MDX-65

SERVICE MANUAL US Model

Canadian Model
AEP Model
UK Model
E Model

Dolby noise reduction extension manufactured under license Model Name Using Similar Mechanism MDX-62
from Dolby Laboratories Licensing Corporation.
Mini Disc Mechanism Type MG-798K-133
“DOLBY” and the double-D symbol a are trademarks of Dolby
Laboratories Licensing Corporation. Optical Pick-up Name KMS-241A/J2N

SPECIFICATIONS FEATURES
System Mini disc digital audio system • Sony BUS system compatible with mobile MD
Laser Diode Properties changers.
Material: GaAlAs • Direct-in system for inserting and removing
Wavelength: 780 nm MDs easily.
Emission Duration: Continuous • No waiting time to change discs in continuous
Laser output Power: Less than play.
44.6 µW* • The MD changer compartment has a built in light
* This output is the value measured at a distance of for easy use even in the dark.
200 mm from the objective lens surface on the • 1 bit Digital/Analog converter for high quality
Optical Pick-up Block. sound reproduction.

Frequency response
10 – 20,000 Hz
Wow and flutter Below measurable limit
Signal-to-noise ratio
95 dB
Outputs Bus control output (8 PIN)
Analog audio output (RCA PIN)
Current drain 300 mA (MD playback)
600 mA (during loading or ejecting a
disc)
Dimensions Approx. 176 × 83.5 × 142 mm
(7 × 3 3/8 × 5 18/32 in.) (w/h/d) not incl.
projecting parts and controls
Mass Approx. 1.1 kg (2 lb. 7 oz.)
Power requirement
12 V DC car battery (negative
ground)
Supplied accessories
Mounting hardware (1 set)
Bus cable 5.5 m (1)
RCA pin cord 5.5 m (1)

• U.S. and foreign patents licensed from Dolby

Laboratories Licensing Corporation.
• Design and specifications subject to change without
notice.

MINIDISC CHANGER

MICROFILM

–1–
 SERVICE NOTE TABLE OF CONTENTS

CAUTION 1. SERVICE NOTE

Use of controls or adjustments or performance of proce- 1-1. To Place the Set into Playback Mode ................................. 3
dures other than those specified herein may result in haz- 1-2. How to Check the Servo Board Waveforms ...................... 3
ardous radiation exposure.
2. GENERAL
Preparations ............................................................................ 4
Notes on Chip Component Replacement Listening MDs ........................................................................ 4
• Never reuse a disconnected chip component. Connections ............................................................................ 5
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat. 3. DISASSEMBLY
3-1. Panel (Rear) Assy ............................................................... 6
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR 3-2. Case (Upper) ...................................................................... 6
BASE UNIT 3-3. Panel (Front) Assy .............................................................. 7
The laser diode in the optical pick-up block may suffer electrostatic 3-4. MD Block ........................................................................... 7
breakdown because of the potential difference generated by the 3-5. Main Board ........................................................................ 8
charged electrostatic load, etc. on clothing and the human body. 3-6. Chassis (OP) Block ............................................................ 8
During repair, pay attention to electrostatic breakdown and also use 3-7. Servo Board ........................................................................ 9
the procedure in the printed matter which is included in the repair 3-8. Optical Pick-up .................................................................. 9
parts. 3-9. Note on Assembly for the Chassis (OP) Block ................ 10
The flexible board is easily damaged and should be handled with
care. 4. DIAGRAMS
4-1. IC Pin Descriptions .......................................................... 11
NOTES ON LASER DIODE EMISSION CHECK
4-2. Circuit Boards Location ................................................... 14
The laser beam on this model is concentrated so as to be focused on
4-3. Block Diagram ................................................................. 15
the disc reflective surface by the objective lens in the optical pick-up
4-4. Printed Wiring Boards –Servo Section– .......................... 17
block. Therefore, when checking the laser diode emission, observe
4-5. Schematic Diagram –Servo Section– ............................... 21
from more than 30 cm away from the objective lens.
4-6. Schematic Diagram –Main Section– ................................ 23
4-7. Printed Wiring Boards –Main Section– ........................... 26
NOTES ON PICK-UP FLEXIBLE BOARD
4-8. Printed Wiring Board –Power Section– ........................... 29
The pick-up flexible board in this set is secured to the optical pick-up
4-9. Schematic Diagram –Power Section– .............................. 31
with an adhesive tape. Once the tape is removed, an adhering force
becomes weak, and it cannot be reused.
5. EXPLODED VIEWS
Therefore, if the optical pick-up is replaced, replace also the pick-up
5-1. Case Section ..................................................................... 38
flexible board with a new one.
5-2. Main Board Section ......................................................... 39
5-3. MD Section (1) ................................................................. 40
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
5-4. MD Section (2) ................................................................. 41
(KMS-241A/J2N)
5-5. MD Section (3) ................................................................. 42
The laser diode in the optical pick-up block may suffer electrostatic
break-down easily. When handling it, perform soldering bridge to
the laser-tap on the flexible board. Also perform measures against 6. ELECTRICAL PARTS LIST ....................................... 43
electrostatic break-down sufficiently before the operation. The
flexible board is easily damaged and should be handled with care.

laser-tap

OPTICAL PICK-UP FLEXIBLE BOARD

SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE
WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
IN SUPPLEMENTS PUBLISHED BY SONY. DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

–2–
 SECTION 1
SERVICE NOTE
1-1. TO PLACE THE SET INTO PLAYBACK MODE
The this set has no key control function and cannot be placed into
the Playback mode alone.
For key control, the this set is controlled through serial
communication with a master unit (car audio player, TV tuner or
source selector compatible with the Sony BUS system.)
To service the this set, the set should be connected as given below:

Master unit
MDX-65 (CDX-C880,
C880R, etc.)

BUS CONTROL OUT BUS CONTROL IN

1-2. HOW TO CHECK THE SERVO BOARD

WAVEFORMS
1. Remove the panel (rear) assy, case (upper) and panel (front) assy.
Then, remove the main board from the mechanism deck. (See
page 8 of “SECTION 3. DISASSEMBLY”.)
2. Remove the chassis (OP) block from the mechanism deck. (See
page 10 of “SECTION 3. DISASSEMBLY”.)
3. Short each bridge points BP1 and BP2 on the main board by
solder bridge.

– main board (conductor side) –

BP1

BP2

4. Connect the power board with the main board by the main
flexible board. Connect the main board with the servo board by
the servo flexible board.
5. Connect to a master unit. With the master unit OFF, press the
preset buttons 4 n 5 n 1 (2 seconds or more each) in this
turn to enter the TEST mode.
6. Open the doors and insert a disc in the chassis (OP) assy. Use
the SOURCE button on the master unit to select to MD to
playback.
7. Check the waveforms at each point on the servo board.

Note: After this check is completed, remove solder between

shorted bridge points BP1 and BP2 and open these points.

–3–
SECTION 2
GENERAL This section extracted from US,
Canadian, E model’s instruction manual.

–4–
–5–
 SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.

3-1. PANEL (REAR) ASSY

4 BVTT 2.6x6

6 panel (rear) assy

3 BVTT 2.6x6

2 PTT 2.6x8

5 CN901

1 cover

3-2. CASE (UPPER)

3 case (upper)

1 BVTT 2.6x6

2 BVTT 2.6x6

–6–
3-3. PANEL (FRONT) ASSY

3 panel (front) assy

1 claw

2 claw 4 CN620

3-4. MD BLOCK

4 tension spring (FL)

6 MD block
1 damper (798)

5 tension spring (FL)

2 damper (798)

3 tension spring (FL)

–7–
3-5. MAIN BOARD

3 escutcheon

6 chassis (front)

0 CN600

7 collar (EHS)
!¢ CN701 !¡ CN601
!™ CN500
5 lead stopper
4 screws
(M1.7) !∞ CN700
2 screws
1 cushion (M1.7)
9 CN602

!¶ special flat screws

(1.7x3)
!• MAIN board
8 sheet (MAIN PC board) !£ CN603
!§ cushion (MAIN)

3-6. CHASSIS (OP) BLOCK

9 worm wheel (ELV2)

7 bearing (ELV)
8 bearing (ELV)

6 chassis (OP) block

5 bearing (ELV)
4 bearing (ELV)

3 chassis (bottom) assy

2 precision screws
1 precision screws (P 1.7x1.8)
(P 1.7x1.8)

–8–
3-7. SERVO BOARD

3 screws
(M1.7x2.2) 6 CN100

5 CN300
7 SERVO board

1 CN200

2 Unsolder the
4 CN400 motor lead wires.

3-8. OPTICAL PICK-UP

1 screws
(K1.7x3.5)

2 optical pick-up

–9–
3-9. NOTE ON ASSEMBLY FOR THE CHASSIS (OP) BLOCK

1 worm wheel (ELV2)

3 bearing (ELV)
4 bearing (ELV)

5 chassis (OP) block

2 Turn the three feed

A
screw (ELV) assy fully in
the direction of arrows A. A

A
8 chassis (bottom) assy
6 bearing (ELV)
7 bearing (ELV)

0 precision screws
(P1.7x1.8)
B 9 precision screw
(P1.7x1.8)

!¢ gear (ELVC)
!™ gear (ELVA2)
B
B
!∞ polyethylene washer

!£ polyethylene washer

!¡Turn the three gear (ELVB) fully

in the direction of arrows B.

