M Icfb200
M Icfb200
SPECIFICATIONS FEATURES
FM/AM RADIO
9-925-744-13 Sony Corporation
2001B0400-1 Audio Entertainment Group
© 2001. 2 General Engineering Dept.
1
HOW TO CHANGE THE CERAMIC FILTERS TABLE OF CONTENTS
This model is used two ceramic filters of CF1 and CF3.
You must use same type of color marked ceramic filters in order to 1. GENERAL
meet same specifications. Power Sources ........................................................................ 3
Therefore, the ceramic filter must change two pieces together since Playing the Radio ................................................................... 3
it’s supply two pieces in one package as a spare parts. Useful functions ..................................................................... 3
6. EXPLODED VIEWS
6-1. Cabinet (Rear) Section ..................................................... 13
6-2. Cabinet (Front) Section .................................................... 14
–2–
SECTION 1
GENERAL This section is extracted
from instruction manual.
–3–
SECTION 2
SERVICE NOTE
• Moisture Resistant Treatment
Be sure to perform the following work when the cabinet,
telescopic antenna and knobs have been replaced in servicing :
cabinet (rear)
cabinet (front) assy
grease applying
points (gear)
grease applying
points
cabinet (front)
grease applying
points
cabinet (front)
–4–
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
3 tapping screws
(bind 2x20)
2 tapping screws
(bind 2x20)
5 generator
4 PTP 3x10
3 PTP 3x10
8 screw (M1.7)
!¡ MAIN board assy
7 JACK board
9 VOLUME board
!º holder (VOL)
6 claws
2 knob (VOL)
Note for installation :
When installing the MAIN board assy,
align the two slide switches with the levers.
1 knob (TUNING)
–5–
3-3. MAIN BOARD
7 MAIN board
8 LED board
3 gear (midway)
5 lamp
1 retainer
2 tuning shaft
6 claws
4 dial scale
2 gear (midway)
rack Note : Align part A with the
gear (VC) concave of the gear (VC).
4 retainer
3 tuning shaft
–6–
SECTION 4 SECTION 5
ELECTRICAL ADJUSTMENTS DIAGRAMS
AM AM IF ADJUSTMENT • IC Block Diagrams
AM RF signal Adjust for a maximum reading on level meter.
generator
T1
Put the lead-wire 455 kHz IC1 CXA1019S
antanna close to
the set.
AM FREQUENCY COVERAGE
FM/AM BAND
DET OUT
ADJUSTMENT
AFC AGC
AFC AGC
30 % amplitude
AM IF IN
FM IF IN
SELECT
RIPPLE
AF OUT
METER
IF GND
FILTER
AF IN
modulation by
GND
GND
VCC
N.C
Adjust for a maximum reading on level meter.
400 Hz signal
L3 CT3 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
level meter
(range : 0.5 – 5 V ac) 520 kHz 1,650 kHz
AM IF DET AGC
TUNING
8Ω METER
AM TRACKING ADJUSTMENT
set Adjust for a maximum reading on level meter. AF POWER AMP AM FE FM IF
L1 CT4 FM
speaker terminal 620 kHz 1,400 kHz DISCRIMINATOR
FM FE
FM FM FREQUENCY COVERAGE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
FM RF signal ADJUSTMENT
GND
GND
FM DISCRI
NF
VOL
AM OSC
AFC
FM OSC
REG OUT
FM RF
AM RF IN
FE GND
FM RF IN
N.C
FM/AM
IF OUT
generator
Adjust for a maximum reading on level meter.
