DSC-H5

SERVICE MANUAL LEVEL 2

US Model
Ver. 1.0 2006. 04 Canadian Model
Revision History AEP Model
UK Model
How to use E Model
Acrobat Reader Australian Model
Chinese Model
Internal memory
Brazilian Model
ON BOARD Hong Kong Model
Korea Model
Tourist Model
Japanese Model
Link

SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS

SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST

DISASSEMBLY SCHEMATIC DIAGRAMS

• Precaution on Replacing the SY-150 board

Note : Note :
The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.

DIGITAL STILL CAMERA

2006D1600-1
DSC-H5_L2 ©2006.04
9-852-117-31 Sony EMCS Co. Published by DI Technical Support Department
 These specifications are extracted from User’s Guide/
Troubleshooting of DSC-H5 (2-673-176-11 (1)).

SPECIFICATIONS

Camera [Input and Output connectors] Dimensions 113.2×83.0×94.0 mm

(4 1/2 inches × 3 3/8 inches ×
[System] A/V OUT jack (Monaural) 3 3/4 inches) (W/H/D,
Minijack excluding protrusions)
Image device 7.20 mm (1/2.5 type) color Video: 1 Vp-p, 75 Ω,
CCD, Primary color filter unbalanced, sync negative Mass Approx. 554 g (1 lb 3.5 oz)
Total pixel number of camera Audio: 327 mV (at a 47 kΩ (including two batterries,
Approx. 7 410 000 pixels load) shoulder strap, adaptor ring,
Effective pixel number of camera Output impedance 2.2 kΩ lens hood, lens cap, etc.)
Approx. 7 201 000 pixels USB jack mini-B Microphone Electret condenser microphone
Lens Carl Zeiss Vario-Tessar Speaker Dynamic speaker
12× zoom lens USB communication
f = 6.0 – 72.0 mm (36 – Hi-Speed USB (USB 2.0 Exif Print Compatible
432 mm when converted to a compliant) PRINT Image Matching III
35 mm still camera) [LCD screen] Compatible
F2.8 – 3.7
PictBridge Compatible
Exposure control Automatic exposure, Shutter LCD panel 7.5 cm (3.0 type) TFT drive
speed priority, Aperture Total number of dots
priority, Manual exposure,
BC-CS2A/CS2B Ni-MH battery charger
230 400 (960×240) dots
Scene Selection (7 modes) Power requirements
[Finder] AC 100 to 240 V, 50/60 Hz,
White balance Automatic, Daylight, Cloudy,
Fluorescent, Incandescent, Panel 0.5 cm (0.2 type) color 3W
Flash, One push
Total number of dots Output voltage AA: DC 1.4V 400 mA × 2
File format (DCF compliant) Approx. 200 000 dots AAA: DC 1.4 V 160 mA × 2
Still images: Exif Ver. 2.21 equivalent Operating temperature
JPEG compliant, DPOF 0 to +40°C (+32 to +104°F)
compatible [Power, general]
Storage temperature
Movies: MPEG1 compliant Power HR 15/51:HR6 (size AA) –20 to +60°C (–4 to +140°F)
(Monaural) Nickel-Metal Hydride batteries
(2), 2.4 V Dimensions Approx. 713091 mm
Recording media Internal Memory (30 MB)
(2 7/8×1 3/16×3 5/8 inches)
“Memory Stick Duo” LR6 (size AA) alkaline (W/H/D)
Flash Flash range (ISO set to Auto): batteries (2), 3 V
Mass Approx. 90 g (3 oz)
approx. 0.3 m to 9.0 m (11 7/ ZR6 (size AA) Oxy Nickel
8 inches to 29 feet 6 3/8 inches) Primary Battery (2), 3 V
(W)/approx. 0.9 m to 6.8 m Design and specifications are subject to change
(35 1/2 inches to 22 feet 3 3/ AC-LS5K AC Adaptor 4.2 V without notice.
4 inches) (T) Power consumption (during shooting with the
Viewfinder Electric viewfinder (color) LCD screen)
1.4 W
Operating temperature
0 to 40°C (32 to 104°F)
Storage temperature
–20 to +60°C (–4 to +140°F)

DSC-H5_L2
—2—
 SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point : LEAD FREE MARK
them out to the customer and recommend their replacement. Unleaded solder has the following characteristics.
4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than
of deterioration. Point them out to the customer and ordinary solder.
recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified.
Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350°C.
• Keep the temperature of the soldering iron around 270˚C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
• Do not touch the soldering iron on the same conductor of the • Strong viscosity
circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than
• Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such
or unsoldering. as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

DSC-H5_L2
—3—
 TABLE OF CONTENTS

1. SERVICE NOTE
1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY ······ 1-1
1-2. METHOD FOR COPYING OR ERASING THE DATA IN
INTERNAL MEMORY ·················································· 1-2
1-3. PRECAUTION ON REPLACING THE SY-150
BOARD ··········································································· 1-3
1-4. VIDEO OUT DEFAULT DATA CHECK ······················· 1-3
1-5. INITIAL LANGUAGE DATA CHECK ·························· 1-3

2. DISASSEMBLY
2-1. DISASSEMBLY ······························································ 2-3

3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2) ··························· 3-1
3-2. OVERALL BLOCK DIAGRAM (2/2) ··························· 3-2
3-3. POWER BLOCK DIAGRAM (1/2) ································ 3-3
3-4. POWER BLOCK DIAGRAM (2/2) ································ 3-4

4. PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM ································ 4-1
4-2. SCHEMATIC DIAGRAMS ············································ 4-5
4-3. PRINTED WIRING BOARDS ····································· 4-25
4-4. MOUNTED PARTS LOCATION ································· 4-32

5. REPAIR PARTS LIST

5-1. EXPLODED VIEWS ······················································ 5-3
5-2. ELECTRICAL PARTS LIST ········································ 5-10

DSC-H5_L2
—4—
 1. SERVICE NOTE

1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY

Self-diagnosis display
• C: ss: ss
The contents which can be handled
by customer, are displayed.
• E: ss: ss
The contents which can be handled
by engineer, are displayed.

Display Code Countermeasure Cause Caution Display During Error

C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR
Format the “Memory Stick” or internal “Memory Stick” or internal memory is
FORMAT ERROR
memory. unformatted.
C:13:ss Insert a new “Memory Stick”. “Memory Stick” is broken. MEMORY STICK ERROR

Turn the power off and on again. Trouble with internal mamory. INTERNAL MEMORY ERROR
When failed in the focus zoom
E:61:ss Checking of lens drive circuit.
initialization.
Inspect angular velocity sensor
E:62:ss Steady shot function does not work well.
peripheral circuits. _
Checking of flash unit or replacement Abnormality when flash is being
E:91:ss
of flash unit. (Note) charged.
E:92:ss Insert a batteries correctly. Batteries are pack is not inserted correctly.

Note : After repair, be sure to execute the “Initialize” of the setup screen.

DSC-H5_L2
1-1
 1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)

Note: 1 When replacing the SY-150 board, erase the data in internal memory of the board before replacement.
Note: 2 When replacing the SY-150 board or the IC202 on the SY-150 board, execute formatting and initialize the internal memory after
replacement.

Method for copying the data in internal memory

Copy

Copies all images in the internal memory to a “Memory Stick Duo”.

OK See the following procedure.
Cancel Cancels the copying.

1 Insert a “Memory Stick Duo” having 32 MB or larger capacity.

2 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.
3 Select [OK] with v, then press z.
Copying starts.

Copying
102_COPY

• Use a fully charged Nickel-Metal Hydride battery or the AC Adaptor (not supplied). If you attempt to
copy image files using a batteries with little remaining charge, the batteries may run out, causing copying
to fail or possibly corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in
(Internal Memory Tool).
• You cannot select a folder copied on a “Memory Stick Duo”.
• Even if you copy data, a (Print order) mark is not copied.

Method for formatting the internal memory

This item does not appear when a “Memory Stick Duo” is inserted in the camera.
The default settings are marked with .

Format

Formats the internal memory.

• Note that formatting irrevocably erases all data in the internal memory, including even protected images.

OK See the following procedure.

Cancel Cancels the formatting.

1 Select [OK] with v on the control button, then press z.

The message “All data in internal memory will be erased Ready?” appears.
2 Select [OK] with v, then press z.
The format is complete.

• PROCESS AFTER FIXING FLASH ERROR

When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.

Method for Initializing the Flash Error Code

Initialize

Initializes the setting to the default setting.

OK See the following procedure.
Cancel Cancels the resetting.

1 Select [OK] with v on the control button, then press z.

The message “Initialize all settings Ready?” appears.
2 Select [OK] with v, then press z.
The settings are reset to the default setting.
Make sure that the power is not disconnected during resetting.

DSC-H5_L2
1-2
 1-3. PRECAUTION ON REPLACING THE SY-150 BOARD
• The Repair Board has already been adjusted. Re-initialization or EVR data copy from the set before repair is not
required.
• Perform “VIDEO OUT Default Data Check” and “Initial Language Data Check” mentioned below, and also the
adjustment items necessary after SY Board replacement.

1-4. VIDEO OUT DEFAULT DATA CHECK

When you replace to the repairing board, the written data of repairing board also might be changed to original setteing
because of broadcast system (NTSC/PAL).
When the data has changed because of board replaceing etc., check the default data of VIDEO OUT if destination code
is right. If not, rewrite to the right value.

VIDEO OUT Default Data

Data
Page Address
NTSC PAL
4F 8D 00 01

Writing Method:
1) Select page: 00, address: 01, and set data: 01.
2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL).
3) Select page: 40, address: 38, and set data: 00.
4) Click [Save] on the SEUS screen.
5) Select page: 80, address: 34, and check that the data is “00”.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.

1-5. INITIAL LANGUAGE DATA CHECK

If the SY-150 board was replaced, initial language setting may be changed. Accordingly, change the following data so
as to set same initial language as that of the set distributing in each region.

Initial language: Language displayed at the next starting if the setting of Setup menu was reset.
It is different from the language setting selectable with the menu.

Initial Language Data

Page Address Data Language GP1 GP2 GP3 GP4
00 English z z z
01 Japanese z
04 Spanish z z
4F 8C
08 Simplified Chinese z
0B Russian z
0D Korean z
Note: GP1 is fixed to Japanese.
GP2 is fixed to English.
GP3 is either English, Spanish, or Russian.
GP4 is either English, Spanish, Simplified Chinese, or Korean.

Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8C, and set the Initial Language Data.
3) Select page: 40, address: 38, and set data: 00.
4) Click [Save] on the SEUS screen.
5) Select page: 80, address: 34, and check that the data is “00”.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
8) Turn off the camera.
9) Turn on the camera. Execute “Initialize” of Setup screen.
10) Check the language displayed when the camera starts.

DSC-H5_L2
1-3E
 2. DISASSEMBLY

Link

DISASSEMBLY

HELP

COMMON NOTE FOR DISASSEMBLY

DSC-H5_L2
 2. DISASSEMBLY

2. DISASSEMBLY

NOTE FOR REPAIR

Make sure that the flat cable and flexible board are not cracked of When remove a connector, don't pull at wire of connector.
bent at the terminal. Be in danger of the snapping of a wire.
Do not insert the cable insufficiently nor crookedly.

When installing a connector, don't press down at wire of connector.

Be in danger of the snapping of a wire.

Cut and remove the part of gilt

which comes off at the point.
(Take care that there are
some pieces of gilt left inside)

DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR

The charging elect capacitor 320uF (330V) is charged up to the Discharging the Capacitor
maximum 300 V potential. Short circuits between the positive and the negative terminals of
There is a danger of electric shock by this high voltage when the charged capacitor with the short jig about 10 seconds.
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-H5 is simply turned off. Therefore, the
remaining voltage must be discharged as described below. Short jig (1kΩ/1W)

Preparing the Short Jig

To preparing the short jig. a small clip is attached to each end of ST-142 board
a resistor of 1 kW /1 W (1-215-869-11)
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.

