Sony CFD-G700CP-G770CP-G-770CPK

CFD-G700CP/G770CP/ G770CPK
SERVICE MANUAL
Ver. 1.0 2007.03
US Model
CFD-G700CP
Canadian Model
CFD-G770CPK
E Model
CFD-G770CP/G770CPK
Australian Model
CFD-G770CPK
Photo : CFD-G770CPK
Model Name Using Similar Mechanism CD Section TAPE Section CD Mechanism Type Optical Pick-up Type Model Name Using Similar Mechanism Tape Transport Mechanism Type
CFD-G505/G555CP/G555CPK KSM-213CDP/C2NP KSS-213C HCD-EC50 H21SB-C05
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US) POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 3.2-ohm loads, both channels driven from 1 000 - 10 000 Hz; rated 3 W per channel-minimum RMS power, with no more than 10 % total harmonic distortion in AC operation. Woofer with 4-ohm loads, driven from 50 - 150 Hz; rated 6 W minimum RMS power, with no more than 10 % total harmonic distortion in AC operation. Other specifications CD player section System Compact disc digital audio system Laser diode properties Emission duration: Continuous Laser output: Less than 44.6 W (Th is output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Number of channels 2 Frequency response 20 - 20 000 Hz +1/2 dB Wow and fl utter Below measurable limit Abbreviation AUS : Australian model CND : Canadian model E41 : AC 230V area in E model E92 MX SP Radio section Frequency range FM: 87.5 - 108 MHz AM: 530 - 1 710 kHz (G700CP: US/G770CPK: CND, MX, E92) AM: 531 - 1 611 kHz (G770CPK: AUS) AM: 531 - 1 611 kHz (9 kHz step)(G770CP) AM: 530 - 1 610 kHz (10 kHz step)(G770CP) Antennas FM: Telescopic antenna AM: Built-in ferrite bar antenna Cassette-corder section Recording system 4-track 2 channel stereo Fast winding time Approx. 150 s (sec.) with Sony cassette C-60 Frequency response TYPE I (normal): 70 - 13 000 Hz General Speaker Full range: 10 cm (4 in.) dia., 3.2 , cone type (2) Woofer: 13 cm (5 1/8 in.) dia., 4 , cone type (1) Tweeter: 2 cm (13/16 in.) dia. (2) Input Built-in audio cable with stereo-mini plug: Minimum input level 245 mV AUDIO IN Jack (stereo minijack): Minimum input level 245 mV MIC MIX (microphone) jack (monaural minijack): Sensitivity 2.5 mV, for low impedance microphone Minimum input level 2.5 mV (G770CPK) Outputs Headphones jack (stereo minijack) For 16 - 68 impedance headphones Power output 4 W + 4 W (at 3.2 , 10% harmonic distortion) Woofer: 12 W (at 4 , 10% harmonic distortion) Power requirements For CD radio cassette-corder: 120 V AC, 60 Hz (G700CP: US/G770CPK: CND, MX, E92) 230 - 240 V AC, 50 Hz (G700CP: SP) 230 V AC, 50 Hz (G700CP: E41/G770CPK: AUS) 12 V DC, 8 R20 (size D) batteries For remote control: 3 V DC, 2 R6 (size AA) batteries Power consumption AC 28 W Continued on next page
: AC 120V area in E model : Mexican model : Singapore model
CD RADIO CASSETTE-CORDER
9-887-620-01
2007C16-1 2007.03
Sony Corporation
Personal Audio Division Published by Sony Techno Create Corporation
CFD-G700CP/G770CP/G770CPK
Battery life For CD radio cassette-corder: FM recording Sony R20P: approx. 6 h Sony alkaline LR20: approx. 18 h Tape playback Sony R20P: approx. 1.5 h Sony alkaline LR20: approx. 6 h CD playback Sony R20P: approx. 1 h Sony alkaline LR20: approx. 4 h Dimensions Approx. 551 247 370 mm (w/h/d) (21 3/4 9 3/4 14 5/8 inches) (incl. projecting parts) Mass Approx. 8.4 kg (18 lb. 9 oz) (incl. batteries) Supplied accessories AC power cord (1) Remote control (1) Design and specifications are subject to change without notice.
Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing Keep the temperature of soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY.
TABLE OF CONTENTS 1. 2. 3.
3-1. 3-2. 3-3. 3-4. 3-5.
SERVICING NOTES ............................................... 4 GENERAL ................................................................... 5 DISASSEMBLY

Disassembly Flow ........................................................... Cabinet (Upper) (1) Section ............................................ Cabinet (Upper) (2) Section ............................................ Cabinet (Front) Section ................................................... LCD Board, AUDIO IN Board, HEADPHONE Board, POWER KEY Board, MICROPHONE Board (CFD-G770CPK), VOLUME KEY Board ...................... Front Panel ...................................................................... LED Board ...................................................................... Speaker (13cm) ................................................................ Speaker (10cm) ................................................................ POWER Board, BATTERY Board, D-LIGHT Board (CFD-G700CP) ................................... WOOFER KEY Board, CD KEY Board ......................... TUNER Board ................................................................. Tape Mechanism Deck .................................................... MAIN Board .................................................................... CD Block Section ............................................................ Optical Pick-up (KSM-213CDP/C2NP) ......................... TC Board ......................................................................... Main Belt, Sub Belt ......................................................... 11 12 12 13
6. 7.
7-1. 7-2. 7-3. 7-4. 7-5. 7-6. 7-7. 7-8. 7-9. 7-10. 7-11. 7-12. 7-13. 7-14.
ELECTRICAL ADJUSTMENTS .......................... 23 DIAGRAMS

28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
3-6. 3-7. 3-8. 3-9. 3-10. 3-11. 3-12. 3-13. 3-14. 3-15. 3-16. 3-17. 3-18.
13 14 14 15 15 16 17 17 18 18 19 19 20 20
Block Diagram TUNER/CD Section ....................... Block Diagram MAIN Section ................................. Printed Wiring Board BD90 Board .......................... Schematic Diagram BD90 Board ............................. Printed Wiring Board TUNER Board ....................... Schematic Diagram TUNER Board ......................... Printed Wiring Board TC Board ............................... Schematic Diagram TC Board ................................. Printed Wiring Board MAIN Board ......................... Printed Wiring Boards AUDIO Section .................... Printed Wiring Boards CONTROL Section ............. Schematic Diagram MAIN (1/3), AUDIO Section .. Schematic Diagram MAIN Section (2/3) ................. Schematic Diagram MAIN (3/3), CONTROL Section .............................. 7-15. Printed Wiring Boards POWER Section .................. 7-16. Schematic Diagram POWER Section ......................
8.
8-1. 8-2. 8-3. 8-4. 8-5. 8-6.
EXPLODED VIEWS
Overall Section ................................................................ Cabinet (Front) Section ................................................... Cabinet (Rear) Section .................................................... Cabinet (Upper) Section-1 ............................................... Cabinet (Upper) Section-2 ............................................... Tape Mechanism Deck Section ....................................... 51 52 53 54 55 56
4. 5.
TEST MODE ............................................................... 21 MECHANICAL ADJUSTMENTS ......................... 23
9.
ELECTRICAL PARTS LIST .................................. 57
CFD-G700CP/G770CP/G770CPK SECTION 1 SERVICING NOTES

SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The limit indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal Parts on Set
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe more than 30 cm away from the objective lens. CHUCK PLATE JIG ON REPAIRING On repairing CD section, playing a disc without the CD lid, use Chuck Plate Jig. Code number of Chuck Plate Jig : X-4918-255-1
0.15 F
1.5 k
AC voltmeter (0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.

