047
5V
75
4
VDD2 2.5V SEG6 6 N.C.
R840 0V
76 8 7 6 5 4 3 2 1
835 10 VSS2 2.5V SEG5 5
70P 0V
77 XVSS 2.5V SEG4 4
836 2.1V
047 1 78 XI 2.5V SEG3 3
L) C837 2.6V
79
2 XO 2.5V SEG2 2
0.047 (ML) 5V
C838 80 XVDD
17 16 2.5V SEG1 1 N.C.
R865
0.047(ML) XL801 3
1K
RESET
DVSR
DVRR
DVDD
COM1
COM2
COM4
COM3
MVDD
DVRL
DVSL
MVSS
16.93 MHz
HOLD
INTR
MXO
C839
RO
MXI
LO
0.047(ML) N.C. N.C.

C845
0.047 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
0V
C848 2.5V
22/16 2.3V
4.7V
2.4V
C847 2.5V
22/16 0V
0V
0V
5V
0V
5V
N.C. N.C.
C860
5V
2.3V
2.3V
2.3V
2.3V
5V
0.3V
0V
0.0015
+B
C844
100/10
C894 R836 R835 FW801
0.022 15K 15K
+B C855 Q804 +B CD CONTROL PWB-C2
C893 L801 C853 C850 C849 0.022 KRC102M
220/10 0.82µH 0.022 120P 120P C846 R839 MUTING
2.2/50 47K 0V 3
2 0V(5V)
C852 C851 1 0V
3.3/50 3.3/50
C858
R858 R857 0.022 0V 3 0V(5V)
5.6K 5.6K 2 Q803 CNP804
1 0V KRC102M R-CH
MUTING 6
GND(A)
5
C859 L-CH
0.0027 4
A-GND CNS804
3
D-GND
FROM MAIN PWB
+B 2 P10 1-D
B+
1
• The numbers 1 to 17 are waveform numbers shown in page 19.
7 8 9 10 11 12

– 13 –

GX-CD1200W
CNP501 TO CD SERVO PWB

P17 12-D
SPEAKER
CNP804
A MAIN PWB-A1 TERMINALS SW102
BEAT CANCEL
CNS804 1 2 3 4 5 6 C B A
C306
C301
R304
L301
C307
R306 C304
C305
1 6
Q301
BI804
E
C
B
Q503
Q502
C601
C302
B
C303
R305
C511
CK129
R512
1 3 DZ601
Q601
E
C607
E 2 2 R602
Q602
R601
R302
C C
C608
B 3 1
Q504
VR102 C B B
E
C602
C603
C604
R352
R513
R514
R516
R351
R515
IC502 Q603 R111
C510
R131
C508
R119
C125
C123
C113
C124
3 2 1
C135
E C B
L501
C126
C127
Q404 Q403
C509
R428
R117
B B R427 C514 R100 R132
C121
C122
R118
R429
R116
C C C C128
C424
R120
CNP103
R115
C118
E E C418 C513
R121
D158 1 2 3 4 5 6 7 8 9
R441
C120
C136
C419
C160
R174 12 13
1
C115
2 R171
R122
R136
R442 10 15
R123
C138
R112
3
R113
C129
R114
D156
C116
C512 C506
4
IC101
C433
IC402
5 C505 IC501
6 C420 R
R425
C423
7 R108 R107 C
8 R426 3 2 1 C114
5 20
9 R106 R105 D152
10 R134 R110 C108 C107
R124
11 R431
R133 1 24 R
R184
12 4 C186 C112 C106

R433
B
R435
13 C105 C1
C184
C185 R104 R102

14 C
C182
CNP601 R511 C104 C103 R101 R1

FW1 E L104 C109
C102 C101
Q182
C181
1 1 B C110
C183
D R183
L103
CNS601 C427 C C132
C131
R182
2 3 2 1
C180
FROM E
R186
R436
R188
R187
POWER CNP101
C426
D162
Q181 SW101
R185
R434
R180
PWB C425
P16 5-F
R177 C
A B D E F
R130 C134
R181
C428 C133 4 3 2 1
R173
R128 CNP102
R301
D154
WH BK
R127
R170 D163
R168 D164
R165
R169 B C157 C158 R408 C411
C405 R411
IC401
R412
E C D165 4 5
R413
Q153
R417
C156 R407
C412
E
R129
C408
1
C159
R410
C410
C407
Q154
2 R166 R405
R406
C154 R409
3 1 8 R403
R404
C430 7 6 5 4 3 2 1
C404
R438
IC151 R418
R153
C406
C409
R402
C155
C401
C402
C403 R415
R401
R154 SW501
R437
C429 R161 R416
BK FUNCTION SELECTOR
R151
J401 A
C151
B
HEADPHONES JACK
C152 WH
D C
R152 VOLUME SW40
SURRO
F
WH J151
MIC JACK PWB-A3
BK GL
CD/LINE
RADIO
TAPE
VR401
MIC 151 VOLUME
BUILT-IN
B
MICROPHONE
C413
A
C414
E
R521
C415 1 2
Q505
C C416
R520
B
C252
C210
R203
C208
R205
LED502 R420
R419
C212
LED501
R256
R208
C214
R519
C216
C206
C254
R518
R206
C260
C220
C222
R252
LED259 R259
G
C218
VR205
VR203
VR204
R204 4 1
1 LED253 LED258
LED255
LED260
C257
5
R255
C207
C204 FW1
IC201
10
VR202
LED257
C219
C203
R212
15
C215
C221
C211
20
C205
24 IC202
C259
R201
C217
1 2 3 4 5 6 7 8 9
C202
C209
R253
R207
C200 C213 C253

C255 R257
C251
C201
R202
R211
H R200
R251
1 2 3 4 5 6
Figure 14 WIRING SIDE OF P.W.BOARD (1/4)
– 14 –

GX-CD1200W
W102
AT CANCEL
C B A
ROD ANTENNA
SPRING (249)
COLOR TABLE
L301 BR BROWN
ROD
RD(R) RED
C305
ANTENNA (253)
WH OR ORANGE
YL YELLOW
R7
BK
GR GREEN
C34
L10
VR1
L3 BL BLUE
C32
C31
R9
C35
C33
MW
R352 R354
VL VIOLET
R351 R353
R19
TP1 R8 GY GRAY
C18
C17
R131
R119
C22
C23
C125
C123
C119
C36 13 24
15 20 WH(W) WHITE
27 IC2
C29
10 5
C43 BK BLACK
R117
R16 12 1
C117
C121
C40 C24 L4
CF3 CF2 PK PINK
R115
R18
Q156
SW1
1 2 3 3 2 1
R121
R17 C39 L11

R3
C38
C160
E
R15 R5
C115
C L9
R12 D1 L3,4
R113
B
C37
C15 MW/SW1
C41
C25
BAR ANTENNA
R14
R135 L5
R20
R107 C137
R105 TAPE 1
D152 C13
R172 D2 C9
C107 ERASE RECORD/PLAYBACK
R109 C2 C8
IC1 R4
HERAD HEAD
C105 C111 CF1
3 R101 R103 1 2 3 1 2 3 4 5 6 7 8 9
C109 L6 R2 TC8
C10
C5
L103
C12
C131
R1
R303
1 C7
101 C6 L1
C21
VC1
L2
C11
TC2
RD
TC1
R13
F L8
TC7
C28
BK
C4
WH
VC2 VC1
R173
2
FINE TUNING
R301
VC4 VC3
R11
C16
C26 L7
PWB-A4
R440
TC4 TC3
TC5
GY
C405 R411
R412
C14
R413
R417
FW2
C412
C20 TC6
C19
C27
409 C42 E F C D
R415 C30 WH
RD
BK
BK
TC9
CNS102
H G B A
4
3
2
1
B
ON
A R10
SW401 SW1
SW103 BAND
SURROUND OFF DUBBING SPEED/
MIC/FM MODE SELECTOR
NORMAL
MIC HIGH
FM MW SW1 SW2
FM MONO FM STEREO CNS103
R254 BR
RD 1
C413 OR 2
R258 YL 3
GR 4
C415 1 2 3 4 5 6 7 8 9 5
BL
IC203 VL 6
7
C252
GR
8
R419
LED401
YL WH
9
LED1
R256
C256
YL
C254
B A TAPE 2
C260
A B +-
R252
SW504
TAPE1 HEAD FLEXIBLE PLAYBACK
R260
LED258 DIRECTION PWB HEAD

LED254
LED256
LED260
SW503
TAPE2
PLAY B
M501 C A
SW501A SW502
TAPE2 TAPE1 TAPE GR
MAIN MAIN MOTOR
GRAPHIC BK RD WH
CNS101
RD
EQUALIZER GY
3
2
WH
PWB-A2 1
7 8 9 10 11 12

– 15 –

GX-CD1200W
A
SO601
AC SOCKET
AC110V-127V/
AC220V-240V, TERMINAL A
50/60Hz PWB-A5
SW601 (251)
VOLTAGE SELECTOR
AC220V-240V AC110V-127V (250)
BATTERYS
OR
DC15V
["D" SIZE (UM / SUM-1,
R20 or HP2) battery x 10]
RD
TERMINAL B (251)
T601 PWB-A6
POWER
TRANSFORMER
D
BK
WH
BL
(237)
RD
WH
OR
COLOR TABLE
CNS601
BR BROWN
F
RD
1 TO MAIN PWB
RD(R) RED
BK CNP601
2
OR ORANGE P14 1-D
BK
YL YELLOW
T4A L 250V
F601
GR GREEN
C653
BL BLUE
C652
VL VIOLET
GY GRAY
C654
G
WH(W) WHITE
C651
BK BLACK
PK PINK D651
POWER
PWB-A7
1 2 3 4 5 6
– 16 –

GX-CD1200W
CD CONTROL PWB-C2
R847 R848
SW802 SW804
R849
STOP REVIEW/
TRACK DOWN
SW801 SW803
PLAY/ FW801 LCD801 CUE/
PAUSE 10 1 8 7 6 5 4 3 2 1 TRACK UP
SWITCH PWB-C3
13 16 17 4 14 15 CD SERVO PWB-C1
C851
C846
SW810 L802
OPEN/CLOSE C853 C849
C855
1 2 3 Q803
R822 L803 R857
FW801 R858
C847
C848
10 1 1 100 R835 C850
2 1 R861 C858 3 2 1 Q804
C824 5 R839
FW1 R846 C844
12 10 95 C852
R844 15 90 R865 C845 R836 11
20 85 81
R863 25 IC802 75 80
R840 1
30 L801 6
70
31 35 C840 5
C825
X801
C823
65
C843
CNP804
40 4
R821
2 1 60 R832 CNS804
45 55 3
FW1 C837 C842 2 FROM
C832 MAIN PWB
1
R834
R831
R833
R828
R830
R824
50 51 P14 5-A
C854
BI803
R820
C801
C828
R827
C826
C830 C829 C833 9