1 kΩ/1 W Capacitor

Wrap insulating tape.

ST-142

DSC-H5_L2
2-1
 2. DISASSEMBLY
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY

8
-
SW 7
1
47 1

-
SW1 6
4 7
5
2

3
1

1 Three screws (M1.7x4) 1 Two claws 4 Two claws, two dowels

2 Three screws (M1.7x4) 2 Flexible board (from the LCD unit) 5 Claw, two dowels
3 Cabinet (rear) section 3 Flexible board 6 Two tapping screws (M1.7x3.5)
(from the light guide plate (3.0) block) 7 SW-478 flexible board
8 SW-471 board

Note: Be very careful not to

damage the flexible board.

7
8
1

A (See page 2-4)

0
-15
SY 5 6 B (See page 2-4)
2 4

0 3
2 -15
SY
66
5 9
1 Fuse replacement caution label
3 2 Flexible board (from the lens section)
3 Tape CD retainer (420) 7
3 4
1 Two claws 4 CD-621 flexible board SY-150
5 AF-105 flexible board HELP 01 8
2 Two tapping screws (M1.7x3.5) qa
6 Flexible board (from the lens section) 2 1 6
3 LCD frame
1
7 Control switch block q;
8 Flexible flat cable (ST-003) q;
9 From the microphone
q; Tapping screw (M1.7x5)
qa Main section

DSC-H5_L2
2-3
 2. DISASSEMBLY

4
1
2 3
Refer to page 2-1 "DISCHARGING 1 3
6
2 OF THE FLASHLIGHT POWER
SUPPLY CAPACITOR, when
1 discharging the capacitor. 2
7
4
8 HELP 04
5
9
3 HELP 07 HELP 05 HELP 06

HELP 08

1 Turn the flexible board. 1 Claw

1 Two tapping screws (M1.7x4) 1 Tapping screw (M1.7x4)
2 Tapping screw (M1.7x5) 2 Three harnesses (HA-001) (Red, White, Blue)
2 Control switch block 2 Microphone holder
3 Lens section 3 Open the ST cover in the direction of the arrow.
3 Microphone cushion (B)
4 Microphone 4 ST section
5 Microphone cushion
6 Tapping screw (M1.7x4)
7 AF-105 flexible board
8 Tapping screw (M1.7x4)
9 AF holder

3
1 5
5 4 HELP 03

6
3
3
2 6
2
1

0 1 S-
M05
50 -15 3
-1 SY
SY
HELP 02 2
4

7
8 1 Flexible flat cable (MS-030)
2 Two tapping screws (M1.7x4)
3 MS-305 board
1 Two claws 1 Battery connector 5 Flexible flat cable (MS-030) 4 Battery connector
2 Flexible board (from the LCD module) 2 From the loudspeaker 6 SW-478 flexible board 5 Three claws
3 EVF section 3 JK-306 flexible board 7 CK-161 flexible board 6 Battery terminal board
4 Two tapping screws (M1.7x4) 8 SY-150 board

DSC-H5_L2
2-4E
 HELP
Disassembling and assembling procedures that require attention are described here.

HELP 01
When attaching the fuse replacement caution label to the SY-150 board,
cover the harness of the loudspeaker with the fuse replacement caution label.

Fuse replacement
caution label

Harnesses of
the loudspeaker

HELP 02
When installing the loudspeaker, route the harnesses of the loudspeaker as shown in the figure.

Harnesses of
the loudspeaker
Loudspeaker (1.0cm)

Bend the harnesses of the

loudspeaker at the route
of the connector.

HELP 03

When installing the battery terminal board, route the harnesses of the
battery terminal board as shown in the figure.

The harnesses in the area A The harnesses in the area C must be

must be kept below surface B. kept within the D lines.
Bend the harness at portion E so that
Battery terminal the harness runs along line F.
surface B
board
Harnesses of the battery
Harnesses of the battery
terminal board
terminal board
C E

A F
D

DSC-H5_L2
HELP
 HELP 04 HELP 05

When installing the ST section, route the When installing the ST section, route the
Harness (HA-004) (Blue) ,Harness (HA-004)(White), Harness (HA-004) (Blue) ,Harness (HA-004)(White),
and Harness (HA-004) (Red) as shown in the figure. and Harness (HA-004) (Red) as shown in the figure.

Route the harnesses with the ST cover closed. ST section Harness (HA-004) (Blue) ,
Harness (HA-004)(White), ST section
Harness (HA-004) (Red)

Harness (HA-004) (Blue)

Harness (HA-004) (White)

Harness (HA-004) (Red)

HELP 06
4
1 Harness (H-004) (Red)
5
9 2 Harness (H-004) (White)
3 Harness (H-004) (Blue)
4 Flash unit, ST-144 board
5 Apply the soldering in three points.
q;
6 ST-142 board
7 Apply the soldering in three points.
8 ST cover
9 Two claws
2White 8 q; Tapping screw (M1.7x4)

3Blue
Solder each harness according to the color
1Red
( Red, White, Blue) as shown in the figure.

Solder each harness according to the color 6

( Red, White, Blue) as shown in the figure.
ST-142 board
ST-144 board

Blue Blue
Red White
White
7

Red

DSC-H5_L2
HELP
 HELP 07

Microphone holder
Install the microphone tilted as
shown in the figure below. Microphone cushion (B)

Microphone
holder
Microphone
Microphone Microphone
cushion (B) Microphone cushion
Microphone cushion

HELP 08

When removing the lens ring, remove the screw and strap sheet metal (R) first. 1 Tapping screw (M1.7x4)
Slide the cap lever in the direction of arrow A while taking care that the cap
lever is not caught on the notch of the lens ring. 2 Strap sheet metal (R)
Remove the lens ring by turning it in the direction of arrow B.

Cap lever

Cap lever 3 Lens ring

Lens ring
A

Notch of the
lens ring

DSC-H5_L2
HELP
 3. BLOCK DIAGRAMS

Link

OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (1/2)

OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2)

DSC-H5_L2
 3. BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

LENS UNIT CD-621 FLEXIBLE MS-030 FLEXIBLE

CD-617 BOARD SY-150 BOARD (1/2) FLAT CABLE
IRIS BOARD
SHUTER

CN301 4,3,5,7,2,8
K5,G4,H4,L5 AC4,AE4 CN302
22 4,3,5, 4,3,5,
H2,H1,J1,J2 AE5,AC5 MS D0-MS D3, MS BS, MS CLK
| CA AD0 - CA AD13 7,2,8 7,2,8
IC002 CCD OUT
S/H 35 M5,J4,K4,M6
K2,K1
AB6,AF6
XMS IN 6
MEMORY
STICK Duo
CCD IMAGER 15 1 IC001 3 20 20 6
A/D CONV.
X101
12MHz
(3/8) 6 6 CONNECTOR
CN706
(2/8)
BUFFER
IC101
XTAL OSC EXTAL
1-14
27,28
24 23
A6
MS-305
19-17
VSUB CP301
V1
V2
V7
V8 H1A,B Q001
1 1 21
TIMING
(1/2) BOARD
V3A,B V9 H2A,B GENERATOR CLK TGO CAMERA DSP
RANDOM TRIGGER 47 E1
V4 V10 RG VSUB 4 4 36
V5A,B VST,
V6 VHLD CN001 D21,D22,D20,B22,A22,A23
CN001 CN301 45 CA HD, CA FD H5
B23,E20,E21,B24,A24,A25
46 J5
26-39 12,10,8,6,14 2 B25,C25,C26,B26,E10,A10
D10,E11,B10,A11,B11,E12 D0-D31 (4/8)
XCS_FE D11,D12,F12,B12,A12,E13
39 U22
26-39 12,10,8,6,14 2
CN301 1
D13,D14
IC203 CK-161
|
5
Q301
VSUB_CONT_POST
T4
D17,D18,D16,B18,A19
B19,E16,D19,E19,E17 A0-A11
256Mbit
SDRAM BOARD
VSUB VSUB_CONT_PRE B20,A20
7 R23 CN707 CN001
| XSAN_RST_OUT
42 D8,D7,E8
20 20 12
E7,D6,D5 LCD D0-D7 LCD D0-D7 | LCD D0-D7 |
40, 41 E6,B4 13 19 LCD9001
LCD HD 3.0 INCH
E9 LCD VD 11 21
IRIS A DIR2A DIR2A COLOR LCD
(1/8) B8 10 22
IRIS IRIS XA BRK2A BRK2A PANEL
LCD CK

SAN1 SO,SCK
MOTOR F2 F5 DIR2B N4 D9 12 20
1
IRIS B
IRIS XB E2 IC401 E5
DIR2B
BRK2B BRK2B P6
M 4 D2
(1/2) D3
P4
R2
U2
SAN1 SO, SCK SAN1 SO, SCK
22 10
B1 F1 MSHUT DIR R6 23 9
SHUTTER
IRIS DRIVE MSHUT EN R25
MOTOR SHUTTER + MSHUT DIR XSAN RST OUT
8 R5 AF4 24 8
SHUTTER- FC DIR A
M 5
F3
F4 SHUTTER DRIVE
G1
E4
MSHUT EN
FC DIR B
L2
FOCUS A FC EN
FOCUS N5
FOCUS XA FC DIR A
MOTOR D5 L4
FOCUS B D6 FC DIR B ZM DIR A XMS IN
9 FOCUS XB A6
M 16
E6
B7
FOCUS MOTOR
DRIVE B6
FC EN ZM BRK A N6
N2
C5 FC SENS
C6 U4 CN703
ZM SENS 1ST
ZOOM ZM SENS 2ND U5 15
MOTOR ZOOM + ZM DIR A V4 |
ZM DC FG 1A 12
36 ZOOM -
M 39
B4
B5
ZOOM MOTOR
DRIVE
A2
B2
ZM BRK A ZM DC FG 1B V5
W4
LCD D0-D7 10
|
LCD9002
LENS TEMP COLOR EVF
7
J25 LCD HD UNIT
LCD VD 18
FOCUS RESET FC SENS 17
22
SENSOR LCD CK
19
ZOOM RESET ZM SENS 1ST
24 6
SENSOR 1ST B4 B5 A2 SAN1 SO, SCK with in
4
BACK LIGHT
ZOOM RESET ZM SENS 2ND
25 (4/8) (4/8) XSAN RST OUT
SENSOR 2ND 20
ZM DC FG 1A
ZOOM DC FG
32
31
ZM DC FG 1B IC201 IC202 Y26
XCS_AUDIO
E4 (5/8)

18
LENS TEMP
BURST
FLASH MEMORY
ONE NAND
FLASH MEMORY SAN1 SO, SCK
F3 IC602
LENS TEMP E3 CN602
SENSOR
CN401
AUIN MIC SIG
L26 E6 MIC AMP B6 2 MIC MIC9001
A01-A21 A01-A16
ACTIVE LENS ACTUATOR SP+
PITCH + D0-D15 D0-D15
A5 1 SP- SP9001
11 PITCH - C1 SPEAKER AMP
PITCH B1 AB13,AA13,AE13,AF13,AF12 A2 2 SPEAKER
10 D1 XSAN RST OUT AE12,AA12,AC12,AC11,AB12
A7 D0-D15 CN601
PITCH HALL+ (6/8) AE11,AF11,AE10,AB11,AC10 AUOUT
AB10 K26 E5 D1
7 PITCH HALL- H2
H 6 J4 IC504 AF21,AF20,AE20,AB18,AB19
AU OUT AMP
C2
YAW+ AC19,AB16,AE19,AF19,AF18 CN651
12 YAW- B10 STEADY SHOT A01-A21 AE18,AA15,AC18,AC17,AB15
YAW 3,2
13 D10 CONTROL AE17,AF17,AE16,AB14,AC16 CN001
AC1 9
AC15 USB DPP, USB DMM
YAW HALL+ AD1 8
3 SAN27M CK0 (USB)
YAW HALL- J9 SAN 27M CLK0
H 2 J7
A3
XBONOBO CPU RESET XBONOBO CPU RESET
AF9
USB VBUS
6
CN501 A6 AC25 1
XCS BONOBO XCS BONOBO XAV JACK IN
A5 Y23 U25
V OUT VIDEO AMP ON AU LINE OUT J001
H26 U23 3