– 10 –
 SECTION 4
DIAGRAMS
4-1. IC PIN DESCRIPTIONS
• IC100 CXA2523AR (RF AMP)
Pin No. Pin Name I/O Pin Description
1 I I I-V converted RF signal input (I) from detector of optical pick-up.
2 J I I-V converted RF signal input (J) from detector of optical pick-up.
3 VC O Center voltage (+1.65 V) generation output
4–9 A–F I Signal input (A to F) from detector of optical pick-up.
10 PD I Quantity monitor input of light from laser diode of optical pick-up.
11 APC O Laser amplifier output to automatic power control circuit.
12 APCREF I Reference voltage input for laser power setting.
13 GND — GND
14 TEMPI I Temperature sensor connecting pin (Not used in this set.)
15 TEMPR O Reference voltage output for temperature sensor. (Not used in this set.)
16 SWDT I Write data signal input from System controller (IC600).
17 SCLK I Serial clock signal input from System controller (IC600).
18 XLAT I Serial latch signal input from System controller (IC600).
19 XSTBY I Standby signal input (“L” : Standby) (Fixed at “H” in this set.)
20 FOCNT I Center frequency control voltage input of internal circuit filter (BPF22, BPF3T and EQ).
21 VREF O Reference voltage output (Not used in this set.)
22 EQADJ I Center frequency setting input of internal circuit filter (EQ).
23 3TADJ I Center frequency setting input of internal circuit filter (BPF3T).
24 VCC — Power supply pin (+3.3 V)
25 WBLADJ I Center frequency setting input of internal circuit filter (BPF22).
26 TE O Tracking error signal output to CXD2652AR (IC200).
27 CSLED I Connecting pin for low pass filter condenser of sled error signal.
28 SE O Sled error signal output to CXD2652AR (IC200).
29 ADFM O FM signal output of ADIP.
30 ADIN I FM signal input of ADIP by AC combination.
31 ADAGC I External condenser connecting pin for AGC of ADIP.
32 ADFG O ADIP double FM signal output (22.05 kHz ± 1 kHz) to CXD2652AR (IC200).
33 AUX O Support signal (I3 signal/temperature signal) output (Not used in this set.)
34 FE O Focus error signal output to CXD2652AR (IC200).
35 ABCD O Quantity signal output of light to CXD2652AR (IC200).
36 BOTM O Bottom hold signal output of quantity signal (RF/ABCD) of light to CXD2652AR (IC200).
37 PEAK O Peak hold signal output of quantity signal (RF/ABCD) of light to CXD2652AR (IC200).
38 RF O Playback EFM RF signal output to CXD2652AR (IC200).
39 RFAGC I External condenser connecting pin of AGC circuit for RF.
40 AGCI I RF signal input by AC combination.
41 COMPO O User comparator output pin (Not used in this set.)
42 COMPP I User comparator input pin (Fixed at “L” in this set.)
43 ADDC I External condenser connecting pin for low frequency interception of ADIP amplifier.
44 OPO O External condenser connect pin for lower cut of ADIP amplifier.
45 OPN I User operational amplifier inversion input pin (Fixed at “L” in this set.)
46 RFO O RF signal output
47 MORFI I RF signal input of MO by AC combination.
48 MORFO O RF signal output of MO.

– 11 –
• IC600 µPD784216GC-027-8EU (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Pin Description
1 M1 O Elevator motor (M904) drive signal output
2 M1 O Elevator motor (M904) drive signal output
3 M2 O Loading motor (M903) drive signal output
4 M2 O Loading motor (M903) drive signal output
5 MDMON O Mechanism deck system power control output (“H” : Power ON)
6 LES I Loading end sensor detection switch (S902) input
7 SES I Store end sensor detection switch (S903) input
8 HOME I Home position detection switch (S901) input (“L” : Home position)
9 VDD — Power supply pin (+5 V)
10 X2 — Main system clock connecting pin (14 MHz)
11 X1 — Main system clock connecting pin (14 MHz)
12 VSS — GND
13 XT2 — Sub system clock connecting pin (32.768 kHz)
14 XT1 — Sub system clock connecting pin (32.768 kHz)
15 RESET — System reset input
16 BU IN I Backup OFF detection input (“L” : Backup OFF)
17 BUS ON I BUS OFF detection of SONY BUS. (“H” : BUS OFF)
18 SQ SY I Sub code Q sync input from CXD2652AR (IC200).
19 STR SW I STOP switch (S600) input
20 — O Not used.
21 CC XINT I Interruption status input from CXD2652AR (IC200).
22 — O Not used.
23 AVDD — Power supply for A/D converter. (+5 V)
24 AVREF0 — Reference voltage for A/D converter.
25 INIT I Initial input pin at reset.
26 TEMP I Thermistor connecting pin for temperature detection.
27 EHS I Elevator height position detection input
28, 29 — I Connect to GND.
30 – 32 — O Connect to GND.
33 AVSS — Analog GND
34 ERR PWM O Error data output (Not used in this set.)
35 — O Not used.
36 AVREF1 — Reference voltage for D/A converter.
37, 38 — O Not used.
39 — — Not used.
40 MD SI I Read data signal input from CXD2652AR (IC200).
41 MD SO O Write data signal output to CXA2523AR (IC100) and CXD2652AR (IC200).
42 MD CKO O Serial clock signal output to CXA2523AR (IC100) and CXD2652AR (IC200).
43 — O Not used.
44 — — Not used.
45 UNISI I Serial data input for SONY BUS.
46 UNISO O Serial data output for SONY BUS.
47 UNI CKI I Serial clock input for SONY BUS.
48 LINKOFF O Link control signal output for SONY BUS. (“H” : Link OFF)
49 — O Not used.
50 — I Not used.
51, 52 D-BASS1, 2 O Digital D-BASS select output 1, 2 (Not used in this set.)
53 – 55 — O Not used.
56 – 59 MNT0 – 3 O Monitor 0 – 3 signal input from CXD2652AR (IC200).
60 AGING O Not used.
61 AGCHK O Not used.
62 TFTON O Not used.

– 12 –
Pin No. Pin Name I/O Pin Description
63 — O Not used.
64 EE CS O Chip select output to EEPROM. (Not used in this set.)
65 EE CKO O Serial clock output to EEPROM. (Not used in this set.)
66 EE SIO I/O Data input from/output to EEPROM. (Not used in this set.)
67 SENS I Internal status input from CXD2652AR (IC200).
68 LIMIT SW I Optical pick-up innermost track limit position detection switch (S400) input
69 DOORSW I Front door open detection switch (S620) input (“L” : Open complete)
70 MD LAT O Serial latch signal output to CXA2523AR (IC100) and CXD2652AR (IC200).
71 MD RST O Reset signal output to CXD2652AR (IC200).
72 VSS — GND
73 MD ON O Servo system power control output (“H” : Power ON)
74 EMPH O O De-emphasis circuit control output (“H” : De-emphasis ON)
75 A ATT I Analog mute control input (“H” : Mute ON)
76 ILLON O Illumination lamp (PL620) light-up control output (“H” : Lamp light-up)
77 TSTSMD I Single mode setting pin (“L” : Single mode)
78 TSTCKO O Serial clock output to LED for TEST mode display. (Not used in this set.)
79 TSTSO O Serial data output to LED for TEST mode display. (Not used in this set.)
80 TSTMOD I TEST mode setting pin (“L” : TEST mode)
81 VDD — Power supply pin (+5 V)
82 – 85 TSTOUT0 – 3 O TEST key output pin of 4 × 8 matrix. (Not used in this set.)
86 – 93 TSTIN0 – 7 I TEST key input pin of 4 × 8 matrix. (Not used in this set.)
94 TEST/VPP — Fixed at “L” in this set.
95 DCS1 I Disc with/without detection 1 switch (S611) input (“H” : with disc)
96 DCS2 I Disc with/without detection 2 switch (S612) input (“H” : with disc)
97 DCS3 I Disc with/without detection 3 switch (S613) input (“H” : with disc)
98 DCS4 I Disc with/without detection 4 switch (S614) input (“H” : with disc)
99 DCS5 I Disc with/without detection 5 switch (S615) input (“H” : with disc)
100 DCS6 I Disc with/without detection 6 switch (S616) input (“H” : with disc)

