DSC-T1

SERVICE MANUAL LEVEL 2

Ver 1.3 2004. 04
DSC-T1
US Model
Canadian Model
Revision History AEP Model
UK Model
E Model
Hong Kong Model
How to use Australian Model
Acrobat Reader Korea Model
Chinese Model
Tourist Model
Japanese Model

Link

SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS

SERVICE NOTE FRAME SCHEMATIC DIAGRAMS REPAIR PARTS LIST

DISASSEMBLY SCHEMATIC DIAGRAMS

• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987628053.pdf).

• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987628043.pdf).
• Reference No. search on printed wiring boards is available.
On the LD-140, MS-148 and SY-95 boards
This service manual provides the information that is premised the circuit board replacement service and not intended repair
inside the LD-140, MS-148 and SY-95 boards.
Therefore, schematic diagram, printed wiring board, waveforms, mounted parts location and electrical parts list of the LD-140,
MS-148 and SY-95 boards are not shown.
The following pages are not shown.
Schematic diagram ............................. Pages 4-15 to 4-36 Mounted parts location ............................. Pages 4-54 to 4-55
Printed wiring board ............................ Pages 4-45 to 4-52 Electrical parts list ................................... Pages 5-7 to 5-11

DIGITAL STILL CAMERA

DSC-T1

SPECIFICATIONS
x Camera [General] x AC-LM5 AC Adaptor
[System] Used battery pack Power requirements
Image device NP-FT1 100 to 240 V AC, 50/60 Hz
7.66 mm (1/2.4 type) color CCD Power requirements Current consumption
Primary color filter 3.6 V 0.2 A
Total pixels number of camera Power consumption (during shooting) Power consumption
Approx. 5 255 000 pixels 1.6 W 10 W
Effective pixels number of camera Operating temperature Rated output voltage
Approx. 5 090 000 pixels 0°C to +40°C (+32°F to +104°F) 4.2 V DC, 1.5 A
Lens Carl Zeiss Vario-Tessar Storage temperature Operating temperature
3× zoom lens –20°C to +60°C (–4°F to +140°F) 0°C to +40°C (+32°F to +104°F)
f = 6.7 – 20.1 mm (38 – 114 mm when Dimensions Storage temperature
converted to a 35 mm still camera) 91 × 60 × 21 mm –20°C to +60°C (–4°F to +140°F)
F3.5 – 4.4 (3 5/8 × 2 3/8 × 2 7/32 inches) Dimensions
Exposure control (W/H/D, excluding maximum Approx. 47 × 30 × 80mm
Automatic exposure, Scene selection protrusions) (1 7/ 8 × 1 3/16 × 31/4 inches)
(8 modes) Mass Approx. 180 g (6.3 oz) (including (W/H/D, excluding projecting parts)
White balance battery pack NP-FT1, “Memory Stick Mass Approx. 170 g (6.0 oz) excluding
Automatic, Daylight, Cloudy, Duo” and wrist strap) power cord (mains lead)
Fluorescent, Incandescent, Flash Built-in microphone
File format (DCF compliant) Electret condenser microphone x NP-FT1 battery pack
Still images: Exif Ver. 2.2 JPEG Built-in speaker
compliant, DPOF compatible Used battery
Piezo-electric speaker Lithium-ion battery
Audio with still image: MPEG1
compliant (Monaural) Exif Print Compatible Maximum voltage
Movies: MPEG1 compliant PRINT Image Matching II Compatible DC 4.2 V
(Monaural) Nominal voltage
Recording media DC 3.6 V
“Memory Stick Duo” xUC-TA USB cradle Capacity 2.4 Wh (680 mAh)
Flash Recommended distance (ISO set to [Input and Output connectors]
Auto): A/V OUT (MONO) jack (Monaural)
0.3 m to 1.5 m (11 7/8 inches to Minijack x Accessories
59 1/8 inches) (W) Video: 1 Vp-p, 75 Ω, unbalanced, • AC-LM5 AC Adaptor (1)
0.5 m to 1.5 m (19 3/4 inches to sync negative
59 1/8 inches) (T) Audio: 327 mV (at a 47 kΩ load) • Power cord (mains lead) (1)
Output impedance 1 kΩ • UC-TA USB cradle (1)
[Input and Output connectors] USB jack B • USB cable (1)
Multi connector USB connection • NP-FT1 battery pack (1)
High-Speed USB • A/V connecting cable (1)
[LCD screen] (USB 2.0 High-Speed compatible)
• Wrist strap (1)
LCD panel DC IN jack
• “Memory Stick Duo” (32 MB) (1)
6.2 cm (2.5 type) TFT drive Camera connector
• Memory Stick Duo Adaptor (1)
Total number of dots
211200 (960×220) dots • CD-ROM (USB driver SPVD-013) (1)
• Operating instructions (1)

Design and specifications are subject to change

without notice.

—2—
 DSC-T1

CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point : LEAD FREE MARK
them out to the customer and recommend their replacement. Unleaded solder has the following characteristics.
4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than
of deterioration. Point them out to the customer and ordinary solder.
recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified.
Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350°C.
• Keep the temperature of the soldering iron around 270˚C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
• Do not touch the soldering iron on the same conductor of the • Strong viscosity
circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than
• Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such
or unsoldering. as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

—3—
DSC-T1

TABLE OF CONTENTS
1. SERVICE NOTE ........................................................ 1-1 5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS ······················································ 5-1
2. DISASSEMBLY 5-1-1. OVERALL SECTION ···················································· 5-3
2-1. DISASSEMBLY ······························································ 2-1 5-1-2. BATTERY HOLDER SECTION ···································· 5-4
2-2. SERVICE POSITION ····················································· 2-3 5-1-3. CABINET (REAR) SECTION ······································· 5-5
2-3. CIRCUIT BOARDS LOCATION ··································· 2-5 5-2. ELECTRICAL PARTS LIST ·········································· 5-6
2-4. FLEXIBLE BOARDS LOCATION ································ 2-5
HELP (List of caution points is shown here.) Parts list of the SY-95, MS-148 and LD-140 boards
are not shown.
3. BLOCK DIAGRAMS Pages from 5-7 to 5-11 are not shown.
3-1. OVERALL BLOCK DIAGRAM (1/2) ··························· 3-1
3-2. OVERALL BLOCK DIAGRAM (2/2) ··························· 3-3
3-3. POWER BLOCK DIAGRAM (1/2) ································ 3-5
3-4. POWER BLOCK DIAGRAM (2/2) ································ 3-7

4. PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/2) ······················· 4-1
FRAME SCHEMATIC DIAGRAM (2/2) ······················· 4-3
4-2. SCHEMATIC DIAGRAMS
• CD-463 (CCD IMAGER)
SCHEMATIC DIAGRAM ······························ 4-7
• CN-198 (MULTI CONNECTOR)
SCHEMATIC DIAGRAM ······························ 4-9
• ST-86 (FLASH)
SCHEMATIC DIAGRAM ···························· 4-11
• CONTROL SWITCH BLOCK (PW-125)
SCHEMATIC DIAGRAM ···························· 4-13

Shematic diagram of the SY-95, MS-148 and LD-140

boards are not shown.
Pages from 4-15 to 4-36 are not shown.

4-3. PRINTED WIRING BOARDS

• CD-463 (CCD IMAGER)
PRINTED WIRING BOARD ······················· 4-41
• ST-86 (FLASH)
PRINTED WIRING BOARD ······················· 4-42
• CN-198 (MULTI CONNECTOR)
PRINTED WIRING BOARD ······················· 4-43

Printed wiring board of the SY-95, MS-148, LD-140

and FP-694 boards are not shown.
Pages from 4-45 to 4-52 are not shown.

4-4. MOUNTED PARTS LOCATION ································· 4-53

Mounted parts location of the SY-95, MS-148

and FP-695 boards are not shown.
Pages from 4-54 to 4-55 are not shown.

—4—
 DSC-T1
SECTION 1
SERVICE NOTE

• NOTE FOR REPAIR

Make sure that the flat cable and flexible board are not cracked of When remove a connector, don't pull at wire of connector.
bent at the terminal. Be in danger of the snapping of a wire.
Do not insert the cable insufficiently nor crookedly.

When installing a connector, don't press down at wire of connector.

Be in danger of the snapping of a wire.

Cut and remove the part of gilt

which comes off at the point.
(Take care that there are
some pieces of gilt left inside)

[Discharging of the FLASH unit’s charging capacitor]

The charging capacitor of the FLASH unit is charged up to the

maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-T1 is simply turned off. Therefore, the remaining
voltage must be discharged as described below.

Preparing the Short Jig

1 kΩ/1 W
To preparing the short jig. a small clip is attached to each end of a
resistor of 1 kΩ /1 W (1-215-869-11)
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.

Wrap insulating tape.

Discharging the Capacitor

Short circuits between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.

ST-86 B0ARD

Shorting jig
(1kΩ / 1w) Capacitor

1-1
DSC-T1

[Description on Self-diagnosis Display]

Self-diagnosis display
• C: ss: ss
The contents which can be handled
by customer, are displayed.
• E: ss: ss
The contents which can be handled
by engineer, are displayed.

Display Code Countermeasure Cause Caution Display During Error

C:32:01 Turn off the main power then back on. Trouble with hardware. SYSTEM ERROR

• The type of memory stick that cannot be

Replace the memory stick. used by this machine, is inserted.
C:13:01 MS ERROR
Format the memory stick with the DSC-T1. • Data is damaged.
• Unformatted memory stick is inserted.
Flash LED
Checking of flash unit or replacement of Abnormality when flash is being
E:91:01 Flash display
flash unit. charged.
Flashing at 3.2 Hz

E:01:XX

E:61:00 *1 Checking of lens drive circuit When failed in the focus initialization. —

E:61:10 *1

Note : The error code is cleared if the battery is removed, except defective flash unit.
*1: The error display is given in two ways.