R829
C827
C841
R826
C838 C819
C863 C839 C821
R802
C836
C835
R807 C818
C834
R851 R852 R805

C820 R803
1 R806
C894
7
C893
B WH
BI802
5 10 15 C822 7
C 13 WH
IC803 Q801 24 20 15 C813 6
C817
C804 WH
R812
E
C814
5
C802
25 20 E IC801 WH
C816
30 16 Q802 5 10 4
C
R811 WH
R804
3
R853
C815
12 WH 2
B 1
1 BK 1
R801
R891 R896 R892 10

BI801
1 8 R894 R893
C805
C806
C807
R895
BR
BK
BK
BK
BK
BK
BK
BK
3 2 5 7 6 8 COLOR TABLE
PICK UP UNIT
1 2 3 4 5 6 7 8 BR BROWN
R D (R ) RED
CNS801 OR ORANGE
YL YELLOW
CD MOTOR PWB-B GR GREEN
BL BLUE
+ VL VIOLET
M801
SLED MOTOR GY GRAY
W H (W ) WHITE
7 6 5 4 3 2 1
- BK BLACK
CNS803
CNP803
F0027AW
PK PINK
BR 1 1 8 7 6 5 4 3 2 1
GY 2 2
GY 3 3
GY 4 4 SW702
GY 5 5 PICKUP IN
GY 6 6 To serial From serial
+ SERIAL NO. No.00404990 No.00504991
- PICK-UP UNIT 92LHPC1LASY 92LHPC1LXASY
M802 BI802/CNS802 QCNWN0027BGZZ QCNWN0032BGZZ
SPINDLE MOTOR
C801 VCQYKA1HM103K NOT USED
R802 VRD-ST2CD222J NOT USED
• The numbers 1 to 17 are waveform numbers shown in page 19.
7 8 9 10 11 12

– 17 –

GX-CD1200W
NOTES ON SCHEMATIC DIAGRAM
• Resistor:
To differentiate the units of resistors, The symbol as K and
REF. NO. DESCRIPTION POSITION
M are used: the symbol K means 1000 ohm and the symbol
M means 1000 kohm and the resistor without any symbol SW1 BAND SELECTOR FM
is an ohm resistor. The resistor designated “Fusible” is a SW101 RECORD/PLAYBACK PLAYBACK
fuse type resistor.
SW102 BEAT CANCEL A
• Capacitor:
To indicate the unit of capacitor, a symbol P is used: this SW103 DUBBING SPEED/MIC/ MIC/FM MONO
symbol P means pico-farad and the unit of the capacitor FM MODE
without such a symbol is microfarad. As to electrolytic SW401 SURROUND ON
capacitor, the expression “capacitance/withstand voltage”
SW501 FUNCTION SELECTOR CD/LINE
is used.
(CH),(RH),(UJ): Temperature compensation SW601 VOLTAGE SELECTOR AC220-240V
(ML): Mylar type SW702 PICKUP IN OFF
(S): Styrol type
SW902 TAPE 2 MAIN OFF
• The indicated voltage in each section is the one measured
by Digital Multimeter between such a section and the SW901 TAPE 1 MAIN OFF
chassis with no signal given. SW903 TAPE 2 PLAY OFF
• Schematic diagram and Wiring Side of P.W. Board for this
SW904 TAPE 2 DIRECTION A
model are subject to change for improvement without prior
notice.
• Parts marked with “ ” ( ) are important for
FRONT
maintaining the safety of the set. Be sure to replace these VIEW
parts with specified ones for maintaining the safety and
performance of the set. FRONT
VIEW
E C B E C B
KTD2058 Y KTA1266 GR 333ID213

KTA1271 Y
KTC3199 GR
KTC3203 Y
KRA102 M
Figure 18 TYPES OF TRANSISTOR AND LED
VOLTAGE
IC2 (LA1805)
PIN 1 2 3 4 5 6 7 8 9 10 11 12
FM 1.6V 1.6V 7.2V 0.5V 1.6V 0V 7.6V 0V 2.3V 2.3V 6.5V 0.9V
MW/SW 1.6V 1.6V 8V 0.8V 1.6V 0V 7.6V 0V 2.4V 2.4V 8V 0.9V
PIN 13 14 15 16 17 18 19 20 21 22 23 24
FM 1V 2.2V 1V 1.7V 1.6V 1.6V 0.4V 7.2V 7.2V 0.5V 1.6V 1.4V
MW/SW 0V 1.8V 1.5V 1.7V 1.7V 1.6V 0.7V 8V 8V 1.6V 1.6V 1.6V
IC101 (TA8189N)
PIN 1 2 3 4 5 6 7 8 9 10 11 12
PLAY 0V 0V 1.3V 1.4V 1.4V 1.3V 0V 0V 1.8V 1.3V 0V 0V
REC 0V 0V 1.3V 1.4V 1.4V 1.3V 0V 0V 1.8V 1.3V 0V 0V
PIN 13 14 15 16 17 18 19 20 21 22 23 24
PLAY 0.9V 0V 1.3V 1.8V 1.4V 7.4V 1.4V 1.4V 1.4V 1.3V 0V 0V
REC 0.9V 0V 1.3V 1.8V 1.4V 7.4V 0V 1.4V 1.4V 1.3V 0V 0V
IC202/203 (LB1403N)
PIN 1 2 3 4 5 6 7 8 9
LED OFF 7.7V 7.7V 7.7V 7.7V 0V 7.7V 0V 0V 8.6V
LED ON 1V 1V 1V 1V 0V 1V 2.4V 0V 8.6V
– 18 –

GX-CD1200W
WAVEFORMS OF CD CIRCUIT
NO DISC FOCUS SEARCH STOP PLAY
1 FOO 1 12 TMAX 1
IC802 66pin IC802 50pin
2 FO+ 2 13 SBOK 2
3 FO- 3 14 DMO 3
FOCUS SEARCH TOC IL STOP PLAY
4 SEL 1 6 TEI 1
5 FEI 2 11 TRO 2
6 TEI 3 15 FMO 3
STOP PLAY CUE
5 FEI 1 6 TEI 1
7 SBAD 2 11 TRO 2
8 RFO 3 15 FMO 3
STOP PLAY REVIEW
5 FEI 1 6 TEI 1
9 RFGO 2 11 TRO 2
10 RFRP 3 15 FMO 3
STOP PLAY TCD-782 TNO-02 PLAYBACK
6 TEI 1 16 LO 1
11 TRO 2
IC802 67pin
17 RO 2
7 SBAD 3 IC802 82pin
IC802 63pin
– 19 –

GX-CD1200W
TROUBLESHOOTING (CD SECTION)
When the CD does not function
When the CD section does not operate when the objective lens of the optical pickup is dirty, this section may not operate. Clean
the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check
the following items.
Remove the cabinet and follow the troubleshooting instructions.
"Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup
lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below."
Turn the power off.

Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.
Dust gradually accumulates on the objective lens during use, and it may degrade performance.
To avoid this problem, use a cleaning disc designed for CD optical pickup lenses.
HOW TO USE
1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has
the mark next to it.
2. Place the CD cleaner disc onto the CD disc tray with the brush side down, then press the play button.
3. You will hear music for about 20 seconds and the CD player will automatically stop. If it continues to turn, press the stop button.
CAUTION
The CD lens cleaner should be effective for 30 - 50 operations, however if the brushes become worn out earlier then please
replace the cleaner disc.
If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth.
Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the event of this happening then drink and / or
rinse with clean water and seek medical advice.
The CD cleaner disc must not be used on car CD player or on computer CD-ROM drives.
All rights reserved. Unauthorized duplicating, broadcasting and renting product is prohibited by law.
Cleaning Liquid Cleaning Disc

PARTS CODE:
UDSKA0004AFZZ
• The CD function will not work.
The CD operating keys don't work.
Check the power supply, 16.93 MHz clock, and reset terminal.
Check the pickup-in switch (SW702) position.
Check the Focus system.
– 20 –

GX-CD1200W
• Laser failure.
Is +7.5V applied to the emiter of Q802 ? Check the PWB pattern of Q603.
No
Yes
Is +5V applied to the collector of Q802 ? Check the peripheral parts of IC803 and Q802.
No
Yes
Is +5V applied to the pin 75 (VDD) of IC802 ? Check the PWB pattern between collector of Q204 and pin 75 of
No IC802.
Yes
Is +5V applied to the pin 1 (VCC) of IC801 ? Check the PWB pattern between collector of Q204 and pin 1 of
No IC801.
Yes
Is +0V applied to the pin 74 (SEL) of IC802 ? Check the laser come on when pattern cut between pin 8 (SEL) of
No IC801 and pin 74 (SEL) of IC802.
Yes
Is approx. 1.8V applied to the collector of Q801. Check the peripheral parts of IC801 and Q801. If it is normal, the
No optical pickup is faulty.
Yes
Check BI801/CNS801. If it is normal, the optical pickup is

faulty.
• Focus failure.
Does the optical pickup move up and down when the disc is Check as stated in item "FOCUS SERVO SAWTOOTH WAVE
removed? No FAILURE".
Yes
Is the following waveform ouput at the pin 62 (FEI) of IC802 Check the periphery of IC801 and BI801/CNS801. Is it normal?
when the disc is set? No
Yes
Yes
pin 62
(FEI) The optical pickup is faulty.
pin 86
(FOO)
pin 63
(SBAD)
Is the waveform shown above input at the pin 63 (SBAD) of Check the pattern between pin 13 of IC801 and pin 63 of IC802.
IC802? No Check the periphery of IC801 and BI801/CNS801.
Yes
IC801 is faulty.
– 21 –

GX-CD1200W
• Focus servo sawtooth wave failure.
Is sawtooh wave output to the pin 66 (FOO) of IC802 ? IC802 is faulty.