– 13 –
4-2. CIRCUIT BOARDS LOCATION

SENSOR board

POWER board

MAIN board

LAMP board SERVO board

– 14 –
 MDX-65

4-3. BLOCK DIAGRAM

IC902
OPTICAL PICK-UP BLOCK 4 IC902
(KMS-241A/J2N) DIGITAL OUT
IC100 IC600 IC601 IC900
DETECTOR RF AMP SYSTEM CONTROL RESET BUS INTERFACE CN900
(BUS CONTROL OUT)
9 F XRST 71 MD RST RESET SYS RST
RESET 15 8 7
SW
6 C SWDT 16 SWDT XLAT 70 MD LAT
F 1 2 3
5 B SCLK 17 SCLK SWDT 41 MD SO UNI CKI 47 11 4 BATT
XLAT 18 XLAT SCLK 42 MD CKO 7 8
B C
I J 2 J RFO 46 IC200 4 5 6
D UNISO 46 9 6
A DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO SIGNAL PROCESSOR BUS CLK
4 A AGCI 40 IC500 UNISI 45 10
E 7 D D/A CONVERTER BUS DATA
RF 38 55 RFI XLAT 7 XLAT IC602
8 E TE 26 74 TE SCLK 6 SCLK LEVEL SHIFT BUS ON
BUS ON 17 13 SW 2
1 I SE 28 73 SE SWDT 5 SWDT
15 RSTB XINT 3 4 21 CC XINT
ADFG 32 78 ADFG XRST 10 XRST
XINT 14 XINT
FE 34 65 FE SRDT 8 SRDT SRDT 1 2 40 MD SI BATTERY DET
BU IN 16
AUTOMATIC Q940, 941
BOTM 36 63 BOTM SQSY 11 SQSY
POWER CONTROL 11 APC CN902-2
PEAK 37 62 PEAK DOUT 22 DOUT SQSY 5 6 18 SQ SY
Q100
LD
R-CH R
DADT 24 5 DATA A ATT 75
DOUT 9 8 MUTING
XBCK 26 6 BCK MUTING Q920
10 PD ABCD 35 64 ABCD MUTING
LRCK 25 4 LRCK CONTROL
MUTE 18 SWITCH AUDIO
PD SWITCH
DMI 17 74 EMPH O Q500 OUT
Q932
VOUTR 9 R-CH
IC930 MUTING
PEAK HOLD VOUTL 12 LINE AMP Q910
75 AUX2
Q200 CN902-1
MNT0 56 MNT0
FS256 27 1 XTI 5 +
IC202 MNT1 57 MNT1 7 L
LASER –
APC SWITCH MNT2 58 MNT2
MNT3 59 MNT3 6
1
APC REF 12 4 83 APC REF SENS 67 SENS
S901
2
(HOME POSITION DET)

8 HOME MDMON 5

RV901 +9V REG.

ELEVATOR HEIGHT 27 EHS +9V
IC603 Q930, 931
SENSOR
LEVEL SHIFT
8 6 88 FFDR S400 Q602 P/U5V
CONTROL
DRIVER

(LIMIT) B+ SWITCH +6V REG.

FOCUS MNT0 1 13 12 MNT0
Q950
11 5 89 FRDR B/U5V
68 LIMIT SW Q970
MNT1 2 11 10 MNT1 B+ SWITCH
S611-616 +5V REG.
29 31 86 TFDR DRV5V
CONTROL

DISC WITH/ Q972

DRIVER

MNT2 3 9 8 MNT2 WITHOUT DET

TRACKING
IC970
26 32 85 TRDR 95 DCS1 REGULATOR CONTROL
MNT3 4 5 6 MNT3 ı
100 DCS6
S620 INPUT 4
22 20 93 SPRD SENS 9 3 4 SENS FRONT DOOR OUT 1
CONTROL

OPEN DET
DRIVER

M901 VCC 2
(SPINDLE)
M
24 19 94 SPFD 69 DOORSW
S902
LOADING END
13 18 91 SRDR SENSOR DET
CONTROL
DRIVER

M902
(SLED)
M IC201 +3.3V
+3V REG.
RAM 6 LES Q800, 801
15 17 92 SFDR
S903
STORE END PL620
LAMP DRIVE
IC300 AO0 32 9 A0 SENSOR DET (ILLUMINATION)
Q600, 601
SLED/SPINDLE MOTOR DRIVE, ı ı
29 12
FOCUS/TRACKING COIL DRIVE · · 7 SES
34 14
ı ı IC700
AO8 38 18 A8 ILL ON 76
ELEVATOR MOTOR DRIVE
Signal Path
D0 47 1 D0
: PB 17 OSCO 9 2 1 M1
CONTROL

· · STR SW 19
DRIVER

X200 46 2 M904
22.5792MHz · · (ELEVATOR)
M S600
48 24 STOP
16 OSCI · · 7 4 2 M1
D4 49 25 D3 X2 10
X600
IC701 14MHz
XOE 41 22 DE
04 LOADING MOTOR DRIVE X1 11
XCAS 42 23 CAS
A09 43 5 A9 9 2 3 M2 XT2 13
CONTROL
DRIVER

XRAS 44 4 RAS M903 X601

XWE 45 3 WE (LOADING)
M 32.768kHz
7 4 4 M2 XT1 14

– 15 – – 16 –
MDX-65

4-4. PRINTED WIRING BOARDS — SERVO SECTION —

THIS NOTE IS COMMON FOR PRINDED WIRING BOARDS
AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)

for schematic diagrams

• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• % : indicates tolerance.
• C : panel designation.
Note: Note:
The components identi- Les composants identifiés par
fied by mark ! or dotted une marque ! sont critiques
line with mark ! are criti- pour la sécurité.
cal for safety. Ne les remplacer que par une
Replace only with part piéce portant le numéro
number specified. spécifié.
• U : B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from Master unit.
• Voltage and waveforms are dc with respect to ground
under no-signal conditions.
no mark : PB
∗ : Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
E : PB
for printed wiring boards
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• r : Through hole.
• b : Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)

Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.

– 17 – – 18 –
 MDX-65

• Semiconductor
Location
Ref. No. Location
D300 C-4

IC100 E-2
IC200 B-4
IC201 A-3
IC202 E-5
IC300 D-4

Q100 F-4
Q200 C-4

(Page 27)

– 19 – – 20 –
MDX-65

4-5. SCHEMATIC DIAGRAM — SERVO SECTION — • Refer to page 33 for Waveforms and page 35 for IC Block Diagrams.

(Page 23)
– 21 – – 22 –
 MDX-65

4-6. SCHEMATIC DIAGRAM — MAIN SECTION — • Refer to page 34 for Waveforms and page 37 for IC Block Diagrams.

(Page 22)

(Page 32)
– 23 – – 24 –
MDX-65

4-7. PRINTED WIRING BOARDS — MAIN SECTION —

• Semiconductor
Location
Ref. No. Location
D500 C-3
D501 C-3
D600 C-2
D601 B-2
D602 E-2
D800 A-3
D801 A-4

IC500 B-3
IC600 D-2
IC601 C-2
IC602 D-4
IC603 D-4
IC700 C-1
IC701 B-2

Q500 C-3
Q600 E-3
Q601 E-3
Q602 B-2
Q800 B-3
Q801 A-3
( ) : SIDE B

– 25 – – 26 –
 MDX-65

(Page 30)

(Page 20)

– 27 – – 28 –
MDX-65

4-8. PRINTED WIRING BOARD — POWER BOARD —

• Semiconductor
Location
Ref. No. Location
D900 B-2
D901 B-2
D902 A-2 (Page 27)
D903 A-2
D904 A-2
D905 A-2
D930 D-4
D940 E-6
D941 E-7
D950 E-5
D951 E-4
D952 E-3
D970 D-9

IC900 B-3
(IC902) E-1
IC930 C-4
IC970 E-7

Q910 C-2
Q920 C-2
Q930 D-5
Q931 D-3
Q932 B-3
Q940 E-6
Q941 E-6
Q950 E-3
Q970 E-4
Q972 D-8
( ) : SIDE B

– 29 – – 30 –
 MDX-65

4-9. SCHEMATIC DIAGRAM — POWER SECTION — • Refer to page 37 for IC Block Diagrams.