SE501
A4
B4 SAN0 SO, SI, SCK TO 1 1
A/V OUT

(6/8) OVERALL 4
PITCH PITCH AD B5
8 2 G5 BLOCK DIAGRAM
SENSOR
IC506 B6
KEY BONO
(2/2)
SAN1 SO, SCK (5/8)
SE502 XMS IN V LINE OUT V LINE OUT
YAW
12
PITCH/YAW
SENSOR
18
YAW AD
J5 USB V BUS
(PAGE 3-2) 3
IC601 5 2

SENSOR AMP VIDEO AMP

6 14 19

C_RESET
JK-306
Q503

MUTE
D5
D6
FLEXIBLE
BOARD

DSC-H5_L2
3-1
 3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

ST-003 ST-142 BOARD ST-144

SY-150 BOARD (2/2) FLEXIBLE BOARD
FLAT CABLE
1 1 ST UNREG
| |
3 3 D102
T101 (RECT)
(3/8) XE H
15

IC101 R22
STRB CHG
XSTRB FULL
7
STRB CHG
XSTRB FULL
7 10
HIGH VOLTAGE
CHAGER
1
2
C105
L001
V23 6 6 9
FLASH
(2/2) AB22
STRB CHG CONT
5
STRB CHG CONT
5 6 IC101 Q101
TRIGGER
COIL UNIT
SYSTEM CONTROL
IGBT
STRB ON STRB ON FLASH XE L
R4 4 4 4 DRIVE 7
DRIVE
Q702 D001
CN701 CN101
D1.2V STRB CONT

TO
OVERALL SAN0 SO, SI, SCK (1/8)

1 BLOCK DIAGRAM
(1/2) KEY BONO IC401 CN705 AF-105 FLEXIBLE BOARD
(PAGE 3-1) USB VBUS
AA25
STRB PLUNGER ON
A1 (2/2) B3
8 STRB PLUNGER
4 RY201
7 3 PLUNGER
XMS IN
STRB PLUNGER DRIVE

XSTRB POPUP XSTRB_POPUP S201

V22 5 6 (FLASH POP UP)
XLENS COVER SENSE S001 CN201
AC23 1 (LENS COVER OPEN)

4
XAF LED
D001 (AF LED) PL-045 BOARD
BT9001 1 UNREG ST UNREG
2
BATTERY F001
TERMINAL 3 REG GND SAN0 SO
4 SAN0 SI CN704 S103
XAE LOCK SW
XSAN0 SCK AB5
CN001 SAN0 SO C5 N21 XSHUTTER SW 9
SHUTTER
CONTROL SWITCH
SAN0 SI C6 SAN0 SO, SI, SCK AA5 P23 6
XSAN0 SCK B6 Y5 BLOCK
MODE DIAL 0
XCS DD
(8/8) XCS DD A6 W23 L22 MODE DIAL 1 14
L25 12 MODE DIAL
BATT SENS
IC001 BATT SENS D4
RSTA
K25
AB23
JOG A
JOG B 11
S105

XDD RST OUT Y4 JOG DIAL

DC/DC CONVERTER XDD RST OUT A7 W22 10
R26
REAL TIME CLOCK S106,101,102 EXEC
XPWR OFF KEY AD2
XPWR OFF B7 AA23 G25 8 FINDER, FOCUS, BRK
UNREG
S108
F002 1 XPLAY SW
PLAY
XPWR LED
A8 OSC I D23 5 D102 (POWER)
EVER SRAM
X001
32.768KHz D 3.2V S104
A9 OSC O CAM 3.2V XPWR ON
3 POWER
A 3.2V
B8 VL 3V MS VCC S107
BT001 KEY BONO
CAM 2.9V 2 STEADY SHOT
LITHIUM
BATTERY PANEL 2.9V
C7 XPWR ON
(SECONDARY) D 1.8V
C9 USB VBUS M 5V
B10 XMS IN ST 5V
D 1.2V
CAM 15V CN702 S401 — S406
KEY AD0
CAM -7.5V 8 26
K23 DOWN, RIGHT, UP, LEFT, SET, DUST
D7 XPLAY SW S407 — S410
BL H
KEY AD1
BL L L23 7 27 ZOOM W, ZOOM T, MENU, DISP
LED9001
XAF LED LCD
A4 XACCESS LED
E4 1 33 D401 (ACCESS) BACK
LIGHT
30 BL H 4 6
31 3 5
32 BL L 2
2
33 1 1
CN401
CN402

SW-478
FLEXIBLE
BOARD SW-471 BOARD

DSC-H5_L2
3-2
 3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

ST-003 ST-142 BOARD

SY-150 BOARD (1/2) FLEXIBLE
FLAT CABLE T101
D102(RECT) XE H
F001 1 1 FLASH
1 UNREG ST UNREG ST UNREG | | UNIT
BT9001 15
2 3 3
BATTERY
TERMINAL 3 REG GND
STRB CHG 7 7
L101
10 IC101 1
2
C105
XSTRB FULL 6 6 9
4 HIGH VOLTAGE
CN001 STRB CHG CONT CHAGER
5 5 6
IGBT DRIVE
ST 5V
8 8 3

CN701 CN101 ST-144 BOARD

MS VCC
F002
UNREG
ST UNREG
(5/8)
(8/8) AU 3.0V

ST 5V
AU 3.0V

ST 5V L601
IC602
MS-305 IC001 PWR1-1 A1
PWR1-2 B1
MIC AMP
CAM 3.2V CAM 3.2V SPEAKER AMP
DC/DC CONVERTER PWR1-3 C2
BOARD REAL TIME CLOCK
VO1-1 F1
D 3.2V D 3.2V
AU OUT AMP

CN302 J1 UNREG1-1,2 VO1-2 F2 L001

A 3.2V A 3.2V
CN301 K1
VFB1 H2
MEMORY 9 MS VCC R002 D001
10 10 EVER SRAM LDO1 3.1V L011
STICK Duo H1 MS PWR IN (5/8)
CN706 REG.
CONNECTOR G1

BT001
VL 3V
B8 RTC BAT MS PWR
G2
MS VCC
4 IC603 3
AU 3.0V
LITHIUM 1
A8 OSC I LDO3IN 3V REG
BATTERY X001 B2
STRB CHG
MS-030 FLEXIBLE (SECONDARY)
XSTRB FULL
R22 32.768KHz
A9 OSC O 2.9V REG
FLAT CABLE V23 (3/8) LDO3 CAM 2.9V CAM 2.9V
STRB CHG CONT A2
AB22 BATT SENS
IC101 K25
Y4 XDD RST OUT
D4 DTG1
A7 XRESET
LDO2IN
B3
PANEL 2.9V

CAMERA DSP R26

SYSTEM CONTROL XPWR OFF 1.8V REG
AA23 B7 XPWR OFF LDO2 D 1.8V
A3
MS PWR ON MS PWR ON
T25 D3
UNREG2 J6
K6
XCS DD W23 A6 XCS DD
CONTROL SWITCH SAN0 SO AB5 C5 SAN0 SO PWR56 OUT J7
SAN0 SI K7
BLOCK XSAN0 SCK
AA5
Y5
C6 SAN0 SI
B6 XSAN0 SCK
LX5-1 J9 L006
LX5-2 J10 CAM 15V
LX5-3 K9 D003 Q004
TO
D102 (POWER) 5 D23 XPWR LED
LX5-4 K10 (RECT) SWITCHING & RECT
CAM -7.5V POWER
BLOCK DIAGRAM
1
VFB5 H9 (2/2)
D 3.2V 4 D 3.2V GT6 H6 L009 (PAGE 3-4)
A 3.2V VFB6 H7
AU 3.0V M 5V
VI 3.2V PWR2 D10
L003 D 1.2V
D 1.2V
MODE A 3.2V 13 LX2 C10
DIAL ST UNREG
D 1.8V SD 1.8V
S104 VFB2 D8
XPWR ON F003
POWER XPWR ON L005
3 C7 XPWRON1
S108 BL H BL H
XPLAY SW LX3 E10
PLAY XPLAY SW 1 D7 XPWRON2 D002
(RECT)
CN704 VO3 E9
L201
(4/8) LV3 BL L BL L
F9

(4/8) IC203 RS3

F8
L008
IC202 256Mbit
SDRAM Q001
Q003
SWITCH
SWITCHING M 5V
ONE NAND
FLASH MEMORY ST 5V
ST 5V
BG4 G9
(4/8) PANEL 8.5V ON
D 3.2V
AF-105 FLEXIBLE IC201 TG4 F10 MT 5V ON
D 1.8V Q002
BOARD BURST RECT PANEL 2.9V
D3.2V VFB4 F7
FLASH MEMORY
3
PSG4 G8
D001 (AF LED) XAF LED
4 A4 XAF LED PANEL 8.5V ON
CN705 PORTB C4 (5/8)
MT 5V ON
PORTA B4
CAM 3.2V IC601
D601
VI 3.2V VIDEO AMP

D 3.2V L602

A 3.2V, AU 3.0V, VI 3.2V, D 1.8V, D 1.2V

DSC-H5_L2
3-3
 3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-150 BOARD (2/2) L303 HDVDD

L302 TG 3V (2/8) CD-621 CD-617 BOARD
CAM 3.2V FB308 DRVDD
CP301 FLEXIBLE
D 3.2V
(2/8)
L304 FE 3V BOARD
A 3.2V TCVDD

CAM 2.9V ST 5V 4 IC301 RGVDD

S/H
A/D CONV.
IC001
3 TIMING GENERATOR
1 BUFFER
3.3V REG

CAM 15V FB302 FB301 L301 CAM 15V CD

22 22
IC002
CAM -7.5V CAM -7.5V CD
18 18 CCD IMAGER
CN301 CN001

D 3.2V D 3.2V

(1/8) 21
FC RST VCC FOCUS LENS UNIT
RESET
A 3.2V SENSOR
IC401
M 5V
IRIS DRIVE
SHUTTER DRIVE
ZM RST VCC ZOOM
FOCUS MOTOR DRIVE 27 RESET
ZOOM MOTOR DRIVE 28 SENSOR
PLUNGER DRIVE

ZM FG VCC ZOOM
33 DC FG
(6/8) CN401

L503 C542
D501
(RECT)
6
IC507 4
PANEL 8.5V

8.5V REG

D502 1
9 (RECT)
SW PANEL 8.5V 0N

1 ST UNREG 6 VBAT
PS
(6/8)
VOUT 2
5V
8
TO
POWER Q504 IC501 (6/8)
ST 5V
BLOCK DIAGRAM
IC506
1 EN DC/DC CONV.
(1/2) SE501, 502
M 5V ON
(PAGE 3-3) PITCH/YAW
PITCH/YAW
(6/8) SENSOR AMP
SENSOR
CN707
CK-161 BOARD
A 3.2V
4
IC503 3
2.9V
L703
27
PDD
VSSG
5
26 6 LCD9001
2.9V REG 3.0 INCH
L705 COLOR LCD
VDD2
1 4 28 PANEL

ST 5V ST 5V
L704
VDD1
3 29
CN001

DISCHARGE

D401
D 3.2V D 3.2V
6 28 ACCESS LED

BL H 30 BL H 4 6
31 3 5
BL L 32 BL L 2 2
33 1 CN401 1 LED9001
CN702 CN402
LCD BACK LIGHT

(6/8)
89
(6/8) SW-478 SW-471
FLEXIBLE
IC505 IC504 BOARD
BOARD
D3.2V 4 1.5V
3 STEADY SHOT
1
1.5V REG CONTROL
ST 5V

PANEL 8.5V 0N
M 5V ON
(7/8)