1-2E
 DSC-T1
SECTION 2
DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY

Note: The power capacitor of the flash unit is charged up to 315 V maximum. If you touch
the capacitor terminal that is charged to high voltage, you will receive an electric
shock. This high voltage is not discharged even if you turned off the main power
HELP
3 Remove the control switch
of this set, and it residues. Discharge the residual voltage referring to the service block in the direction of the arrow. (Sheet attachment positions and procedures of processing
note (page 1-1). the flexible boards/harnesses are shown.)

1
2
1

1
1
1 1 FP-690 flexible Note: When re-assembling,
board (19P) confirm the switch position.
2 3 Lens section 2 ST-86 board,
ST terminal cover 1 FP-693 flexible board (16P)
3
2 Two claws
1 FP-695 board (21P) 1
2 CCD block 2
1
assembly (33P)
1 Five screws (M1.4 ´ 2.5), Note: Be careful not to drop
lock ace, p2 (special) the lens shaft. HELP 08

2 Cabinet (front) assembly (disassembly of the Battery holder section)

3 FP-695 board (Including the LD-140 board) SY
3 Lens shaft -9
5
HELP 01
2
5
7 CCD block 1 Copper leaf protection sheet
assembly 3 Battery holder
8 LSV-850A 2 Flexible board (from LSV-850A)(21P) section
HELP 02
3 FP-695 board (Including the LD-140 board)
4 Radiation sheet (CCD) 1 Turn over the control switch
HELP 03 5 Insulating sheet (CCD) block in the direction of the arrow.
HELP 06 4 6 Two tapping screws (B1.2 ´ 3.5) 2 LCD unit (ACX500EN-J) (25P)
6
Note: Do not peel off the radiation sheet as Note: The CCD imager is not supplied
much as possible. If you peel it off, be as a single unit since removing it
careful not to damage the flexible board. 1
as a single unit requires adjustment.

2 Mode knob

HELP 05 4 9 Cabinet (rear) assembly

HELP 07 1

2 7

3 8
5 6
5 Microphone
1
4 1 Four claws
2 LCD frame
6
3

1 Harness protection sheet 1

4 Block light 1
2 Two claws
3 Microphone holder guide plate
HELP 04
4 Two solderings 2
6 Microphone cushion

1 Tape (LCD) 5 Control switch block,

7 Control switch block 2 Four screws (M1.4 ´ 2.5), LCD frame
(PW-125) lock ace, p2 (special) 6 LCD unit (ACX500EN-J)
2 3 Screw (M1.4 ´ 2.5), Block light guide plate
lock ace, p2 (special) 7 Zoom button
3 LCD unit (ACX500EN-J) HELP 09 4 Slide the mode knob 8 SW button

1 Remove the solderings

2 Four claws

2-1 2-2
DSC-T1
2. DISASSEMBLY

2-2. SERVICE POSITION

2
[SERVICE POSITION TO CHECK THE SY-95 BOARD]
Note1: By using an adhesive tape, press the LENS COVER switch (S401).
Note2: When checking the VIDEO AMP (SY-95 board IC302) or the USB circuit, connect the cradle.

S401 LENS COVER switch (Note1)

1 (25P)
FP-693 flexible board (16P)
Control switch block (PW-125)
1 Mode knob

2 9 CN402
4 7
3 8
1 5 6

3
LCD unit (ACX500EN-J), CN701
1 1 Block light guide plate
CN703
2
SY-95 board

S
3 Y-
95
FP-690
MS-148 board flexible board (19P)
1
CN704
1 CN705
CN702
2 3
5
2 AC power CN-198 board
AC IN adaptor

2
ST-86 board

4 FP-695 board (21P)

S
Y- 3
95

1
5 1
2

3 4 CCD block
Lens section
1 assembly (33P)

2
Note : The power capacitor of the flash unit is charged up to 315 V maximum. If you touch
the capacitor terminal that is charged to high voltage, you will receive an electric
3 1 shock. This high voltage is not discharged even if you turned off the main power
of this set, and it residues. Discharge the residual voltage referring to the service
note (page 1-1).
1
2 5

SY
-9
3
5

2 1 4
3

2-3 2-4
 DSC-T1
2. DISASSEMBLY

2-3. CIRCUIT BOARDS LOCATION

MS-148

SY-95
ST-86

LD-140

CN-198

CD-463

NAME FUNCTION
CD-463 CCD IMAGER
CN-198 MULTI CONNECTOR
LD-140 LENS DRIVE
MS-148 MS I/O, LCD PANEL DRIVE
ST-86 FLASH
SY-95 CAMERA A/D CONVERTER, TIMING GENERATOR, CAMERA DSP, LENS CONTROL,
CAMERA SYSTEM CONTROL, HI CONTROL, AUDIO I/O, FLASH DRIVE,
DC/DC CONVERTER, CONNECTOR

2-4. FLEXIBLE BOARDS LOCATION

The flexible boards contained in the lens block are not shown.

FP-693

CONTROL SWITCH BLOCK

FP-694 (PW-125)

FP-691

FP-690
FP-695

2-5E
 DSC-T1

HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

HELP 01 HELP 02

LSV-850A

Adhesive sheet (LD)

FP-695
flexible board

LD-140 board

FP-695 board Radiation sheet (CCD)

HELP 03 HELP 04

Tape (LCD)

Insulating sheet (CCD)

HELP 05 HELP 06

Protection sheet (motor)

LSV-850A
Harness
protection sheet

Control switch block

(PW-125)

Copper leaf protection sheet

HELP
DSC-T1

HELP 07 HELP 09

Microphone holder

Two claws

Microphone
Sheet (BL)
Microphone
cushion Two solderings

(Black)

LCD unit (ACX500EN-J)

(Red)

Control switch block

(PW-125)

HELP 10 HELP 11

Light interception
sheet (L)

MS-148 board
MS protection sheet (S) SY-95 board LSV-850A

Sheet

SY
-95

MS protection sheet (L)

Radiation sheet (D)

Electrostatic sheet (K)

HELP
 DSC-T1

HELP 08
(disassembly of the Battery holder section)

9 Remove the
5 three solderings

7 Two claws
3 Screw
(M1.4 × 2.5),
lock ace, p2
(special)
4 Claw
8 SY holder

6 Screw
qa Three claws (M1.4 × 2.5),
1 Two claws lock ace, p2
2 Cap (multi) (special)

qd CN-198 board (6P)

qs Battery
SY terminal board
-95

q; CN-198 board (19P)

qf SY-95 board,
MS-148 board

qg Remove the
w; Battery holder
two solderings
assembly
5
-9
Y
S

qk Three claws

ql CN-198 board
qh MS-148 board

wd CN-198 board

wa Two solderings
5
-9
Y
S

ws Lithium battery
qj SY-95 board

HELP
 DSC-T1

3. BLOCK DIAGRAMS

Link

OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (1/2)

OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2)

 DSC-T1
SECTION 3 3. BLOCK DIAGRAMS
BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

LENS UNIT CD-463 BOARD

(LSV-850A) IRIS
The CCD imager is not supplied
as a single unit since removing it
SY-95 BOARD(1/2)
SHUTER as a single unit requires adjustment.
CA AD0
134,136,2,4,6 CA AD13
9,12,15,18,21 (AA,AB,Y)
IC001 Q004 CCD OUT
S/H
A/D CONV.
24,27,30,32
(AA,AB,AC,
(J,M,N,P
CCD IMAGER 17 BUFFER 30 86 CLP DM MC D0-D15 R,T,V,M)
64 CLP OB A18 U,V,W,Y)
(1/8) (21-24)
55 Y18
1-5,7-9 20
11-14 21-24
IC151
V1A,B H1A,B
21 37 TIMING (E-H,
V2 H2A,B (J,K,L,M,
22 42 GENERATOR MC A1-A25 J-M)
V3A,B RG N,P,R,T,U)
V4 24 48 (21-24)
25 51
V5A,B
V6 27 33 FP-691 MS-148
V7A,B CN702
V8
10,13 99
MCK TG
AC16 SYS V B16
FLEXIBLE BOARD(2/3)
D16 AA8
15-11,9-7,5-2
CN702
113,17
20,109 CA HD
MC CKIO A7
C15
A15
(2/2) 4,3,5,7,
2,8 CN101
112,115 49,105 CA F T23
125,119 66,101,120 H1 D15 MS SDIO/DATA0-3,MS BS, MS SCLK MEMORY
118,121 B15 STICK
AU LRCK
TG CLK AA7 C7 D16 6 DUO
84 (3/8) CONNECTOR
(2/8)
X151 (1/8)
126-129 123,3
IC501 C22
XACCESS LED
LED DRIVE
54MHz
XCAM RST
IC301 D103
XTAL
OSC
1 IC152 5
CAMERA
CAMERA
SYSTEM
SP+
Q102
(ACCESS)
CAM SO,SCK CONTROL
FREQUENCY DEVIDER CA HD DSP SP- SP901
CA F Y17
SPEAKER
EXT CLK AB18
CA F

LD-140 BOARD FP-695 HR DIR3A

HR DIR3B
N21
XMS IN
FLEXIBLE HR EN0
L21
P21 SYS V
HR DIR0A K20
IRIS A
IRIS HR DIR0B D13
IRIS A CN701 HR EN3 L22
MOTOR
18
IRIS B
IRIS B
G4
H4
IC001 G1
G2
18 HR DIR3A
HR DIR3B
HR EN2 J21
B13
C13
FR SO,SI,SCK