L4 CT1
0.01 µF 86.5 MHz 109.5 MHz
to FM antenna IC3 BA10324AF
terminal
FM TRACKING ADJUSTMENT
22.5 kHz frequency deviation
OUT4
OUT3
–IN4
+IN4
+IN3
–IN3
by 400 Hz signal
GND
Adjust for a maximum reading on level meter.
output level : as low as possible L2 CT2 13 12 11 10 9
14 8
8Ω
set 1 2 3 4 5 6 7
OUT1
–IN1
+IN1
VCC
+IN2
–IN2
OUT2
speaker terminal
AM
TRACKING L1
ADJUSTMENT CT4
L3 CT3
AM FREQUENCY
COVERAGE
ADJUSTMENT
L4 CT1
FM FREQUENCY
COVERAGE
ADJUSTMENT
T1
L2 CT2
AM IF
ADJUSTMENT FM
TRACKING
ADJUSTMENT
–7– –8–
ICF-B200
• Semiconductor
Location
Ref. No. Location
D1 H-4
D2 F-7
D3 F-9
D4 F-8
D5 F-7
D6 E-9
D7 F-8
D8 F-7
D9 F-8
D11 B-5
IC1 F-5
IC2 D-9
IC3 E-8
Q1 F-11
Q2 G-4
Q3 H-4
Q4 C-8
Q5 D-8
Q6 D-8
Q7 E-6
Q8 E-7
Q11 E-7
Q12 H-3
Q13 E-3
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• W : indicates side identified with part number.
• ¢ : internal component.
• b : Pattern from the side which enables seeing.
–9– – 10 –
ICF-B200
TOTAL CURRENT
FM : 6.0mA
AM : 4.5mA
BUZZER ON : 30mA
LIGHT ON : 60mA
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or • Voltage is dc with respect to ground under no-signal (detuned)
less are not indicated except for electrolytics and tantalums. condition.
• All resistors are in Ω and 1/ 4 W or less unless otherwise specified. no mark : FM
• ¢ : internal component. ( ) : AM
• 2 : nonflammable resistor. < > : BUZZER ON
• C : panel designation. • Voltages are taken with a VOM (Input impedance 10 MΩ).
• U : B+ Line. Voltage variations may be noted due to normal production toler-
• H : adjustment for repair. ances.
• Power voltage is dc 3 V and fed with regulated dc power supply • Signal path.
from battery terminal. F : FM
f : AM
– 11 – – 12 –
Ver 1.3 2001. 02 SECTION 6 Ver 1.3 2001. 02
EXPLODED VIEWS
6-2. CABINET (FRONT) SECTION
NOTE:
• The mechanical parts with no reference • -XX and -X mean standardized parts, so • Accessories and packing materials and
#7
number in the exploded views are not supplied. they may have some difference from the hardware (# mark) list are given in 67
• Items marked “*” are not stocked since
76
original one. the last of this parts list.
L1
they are seldom required for routine service. • Color Indication of Appearance Parts
Some delay should be anticipated Example : A
when ordering these items.
71 80
KNOB, BALANCE (WHITE) ... (RED) #7
R R
LED board
Parts Color Cabinet’s Color
72 #2 73 75
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 61 3-018-881-01 SLIDER, POLYETHYLENE 81 3-023-216-01 PLATE (D), BLIND
2 3-917-353-01 RING (BAND), O 11 3-919-944-01 TERMINAL (+), BATTERY 62 3-018-943-01 SPRING (LIGHT) 83 3-831-441-99 CUSHION, STOPPER
3 3-018-885-01 SPRING, RING * 12 3-020-493-01 SHEET 63 3-018-884-11 SCALE, DIAL 84 3-018-868-01 KNOB (HANDLE)
4 3-898-411-01 PACKING, KNOB 13 3-020-951-01 CUSHION (Ni-Cd) 64 3-018-871-01 RACK 85 3-018-865-01 KNOB (POWER)
5 3-900-151-01 SPRING, RING 14 3-021-019-01 CUSHION (BATTERY CASE LID) 65 3-018-870-01 POINTER 86 3-018-859-01 BUTTON (LIGHT)
* 6 1-667-679-11 CONNECTOR BOARD ANT1 1-501-432-11 ANTENNA, TELESCOPIC
66 3-020-689-01 PIN, PARALLEL D1 8-719-069-94 LED TLSU124 (TUNE)
7 4-356-741-41 SCREW, TAPPING (BIND 2X20) BATT2 1-528-831-21 BATTERY PACK (Ni-Cd) (300mAh/2.4V) 68 3-900-147-01 SHAFT, TUNING L1 1-501-732-12 ANTENNA, FERRITE-ROD (AM)
9 3-018-849-11 CABINET (REAR) (ORANGE) (US,Canadian) 69 3-900-149-01 RETAINER
9 3-018-849-21 CABINET (REAR) (BLUE) BATT2 1-528-831-31 BATTERY PACK (Ni-Cd) (300mAh/2.4V) (AEP) 70 X-3374-974-1 CABINET (FRONT) ASSY (INCLUDING SP1)
10 3-007-833-01 TERMINAL (–), BATTERY (ORANGE)
70 X-3380-348-1 CABINET (FRONT) ASSY (INCLUDING SP1)
(BLUE)
– 13 – – 14 –
SECTION 7 CONNECTOR JACK
ELECTRICAL PARTS LIST LED MAIN
NOTE:
• Due to standardization, replacements in • Items marked “*” are not stocked since When indicating parts by reference
the parts list may be different from the they are seldom required for routine service. number, please include the board.