PANEL 2.9V L701 4 IC701 3

2.5V
LCD9002
COLOR EVF
1 22 UNIT
2.5V REG
5.0V
1

ST 5V L702 LED 5V
11
CN703 EVF BACK LIGHT

DSC-H5_L2
3-4E
 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM

MS-305 BOARD
(SIDE B) CD-617 BOARD CD-617 BOARD AF-105 FLEXIBLE BOARD
(A SIDE) (B SIDE)
39 1 S001 2 1
(LENS COVER OPEN) 3
39 1
CN001
38 2
10 1

CD-621
S201 RY201
FLEXIBLE (FLASH POP UP) (PLUNGER)

IC002 BOARD 2

MS-030 FLEXIBLE 2 1

1 6
FLAT CABLE
12

39 1
CN301

CN201
6 1
1

PL-045 BOARD PL-045 BOARD

(SIDE A) (SIDE B) 4 3

MS-305 BOARD BT9001

6 1

(SIDE A) BATTERY D001

TERMINAL AF LED

LCD9002
MIC9001
MICROPHONE
SW-471 BOARD COLOR
10 1
LEVEL3 EVF LEVEL3
(SIDE B) UNIT
SY-150 BOARD SY-150 BOARD
(SIDE B) (SIDE A)
BT001
LITHIUM BATTERY
21 (SECONDARY) CN705

14
CN302 CN001 CN703 10 1
CN602 22 1 39 1
CONTROL

CN704
MEMORY STICK Duo 4 1
38
CN301 2
CONNECTOR SWITCH
BLOCK

F001

1
F002
1
CN706

F003
ST-003 FLEXIBLE

12
FLAT CABLE

12
1

CN701
CN651
SW-478 FLEXIBLE BOARD

1
14
1
2
1
33

33
32

CN702

ST-142 BOARD
CN401

2 28 (SIDE A)
32

CN707
33

33

2 38 1 29 1 14
CN401 CN601 CN501
1

1 39
2
1

1 2
FLASH UNIT

12

CN101
1
SW-471 BOARD
(SIDE A) LND004

1 29 LND006 LND005

J001 J001 LND003

A/V OUT 4
JACK SP9001 LND002 LND001
2
SPEAKER
LCD9001
3
1
ST-144 BOARD
3.0 INCH CN001
COLOR CN001 1
LCD USB 1
CONNECTOR 2
MONITOR LND101
5
14
31 1 LND103
CN001
30 2
LED9001
LND102

CK-161 FLEXIBLE BOARD JK-306 FLEXIBLE BOARD

6

CN402

BACKLIGHT
LENS BLOCK
1

C105

ST-142 BOARD
(SIDE B)
1 2

DSC-H5_L2
4-1 FRAME SCHEMATIC DIAGRAM
 4-2. SCHEMATIC DIAGRAMS

Link
CONTROL SWITCH BLOCK
CD-617 BOARD (CCD IMAGER) (MODE/JOG DIAL, FUNCTION SW)
SW-471 BOARD AF-105 FLEXIBLE BOARD
(LCD BACK LIGHT, FUNCTION SWITCH) (AF LED, LENS COVER SW)

CK-161 BOARD (LCD PANEL) JK-306 FLEXIBLE BOARD (AV/USB JACK)

ST-142 BOARD (FLASH DRIVE) CD-621 FLEXIBLE BOARD (SY-CD RELAY)

ST-144 BOARD (FLASH) SW-478 FLEXIBLE BOARD (SY-SW RELAY)

MS-305 BOARD (MEMORY STICK) MS-030 FLEXIBLE FLAT CABLE (SY-MS RELAY)

PL-045 BOARD (PLUNGER) ST-003 FLEXIBLE FLAT CABLE (SY-ST RELAY)

COMMON NOTE FOR SCHEMATIC DIAGRAMS

DSC-H5_L2
 4-2. SCHEMATIC DIAGRAMS

4-2. SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS

(In addition to this, the necessary note is printed in each block)
(For schematic diagrams) 1. Connection
• All capacitors are in µF unless otherwise noted. pF : µ Pattern box Color bar chart
Link
µF. 50 V or less are not indicated except for electrolytics
Pattern box PTB-450 For PTB-450:
and tantalums. J-6082-200-A J-6020-250-A
• Chip resistors are 1/10 W unless otherwise noted. or
kΩ=1000 Ω, MΩ=1000 kΩ. Small pattern box For PTB-1450:
• Caution when replacing chip parts. PTB-1450 J-6082-559-A
J-6082-557-A
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
L = 1 m (PTB-450)
Example C541 L452
L = 40 cm (PTB-1450)
22U 10UH
TA A 2520 Pattern box
Front of the lens

Kinds of capacitor L Camera

Temperature characteristics
External dimensions (mm)

• Constants of resistors, capacitors, ICs and etc with XX

indicate that they are not used. 2. Adjust the distance so that the output waveform of
In such cases, the unused circuits may be indicated. Fig. a and the Fig. b can be obtain.
• Parts with * differ according to the model/destination.
H
Refer to the mount table for each function.
Yellow

Magenta
• All variable and adjustable resistors have characteristic
White
Cyan
Green
curve B, unless otherwise noted.

Red
Blue
• Signal name
XEDIT → EDIT PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line A B A=B B A
• B: B– Line Fig. a (Video output terminal output waveform)
• J : IN/OUT direction of (+,–) B LINE.
• C: adjustment for repair.
(Measuring conditions voltage)
• Voltages are measured between the measurement Electronic beam
scanning frame
points and ground when camera shoots color bar chart
of pattern box. They are reference values. CRT picture frame
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Fig.b (Picture on monitor TV)
Precautions for Replacement of imager
• If the imager has been replaced, carry out all the When indicating parts by reference number, please
adjustments for the camera section. include the board name.
• As the imager may be damaged by static electricity from Note : Note :
its structure, handle it carefully like for the MOS IC. The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
In addition, ensure that the receiver is not covered with
0 are critical for safety. pour la sécurité.
dusts nor exposed to strong light. Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.

DSC-H5_L2
4-3
 4-2. SCHEMATIC DIAGRAMS

1 2 3 4 5 6 7 8 9 10

CD-617 BOARD
NO MARK:REC/PB MODE
CCD IMAGER R :REC MODE
A XX MARK:NO MOUNT P :PB MODE

CL002

CL001
CL003

CL006
CL008
CN001 39P

V4 39 CL007

R-6.0

R-0.7

R-0.7
R-0.7

R-0.7

R-0.7
R-0.7

R-0.7

R-0.7
R-0.7
R-7.2

R-6.0

R-5.4
R-6.0
P0
P0
P0

P0

P0
P0
P0

P0

P0
P0

P0
P0

P0
P0
V10 38

VST 37
14 13 12 11 10 9 8 7 6 5 4 3 2 1
V3B 36

V10
V9

V8

V7

V6
V5B

V5A

V4
V3B

V3A

VHLD

V2
VST

V1
V1 35

B V3A 34
V6

V2
33

32
IC002 IC002
ICX629BQF-13
CCD IMAGER
V8 31

CCD_OUT
VHLD 30
Note: IC002 is not included in this
COMPLETE of CD-617 board.

CSUB
GND
GND

GND
VDD

SUB
H1B
H2B

N.C.

H1A
H2A
V7 29

RG

VL
V5B 28
15 16 17 18 19 20 21 22 23 24 25 26 27 28
V9 27

R9.1
P0
R12.7
P0
R7.7
P0
R2.1
P0
R1.1
P0
0

R9.1
P-0.2
R9.5
P0

R-7.5
P0
R2.1
P0
R1.1
P0
C V5A

REG_GND
26

25
IC001 C005
0.1u
BUFFER 16V
REG_GND 24
TO
CD-621 R001
REG_GND 23 0
FLEXIBLE
BOARD CAM_15V_CD 22

REG_GND 21 C002
(PAGE 4-12) 0.1u C004
CCD_OUT 20 R010 0.1u
R9.1 R5.0 100K 16V
P0 ISF P0

6
REG_GND 19
IN
R12.7
D CAM_-7.5V_CD 18
VCC P0

5
REG_GND 17 GND
R9.1 R4.3
P0 P0 C003

R011 0
3

4
REG_GND 16
OUT IDRV XX
R007
REG_GND 15 150k C007
0.1u
C008

0.1u 16V B
IC001 R009 16V
RG 14 XX C009
CXA3691EN-T9

C006
XX B
0.1u
REG_GND 13

H1A 12

REG_GND 11

E H1B
REG_GND
10
9
Q001
H2B 8 DTC144EMT2L R003
VSUB 270k
REG_GND 7
R004 C001
H2A 6 1 R8.8 1M XX
2 P0
REG_GND 5
R002 0
RAMDOM_TRIGGER 4 0
3
REG_GND 3

F CSUB

VSUB
2

DSC-H5_L2
4-5 CD-617
 1 2 3 4 5 6 7 8 9 10

SW-471 BOARD
LCD BACK LIGHT, FUNCTION SWITCH
A XX MARK:NO MOUNT

S407 S409
RB402
ZOOM T ZOOM W
CN401 33P 2200x4

1
XACCESS_LED 33
1 NO 2 1 NO 2
REG_GND 32 D401
SML-310LTT86 4 3 4 3
REG_GND 31
(ACCESS)
NC 30 5 6 5 6
B REG_GND 29 R401
330
D_3.2V 28
KEY_AD1 27
KEY_AD0 26
REG_GND 25
NC 24 S404
UP
NC 23
1 2
NC 22
C NC 21
S410
R405
5600

1
MENU
3 4 1005
TO NC 20 1 2
SW-478
FLEXIBLE NC 19
BOARD RB401
REG_GND 18 2200x4 3 4
(PAGE 4-12) REG_GND 17 D402
MAZW068H0LS0
NC 16
REG_GND 15
REG_GND 14
D NC 13
S406
LEFT
R403
5600
S408 R404
1 2 1 2 1 2 DISP
NC 12 S405 27k
LND401 D403 SET 1 2
REG_GND 11
STATIC_GND MA2S111-(K8).SO
3 4 3 4 3 4
NC 10
S401 3 4
NC 9 R402 RIGHT
REG_GND 8 27k

NC 7
NC 6 CN402 6P
E NC 5 6 BL_H
LED9001

BL_H 4 5 BL_H 1 2
S403
BL_H 3 4 NC S402
DUST DOWN
BL_L 2 3 NC 3 4
1 2
BL_L 1 2 BL_L
LCD
1 BL_L BACK LIGHT
3 4

DSC-H5_L2
4-6 SW-471
 1 2 3 4 5 6

CK-161 FLEXIBLE BOARD

LCD PANEL
A XX MARK:NO MOUNT
LCD9001
29P CN001 31 P (LCD UNIT)
LND001
GND 1 31 GND
LND002
GND 2 30 GND
LND003
VCC1 3 29 VCC1
LND004
VCC2 4 28 VCC2
LND005
4.2VADJ 5 27 4.2VADJ
LND006
B VBRT 6
LND007
26 VBRT
COMAC 7 25 COMAC
LND008
COMDC(H) 8 24 COMDC(H)
LND009
COMDC(L) 9 23 COMDC(L)
LND010
VD 10 22 VD
LND011
HD 11 21 HD
LND012
DCK 12 20 DCK
TO LND013 3.0 INCH
SY-150 D7 13 19 D7 COLOR
LND014 LCD PANEL
C BOARD(7/8)
CN707 D6 14
LND015
18 D6
D5 15 17 D5
(PAGE 4-20 LND016
D4 16 16 D4
of LEVEL 3) LND017
D3 17 15 D3
LND018
D2 18 14 D2
LND019
D1 19 13 D1
LND020
D0 20 12 D0
LND021
XCS 21 11 XCS
LND022
D SI 22
LND023
10 SI
SCLK 23 9 SCLK
LND024
RESET 24 8 RESET
LND025
POFF 25 7 POFF
LND026
VSSG 26 6 VSSG
LND027
PVDD 27 5 PVDD
LND028
GND 28 4 GND
LND029
COM 29 3 COM

E 2 N.C.