M 21 G5
IRIS DRIVE
H2
20
19
HR DIR2A
HR DIR2B
M21
M20
K2 XSYS RST
H6 G3 D14
N20
XFC RST SENS TO
FOCUS A F21 XAE LOCK ON
FOCUS XZM RST SENS AB5 OVERALL
FOCUS A HR EN2
MOTOR F20 XSHTR ON BLOCK DIAGRAM
8
FOCUS B
FOCUS B
A6
B5
C8
C7
15 HR DIR2A AB13
STRB CHG 2 (2/2)
M 11 A4
FOCUS MOTOR
DRIVE B8
17
16
HR DIR2B AD19
AC15
XSTRB FULL (PAGE 3-4)
B4 B7 XSTRB PWR ON
AB11
ZOOM A
ZOOM ZOOM A HR EN0
XUSB JACK IN
MOTOR ZOOM B C1 B3 HR DIR0A L4
12 Q504
12 D2 A2 HR DIR0B
M 15
ZOOM B
E1
ZOOM MOTOR
DRIVE B2
14
13 F1
PRELAMP AF CONT
E2 A1
SELF TIMER LED
H23

FOCUS RESET XFC RST SENS

5 8
SENSOR
ZOOM RESET XIR RST SENS
2 11
SENSOR
CN002
STRB ON
AB4
CN-198
FP-694 MS-148 BOARD
PANEL R
PANEL G Q302-Q304
BOARD(1/2)
FP-691 PANEL B
BUFFER
E23
J1 CN704
(1/3)
C23 XCAM RST
FLEXIBLE FLEXIBLE HDO D23 CA F
C23

AC12
K1
L1
USBPHY D+,D-
9 10
PANEL V C18 EXT CLK 8 12
A6 M1
(1/2) D17
AC12
AC9
AU A IN
AU A OUT
VR PANEL R (2/8) CN001
VG B11
8 (2/2) PANEL G V OUT
9
VB
D6
C7
C1
C2
PANEL B 2 IC302 4 F23 A11
MULTI
7
Q801,802
C6 IC803 B1 VIDEO AMP T20
C11
CONNECTOR
LCD901
PS1G RGB DRIVE
2.5INCH 10 BUFFER A7 XSYS RST
COLOR LCD A12
RGT,HCK1,2 CAM SO,SCK Q501
PANEL B12 MELODY
REF,HST HDO AD14 BEEP AU OUT
6 D1 MELODY EW MOD E1 (5/8) B4 4 16
WIDE,DWN Q805 AB7
11 G2,F3
EN,VCK, PANEL V V OUT
12
14
VST
E4,F4
F7,E5
TIMING GENERATOR D2 LPF
XSYS RST AU A IN
IC601 2 17

A3,B3 F5 H4
16 AU A OUT AUDIO
C3,A2 E3 H5 AMP/ADC A2
21 D1
F2 SYS SO,SI,SCK SYS SO,SI,SCK MIC901
24
F1 MIC IN
STRB ON B8 1 MIC
A4 BL LEV TO CN001
A5 OVERALL
ND901 1 BLOCK DIAGRAM
BACK 1 (2/2)
CONTROL SWITCH
LIGHT LED A
3
CN402
(PAGE 3-3) BLOCK(PW-125)
LED K
(1/2)

AUDIO SIGNAL
VIDEO SIGNAL
VIDEO/AUDIO SIGNAL

3-1 3-2
DSC-T1
3. BLOCK DIAGRAMS

3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

MS-148 BOARD FP-691 SY-95 BOARD CONTROL SWITCH

(4/8) FP-693
(3/3) FLEXIBLE (2/2) IC491
BLOCK(PW-125) (2/2)
FLEXIBLE
HI CONTROL
S101
S003-011,013
MODE SW
KEY AD0 J6 12 ZOOM,MENU,IMAGE SIZE/DELETE
KEY AD1 H6 13 DISPLAY/LCD BACK LIGHT,
J8 MODE DIAL UP,DOWN,RIGHT, LEFT,SET
KEY AD2 G6 14
S401
( LENS COVER
OPEN ) B7 XLENZ CAP OPN S001

CN-198 BOARD J4 32KHz IN

XPOWER ON B8 5 POWER
CN704 S002
(2/2) BT001 11
VL 3V X402
32.768KHz
J5 32KHz OUT
XAE LOCK ON
XSHTR ON
7
SHUTTER
LITHIUM 8
BATTERY
(SECONDARY) Q406 D004
12 XPWR LED ON B2 3 (POWER)
VBUS USB JACK IN
11 13 C8 XUSB JACK IN
14 D003
XCHARGE/XSTB LED B1 10
XMULTI JACK IN /CHG
CN001 13 15 C4 XMULTI JACK IN
XAV JACK IN
MULTI 14 18 A3 XAV JACK IN S012
CONNECTOR BATT/XEXT A7 BATT/XEXT 9
24 17 RESET
CN001

3 4
ACV UNREG
2 5
1 6
CN705

Q407
XAE LOCK ON
BATT SIG G2 BATT SI
I/F
G1 BATT SO XSHTR ON
XUSB JACK IN
J1 INIT CHARGE
F002 H2 FAST CHARGE Q404
ST UNREG
E8 SYS DD ON XMS IN
MS IN B6
F003
ACV UNREG
F001 TO
BATT UNREG FR SO D2 OVERALL
FR SI D1 BLOCK DIAGRAM
D015 D013
XFR SCK E1
FR SO,SI,SCK
2 (1/2)
(PAGE 3-2)
XSYS RST
XSYS RST B3
L8 C1 DDCON SO SYS V
DDCON SO,SCK SYS V B9
K8 D3 DDCON SCK
STRB CHG
D8 XSTRB PWR ON
XRSTX
RESET B7 D7 XRSTX
D011 XSTB FULL
A10
BACK UP VCC A5 SELF TIMER LED
B9 BACK UP VCC
H4 PRE LAMP AF CONT
3V
B11
REG
A11 EVER 3.0V

BT901 BATTERY IN BATT IN

D9 OUT8A A7 A9 BATT IN
BATTERY
TERMINAL C Q002 E9 OUT8B
DETECT
FP-690 ST-86 BOARD
8 1 D1 FLEXIBLE
BATTERY INIT CHARGE Q001,002
4 5 D2 CN703
CHARGER T002
D036 Q651,652
E5 1
ST UNREG
D4 6

FAST CHARGE HIGH XE A(H)

E4 FET DRIVE E3 Q653 VOLTAGE
STRB CHG
(1/2) CHARGER
XSTRB PWR ON C003
C7 SYS DD ON 15
D7 XSTRB FULL
(7/8) A 3.1V 16
Q653
D 1.2V
IC001 AU 2.8V
(2/2)

DC/DC CONVERTER D 2.8V

A 2.8V (6/8) XENON
CAM 15.0V TUBE
CAM -8.0V IC651
M 5V
Q003
ST 5V
STRB ON FLASH XE K(L)
4 IGBT DRIVE 2 17
DRIVE

STRB ON TO
BL LEV OVERALL
BLOCK DIAGRAM D003
LED A 1 (1/2)
SELF TIMER LED Q701 (AF LED)
LED K
(PAGE 3-1) LED DRIVE 19
PRE LAMP AF CONT
(7/8)

IC003 CAM -0.5V

(7/8)

IC007 D 1.8V

3-3 3-4
 DSC-T1
3. BLOCK DIAGRAMS

3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-95 BOARD(1/2)

F001
CN-198 BATT UNREG

BOARD F002
ST UNREG ST UNREG
CN705
1 4 F003
CN001 ACV UNREG ACV UNREG
2 5
MULTI FB701 LED A
3 6
CONNECTOR
(7/8)
BATT/XEXT LED K
24 17
VL 3V
BT001
11 IC001 BL LV
LITHIUM CN704 DC/DC CONVERTER
BATTERY
(SECONDARY) Q002
PANEL 13.5V

8 1 D1 VCC1A G11
VCC1B G10
4 5 VCC1C G9
BATT UNREG D4 BATTERY
BT901 E5 CHARGER OUT11A H11 L006 L003
BATT SIG AV 2.8V
BATTERY OUT11B H10
TERMINAL
C
INIT CHARGE OUT11C J11 L010
D2 A 2.8V
D026
OUT12A L11 (RECT)
FET
E4 D 2.8V
DRIVE OUT12B K10
FAST CHARGE OUT12C J9
E3

D013 L002 VCH1A L10 (7/8)

BATT UNREG E9 OUT8A VCH1B K9 D 1.8V
D9 OUT8B
VCH1C(FB4) L9
2 IC007 3

D015 L001 1.8V REG

ACV UNREG
B11 3V REG VCC2 F9 TO
EVER 3.0V L005 POWER
A11 D 1.2V BLOCK DIAGRAM
OUT2 F10
D011 1 (2/2)
A10 VCH2 E11 (PAGE 3-7)
L007