(Page 24)

– 31 – – 32 –
• Waveforms

– Servo Section – – Main Section –

1 IC100 4 (A) PLAY MODE 5 IC100 #• (RF) PLAY MODE 9 IC200 @§ (XBCK) 1 IC600 !º (X2) 5 IC500 1 (XT1)
200 mV/DIV, 10 µsec/DIV 500 mV/DIV, 1 µsec/DIV

3.2 Vp-p 2.7 Vp-p 3.2 Vp-p

Approx.
Approx. 1.1 Vp-p
150 mVp-p

354 ns 71 ns 89 ns

2 IC100 8 (E) PLAY MODE 6 IC100 #¢, IC200 ^∞ (FE) PLAY MODE !º IC200 !§ (OSCI) 2 IC600 !¢ (XT1)
100 mV/DIV, 10 µsec/DIV 200 mV/DIV, 0.5 msec/DIV

2.8 Vp-p 2.6 Vp-p

Approx. 400 mVp-p
150 mVp-p

44.3 ns 30.4 µs

3 IC100 9 (F) PLAY MODE 7 IC100 @§, IC200 &¢ (TE) PLAY MODE 3 IC500 4 (LRCK)
100 mV/DIV, 10 µsec/DIV 500 mV/DIV, 0.5 msec/DIV

2.8 Vp-p
Approx. 2.0 Vp-p
150 mVp-p

22.7 µs

4 IC100 1, 2 (I, J) PLAY MODE 8 IC200 @∞ (LRCK) 4 IC500 6 (BCK)

100 mV/DIV, 10 µsec/DIV

3.2 Vp-p 2.8 Vp-p

150 mVp-p

22.7 µs 354 ns

– 33 – – 34 –
• IC Block Diagrams

– Servo Section –

IC100 CXA2523AR

COMPO
COMPP
MORFO

RF AGC
MORFI

ADDC

PEAK
AGCI
OPN

OPO
RFO

RF
48 47 46 45 44 43 42 41 40 39 38 37
USROP
–
+ RF AGC EQ
+
– USRC
RFA1
DET EQ
+
–

BPF3T
RFA2 RFA3 AUX
I 1 –1 HLPT PEAK3T
–1 3T SW
– P-P
–2
J 2 – –2

OFST 3T WBL
PTGR TEMP
– PEAK
1
– –2
CVB + –2 BOTTOM 36 BOTM
–1 PBH
VC 3 – GRV
GRVA PBSW WBL
35 ABCD
34 FE
+ –
A 4 – 33 AUX
– AA –
IVR – ABCDA BPFC

32 ADFG

B 5 + 31 ADAGC
IVR – BB +
+ 30 ADIN
–
– FEA

C 6 +
IVR – CC DET
BPF22
–
– ADIP
+ WBL 29 ADFM
AGC
D 7 + + ATA
IVR – DD
WBL
–1 TG
28 SE
– PTGR –2
E 8 + SEA
+ EE' +
IVR – EE – 27 CSLED
– +
EFB TESW –1 TG
26 TE
EBAL –2
TEA
ESW
F 9 +
+
IVR – FF WBL
– FF'
3T VI CONV 25 WBLADJ
IV
GSW FBAL EQ

PD 10 AUXSW
COMMAND BGR
+ –

+ – VREF
SCRI - PARA
APC 11 DECODE
APCREF 12

13 14 15 16 17 18 19 20 21 22 23 24
GND

TEMPI

TEMPR

SWDT

SCLK

XLAT

XSTBY

F0CNT

VREF

EQADJ
3TADJ

VCC

– 35 –
 IC200 CXD2652AR

APCREF

F0CNT
TEST3
TEST2
TEST1

SRDR

DVDD

DCHG
EFMO

SPRD

TRDR
LDDR
DVSS

FRDR
SFDR

ADFG
SPFD

TFDR

DTRF
CKRF
FFDR

XLRF
FGIN

APC
FS4
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76

SEQUENCER
SPINDLE PWM 75 AUX2

AUTO
SERVO GENERATOR 74 TE
MNT0 1
73 SE
MNT1 2 MONITOR EACH
CONTROL BLOCK 72 AVSS
MNT2 3
MNT3 4 71 ADRB
ADIP 70 ADRT
DECODER
69 AVDD
SWDT 5
SCLK 6 68 ADIO

XLAT 7 CPU I/F EACH

67 VC
BLOCK SERVO A/D
SRDT 8 66 AUX1
DSP CONVERTER
SENS 9 ANALOG 65 FE
MUX 64 ABCD
XRST 10
63 BOTM
SQSY 11 SUBCODE 62 PEAK
DQSY 12 PROCESSOR

61 CLTV
RECP 13
60 FILO

PLL
59 FILI

EFM/ACIRC
ENCODER/
DECODER
58 PCO

SHOCK RESISTANT
XINT 14 57 PDO
MEMORY CONTROLLER
TX 15 56 AVSS
OSCI 16
CLOCK EACH
OSCO 17
GENERATOR BLOCK
XTSL 18 55 RFI
COMP
NC 19 DIGITAL SAMPLING 54 BIAS
AUDIO RATE
DVSS 20 53 AVDD
I/F CONVERTER
DIN 21 52 ASYI
DOUT 22 51 ASYO

ADDT 23 ATRAC
ENCODER/DECODER
DADT 24

LRCK 25

ADDRESS/DATA BUS A00 - A11, D0 - D3

26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
XBCK
FS256
DVDD

A03
A02
A01
A00
A10
A04
A05
A06
A07
A08
A11
DVSS
XOE
XCAS
A09
XRAS
XWE
D1
D0
D2
D3

MVCI

IC300 MPC17A38ZVMEL
PGND
PGND

PGND
GND

F/R4
RO3

RO4
FO3

FO4
RI3

PI4
FI3
VG

VD

VD

VD
PS
OE

36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19

DC/DC DRIVER DRIVER DRIVER DRIVER

CONVERTER

VC

CLOCK PRE-DRIVER PRE-DRIVER PRE-DRIVER PRE-DRIVER

VC VC VC VC

CLK
DETECTOR CONTROL CONTROL CONTROL CONTROL
VC VC VC VC

VC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
LG

VC
CLK
GND

RI1
FI1
VD
FO1
PGND
PGND

RO1

VD
RO2
PGND

FO2
VD
FI2
RI2

– 36 –
– Main Section –

IC500 PCM1718E-T1 IC700, 701 LB1638MTP-T1

GND 1 10 N.C.
XTI 1 CLK 20 XTO
DGND 2 CONTROL 19 CLKO
VDD 3
INPUT 18 MUTE

CONTROL LOGIC
LRCIN 4 INTERFACE 17 DM1 IN1 2 9 OUT1
MODE
16 DM0
CONTROL
DIN 5 DIGITAL 15 RSTB 8 VS
FILTER 14 FORMAT
BCKIN 6 VCC 3
7 OUT2
NOISE SHAPER IN2 4
ZERO 7

5 LEVEL 5 LEVEL GND 5 6 N.C.

DAC DAC

LOWPASS LOWPASS
FILTER FILTER

D/C R 8 CMOS CMOS 13 D/C L

AMP AMP
VOUTR 9 12 VOUTL
AGND 10 11 VCC

– Power Section –

IC900 BA8272F-E2 IC970 TL5001CPS-E20

DATA OUT
LINK OFF

CLK OUT

DATA IN

FEED BACK
BUS ON

RESET
VCC

INPUT

OUT
VCC
14 13 12 11 10 9 8
4 3 2 1

RESET U.V.L.O
SWITCH DEAD-TIME
REFERENCE COMPARATOR
VOLTAGE
– + +
OSC –
1 2 3 4 5 6 7 ERROR SWITCH
+
'ON'
BUS CLK
VREF
BUS ON OUT

BUS ON IN

GND

BUS DATA

BUS RESET

AMP – AT
S.C.P. 'H'
–
COMPARATOR 1
+
PWM
COMPARATOR
– S.C.P.
+ LATCH
S.C.P.
COMPARATOR 2
5 6 7 8
SCP

DEAD-TIME
CONTROL

RT

GND

– 37 –
 SECTION 5
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by
number in the exploded views are not supplied. Example : mark !or dotted line with mark.
• Items marked “*” are not stocked since KNOB, BALANCE (WHITE) ... (RED) !are critical for safety.