1 N.C.

DSC-H5_L2
4-7 CK-161
 • Refer to page 4-3 for mark 0.

1 2 3 4 5 6 7 8 9 10

ST-142 BOARD NO MARK:REC/PB MODE

R :REC MODE
FLASH DRIVE P :PB MODE T101
CONVERTER
A XX MARK:NO MOUNT TRANSFORMER

L101 5 3
CN101 12P 4.7uH
ST_UNREG 1 2 D102
C101 C102 C106
22u 22u 22u CRF02(TE85R)
ST_UNREG 2 LND101
6.3V 6.3V 6.3V 1 4 1 XE_H
ST_UNREG 3 CL101
TO STRB_ON 4
ST-003 FLEXIBLE
FLAT CABLE STRB_CHG_CONT 5
B (PAGE 4-13) XSTRB_FULL 6
STRB_CHG 7
C105 Note: C105 is not included in this
ST_5V 8
320u COMPLETE of ST-142 board.
REG_GND 9 330V

REG_GND 10
REG_GND 11
REG_GND 12
TO
ST-144
C R2.4/P2.6 BOARD
17 16 15 14 13 (PAGE 4-9)

HGND

VBATT
N.C

N.C

N.C
R2.4/P2.6 PGND
IC101

10 11 12
1
SW
R2.4/P2.6 PGND

2
5.0 SW 0 LND102
HIGH VOLTAGE CHARGE, CHG
D

3
VCC 2 REG_GND
0 IGBT DRIVE 3.2
XFULL

9
F_ON IC101
TPS65552RGTR

I_PEAK

G_IGBT
C103
D101 R102

N.C

N.C
1u
MAZS068008SO XX B Q101
GT8G133 (T2LSONY.Q)
5 6 7 8 FLASH DRIVE
283 LND103
3 XE_L

0
1 5

E 2 6

0 3 7

R103 4 8
4.7M
C104
XX R104
33

DSC-H5_L2
4-8 ST-142
 • Refer to page 4-3 for mark 0.

1 2 3 4 5 6 1 2 3 4

ST-144 BOARD PL-045 BOARD

FLASH Note: RY201 is not included in this
PLUNGER
A XX MARK:NO MOUNT A COMPLETE of PL-045 board.
XX MARK:NO MOUNT

CN201 6P D202 D203

LND005 1SS355TE-17 MAZW068H0LS0
LND001 REG_GND 1
XE_H 1 XE_+ 2
TO REG_GND 2 C201 1
RY201
AF-105 1u
STRB_PLUNGER 3 (PLUNGER)
R001 FLEXIBLE 3
1M C002 BOARD STRB_PLUNGER 4
0.047u L001
B 250V TRIGGER COIL
1 3
LND004 B (PAGE 4-11) REG_GND 5
XSTRB_POPUP 6
TRIGGER FLASH
S201
TO UNIT
ST-142 C003 (FLASH POP UP)
BOARD 0.01u
250V 2
(PAGE 4-8)
LND006
LND002
XE_L 2 XE_-
D001
RR255L-400TE25
C R002
100k

LND003
REG_GND 3

1 2 3 4 5 6

MS-305 BOARD
MEMORY STICK
A XX MARK:NO MOUNT

CN301 12P 10P

REG_GND 1 1 REG_GND
R303 82 FB305 0
MS_BS 2 2 MS_BS
FB301 0uH
MS_D1 3 3 MS_D1
FB302 0uH CN302
TO MS_D0 4 4 MS_D0
B MS-030
FLEXIBLE
MS_D2 5
R302 1k
FB303 0uH
5 MS_D2
MEMORY
STICK Duo
CONNECTOR
FLAT CABLE XMS_IN 6 6 XMS_IN
(PAGE 4-13) FB304 0uH
MS_D3 7 7 MS_D3
R304 82 FB306 0
MS_SCLK 8 8 MS_SCLK
REG_GND 9 9 MS_VCC
C301 C302
MS_VCC 10 0.1u 10 REG_GND
22u
6.3V B
REG_GND 11
REG_GND 12
C
LND302 STATIC_GND

DSC-H5_L2
4-9 ST-144/MS-305/PL-045
 1 2 3 4 5 6 7 8

CONTROL SWITCH BLOCK

MODE/JOG DIAL, FUNCTION SW R109 R111 R112
A XX MARK:NO MOUNT 2k 2k 2k
S106
S107

(MODE DIAL) STEADY SHOT

S101 S102 FINDER
R104 6 13 R115
2k 7 2 1 2 1
FOCUS BRK 2k

2 1 2 1 5 12
R105 R116 4 3 4 3
2k 2k
4 11
4 3 4 3
R106 R117
2k 3 10 2k

B R101
4900 R107
2k
2 1 8 9 R118
2k

R110 R114
2k 2k
R108
10k

R103 2200

C R102
S103

9300 SHUTTER
S105
3 1 S104 JOG DIAL

4 2 POWER
1 3

7
1

3
4

6
2 4

D
S108

PLAY
1 3
D102
POWER
2 4

E CONTROL SWITCH BLOCK is replaced as a block.

So that this PRINTED WIRING BOARD is omitted.
LND101
LND102
LND103

LND104

LND105
LND106

LND107
LND108
LND109
LND110
LND111

LND112
LND113
LND114
XSHUTTER_SW

XAE_LOCK_SW

F
MODE_DIAL1

MODE_DIAL0
XPWR_LED
KEY_BONO
XPLAY_SW

XPWR_ON

REG_GND

KEY_AD2
D_3.2V

A_3.2V
JOG_B
JOG_A
14P

10
11
12
13

14
1
2

3
4
5
6
7

8
9

TO SY-150 BOARD(7/8) CN704

(PAGE 4-20
G of LEVEL 3)

DSC-H5_L2
4-10 MODE DIAL
 1 2 3 4 5 6

AF-105 FLEXIBLE BOARD Note: D001 is not included in this

AF LED,LENS COVER SW COMPLETE of AF-105 board.
A D001
DOR5073
XX MARK:NO MOUNT
S001 (AF LED)
(LENS COVER OPEN) 1 6
10P
LND001 2 5
1 XLENS_COVER_SENSE
LND002 3 4
2 REG_GND
LND003
3 D_3.2V
LND004
TO 4 XAF_LED 6P
SY-150 LND005 LND011
B BOARD
(7/8)
5
6
XSTRB_POPUP
REG_GND
LND006 LND012
XSTRB_POPUP
REG_GND
1
2
TO
CN705 PL-045
LND007 LND013
BOARD
(PAGE 4-20 7 STRB_PLUNGER
LND008 LND014
STRB_PLUNGER 3
CN201
of LEVEL 3) 8 STRB_PLUNGER STRB_PLUNGER 4
LND009 LND015 (PAGE 4-9)
9 REG_GND REG_GND 5
LND010 LND016
10 REG_GND REG_GND 6

1 2 3 4 5 6

JK-306 FLEXIBLE BOARD

AV/USB JACK
A XX MARK:NO MOUNT

14P 3
LND001 1 J001
XAV_JACK_IN 1
LND002 2 A/V OUT
V_LINE_OUT 2 4
LND003
AU_LINE_OUT 3
LND004
GND 4
LND005
TO NC 5
B SY-150 BOARD
(5/8)
VCC 6
LND006
CN001 5P
LND007
CN651 GND 7 5 GND
LND008
(PAGE 4-18 D- 8
LND009
4 ID

of LEVEL 3) D+ 9 3 D+
LND010
GND 10 2 D- (USB)
LND011
GND 11 1 VCC
LND012
NC 12
LND013
STATIC_GND 13 LND015
C STATIC_GND 14
LND014
STATIC_GND

DSC-H5_L2
4-11 AF-105/JK-306
 1 2 3 4 5 1 2 3 4 5

CD-621 FLEXIBLE BOARD SW-478 FLEXIBLE BOARD

SY-CD RELAY SY-SW RELAY
A XX MARK:NO MOUNT A XX MARK:NO MOUNT

33P 33P
39P 39P
BL_L 33 1 BL_L
V4 39 39 V4
BL_L 32 2 BL_L
V10 38 38 V10
BL_H 31 3 BL_H
VST 37 37 VST
BL_H 30 4 BL_H
V3B 36 36 V3B
NC 29 5 NC
B V1 35 35 V1
B NC 28 6 NC
V3A 34 34 V3A
NC 27 7 NC
V6 33 33 V6
REG_GND 26 8 REG_GND
V2 32 32 V2
NC 25 9 NC
V8 31 31 V8
NC 24 10 NC
VHLD 30 30 VHLD
REG_GND 23 11 REG_GND
V7 29 29 V7
NC 22 12 NC
V5B 28 28 V5B
NC 21 13 NC
C V9 27 27 V9
C TO
REG_GND 20 14 REG_GND
TO
V5A 26 26 V5A
SY-150 REG_GND 19 15 REG_GND SW-471
REG_GND 25 25 REG_GND BOARD(7/8) BOARD
CN702 NC 18 16 NC CN401
REG_GND 24 24 REG_GND
(PAGE 4-20 REG_GND 17 17 REG_GND (PAGE 4-6)
TO REG_GND 23 23 REG_GND TO of LEVEL 3) REG_GND 16 18 REG_GND
SY-150 CAM_15V_CD 22 22 CAM_15V_CD CD-617
BOARD(2/8) BOARD NC 15 19 NC
CN301 REG_GND 21 21 REG_GND CN001
NC 14 20 NC
(PAGE 4-15 CCD_OUT 20 20 CCD_OUT (PAGE 4-5) NC 13 21 NC
D of LEVEL 3) REG_GND 19 19 REG_GND
D NC 12 22 NC
CAM_-7.5V_CD 18 18 CAM_-7.5V_CD
NC 11 23 NC
REG_GND 17 17 REG_GND
NC 10 24 NC
REG_GND 16 16 REG_GND
REG_GND 9 25 REG_GND
REG_GND 15 15 REG_GND
KEY_AD0 8 26 KEY_AD0
RG 14 14 RG
KEY_AD1 7 27 KEY_AD1
REG_GND 13 13 REG_GND
D_3.2V 6 28 D_3.2V
H1A 12 12 H1A
REG_GND 5 29 REG_GND
E REG_GND 11 11 REG_GND
E NC 4 30 NC
H1B 10 10 H1B
REG_GND 3 31 REG_GND
REG_GND 9 9 REG_GND
REG_GND 2 32 REG_GND
H2B 8 8 H2B
XACCESS_LED 1 33 XACCESS_LED
REG_GND 7 7 REG_GND

H2A 6 6 H2A

REG_GND 5 5 REG_GND

RANDOM_TRIGGER 4 4 RANDOM_TRIGGER

F REG_GND

CSUB
3

2
3

2
REG_GND

CSUB

VSUB 1 1 VSUB

DSC-H5_L2
4-12 CD-621/SW-478
 1 2 3 4 5 1 2 3 4 5

MS-030 FLEXIBLE FLAT CABLE ST-003 FLEXIBLE FLAT CABLE

SY-MS RELAY SY-ST RELAY
A XX MARK:NO MOUNT A XX MARK:NO MOUNT

12P 12P 12P 12P

REG_GND 1 1 REG_GND REG_GND 12 12 REG_GND
MS_BS 2 2 MS_BS REG_GND 11 11 REG_GND
MS_D1 3 3 MS_D1 REG_GND 10 10 REG_GND
MS_D0 4 4 MS_D0 REG_GND 9 9 REG_GND
TO MS_D2 5 5 MS_D2 TO TO ST_5V 8 8 ST_5V TO
B SY-150
BOARD(7/8) XMS_IN 6 6 XMS_IN
MS-305
BOARD B SY-150
BOARD(7/8) STRB_CHG 7 7 STRB_CHG
ST-142
BOARD
CN706 CN301 CN701 CN101
MS_D3 7 7 MS_D3 XSTRB_FULL 6 6 XSTRB_FULL
(PAGE 4-20 (PAGE 4-9) (PAGE 4-20 (PAGE 4-8)
MS_SCLK 8 8 MS_SCLK STRB_CHG_CONT 5 5 STRB_CHG_CONT
of LEVEL 3) of LEVEL 3)
REG_GND 9 9 REG_GND STRB_ON 4 4 STRB_ON
MS_VCC 10 10 MS_VCC ST_UNREG 3 3 ST_UNREG
REG_GND 11 11 REG_GND ST_UNREG 2 2 ST_UNREG
REG_GND 12 12 REG_GND ST_UNREG 1 1 ST_UNREG

C MS-030 FLEXIBLE FLAT CABLE is replaced as a block. C ST-003 FLEXIBLE FLAT CABLE is replaced as a block.
So that this PRINTED WIRING BOARD is omitted.
So that this PRINTED WIRING BOARD is omitted.