D8
OUT3A J3
M 5V
OUT3B K1
OUT3C J2 D017
(RECT)
A5
H8 BATT SENS BACK UP VCC B9 BATTERY IN
H4 VCH3A(FB3) J1
DETECT
VCH3B H4
CONTROL FP-693 XRST X D7 B7 RESET VCH3C(FB6) H3
SWITCH FLEXIBLE G8 ACV SENS ST 5V
BATT IN A9 A7 VCH3S H2
BLOCK
(PW-125) DDCON SO C1 L8 DIN
VCC GD H1
L008
A7 BATT/XEXT DDCON SCK D3 DDCON SO,SCK,XCS K8 CLK CAM 15.0V
Q407 XCS DD CON H1 OUT4 K6
K7 LD D023
G2 BATT SI (RECT)
I/F C7 VCH4 J6
G1 BATT SO SYS DD ON E8 SYS DD ON
S001 D7
POWER 5 B8 XPWR ON VCC5 K5
CAM -8.0V
OUT5 L5
INIT CHARGE J1
4 L009 D021
(RECT) 8 4
3 B2 XPOWER LED ON CAM -0.5V
FAST CHARGE H2 VCC+ VCC-
D004 (POWER) VCH5 J5
L004 3 SHUNT
11 1 Q001
LED A 2 REG
OUT6 F1
10 B1 XCHARGE/XSTRB LED DDCON SENS F8
D025
(RECT)
D003 /CHG VCH6 G1
(4/8) LED K
ICH6 G2 (7/8)
BL LV
REF6 B1
S012
IC491 IC003
RESET HI CONTROL CBG B5
9 -0.5V REG A 3.1V
VLD04 C8
CN001 PANEL 13.5V
VLD05 B8

D 1.2V

3-5 3-6
DSC-T1
3. BLOCK DIAGRAMS

3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-95 BOARD(2/2) FP-691 MS-148 BOARD

FLEXIBLE CN101
Q101
D 2.8V VCC MEMORY
9 STICK DUO LCD901
MS PWR ON CONNECTOR 2.5INCH
COLOR LCD
ST UNREG
PANEL 13.5V UNIT
20 (ACX500EN-J)
LED A

LED K
D 2.8V
BL LV

PANEL 13.5V IC803

AV 2.8V RGB DRIVE
AV 2.8V (5/8) BL LEV A5 TIMING GENERATOR
ND901
A4
IC601 BACK LIGHT

ST 5V AUDIO LED A
AMP/ADC 1
LED K
3
CN402

MS PWR ON
FP-694
AD18
(3/8)
Q651,652
CN703
1
Q001,002,T002 FLEXIBLE
A 2.8V IC501 AD51
STRB CHG
XSTRB PWR ON
ST UNREG
6
CAMERA AB11
D 2.8V XSTRB FULL STRB CHG
SYSTEM AC15
D 1.8V CONTROL
CAM DD ON
AC20 HIGH
D 1.2V XSTRB PWR ON VOLTAGE XE A(H) XENON
15 CHARGER
AMP OUT ON TUBE
A 3.1V F22 Q653 C003

A 2.8V

XSTRB FULL
Q302-304 16
PANEL
(2/8) R,G,B
BUFFER D003
Q305,306 MT 5V

1
TO
POWER
IC302 18 AF LED

BLOCK DIAGRAM
(1/2)
VIDEO AMP
FP-690
(PAGE 3-6) Q655,656 FLEXIBLE ST-86 BOARD

AU 2.8V (2/8)
(6/8)
A 2.8V
IC301
D 2.8V CAMERA
J22
XFC RST LED IC651
DSP XZM RST LED
D 1.2V V21 IGBT DRIVE

CN701
M 5V M 5V 1
2
IC001
ST 5V D 2.8V D 2.8V
3 IRIS/FOCUS/
LENS UNIT
ZOOM DRIVE (LSV-850A)
X151
(1/8)
54MHz
XTAL
IC152 OSC Q702
F RST VCC FOCUS
FREQUECY 7 6 RESET
DEVIDER SENSOR
XFC RST LED

CAM DD ON Q702
Z RST VCC ZOOM
Q151,152 RESET
10 3
CAM 15V SENSOR
33 XZM RST LED CN002
CAM -8.0V 17 IC001
CN702 CCD
FP-695
IMAGER
FLEXIBLE LD-140 BOARD
(1/8)
A 2.8V

CAM -0.5V IC151 CD-463 BOARD

A 3.1V S/H,A/D CONV.
TIMING
GENERATOR The CCD imager is not supplied
as a single unit since removing it
as a single unit requires adjustment.

3-7 3-8E
 DSC-T1
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS

SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/2)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

TO SY-95 BOARD(2/2)

A FRAME SCHEMATIC DIAGRAM(1/2)

SY-95 BOARD(1/2)
B CN702 33P
REG_GND 1

V8 2
V7B 3

V7A 4
V6 5
VHLD 6

V5B 7
C V5A 8

V4 9
VST 10 CN402 25P
V3B 11 1 LED_A
V3A 12 2 N.C.
V2 13 FP-694 3 LED_K
V1B 14
FLEXIBLE 4 BL_THH
V1A 15 5 BL_THL
D REG_GND 16 6 RGT

CD-463 BOARD CAM_-8.0V_CD

VSUB_CONT
17

18
7

8
VB

VR
SHT 19 9 VG
REG_GND 20 10 PSIG
H1A 21 11 HCK1
H1B 22 12 HCK2
REG_GND 23 MS-148 BOARD 13 CREXT
E H2A 24 14 REF
H2B 25 15 HST
REG_GND 26 16 WIDE
RG 27 17 REG_GND
REG_GND 28 18 VDDG
REG_GND 29 19 VSS
LCD901
CCD-OUT 30 20 VDD 2.5INCH
COLOR
REG_GND 31 21 DWN LCD UNIT
F POWER_SAVE 32
ND901
22 EN
(ACX500EN-J)

CAM_15V_CD 33 BACK LIGHT 23 VCK

24 VST

25 COM

CN704 19P
REG_GND(AU) 1

G V_OUT

REG_GND(AU)
2

3
CN101 10P
AU_OUT 4
27

29

1 GND
CN001 26P REG_GND(AU) 5
2 BS
1 ACV_UNREG ACV_UNREG 2 REG_GND(USB) 6
3 DATA1
3 ACV_UNREG LANC_DC 4 REG_GND(USB) 7
4 SDIO/DATA0
5 XLANC_JACK_IN LANC_SIG 6 USBPHY_D- 8 MEMORY
5 DATA2
7 USB_LED USB/LANC_GND 8 USBPHY_D+ 9 STICK
6 INT DUO

H 9 USB_HOST D+ 10 REG_GND(USB) 10
7 DATA3
CONNECTOR

11 USB_VBUS D- 12
CN-198 BOARD
VL_3V 11
FP-691 8 SCLK
13 XMULTI_IN XAV_JACK_IN 14 VBUS 12
15 EXT_STRB_ON A_OUT_L 16 VBUS 13 FLEXIBLE 9 VCC

10 GND
17 V_OUT A_OUT_R 18 VBUS 14

19 V_GND A_GND 20 XMULTI_IN 15

21 AUX AUX 22 NC 16
23 ACV_GND BATT/XEXT 24 BATT/XEXT 17

I 25 ACV_GND ACV_GND 26
BT001
XAV_JACK_IN 18

LITHIUN BATTERY NC 19
30
28

(SECONDARY)

MULTI CONNECTOR
CN705 6P
ACV_GND 1

ACV_GND 2
ACV_GND 3
ACV_UNREG0 4
J ACV_UNREG0 5
ACV_UNREG0 6

16

4-1 4-2 FRAME SCHEMATIC DIAGRAM (1/2)

DSC-T1
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS

FRAME SCHEMATIC DIAGRAM (2/2)

1 2 3 4 5 6 7 8 9 10 11

A FRAME SCHEMATIC DIAGRAM(2/2)

CN001 16P

10
11

12

13
14

15
16
1
2

3
4

5
6
7

8
9
MIC_IN
REG_GND

XPOWER_LED_ON
EVER_3.0V

XPOWER_ON
REG_GND
XAE_LOCK_ON

XSHTR_ON
XRESET_SW

XCHARGE/XSTRB_LED
EVER_3.0V

KEY_AD0

KEY_AD1
KEY_AD2

REG_GND
NC
CONTROL SWITCH BLOCK
(PW-125)

FP-693 FLEXIBLE

C
CN703 19P
STB_UNREG 1
STB_UNREG 2

STB_UNREG 3

ST-86 BOARD FP-690 STB_UNREG

STB_UNREG
4

5
D FLEXIBLE STB_UNREG 6

REG_GND 7
REG_GND 8
REG_GND 9

REG_GND 10
REG_GND 11

REG_GND 12

REG_GND 13
E REG_GND 14
XSTRB_PWR_SAVE 15
STB_FULL 16

IGBT_ON 17
AF_LED_5V 18

AF_LED_K 19

F SY-95 BOARD(2/2)
LENS UNIT
(LSV-850A)
CN002 21P
CN701 21P
Z_RST_GND 1
M_5V 1
Z_RST_SENS 2
M_5V 2
Z_RST_VCC 3
D_2.8V 3
F_RST_GND 4
REG_GND 4
G F_RST_SENS
F_RST_VCC
5
6
REG_GND 5

REG_GND 6
N.C 7
F_RST_VCC 7
FOCUS_A 8
XFC_RST_SENS 8
FOCUS_B 9

FOCUS_A 10 FP-695 LENS_TEMP

Z_RST_VCC
9

10
FOCUS_B 11
FLEXIBLE XZM_RST_SENS 11
ZOOM_A 12
HR_EN0 12
H ZOOM_A 13
HR_DIR0B 13
ZOOM_B 14
HR_DIR0A 14
ZOOM_B 15
HR_EN2 15
TEMP_OUT 16
HR_DIR2B 16
TEMP_GND 17
HR_DIR2A 17
IRIS_A 18
HR_EN3 18
IRIS_A 19
HR_DIR3B 19
IRIS_B 20
HI_DIR3A 20
I IRIS_B 21
XCAM_DR_PS 21

LD-140 BOARD

J
16 TO SY-95 BOARD(1/2)

FRAME SCHEMATIC DIAGRAM (2/2) 4-3 4-4

 DSC-T1

4-2. SCHEMATIC DIAGRAMS

Link

CD-463 BOARD (CCD IMAGER) ST-86 BOARD (FLASH)