LASER DIODE AND FOCUS SEARCH OPERATION CHECK 1. Turn ON the [POWER] button. 2. Open the CD lid. 3. Turn on SW2 with screwdriver, etc. as following figure. 4. Press the u (CD) button. 5. Confirm the laser diode emission while observing the objecting lens. When there is no emission, Auto Power Control circuit or Optical Pick-up is broken. Objective lens moves up and down three times for focus search.
SW2
CFD-G700CP/G770CP/G770CPK SECTION 2 GENERAL

CFD-G700CP (1/2) This section is extracted from instruction manual.
Basic Operations
Notes on MP3 discs
Playing a CD/MP3 disc

1 Press
PUSH OPEN/CLOSE on the unit, and place a disc with the label side up on the CD compartment. To close the CD compartment, press PUSH OPEN/ on the unit. CLOSE
2 Press
on the unit ( on the remote) . The unit plays all the tracks/MP3 files once. When you place MP3 discs, MP3 appears in the display after the unit reads the file information.
Audio CD
When the disc is inserted, the unit reads all the files on that disc. During this time, READING is displayed. If there are many folders or non-MP3 files on the disc, it may take a long time for play to begin or for the next MP3 file to start play. We recommend that you do not save unnecessary folders or files other than MP3 ones in the disc to be used for MP3 listening. A folder that does not include an MP3 file is skipped. Maximum number of files: 255 Maximum number of folders: 150 (including the root folder) Maximum number of folders and files in total: 256 Maximum directory levels: 8 Folder names and file names can be displayed with up to 30 characters including quotation marks. The characters A - Z, 0 - 9, and _ can be displayed on this unit. Other characters are displayed as _. This unit conforms to Version 1.0, 1.1, 2.2, 2.3 and 2.4 of the ID3 tag format. When the file has the ID3 tag information, song title, artist name and album name can be displayed. If the file does not have the ID3 tag information, NO TITLE appears instead of song title, NO ARTIST appears instead of artist name and NO ALBUM appears instead of album name. The ID3 tag information can be displayed with up to 15 characters. When naming, be sure to add the file extension mp3 to the file name. If you put the extension mp3 to a file other than an MP3 file, the unit cannot recognize the file properly and will generate random noise that could damage your speakers. The file name does not correspond to the ID3 tag.
Recording on a tape
Use buttons on the unit for the operation.
1 Press
on the unit to open the tape compartment and insert a blank tape with the side you want to record on facing upward. Use TYPE I (normal) tape only. Close the compartment.
2 Select the program source you want to record.

on the unit To record from the CD player, press and place a CD. To record from the radio, tune in the station you want (see Listening to the radio).
3 Press
on the unit to start recording ( depressed automatically).

Press
is
To Pause recording
on the unit. Press the button again to resume recording. on the unit.
Stop recording
Tips
Listening to the radio

Track number MP3 disc Playing time
1 Press RADIO/BAND AUTO PRESET
on the unit on the remote) repeatedly. (RADIO/BAND Each time you press the button, the indication changes as follows: FM AM
Adjusting the volume or the audio emphasis will not affect the recording level. For the best results, use the AC power as a power source for recording. To erase a recording, proceed as follows: 1 Insert the tape whose recording you want to erase. 2 Make sure that TAPE is displayed. (If TAPE is not displayed, press on the unit or press FUNCTION on the remote until it appears in the display.) 3 Press on the unit.
2 Hold down
MP3 file number After the song title is displayed, the playing time* will appear.
* If the playing time is more than 100 minutes, it appears --:-- in the display. * VOL + (VOLUME + on the remote) unit) have a tactile dot. , and (on the
To Pause playback
Press on the unit ( on the remote) . To resume play, press it again.
TUNE + or until the frequency digits begin to change in the display. The unit automatically scans the radio frequencies and stops when it finds a clear station. If you cannot tune in a station, press TUNE + or repeatedly to change the frequency step by step. When an FM stereo broadcast is received, ST appears.
Tip
If the FM broadcast is noisy, press MODE until Mono appears in the display and the radio will play in monaural.
Before using the unit

To turn on/off the power
Press POWER . . .
Stop playback Go to the next track/MP3 file Go back to the previous track/ MP3 file Select a folder on an MP3 disc Locate a point while listening to the sound Locate a point while observing the display Remove the CD
Tips
. . .
Playing a tape
To adjust the volume

Press VOL +, (VOLUME +, on the remote)
To listen through headphones

Connect the headphones to the (headphones) jack
To select the sound characteristic

Press ROCK, DANCE, SALSA, REGGAETON or FLAT to select the kind of audio emphasis that you want. repeatedly.) (On the remote, press SOUND
+ to go forward and to go backward . (forward) or (backward) while playing and hold it until or you find the point. ( on the remote) (forward) or (backward) in pause and hold it until you or on find the point. ( the remote) PUSH OPEN/CLOSE .
1 Press
on the unit, and insert the tape into the tape compartment with the side you want to play facing upward. Use TYPE I (normal) tape only. Close the compartment. Make sure there is no slack in the tape to avoid damaging the tape or the unit.
To reinforce the bass sound

Press POWER DRIVE WOOFER (WOOFER on to select or on the remote) is more effective. When the the display. WOOFER function works, the ring on the front panel lights up. To return to normal sound, press the button repeatedly until the indication disappears from the display.
Notes
While the sleeping timer is on, the ring does not light, even if the WOOFER function is used. When you use the headphones, the WOOFER function does not work.
Playback starts from the track/MP3 file you last stopped playing (Resume play). During stop, the track/MP3 file number to be played is displayed. To cancel the resume play (to start play from the beginning of the first track/MP3 file), press while the CD is stopped. When you open the CD compartment or turn off the unit, the resume play is also canceled.
2 Press
on the unit. The unit starts playing.

Press
To Pause playback
Note
You cannot locate a specific track if SHUF or PGM is lit in the display. Press , and then press MODE repeatedly until SHUF and PGM disappear from the display.
on the unit. To resume play, press it again. on the unit. or forward) (rewind or fast on the unit.
Stop playback Fast-forward or rewind* Eject the cassette
Example of folder structure and playing order

The playing order of the folders and files is as follows:
Folder MP3 file
on the unit.
to release or
* When the tape is wound to the end, press .
CFD-G700CP (2/2)
Other Operations
Using the display
You can check information about the CD using the display.
Playing tracks/MP3 files in random order (Shuffle Play)

You can play tracks/MP3 files in random order. When playing an MP3 disc, you can also play MP3 files in a selected folder in random order (Folder Shuffle Play).
Presetting radio stations

You can store radio stations into the units memory. You can preset up to 30 radio stations, 20 for FM and 10 for AM in any order.
Connecting optional component

You can enjoy the sound from an optional component such as a portable digital music player through the speakers of this unit. Be sure to turn off the power of each component before making any connections. For details, refer to the instruction manual of the component to be connected.
Checking the information of an audio CD

To check the total track number and playing time of the CD
Press while the CD is stopped, and you can check them in the display.

select the band.
on the unit to
1 Press
. CD appears in the display.
2 Hold down RADIO/BAND AUTO PRESET 3 Press DSPL/ENT
2 Press MODE
on the unit for 2 seconds until AUTO flashes in the display. on the unit. The stations are stored in memory from the lower frequencies to the higher ones.
until SHUF appears in the display. When you select Folder Shuffle Play (MP3 disc only), on the unit until and SHUF press MODE appear in the display. Then press TUNE + or on the unit to select a folder you want. on the unit to start Shuffle Play.
Total track number Total playing time
3 Press
Use
If a station cannot be preset automatically

You need to preset a station with a weak signal manually.
On the remote
instead of . until SHUF

select the band.
on the unit to
Checking the information of an MP3 disc

To check the total folder number and total file number on the CD
To cancel Shuffle Play

Stop playing first. Then press MODE disappears from the display.
Tips
During Shuffle Play, you cannot select the previous track/MP3 file by pressing . The resume function does not work during Shuffle Play.
2 Tune in a station you want. 3 Hold down DSPL/ENT on the unit for 2 seconds
until the preset number flashes in the display.
4 Press PRESET + or 5 Press DSPL/ENT

On the remote
on the unit until the preset number you want for the station flashes in the display.
on the unit. The new station replaces the old one.

To AUDIO IN jack
Total folder number Total file number
Creating your own program (Program

Play)
You can arrange the playing order of up to 15 tracks/MP3 files on a CD.
1 Press RADIO/BAND
appears in the display.
until the band you want

Built-in audio cable with stereo-mini plug audio connecting cable (not supplied) To the line output jack (e.g.,portable digital music player)
To check file information

Press DSPL/ENT on the unit while playing an MP3 disc. The display changes as follows: The current file number and playing time The song title ( ) The artist name ( ) The album name ( )
1 Press
. CD appears in the display. until PGM flashes in the display.
2 Tune in a station you want. 3 Hold down ENTER for 2 seconds until the preset
number flashes in the display.
or
2 Press MODE 3 Press or
4 Press PRESET + or 5 Press ENTER