No
Yes
1.5~2.5sec
Is +8.1V applied to the pins 1 and 30 (VCC) of IC803 ? Check the PWB pattern of IC803.
No
Yes
Is sawtooth wave obtained between pins 20 and 21 of IC803 ? Check the PWB pattern of IC803.
No
Yes
1.5~2.5sec
Is sawtooth wave obtained between pins 3 and 4 of BI801/ Check the PWB pattern between BI801/CNS801 and IC803.
CNS801 ? (as shown above) No
Yes
BI801/CNS801 connection failure or optical pickup failure.
• Spindle motor clv servo failure.
Is following wave output to the pin 55 (AVSS) of IC802 when Check the procedure in "HF ERROR".
the Function is changed to "PLAY" from "STOP" ? No If OK. IC802 is faulty.
Yes
DMO
Is above wave obtained between pins 5 and 6 of IC803 ? Check the PWB pattern between pin 72 (DMO) of IC802 and pins
No 5 and 6 of IC803. If OK. IC803 is faulty.
Yes
Is above wave obtained between pins 5 and 6 of BI803/ Check the PWB pattern between BI803/CNS803 and IC803.
CNS803 ? No
Yes
BI803/CNS803 connection failure or optical pickup failure.
– 22 –

GX-CD1200W
• Track search failure
Does the sled motor run in FF/REW state when the CD Check as stated in item "SLED MOTOR OPERATION FAILURE".
TEST MODE is set? No
Yes
Is the following wave output to the pin 67 (TRO) of IC802 IC802 failure.
during track search in normal playback? No
Yes
TRO
Is the following wave output to the pins 12 (TEO) of IC801 Check the PWB pattern between pin 67 (TRO) of IC802 and pin
No 28 of IC803.
during track search in normal playback?
Check the PWB pattern between pins 25 and 26 of IC803 and
Yes
Optical pickup.
TEO
TEI If OK. Optical pickup failure.
TEZI
Is the above wave output to the pins 64 (TEI) and 65 (TEZI) Check the PWB pattern between pin 12 (TEO) of IC801 and pins 64
of IC802 during track serch in normal playback? No (TEI) and 65 (TEZI) of IC802. If OK. IC801 failure.
Yes
Is the following wave output to the pin 60 (RFZI) and 61 Check the PWB pattern between pin 22 (RFO) and 18 (RFIS), 17
No (RFRP) of IC801 and pins 60 and 61 of IC802. If OK. IC801 failure.
(RFRP) of IC802 during track search in normal playback?
Yes RFRP
RFZI
Normal.
• Sled motor operation failure.
Is following sled feed signal output the pin 71 (FMO) of IC802 IC802 is faulty.
when FF/REW key is pressed after the CD TEST MODE is No
sated?
Yes FF REW
FMO
Is following sled feed signal input the pins 12 and 13 of IC803 Check the PWB pattern between pin 71 of IC802 and pins 12 and
when FF/REW key is pressed after the CD TEST MODE is No 13 of IC803.
seted?
FF REW
Yes
SL ±
Is sled feed signal output the pins 10 and 11 of IC803? Check the peripheral parts of IC803. If OK, IC803 is faulty.
No
Yes
Is sled feed voltage applied between both terminals of sled Check the BI803/CNS803.
motor? No
Yes
Check the CD mechanism (periphery of sled motor).
If the sled motor does not run when DC2.0V is applied to
both terminals of sled motor, the sled motor is faulty.
• Sled servo failure.

Is following sled signal output the pin 71 (FMO) of IC802 IC802 is faulty.
during playback? No
Yes
FMO
Normal.
– 23 –

GX-CD1200W
FUNCTION TABLE OF IC
IC802 VHiTC9457F0-1: Servo/Signal Control (TC9457F0) (1/4)
Pin No. Port Name Terminal Name Input/Output Function
1* (OT5)S1 SEG1 Output Segment signal output to the LCD panel.
2 (OT6)S2 SEG2 Output Up to 72 segments in a matrix with COM1 to COM4 can be displayed.
3 (OT7)S3 SEG3 Output All of the S1 to S18 pins can be switched for output ports by a program.
4 (OT8)S4 SEG4 Output Also, the S15 to S18 pins each can be switched for I/O ports individually.
5 (OT9)S5 SEG5 Output When set for I/O ports, these pins become Nch open-drain output.
6* (OT10)S6 SEG6 Output Furthermore, the S11 to S14 and the P8-0 to P8-3 pins can be switched for
7* (OT11)S7 SEG7 Output use as CD signal (CLCK to IPF) input/output pins by a program.
8* (OT12)S8 SEG8 Output • CLCK: Subcodes P thru W data readout clock input/output.
9* (OT13)S9 SEG9 Output Selected between input and output by a command.
10* (OT14)S10 SEG10 Output • DATA: Subcodes P thru W data output.
11* (CLCK/OT15) SEG11 Output • SFSY: Playback system frame sync signal output.
S11 • LRCK: Channel clock (44.1kHz) output.
12* (DATA/OT16) SEG12 Output It outputs a low for L channel and a high for R channel.
S12 Polarity can be inverted by a command.
13* (SFSY/OT17) SEG13 Output • BCK : Bit clock (1.4122MHz) output.
S13 • AOUT: Audio data output.
14* (LRCK/OT18) SEG14 Output • MBOV: Buffer memory-over signal output.
S14 It outputs a high when buffer overflows.
15 (BCK/S15) CDSEL0 Output • IPF : Correction flag output. When AOUT is C2 correction output, it
P8-0 outputs a high indicating that correction is impossible.
16 (AOUT/S16) CDSEL1 Output
P8-1
17 (MBOV/S17) CD LID SW Output
P8-2
18 (IPF/S18) DOOR OUT Output
P8-3
19 MVDD MVDD1 — Power supply pins.
20 MVSS MVSS1 — Normally, apply a voltage of 4.5 to 5.5V to VDD.
In a backup state (when the CKSTP instruction executed), the device's
current consumption is reduced to 1µA or less, allowing for the supply
voltage to be lowered to 2.0V.
The device is reset and the program starts from address 0 when a voltage
of 2.7V or more is applied to this pin when it is at 0V (power-on reset).
21* (K0)P1-0 TRAY CLOSE Input 4-bit CMOS I/O ports.
22* (K1)P1-1 TRAY OPEN Input These ports can be set for input or output bit for bit by a program.
23 (K2)P1-2 PUSEL0 Input These pins can be pulled up to VDD or down to GND by program.
24 (K3)P1-3 PUSEL1 Input Therefore, they can be used as key input pins. Also, when they are set for
I/O port, a change of state in this input can be used to clear the clock stop
or wait mode.
25 (DCREF)P3-0 DISPLAY Input 5-bit CMOS I/O ports.
26 (ADin1)P3-1 ADIN1 Input These ports can be set for input or output bit for bit by a program.
27 (ADin2)P3-2 ADIN2 Input The P3-0 to P4-0 pins serve dual purposes as analog inputs for the internal
28 (ADin3)P3-3 MUTE Input 6-bit 4-channel A/D converters.
29 (BUZR/ PU IN Input The internal A/D converters can complete conversion in 6 instruction cycles
ADin4)P4-0 using a successive approximation method. The required pins can be set for
A/D analog input bit for bit by a program. P3-0 can be set for reference
voltage input, and the internal power supply (MVDD) can be used for this
reference voltage.
The P4-0 pin serves dual purposes as a buzzer output pin.
The buzzer output can be selected from 8 frequencies, 0.625 to 3kHz.
Each selected frequency can be output in one of four modes: continuous,
single, 10Hz intermittent, and 10Hz intermittent at 1Hz interval.
Whether or not to use and how to control the A/D converter and buzzer all
can be set by a program.
In this unit, the terminal with asterisk mark (*) is open terminal which is not connected to the outside.
– 24 –

GX-CD1200W
30 (S12)P4-1 PUSEL2 Input 3-bit CMOS I/O ports.
31* (SO/S11/ NC Input/Output These ports can be set for input or output bit for bit by a program.
SDA)P4-2 These pins serve dual purposes as input or output pins for the serial
32* (SCK/SCL) NC Input/Output interface circuit (SIO).
P4-3 The SIO is a 2-wire/3-wire compatible serial interface. 4 or 8 bits of serial
data, beginning with the MSB or LSB, are serially output from the SO/SDA,
pin at each clock edge on the SCK/SCL pin, and the data on S11 or S12
pin is serially input to the device.
The serial clock (SCK/SCL) allows selection between the internal (450/225/
150/75 kHz) and external sources and a selection of the active edge, rise or
fall. Moreover, since the clock and data can be output via Nch open-drain
outputs, various, device controls and communication between controllers
can be greatly facilitated.
When an SIO interrupt is enabled, an interrupt is generated at completion
of SIO execution and the program jumps to address 4.
All inputs to SIO contain a Schmitt trigger circuit.
33 TEST0 TEST0 Input Test mode control input pins.
34 TEST1 TEST1 Input The test mode is selected when these pins are set high and normal
35 TEST2 TEST2 Input operation is selected when they are low.
36 TEST3 TEST3 Input
39* (OT19)/HSO /HSO Output CD control output pins.
40* (OT20)SPCK SPCK Output • /HSO: Playback speed mode output.
41* (OT21)SPDA SPDA Output High = normal speed; Low = double speed.
42* (OT22)COFS COFS Output • SPCK: Processor status signal readout clock output (176.4kHz)
• SPDA: Processor status signal output.
• COFS: Correction system frame clock output (7.35kHz)
These pins can be switched for output ports by a program.
43* DOUT DOUT Input/Output Digital output pin.
44* SBSY SBSY Input/Output Subcode block sync output pin. It outputs a high at the S1 position when
subcode sync is detected.
45* SBOK SBOK Input/Output Subcode Q data CRCC determination result output pin. It outputs a high
when CRCC check is found OK.
46 VDD VDD1 Input/Output CD unit's digital block power supply pins.
47 VSS VSS1 Input/Output Normally, apply 5V to VDD.
When not using a CD (CD off), this power supply can be turned off, with
only the controller power supply kept active, so that the controller alone is
operating. In this case, the CD off bit must be set to 1. When this bit is set
to 1, pins 11 through 18 and pins 39 through 42 all are changed for output
ports if they have been set for CD control signal input/output pins.
48 P2VREF P2VREF Input/Output PLL block-2 VREF pin.
49 PDO PDO Input/Output This pin outputs a phase error between EFM and PLCK signals.
50 TMAX TMAX Input/Output TMAX detection result output pin.
Selected by command bit TMPS.
Longer than preset period: Outputs P2VREF.
Shorter than preset period: Low level (Vss).
Within preset period: High impedance.
51 LPFN LPFN Input/Output Inverted input of low-pass filter amp.
52 LPFO LPFO Input/Output Output of low-pass filter amp.
53 PVREF PVREF Input/Output PLL block VREF pin.
54 VCOF VCOF Input/Output VCO filter pin.
55 AVSS AVSS Input/Output Analog block ground pin.
56 SLCO SLCO Input/Output DAC output pin for data slice level generation.
57 RFI RFI Input/Output RF signal input pin.
58 AVDD AVDD Input/Output Analog block power supply pin.
59 RFCT RFCT Input/Output RFRP signal center level input pin.
60 RFZI RFZI Input/Output RFRP zero-cross input pin.
61 RFRP RFRP Input/Output RF ripple signal input pin.
62 FEI FEI Input/Output Focus error signal input pin.
– 25 –