N
N
they are seldom required for routine service. Replace only with part number
Some delay should be anticipated Parts Color Cabinet’s Color specified.
when ordering these items. • Accessories and packing materials and
• -XX and -X mean standardized parts, so hardware (# mark) list are given in Les composants identifiés par une
they may have some difference from the the last of this parts list. marque !sont critiques pour
original one. la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.

5-1. CASE SECTION

10

1 A 7
18
6
3 10

8
5 #1
2
2 4 19 8

#1

20
15
#1
12
13
16 16 #1
21
A
14
11
16 15

17

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-3376-846-1 DOOR(P)ASSY 12 X-3376-847-1 PANEL(REAR)ASSY
2 3-930-744-01 SPACER(DOOR) 13 3-931-697-01 CUSHION(STOPPER)
3 3-831-441-11 CUSHION, RA TTLEABSORBER * 14 A-3294-566-A POWERBOARD,COMPLETE(US,Canadian,E)
4 X-3376-863-1 DOOR(S)ASSY * 14 A-3294-668-A PO WERBO ARD ,COMPLETE(AEP ,UK)
5 X-3376-845-1 PANEL(FR ONT)ASSY 15 3-930-176-01 DAMPER(798)

* 6 1-672-198-11 LAMPBOARD 16 3-930-177-01 SPRING(FL),TENSION

7 3-909-607-01 SCREW * 17 3-031-482-11 CASE(LOWER)
8 3-348-750-01 CUSHION(DAMPER) 18 3-025-283-01 SHEET(DOORS1)
* 9 3-031-481-11 CASE(UPPER) 19 3-025-284-01 SHEET(DOORS2)
10 3-912-956-11 SCREW (2.6X6) (CU), +BVTT * 20 3-031-503-01 BRACKET

* 11 3-031-489-01 PLA TE, GR OUND * 21 3-031-483-11 COVER

– 38 –
5-2. MAIN BOARD SECTION

58

56 59

57
54

56

55

56
57
MG-798K-133

63

60
53 56

61

52

51
62

64

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 51 3-931-149-02 SHEET(MAINPCBOARD) 58 3-931-699-01 CUSHION(ROLLH)
* 52 A-3294-565-A MAINBOARD,COMPLETE(US,Canadian,E) * 59 3-931-025-11 SHEET(MECHANISMDECK)
* 52 A-3294-667-A MAINBO ARD ,COMPLETE(AEP ,UK) 60 3-931-698-01 CUSHION(ROLLL)
53 1-776-474-11 CABLE, FLA T7P 61 1-668-438-11 MAINFLEXIBLEBOARD
54 3-909-412-01 SCREW (+P) (1.7X2) (TYPE 3) 62 3-880-990-00 SCREW (1.7X3), FLA T,(+) SPECIAL

55 A-3317-382-A SENSORBOARD,COMPLETE * 63 4-952-141-01 CUSHION(SPEAKER)

56 3-348-750-01 CUSHION(DAMPER) * 64 3-021-073-01 CUSHION(MAIN)
* 57 3-715-973-01 CUSHION

– 39 –
5-3. MD SECTION (1)
(MG-798K-133)

102 103
104

101

106
109
109
101 105
101

118

#4
112
113
108
107 S903 S902
#4 109
109

#2 110 111 114

#2
117
M903 #2
#2
116
#3 115
#2 112
M904 112

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 3-317-552-71 SCREW (M1.7) 112 3-377-719-11 WASHER, POL YETHYLENE
102 3-930-314-01 ESCUTCHEON 113 3-930-317-01 GEAR(LD)
103 3-930-319-01 BUTTON(STOP) * 114 X-3374-670-1 CHASSIS(BOTTOM)ASSY
* 104 3-930-320-01 CHASSIS(FRONT) 115 3-930-313-01 GEAR(EL VC)
105 3-931-366-01 STOPPER,LEAD 116 3-020-386-01 GEAR(EL VA2)

106 1-668-264-11 SERVOFLEXIBLEBOARD 117 3-020-363-01 WHEEL(EL V2), WORM

* 107 X-3374-669-1 CHASSIS(MOTOR)ASSY * 118 3-741-875-01 SHEET ,RUBBER
108 3-930-310-01 COLLAR(EHS) M903 X-3371-508-2 MO TORASSY ,LD(LO ADING)
109 3-930-312-02 BEARING(EL V) M904 X-3374-812-1 MOTORASSY ,EL V(ELEV ATOR)
110 X-3374-673-1 BRACKET(LD2)ASSY S902 1-570-771-11 SWITCH(LOADINGENDSENSORDET)

111 3-930-365-01 WHEEL(LD),WORM S903 1-570-771-21 SWITCH(STOREENDSENSORDET)

– 40 –
5-4. MD SECTION (2)
(MG-798K-133)

#2

151

152

160
153 164

154
155
165
156
157 166
163
167
158
162 168
159 161

160 169

170

162

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 151 X-3371-209-3 CHASSIS(TOP)ASSY 161 3-930-350-01 SPRING(EJ),TORSION
* 152 3-020-388-01 GUIDE(HOLDER2) 162 X-3371-216-1 HOLDER(CADDIE)ASSY
153 3-930-318-01 BUTTON (EJECT) ( 61) 163 3-930-352-01 SPRING(DLOCK),TENSION
154 3-930-318-11 BUTTON (EJECT) ( 62) 164 X-3375-509-1 SLIDER(3)ASSY ,LO ADING
155 3-930-318-21 BUTTON (EJECT) ( 63) 165 3-930-366-01 RACK(LOADING)

156 3-930-318-31 BUTTON (EJECT) ( 64) 166 3-930-360-01 SPRING(LIMITER),TORSION

157 3-930-318-41 BUTTON (EJECT) ( 65) 167 X-3374-671-1 CHASSIS(REAR2)ASSY
158 3-930-318-51 BUTTON (EJECT) ( 66) 168 3-930-349-01 SPRING(LOCK),TORSION
159 3-930-354-01 LEVER,DISCEJECT 169 X-3371-219-5 PLA TE(HOLDER)ASSY ,LOCK
160 3-377-719-11 WASHER, POL YETHYLENE 170 3-021-511-01 WASHER

– 41 –
5-5. MD SECTION (3)
(MG-798K-133) #6

#6
209
#6
210
207
207 226
206
206
208 205
205

211
212
203
RV901 213

#6
#2 225
M902
S901 M901
204 203
#4 214 215

224

220 217
#6 218
219 216 #7
201 #5

202

222
221
#5

201
223
The components identified by Les composants identifiés par une
mark !or dotted line with mark. marque !sont critiques pour la
!are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une piéce
specified. portant le numéro spécifié.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 3-930-338-01 HOLDER(OPGUIDEB) 217 X-3371-213-1 HOLDER(SLA)ASSY
202 3-930-332-01 GUIDE(OPB) 218 X-3371-214-1 SCREW(SL)ASSY ,FEED
203 X-3371-212-1 SCREW(EL V)ASSY ,FEED 219 3-930-331-01 GUIDE(OP A)
204 1-658-880-11 EHSFLEXIBLEBOARD 220 3-020-346-01 SPRING(SLOUT2),FEED
205 3-020-351-01 SLEEVE(EL V2) ! 221 8-583-037-02 PICK-UP ,OPTICALKMS-241A/J2N

206 3-930-334-01 SPRING(EL V), COMPRESSION * 222 A-3294-337-A SERVOBOARD,COMPLETE

207 3-930-345-01 PLA TE (B), EL V LIMITER 223 3-932-755-01 SCREW (M1.7X2.2)
* 208 X-3371-215-1 CHASSIS(OP)ASSY 224 3-703-816-32 SCREW(M1.4X1.6),SPECIALHEAD
209 3-930-344-01 PLA TE (A), EL V LIMITER * 225 3-018-070-01 SHEET(TT)
210 3-930-711-01 SPRING(EL V2), COMPRESSION 226 3-930-333-01 SLEEVE(EL V)

211 3-930-339-01 WHEEL(SL),WORM M901 A-3291-507-A MOTORBLOCKASSY ,SP(SPINDLE)

212 3-338-645-31 WASHER (0.8-2.5) M902 A-3291-508-A MOTORBLOCKASSY ,SL(SLED)
213 3-930-343-01 SCREW(K1.7X3.5) RV901 1-223-817-11 RES, VAR, SLIDE 10K (ELEV ATOR HEIGHT
214 3-930-342-01 RET AINER(SP) SENSOR)
215 3-930-336-01 HOLDER(SLB) S901 1-570-771-21 SWITCH(HOMEPOSITIONDET)