Tip
until the preset number you want for the station flashes in the display. .
then press DSPL/ENT on the on the remote) for the tracks/MP3 unit (ENTER files you want to program in the order you want. TUNE + or first and then For MP3 files, press or and DSPL/ENT (ENTER press on the remote).
Audio CD (Program Play)
The preset radio stations remain in memory even if you unplug the AC power cord or remove the batteries.
1 Connect the built-in audio cable with stereo-mini

on the unit to the line output jack of the plug portable digital music player or other components*.
Playing preset radio stations

select the band. on the unit to
Playing tracks/MP3 files repeatedly

(Repeat Play)
You can play tracks/MP3 files repeatedly in normal, Shuffle or Program play modes.
Programed track number
2 Turn the unit and the connected component on. 3 Press AUDIO IN on the unit and start playing
sound on the connected component. The sound from the connected component is output from the speakers.
* To connect the unit to a TV or VCR, use an extension cable (not supplied) with a stereo-mini jack on one end (for the built-in audio cable) and two phono plugs on the other end.
Playing order MP3 disc (Program Play) Programed file number
2 Press PRESET + or
stored station.
on the unit to tune in the
1 Press
On the remote
2 Proceed as follows.
To repeat A single track/MP3 file Do this
1 Press RADIO/BAND 2 Press PRESET + or
. to tune in the stored station.
Recording the sound from the connected component
Playing order
until 1 appears. 1 Press REPEAT or to select the track/ 2 Press MP3 file that you want to repeat. on the unit. 3 Press until 1 Press REPEAT on the unit. 2 Press appears.
Falling asleep to music

4 Press
Use on the unit to start Program Play.
1 Insert a blank tape. 2 Press AUDIO IN on the unit to display AUDIO IN. 3 Press on the unit.
Recording starts.
All tracks/ MP3 files on the CD A selected folder (MP3 disc only)
On the remote
instead of . until PGM
1 Play the music source you want. 2 Press SLEEP to display SLEEP. 3 Press SLEEP to select the minutes until the unit
goes off automatically. Each time you press the button, the indication changes as follows: AUTO* 60MIN 30MIN 20MIN 10MIN OFF.
* When you select AUTO, the CD or tape stops playing in 90 minutes at most and the unit goes off automatically. When you are listening to the radio, the radio goes off in 90 minutes.
4 Play the optional component connected to the unit.

Tip
Should the built-in audio cable become damaged, you can use the AUDIO IN jack to connect an optional component to the unit. Use an audio connecting cable (not supplied) with a stereo mini plug on one end (for the AUDIO IN jack ). Make sure the plug on the other end is suited to the jack on the optional component; for example, a stereo-mini plug for a portable digital music player, or two phono plugs for a TV or VCR.
To cancel Program Play

Stop playing first. Then press MODE disappears from the display. Press CLEAR
until appears, 1 Press MODE until and then press REPEAT appears. 2 Select the folder by pressing + or . on the unit. 3 Press Tracks/ 1 Select Shuffle Play (see Playing tracks/ MP3 files MP3 files in random order). until SHUF and in random 2 Press REPEAT appear. order on the unit. 3 Press Files in a 1 Start Folder Shufle Play (see Playing selected tracks/MP3 files in random order). on the unit until , folder in 2 Press REPEAT SHUF and appear. random on the unit. order (MP3 3 Press disc only) Programed 1 Program tracks/MP3 files (see Creating tracks/MP3 your own program). files until and PGM 2 Press REPEAT appear. on the unit. 3 Press
To delete the last track or file of the program

on the remote while the unit is stopped.
Notes
Do not pull forcibly on the built-in audio cable . Doing so may cause the plug to rip off. Connect the built-in audio cable or audio connecting cable (not supplied) securely to prevent any malfunction. It is not possible to listen to two components connected at the same time through the built-in audio cable and the AUDIO IN jack (using an optional audio connecting cable). Connect one component at a time.
To check the order of tracks/MP3 files before play

Press DSPL/ENT on the unit. Every time you press the button, the track number and the playing order appear.
If 4 seconds have passed after you pressed SLEEP , the minutes in the display are entered. When the preset time has passed, the unit goes off automatically.
To change the current program

Press once if the CD is stopped and twice if the CD is playing. The current program will be erased. Then create a new program following the programing procedure.
Tips
If you try to program 16 tracks/MP3 files or more, FULL will appear in the display. You can play the same program again, since the program is saved until you open the CD compartment or turn off the power of the unit. You can record your own program. After you have created the program, insert a blank tape and press on the unit to start recording. The resume function does not work during Program Play.
To cancel the sleep function

Press POWER
Note
When you are playing a tape using this function: If the tape length of one side is longer than the set time, the unit will not go off until the tape reaches the end.
to turn off the power.
D-LIGHT SYNC OUT jack

Use the D-LIGHT SYNC controller to connect to this D-LIGHT SYNC OUT jack . You need to connect the D-LIGHT SYNC controller to the lighting device* (not supplied). The lighting device will react according to control signals transmitted by the D-LIGHT SYNC controller upon receiving music source from the system. For details on the use of D-LIGHT SYNC controller and lighting device, refer to the respective operating instructions supplied with the respective device.
On the remote
Use instead of until . disappears from the display.
To cancel Repeat Play

Press REPEAT
D-LIGHT SYNC controller cord of D-LIGHT SYNC controller (DSL-1)

* Refer to the D-LIGHT SYNC controller operating instruction for the recommended lighting device.
Note
The lighting effect may be different depending on the connected lighting device or the type of music being played back.
CFD-G770CP (1/2)
Basic Operations
Notes on MP3 discs

1 Press
PUSH OPEN/CLOSE on the unit, and place a disc with the label side up on the CD compartment. To close the CD compartment, press PUSH OPEN/ on the unit. CLOSE
2 Press
Audio CD
Recording on a tape
1 Press
on the unit to open the tape compartment and insert a blank tape with the side you want to record on facing upward. Use TYPE I (normal) tape only. Close the compartment. on the unit To record from the CD player, press and place a CD. To record from the radio, tune in the station you want (see Listening to the radio).
3 Press

Press
is
To Pause recording
Stop recording
Tips

on the unit (RADIO/BAND on the remote) repeatedly. Each time you press the button, the indication changes as follows: FM AM
Adjusting the volume or the audio emphasis will not affect the recording level. For the best results, use the AC power as a power source for recording. To erase a recording, proceed as follows: 1 Insert the tape whose recording you want to erase. 2 Make sure that TAPE is displayed. (If TAPE is not displayed, on the unit or press FUNCTION on the remote press until it appears in the display.) 3 Press on the unit.
2 Hold down
To Pause playback
Tip

Press POWER . . .
Tips
. . .
Changing the AM tuning interval

If you need to change the AM tuning interval, do the following:

until AM is displayed.
on the unit



+ to go forward and to go backward . (forward) or (backward) while playing and hold it until or you find the point. ( on the remote) (forward) or (backward) in pause and hold it until you find the point. ( or on the remote) PUSH OPEN/CLOSE .
2 Press DSPL/ENT on the unit for 2 seconds. 3 Press RADIO/BAND AUTO PRESET on the unit for
2 seconds. 9K STEP or 10K STEP flashes.
on the unit to select 9K STEP for 9 kHz interval or 10K STEP for 10 kHz interval.

Press POWER DRIVE WOOFER (WOOFER on to select or on the remote) is more effective. When the the display. WOOFER function works, the ring on the front panel lights up. To return to normal sound, press the button repeatedly until the indication disappears from the display.
Notes
on the unit. After changing the tuning interval, you need to reset your preset AM radio stations.
Playback starts from the track/MP3 file you last stopped playing (Resume play). During stop, the track/MP3 file number to be played is displayed. To cancel the resume play (to start play from the beginning of the while the CD is stopped. When you first track/MP3 file), press open the CD compartment or turn off the unit, the resume play is also canceled.
Playing a tape
1 Press
Note

Folder MP3 file
2 Press

Press on the unit. To resume play, press it again.
To Pause playback
on the unit. or forward) (rewind or fast on the unit.
on the unit.
to release or
CFD-G770CP (2/2)
Other Operations
Using the display





select the band.
on the unit to
1 Press
2 Press MODE
on the unit for 2 seconds until AUTO flashes in the display.
until SHUF appears in the display. When you select Folder Shuffle Play (MP3 disc only), press MODE on the unit until and SHUF appear in the display. Then press TUNE + or on the unit to select a folder you want. on the unit to start Shuffle Play.
on the unit. The stations are stored in memory from the lower frequencies to the higher ones.
3 Press
Use

On the remote

select the band.
on the unit to


Tips

On the remote
on the unit until the preset number you want for the station flashes in the display. on the unit. The new station replaces the old one.
To AUDIO IN jack

Play)
1 Press RADIO/BAND

Built-in audio cable with stereo-mini plug audio connecting cable (not supplied) To the line output jack (e.g.,portable digital music player)

1 Press
or

Tip
then press DSPL/ENT on the on the remote) for the tracks/MP3 unit (ENTER files you want to program in the order you want. For MP3 files, press TUNE + or first and then press or and DSPL/ENT (ENTER on the remote).

plug on the unit to the line output jack of the portable digital music player or other components*.