GX-CD1200W
63 SBAD SBAD Input/Output Subbeam add signal input pin.
64 TEI TEI Input/Output Tracking error input pin.
This input is read when tracking servo is on.
65 TEZI TEZI Input/Output Tracking error zero-cross input pin.
66 FOO FOO Input/Output Focus equalizer output pin.
67 TRO TRO Input/Output Tracking equalizer output pin.
68 VREF VREF Input/Output Analog reference power supply pin.
69 RFGC RFGC Input/Output RF amplitude adjusting control signal output pin. It outputs 3-level PWM
signals. (PWM carrier = 88.2kHz)
70 TEBC TEBC Input/Output Tracking balance control signal output pin. It outputs 3-level PWM signals.
(PWM carrier = 88.2kHz)
71 FMO FMO Input/Output Focus equalizer output pin. It outputs 3-level PWM signals.
(PWM carrier = 88.2kHz)
72 DMO DMO Input/Output Disc equalizer output pin. It outputs 3-level PWM signals.
(PWM carrier = DSP block 88.2kHz, synchronized to PXO)
73 2VREF 2VREF Input/Output Analog reference power supply pin. (2 x VREF)
74 SEL SEL Input/Output APC circuit on/off signal output pin.
When laser is on, this pin goes to a high-impedance state when UHS = low
and outputs a high when UHS = high
75 VDD VDD2 Input/Output CD unit's digital block power supply pins.
76 VDD VSS2 Input/Output Normally, apply 5V to VDD.
When not using a CD (CD off), this power supply can be turned off, with
only the controller power supply kept active, so that the controller alone is
operating. In this case, the CD off bit must be set to 1. When this bit is set
to 1, pins 11 through 18 and pins 39 through 42 all are changed for output
ports if they have been set for CD control signal input/output pins.
77 XVSS XVSS Input/Output CD's crystal oscillator power supply pins.
Normally, connect these pins to the power supply lines that are used in
common for the VDD and VSS pins.
78 XI XI Input/Output CD's crystal oscillator input/output pins.
79 XO XO Input/Output Normally, connect 16.934MHz here. This clock is used as the system clock
for the CD. After a system reset, it also is used as the system clock on the
controller side.
80 XVDD XVDD Input/Output CD's crystal oscillator input/output pins.
Normally, connect these pins to the power supply lines that are used in
common for the VDD and VSS pins.
81 DVSR DVSR Input/Output R-channel D/A converter unit ground pin.
82 RO RO Input/Output R-channel data forward output pin.
83 DVRR DVRR Input/Output R-channel reference voltage pin.
84 DVDD DVDD Input/Output D/A converter unit power supply pin.
85 DVRL DVRL Input/Output L-channel reference voltage pin.
86 LO LO Input/Output L-channel data forward output pin.
87 DVSL DVSL Input/Output L-channel D/A converter unit ground pin.
88 NC NC Input/Output NC pins. Normally, connect these pins to ground or leave them open.
89* NC/VPP NC Input/Output
90 /RST RESET Input Device's system reset signal input pin.
The device remains reset while RESET is held low and when RESET is
released back high, the CD unit becomes operational and the program
starts from address 0. Normally, a system reset is asserted when a voltage
of 2.7V or more is applied to VDD when it is at 0V (power-on reset).
Therefore, this pin must be pulled high when used for this purpose.
– 26 –

GX-CD1200W
91 /HOLD HOLD Input This pin is used to input a signal that requests or clears the hold mode.
Normally, use this pin for CD mode select signal input or battery detection
signal input.
There are two hold modes: clock stop mode (crystal oscillator turned off)
and a wait mode (CPU stopped). These modes are entered by executing
the CKSTP and WAIT instructions, respectively.
The clock stop mode can be requested by a programmed input: low level
detection on HOLD pin or forced execution, and can be cleared by
detecting a high on the HOLD pin or a change of state in its input signal.
When the CKSTP instruction is executed, the clock generator and the CPU
stop operating and the device is placed in a memory backup state. During
this state, the device's current consumption is reduced to 1µA or less.
At the same time, the display output and CMOS output ports are
automatically set low, and the Nch open-drain outputs are turned off.
The wait mode is executed regardles of the input state on the HOLD pin,
with the device's current consumption reduced.
This mode is cleared by a change of state in the HOLD input.
92 INTR REMO-IN Input External interrupt input pin.
When the interrupt facility is enabled and a pulse of 1.11 to 2.22µs in
duration is applied to this pin, an interrupt is generated and the program
jumps to address 1. Input logic and the active edge (rise or fall) can be
selected for each interrupt input.
Also, the internal 8-bit time clock can be chosen for this interrupt input, in
which case it is possible to count pulses or generate an interrupt at a given
pulse count (address 3).
93* MXO MXO — Crystal oscillator pins for the controller.
94* MXI MXI — The oscillator clock is used as the timebase for the clock facility or as the
controller's system clock. Connect a 4.5MHz or 75kHz crystal resonator to
the MXO and MXI pins. Since these pins do not contain internal feedback
resistors, etc, an amp resistor or output resistor must be added external to
the chip.
When using the clock generated by the CD unit's crystal oscillator for
clocking the entire device operation, fix the MXI pin to the GND level.
Oscillation is stopped by executing a CKSTP instruction.
Select the crystal oscillator and control its operation by a program.
95 MVSS MVSS — Power supply pins.
96 MVDD MVDD — Normally, apply a voltage of 4.5 to 5.5V to VDD.
In a backup state (when the CKSTP instruction executed), the device's
current consumption is reduced to 1µA or less, allowing for the supply
voltage to be lowered to 2.0V.
The device is reset and the program starts from address 0 when a voltage
of 2.7V or more is applied to this pin when it is at 0V (power-on reset).
97 OT1 COM1 Output Common signal outputs to the LCD panel.
98 OT2 COM2 Output Up to 72 segments in a matrix with S1 to S18 can be displayed.
99 OT3 COM3 Output Three voltage levels MVDD, VEE (1/2 MVDD), and GND are output for
100 OT4 COM4 Output 83Hz period at 2ms intervals.
After a system reset and after deassertion of a clock stop instruction, the
VEE voltage is output and the DISP OFF bit is set to 0 before common
signals are output.
To serial No.006XXXXX From serial No.007XXXXX
TC9457F-013 TC7457F-022
JAPAN JAPAN
– 27 –

GX-CD1200W
—MEMO—
– 28 –

GX-CD1200W
PARTS GUIDE
PORTABLE CD STEREO
COMPONENT SYSTEM
GX-CD1200W(BK)
MODEL GX-CD1200W(GL)
“HOW TO ORDER REPLACEMENT PARTS”

To have your order filled promptly and correctly, please furnish the
For U.S.A. only
following information. Contact your nearest SHARP Parts Distributor to order.
1. MODEL NUMBER 2. REF. No.
3. PART NO. 4. DESCRIPTION For location of SHARP Parts Distributor,
Please call Toll-Free;
1-800-BE-SHARP
MARK: SPARE PARTS-DELIVERY SECTION
Explanation of capacitors/resistors parts codes

Capacitors Resistors
VCC ....................... Ceramic type VRD ....................... Carbon-film type
VCK ........................ Ceramic type VRS ........................ Carbon-film type
VCT ........................ Semiconductor type VRN ....................... Metal-film type
VC • • MF ............... Cylindrical type (without lead wire) VR • • MF ............... Cylindrical type (without lead wire)
VC • • MN ............... Cylindrical type (without lead wire) VR • • MN ............... Cylindrical type (without lead wire)
VC • • TV ................ Square type (without lead wire) VR • • TV ................ Square type (without lead wire)
VC • • TQ ............... Square type (without lead wire) VR • • TQ ............... Square type (without lead wire)
VC • • CY ............... Square type (without lead wire) VR • • CY ............... Square type (without lead wire)
VC • • CZ ............... Square type (without lead wire) VR • • CZ ............... Square type (without lead wire)
VC • • • • • • • • • J .. The 13th character represents capacity difference. VR • • • • • • • • • J .. The 13th character represents error.
("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%, ("J" ±5%, "F" ±1%, "D" ±0.5%.)
"C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.)
If there are no indications for other parts, the resistors are ±5%
If there are no indications for the electrolytic capacitors, error is ±20%. carbon-film type.
NOTE:
Parts marked with “ ” are important for maintaining the safety of the set.
Be sure to replace parts with specified ones for maintaining the safety and performance of the set.
– 29 –

GX-CD1200W
PRICE PRICE
NO. PARTS CODE DESCRIPTION NO. PARTS CODE DESCRIPTION
RANK RANK
INTEGRATED CIRCUITS VR202 RVR-Q0002BGZZ J AE 50 kohms (B)×2 [X-BASS]