216 3-930-335-01 DETENT ,SL

– 42 –
 SECTION 6
ELECTRICAL PARTS LIST LAMP MAIN
NOTE:
• Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by
the parts list may be different from the they are seldom required for routine service. mark !or dotted line with mark.
parts specified in the diagrams or the Some delay should be anticipated !are critical for safety.
components used on the set. when ordering these items. Replace only with part number
• -XX and -X mean standardized parts, so • SEMICONDUCTORS specified.
they may have some difference from the In each case, u : µ, for example:
original one. uA.. : µA.. uPA.. : µPA.. Les composants identifiés par une
• RESISTORS uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. marque !sont critiques pour
All resistors are in ohms. • CAPACITORS la sécurité.
METAL:Metal-film resistor. uF : µF Ne les remplacer que par une piéce
METAL OXIDE: Metal oxide-film resistor. • COILS portant le numéro spécifié.
F:nonflammable uH : µH
• Abbreviation When indicating parts by reference
G : German model number, please include the board.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-672-198-11 LAMPBOARD C604 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
************ C605 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C606 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
<CAP ACIT OR> C607 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C608 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C620 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C609 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
<CONNECTOR> C610 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C611 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
* CN620 1-580-056-21 PIN,CONNECTOR(SMD)3P C650 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C651 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
<PILOTLAMP>
C652 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
PL620 1-517-630-41 LAMP ,PILO T (ILLUMINA TION) C653 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C654 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
<RESISTOR> C699 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C700 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
R620 1-216-298-00 MET ALCHIP 2.2 5% 1/10W
C701 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
<SWITCH> C800 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C801 1-104-852-11 TANT AL. CHIP 22uF 20% 10V
S620 1-692-532-21 SWITCH,PUSH(1KEY)(FRONTDOOROPEN
DET) <CONNECTOR>
*************************************************************
CN500 1-573-370-21 CONNECTOR,FFC/FPC30P
* A-3294-565-A MAINBOARD,COMPLETE(US,Canadian,E) * CN600 1-573-939-11 CONNECTOR,FFC/FPC(ZIF)30P
* A-3294-667-A MAINBO ARD ,COMPLETE(AEP ,UK) CN601 1-573-916-11 CONNECTOR,FFC/FPC(ZIF)7P
********************* * CN602 1-580-055-21 PIN,CONNECTOR(SMD)2P
* CN603 1-580-055-21 PIN,CONNECTOR(SMD)2P
3-034-614-01 PAPER, SHIELD
* CN604 1-580-056-21 PIN,CONNECTOR(SMD)3P
<CAP ACIT OR> CN700 1-580-055-21 PIN,CONNECTOR(SMD)2P
* CN701 1-580-055-21 PIN,CONNECTOR(SMD)2P
C500 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C501 1-104-851-11 TANT AL. CHIP 10uF 20% 10V <DIODE>
C502 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C503 1-115-416-11 CERAMICCHIP 1000PF 5% 25V D500 8-719-988-61 DIODE 1SS355TE-17
C504 1-115-416-11 CERAMICCHIP 1000PF 5% 25V D501 8-719-988-61 DIODE 1SS355TE-17
D600 8-719-977-03 DIODE DTZ5.6B
C505 1-104-851-11 TANT AL. CHIP 10uF 20% 10V D601 8-719-977-03 DIODE DTZ5.6B
C507 1-110-450-11 ELECTCHIP 100uF 20% 6.3V D602 8-719-977-03 DIODE DTZ5.6B
C509 1-104-851-11 TANT AL. CHIP 10uF 20% 10V
C510 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V D800 8-719-421-18 DIODE MA8033-L-TX
C520 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V D801 8-719-988-61 DIODE 1SS355TE-17

C530 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V < IC >

C540 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C541 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V IC500 8-759-571-84 IC PCM1718E/2K
C600 1-104-852-11 TANT AL. CHIP 22uF 20% 10V IC600 8-759-537-17 IC uPD784216GC-038-8EU
C601 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V IC601 8-759-503-60 IC S-80740AN-D4-S
IC602 8-759-238-47 IC TC74HCT7007AF(EL)
C602 1-162-917-11 CERAMICCHIP 15PF 5% 50V IC603 8-759-238-47 IC TC74HCT7007AF(EL)
C603 1-162-917-11 CERAMICCHIP 15PF 5% 50V

– 43 –
 MAIN POWER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
IC700 8-759-823-87 IC LB1638M <NETWORKRESISTOR>
IC701 8-759-823-87 IC LB1638M
RB601 1-233-412-11 RES,CHIPNETWORK 1.0K (3216)
<RESISTOR> RB602 1-233-810-21 RES,CHIPNETWORK 100K (3216)
RB603 1-233-412-11 RES,CHIPNETWORK 1.0K (3216)
JC501 1-216-821-11 MET ALCHIP 1K 5% 1/16W RB605 1-233-412-11 RES,CHIPNETWORK 1.0K (3216)
RB606 1-233-810-21 RES,CHIPNETWORK 100K (3216)
<COIL>
RB607 1-233-412-11 RES,CHIPNETWORK 1.0K (3216)
L600 1-412-058-11 INDUCTORCHIP 10uH RB608 1-239-446-11 RES,CHIPNETWORK 330K (3216)
RB609 1-233-412-11 RES,CHIPNETWORK 1.0K (3216)
<TRANSISTOR>
<SWITCH>
Q500 8-729-424-12 TRANSISTOR UN2112
Q600 8-729-904-60 TRANSISTOR DTB113ZK S600 1-571-914-21 SWITCH,KEYBOARD(STOP)
Q601 8-729-421-22 TRANSISTOR UN2211
Q602 8-729-020-67 TRANSISTOR XN1A312-TX <THERMISTOR>
Q800 8-729-106-60 TRANSISTOR 2SB1115A
TH600 1-810-421-11 THERMISTOR NTH5G36B103K01TE
Q801 8-729-230-49 TRANSISTOR 2SC2712-YG
< VIBRA TOR>
<RESISTOR>
X600 1-760-607-11 VIBRA TOR, CERAMIC(14MHz)
R500 1-216-841-11 MET ALCHIP 47K 5% 1/16W X601 1-579-886-21 VIBRA TOR, CR YST AL(32.768kHz)
R501 1-216-821-11 MET ALCHIP 1K 5% 1/16W *************************************************************
R502 1-216-821-11 MET ALCHIP 1K 5% 1/16W
R503 1-216-801-11 MET ALCHIP 22 5% 1/16W * A-3294-566-A POWERBOARD,COMPLETE(US,Canadian,E)
R505 1-216-801-11 MET ALCHIP 22 5% 1/16W * A-3294-668-A PO WERBO ARD ,COMPLETE(AEP ,UK)
***********************
R509 1-216-829-11 MET ALCHIP 4.7K 5% 1/16W
R540 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W * 3-031-503-01 BRACKET
R541 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W
R542 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W <CAP ACIT OR>
R600 1-216-821-11 MET ALCHIP 1K 5% 1/16W
C900 1-126-204-11 ELECTCHIP 47uF 20% 16V
R601 1-216-833-11 MET ALCHIP 10K 5% 1/16W C901 1-163-275-11 CERAMICCHIP 0.001uF 5% 50V
R602 1-216-841-11 MET ALCHIP 47K 5% 1/16W C902 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V
R603 1-216-821-11 MET ALCHIP 1K 5% 1/16W C903 1-163-017-00 CERAMICCHIP 0.0047uF 5% 50V
R604 1-216-821-11 MET ALCHIP 1K 5% 1/16W C904 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V
R605 1-216-821-11 MET ALCHIP 1K 5% 1/16W
C905 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V
R606 1-216-837-11 MET ALCHIP 22K 5% 1/16W C910 1-126-603-11 ELECTCHIP 4.7uF 20% 35V
R608 1-218-708-11 MET ALCHIP 4.7K 0.50% 1/16W C911 1-162-569-11 CERAMICCHIP 100PF 2% 50V
R609 1-216-821-11 MET ALCHIP 1K 5% 1/16W C912 1-126-193-11 ELECT 1uF 20% 50V
R610 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W C913 1-126-603-11 ELECTCHIP 4.7uF 20% 35V
R611 1-216-829-11 MET ALCHIP 4.7K 5% 1/16W
C920 1-126-603-11 ELECTCHIP 4.7uF 20% 35V
R612 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W C921 1-162-569-11 CERAMICCHIP 100PF 2% 50V
R613 1-216-829-11 MET ALCHIP 4.7K 5% 1/16W C922 1-126-193-11 ELECT 1uF 20% 50V
R614 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W C923 1-126-603-11 ELECTCHIP 4.7uF 20% 35V
R615 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W C930 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V
R616 1-216-821-11 MET ALCHIP 1K 5% 1/16W
C933 1-126-204-11 ELECTCHIP 47uF 20% 16V
R617 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W C934 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V
R618 1-216-845-11 MET ALCHIP 100K 5% 1/16W C936 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V
R621 1-216-821-11 MET ALCHIP 1K 5% 1/16W C938 1-128-590-11 ELECTCHIP 100uF 20% 6.3V
R622 1-216-851-11 MET ALCHIP 330K 5% 1/16W C940 1-164-346-11 CERAMICCHIP 1uF 16V
R623 1-216-821-11 MET ALCHIP 1K 5% 1/16W
C950 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V
R624 1-216-851-11 MET ALCHIP 330K 5% 1/16W C951 1-125-710-11 DOUBLELA YERS 0.1F 5.5V
R800 1-216-815-11 MET ALCHIP 330 5% 1/16W C952 1-124-779-00 ELECTCHIP 10uF 20% 16V
R801 1-216-829-11 MET ALCHIP 4.7K 5% 1/16W C970 1-163-133-00 CERAMICCHIP 470PF 5% 50V
R802 1-216-815-11 MET ALCHIP 330 5% 1/16W C971 1-163-986-00 CERAMICCHIP 0.027uF 10% 25V