(Repeat Play)
2 Press PRESET + or
stored station.
1 Press
On the remote
Playing order
1 Press REPEAT until 1 appears. or to select the track/ 2 Press MP3 file that you want to repeat. on the unit. 3 Press 1 Press REPEAT until on the unit. 2 Press appears.
4 Press
Use
on the unit to start Program Play.

Recording starts.
On the remote

Tip
Should the built-in audio cable become damaged, you can use the AUDIO IN jack to connect an optional component to the unit. Use an audio connecting cable (not supplied) with a stereo mini plug on one end (for the AUDIO IN jack ). Make sure the plug on the other end is suited to the jack on the optional component; for example, a stereo-mini plug for a portable digital music player, or two phono plugs for a TV or VCR.

until appears, 1 Press MODE until and then press REPEAT appears. 2 Select the folder by pressing + or . on the unit. 3 Press Tracks/ 1 Select Shuffle Play (see Playing tracks/ MP3 files in random order). MP3 files in random 2 Press REPEAT until SHUF and order appear. on the unit. 3 Press 1 Start Folder Shufle Play (see Playing Files in a tracks/MP3 files in random order). selected on the unit until , folder in 2 Press REPEAT SHUF and appear. random order (MP3 3 Press on the unit. disc only) Programed 1 Program tracks/MP3 files (see Creating your own program). tracks/MP3 files until and PGM 2 Press REPEAT appear. on the unit. 3 Press


Notes

Tips
If you try to program 16 tracks/MP3 files or more, FULL will appear in the display. You can play the same program again, since the program is saved until you open the CD compartment or turn off the power of the unit. You can record your own program. After you have created the on the unit to start program, insert a blank tape and press recording. The resume function does not work during Program Play.

Press POWER
Note
On the remote

Press REPEAT
CFD-G770CPK (1/2)
Basic Operations
Notes on MP3 discs

1 Press
PUSH OPEN/CLOSE on the unit, and place a disc with the label side up on the CD compartment. To close the CD compartment, press PUSH OPEN/ CLOSE on the unit.
2 Press
Audio CD
Recording on a tape
1 Press
on the unit to open the tape compartment and insert a blank tape with the side you want to record on facing upward. Use TYPE I (normal) tape only. Close the compartment. To record from the CD player, press on the unit and place a CD. To record from the radio, tune in the station you want (see Listening to the radio).
3 Press

Press
is
To Pause recording
Stop recording
Tips

on the unit (RADIO/BAND on the remote) repeatedly. Each time you press the button, the indication changes as follows: FM AM
Adjusting the volume or the audio emphasis will not affect the recording level. For the best results, use the AC power as a power source for recording. To erase a recording, proceed as follows: 1 Insert the tape whose recording you want to erase. 2 Make sure that TAPE is displayed. (If TAPE is not displayed, press on the unit or press FUNCTION on the remote until it appears in the display.) 3 Press on the unit.
2 Hold down
To Pause playback
Tip

Press POWER . . .
Tips
. . .
Playing a tape



+ to go forward and to go backward . (forward) or (backward) while playing and hold it until you find the point. ( or on the remote) (forward) or (backward) in pause and hold it until you find the point. ( or on the remote) PUSH OPEN/CLOSE .
1 Press

Press POWER DRIVE WOOFER (WOOFER on the remote) to select or on is more effective. When the the display. WOOFER function works, the ring on the front panel lights up. To return to normal sound, press the button repeatedly until the indication disappears from the display.
Notes
Playback starts from the track/MP3 file you last stopped playing (Resume play). During stop, the track/MP3 file number to be played is displayed. To cancel the resume play (to start play from the beginning of the while the CD is stopped. When you first track/MP3 file), press open the CD compartment or turn off the unit, the resume play is also canceled.
2 Press

Press on the unit. To resume play, press it again.
To Pause playback
Note
on the unit. or forward) (rewind or fast on the unit.

Folder MP3 file
on the unit.
to release or
CFD-G770CPK (2/2)
Other Operations
Using the display


Using the Karaoke function (KARAOKE

PON)
This function reduces the vocal component of the sound source so that you can enjoy Karaoke with your CDs, Tapes, radio programs, or AUDIO IN (the connected component). Use buttons on the unit for the operation.


select the band.
on the unit to
1 Press
2 Press MODE
on the unit for 2 seconds until AUTO flashes in the display.
until SHUF appears in the display. When you select Folder Shuffle Play (MP3 disc only), press MODE on the unit until and SHUF appear in the display. Then press TUNE + or on the unit to select a folder you want. on the unit to start Shuffle Play.
1 Connect a microphone (not supplied) to the MIC

jack on the unit. MIX If the microphone has a power switch, set the switch to ON.
on the unit. The stations are stored in memory from the lower frequencies to the higher ones.
3 Press
Use

2 Press POWER to turn on the unit. 3 Press KARAOKE PON on the unit.
The indicator beside the KARAOKE PON button lights up.
On the remote

select the band.
on the unit to


Tips
4 Play the sound source. 5 Turn MIC LEVEL on the unit to adjust the
microphone volume.

On the remote
on the unit until the preset number you want for the station flashes in the display. on the unit. The new station replaces the old one.
To cancel the Karaoke function

Press KARAOKE PON
Notes
Microphones with a built-in echo function can cause a howling sound. Keep the volume of the microphone low with the MIC LEVEL control . When the howling occurs, turn the head of the microphone away from the speakers. When recording from CDs, radio programs, or AUDIO IN (the connected component) with the Karaoke function is on, only the original sound (with the vocal component) will be recorded on the tape. Input from a microphone connected to the MIC MIX jack cannot be recorded. Even when the Karaoke function is on, the vocal component may not be reduced or adequately reduced for some sound sources.

Play)
1 Press RADIO/BAND

1 Press

Tip
then press DSPL/ENT on the unit (ENTER on the remote) for the tracks/MP3 files you want to program in the order you want. For MP3 files, press TUNE + or first and then press or and DSPL/ENT (ENTER on the remote).



(Repeat Play)
2 Press PRESET + or
stored station.
1 Press
On the remote
Playing order
1 Press REPEAT until 1 appears. or to select the track/ 2 Press MP3 file that you want to repeat. on the unit. 3 Press 1 Press REPEAT until on the unit. 2 Press appears.

4 Press
Use on the unit to start Program Play.
On the remote
Built-in audio cable with stereo-mini plug To AUDIO IN jack

until appears, 1 Press MODE until and then press REPEAT appears. 2 Select the folder by pressing + or . on the unit. 3 Press Tracks/ 1 Select Shuffle Play (see Playing tracks/ MP3 files MP3 files in random order). until SHUF and in random 2 Press REPEAT appear. order on the unit. 3 Press 1 Start Folder Shufle Play (see Playing Files in a tracks/MP3 files in random order). selected on the unit until , folder in 2 Press REPEAT SHUF and appear. random order (MP3 3 Press on the unit. disc only) Programed 1 Program tracks/MP3 files (see Creating your own program). tracks/MP3 files until and PGM 2 Press REPEAT appear. on the unit. 3 Press


or
audio connecting cable (not supplied) To the line output jack

Tips
If you try to program 16 tracks/MP3 files or more, FULL will appear in the display. You can play the same program again, since the program is saved until you open the CD compartment or turn off the power of the unit. You can record your own program. After you have created the program, insert a blank tape and press on the unit to start recording. The resume function does not work during Program Play.

Press POWER
Note
(e.g.,portable digital music player)

plug on the unit to the line output jack of the portable digital music player or other components*.
On the remote

Press REPEAT
Recording starts.