CN-198 BOARD (MULTI CONNECTOR) CONTROL SWITCH BLOCK (PW-125)

COMMON NOTE FOR SCHEMATIC DIAGRAMS

 DSC-T1
4-2. SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS

(In addition to this, the necessary note is printed in each block)

(For schematic diagrams) 1. Connection

• All capacitors are in µF unless otherwise noted. pF : µ
Link
µF. 50 V or less are not indicated except for electrolytics Pattern box
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum About 30cm
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example C541 L452
22U 10UH
TA A 2520

Kinds of capacitor
Front of the lens
Temperature characteristics
External dimensions (mm)

• Constants of resistors, capacitors, ICs and etc with XX

indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with * differ according to the model/destination. 2. Adjust the distance so that the output waveform of
Refer to the mount table for each function. Fig. a and the Fig. b can be obtain.
• All variable and adjustable resistors have characteristic
H
curve B, unless otherwise noted.
Yellow

Magenta
White
Cyan
• Signal name Green
XEDIT → EDIT PB/XREC → PB/REC

Red
Blue
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line
• J : IN/OUT direction of (+,–) B LINE. A B A=B B A
• C: adjustment for repair. Fig. a (Video output terminal output waveform)
• A: VIDEO SIGNAL (ANALOG)
• A: AUDIO SIGNAL (ANALOG)
• A: VIDEO/AUDIO SIGNAL (ANALOG)
• A: VIDEO/AUDIO/SERVO SIGNAL
• A: SERVO SIGNAL
• Circled numbers refer to waveforms.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values Fig.b (Picture on monitor TV)
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used) When indicating parts by reference number, please
• Voltage values change depending upon input include the board name.
impedance of VOM used.)
Note : Note :
Precautions Upon Replacing CCD imager The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
• The CD-463 board mounted as a repair part is not equipped 0 are critical for safety. pour la sécurité.
with a CCD imager. Replace only with part number Ne les remplacer que par une
When replacing this board, remove the CCD imager from specified. pièce portant le numéro spécifié.
the old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
• As the CCD imager may be damaged by static electricity
from its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.

4-5
 DSC-T1
4-2. SCHEMATIC DIAGRAMS CD-463 PRINTED WIRING BOARD

4-2. SCHEMATIC DIAGRAMS For Schematic Diagram

• Refer to page 4-41 for printed wiring board.

1 2 3 4 5 6 7 8 9

CD-463 BOARD
CCD IMAGER
A XX MARK:NO MOUNT

NO MARK:REC/PB MODE

14 13 12 11 10 9 8 7 6 5 4 3 2 1

SIGNAL PATH

V8
V7B
V7A
V6

Vhld
V5B

V5A
V4
Vst
V3B
V3A

V2
V1B

V1A

ICX473CQZ-13
C VIDEO SIGNAL IC001
CCD IMAGER
CHROMA Y Y/CHROMA

CCD-OUT
REC
The CCD imager is not supplied

IC001
CSUB
Rss3

GND
GND

GND

SUB
H2B
H2A

H1B
H1A
as a single unit since removing it

RG
VH
PB

VL
as a single unit requires adjustment.
15 16 17 18 19 20 21 22 23 24 25 26 27 28

D
14.9 Q004 C002
2SC4250(T5LSONY1) 0.1u
BUFFER 16V
B

R001
CAM_15V_CD 1500
R002
22k C004
POWER_SAVE 3.5
10.6 5p
R003
E REG_GND
3900
1005
CH
R005
CCD_OUT 0 1200
Q002 0 Q001
REG_GND DTC144EUA-T106 DTC144EUA-T106
SWITCH SWITCH
REG_GND

RG
R006 C001
REG_GND 0 0.1u R004
16V B 1800
H2B 12
C005
H2A 0
0.1u

F REG_GND
Q003
16V B

H1B
DTC144EHT2L
H1A SWITCH
TO
REG_GND
SY-95 BOARD
(1/8) C003
SHT 0.1u
CN702
16V
(PAGE 4-15 VSUB_CONT
B
of LEVEL3) CAM_-8.0V_CD
REG_GND

G V1A

V1B
V2

V3A
V3B

VST

V4
V5A

H V5B

VHLD
V6
V7A
16
V7B

V8
REG_GND

4-7 4-8 CD-463

DSC-T1
4-2. SCHEMATIC DIAGRAMS CN-198 PRINTED WIRING BOARD

For Schematic Diagram

• Refer to page 4-43 for printed wiring board.

1 2 3 4 5 6 7 8 9 10 11 12
CN-198 BOARD
MULTI CONNECTOR
A XX MARK:NO MOUNT

NC
XAV_JACK_IN

BATT/XEXT FB001
0uH
NC

XMULTI_IN FB002
0uH
VBUS
C001
B TO
VBUS 100p
CH
VBUS
SY-95 BOARD
(8/8) VL_3V
CN704
REG_GND(USB)
(PAGE 4-30

2
3 2 3 2 CN001
of LEVEL3) USBPHY_D+ LND026 R004
0 MULTI
USBPHY_D- 4 1 4 1 STATIC_GND CONNECTOR

3
4
REG_GND(USB) D001 D002 D003
MA4L11100AS0 DF3A8.2C(TPL3) DF3A8.2C(TPL3)
REG_GND(USB) 26P

2
REG_GND(AU) ACV_UNREG ACV_UNREG
3 2

4
3
AU_OUT ACV_UNREG LANC_DC

6
5
REG_GND(AU) 4 1 XLANC_JACK_IN LANC_SIG
D004

8
7
V_OUT USB_LED USB/LANC_GND
DF3A8.2C(TPL3)

26 24 22 20 18 16 14 12 10
9
REG_GND(AU) USB_HOST D+
R002 100k

25 23 21 19 17 15 13 11
USB_VBUS D-

XMULTI_IN XAV_JACK_IN

2
R001

1
EXT_STRB_ON A_OUT_L
47k
D D005
DF3A8.2C(TPL3)
V_OUT

V_GND
A_OUT_R

A_GND
R003

4
0 AUX AUX
LF001 ACV_GND BATT/XEXT
1 3
ACV_GND ACV_GND
2 4

FB003
0uH

E
D008
XX

D009
DF3A8.2C (TPL3) R005
XX

F
ACV_GND
TO
ACV_GND
SY-95 BOARD
(8/8) ACV_GND
CN705
ACV_UNREG0
(PAGE 4-30 ACV_UNREG0
Note : Note :
of LEVEL3) BT001
The components identified by Les composants identifiés par
ACV_UNREG0
LITHIUM mark 0 or dotted line with mark une marque 0 sont critiques
BATTERY 0 are critical for safety.
(SECONDARY) SIGNAL PATH pour la sécurité.
G Replace only with part number
specified.
Ne les remplacer que par une
pièce portant le numéro spécifié.
VIDEO SIGNAL
AUDIO
16
CHROMA Y Y/CHROMA SIGNAL

REC
PB

CN-198 4-9 4-10

 DSC-T1
4-2. SCHEMATIC DIAGRAMS ST-86 PRINTED WIRING BOARD

For Schematic Diagram

• Refer to page 4-42 for printed wiring board.

1 2 3 4 5 6 7 8 9

ST-86 BOARD
FLASH
A XX MARK:NO MOUNT T002
CONVERTER
NO MARK:REC/PB MODE TRANSFORMER D002
HAU160C030STP
CL001
P S
STB_UNREG 4 5
REG_GND LND001
XSTRB_PWR_ON 1 XE_A(H)
TO C002
FP-690 FLEXIBLE 0.01u
STB_FULL B R008
(PAGE 4-26 F + 1M
IGBT_ON 3
B of LEVEL3)
AF_LED_5V
R001 R005
AF_LED_K 4700 180 2 LND003
XENON
TUBE TRIGGER_IN
Q001
CPH3205-SONY-TL-E LND004
0
0 R003 TRIGGER GND
120
Q001,002 C003
HIGH VOLTAGE 63u –
CHARGER 315V
Q002
MCH3405-TL-E

C 0 0
XE_K(L)
Q003
CY25AAJ-8-T13
LND002
FLASH DRIVE
2.7 268
C004

6
8
7

5
47000pF
R002
100k R004
10k

R006
47

4
3

2
1
0
D CL002
R007
1M

D001
CL003 MA111-(K8).S0

CL004

CL005

E CL006

D003 Note : Note :

S4G49(SONY)
The components identified by Les composants identifiés par
CL007 (AF LED)
mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.

F
16

4-11 4-12 ST-86

DSC-T1
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS

1 2 3 4 5 6 7 8 9

CONTROL SWITCH BLOCK(PW-125)

A CN001 16P
MIC901
MIC_IN 1
REG_GND 2 (MIC) SIGNAL PATH
XPOWER_LED_ON 3

EVER_3.0V 4
D004 AUDIO
XPOWER_ON 5 (POWER) R001
470
TO REG_GND 6
SIGNAL
SY-95 BOARD
(8/8) XAE_LOCK_ON 7
S001
B THROUGH
THE FP-693
XHTR_SW

XRESET_SW
8

9
POWER
FLEXIBLE
XCHARGE/XSTRB_LED 10
(PAGE 4-29
of LEVEL3) EVER_3.0V 11
KEY_AD0 12
KEY_AD1 13

KEY_AD2 14
R007
REG_GND 15 S002 1500
(Shutter) S006
C NC 16 S010

R006
3300

S012 S008

RESET

D D003 S005 S011 R009

3300
/CHG

R002
240

R005
1500

R008
S003 S004 1200
E W (ZOOM) T
R004
1200
R003
1200 S009 S013

(Display/LCD back light

(Image Size
/DELETE) on/off)

S007

F MENU

16

Schematic diagram of the LD-140, MS-148

and SY-95 boards are not shown.
Pages from 4-15 to 4-36 are not shown.