– 44 –
 POWER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C973 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V <TRANSISTOR>
C974 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V
C975 1-126-204-11 ELECTCHIP 47uF 20% 16V Q910 8-729-920-21 TRANSISTOR DTC314TKH04
C976 1-128-590-11 ELECTCHIP 100uF 20% 6.3V Q920 8-729-920-21 TRANSISTOR DTC314TKH04
C977 1-128-590-11 ELECTCHIP 100uF 20% 6.3V Q930 8-729-424-59 TRANSISTOR UN2212
Q931 8-729-920-85 TRANSISTOR 2SD1664-QR
C978 1-128-590-11 ELECTCHIP 100uF 20% 6.3V Q932 8-729-424-12 TRANSISTOR UN2112
C980 1-128-590-11 ELECTCHIP 100uF 20% 6.3V
C981 1-127-485-00 ELECT 33uF 20% 6.3V Q940 8-729-230-49 TRANSISTOR 2SC2712-YG
C983 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V Q941 8-729-901-06 TRANSIST OR DT A144EK
C984 1-164-004-11 CERAMICCHIP 0.1uF 10% 25V Q950 8-729-920-85 TRANSISTOR 2SD1664-QR
Q970 8-729-106-60 TRANSISTOR 2SB1115A
<CONNECTOR> Q972 8-729-822-84 TRANSIST OR 2SB1202F AST

CN900 1-580-907-12 PLUG,CONNECTOR(BUSCONTROLOUT) <RESISTOR>

* CN901 1-573-939-11 CONNECTOR,FFC/FPC(ZIF)30P
R900 1-216-089-00 RES,CHIP 47K 5% 1/10W
<JACK> R901 1-216-071-00 MET ALCHIP 8.2K 5% 1/10W
R910 1-216-079-00 MET ALCHIP 18K 5% 1/10W
CN902 1-580-441-11 JACK,PIN2P(AUDIOOUT) R911 1-216-097-00 RES,CHIP 100K 5% 1/10W
R912 1-216-081-00 MET ALCHIP 22K 5% 1/10W
<DIODE>
R913 1-216-081-00 MET ALCHIP 22K 5% 1/10W
D900 8-719-421-27 DIODE MA728 R914 1-216-033-00 MET ALCHIP 220 5% 1/10W
D901 8-719-057-80 DIODE MA8160-M-TX R915 1-216-097-00 RES,CHIP 100K 5% 1/10W
D902 8-719-421-27 DIODE MA728 R920 1-216-079-00 MET ALCHIP 18K 5% 1/10W
D903 8-719-057-80 DIODE MA8160-M-TX R921 1-216-097-00 RES,CHIP 100K 5% 1/10W
D904 8-719-421-27 DIODE MA728
R922 1-216-081-00 MET ALCHIP 22K 5% 1/10W
D905 8-719-057-80 DIODE MA8160-M-TX R923 1-216-081-00 MET ALCHIP 22K 5% 1/10W
D930 8-719-422-97 DIODE MA8091-M R924 1-216-033-00 MET ALCHIP 220 5% 1/10W
D940 8-719-977-12 DIODE DTZ6.8B R925 1-216-097-00 RES,CHIP 100K 5% 1/10W
D941 8-719-988-61 DIODE 1SS355TE-17 R930 1-216-049-11 RES,CHIP 1K 5% 1/10W
D950 8-719-988-61 DIODE 1SS355TE-17
R931 1-216-057-00 MET ALCHIP 2.2K 5% 1/10W
D951 8-719-422-62 DIODE MA8062-L-TX R932 1-216-057-00 MET ALCHIP 2.2K 5% 1/10W
D952 8-719-041-79 DIODE MA721W A-TX R933 1-216-009-00 RES,CHIP 22 5% 1/10W
D970 8-719-210-43 DIODE EC10QS-06 R940 1-216-097-00 RES,CHIP 100K 5% 1/10W
R941 1-216-093-00 RES,CHIP 68K 5% 1/10W
<JUMPERRESISTOR>
R942 1-216-109-00 MET ALCHIP 330K 5% 1/10W
FB903 1-216-295-00 SHOR T 0 R943 1-216-089-00 RES,CHIP 47K 5% 1/10W
R950 1-216-049-11 RES,CHIP 1K 5% 1/10W
< IC > R951 1-216-085-00 RES,CHIP 33K 5% 1/10W
R970 1-216-214-00 RES,CHIP 4.7K 5% 1/8W
IC900 8-759-444-86 IC BA8272F-E2
IC902 8-749-923-53 IC TOTX193 (DIGIT AL OUT) R971 1-216-206-00 RES,CHIP 2.2K 5% 1/8W
IC930 8-759-711-82 IC NJM4580E R972 1-216-206-00 RES,CHIP 2.2K 5% 1/8W
IC970 8-759-983-96 IC TL5001CPS R973 1-216-061-00 MET ALCHIP 3.3K 5% 1/10W
R974 1-216-081-00 MET ALCHIP 22K 5% 1/10W
<COIL> R975 1-216-077-00 MET ALCHIP 15K 5% 1/10W

L970 1-409-640-21 INDUCTOR 10uH R976 1-216-174-00 RES,CHIP 100 5% 1/8W

L971 1-403-584-11 INDUCTOR 33uH R977 1-216-198-00 RES,CHIP 1K 5% 1/8W
L972 1-409-640-21 INDUCTOR 10uH R978 1-216-198-00 RES,CHIP 1K 5% 1/8W
R979 1-216-663-11 MET ALCHIP 3.3K 0.5% 1/10W
<FIL TER> R980 1-216-649-11 MET ALCHIP 820 0.5% 1/10W

NF900 1-239-466-21 FIL TER, EMI R981 1-216-158-00 RES,CHIP 22 5% 1/8W

<FUSE> <SWITCH>

PC1 1-533-351-11 FUSE, CHIP (2A/125V) SW1 1-572-552-11 SWITCH, SLIDE(ANALOG/DIGIT AL)
*************************************************************

– 45 –
 SENSOR SERVO
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-3317-382-ASENSORBOARD,COMPLETE <CONNECTOR>
************************
WhenreplacinganypartsintheSENSORboard, CN100 1-573-929-11 CONNECTOR,FFC/FPC(ZIF)20P
thewholemountedboardshouldbereplaced. CN200 1-573-370-21 CONNECTOR,FFC/FPC30P
************************************************************* * CN300 1-770-619-11 PIN,CONNECTOR2P
CN400 1-573-346-21 CONNECTOR,FFC/FPC6P
* A-3294-337-A SERVOBOARD,COMPLETE
*********************** <DIODE>

<CAP ACIT OR> D300 8-719-988-61 DIODE 1SS355TE-17

C100 1-107-685-11 TANT AL. CHIP 15uF 20% 6.3V <FERRITEBEAD>

C101 1-135-201-11 TANT ALUMCHIP 10uF 20% 4V
C102 1-135-201-11 TANT ALUMCHIP 10uF 20% 4V FB200 1-414-594-11 INDUCTOR,FERRITEBEAD
C103 1-162-964-11 CERAMICCHIP 0.001uF 10% 50V
C104 1-162-969-11 CERAMICCHIP 0.0068uF 10% 25V < IC >