Schematic diagram of the SY-150 board and CH-199

board are not shown.
Pages from 4-14 to 4-22 are not shown.

DSC-H5_L2
4-13 MS-030/ST-003
 4-3. PRINTED WIRING BOARDS

Link

CD-617 BOARD AF-105 FLEXIBLE BOARD

SW-471 BOARD JK-306 FLEXIBLE BOARD

ST-142 BOARD CD-621 FLEXIBLE BOARD

ST-144 BOARD SW-478 FLEXIBLE BOARD

MS-305 BOARD CK-161 FLEXIBLE BOARD

PL-045 BOARD

COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION

DSC-H5_L2
 4-3. PRINTED WIRING BOARDS

4-3. PRINTED WIRING BOARDS

THIS NOTE IS COMMON FOR WIRING BOARDS
(In addition to this, the necessary note is printed in each block)

(For printed wiring boards)

• : Uses unleaded solder. • Chip parts.
• : Pattern from the side which enables seeing. Transistor Diode
C 6 5 4 4 5 6 5 4 4 5 3 3 3 1 23
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• There are a few cases that the part printed on diagram B E 1 2 3 3 2 1 1 2 3 3 2 1 2 1 2 1 2 1 6 54
isn’t mounted in this model. 1 2 2 1 3 4 1 2 3 4 4 3 3 4
• C: panel designation

5 4 3 3 4 5 2 1 4 3 2 1 1 2 2 1
6 4 3
5 4

1 3 1 1 2
3

DSC-H5_L2
4-23
 4-3. PRINTED WIRING BOARDS
CD-617 (4 layers), SW-471 (4 layers) • : Uses unleaded solder.

CD-617 BOARD(SIDE A) CD-617 BOARD(SIDE B)

Note:IC002 is not included in A
A this COMPLETE of CD-617 board

28 15

C003

C005

R010
C004

C002

R009
R011

6
C008

1
IC002
R007

4
IC001
C009

C007
B

R001
1 14 B

R004
1-869-215-

R003

C001
R002

CL003
CL001
1 C006
11
2 38 CL007

CL002
1
CN001 2 3
CL008
39 Q001
11 CL006
1-869-215-

1 2 3 1 2 3

SW-471 BOARD(SIDE A) SW-471 BOARD(SIDE B)

A A
4 2 4 2
R404

1 3
2
S401
R405

5 3 1 3 1
4 RIGHT K A
S408 S410 R401 RB401
1-869
-214-

2 4
1
DISP D401
D403 D402

2
MENU

1
6
SW-471

S407 S405 SET (ACCESS) B

LND401

2 8

2 3
B 1

8
3 ZOOM T RB402
3

4
3

1
S403
7
6 S404 R402 R403
1 DOWN
UP
1

2
1

CN402
1

S409 1 3 4 2
2 32
S406 S402
>EP GW<

ZOOM W
1
CN401 33
LEFT DUST
C C
3

4
6

2 4 3 1
1-869-214-
1-869-214- 11

1 2 3 4 5 6 6 5 4 3 2 1

DSC-H5_L2
4-25 CD-617/SW-471
 ST-142 (2 layers), ST-144 (1 layer), MS-305 (4 layers) • : Uses unleaded solder.

ST-142 BOARD(SIDE A) ST-142 BOARD(SIDE B)

>EP GW< ST142-
L101

2
3
C102
C101
A T101 A

5
LND102
LND101

LND103

4
1
C103
CL101
C106

R103
1
R104 5 4 16
Q101

A K
5

1 4
17
8 13 R102
IC101 D102
8

9 12

D101 C104

C105
B 1 12 B
ST-142 CN101

2
1-869-218- 1-869-218- 11

1-869-218- 11

1 2 3 4 4 3 2 1

LND302
ST-144 BOARD MS-305 BOARD(SIDE A) MS-305 BOARD(SIDE B)

D001

11
LND001 CN301
LND002 R001
ST144

1
>PI<

1-869-216-
MS-305 >EP
C003 12

R304

R303
C002

LND003
FB305
R002 FB301
FB302 CN302 + P
FB303 C301
R302 MEMORY STICK Duo
FB304 CONNECTOR
FB306

GW<
LND006 LND005
2 1-869-216-
C302

L001 3 1-869-225-
10

1 LND004 11 11
12

1-869-216- 11

DSC-H5_L2
4-26 ST-142/ST-144/MS-305
 PL-045 (2 layers), AF-105 FLEXIBLE (1 layer), JK-306 FLEXIBLE (1 layer) • : Uses unleaded solder.

PL-045 BOARD
PL-045 BOARD
(SIDE B)
(SIDE A) 1 6

CN201

D202
>EP GW<

D203
C201

2
1
3
S201
(FLASH POP UP)
1 2
1

RY201
2

PL045
(PLUNGER) 1-869-217- 11
1-869-217- 11

AF-105 FLEXIBLE BOARD JK-306 FLEXIBLE BOARD

1
LND011
LND012
LND013
LND014
LND015
LND016 6

J001 A/V OUT

>PI<

1 CN001
D001
10 1
AF LED LND010
2
K

LND009
LND008 S001
(USB)
6 4 LND007
LND006
LND005
(LENS COVER OPEN) 5
LND004
LND003
LND002
2
14 FX JK-306-
1 3
1
1 3 1-869-224-
A

11
AF-105 1-869-223- >PI< 1-869-223- 11

DSC-H5_L2
4-27 PL-045/AF-105/JK-306
 CD-621 FLEXIBLE (2 layers), SW-478 FLEXIBLE (1 layer), CK-161 FLEXIBLE (2 layer) • : Uses unleaded solder.

CD-621 FLEXIBLE BOARD

1
1

1-869-222- 39
39
11

SW-478 FLEXIBLE BOARD CK-161 FLEXIBLE BOARD

33 1

2 30
CN001
1 31
>PI<
SW-478-
FX

1-869-226- 11
LND029
LND028
LND027
LND026
LND025
LND024
LND023
LND022
LND021
LND020
LND019
LND018
LND017
LND016
LND015
LND014
LND013
LND012
LND011
LND010
LND009
LND008
LND007
LND006
LND005
LND004
LND003
LND002
LND001
SY

29 1

1-869-227-
Printed wiring board of the SY-150 board and CH-199
11
board are not shown.
1 33
Pages from 4-29 to 4-31 are not shown.

DSC-H5_L2
4-28 CD-621/SW-478/CK-161
 4-3. PRINTED WIRING BOARDS

4-4. MOUNTED PARTS LOCATION no mark : side A

* mark : side B
CD-617 BOARD SW-471 BOARD ST-142 BOARD

* C001 B-2 * CN401 C-5 C101 A-2

* C002 B-1 CN402 B-2 C102 A-2
* C003 B-1 C103 A-2
* C004 B-1 D401 B-6 C104 B-2
* C005 B-1 * D402 B-6 * C105 B-3
* C006 B-2 * D403 B-5 C106 B-3
* C007 B-1
* C008 B-2 * LND401 B-6 CL101 A-2
* C009 B-2
* R401 B-5 CN101 B-3
* CL001 B-3 * R402 B-5
* CL002 B-3 * R403 B-5 D101 B-2
* CL003 B-3 R404 A-2 D102 B-3
* CL006 B-3 R405 B-2
* CL007 B-3 IC101 B-3
* CL008 B-3 * RB401 B-5
RB402 B-2 L101 A-1
* CN001 B-1
S401 A-4 LND101 A-1
* IC001 B-1 S402 C-5 LND102 A-2
IC002 B-2 S403 B-5 LND103 A-1
S404 B-3
* Q001 B-2 S405 B-4 Q101 B-1
S406 C-4
* R001 B-2 S407 B-1 R102 B-3
* R002 B-2 S408 B-2 R103 B-2
* R003 B-2 S409 C-1 R104 B-2
* R004 B-2 S410 B-3
* R007 B-2 T101 A-3
* R009 B-2
* R010 B-2
* R011 B-1

Mounted parts location of the SY-150 board is not shown.

Page 4-33 is not shown.

DSC-H5_L2
4-32E CD-617/SW-471/ST-142
 NOTE

5. REPAIR PARTS LIST

NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.

Link EXPLODED VIEWS

J
I
G
F B D

OVERALL SECTION LCD SECTION MAIN SECTION LENS SECTION

H
C
A E

CABINET (FRONT) SECTION ST SECTION

Link ELECTRICAL PARTS LIST ACCESSORIES

AF-105 FLEXIBLE BOARD A MS-305 BOARD B ST-144 BOARD C

CD-617 BOARD D PL-045 BOARD E SW-471 BOARD F

CK-161 FLEXIBLE BOARD G ST-142 BOARD H SY-150 BOARD I

JK-306 FLEXIBLE BOARD J

DSC-H5_L2
 5. REPAIR PARTS LIST

5. REPAIR PARTS LIST

NOTE:
• -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number,
the original one. please include the board name.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or
• The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety.
supplied. Replace only with part number specified.
• Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque
the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
• CAPACITORS:
le numéro spécifié.
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...

Language that can be selected about SY-150 board

Norwegian
Traditional

Hungarian
Japanese

Simplified

Swedish
Portugal

Chinese

Chinese
Spanish

Russian
German

Persian
English

Korean

Finnish
French

Danish
Arabic

Czech
Polish
Italian

Dutch
Area

Thai

GP1 J z
US
CND
GP2 AUS z z z z z z
Vietnam
AEP
GP3 z z z z z z z z z z z z z z z
UK
E
JE
HK
GP4 z z z z z z z z z
CH
KR
BR

• Abbreviation
J : Japanese model
CND : Canadian model
AUS : Australian model
JE : Tourist model
HK : Hong Kong model
CH : Chinese model
KR : Korea model
BR : Brazilian model

DSC-H5_L2
5-1
 5. REPAIR PARTS LIST

5-1. EXPLODED VIEWS

5-1-1. OVERALL SECTION
ns : not supplied

3
2
-
SW
1
47

3
4
8

1 ns

LCD section
(See page 5-4)
5

3
7
6

Ref. No. Part No. Description Ref. No. Part No. Description
1 2-673-346-01 PLATE, ORNAMENTAL 5 2-673-247-01 LID, DC (SILVER)
2 2-673-327-11 CABINET (UPPER) (SILVER) 5 2-673-247-11 LID, DC (BLACK)
2 2-673-327-21 CABINET (UPPER) (BLACK) 6 2-673-303-01 LID, JK (SILVER)
3 2-630-005-31 SCREW (M2), NEW TRUSTER, P2 (BLACK) 6 2-673-303-11 LID, JK (BLACK)
3 2-655-582-11 SCREW 0+P2 M2 NEWTRU-STAR (SILVER) 7 2-673-345-01 WINDOW (420), LCD