Tip
Should the built-in audio cable become damaged, you can use the to connect an optional component to the unit. Use AUDIO IN jack an audio connecting cable (not supplied) with a stereo mini plug on one end (for the AUDIO IN jack ). Make sure the plug on the other end is suited to the jack on the optional component; for example, a stereo-mini plug for a portable digital music player, or two phono plugs for a TV or VCR.
Notes
10
CFD-G700CP/G770CP/G770CPK SECTION 3 DISASSEMBLY

3-1. DISASSEMBLY FLOW
This set can be disassembled in the order shown below.
SET 3-2. CABINET (UPPER) (1) SECTION (Page 12) 3-3. CABINET (UPPER) (2) SECTION (Page 12)
3-4. CABINET (FRONT) SECTION (Page 13)
3-11. WOOFER KEY BOARD, CD KEY BOARD (Page 17)
3-12. TUNER BOARD (Page 17)
3-14. MAIN BOARD (Page 18)
3-6. FRONT PANEL (Page 14)
3-13. TAPE MECHANISM DECK (Page 18)
3-15. CD BLOCK SECTION (Page 19)
3-17. TC BOARD (Page 20)
3-18. MAIN BELT, SUB BELT (Page 20)
3-16. OPTICAL PICK-UP (KSM-213CDP/C2NP) (Page 19)
3-7. LED BOARD (Page 14) 3-8. SPEAKER (13cm) (Page 15) 3-5. LCD BOARD, AUDIO IN BOARD, HEADPHONE BOARD, POWER KEY BOARD, MICROPHONE BOARD (CFD-G770CPK), VOLUME KEY BOARD (Page 13)
3-9. SPEAKER (10cm) (Page 15)
3-10. POWER BOARD, BATTERY BOARD, D-LIGHT BOARD (CFD-G700CP) (Page 16)
11
Note: Follow the disassembly procedure in the numerical order given.
3-2. CABINET (UPPER) (1) SECTION

1 Open the handle in the direction of the arrow. 2 four screws (+BV tapping (B3))
4 two screws (+BV tapping (B3)) 6 three screws (+BV tapping (B3))
3 Open the cassette lid.
5 Open the CD lid.
3-3. CABINET (UPPER) (2) SECTION

5 CNP391 (5P) 6 CNP301 (5P) 7 CNP393 (4P) 8 CNP390 (6P) (G770CPK) qj handle
9 flexible flat cable (19core) (CN803) q; flexible flat cable (19core) (CN804)
qf CNP394 (3P) qd CNP803 (2P) qs CNP806 (2P) qa CNP807 (2P)
1 Close the cassette lid.
qh cabinet (upper) section
qg CNP391 (5P)
2 Close the CD lid. 4 Open the cabinet (upper) section.
12
3-4. CABINET (FRONT) SECTION
2 six screws (+BV tapping (B3))
5 cabinet (front) section
3 six screws (+BV tapping (B3)) 1 battery lid
3-5. LCD BOARD, AUDIO IN BOARD, HEADPHONE BOARD, POWER KEY BOARD, MICROPHONE BOARD (CFD-G770CPK), VOLUME KEY BOARD
(CFD-G770CPK)
qf MICROPHONE board qd two screws (+BV tapping (B3)) qs POWER KEY board q; button (power) 8 screw (+BV tapping (B2.6))
qg MICVOLUM KNOB
qa
9 screw (+PWH tapping (B2.6)) qh screw (+PWH tapping (B3)) qj HEADPHONE board 2 LCD board
6 5 button (tune) 7 VOLUME KEY board 4 three screws (+BV tapping (B2.6)) 3 screw (+PWH tapping (B2.6))
1 two screws (+P tapping (B2.6))
ql AUDIO IN board
qk screw (+PWH tapping (B2.6))
13
3-6. FRONT PANEL
4 front panel
1 four screws (+BV tapping(B2.6))
2 five screws (+BV tapping(B2.6))
3 three screws (+BV tapping(B2.6))
3-7. LED BOARD

3 light guide ring
2 ornamental ring
4 LED 4 board 5 LED 3 board 1 four screws (+BV tapping (B2.6)) 7 LED 1 board
claw
claw
6 LED 2 board
claw claw
14
3-8. SPEAKER (13cm)
2 speaker (13cm)
1 four screws (+BV tapping (B3))
3-9. SPEAKER (10cm)
4 speaker (10cm)
2 two screws (+BV tapping (B3)) 5 two screws (+BV tapping (B3)) 3 two screws (+BV tapping (B3)) 1 Remove the solderings. 7 speaker (10cm) 6 two screws (+BV tapping (B3))
15
3-10. POWER BOARD, BATTERY BOARD, D-LIGHT BOARD (CFD-G700CP)
CFD-G700CP
5 D-LIGHT board
1 sheet (rear) 8 four screws (+BV tapping (B3))
3 two screws (+BV tapping (B3)) 4 two screws (+BV tapping (B3))
0 POWER board
9 transformer holder
qa transformer bracket
6 four screws (+BV tapping (B3)) qg two terminal ( ), batteries 2 CNP941 (4P) 7 three screws (+BV tapping (B3)) qj BATTERY board
qd four terminal (+, ), batteries
qh screw (+PWH tapping (B3))
qf two screws (+BV tapping (B3)) qs four screws (+BV tapping (B3))
16
3-11. WOOFER KEY BOARD, CD KEY BOARD
1 CNP805 (3P)
2 four screws (+BV tapping (B2.6)) 8 button (CD)
6 four screws (+BV tapping (B2.6))
7 CD KEY board 4 WOOFER KEY board
3 CNP401 (2P)
5 button (SOUND)
3-12. TUNER BOARD
3 three screws (+BV tapping (B3))
4 TUNER board
1 Loosen the screw.
2 CNP1 (11 core)
17
3-13. TAPE MECHANISM DECK

1 three screws (+BV tapping (B3))
3 CNP303 (6 core)
4 tape mechanism deck
2 CN303 (11 core)
3-14. MAIN BOARD

6 three screws (+BV tapping(B3))
1 CNP1 (11 core)
8 MAIN board
5 SW2 (2P) 2 CN303 (11 core)
3 CNP303 (6P) 4 CNP805 (3P)
7 CN805 (21 core)
18
3-15. CD BLOCK SECTION
1 four screws (+PWH tapping (B2.6))
2 flexible flat cable CN201 (21 core)
3 CD block section
3-16. OPTICAL PICK-UP (KSM-213CDP/C2NP)
1 two hooks
2 CD cover
19
3-17. TC BOARD
1 screw
4 TC board
3 Remove soldering from the four points.
yellow red white black
TC board
2 hook
3-18. MAIN BELT, SUB BELT
1 two screws (+BIND DT M2 6) 3 motor assy (M971)
2 hook
4 main belt (B1) 5 sub belt (B1)
20
CFD-G700CP/G770CP/G770CPK SECTION 4 TEST MODE

[MC COLD RESET]
The cold reset clears all data including preset data stored in the memory to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1. In the standby status, press the POWER button to turn the power on. 2. Press three buttons of x , MODE and at last POWER simultaneously. 3. When RESET appears, the machine enters standby status.
[CD SERVICE MODE]

This mode can move the SLED of the optical pick-up, and also can turn the optical pick-up laser power on and off. Procedure: 1. Press the POWER button to turn the power on. 2. Press three buttons of x , VOL + , and SALSA simultaneously. 3. It enters the CD service mode and displays SERVICE. 4. To exit from this mode, press three buttons of x , VOL + , and SALSA simultaneously. Key Operation: PRESET+ > , PRESET . : Use these keys to move the SLED. When PRESET+ > is pressed in this mode, the SLED moves to outer circumference and the message SLED OUT is displayed. When PRESET . is pressed in this mode, the SLED moves to inner circumference and the message SLED IN is displayed. MODE : Use this key to turn the optical pick-up laser power on and off. When the laser power is turned on, the message LD ON is displayed. When the laser power is turned off, the message LD OFF is displayed.
[PANEL TEST MODE]

Enter The Panel Test Mode Procedure: 1. In the standby status, press the POWER button to turn the power on. 2. Press three buttons of REPEAT , x , and DSPL/ENT simultaneously. 3. When the panel test mode is activated, LEDs and segments of LCD are all turned on. Version Check Procedure: 1. In the panel test mode (all LEDs and segments of LCD are turned on), press the ROCK button. 2. On the LCD, date and version are displayed xxxxxxxx. For example, 1127V103. 3. From this status, press the DANCE button, and the destination is displayed. For example, 1014 AU6 or 1014 U2 4. To release from this mode, press three buttons of REPEAT , x , and DSPL/ENT simultaneously.
[CD ERROR CODE]

The past errors of the optical pick-up system (= optical unit + BD board) is displayed as the BD Errors as shown below. Procedure: 1. Press the POWER button to turn the power on. 2. Press three buttons of VOL + , x and DANCE simultaneously. 3. Then, the BD error code is displayed as D0xxxxxx (x means hexadecimal number) on the LCD screen as shown below. 4. Every pressing of the PRESET+ > button in this mode increments the number after D starting from D0 up to D4, and then returns to D0. Every pressing of the PRESET . button in this mode decrements the number after D. The smaller the error code number is, the newer the error content is. 5. To exit from this mode, press the POWER button to turn the power off.
[CHANGE-OVER THE AM TUNING INTERVAL] (G770CP)