parts specified in the diagrams or the Some delay should be anticipated
components used on the set. when ordering these items.
• -XX and -X mean standardized parts, so • SEMICONDUCTORS
they may have some difference from the In each case, u : µ, for example:
original one. uA.. : µA.. uPA.. : µPA..
• RESISTORS uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
All resistors are in ohms. • CAPACITORS
METAL:Metal-film resistor. uF : µF
METAL OXIDE: Metal oxide-film resistor. • COILS
F:nonflammable uH : µH
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-667-679-11 CONNECTOR BOARD * A-3679-932-A MAIN BOARD, COMPLETE (INCLUDING
***************** LED BOARD)
*********************
< CONNECTOR >
3-018-873-01 CHASSIS (COMBINED)
CN1 1-564-505-11 PLUG, CONNECTOR 2P 3-314-712-01 SHEET, CHLORIDE VINYL
************************************************************* 3-363-895-01 SCREW (M1.7)
– 15 –
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C42 1-164-346-11 CERAMIC CHIP 1uF 16V < COIL >
C43 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C45 1-163-038-00 CERAMIC CHIP 0.1uF 25V L1 1-501-732-12 ANTENNA, FERRITE-ROD (AM)
C46 1-163-038-00 CERAMIC CHIP 0.1uF 25V L2 1-416-503-11 COIL, AIR-CORE
C47 1-163-038-00 CERAMIC CHIP 0.1uF 25V L3 1-406-028-00 COIL, OSC (AM)
L4 1-416-504-11 COIL, AIR-CORE
C48 1-163-038-00 CERAMIC CHIP 0.1uF 25V L5 1-412-943-11 INDUCTOR 2.2uH
C49 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C51 1-135-201-11 TANTALUM CHIP 10uF 20% 4V L6 1-406-680-11 INDUCTOR 33mH
CF1 1-579-632-51 FILTER, CERAMIC PL1 1-517-710-11 LAMP, PILOT (BACK LIGHT)
CF2 1-577-072-11 FILTER, CERAMIC
CF3 1-579-632-51 FILTER, CERAMIC < TRANSISTOR >
– 16 –
Ver 1.3 2001. 02
MAIN VOLUME
Ref. No. Part No. Description Remark
< SWITCH >
T1 1-404-790-11 TRANSFORMER, IF
*************************************************************
MISCELLANEOUS
***************
3-019-238-01
STRAP (US,Canadian)
3-228-890-01
STRAP (AEP)
3-861-125-12
MANUAL, INSTRUCTION (ENGLISH) (US)
3-861-125-21
MANUAL, INSTRUCTION (ENGLISH,FRENCH)
(Canadian)
3-861-125-31 MANUAL, INSTRUCTION (ENGLISH,FRENCH,
GERMAN,SPANISH) (AEP)
*************************************************************
**************
HARDWARE LIST
**************
@ For the push switch S4 on the MAIN board, check the serial number
for the set before replacing the switch by the appropriate part No.
Serial No. Part No.
39430 and previous 1-771-239-11
39431 and later 1-771-367-11
– 17 –
ICF-B200
Ver 1.3 2001. 02
REVISION HISTORY
– 18 –