4 X-2108-909-1 CABINET (REAR) ASSY (420) (SILVER) * 8 2-685-484-01 CUSHION (REAR)

4 X-2109-111-1 CABINET (REAR) ASSY (420D) (BLACK)

DSC-H5_L2
5-3
 5. REPAIR PARTS LIST

5-1-2. LCD SECTION

Cabinet (front) section

(See page 5-7)

55

51
56

52
0
-15
SY 52

Lens section 53
(See page 5-6)
58
60
Main section
54 57
(See page 5-5)

LED9001

59 LCD9001

Ref. No. Part No. Description Ref. No. Part No. Description
51 2-666-551-21 SCREW, TAPPING, P2 * 57 2-673-342-01 FRAME (420), LCD
52 3-078-890-01 SCREW, TAPPING * 58 2-673-344-01 HOLDER (R), LCD
* 53 2-694-714-01 TAPE CD RETAINER (420) * 59 2-673-343-01 HOLDER (L), LCD
* 54 2-673-339-03 LABEL, FUSE REPLACEMENT CAUTION 60 2-666-551-21 SCREW, TAPPING, P2
55 A-1176-922-A SW-471 BOARD, COMPLETE LCD9001 8-753-256-97 ACX541AKA-1

* 56 2-678-099-01 SHEET, SW MUFFLE LED9001 1-479-403-11 BLOCK, LIGHT GUIDE PLATE (3.0)

DSC-H5_L2
5-4
 5. REPAIR PARTS LIST

5-1-3. MAIN SECTION

ns : not supplied

111
LCD9002

113
112 BT9001
102

MS
-30
5 114

110 A

106

BT001

ns
A
109
115
107

-150
105
116 SY
108 102

103
SP9001

101 102 104

ns

: BT001 (Lithium battery) SY-150 board

on the mount position. (See page 4-29)

Ref. No. Part No. Description Ref. No. Part No. Description
* 101 2-684-446-01 SPACER, SP * 110 2-677-004-01 SHEET (INR), RADIATION
102 3-080-204-11 SCREW, TAPPING, P2 * 111 2-673-337-01 RETAINER, MODULE
* 103 2-672-564-01 SHEET (JK), RADIATION 112 X-2108-913-1 ASSY, VF
104 A-1176-978-A CK-161 FLEXIBLE BOARD, COMPLETE 113 A-1176-924-A MS-305 BOARD, COMPLETE
105 A-1176-915-A JK-306 FLEXIBLE BOARD, COMPLETE 114 1-831-557-11 FLEXIBLE FLAT CABLE (MS-030)

106 A-1176-925-A SY-150 BOARD, COMPLETE (SERVICE) (GP1) * 115 2-694-712-01 USB PROTECTION SHEET
106 A-1176-926-A SY-150 BOARD, COMPLETE (SERVICE) (GP2) * 116 2-694-713-01 USB GASKET
106 A-1176-927-A SY-150 BOARD, COMPLETE (SERVICE) (GP3) 0 BT001 1-756-539-21 BATTERY, LITHIUM SECONDARY
106 A-1176-928-A SY-150 BOARD, COMPLETE (SERVICE) (GP4) * BT9001 1-780-338-11 TERMINAL BOARD, BATTERY (SILVER)
107 1-869-227-11 SW-478 FLEXIBLE BOARD * BT9001 1-780-338-21 TERMINAL BOARD, BATTERY (BLACK)

* 108 2-673-306-01 PLATE, JK GROUND LCD9002 1-802-033-11 LCD MODULE

109 X-2108-910-1 HOLDER ASSY, BATTERY (SILVER) SP9001 1-826-403-21 LOUDSPEAKER (1.0CM)
109 X-2109-112-1 HOLDER (420D), BATTERY (BLACK)
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

DSC-H5_L2 • Refer to page 5-1 for mark 0.

5-5
 5. REPAIR PARTS LIST

5-1-4. LENS SECTION

ns : not supplied

161

154

157 158

151
153
17
155 -6
156 CD

IC002
152
159
160

ns

ns 160

Ref. No. Part No. Description Ref. No. Part No. Description
151 A-1177-128-A SERVICE, OPTICS UNIT (B191A) (SERVICE) 158 1-869-222-11 CD-621 FLEXIBLE BOARD
* 152 2-672-563-01 SHEET (LNS), RADIATION 159 A-1176-923-A CD-617 BOARD, COMPLETE
153 2-592-693-01 PLATE (T), LIGHT INTERCEPTION (IC002 is not included in this COMPLETE board.)
* 154 2-672-565-01 SHEET (TB), RADIATION 160 2-666-551-21 SCREW, TAPPING, P2
155 1-788-338-11 OPTICAL FILTER BLOCK * 161 2-689-504-01 SHEET (LNS 2), RADIATION
IC002 A-1176-035-A CCD BLOCK ASSY (CCD IMAGER)
156 2-592-605-01 RUBBER (TM), SEAL (IC002 is not included in this COMPLETE board
* 157 2-672-562-01 SHEET (CD), RADIATION of CD-617.)

Be sure to read “Precautions upon replacing CCD imager”

on page 4-3 when changing the CCD imager.

DSC-H5_L2
5-6
 5. REPAIR PARTS LIST

5-1-5. CABINET (FRONT) SECTION

ns : not supplied

ST section
208 (See page 5-8)

209

212
207

210
211
219
213

202

206

205 214
MIC9001

202
215
216
ns 202
203
218 202
217 202
204 202 201

Ref. No. Part No. Description Ref. No. Part No. Description
201 X-2108-907-1 CABINET (FRONT) ASSY (420) (SILVER) * 210 2-673-305-01 PLATE, GRIP GROUND
201 X-2109-110-1 CABINET (FRONT) ASSY (420D) (BLACK) * 211 2-673-302-01 HOLDER, AF
202 3-080-204-11 SCREW, TAPPING, P2 212 1-831-558-11 FLEXIBLE FLAT CABLE (ST-003)
203 2-673-230-01 SCREW, TRIPOD 213 1-479-699-21 SWITCH BLOCK, CONTROL
* 204 2-673-328-01 SHEET METAL (R), STRAP * 214 2-673-335-01 CUSHION, MICROPHONE

205 2-673-324-11 RING, ORNAMENTAL * 215 2-678-097-01 CUSHION (B), MICROPHONE

206 2-673-323-11 RING, LENS * 216 2-673-334-01 HOLDER, MICROPHONE
207 2-673-325-11 GRIP (SILVER) 217 A-1176-913-A AF-105 FLEXIBLE BOARD, COMPLETE
207 2-673-325-21 GRIP (BLACK) * 218 2-689-505-01 SHEET (TRIPOD), RADIATION
208 X-2108-326-1 RELEASE ASSY (420) 219 2-695-940-01 SPACER, RELEASE

209 2-673-301-11 BUTTON, FB MIC9001 1-542-618-21 MICROPHONE

DSC-H5_L2
5-7
 5. REPAIR PARTS LIST

5-1-6. ST SECTION
ns : not supplied

255 257
258
254
256

264

C105

251
Blue

263
RY201 Red 261
White
260
262
259
253

252

251
PRECAUTION DURING SOLENOID PLUNGER INSTALLATION

7
6

5
4
3
2

1 Close the ST cover. 3 Two claws 5 PL-045 board

2 Plunger solenoid 4 Solenoid retainer 6 Apply the soldering in two points.

7 Tapping screw (M1.7x4)

Ref. No. Part No. Description Ref. No. Part No. Description
251 3-080-204-11 SCREW, TAPPING, P2 258 2-673-326-11 COVER, ST (BLACK)
252 A-1176-908-A PL-045 BOARD, COMPLETE 259 1-964-411-11 HARNESS (HA-004) (Red)
253 2-629-818-01 RETAINER, SOLENOID 260 1-964-411-21 HARNESS (HA-004) (White)
254 X-2108-912-1 BASE ASSY, ST 261 1-964-411-31 HARNESS (HA-004) (Blue)
0 255 1-479-553-11 FLASH UNIT * 262 2-678-098-01 SHEET, ST ELECTROSTATIC

256 A-1176-914-A ST-144 BOARD, COMPLETE 263 A-1176-909-A ST-142 BOARD, COMPLETE
257 2-673-341-01 EMBLEM (320), ST (SILVER) * 264 2-678-099-01 SHEET, SW MUFFLE
257 2-673-341-11 EMBLEM (320), ST (BLACK) 0 C105 1-112-763-11 CAP, ELECT 320uF 330V
258 2-673-326-01 COVER, ST (SILVER) RY201 1-455-038-11 SOLENOID, PLUNGER

DSC-H5_L2 • Refer to page 5-1 for mark 0.

5-8
 5. REPAIR PARTS LIST

Checking supplied accessories.

Make sure that the following accessories are supplied with your camcorder.

0 Ni-MH battery charger BC-CS2A/CS2B (1) HR6 (size AA) Nickel-Metal Adaptor ring (1)
(US,CND,JE,J model) Hydride batteries (2) 2-629-861-01
1-479-378-11 (not supplied)
0 Ni-MH battery charger BC-CS2A/CS2B (1)
(AEP,UK,E,AUS,HK model)
1-479-378-21
0 Ni-MH battery charger BC-CS2A/CS2B (1)
(KR,CH model)
1-479-378-31
Battery case (1) Lens cap (1)
3-074-757-01 X-2055-960-1

0 Power cord (Mains lead) (1) Lens cap strap (1)

(US,CND model) 3-979-194-31
1-790-107-51
USB cable (1)
0 Power cord (Mains lead) (1)
1-829-868-41
(AEP,E model)
1-824-910-31
0 Power cord (Mains lead) (1) CD-ROM
(AUS model) (Cyber-shot application software) (1)
1-827-945-41 AV cable (1) (Except BR model)
0 Power cord (Mains lead) (1) 1-824-519-11 2-666-673-03
(KR model)
1-823-947-51
0 Power cord (Mains lead) (1)
(UK model)
1-827-269-22
0 Power cord (Mains lead) (1) Shoulder strap (1) 2-pin conversion adaptor (1)
(HK model) 2-629-892-01 (JE model)
1-783-374-22 1-569-007-12
0 Power cord (Mains lead) (1)
(CH model)
1-782-476-41
0 Power cord (Mains lead) (1)
(JE, J model)
1-792-549-31
Lens hood (1) 2-pin conversion adaptor (1)
2-629-860-01 (E model)
1-569-008-12
Other accessories
2-673-174-01 INSTRUCTION (READ THIS FIRST) (JAPANESE)(J) 2-673-175-31 INSTRUCTION (READ THIS FIRST)
2-673-174-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (NORWEGIAN/DANISH)(AEP)
(US,CND,AEP,UK,E,AUS,HK,JE) 2-673-176-01 INSTRUCTION (USER’S GUIDE) (JAPANESE)(J)
2-673-174-21 INSTRUCTION (READ THIS FIRST) (FRENCH/ITALIAN) 2-673-176-11 INSTRUCTION (USER’S GUIDE) (ENGLISH)
(CND,AEP) (US,CND,AEP,UK,E,AUS,HK,JE)
2-673-174-31 INSTRUCTION (READ THIS FIRST) 2-673-176-21 INSTRUCTION (USER’S GUIDE) (FRENCH/ITALIAN)
(SPANISH/PORTUGUESE)(AEP,E,JE) (CND,AEP)
2-673-174-41 INSTRUCTION (READ THIS FIRST) (GERMAN/DUTCH) 2-673-176-31 INSTRUCTION (USER’S GUIDE)
(AEP) (SPANISH/PORTUGUESE)(AEP,E,JE)

2-673-174-51 INSTRUCTION (READ THIS FIRST) 2-673-176-41 INSTRUCTION (USER’S GUIDE) (GERMAN/DUTCH)(AEP)
(SIMPLIFIED CHINESE/TRADITIONAL CHINESE) 2-673-176-51 INSTRUCTION (USER’S GUIDE) (SIMPLIFIED CHINESE/
(E,HK,CH,JE) TRADITIONAL CHINESE)(E,HK,CH,JE)
2-673-174-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN)(AEP) 2-673-176-61 INSTRUCTION (USER’S GUIDE) (RUSSIAN)(AEP)
2-673-174-71 INSTRUCTION (READ THIS FIRST) (ARABIC/PERSIAN)(E) 2-673-176-71 INSTRUCTION (USER’S GUIDE) (ARABIC/PERSIAN)(E)
2-673-174-81 INSTRUCTION (READ THIS FIRST) (KOREAN)(KR,JE) 2-673-176-81 INSTRUCTION (USER’S GUIDE) (KOREAN)(KR,JE)
2-673-174-91 INSTRUCTION (READ THIS FIRST) (CZECH/POLISH)
(AEP) 2-673-176-91 INSTRUCTION (USER’S GUIDE) (POLISH/CZECH)(AEP)
2-673-177-11 INSTRUCTION (USER’S GUIDE) (HUNGARIAN/SLOVAK)
2-673-175-11 INSTRUCTION (READ THIS FIRST) (AEP)
(HUNGARIAN/SLOVAK)(AEP) 2-673-177-21 INSTRUCTION (USER’S GUIDE) (SWEDISH/FINNISH)
2-673-175-21 INSTRUCTION (READ THIS FIRST) (SWEDISH/FINNISH) (AEP)
(AEP) 2-673-177-31 INSTRUCTION (USER’S GUIDE) (NORWEGIAN/DANISH)
(AEP)

DSC-H5_L2 • Refer to page 5-1 for mark 0.