The AM tuning interval can be changed over 9 kHz or 10 kHz. Procedure: 1. Press the POWER button to turn the power on. 2. Press the RADIO/BAND button to select TUNER (AM) function. 3. Select the AM BAND mode and press the DSPL/ENT button for an extended time in the AM BAND state. 4. Then, press the AUTO PRESET/RADIO/BAND for an extended time. 5. Next, press the PRESET + PRESET button select either 9k/10k. 6. Finally, press the DSPL/ENT button to set the selected step.
21
Contents of BD Errors Error display example D 0 02 09 01 12 3 4 1 It indicates the error history number 0 to 4: The error code number 0 indicates the newest error. 2 It indicates the error content 01: The focus servo cannot lock-in. 02: GFS is no good (NG). 03: The startup time exceeds the specified period of time (time over) 04: The focus servo is unlocked continuously. 05: Q code cannot be obtained within the specified period of time. 06: The tracking servo cannot lock-in. 07: Blank disc 3 It indicates the on-going processing of optical pick-up system (= optical unit + BD board) when the trouble has occurred. 01: The CD SHIP mode processing is in progress. 02: The POWER OFF processing is in progress. 03: The INITIALIZE processing is in progress. 04: The optical pick-up system (= optical unit + BD board) is in the stop state. 05: The STOP operation is in progress. 06: The startup processing is in progress. 07: The TOC read-in processing is in progress. 08: The SEARCH operation is in progress. 09: The PLAY operation is in progress. 0A: The PAUSE operation is in progress. 0B: The PLAY MANUAL SEARCH operation is in progress. 0C: The PAUSE MANUAL SEARCH operation is in progress. 4 It indicates the operation that is being processed when the trouble has occurred. It indicates the step number of each processing specified by 3 . Because the numbers of steps are different in each processing, this number is different in each processing.
22
SECTION 5 MECHANICAL ADJUSTMENTS

Precaution 1. Clean the following parts with a denatured-alcohol-moistened swab : record/playback head pinch roller erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. (Do not bring the head magnetizer close to the erase head.) 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, appiy suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque Measurement
Mode FWD FWD back tension FF Torque meter CQ-102AS Meter reading 2.0 8.0 mN m (20 to 80 g cm) (0.28 1.12 oz inch) 0.15 0.6 mN m (1.5 to 6 g cm) (0.021 0.083 oz inch) 5 17.7 mN m (50 to 177 g cm) (0.7 2.48 oz inch) 5 17.7 mN m (50 to 177 g cm) (0.7 2.48 oz inch)
CFD-G700CP/G770CP/G770CPK SECTION 6 ELECTRICAL ADJUSTMENTS

CD SECTION
Note: 1. CD Block is basically constructed to operate without adjustment. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10 M impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. 5. Check the focus bias check when optical pick-up block is replaced.
FOCUS BIAS CHECK

oscilloscope (DC range) BD90 board TP (RFI) TP (VC)
+
CQ-102C
CQ-201AS
REW
CQ-201B
Procedure : 1. Connect oscilloscope to TP (RFI) and TP (VC) on the BD90 board. 2. Press the POWER button to turn the power ON, and press the Z PUSH OPEN/CLOSE button to open the CD disc tray. 3. Set disc (YEDS-18) on the tray and press the u (CD) button to playback. 4. Confirm that oscilloscope waveform is as shown in the figure below. (eye pattern) A good eye pattern means that the diamond shape () in the center of the waveform can be clearly distinguished.
VOLT/DIV: 200 mV TIME/DIV: 500 ns
Tape Tension Measurement

Mode FWD Tension Meter CQ-403A Meter Reading more than 80 g cm (more than 2.82 oz inch)
level: 1.2 0.3 Vp-p
Checking Location:
BD90 Board (Side B)
TP (VC)
TP (RFI)
IC101
23
TAPE SECTION
0 dB=0.775 V
Adjustment Location: Record/Playback/Erase Head
1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. Test Tape
Tape P-4-A063 Signal 6.3 kHz, 10 dB Used for Azimuth Adjustment
RECORD/PLAYBACK HEAD AZIMUTH ADJUSTMENT

Procedure: 1. Mode: Playback
test tape P-4-A063 (6.3 kHz, 10 dB)
i jack (J391)
level meter
+
set
Test Tape
Type WS-48A Signal 3 kHz, 0 dB Used for tape speed adjustment
2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak.
Tape Speed Adjustment Procedure: Mode: playback Adjust so that the value on the digital frequency counter is 3,000 Hz. Specification Value:
L-CH peak Output level
within 1dB within 1dB
Digital frequency counter 2,940 to 3,060 Hz
Screw position
R-CH peak L-CH peak R-CH peak
Adjust so that the frequency at the beginning and that at the end of tape winding are between 2,970 to 3,030 Hz.
Screw position
test tape WS-48A (3 kHz, 0 dB) 32 set
digital frequency counter
3. Mode: Playback
test tape P-4-A063 (6.3 kHz, 10 dB) i jack (J391) oscilloscope
i jack (J391)
Adjustment Location:
V set H
waveform of oscilloscope
in phase 45 good
90 135 180 wrong
4. After the adjustments, apply suitable locking compound to the pats adjusted.
Tape speed adjustment control inside motor (M971)
24
TUNER SECTION
0 dB = 1 V
AM Section Setting: RADIO BANDAUTO PRESET button: AM

AM RF signal generator Put the loop antenna close to the set. 32 set 30% amplitude modulation by 400 Hz signal Output level: as low as possible +
i jack (J391)
AM IF ADJUSTMENT Adjust for a maximum reading on level meter. T1 450 kHz AM FREQUENCY COVERAGE ADJUSTMENT (SP, E41, AUS) Frequency Display 531 kHz 1,611 kHz Reading on Digital voltmeter 1.0 0.05 V 5.0 0.7 V Adjustment Part L4 <confirmation> AM FREQUENCY COVERAGE ADJUSTMENT (EXCEPT SP, E41, AUS) Frequency Display 530 kHz 1,710 kHz Reading on Digital voltmeter 1.0 0.05 V 5.2 0.7 V Adjustment Part L4 <confirmation> AM TRACKING ADJUSTMENT (SP, E41, AUS) Adjust for a maximum reading on level meter. L3 CT3 621 kHz 1,404 kHz
level meter
FM Section Setting: RADIO BANDAUTO PRESET button: FM

TUNER board FM RF signal TP-ANT(JW2) generator 0.01 F set 75 kHz frequency deviation by 1 kHz signal Output level: as low as possible TUNER board TP (GND) level meter 32 +
i jack (J391)
AM TRACKING ADJUSTMENT (EXCEPT SP, E41, AUS) Adjust for a maximum reading on level meter. L3 CT3 620 kHz 1,400 kHz FM IF ADJUSTMENT Adjust for a maximum reading on level meter. T2 10.7 MHz FM FREQUENCY COVERAGE ADJUSTMENT Frequency Display 87.5 MHz 108 MHz Reading on Digital voltmeter 1.3 0.3 V 3.0 0.2 V Adjustment Part <confirmation> L2 FM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. L1 CT1 87.5 MHz 108 MHz
digital voltmeter TUNER board TP (CV) TP (GND) 100 k
Repeat the procedures in each adjustment several times, and the tracking adjustments should be finally done by the trimmer capacitors. Remove FM antenna in FM adjustment.
Adjustment Location: See page 26.
25
Adjustment Location:
L3,CT3 AM TRACKING ADJUSTMENT L1,CT1 FM TRACKNG ADJUSTMENT TP-ANT (JW2) T1 L2 T1 AM IF ADJUSTMENT IC1 L4 TUNER BOARD (Component Side) L3 CT3 CT1
L1
T2
T2 FM IF ADJUSTMENT
L2 FM FREQUENCY COVERAGE ADJUSTMENT
L4 AM FREQUENCY COVERAGE ADJUSTMENT
TUNER BOARD (Conductor Side)
TP (GND)
TP (CV)
TP-ANT
JW2
26
CFD-G700CP/G770CP/G770CPK SECTION 7 DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
For Schematic Diagrams. Note: All capacitors are in F unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. f : internal component. C : panel designation.
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice por tant le numro spcifi.
Circuit Boards Location
For Printed Wiring Boards. Note: X : parts extracted from the component side. Y : parts extracted from the conductor side. W : indicates side identified with part number. f : internal component. : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (Side B) Parts face side: (Side A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
MAIN board TC board WOOFER KEY board BD90 board
Indication of transistor.
C Q B E These are omitted.
TUNER board POWER board CD KEY board
H : adjustment for repair. A : B+ Line. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. BD90 Board no mark : CD PLAY TUNER Board no mark : FM ( ) : AM TC Board no mark : FM ( ) : PB < > : REC [ ] : CD PLAY Other Boards no mark : CD PLAY Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : FM f : AM E : TAPE PLAY a : TAPE REC J : CD d : LINE IN Abbreviation AUS : Australian model. CND : Canadian model. E41 : AC 230 V area in E model. E92 : AC 120 V area in E model. MX : Mexican model. SP : Singapore model.
Q B C E These are omitted.