VR203~205 RVR-Q0001BGZZ J AC 100 kohm (B)×2
IC1 VHITA7358AP-1 J AG FM Front End,TA7358AP [Graphic Equalizer]
IC2 VHILA1805//-1 J AM FM/AM IF MPX.,LA1805 VR401 RVR-B0002BGZZ J 50 kohms (B)×2 [VOLUME]
IC101 VHITA8189N/-1 J AM Record/Playback Amp.,TA8189N
IC151 VHITA2011S/-1 J AM Mic Amp.,TA2011S VARIABLE CAPACITORS
IC201 VHIBA3822LS-1 J AL Graphic Equalizer,BA3822LS
IC202,203 VHILB1403N/-1 J AG Level Meter Driver,LB1403N TC5,6 RTO-H1003SJZZ J AG Trimmer,5 pF
IC401 VHIKIA4558P-1 J AC Ope Amp.,KIA4558P TC7,8 RTO-H1001BGZZ J AD Trimmer,10 pF
IC402 VHILA4663//-1 J AQ Power Amp.,LA4663 TC9 RVC-Z0001BGZZ J AF Fine Tuning
IC501,502 VHIKA7809AP-1 J Voltage Regulator,KA7809AP VC1~4 RVC-R0001BGZZ J AK Variable Capacitance with
IC801 VHITA2109F/-1 J AL Servo Pre Amp.,TA2109F Trimmer (TC1~4)
IC802 VHITC9457F0-1 J AZ Servo/Signal Control,TC9457F0
IC803 VHILA6541D/-1 J AW Focus/Tracking/Spin/Sled Driver, VIBRATOR
LA6541D
XL801 RCRM-0008AWZZ J AF Ceramic,16.93 MHz
TRANSISTORS
CAPACITORS
Q153 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q154 VSKRA102M//-1 J AC Digital,PNP,KRA102 M C2 VCCCPU1HH5R0J J AA 5 pF (CH),50V
Q156 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR C4 VCCCPU1HH240J J AA 24 pF (CH),50V
Q181,182 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR C5 VCKYPA1HB102K J AA 0.001 µF,50V
Q301 VSKTC3203Y/-1 J AC Silicon,NPN,KTC3203 Y C6,7 VCKYPA1HB472K J AB 0.0047 µF,50V
Q403,404 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR C8,9 VCKZPA1HF223Z J AA 0.022 µF,50V
Q502,503 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR C10 VCCCPU1HH150J J AA 15 pF (CH),50V
Q504 VSKTA1271Y/-1 J AC Silicon,PNP,KTA1271 Y C11 VCCCPU1HH220J J AA 22 pF (CH),50V
Q505 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR C12 VCCCPU1HH3R0J J AA 3 pF (CH),50V
Q601 VSKRC102M//-1 J AC Digital,NPN,KRC102 M C13 VCKZPA1HF223Z J AA 0.022 µF,50V
Q602 VSKRA102M//-1 J AC Digital,PNP,KRA102 M C14 VCCCPU1HH5R0J J AA 5 pF (CH),50V
Q603 VSKTD2058Y/-1 J AF Silicon,NPN,KTD2058 Y C15 VCKZPA1HF223Z J AA 0.022 µF,50V
Q801 VSKTA1266GR-1 J AB Silicon,PNP,KTA1266 GR C17 VCKZPA1HF223Z J AA 0.022 µF,50V
Q802 VSKTA1271Y/-1 J AC Silicon,PNP,KTA1271 Y C18 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
Q803,804 VSKRC102M//-1 J AC Digital,NPN,KRC102 M C19 VCKYPA1HB331K J AA 330 pF,50V
C20 VCKYPA1HB222K J AA 0.0022 µF,50V
DIODES C21 VCCUPA1HJ5R0C J AA 5 pF (UJ),50V
C22 VCKZPA1HF223Z J AA 0.022 µF,50V
D1,2 VHDDS1SS133-1 J AB Silicon,DS1SS133 C23 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic
D152 VHDDS1SS133-1 J AB Silicon,DS1SS133 C24~26 VCKZPA1HF223Z J AA 0.022 µF,50V
D154 VHDDS1SS133-1 J AB Silicon,DS1SS133 C27 VCKYPA1HB472K J AB 0.0047 µF,50V
D156 VHDDS1SS133-1 J AB Silicon,DS1SS133 C29 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic
D158 VHDDS1SS133-1 J AB Silicon,DS1SS133 C30 VCKZPA1HF223Z J AA 0.022 µF,50V
D162~165 VHDDS1SS133-1 J AB Silicon,DS1SS133 C31 VCQYKA1HM472K J AB 0.0047 µF,50V,Mylar
! D651 VHDTS4B03GM-1 J AK Silicon,TS4B03GM C32 VCQYKA1HM822K J AA 0.0082 µF,50V,Mylar
DZ601 VHEDZ8R2BSB-1 J AB Zener,8.2V,DZ8.2BSB C33 RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic
LED1 VHP333ID213-1 J LED,RED,333ID213 C34 VCKYPA1HB471K J AA 470 pF,50V
LED253~260 VHP333ID213-1 J LED,RED,333ID213 C35 RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic
LED401 VHP333ID213-1 J LED,RED,333ID213 C36 92LCPU100V1500 J AC 0.0015 µF,100V
LED501,502 VHP333ID213-1 J LED,RED,333ID213 C37,38 VCQYKA1HM123K J AA 0.012 µF,50V,Mylar
C39~41 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
FILTERS C42 VCKZPA1HF223Z J AA 0.022 µF,50V
C43 VCKYPA1HB221K J AA 220 pF,50V
CF1 RFILR0008AWZZ J AE FM Band Pass Filter C101,102 VCKYPA1HB471K J AA 470 pF,50V
CF2 92LFILTF1342A J AD FM IF,10.7 MHz C103,104 VCKYPA1HB471K J AA 470 pF,50V
CF3 RFILA0001BGZZ J AC AM IF,455 kHz C105~108 VCKYPA1HB331K J AA 330 pF,50V
C109,110 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
TRANSFORMER C111,112 VCQYKA1HM153K J AB 0.015 µF,50V,Mylar
C113~116 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic
! T601 RTRNP0001BGZZ J AX Power C117,118 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C119,120 VCQYKA1HM333K J AB 0.033 µF,50V,Mylar
COILS C121,122 VCKYPA1HB331K J AA 330 pF,50V
C123,124 VCKYPA1HB103K J AA 0.01 µF,50V
L1 RCILB0001BGZZ J AD FM Oscillation C125,126 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic
L2 RCILR0001BGZZ J AA FM Tracking C127 RC-GZA337AF1A J AB 330 µF,10V,Electrolytic
L3,4 RCILA0001BGZZ J AH MW/SW1 Bar Antenna C128 RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
L5 RCILA0003BGZZ J AC SW2 Antenna C129 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic
L6 RCILB0002BGZZ J AC MW Oscillation C131,132 VCKYPA1HB121K J AA 120 pF,50V
L7 RCILB0003BGZZ J AC SW1 Oscillation C133,134 VCKYPA1HB151K J AA 150 pF,50V
L8 RCILB0004BGZZ J AC SW2 Oscillation C137,138 VCQYKA1HM152K J AB 0.0015 µF,50V,Mylar
L9 RCILI0002BGZZ J AD FM IF C151 RC-GZA334AF1H J AA 0.33 µF,50V,Electrolytic
L10 RCILI0003BGZZ J AD FM Detection C152 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
L11 RCILI0001BGZZ J AD AM IF C154 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
L103,104 VP-MK223K0000 J AC 22 mH,Choke C155 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
L301 RCILB0005BGZZ J AD Bias Oscillation C156 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
L501 VP-MK470K0000 J AB 47 µH,Choke C157 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
L801 VP-DHR82K0000 J AE 0.82 µH,Choke C158,159 RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
L802,803 VP-DH100K0000 J AB 10 µH,Choke C160 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic
C180 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
VARIABLE RESISTORS C181,182 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C183,184 VCKYPA1HB221K J AA 220 pF,50V
VR1 RVR-M0026AWZZ J AC 10 kohm (B),Semi-VR [VCO] C185,186 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
VR102 RVR-M0018AWZZ J AC 470 ohms (B),Semi-VR C200 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
[Tape Speed] C201,202 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic
–1–

GX-CD1200W
PRICE PRICE
NO. PARTS CODE RANK
DESCRIPTION NO. PARTS CODE DESCRIPTION
RANK
C203,204 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic C846 RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic

C205,206 VCQYKA1HM103K J AA 0.01 µF,50V,Mylar C847 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic
C207,208 VCKYPA1HB471K J AA 470 pF,50V C848 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic
C209,210 VCQYKA1HM823K J AC 0.082 µF,50V,Mylar C849,850 VCKYPA1HB121K J AA 120 pF,50V
C211,212 VCQYKA1HM152K J AB 0.0015 µF,50V,Mylar C851,852 RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic
C213,214 RC-GZA334AF1H J AA 0.33 µF,50V,Electrolytic C853 VCKZPA1HF223Z J AA 0.022 µF,50V
C215,216 VCQYKA1HM562K J AA 0.0056 µF,50V,Mylar C854 VCKYPA1HB682K J AB 0.0068 µF,50V
C217,218 RC-GZA474AF1H J AA 0.47 µF,50V,Electrolytic C855 VCKZPA1HF223Z J AA 0.022 µF,50V
C219,220 VCQYKA1HM393K J AB 0.039 µF,50V,Mylar C858 VCKZPA1HF223J J 0.022 µF,50V
C221,222 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic C859 VCKYPA1HB272K J AA 0.0027 µF,50V
C251,252 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic C860 VCKYPA1HB152K J AA 0.0015 µF,50V
C253,254 VCKZPA1HF223Z J AA 0.022 µF,50V C863 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
C255,256 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic C893 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic
C257 RC-GZA476AF1E J AB 47 µF,25V,Electrolytic C894 VCKZPA1HF223Z J AA 0.022 µF,50V
C259,260 VCQYKA1HM392K J AA 0.0039 µF,50V,Mylar
C301 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic RESISTORS
C302 VCQYKA1HM222K J AA 0.0022 µF,50V,Mylar
C303 VCQYKA1HM562K J AA 0.0056 µF,50V,Mylar R1 VRD-ST2EE100J J AA 10 ohm,1/4W
C304 VCKZPA1HF223Z J AA 0.022 µF,50V R2 VRD-ST2CD330J J AA 33 ohms,1/6W
C305 VCQYKA1HM152K J AB 0.0015 µF,50V,Mylar R3 VRD-ST2CD470J J AA 47 ohms,1/6W
C306 VCKYPA1HB391K J AA 390 pF,50V R4 VRD-ST2CD334J J AA 330 kohms,1/6W
C307 VCKYPA1HB151K J AA 150 pF,50V R5 VRD-ST2CD101J J AA 100 ohm,1/6W
C401,402 VCQYKA1HM682K J AA 0.0068 µF,50V,Mylar R7 VRD-ST2CD824J J AA 820 kohms,1/6W
C403,404 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic R8 VRD-ST2CD392J J AA 3.9 kohms,1/6W
C405,406 VCQYKA1HM332K J AA 0.0033 µF,50V,Mylar R9 VRD-ST2CD123J J AA 12 kohms,1/6W
C407,408 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic R10,11 VRD-ST2EE470J J AA 47 ohms,1/4W
C409,410 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic R12 VRD-ST2CD102J J AA 1 kohm,1/6W
C411 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic R13 VRD-ST2EE101J J AA 100 ohm,1/4W
C412 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic R14 VRD-ST2CD104J J AA 100 kohm,1/6W
C413,414 VCQYKA1HM102K J AA 0.001 µF,50V,Mylar R15,16 VRD-ST2CD103J J AA 10 kohm,1/6W
C415,416 VCQYKA1HM154K J AB 0.15 µF,50V,Mylar R17,18 VRD-ST2CD272J J AA 2.7 kohms,1/6W
C418 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic R19 VRD-ST2CD153J J AA 15 kohms,1/6W
C419,420 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic R20 VRD-ST2EE100J J AA 10 ohm,1/4W
C423 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic R100 VRD-ST2EE151J J AA 150 ohms,1/4W
C424 RC-GZA476AF1E J AB 47 µF,25V,Electrolytic R101,102 VRD-ST2CD101J J AA 100 ohm,1/6W
C425~428 VCQYKA1HM104K J AB 0.1 µF,50V,Mylar R105,106 VRD-ST2CD184J J AA 180 kohms,1/6W
C429,430 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic R107,108 VRD-ST2CD103J J AA 10 kohm,1/6W
C433 VCKZPA1HF223Z J AA 0.022 µF,50V R109,110 VRD-ST2CD682J J AA 6.8 kohms,1/6W
C505 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic R111,112 VRD-ST2CD223J J AA 22 kohms,1/6W
C506 VCKZPA1HF223Z J AA 0.022 µF,50V R113,114 VRD-ST2CD124J J AA 120 kohms,1/6W
C508 RC-GZA107AF1C J AB 100 µF,16V,Electrolytic R115,116 VRD-ST2CD681J J AA 680 ohms,1/6W
C510 RC-GZG338AF1E J 3300 µF,25V,Electrolytic R119,120 VRD-ST2CD101J J AA 100 ohm,1/6W
C511 VCKZPA1HF223Z J AA 0.022 µF,50V R121~124 VRD-ST2CD103J J AA 10 kohm,1/6W
C513,514 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic R127,128 VRD-ST2CD223J J AA 22 kohms,1/6W
C602 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic R131,132 VRD-ST2CD122J J AA 1.2 kohms,1/6W
C604 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic R135,136 VRD-ST2CD103J J AA 10 kohm,1/6W
C651~654 VCKZPA1HF223Z J AA 0.022 µF,50V R151 VRD-ST2CD222J J AA 2.2 kohms,1/6W
C801 VCQYKA1HM103K J AA 0.01 µF,50V,Mylar R152 VRD-ST2CD472J J AA 4.7 kohms,1/6W
[To Serial No.00404990 Only] R153 VRD-ST2CD222J J AA 2.2 kohms,1/6W
C802 VCKZPA1HF223Z J AA 0.022 µF,50V R154 VRD-ST2CD561J J AA 560 ohms,1/6W
C804 VCCCPA1HH2R0C J AA 2 pF (CH),50V R161 VRD-ST2CD105J J AA 1 Mohm,1/6W
C805 VCKZPA1HF223Z J AA 0.022 µF,50V R165 VRD-ST2CD103J J AA 10 kohm,1/6W
C806 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic R166 VRD-ST2EE561J J AA 560 ohms,1/4W
C807 VCKZPA1HF473Z J AA 0.047 µF,50V R168,169 VRD-ST2CD103J J AA 10 kohm,1/6W
C813 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic R170,171 VRD-ST2CD333J J AA 33 kohms,1/6W
C814 VCKZPA1HF473Z J AA 0.047 µF,50V R172,173 VRD-ST2CD103J J AA 10 kohm,1/6W
C815 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic R174 VRD-ST2CD223J J AA 22 kohms,1/6W
C816 VCKZPA1HF223Z J AA 0.022 µF,50V R177 VRD-ST2CD102J J AA 1 kohm,1/6W
C818 VCCSPA1HL560J J AA 56 pF,50V R181,182 VRD-ST2CD102J J AA 1 kohm,1/6W
C819,820 VCQYKA1HM104K J AB 0.1 µF,50V,Mylar R183,184 VRD-ST2CD334J J AA 330 kohms,1/6W
C821 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic R185,186 VRD-ST2CD221J J AA 220 ohms,1/6W
C822 VCKZPA1HF473Z J AA 0.047 µF,50V R187,188 VRD-ST2CD392J J AA 3.9 kohms,1/6W
C823 VCKZPA1HF223Z J AA 0.022 µF,50V R200 VRD-ST2EE331J J AA 330 ohms,1/4W
C824 VCQYKA1HM104K J AB 0.1 µF,50V,Mylar R201,202 VRD-ST2CD102J J AA 1 kohm,1/6W
C826 VCCSPA1HL470J J AA 47 pF,50V R205 VRD-ST2CD472J J AA 4.7 kohms,1/6W
C827 VCQYKA1HM153K J AB 0.015 µF,50V,Mylar R206 VRD-ST2CD332J J AA 3.3 kohms,1/6W
C828 VCKYPA1HB272K J AA 0.0027 µF,50V R207 VRD-ST2CD472J J AA 4.7 kohms,1/6W
C829 VCKYPA1HB472K J AB 0.0047 µF,50V R208 VRD-ST2CD332J J AA 3.3 kohms,1/6W
C830 VCQYKA1HM103K J AA 0.01 µF,50V,Mylar R211,212 VRD-ST2CD102J J AA 1 kohm,1/6W
C833 VCQYKA1HM333K J AB 0.033 µF,50V,Mylar R253,254 VRD-ST2CD393J J AA 39 kohms,1/6W
C834,835 VCKYPA1HB471K J AA 470 pF,50V R255,256 VRD-ST2EE121J J AA 120 ohms,1/4W
C836~839 VCQYKA1HM473K J AB 0.047 µF,50V,Mylar R257,258 VRD-ST2CD103J J AA 10 kohm,1/6W
C840~842 VCKZPA1HF473K J AA 0.047 µF,50V R259,260 VRD-ST2EE121J J AA 120 ohms,1/4W
C844 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic R302,303 VRD-ST2EE101J J AA 100 ohm,1/4W
C845 VCKZPA1HF473Z J AA 0.047 µF,50V R304 VRD-ST2EE100J J AA 10 ohm,1/4W
–2–