CONTROL SWITCH BLOCK 4-13 4-14

 DSC-T1

4-3. PRINTED WIRING BOARDS

Link

CD-463 BOARD CN-198 BOARD

ST-86 BOARD

COMMON NOTE FOR PRINTED WIRING BOARDS

MOUNTED PARTS LOCATION CIRCUIT BOARDS LOCATION FLEXIBLE BOARDS LOCATION

NAME FUNCTION
CD-463 CCD IMAGER
CN-198 MULTI CONNECTOR
LD-140 LENS DRIVE
MS-148 MS I/O, LCD PANEL DRIVE
ST-86 FLASH
SY-95 CAMERA A/D CONVERTER, TIMING GENERATOR, CAMERA DSP, LENS CONTROL,
CAMERA SYSTEM CONTROL, HI CONTROL, AUDIO I/O, FLASH DRIVE,
DC/DC CONVERTER, CONNECTOR
 DSC-T1
4-3. PRINTED WIRING BOARDS

THIS NOTE IS COMMON FOR WIRING BOARDS

(In addition to this, the necessary note is printed in each block)

(For printed wiring boards)

• : Uses unleaded solder. • Chip parts.
• : Pattern from the side which enables seeing. Transistor Diode
(The other layers’ patterns are not indicated) C 6 5 4 4 5 6 5 4 4 5 3 3 3 1 23
• Through hole is omitted.
• Circled numbers refer to waveforms.
B E 1 2 3 3 2 1 1 2 3 3 2 1 2 1 2 1 2 1 6 54
• There are a few cases that the part printed on diagram
1 2 2 1 3 4 1 2 3 4 4 3 3 4
isn’t mounted in this model.
• C: panel designation
5 4 3 3 4 5 2 1 4 3 2 1 1 2 2 1
6 4 3
5 4

1 3 1 1 2
3

BOARD INFORMATION
parts location pattern
board name CSP IC
(shown on page) number of layers layers not shown
CD-463 4-53 2 – –
ST-86 4-53 4 2 and 3 –
CN-198 4-53 4 – –
FP-694 – 2 – –
LD-140 4-54 4 2 and 3 IC001
FP-695 – 1 – –
MS-148 4-55 6 2 to 5 IC803
IC001, IC151, IC301,
SY-95 4-54 8 2 to 7
IC491, IC501, IC601

4-39
 DSC-T1
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS MOUNTED PARTS LOCATION

4-3. PRINTED WIRING BOARDS

• Refer to page 4-39 for common note for printed wiring board. • : Uses unleaded solder.

CD-463 BOARD ST-86 BOARD(SIDE A) ST-86 BOARD(SIDE B)

A A

R005
28 25 20 15 LND002

Q001
LND001

Q004
R003
R001
A

Q003
CL001 CL006 CL005

4
3
C004 C002 CL007
IC001

B C E
CL002 CL003

C001
C005
R004
Q002 CL004

T002
R006
C003
1 5 10 14 R002
LND004 LND003
B B

1
A D003 K

5
B

D002
C C

R001
Q001 R008

C
LND001 1-860-520- D001 C004
LND002
LND004
LND003
LND005
11 12
LND006 LND007
C003
C002 8 5

R003 R005
R004
LND008 LND009
LND010 LND011
LND012 LND013
LND014 LND015 R002

G
LND016
LND018
LND017
LND019 D Q003 D
LND020 LND021

D
LND022 LND023

S
D

Q002
LND024 LND025
LND026 LND027 1 4
LND028 LND029
LND030 LND031
LND032 LND033
R007 R006

1-860-525- 11 1-860-525-
16
1 2 3 4 5
11
E E
The CCD imager is not supplied
as a single unit since removing it
as a single unit requires adjustment.
16
1 2 3 3 2 1 16

4-41 4-42 CD-463/ST-86

DSC-T1
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS MOUNTED PARTS LOCATION

• Refer to page 4-39 for common note for printed wiring board. • : Uses unleaded solder.

CN-198 BOARD(SIDE A)
A

D001
1 4 R004 R002
D005 C001

R005
1 4
2 3
2 3
2 1

D004

R001
1 4
2 3
FB001 R003 3
B FB003 3 4
D009

D002 D008
FB002 1 2
2 1 1-860-527- 21
LF001

D003
3 2
4 1

3 2
4 1
2
CAUTION :
C BT001 Danger of explosion if battery is incorrectly replaced.
LITHIUM BATTERY Replace only with the same or equivalent type.
(SECONDARY)
1

16
1 2 3 4 5 6

CN-198 BOARD(SIDE B)
A

1 5 15 25

2 10 20 26

CN001
1-860-527- B
21

MULTI CONNECTOR
C
Printed wiring board of the FP-695, MS-148,
SY-95 and FP-694 boards are not shown.
Pages from 4-45 to 4-52 are not shown.
6 5 4 3 2 1 16

CN-198 4-43 4-44

 DSC-T1
4-3. PRINTED WIRING BOARDS

4-4. MOUNTED PARTS LOCATION no mark : side A

* mark : side B
CD-463 BOARD ST-86 BOARD CN-198 BOARD
C001 A-4 C002 D-1 BT001 C-2
C002 A-5 C003 D-2
C003 A-4 * C004 C-1 C001 B-3
C004 A-4
C005 A-4 D001 C-1 * CN001 B-3
* D002 C-1
IC001 A-3 D003 B-3 D001 B-3
D002 B-3
Q001 A-4 Q001 C-1 D003 B-3
Q002 A-5 Q002 D-1 D004 B-3
Q003 A-4 * Q003 D-1 D005 B-3
Q004 A-5 D008 B-3
R001 C-1 D009 B-4
R001 A-4 R002 D-1
R002 B-5 R003 D-1 FB001 B-3
R003 A-4 R004 D-1 FB002 B-3
R004 A-4 R005 D-1 FB003 B-3
R005 A-4 * R006 D-1
R006 A-4 * R007 D-1 LF001 B-3
* R008 C-1
R001 B-4
R002 B-4
* T002 B-2 R003 B-3
R004 B-3

Mounted parts location of the LD-140, MS-148,

and SY-95 boards are not shown.
Pages from 4-54 to 4-55 are not shown.

4-53E CD-463/ST-86/CN-198
 DSC-T1

NOTE

5. REPAIR PARTS LIST

NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.

Link EXPLODED VIEWS

SY
-9
5

A B

OVERALL SECTION BATTERY HOLDER SECTION CABINET (REAR) SECTION

Link ELECTRICAL PARTS LIST ACCESSORIES

CD-463 BOARD ST-86 BOARD A MS-148 BOARD B

CN-198 BOARD B LD-140 BOARD A SY-95 BOARD B

 DSC-T1
5. REPAIR PARTS LIST

NOTE:
• -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number,
the original one. please include the board name.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or
• The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety.
supplied. Replace only with part number specified.
• Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque
the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
• CAPACITORS:
le numéro spécifié.
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...

5-1
 DSC-T1
5. REPAIR PARTS LIST

5-1. EXPLODED VIEWS

5-1-1. OVERALL SECTION
ns : not supplied

Cabinet (rear) section

7 (See page 5-5)

SY
-9
5
B
A

2 6
Battery holder section
(See page 5-4)
5
4 ns 7
1 3

LD-140 board 9
(Note 1)
17
B

15 18
14 8
A

13
12
7 16
10
Note 1: LD-140 board is included in the FP-695 complete board .
LD-140 board is not supplied as an independent service parts. CD-463 board
CCD imager (Note 2)
Note 2: CD-463 board is included in the CCD block assy. (Note 3)
CD-463 board is not supplied as an independent service parts. 11
Note 3: The CCD imager is included in the CCD block assy .
The CCD imager is not supplied as a single unit since
removing it as a single unit requires adjustment. Be sure to read “Precautions upon replacing CCD imager”
on page 4-5 when changing the CCD imager.

Ref. No. Part No. Description Ref. No. Part No. Description
1 X-3953-789-1 CABINET (FRONT) ASSY 10 A-7111-623-A CCD BLOCK ASSY (Supplied with CD-463 board)
2 3-087-670-01 GASKET (K) 11 3-086-156-11 SCREW B1.2
3 A-7078-867-A ST-86 BOARD, COMPLETE 12 3-086-238-01 SHEET (CCD), INSULATING
04 1-478-385-11 LUMINOUS UNIT, STROBOSCOPE 13 3-086-276-01 SHAFT, LENS
5 1-860-515-11 FP-690 FLEXIBLE BOARD 14 3-086-237-01 SHEET (LD), ADHESIVE

6 3-086-275-01 COVER, ST TERMINAL 15 A-7078-877-A FP-695 BOARD, COMPLETE

7 3-086-218-01 SCREW (M1.4), LOCK ASE, SPECIAL 16 3-088-401-01 SHEET, PROTECTION, COPPER LEAF
8 3-086-236-01 SHEET (CCD), RADIATION 17 3-089-986-01 SHEET (L), LIGHT INTERCEPTION
9 A-7113-001-A LENS ASSY (SERVICE EXCLUSIVE) 18 3-089-781-01 SHEET (MOTOR), PROTECTION

Note : Note :
The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.
5-3
DSC-T1
5. REPAIR PARTS LIST

5-1-2. BATTERY HOLDER SECTION 60

ns : not supplied
61
SP901
63
59
51 58
ns

MS 64
-14
8

53
54

65

ns
SY-95 board
(Note) 52
BT901
57

SY
-95

55 BT001
56
ns

64

68 67 66
72 69
Note : SY-95 board is included in the SY-MS complete board .
SY-95 board is not supplied as a single board since
removing it as a single board requires adjustment.
71
: BT001 (Lithium battery) CN-198 board on the mount position. (See page 4-43)

CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

Ref. No. Part No. Description Ref. No. Part No. Description
51 A-7079-000-A SY-MS BOARD, COMPLETE (SERVICE) 63 3-086-221-01 SHEET (SPEAKER), ADHESIVE
52 1-860-517-11 FP-693 FLEXIBLE BOARD 64 3-086-218-01 SCREW (M1.4), LOCK ASE, SPECIAL
53 1-860-516-11 FP-691 FLEXIBLE BOARD 65 3-086-223-01 SHEET (L), PROTECTION, MS
54 X-3953-783-1 HOLDER ASSY, BATTERY 66 3-086-219-01 HOLDER, SY
55 3-086-216-01 FOOT, RUBBER 67 A-7078-870-A CN-198 BOARD, COMPLETE

56 3-086-210-02 LID, BT 68 3-086-217-01 CAP (MULTI)

57 3-355-424-01 SCREW, TAPPING 69 3-089-013-02 SHEET (K), ELECTROTATIC
58 A-7078-865-A MS-148 BOARD, COMPLETE 71 3-089-985-01 SHEET
59 1-860-518-11 FP-694 FLEXIBLE BOARD 72 3-086-220-01 SHEET (SY), SLIDE
60 3-086-222-01 SHEET (S), PROTECTION, MS BT901 1-780-061-11 TERMINAL BOARD, BATTERY

61 3-086-752-01 CUSHION (RING) SP901 1-825-644-11 BUZZER, PIEZOELECTRIC

5-4
 DSC-T1
5. REPAIR PARTS LIST

5-1-3. CABINET (REAR) SECTION

ns : not supplied
110
108 107
106
115

114 ns

111
109
MIC901 105
112 104
113 LCD901

116

ND901

103

117

101 102

Ref. No. Part No. Description Ref. No. Part No. Description
101 3-086-279-01 TAPE (LCD) 111 3-086-277-01 CUSHION, MICROPHONE
102 3-086-218-01 SCREW (M1.4), LOCK ASE, SPECIAL 112 3-086-274-01 HOLDER, MICROPHONE
103 3-086-234-01 FRAME, LCD 113 3-086-278-01 SHEET, PROTECTION, HARNESS
104 3-086-232-01 BUTTON, SW 114 3-086-206-01 SHEET METAL, MODE RETAINER
105 3-086-233-01 BUTTON, ZOOM 115 3-086-207-01 SPRING (MODE), CLICK

106 X-3953-782-1 CABINET (REAR) ASSY 116 3-088-260-01 SHEET (BL)

107 3-086-199-01 BASE, MODE 117 3-090-940-01 SHEET (LCD)
108 3-086-198-01 KNOB, MODE LCD901 8-753-052-81 ACX500EN-J (2.5 INCH COLOR LCD UNIT)
109 3-086-200-01 SLIDER, MODE MIC901 1-542-554-11 MICROPHONE
110 1-478-171-11 SWITCH BLOCK,CONTROL (PW-125) ND901 1-478-250-11 BLOCK LIGHT GUIDE PLATE (2.5)

5-5
DSC-T1
CD-463 CN-198 ST-86

5-2. ELECTRICAL PARTS LIST

Ref. No. Part No. Description Ref. No. Part No. Description
A-7111-623-A CCD BLOCK ASSY < LINE FILTER >
***************
not supplied CD-463 BOARD, COMPLETE LF001 1-456-583-11 COIL, COMMON MODE CHOKE
**********************
(CD-463 board is included in CCD BLOCK ASSY.) < RESISTOR >

< CAPACITOR > R001 1-218-973-11 RES-CHIP 47K 5% 1/16W

R002 1-218-977-11 RES-CHIP 100K 5% 1/16W
C001 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R003 1-216-295-91 SHORT CHIP 0
C002 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R004 1-216-864-11 SHORT CHIP 0
C003 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V ************************************************************
C004 1-164-845-11 CERAMIC CHIP 5PF 0.25PF 50V
C005 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V A-7078-867-A ST-86 BOARD, COMPLETE
********************
< IC >
0 1-478-385-11 LUMINOUS UNIT, STROBO SCOPE
IC001 not supplied CCD IMAGER (Note) 1-860-515-11 FP-690 FLEXIBLE BOARD

< TRANSISTOR > < CAPACITOR >

Q001 8-729-029-14 TRANSISTOR DTC144EUA-T106 C002 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
Q002 8-729-029-14 TRANSISTOR DTC144EUA-T106 0 C003 1-100-760-11 ELECT 63uF 99% 315V
Q003 8-729-052-64 TRANSISTOR DTC144EHT2L C004 1-137-723-21 CERAMIC CHIP 0.047uF 10% 250V
Q004 8-729-050-22 TRANSISTOR 2SC4250 (T5LSONY1)
< DIODE >
< RESISTOR >
D001 8-719-073-01 DIODE MA111-(K8).S0
R001 1-218-955-11 RES-CHIP 1.5K 5% 1/16W 0 D002 6-500-237-01 DIODE HAU160C030TP
R002 1-218-969-11 RES-CHIP 22K 5% 1/16W D003 6-500-804-01 DIODE S4G49 (SONY)
R003 1-218-960-11 RES-CHIP 3.9K 5% 1/16W
R004 1-218-956-11 RES-CHIP 1.8K 5% 1/16W < TRANSISTOR >
R005 1-218-954-11 RES-CHIP 1.2K 5% 1/16W
Q001 6-550-308-01 TRANSISTOR CPH3205-SONY-TL-E
R006 1-218-990-11 SHORT CHIP 0 Q002 8-729-056-01 TRANSISTOR MCH3405-TL-E
************************************************************ Q003 8-729-053-74 TRANSISTOR CY25AAJ-8-T13

A-7078-870-A CN-198 BOARD, COMPLETE < RESISTOR >

*******************
R001 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
< BATTERY > R002 1-218-977-11 RES-CHIP 100K 5% 1/16W
R003 1-218-942-11 RES-CHIP 120 5% 1/16W
0 BT001 1-528-999-51 BATTERY (LITHIUN BATTERY (SECONDARY)) R004 1-218-965-11 RES-CHIP 10K 5% 1/16W
R005 1-218-944-11 RES-CHIP 180 5% 1/16W
< CAPACITOR >
R006 1-216-805-11 METAL CHIP 47 5% 1/10W
C001 1-164-874-11 CERAMIC CHIP 100PF 5% 50V R007 1-216-857-11 METAL CHIP 1M 5% 1/10W
R008 1-216-121-11 RES-CHIP 1M 5% 1/10W
< CONNECTOR >
< TRANSFORMER >
CN001 1-816-929-11 CONNECTOR, MULTIPLE 26P
0 T002 1-437-987-31 TRANSFORMER , CONVERTER
< DIODE > ************************************************************

D001 8-719-077-54 DIODE MA4L11100AS0 Be sure to read “Precautions upon replacing CCD imager”
D002 8-719-077-57 DIODE DF3A8.2C (TPL3)
on page 4-7 when changing the CCD imager.
D003 8-719-077-57 DIODE DF3A8.2C (TPL3)
D004 8-719-077-57 DIODE DF3A8.2C (TPL3)
D005 8-719-077-57 DIODE DF3A8.2C (TPL3) Note :
D009 8-719-077-57 DIODE DF3A8.2C (TPL3) The CCD imager is not supplied as a single unit
since removing it as a single unit requires adjustment.
< FERRITE BEAD >

FB001 1-500-284-21 INDUCTOR, FERRITE BEAD CAUTION :

FB002 1-500-284-21 INDUCTOR, FERRITE BEAD Danger of explosion if battery is incorrectly replaced.
FB003 1-414-228-11 INDUCTOR, FERRITE BEAD Replace only with the same or equivalent type.

Note : Note :
The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.
5-6
 LD-140 MS-148 SY-95

Ref. No. Part No. Description Ref. No. Part No. Description
A-7078-877-A FP-695 BOARD, COMPLETE
**********************
not supplied LD-140 BOARD, COMPLETE
**********************
(LD-140 board is included in FP-695 board)

************************************************************

A-7078-865-A MS-148 BOARD, COMPLETE

***********************
(CN402 is not included in this complete board.)

************************************************************

A-7079-000-A SY-MS BOARD, COMPLETE (SERVICE)

*******************************
not supplied SY-95 BOARD, COMPLETE
*********************
(MS-148 board and SY-95 board are included in SY-MS board.)
(IC301 is not included in this complete board.)

************************************************************

Electrical parts list of the LD-140, MS-148

and SY-95 boards are not shown.
Pages from 5-7 to 5-11 are not shown.
DSC-T1

Checking supplied accessories.

Make sure that the following accessories are supplied with your camcorder.