Q B C E
MICROPHONE board (CFD-G770CPK only)

These are omitted.
D-LIGHT board (CFD-G700CP only)
POWER KEY board LED4 board
BATTERY board HEADPHONE board LED3 board LCD board LED2 board VOLUME KEY board AUDIO IN board LED1 board
27
27
7-1. BLOCK DIAGRAM TUNER/CD SECTION
ANT1 FM TELESCOPIC ANTENNA RADIO 6V IC1 FM/AM FRONT-END IF AMP,DET,FM MPX T2 FM IF 10 QUAD T2 23 5 VCC1 VCC2
2 RADIO 6V D11 L1, CT1 FM TRACKING L2 FM FREQUENCY COVERAGE D3 L3, CT3 AM TRACKING L4 AM FREQUENCY COVERAGE L4 RADIO 6V CT3 D2 L3 FERRITE-ROD ANTENNA 22 D10 L1 24 D1 CT1 RADIO 6V L2 21
FM RF IN
FM MIX
MIX OUT
CF2
FM IF-IN
FM DET FM/AM BUFFER DET OUT MPX-IN 16 15 FM MPX MUTE 12 11 R-CH TU-L
FM RF OUT T1 AM IF FM OSC
T1 CF4 6 AM IF-IN AM DET IF BUFFER
MAIN SECTION (Page 29)
ST IND
MO/ST
FM OSC 6V IC2 FM/AM PLL 14 VDD OSC OUT 19 12 FM IN 11 AM IN MO/ST 13 ST IND 8 BAND 7
BAND
IFOUT 17
14 18 13
AM RF IN
AM MIX
RADIO 6V 20 AM OSC AM OSC
X1 75kHz
20 XOUT 19 XIN IF IN 10
IC801(1/2) SYSTEM CONTROLLER 26 O-TU-MUTE
18 LP OUT
OPTICAL PICK-UP BLOCK (KSM-213CDP)

DETECTOR VCC VC A B C D E F
15 16 12 11 10 13 14 9
17 LP IN 16 PD
DO 4 DI 2 CL 3 CE 1
23 I-TU-DO 25 O-TU-DI 24 O-TU-CLK 22 O-TU-CE
+1.7V +3.3V
IC101 RF AMP,DSP,MP3 95 FN11(A) 97 FP11(B) 94 FN12(C) 96 FP12(D) 100 TN1(E) 98 TP1(F) Q301
CD+1.5V
IC201 +1.5V REG

5 VOUT VDD 1 CD+3.3V
LD
7
AUTOMATIC POWER CONTROLLER
91 LDo BUS0 38 5 I/O-MP3-BUS0 6 I/O-MP3-BUS1 7 I/O-MP3-BUS2 8 I/O-MP3-BUS3 17 BUCK(CLK) 19 I-MP3-RST 18 O-MP3-CCEN 3 I-MP3-REQ 43 I-MP3-SBSY 4 O-MP3-M-MUTE 9 F0o
LID-OPEN 10 SW2 PUSH OPEN/CLOSE
GND
8
24 XO X102 16.934MHz 23 XI 42 MD1 IC401 SL/SP MOTOR DRIVER FOCUS/TRACKING COIL DRIVER 26 VD4+ IN4' 24 27 VD418 VD3+ IN3' 20 17 VD310 TRo +3.3V 20 IOO(/MSO) S201 (LIMIT)
BUS1 39 BUS2 40 BUS3 41 BUCK(CLK) 42 RST 37 CCE 43 P100 48 SBSY 54
PD VR
5 6
FOCUS COIL
F+ 4 F
1
TRACKING COIL
T+ 3 T 2 SP+
M401 (SPINDLE) M
2 VO1+ IN1 3 13 DMO LO 30 CD-L 1 VO1-
SP SL+
M402 (SLED)
12 VO2IN2' 9 12 FMO RO 27
R-CH
MAIN SECTION (Page 29)
R-CH is omitted due to same as L-CH. Signal Path : FM
M
SL 11 VO2+
BIAS 23 MUTE 7
11 VREF 21 I01(/UHS0)
: AM : CD
28
28
7-2. BLOCK DIAGRAM MAIN SECTION
G770CPK IC401 MIC MIX AMP J401 MIC MIX RV401 MIC LEVEL Q403 BUFFER CONTROL 6 LIN AMP L L+R L-R R-CH TUNER/CD SECTION (Page 28) IC321(1/2) INPUT SELECT R SW1 SW2 R-CH Q407 LOGIC L-IGOUT J402 15 16 Q406 8 : LINE IN SP292 BUZZER (R-CH) SP291 SPEAKER (R-CH) G700CP IC301 REC/PB PRE AMP TUNER/CD SECTION (Page 28) R-CH Q320 MIX AMP J103 D-LIGHT SYNC OUT 12 Q171 MUTE STBY 8 VDD(SW) TAPE IC321(2/2) SOUND/VOLUME BUFFER AMP 4 L-CH R-CH R-CH 6 L.RO REC AMP 26dB REF LOGIC G700CP/G770CP 7dB L.LD 20 9 L-VOLIN TONE SURROUND L-OUT 27 R-CH Q323 GAIN CONTROL Q321 AMP Q322 LPF IC351 POWER AMP 12 13 10 11 STBY 8 VDD(SW) Q354 AGC Q351 AGC D351 3 IC371 POWER AMP R-CH J391 D414 D415 : TAPE REC L MIX AMP Q401,402 MIC AMP Q405 BUFFER MIC
VDD(SW) D401 R-CH 3 OFF : CD : TAPE PLAY S422 ON KARAOKE PON R-CH is omitted due to same as L-CH. Signal Path : FM
AMP
CD-L
L1-IN
R-CH
L2-IN
MUTE
AUDIO IN CNP2
TU-L
22
L.RAD PB AMP L.IN TAPE
L.LIN
24
TAPE MECHANISM DECK

HRP301 RECORD/PLAYBACK HEAD
SP191 SPEAKER (L-CH) SP192 BUZZER (L-CH)
SP393 WOOFER
TAPE
LINE
REC
PB M971 CAPSTAN/REEL M MOTOR S972 MOTOR S971 PLAY REC
AU 6V
22 21
+9V
CLK
S301 REC/PB
DATA
HE301 ERASE HEAD
21 15 17
MCU I/F
T301 Q301 REC BIAS OSC
D324
D320
D321 Q352 STANDBY SWITCH D322 AU +6V COM VDD G700CP IC901 G770CPK D-LIGHT+4V 11 12 57 55 46 37 33 34 21 28 31 27 3 +4V REG 2 POWER AMP +12V IC806 1 +3.3V 3 REG
WOOFER ON/OFF
WOOFER 1/2
O-P-MUTE
O-BUF-CONT
O-VOL-DATA
TAPE PLAY
O-VOL-CLK
TAPE REC
O-A-MUTE
O-CD-SW
I-MIC-IN
O-TAPE
CD/RADIO +6V IC902 CD +3.3V 3 +3.3V 2 REG Q950,959
+9V
J901 AC IN
93 X0 X802 5.53MHz 92 X1 Q451,452 CLK SHIFT 1 CLK-SHIFT AM 2 CLK-SHIFT FM
Q972 +6V REG VDD(SW)
Q971 +9V REG
IC801(2/2) SYSTEM CONTROLLER
O-CD 56 AU +6V REG CHK 36
VDD(SW) Q954 +6V REG Q952,953 POWER SWITCH D952 D951
DRY BATTERY SIZE "D" (IEC DESIGNATION R20) 8PCS, 12V
I-KEY-WAKE-UP
WOOFER LED1
WOOFER LED2
EEPROM-SDA
EEPROM-SCK
I-RMC(SIRCS)
I-AC/DC-CHK
VDD(SW)
I-KEY-0
I-KEY-1
I-KEY-2
I-KEY-3
I-SUFFIX
RSTX
38
39
40
41 D801
42
48
29 30
SEG0-SEG30 COM0-COM3 63,64,67-89,94-98 59-62
O-PCONT 20
Q951 SWITCH
T901 F901
49 50
45
54 CD/RADIO +6V IC805 +9V 2
D901-904 RECT
Q805 KEY WAKE UP
Q806 SWITCH
Q801,804,815,816 LED DRIVE D403-405, D407-411
VDD(SW) 5 LCD401 LIQUID CRYSTAL DISPLAY 6 D406 OPR/ BATT Q803 DET 1 IC802 EEPROM
VDD(SW)
RESET
D802 FUNCTION SWITCH S409,415-417, S419,421 FUNCTION SWITCH S404,407,411, S412,418,420 FUNCTION SWITCH S401,402,405, S406,413,414 FUNCTION SWITCH S403,408,410
(ILLUMINATION)
IC891 1 REMOTE CONTROL 3 RECEIVER
D461 VDD(SW) D462
29
29
7-3. PRINTED WIRING BOARD BD90 BOARD See page 27 for Circuit Boards Location.
:Uses unleaded solder.
10
11
12
BD90 BOARD (SIDE A)
BD90 BOARD (SIDE B)
M
C401
M401 (SPINDLE)
R405
S201
C405
(LIMIT)
B7 C404 C403
VC
C124
C125
R402
M402 (SLED)
C122
R144 C139 C137 R142 C146 C142 C147 R136 R135 C145 R134 C136
R129
C123 R143
R151 C138
R140
R139
R118
IC401
R128 R120
R130
R127 R126 R125 C153
R415
R414
R408
C140
TP121
C107
C112 R114
C141
RFI
R212
R211 C143
B8
C100
C108
R113
R112
C133
IC201
C106
E
C206
R111
C149
IC101
C109 R154
C110
R110
C144 C148
C105
R210 R209 R218 R208 R207 R206 R205 R204 R203 R157 R156
C152 C151 CN201
C104 R146 R145 R147 R148 C150