GX-CD1200W
PRICE PRICE
RANK RANK
R305 VRD-ST2EE273J J AA 27 kohms,1/4W CNP501 QTANA0001BGZZ J AD Terminal,Speaker

R306 VRD-ST2EE470J J AA 47 ohms,1/4W CNP601 QCNCM035BAWZZ J AB Plug,2Pin
R351,352 VRD-ST2CD473J J AA 47 kohms,1/6W CNP803 92LCONE6P53254 J AC Plug,6Pin
R353,354 VRD-ST2CD273J J AA 27 kohms,1/6W CNP804 QCNCM705FAFZZ J AB Plug,6Pin
R401,402 VRD-ST2CD104J J AA 100 kohm,1/6W CNS101 QCNWN0001BGZZ J AD Connector Ass’y,3Pin
R403,404 VRD-ST2CD103J J AA 10 kohm,1/6W CNS102 QCNWN0002BGZZ J AE Connector Ass’y,4Pin
R405,406 VRD-ST2CD272J J AA 2.7 kohms,1/6W CNS103 QCNWN0003BGZZ J AF Connector Ass’y,9Pin
R407~410 VRD-ST2CD123J J AA 12 kohms,1/6W CNS601 QCNWN0006BGZZ J AD Connector Ass’y,2Pin
R411 VRD-ST2EE331J J AA 330 ohms,1/4W ! F601 QFS-D402ABGNI J AC T4A L 250V
R412,413 VRD-ST2CD103J J AA 10 kohm,1/6W FW1 QCNWN0038BGZZ J Flat Wire,4Pin
R415,416 VRD-ST2CD332J J AA 3.3 kohms,1/6W FW2 QCNWN0014BGZZ J AA Flat Wire,2Pin
R417,418 VRD-ST2CD223J J AA 22 kohms,1/6W FW801 QCNWN0030AFZZ J AG Flat Wire,10Pin
R419,420 VRD-ST2CD332J J AA 3.3 kohms,1/6W FW802 QCNWN0029AFZZ J Flat Wire,2Pin
R425,426 VRD-ST2CD102J J AA 1 kohm,1/6W J151 QJAKA0004BGZZ J Jack,Mic
R427,428 VRD-ST2CD472J J AA 4.7 kohms,1/6W J401 QJAKM0001BGZZ J AE Jack,Headphones
R429 VRD-ST2CD104J J AA 100 kohm,1/6W LCD801 RV-LX0001BGZZ J LCD Display
R431 VRD-ST2CD273J J AA 27 kohms,1/6W M501(300-10) 92L1959123012 J Motor with Pulley [Tape]
R433~436 VRD-ST2CD2R2J J AA 2.2 ohms,1/6W M801 92LMMTR1651B J AL Motor with Chassis [Sled]
R437,438 VRD-ST2EE121J J AA 120 ohms,1/4W M802 92LMMTR1854A J AP Motor with Gear [Spindle]
R440 VRD-ST2EE471J J AA 470 ohms,1/4W MIC151 RMICC0001BGZZ J AF Built-in Microphone
R441,442 VRD-ST2CD153J J AA 15 kohms,1/6W ! SO601 QSOCA0006SJZZ J AB AC Socket
R511~513 VRD-ST2CD103J J AA 10 kohm,1/6W SP401,402 VSP0012PBG28A J Speaker,Woofer
R514 VRD-ST2CD104J J AA 100 kohm,1/6W SP403,404 RALMB0001BGZZ J AC Speaker,Tweeter
R515 VRD-ST2CD121J J AA 120 ohms,1/6W SW1 QSW-S9001BGZZ J AE Switch,Slide Type
R516 VRD-ST2CD302J J AA 3.6 kohms,1/6W [Band Selector]
R518,519 VRD-ST2CD102J J AA 1 kohm,1/6W SW101 QSW-S9002BGZZ J AD Switch,Slide Type
R520,521 VRD-ST2CD103J J AA 10 kohm,1/6W [Record/Playback]
R601 VRD-ST2EE271J J AA 270 ohms,1/4W SW102 QSW-S9003BGZZ J AC Switch,Slide Type [Beat Cancel]
R602 VRD-ST2EE101J J AA 100 ohm,1/4W SW103 QSW-S9004BGZZ J AC Switch,Slide Type [Dubbing
R801 VRD-ST2EE220J J AA 22 ohms,1/4W Speed/Mic/FM Mode]
R802 VRD-ST2CD222J J AA 2.2 kohms,1/6W SW401 QSW-P9001BGZZ J AE Switch,Push Type [Surround]
[To Serial No.00404990 Only] SW501 QSW-S9005BGZZ J AD Switch,Slide Type
R803 VRD-ST2CD823J J AA 82 kohms,1/6W [Function Selector]
R804 VRD-ST2CD683J J AA 68 kohms,1/6W ! SW601 QSW-S0004SJZZ J AK Switch,Slide Type
R805 VRD-ST2CD393J J AA 39 kohms,1/6W [Voltage Selector]
R806 VRD-ST2CD272J J AA 2.7 kohms,1/6W SW702 QSWF9001AW01 J Switch,Push Type [Pickup In]
R807 VRD-ST2CD102J J AA 1 kohm,1/6W SW801 QSW-K0008AWZZ J AC Switch,Key Type [Play/Pause]
R811 VRD-ST2CD223J J AA 22 kohms,1/6W SW801 92LSWICHT1663 J AC Switch,Key Type [Play/Pause]
R812 VRD-ST2CD102J J AA 1 kohm,1/6W SW802 QSW-K0008AWZZ J AC Switch,Key Type [Stop]
R820 VRD-ST2CD473J J AA 47 kohms,1/6W SW803 QSW-K0008AWZZ J AC Switch,Key Type [Cue/Track Up]
R821,822 VRD-ST2CD223J J AA 22 kohms,1/6W SW804 QSW-K0008AWZZ J AC Switch,Key Type
R824 VRD-ST2CD103J J AA 10 kohm,1/6W [Review/Track Down]
R826 VRD-ST2CD224J J AA 220 kohms,1/6W SW810 QSW-P0004AWZZ J AE Switch,Push Type [Open/Close]
R827 VRD-ST2CD153J J AA 15 kohms,1/6W SW901(300-12) 92L640101149 J Switch,Leaf Type [Tape 1 Main]
R828 VRD-ST2CD103J J AA 10 kohm,1/6W SW902(300-11) 92L640101149 J Switch,Leaf Type [Tape 2 Main]
R829 VRD-ST2CD332J J AA 3.3 kohms,1/6W SW903(300-13) 92L640101149 J Switch,Leaf Type [Tape 2 Play]
R830 VRD-ST2CD103J J AA 10 kohm,1/6W SW904(300-14) 92L64030204 J Switch,Slide Type
R831~834 VRD-ST2CD332J J AA 3.3 kohms,1/6W [Tape 2 Direction]
R835,836 VRD-ST2CD153J J AA 15 kohms,1/6W
R839 VRD-ST2CD473J J AA 47 kohms,1/6W CD MECHANISM PARTS
R840 VRD-ST2EE100J J AA 10 ohm,1/4W
R844 VRD-ST2CD332J J AA 3.3 kohms,1/6W 301 NGERH0011AWZZ J AC Gear,Middle
R846 VRD-ST2CD331J J AA 330 ohms,1/6W 302 NGERH0012AWZZ J AC Gear,Drive
R847 VRD-ST2CD102J J AA 1 kohm,1/6W 303 MLEVP0080AWZZ J AC Rail,Guide
R848 VRD-ST2CD222J J AA 2.2 kohms,1/6W 304 NSFTM0020AWFW J AD Shaft,Guide
R849 VRD-ST2CD682J J AA 6.8 kohms,1/6W 305 92LMCUSN1524A J AD Cushion
R851~853 VRD-ST2CD222J J AA 2.2 kohms,1/6W ! 306 92LHPC1LASY J Pickup Unit Ass’y
R857,858 VRD-ST2CD562J J AA 5.6 kohms,1/6W [To Serial No.00404990]
R861 VRD-ST2CD332J J AA 3.3 kohms,1/6W ! 306 92LHPC1LXASY J BD Pickup Unit Ass’y
R863 VRD-ST2CD332J J AA 3.3 kohms,1/6W [From Serial No.00504991]
R865 VRD-ST2CD102J J AA 1 kohm,1/6W 307 PCOVP1001AWSA J AE Cover,CD Mechanism
R891 VRD-ST2CD683J J AA 68 kohms,1/6W 701 XBSSD26P06000 J AA Screw,ø2.6×6mm
[From Serial No.00504991] 702 XHBSD20P05000 J AA Screw,ø2×5mm
R892 VRD-ST2CD563J J AA 56 kohms,1/6W 703 XBBSD20P03000 J AA Screw,ø2×3mm
[From Serial No.00504991] 704 LX-WZ1070AFZZ J AA Washer,ø1.5×ø3.8×0.25mm
R893~895 VRD-ST2CD683J J AA 68 kohms,1/6W M801 92LMMTR1651B J AL Motor with Chassis [Sled]
[From Serial No.00504991] M802 92LMMTR1854A J AP Motor with Gear [Spindle]
R896 VRD-ST2CD563J J AA 56 kohms,1/6W SW702 QSWF9001AW01 J Switch,Push Type [Pickup In]
[From Serial No.00504991]
CABINET PARTS
OTHER CIRCUITRY PARTS
201 GCABA1003BGSA J Front Cabinet [GL]
BI801/CNS801 QCNWN0026BGZZ J Connector Ass’y,8/8Pin 201 GCABA1003BGSB J Front Cabinet [BK]
BI802/CNS802 QCNWN0027BGZZ J Connector Ass’y,5/5Pin 202 GFTAC0001BGSB J AK Cassette Holder [Tape 1] [BK]
[To Serial No.00404990] 202 GFTAC0001BGSC J Cassette Holder [Tape 1] [GL]
BI802/CNS802 QCNWN0032BGZZ J Connector Ass’y,7/7Pin 203 GFTAC0002BGSB J AK Cassette Holder [Tape 2] [BK]
[From Serial No.00504991] 203 GFTAC0002BGSC J Cassette Holder [Tape 2] [GL]
BI803/CNS803 QCNWN0028BGZZ J Connector Ass’y,6/6Pin 204 HBDGA1003BGSA J Badge,SHARP
BI804/CNS804 QCNWN0031BGZZ J Connector Ass’y,6/6Pin 205 HBDGS1001BGSA J AF Sheet,Surround Sound System
CNP101 QCNCM705CAFZZ J AA Plug,3Pin 206 HDECQ0001BGSA J AH Panel,Display
CNP102 QCNCM705DAFZZ J AB Plug,4Pin 207 HDECQ0004BGSA J AD Ring,Volume Knob
CNP103 QCNCM698JAFZZ J AC Plug,9Pin 208 HDECQ0017BGSA J Panel,Cassette Holder [Tape 1]
–3–