5-9
 AF-105 CD-617 CK-161 JK-306 MS-305 PL-045

5-2. ELECTRICAL PARTS LIST

Ref. No. Part No. Description Ref. No. Part No. Description
A-1176-913-A AF-105 FLEXIBLE BOARD, COMPLETE A-1176-915-A JK-306 FLEXIBLE BOARD, COMPLETE
****************************** ********************
(D001 is not included in this COMPLETE board.)
< CONNECTOR >
< DIODE >
CN001 1-794-962-11 CONNECTOR, SQUARE TYPE (USB 5P)
D001 Not supplied DIODE DOR5073 (AF LED)
(D001 is not included in this COMPLETE of < JACK >
AF-105 board.)
J001 1-793-620-41 JACK (A/V OUT)
< SWITCH > ************************************************************

S001 1-762-805-21 SWITCH, PUSH (1 KEY)(LENS COVER OPEN) A-1176-924-A MS-305 BOARD, COMPLETE
************************************************************ **********************

A-1176-923-A CD-617 BOARD, COMPLETE < CAPACITOR >

**********************
(IC002 is not included in this COMPLETE board.) C301 1-100-786-91 TANTAL. CHIP 22uF 20% 6.3V
C302 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
< CAPACITOR >
< CONNECTOR >
C002 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V
C004 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V * CN301 1-816-644-51 FFC/FPC CONNECTOR (LIF) 12P
C005 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V CN302 1-817-827-11 MEMORY STICK DUO CONNECTOR
C006 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C007 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < FERRITE BEAD >

C009 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V FB301 1-469-581-21 INDUCTOR, FERRITE BEAD (1005)
FB302 1-469-581-21 INDUCTOR, FERRITE BEAD (1005)
< CONNECTOR > FB303 1-469-581-21 INDUCTOR, FERRITE BEAD (1005)
FB304 1-469-581-21 INDUCTOR, FERRITE BEAD (1005)
* CN001 1-816-057-51 CONNECTOR, FPC (ZIF) 39P FB305 1-218-990-81 SHORT CHIP 0 (Note1)

< IC > FB306 1-218-990-81 SHORT CHIP 0 (Note1)

IC001 8-753-230-85 IC CXA3691EN-T9 < RESISTOR >

IC002 A-1176-035-A CCD BLOCK ASSY (CCD IMAGER)
(IC002 is not included in this COMPLETE of R302 1-218-953-11 RES-CHIP 1K 5% 1/16W
CD-617 board.) R303 1-218-940-11 RES-CHIP 82 5% 1/16W
R304 1-218-940-11 RES-CHIP 82 5% 1/16W
< TRANSISTOR > ************************************************************

Q001 6-550-119-01 TRANSISTOR DTC144EMT2L A-1176-908-A PL-045 BOARD, COMPLETE

**********************
< RESISTOR > (RY201 is not included in this COMPLETE board.)

R001 1-218-990-81 SHORT CHIP 0 < CAPACITOR >

R002 1-218-990-81 SHORT CHIP 0
R003 1-218-982-11 RES-CHIP 270K 5% 1/16W C201 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
R004 1-218-989-11 RES-CHIP 1M 5% 1/16W
R007 1-218-979-11 RES-CHIP 150K 5% 1/16W < CONNECTOR >

R010 1-218-977-11 RES-CHIP 100K 5% 1/16W * CN201 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P
R011 1-218-990-81 SHORT CHIP 0
************************************************************ < DIODE >

A-1176-978-A CK-161 FLEXIBLE BOARD, COMPLETE D202 8-719-988-61 DIODE 1SS355TE-17

****************************** D203 6-500-776-01 DIODE MAZW068H0LS0

< CONNECTOR > < RELAY >

* CN001 1-817-391-51 CONNECTOR, FPC (ZIF) 31P RY201 1-455-038-11 SOLENOID, PLUNGER
************************************************************ (RY201 is not included in this COMPLETE of
PL-045 board.)

Be sure to read “Precautions upon replacing CCD imager” Note 1:

on page 4-1 when changing the CCD imager. Resistor is mounted to the location where FB305
and FB306 are printed.

DSC-H5_L2
5-10
 PL-045 ST-142 ST-144 SW-471 SY-150

Ref. No. Part No. Description Ref. No. Part No. Description
< SWITCH > < RESISTOR >

S201 1-786-179-31 SWITCH, PUSH (1KEY)(FLASH POP UP) R001 1-216-121-11 RES-CHIP 1M 5% 1/10W
************************************************************ R002 1-216-097-11 RES-CHIP 100K 5% 1/10W
************************************************************
A-1176-909-A ST-142 BOARD, COMPLETE
********************** A-1176-922-A SW-471 BOARD, COMPLETE
(C105 is not included in this COMPLETE board.) ***********************

< CAPACITOR > < CONNECTOR >

C101 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V * CN401 1-815-333-51 CONNECTOR, FPC (ZIF) 33P
C102 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V * CN402 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P
C103 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
0 C105 1-112-763-11 CAP, ELECT 320uF 330V < DIODE >
(C105 is not included in this COMPLETE of
ST-142 board.) D401 8-719-064-07 DIODE SML-310LTT86 (ACCESS)
D402 6-500-776-01 DIODE MAZW068H0LS0
C106 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V D403 8-719-056-23 DIODE MA2S111-(K8).SO

< CONNECTOR > < RESISTOR >

* CN101 1-816-644-51 FFC/FPC CONNECTOR (LIF) 12P R401 1-208-671-11 METAL CHIP 330 0.5% 1/16W
R402 1-218-970-11 RES-CHIP 27K 5% 1/16W
< DIODE > R403 1-218-962-11 RES-CHIP 5.6K 5% 1/16W
R404 1-218-970-11 RES-CHIP 27K 5% 1/16W
D101 8-719-056-54 DIODE MAZS068008SO R405 1-218-962-11 RES-CHIP 5.6K 5% 1/16W
0 D102 6-501-096-01 DIODE CRF02 (TE85R)
< COMPOSITION CIRCUIT BLOCK >
< IC >
RB401 1-234-376-11 RES, NETWORK 2.2K (1005X4)
IC101 6-707-555-01 IC TPS65552RGTR RB402 1-234-376-11 RES, NETWORK 2.2K (1005X4)

< COIL > < SWITCH >

L101 1-456-995-22 INDUCTOR 4.7uH S401 1-786-157-11 SWITCH, TACTILE (RIGHT)

S402 1-786-157-31 TACTILE SWITCH (DUST)
< TRANSISTOR > S403 1-786-157-11 SWITCH, TACTILE (DOWN)
S404 1-786-157-11 SWITCH, TACTILE (UP)
Q101 6-550-891-01 TRANSISTOR GT8G133 (T2LSONY.Q) S405 1-786-157-11 SWITCH, TACTILE (SET)

< RESISTOR > S406 1-786-157-11 SWITCH, TACTILE (LEFT)

S407 1-786-525-31 TACTILE SWITCH (ZOOM T)
R103 1-243-975-11 METAL CHIP 4.7M 5% 1/16W S408 1-786-157-11 SWITCH, TACTILE (DISP)
R104 1-218-935-11 RES-CHIP 33 5% 1/16W S409 1-786-525-31 TACTILE SWITCH (ZOOM W)
S410 1-786-157-11 SWITCH, TACTILE (MENU)
< TRANSFORMER > ************************************************************

0 T101 1-443-850-21 DC-DC CONVERTER TRANSFORMER, SY-150 BOARD, COMPLETE

************************************************************ **********************
************************************************************
A-1176-914-A ST-144 BOARD, COMPLETE
**********************

< CAPACITOR >

Electrical parts list of the SY-150 board is not
shown.
C002 1-100-758-11 CERAMIC CHIP 0.047uF 10% 250V Pages from 5-12 to 5-15 are not shown.
C003 1-100-761-21 CERAMIC CHIP 0.01uF 10% 250V

< DIODE >

D001 6-500-811-01 DIODE RR255L-400TE25

< COIL >

L001 1-456-193-11 COIL, TRIGGER

• Refer to page 5-1 for mark 0.

DSC-H5_L2
5-11E
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]

Toolbar

Printing a text Reversing the screens displayed once

1. Click the Print button . • To reverse the previous screens (operation) one by one, click
2. Specify a printer, print range, number of copies, and other op- the .
tions, and then click [OK]. • To advance the reversed screens (operation) one by one, click
the .
Application of printing:
To set a range to be printed within a page, select the graphic
Application to the Service Manual:
selection tool and drag on the page to enclose a range to
This function allows you to go and back between circuit dia-
be printed, and then click the Print button. gram and printed circuit board diagram, and accordingly it
will be convenient for the voltage check.

Finding a text
1. Click the Find button . Moving with link
2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary) 1. Select either palm tool , zoom tool , text selection tool
, or graphic selection tool .
Application to the Service Manual: 2. Place the pointer in the position in a text where the link exists
To execute “find” from current page toward the previous pages, (such as a button on cover and the table of contents page, or
select the check box “Find Backward” and then click the blue characters on the removal flowchart page or drawing
“Find”. page), and the pointer will change to the forefinger form .
3. Then, click the link. (You will go to the link destination.)

Moving with bookmark:

Click an item (text) on the bookmark pallet, and you can move
to the link destination. Also, clicking can display the
hidden items.
(To go back to original state, click )
3. Open the find dialog box again, and click the [Find Again] and
you can find the matched character strings displayed next.
(Character strings entered previously are displayed as they are
in the text box.)

Application to the Service Manual:

The parts on the drawing pages (block diagrams, circuit dia-
grams, printed circuit boards) and parts list pages in a text
can be found using this find function. For example, find a
Ref. No. of IC on the block diagram, and click the [Find Again]
continuously, so that you can move to the Ref. No. of IC on Zooming or rotating the screen display
the circuit diagram or printed circuit board diagram succes- “Zoom in/out”
sively. • Click the triangle button in the zoom control box to select the
Note: The find function may not be applied to the Service display magnification. Or, you may click or for zoom-
Manual depending on the date of issue.
ing in or out.

Switching a page
• To move to the first page, click the .
• To move to the last page, click the . “Rotate”
• To move to the previous page, click the . • Click rotate tool , and the page then rotates 90 degrees each.

• To move to the next page, click the .

Application to the Service Manual:
The printed circuit board diagram you see now can be changed
to the same direction as the set.
 Reverse 985211731.pdf

Revision History

S.M. Rev.
Ver. Date History Contents
issued
1.0 2006.04 Official Release — —

DSC-H5_L2