C105 1-164-227-11 CERAMICCHIP 0.022uF 10% 25V IC100 8-752-080-95 IC CXA2523AR

C106 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V IC200 8-752-384-47 IC CXD2652AR
C107 1-110-563-11 CERAMICCHIP 0.068uF 10% 16V IC201 8-759-498-44 IC MSM51V4400-70TS-K
C108 1-162-968-11 CERAMICCHIP 0.0047uF 10% 50V IC202 8-759-058-62 IC TC7S08FU(TE85R)
C109 1-109-982-11 CERAMICCHIP 1uF 10% 10V IC300 8-759-442-80 IC MPC17A38ZVMEL

C110 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V <COIL>

C111 1-164-227-11 CERAMICCHIP 0.022uF 10% 25V
C112 1-162-970-11 CERAMICCHIP 0.01uF 10% 25V L100 1-412-058-11 INDUCTORCHIP 10uH
C113 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V L200 1-412-058-11 INDUCTORCHIP 10uH
C200 1-107-685-11 TANT AL. CHIP 15uF 20% 6.3V L300 1-412-034-11 INDUCTORCHIP 330uH

C202 1-162-919-11 CERAMICCHIP 22PF 5% 50V <TRANSISTOR>

C203 1-162-919-11 CERAMICCHIP 22PF 5% 50V
C204 1-164-217-11 CERAMICCHIP 150PF 5% 50V Q100 8-729-216-22 TRANSISTOR 2SA1162-G
C206 1-162-970-11 CERAMICCHIP 0.01uF 10% 25V Q200 8-729-230-49 TRANSISTOR 2SC2712-YG
C207 1-107-823-11 CERAMICCHIP 0.47uF 10% 16V
<RESISTOR>
C208 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C209 1-162-927-11 CERAMICCHIP 100PF 5% 50V R100 1-216-853-11 MET ALCHIP 470K 5% 1/16W
C210 1-162-968-11 CERAMICCHIP 0.0047uF 10% 50V R101 1-218-706-11 MET ALCHIP 3.9K 0.50% 1/16W
C211 1-107-823-11 CERAMICCHIP 0.47uF 10% 16V R102 1-216-308-00 MET ALCHIP 4.7 5% 1/10W
C212 1-163-023-00 CERAMICCHIP 0.015uF 5% 50V R103 1-216-811-11 MET ALCHIP 150 5% 1/16W
R104 1-216-853-11 MET ALCHIP 470K 5% 1/16W
C213 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C214 1-109-982-11 CERAMICCHIP 1uF 10% 10V R105 1-218-739-11 RES,CHIP 91K 5% 1/16W
C215 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V R106 1-216-994-11 RES,CHIP 13K 5% 1/16W
C216 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V R107 1-216-994-11 RES,CHIP 13K 5% 1/16W
C217 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V R108 1-216-994-11 RES,CHIP 13K 5% 1/16W
R109 1-216-842-11 MET ALCHIP 56K 5% 1/16W
C218 1-162-927-11 CERAMICCHIP 100PF 5% 50V
C219 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V R110 1-216-833-11 MET ALCHIP 10K 5% 1/16W
C220 1-162-970-11 CERAMICCHIP 0.01uF 10% 25V R111 1-216-833-11 MET ALCHIP 10K 5% 1/16W
C221 1-162-970-11 CERAMICCHIP 0.01uF 10% 25V R204 1-216-809-11 MET ALCHIP 100 5% 1/16W
C300 1-104-852-11 TANT AL. CHIP 22uF 20% 10V R205 1-216-833-11 MET ALCHIP 10K 5% 1/16W
R206 1-216-845-11 MET ALCHIP 100K 5% 1/16W
C301 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C302 1-107-682-11 CERAMICCHIP 1uF 10% 16V R207 1-216-855-11 MET ALCHIP 680K 5% 1/16W
C303 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V R208 1-216-827-11 MET ALCHIP 3.3K 5% 1/16W
C304 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V R209 1-216-821-11 MET ALCHIP 1K 5% 1/16W
C305 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V R210 1-216-821-11 MET ALCHIP 1K 5% 1/16W
R211 1-216-811-11 MET ALCHIP 150 5% 1/16W
C306 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V
C400 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V R212 1-216-819-11 MET ALCHIP 680 5% 1/16W
C401 1-107-826-11 CERAMICCHIP 0.1uF 10% 16V R213 1-216-853-11 MET ALCHIP 470K 5% 1/16W
R214 1-216-809-11 MET ALCHIP 100 5% 1/16W

– 46 –
 SERVO
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R215 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W **************
R216 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W HARD WARELIST
R217 1-216-825-11 MET ALCHIP 2.2K 5% 1/16W **************

<NETWORKRESISTOR> #1 7-685-793-09 SCREW +PTT 2.6X8 (S)

#2 7-627-554-07 SCREW ,PRECISION+P2X2.2
RB200 1-233-576-11 RES,CHIPNETWORK 100 #3 7-627-852-37 SCREW ,PRECISION+P1.7X1.8 TYPE3
RB300 1-233-600-11 RES,CHIPNETWORK 2.2 #4 7-627-855-07 SCREW ,PRECISION+P2X5.5 TYPE3
RB301 1-233-600-11 RES,CHIPNETWORK 2.2 #5 7-627-852-27 +P 1.7X3

<SWITCH> #6 7-627-552-18 SCREW ,PRECISION+P1.7X1.6

#7 7-627-852-58 SCREW ,PRECISION+P1.7X5 TYPE3
S400 1-692-532-21 SWITCH, PUSH (1 KEY) (LIMIT) *************************************************************

< VIBRA TOR> PAR TSFORINST ALLA TIONANDCONNECTIONS

***************************************
X200 1-767-429-21 VIBRA TOR, CR YST AL(22.5792MHz)
************************************************************* 251 3-930-163-21 BASE(FITTING)
252 X-3371-178-1 BRACKETASSY
MISCELLANEOUS 253 3-930-166-01 CUSHION(FITTING)
*************** 254 7-682-961-01 SCREW+PSW4X8
255 4-304-511-00 NUT(M5),FLANGE
53 1-776-474-11 CABLE, FLA T7P
61 1-668-438-11 MAINFLEXIBLEBOARD 256 1-590-519-21 CORD(WITHCONNECTOR)(BUSCABLE)(5.5m)
106 1-668-264-11 SERVOFLEXIBLEBOARD 257 1-777-284-11 CORD,CONNECTION(RCAPINCORD)(5.5m)
204 1-658-880-11 EHSFLEXIBLEBOARD
! 221 8-583-037-02 PICK-UP ,OPTICALKMS-241A/J2N
251 252 253
M901 A-3291-507-A MOTORBLOCKASSY ,SP(SPINDLE)
M902 A-3291-508-A MOTORBLOCKASSY ,SL(SLED)
M903 X-3371-508-2 MOTORASSY ,LD(LO ADING)
M904 X-3374-812-1 MOTORASSY ,EL V(ELEV ATOR)
RV901 1-223-817-11 RES, VAR, SLIDE 10K (ELEV ATOR HEIGHT
SENSOR) 254 255 256 257

S901 1-570-771-21 SWITCH(HOMEPOSITIONDET)

S902 1-570-771-11 SWITCH(LOADINGENDSENSORDET)
S903 1-570-771-21 SWITCH(STOREENDSENSORDET)
*************************************************************

ACCESSORIES&P ACKINGMA TERIALS

********************************

3-865-667-11MANU AL, INSTR UCTION, INST ALL(ENGLISH,

FRENCH,SP ANISH,CHINESE)
(US,Canadian,E)
3-865-928-11 MANU AL, INSTR UCTION(ENGLISH,SP ANISH,
SWEDISH,POR TUGUESE)(AEP ,UK)
3-865-928-21 MANUAL,INSTRUCTION(FRENCH,GERMAN,
DUTCH,IT ALIAN)(AEP ,UK)
3-865-928-31 MANUAL,INSTRUCTION(GERMAN,RUSSIAN)(G)
*************************************************************

The components identified by Les composants identifiés par une

mark !or dotted line with mark. marque !sont critiques pour la
!are critical for safety. sécurité.
Replace only with part number Ne les remplacer que par une piéce
specified. portant le numéro spécifié.

– 47 –
MDX-65

Sony Corporation
99A0478-1
9-926-423-11 Personal & Mobile Communication Company Printed in Japan C1999. 1
– 48 – Published by Quality Assurance Dept.