GX-CD1200W
PRICE PRICE
NO. PARTS CODE RANK
DESCRIPTION NO. PARTS CODE DESCRIPTION
RANK
209 HDECQ0008BGSA J AD Panel,Cassette Holder [Tape 2] 264 TSPC-0026BGZZ J Label,Specifications [BK]

210 HDECZ0001BGSA J AC Panel,Dial Pointer [For Malaysia/Asia Middle East/
211 HSSND0001BGSA J AC Dial Pointer Africa]
212 JKNBQ0001BGSC J Knob,Tuning 264 TSPC-0027BGZZ J Label,Specifications [BK]
213 LANGT0001BGFW J AD Bracket,Front Cabinet [For Jordan/Egypt]
214 MLIFP0001BGZZ J AD Gear,Cassette Holder 264 TSPC-0028BGZZ J Label,Specifications [BK]
215 MSPRD0001BGFW J AB Spring,Cassette Holder Up [For Thailand]
216 NGERH0002BGZZ J AC Gear,Tuning Knob 264 TSPC-0029BGZZ J Label,Specifications [GL]
218 LANGG0001BGFW J AB Guide,Dial Pointer [For Australia]
219 HDECQ0005BGSA J AC Cap,Volume Knob 264 TSPC-0030BGZZ J Label,Specifications [BK]
220 JKNBK0001BGSB J Knob,Volume [For Australia]
221 LHLDW1033CE00 J Nylon Band 266 PRDAR0002BGFW J Heat Sink,Sub
222 JBTN-0001BGSB J AC Button,Record [Tape 1] [BK] 267 GCABC1003BGSA J Top Cabinet [GL]
222 JBTN-0001BGSC J Button,Record [Tape 1] [GL] 267 GCABC1003BGSB J Top Cabinet [BK]
223 JBTN-0002BGSB J AC Button,Play [Tape 1] [BK] 268 GFTAT1001BGSA J CD Lid [GL]
223 JBTN-0002BGSC J Button,Play [Tape 1] [GL] 268 GFTAT1001BGSB J CD Lid [BK]
224 JBTN-0003BGSB J AC Button,Rewind [Tape 1] [BK] 269 HPNLZ1001BGSA J Panel,Decoration
224 JBTN-0003BGSC J Button,Rewind [Tape 1] [GL] 270 HPNLZ1002BGSA J Panel,LCD
225 JBTN-0004BGSB J AC Button,Fast Forward [Tape 1] 271 JBTN-0024BGSA J Button,CD Lid Open [GL]
[BK] 271 JBTN-0024BGSB J Button,CD Lid Open [BK]
225 JBTN-0004BGSC J Button,Fast Forward [Tape 1] 272 MLEVP0003BGZZ J Lock Lever,CD Lid
[GL] 273 JKNBK0002BGSA J Button,Function
226 JBTN-0005BGSB J AC Button,Stop/Eject [Tape 1] [BK] 274 LHLDM1001BGZZ J Stabilizer
226 JBTN-0005BGSC J Button,Stop/Eject [Tape 1] [GL] 275 PMAGF0001BGZZ J Magnet
227 JBTN-0006BGSB J AC Button,Pause [Tape 1] [BK] 276 LHLDZ1003BGZZ J Holder,LCD
227 JBTN-0006BGSC J Button,Pause [Tape 1] [GL] 277 MSPRD0002BGFJ J Spring,CD Lid
228 JBTN-0007BGSB J AC Button,Reverse Mode [Tape 2] ! 278 QFSHD0017CEZZ J Holder,Fuse
[BK] ! 279 QFSHD0018CEZZ J Holder,Fuse
228 JBTN-0007BGSC J Button,Reverse Mode [Tape 2] 280 MSPRB0003BGFW J Spring,CD LID Open Button
[GL] 300 CMECB0001BG01 J BL Tape Mechanism Ass’y
229 JBTN-0008BGSB J AC Button,Play [Tape 2] [BK] 300- 1 92L192104309 J Pinch Roller Arm Ass’y
229 JBTN-0008BGSC J Button,Play [Tape 2] [GL] 300- 2 92L195904302 J Pinch Roller Arm Ass’y,Rewind
230 JBTN-0009BGSB J AC Button,Rewind [Tape 2] [BK] 300- 3 92L195904301 J Pinch Roller Arm Ass’y,Fast
230 JBTN-0009BGSC J Button,Rewind [Tape 2] [GL] Forward
231 JBTN-0010BGSB J AC Button,Fast Forward [Tape 2] 300- 4 92L6201-01-111 J Head,Record/Playback,Tape 1
[BK] 300- 5 92L6209-10-10 J Head,Erase,Tape 1
231 JBTN-0010BGSC J Button,Fast Forward [Tape 2] 300- 6 92L6216-07-01 J Head,Playback,Tape 2
[GL] 300- 7 92L19210703 J FF/REW Belt
232 JBTN-0011BGSB J AC Button,Stop/Eject [Tape 2] [BK] 300- 8 92L182112173 J Main Belt,Tape 1
232 JBTN-0011BGSC J Button,Stop/Eject [Tape 2] [GL] 300- 9 92L182112142 J Main Belt,Tape 2
233 JBTN-0012BGSB J AC Button,Direction [Tape 2] [BK] 300-10(M501) 92L1959123012 J Motor with Pulley [Tape]
233 JBTN-0012BGSC J Button,Direction [Tape 2] [GL] 300-11(SW902) 92L640101149 J Switch,Leaf Type [Tape 2 Main]
234 LANGF0001BGZW J Support,Mechanism Button Shaft 300-12(SW901) 92L640101149 J Switch,Leaf Type [Tape 1 Main]
235 LHLDZ8001BG00 J AC Holder,Mic 300-13(SW903) 92L640101149 J Switch,Leaf Type [Tape 2 Play]
236 LHLDZ1002BGZZ J AC Holder,LED A 300-14(SW904) 92L64030204 J Switch,Slide Type
237 MSPRC0001BGFJ J AC Spring,Battery,- [Tape 2 Direction]
238 PRDAR0001BGFW J AL Heat Sink,Main 601 XEBSD30P10000 J AA Screw,ø3×10mm
239 NGERK0001BGZZ J AD Dial Drum 602 XJBSD30P08000 J AA Screw,ø3×8mm
240 PSHEP0001BGSA J AD Sheet,LED,Left 603 XBPSD26P04JS0 J Screw,ø2.6×4mm
241 PSHEP0002BGSA J AD Sheet,LED,Right 604 XHBSD20P04000 J AA Screw,ø2×4mm
242 JKNBZ0001BGSA J AC Knob,Fine Tuning 605 XJSSD30P10000 J AA Screw,ø3×10mm
243 PCOVZ9001BGZZ J AB Cover,Dial Pointer 606 XBBSF30P10000 J AA Screw,ø3×10mm
244 MSPRP0001BGFW J AC Plate,Record 607 XJBSD40P16000 J AB Screw,ø4×16mm
245 GCABB1003BGSA J Rear Cabinet [GL] 608 XEBSD30P20000 J AA Screw,ø3×20mm
245 GCABB1003BGSB J Rear Cabinet [BK] 609 XHSSF30P06000 J AA Screw,ø3×6mm
246 GLEGG0001BG00 J AB Cushion,Leg 610 XEBSD30P10000 J AA Screw,ø3×10mm
247 JHNDP1002BGSA J Handle [GL] 611 LX-JZ0002AWFD J AA Screw,ø3×10mm
247 JHNDP1002BGSB J Handle [BK] 612 XESSD30P10000 J Screw,ø3×10mm
248 LHLDQ1001BGZZ J AE Holder,AC Socket/Voltage 613 LX-EZ0005AWFD J AA Screw,ø2.6×10mm
Selector
249 MSPRB0002BGFW J AB Spring,Rod Antenna SPEAKER BOX PARTS
250 MSPRC0002BGFJ J AC Spring,Battery,+/-
251 MSPRC0003BGFJ J AC Spring,Battery,+/- 301 CCAB-120LBG01G J Front Panel,Ass’y,Left [GL]
253 QANTR0002BGZZ J AK Rod Antenna 301 CCAB-120LBG01K J Front Panel,Ass’y,Left [BK]
254 LHLDR1001BGZZ J AD Holder,Tuning 302 CCAB-120RBG01G J Front Panel,Ass’y,Right [GL]
255 NGERK0002BGZZ J AB Gear,Tuning A 302 CCAB-120RBG01K J Front Panel,Ass’y,Right [BK]
256 NGERK0003BGZZ J AB Gear,Tuning B 303 GCABD1001BGSB J AQ Speaker Box,Left [BK]
257 JKNBM0001BGSA J AD Button,Surround 303 GCABD1001BGSC J Speaker Box,Left [GL]
258 JKNBP0001BGSA J AA Knob,Function 304 GCABF1001BGSB J AQ Speaker Box,Right [BK]
259 JKNBP0001BGSA J AA Knob,Dubbing Speed 304 GCABF1001BGSC J Speaker Box,Right [GL]
260 JKNBP0002BGSA J AB Knob,Band Selector 305 GLEGG0001BG00 J AB Cushion,Leg,Speaker
261 LHLDS1002BGZZ J AC Holder,Record Lever 306 LHLDW1001BGSB J AB Holder,Speaker Cord [BK]
262 MLEVP0002BGZZ J AB Lever,Record 306 LHLDW1001BGSC J Holder,Speaker Cord [GL]
263 GFTAB1001BGSB J AE Battery Compartment Lid [BK] 307 QCNWG0001BGZZ J AE Cord,Speaker
263 GFTAB1001BGSC J Battery Compartment Lid [GL] 308 LPLTW0001BGZZ J AC Support H,Speaker Box
264 TSPC-0017BGZZ J Label,Specifications [GL] 309 LPLTW0002BGZZ J AC Support V,Speaker Box
[For Malaysia/Asia Middle East/ 701 XEBSD30P10000 J AA Screw,ø3×10mm
Africa] 702 XJBSD40P16000 J AB Screw,ø4×16mm
264 TSPC-0018BGZZ J Label,Specifications [GL] SP401,402 VSP0012PBG28A J Speaker,Woofer
[For Jordan/Egypt] SP403,404 RALMB0001BGZZ J AC Speaker,Tweeter
264 TSPC-0020BGZZ J Label,Specifications [GL]
[For Thailand]
–4–