Power cord (Main lead) (1) AC-LM5 AC Adaptor (1) UC-TA USB cradle (1) USB cable (1)
(AUS model) (Except US, CND) 1-817-742-11 1-828-073-11
0 1-696-819-11 0 1-477-488-12
Power cord (Main lead) (1) AC-LM5 AC Adaptor (1)
(AEP, E model) (US, CND)
0 1-769-608-11 0 1-477-488-21
Power cord (Main lead) (1)
(CH model)
0 1-782-476-13
Power cord (Main lead) (1)
A/V connecting cable (1) Wrist strap (1)
(UK, HK model)
1-824-111-11 3-086-283-01
0 1-783-374-11
Power cord (Main lead) (1)
(JE model) CD-ROM
0 1-790-732-12 (USB Driver SPVD-013) (1)
Power cord (Main lead) (1) (AEP, UK, E, HK, AUS, CH,
(J model) JE, KR model)
0 1-791-637-13 3-087-330-01
Power cord (Main lead) (1) CD-ROM
(KR model) (USB Driver SPVD-013 (I)) (1) 2-pin conversion adaptor (1) 2-pin conversion adaptor (1)
0 1-776-985-11 (US, CND, J model) (JE model) (E, HK model)
Power cord (Main lead) (1) 3-087-331-01 1-569-007-12 1-569-008-12
(US, CND model)
0 1-790-107-22

• Abbreviation
CND : Canadian model
AUS : Australian model
CH : Chinese model
NP-FT1 battery pack (1) “Memory stick Duo” (1) Memory stick Duo Adaptor(1) HK : Hong Kong model
(not supplied) (MSA-M32A) (MSAC-M2) KR : Korea model
(not supplied) (not supplied) JE : Tourist model
J : Japanese model

Other accessories
3-085-733-01 MANUAL, INSTRUCTION SET (JAPANESE) (J) 3-085-733-61 MANUAL, INSTRUCTION SET (RUSSIAN/SWEDISH) (AEP)
3-085-733-11 MANUAL, INSTRUCTION SET (ENGLISH) (EXCEPT KR, J) 3-085-733-71 MANUAL, INSTRUCTION SET (ARABIC) (E)
3-085-733-21 MANUAL, INSTRUCTION SET (FRENCH/GERMAN) 3-085-733-81 MANUAL, INSTRUCTION SET (KOREAN) (JE, KR)
(CND, AEP) 3-085-734-01 MANUAL, INSTRUCTION (for PC)(JAPANESE) (J)
3-085-733-31 MANUAL, INSTRUCTION SET (SPANISH/PORTUGUESE)
Note : Note :
(AEP, E, JE)
The components identified by Les composants identifiés par
3-085-733-41 MANUAL, INSTRUCTION SET (ITALIAN/DUTCH) (AEP) mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
3-085-733-51 MANUAL, INSTRUCTION SET (CHINESE) (E, HK, CH, JE) Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.

5-12E
DSC-T1

Sony EMCS Co. 2004D1600-1

9-876-280-32 ©2004.4
— 52 — Published by DI Technical Support Section
 DSC-T1
LEVEL 1
2
US Model
SERVICE MANUAL Canadian Model
AEP Model
Ver 1.1 2004.03
UK Model
E Model
Hong Kong Model
Australian Model
Korea Model
Chinese Model
Tourist Model
Japanese Model
SUPPLEMENT-1
File this supplement-1 with the service manual.
(PV03-016)

• Addition of Black Model.

5. REPAIR PARTS LIST : Added portion.

Page Before change After change

Checking supplied accessories.

5-12E
UC-TA USB cradle (1) Wrist strap (1) UC-TA USB cradle (1) Wrist strap (1)
1-817-742-11 3-086-283-01 1-817-742-11 (SILVER) 3-086-283-01 (SILVER)
1-817-742-21 (BLACK) 3-086-283-11 (BLACK)
DSC-T1

5-1. EXPLODED VIEWS : Added portion.

Page Before change After change

5-1-1. OVERALL SECTION

Ref. No. Part No. Description Ref. No. Part No. Description
1 X-3953-789-1 CABINET (FRONT) ASSY 1 X-3953-789-1 CABINET (FRONT) ASSY (SILVER)
1 X-2021-386-1 CABINET (FRONT) (B) ASSY (BLACK)
5-3
7 3-086-218-01 SCREW (M1.4), LOCK ASE, SPECIAL 7 3-086-218-01 SCREW (M1.4), LOCK ASE, SPECIAL
(SILVER)

7 3-086-218-11 SCREW (M1.4), LOCK ASE, SPECIAL

(BLACK)

5-1-2. BATTERY HOLDER SECTION

54 X-3953-783-1 HOLDER ASSY, BATTERY 54 X-3953-783-1 HOLDER ASSY, BATTERY (SILVER)
54 X-2021-390-1 HOLDER (B) ASSY, BATTERY (BLACK)
5-4 56 3-086-210-01 LID, BT 56 3-086-210-01 LID, BT (SILVER)
56 3-086-210-11 LID, BT (BLACK)
68 3-086-217-01 CAP (MULTI) 68 3-086-217-01 CAP (MULTI) (SILVER)
68 3-086-217-11 CAP (MULTI) (BLACK)

5-1-3. CABINET (REAR) SECTION

104 3-086-232-01 BUTTON, SW 104 3-086-232-01 BUTTON, SW (SILVER)
104 3-086-232-11 BUTTON, SW (BLACK)
105 3-086-233-01 BUTTON, ZOOM 105 3-086-233-01 BUTTON, ZOOM (SILVER)
105 3-086-233-11 BUTTON, ZOOM (BLACK)
106 X-3953-782-1 CABINET (REAR) ASSY 106 X-3953-782-1 CABINET (REAR) ASSY (SILVER)
106 X-2021-388-1 CABINET (REAR) (B) ASSY (BLACK)
5-5 107 3-086-199-01 BASE, MODE 107 3-086-199-01 BASE, MODE (SILVER)
107 3-086-199-11 BASE, MODE (BLACK)
108 3-086-198-01 KNOB, MODE 108 3-086-198-01 KNOB, MODE (SILVER)
108 3-086-198-11 KNOB, MODE (BLACK)
110 1-478-171-11 SWITCH BLOCK,CONTROL (PW-125) 110 1-478-171-11 SWITCH BLOCK,CONTROL (PW-125)
(SILVER)

110 1-478-171-21 SWITCH BLOCK, CONTROL (PW-125)

(BLACK)

2004C1600-1
9-876-280-83 Sony EMCS Co. ©2004.3
—2— Published by DI CS Strategy Div.
 DSC-T1
LEVEL 1
2
US Model
SERVICE MANUAL Canadian Model
AEP Model
Ver 1.2 2004.03
UK Model
E Model
Hong Kong Model
Australian Model
Korea Model
Chinese Model
Tourist Model
Japanese Model
SUPPLEMENT-2
File this supplement-2 with the service manual.
(PV03-018)

• Change of parts number.

• Addition of Accessory.

5. REPAIR PARTS LIST : Changed portion. : Added portion.

Page Before change After change

Checking supplied accessories.

CD-ROM CD-ROM
(USB Driver SPVD-013) (1) (USB Driver SPVD-013) (1)
(AEP, UK, E, HK, AUS, CH, (AEP, UK, E, HK, AUS, CH,
JE, KR model) JE, KR model)
3-087-330-01 3-087-330-11
CD-ROM CD-ROM
(USB Driver SPVD-013 (I)) (1) (USB Driver SPVD-013 (I)) (1)
5-12E (US, CND, J model) (US, CND, J model)
3-087-331-01 3-087-331-11

UPDATE CD-ROM (PB), T1

3-091-965-01

2004C1600-1
©2004.3
9-876-280-86 Sony EMCS Co. Published by DI CS Strategy Div.
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]

Toolbar

Printing a text Reversing the screens displayed once

1. Click the Print button . • To reverse the previous screens (operation) one by one, click
2. Specify a printer, print range, number of copies, and other op- the .
tions, and then click [OK]. • To advance the reversed screens (operation) one by one, click
the .
Application of printing:
To set a range to be printed within a page, select the graphic
Application to the Service Manual:
selection tool and drag on the page to enclose a range to
This function allows you to go and back between circuit dia-
be printed, and then click the Print button. gram and printed circuit board diagram, and accordingly it
will be convenient for the voltage check.

Finding a text
1. Click the Find button . Moving with link
2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary) 1. Select either palm tool , zoom tool , text selection tool
, or graphic selection tool .
Application to the Service Manual: 2. Place the pointer in the position in a text where the link exists
To execute “find” from current page toward the previous pages, (such as a button on cover and the table of contents page, or
select the check box “Find Backward” and then click the blue characters on the removal flowchart page or drawing
“Find”. page), and the pointer will change to the forefinger form .
3. Then, click the link. (You will go to the link destination.)

Moving with bookmark:

Click an item (text) on the bookmark pallet, and you can move
to the link destination. Also, clicking can display the
hidden items.
(To go back to original state, click )
3. Open the find dialog box again, and click the [Find Again] and
you can find the matched character strings displayed next.
(Character strings entered previously are displayed as they are
in the text box.)

Application to the Service Manual:

The parts on the drawing pages (block diagrams, circuit dia-
grams, printed circuit boards) and parts list pages in a text
can be found using this find function. For example, find a
Ref. No. of IC on the block diagram, and click the [Find Again]
continuously, so that you can move to the Ref. No. of IC on Zooming or rotating the screen display
the circuit diagram or printed circuit board diagram succes- “Zoom in/out”
sively. • Click the triangle button in the zoom control box to select the
Note: The find function may not be applied to the Service display magnification. Or, you may click or for zoom-
Manual depending on the date of issue.
ing in or out.

Switching a page
• To move to the first page, click the .
• To move to the last page, click the . “Rotate”
• To move to the previous page, click the . • Click rotate tool , and the page then rotates 90 degrees each.

• To move to the next page, click the .

Application to the Service Manual:
The printed circuit board diagram you see now can be changed
to the same direction as the set.
Reverse 987628034.pdf

Revision History

S.M. Rev.
Ver. Date History Contents
issued
1.0 2003.10 Official Release — —
1.1 2004.03 Supplement-1 Addition of Black Model No
1.2 2004.03 Supplement-2 • Change of parts number. No
• Addition of Accessory.
1.3 2004.04 Revised-1 • Addition of Suplied parts. Yes
• Addtion of Error code.
• Part number suffix of CD-463 board is
changed to 12.