GX-CD1200W
PRICE PRICE
RANK RANK
ACCESSORIES/PACKING PARTS
! QACCA0001SJ00 J AS AC Power Supply Cord
! QACCE0007AW00 J AH AC Power Supply Cord
! QACCL0002AW00 J AN AC Power Supply Cord
! QPLGA0250AFZZ J AF Adaptor,AC Plug
! QPLGA0253AFZZ J AE Adaptor,AC Plug
SPAKA0003BGZZ J Packing Add.,Unit
SPAKC0023BGZZ J Packing Case [GL]
[For Malaysia]
SPAKC0024BGZZ J Packing Case [GL]
[Except for Malaysia]
SPAKC0033BGZZ J Packing Case [BK]
[For Malaysia]
SPAKC0034BGZZ J Packing Case [BK]
SSAKA0002BGZZ J AB Polyethylene Bag,AC Plug
Adaptor
SSAKH0002BGZZ J AB Polyethylene Bag,Accessories
SSAKH0004BGZZ J AB Polyethylene Bag,Unit
SSAKH0005BGZZ J AB Polyethylene Bag,Speaker
TGANE0002BG03 J Warranty Card [For Philippines]
TGANE0003BGZZ J Warranty Card [For Australia]
TINSZ0008BGZZ J Operation Manual
TLABB0001BGZZ J AB Label,Japan
TLABB0002BGZZ J AC Label,Japan
TLABE0005BGZZ J Label,Ean Bar Code [GL]
TLABE0008BGZZ J Label,Ean Bar Code [BK]
TLABR1137BGZZ J Label,Bar Code [GL]
TLABR1138BGZZ J Label,Bar Code [BK]
TLABS0002BGZZ J Label,Laser
TLABS0003BGZZ J Label,Class 3
TLABZ0001BGZZ J Label,Contru origin for Set
TLABZ0002BGZZ J Label,Contru origin for P-case
TLABZ0009BGZZ J Label,Feature,Left [For Malaysia]
TLABZ0010BGZZ J Label,Feature,Right
[For Malaysia]
TLABZ0011BGZZ J Label,Feature,Left
TLABZ0012BGZZ J Label,Feature,Right
P.W.B. ASSEMBLY (Not Replacement Item)

PWB-A1~8 DUNTK0003BG01 J — Main/Graphic Equalizer/Volume/
Fine Tuning/Terminal A/
Terminal B/Power/Holder
(Combined Ass’y)
PWB-B QPWBF0027AWZZ J AD CD Motor (PWB Only)
PWB-C1~3 DUNTK0004BG01 J — CD Servo/CD Control/Switch
(Combined Ass’y)
OTHER SERVICE PART

UDSKA0004AFZZ J AZ Pickup Lens Cleaner
–5–

GX-CD1200W
A
307
306
B
701
304
701
C 704
302
702
D 301
303
703x2
E
M802
305
M801
305x2
G SW702
PWB-B
1 2 3 4 5 6
Figure 6 CD MECHANISM EXPLODED VIEW
–6–

GX-CD1200W
269
247
271
CD
MECHANISM 610x2
A
278 268
277 263
275
267 274
608x3
245 253
PWB-C2 264
613x3
B 273 606
612x3
276
601x3 LCD801 PWB-C3
272
214
607
SW601 609
PWB-C1
248
601x3
C
SO601
250
607x3 T601
251
PWB-A6 246x2 246
607x2
249
609
279 237 246
601x2 280
D 251
PWB-A7 PWB-A5 611
601 601
601 255
601x2 603
213 236 239
605x5
270 PWB-A2 256 Silicon
Grease
241
254
MIC151 240
601x2 602
211
201 601 266
235
PWB-A8
218
E 204 Silicon
258 Grease
238
PWB-A3 VR401
601 PWB-A1
243 259 IC502
260
602x2
257 601x2
205
Q601 IC402 602x2
214x2 261
601
F
605x6
213 244 604
242
262 TAPE
216
601 MECHANISM
212
210 222
206 223
PWB-A4 224
225
226 227
202 228
With VR401 203 229
G 230
231 234x2
232
233
207
300(300-1, 300-2, 300-3,
300-4, 300-5, 300-6, 300-7,
220 300-8,300-9,300-10(M501),
219 300-11(SW902),
208
300-12(SW901),
215 300-13(SW903),
221
300-14(SW904)
215 209
Note: Only the unit and consumale parts are supplied as parts supply for the Tape mechanism.
1 2 3 4 5 6
Figure 7 CABINET EXPLODED VIEW
–7–

GX-CD1200W
702x5
A
303(LEFT)
301(LEFT) 304(RIGHT)
302(RIGHT)
SP403(L-CH) 307
SP404(R-CH)
B
701x4
306
308
D
305 SP401(L-CH)
SP402(R-CH) 309 305 305
305
TWEETER
SP403(L-CH)
E SP404(R-CH)
BLACK RED
BLACK
RED
F TWEETER
SP403(L-CH)
SP404(R-CH)
G WOOFER
SP401(L-CH)
SP402(R-CH)
WOOFER
SP401(L-CH)
SP402(R-CH)
1 2 3 4 5 6
Figure 8 SPEAKER EXPLODED VIEW

–8–

GX-CD1200W
—MEMO—
–9–

GX-CD1200W
—MEMO—
– 10

GX-CD1200W
COPYRIGHT © 2000 BY SHARP CORPORATION

ALL RIGHTS RESERVED.
No part of this publication may be reproduced,

stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
Communication Systems Group
Quality & Reliability Control Center
Higashihiroshima, Hiroshima 739-0192, Japan
Printed in Japan
A0006-1408DS•HA•I
SCA • SCNZ • EX

Service Manual: GX-CD1200W (BK) GX-CD1200W (GL)

Uploaded by

Copyright:

Available Formats

Service Manual: GX-CD1200W (BK) GX-CD1200W (GL)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: GX-CD1200W (BK) GX-CD1200W (GL)

Uploaded by

Copyright:

Available Formats

GX-CD1200W

This document has been published to be used

Downloaded from www.Manualslib.com manuals search engine

AC POWER SUPPLY CORD AND AC PLUG ADAPTOR

QACCL0002AW00 QPLGA0250AFZZ QPLGA0253AFZZ

FITTING OF DIAL POINTER

Make the minimum space.

Downloaded from www.Manualslib.com manuals search engine

38. FM/SW Telescopic Rod Aerial 38

Downloaded from www.Manualslib.com manuals search engine

Main PWB Rear Cabinet Voltage Selector

Downloaded from www.Manualslib.com manuals search engine

CD Player Unit Speaker

REMOVING AND REINSTALLING THE MAIN PARTS

Downloaded from www.Manualslib.com manuals search engine

How to remove the motor (See Fig. 6-4.)

How to remove the belts (See Fig. 6-5.) Figure 6-2

Downloaded from www.Manualslib.com manuals search engine

MECHANISM SECTION TUNER SECTION

• Tape Speed (Normal only) MW Band fL: L6 Input: Antenna

Figure 7 VCO FREQUENCY TEST CIRCUIT

Downloaded from www.Manualslib.com manuals search engine

Figure 8 ADJUSTMENT POINTS

Downloaded from www.Manualslib.com manuals search engine

LASER LIGHTING CONFIRMATION

10 1 1 100 R835 C850

Downloaded from www.Manualslib.com manuals search engine

SW1 fH TC6 SW1

FM IF 1 3 C24 CF3 C38

27K 27K 0.022 C43 C42

2 4 ( ):HIGH R168 DUBBING

4.7K C154 R169 NORMAL

PLAYBACK HEAD (ML) 6.8K

SW504-A 0.01 KRC102M 0V

C105 R107 82K

L-CH 180K 120K 330P 4.7/50

R P R P 330P 180K R122 R114 330P

SW504-B SW101-D SW101-C C106 10K 4.7/50

SW101-B 330P C124

1 1 0.015 R110 R123 100

TAPE1 22mH 0.0015(ML) ( ):RECORD SW

L301 C303 SW101-E

MAIN PWB-A1/VOLUME PWB-A3/FINE TUNING PWB-A4

• NOTES ON SCHEMATIC DIAGRAM can be found on page 18.

Downloaded from www.Manualslib.com manuals search engine

GRAPHIC EQUALIZER PWB-A2 IC202 LB1403N

0.001 4.7/50 6.9V

R405 R407 R417

R412 C415 0V SP401

2.7K 12K 22K R427 0V 2.2

C407 R413 0.6V -OUT1 R435

4.7/50 10K 3.3K C418 0V C427 2.2

R420 0.1(ML) R434

C408 100K 0V +OUT2

4.7/50 0.6V 2.2 8 Ohm

R404 R410 0V -OUT2 R436

3.8V 2 3.8V 1/50 (ML) 1K 8 Ohm

Figure 11 SCHEMATIC DIAGRAM (2/4)

Downloaded from www.Manualslib.com manuals search engine