C118 C102
C207
5
C115 R155
C201
R153
R219 R220 R221 R222 R223
C101
C205
C117
C120 C119
R104 C113 C103 R101
R201
C306
C130
X102
C132 R106
R105
C202
R303 C128
R302 R304
C126 C127
R102
C301
C116
R149 R150
MAIN BOARD CN805 (Page 36)
B9
R108 R202
C204
C309
Q301
C307
R301
CN301
C303
G
OPTICAL PICK-UP BLOCK KSM-213CDP
Semiconductor Location
Ref. No. IC101 IC201 IC401 Q301 Location E-9 E-2 C-10 F-4
30
30
C302
7-4. SCHEMATIC DIAGRAM BD90 BOARD
See page 44 for Waveforms. See page 44 for IC Block Diagrams. See page 46 for IC Pin Function Description.
C107 0.1
C136 47p
R127 0 R126 R139 47k R129 1k R134 1M R136 R135 22k 470k R118 100k R130 4.7k 0
R142 22k
Q301 2SA2119K
CN301 16P C301 0.1
AUTOMATIC POWER CONTROLLER

TP314 IOP1 TP315 IOP2
R143 47k
R128 470k
R125 0
R140 0
C112 0.1
R120 0
C153 0.1
R114 10k
C108 0.1
TP118
TP119
TP305 TP304 C302 10 C303 10
OPTICAL PICK-UP BLOCK KSM-213CDP
TP301 TP302 TP303 TP306
TP312 APC R302 0
C137 0.01
C138 470p
R303 C306 2.2 100 10V R304 2.2
C307 1
R301 100k
TP117
R212
100 R211 100
TP205 TP206 TP207
CN201 21P
TP116 TP208 C100 0.1 TP115 C139 0.01 TP209 C106 100 10V C141 0.0022 C142 0.1 C140 0.01 TP120 TP114 TP210 R113 10k
TP307
C309 0.001
TP313
RFI
TP121 TP122 TP124 R144 22k C147 0.1
R210
100
TP211 TP212 TP213 TP214 TP215 TP216 TP217 TP218 TP219
R209 100 R218 100k R219 100k R220 100k R208 100 R207 100 R206 100 R205 100 R204 100 R203 100
M401 (SPINDLE)
C105 0.1 SPTP407 SP+ TP408 SL+ TP409 SLTP410 C143 0.01 C144 0.1 C146 470p C145 0.01 C148 47p
A
MAIN BOARD(2/3) CN805 (Page 40)
M M
M402 (SLED)
IC101
RF AMP, DSP, MP3
C133 0.1
R221 100k R222 100k R223 100k
TP309 FTP311 TTP310 T+ TP308 F+
TP123 C149 22p
IC101 TC94A70FG-006
R111 100 R110 10k R112 100 TP224 D1.5V
C104 0.1
TP220 TP221 TP223
C110 0.1 C109 R145 0 R146 0 R147 0 R148 0 R149 0 C150 0.001 R153 1M R155 47 C115 22 6.3V C201 100 10V 0.1 C207 1
TP222
IC201 TK63115SCL-G@GT
R157 100 R156 100 C151 470p C152 470p C205 0.1
C206 1
2
C116 0.1 R154 1M R108 0
IC201 IC B/D
+1.5V REG
R150 0
TP225
R201 0 R202 0
TP226
TP105
TP106
C117 0.022
C119 0.022
R101 220
C127 0.0022
TP109
TP112
TP113
R151 0
TP107
TP110
TP108
TP111
R105
1M
C202 100 10V
C204 0.1
C120 0.01
C102 0.1
C118 0.01
C126 0.1
X102 16.934MHz C130 5p
C124 0.0047
R405 10k R402 2.2k C405 0.1 C404 0.1 C403 0.1
TP102 TRK TP101 FCS C123 470p C122 470p
C103 0.1
C128 5p C132 0.1
R106 1k
R104 0
C125 0.0047
VC
C113 0.1
S201 (LIMIT) IL-SW
R102 C101 0.1
10k
IC401
IC B/D
SL/SP/MOTOR DRIVER FOCUS/TRACKING COIL DRIVER IC401 BA5826SFP-E2
SPSP+
R414 4.7k
R408 2.2k
TP103 TP104
SLED SPDL
SL+
R415 47k
C401 220 10V
SL-
31
31
7-5. PRINTED WIRING BOARD TUNER BOARD
See page 27 for Circuit Boards Location. :Uses unleaded solder.
1 A
10
11
12
13
14
ANT1 FM TELESCOPIC ANTENNA
L3 AM FERRITE BAR ANTENNA
B
R63
JW5
JC11
L3
C32
JC12
D10 JW13
C29
US,CND, MX,E92
CT3
L11 D3 C47 R40
R32
CT1
D1
JW14
C4
C35
JC24
R10
C26 JW4
C8
L1
JW12
D
CNP1
R65
X1
R56
C49
C43
SP,E41,AUS
C1
R50
C41 C42
C27
L21
C51 C61
R57
C52
R30
C37
D2
C33
R5
JW8
R2
IC1
C13
JC13
JC1
TP (CV) JC2
R41
R3
C10
R1
R52
JW6
L4
L2
C30 C31 R31 R33
C62
JC3
C53
R51
US,CND, MX,E92
C54
C55
C95 R54
JC33
R94 R13 C60
JC4
JW7
JW9
R59 R58
C63
R53
C80
C11
IC2
JW11
R60
C59
R55
R61
C18
CF4
CF2 T2
C39
R24 C56 C23 C24
C9
R92
R14 C21
C22
C20
C14 C15
C7
C57 C66 C68 R4

JC5
R91
JC34
C77
TP (GND)
R11
JW10
C78
C12
1-863-43811 (11)
SP,E41,AUS
Ref. No. D1 D2 D3 D10 D11 IC1 IC2 Location C-10 D-8 D-8 B-12 B-12 D-10 F-4
32
32
JC6
T1
JW2
C65
JW3
C34
D11
7-6. SCHEMATIC DIAGRAM TUNER BOARD
See page 44 for Waveforms. See page 45 for IC Block Diagrams.
R91
C51 L3 D3 C41 C42 CT3 R41 JC12 0 JC11 0 C49 R40 C43 C47 C39 L4 R50 X1
C52 R52
C53 R51
C54 R54 C56 R55 C95 C57 R53 C55
C59
C32 C37
1
IC B/D
IC2
R32
R30
D1
C35
C80
C13
D2
C33
JC5
0
C31 JC3 R4
CT1
L1
L2
C34
US,CND, MX,E92
C30
R14 C24 R11 C23 C21 R61 R60 R59 C22 C20 C61 C62 C63 R58
R94
C60
R13
R31
R33
R24
SP,E41,AUS JC24
C68
C66 R92 L11 JC4 US,CND,MX,E92
R56 R57 L21 CNP1
IC1
ANT1
IC B/D
JC2
R10 JC33
JC1 0
C
R65
3 CN2 (Page 40)
0
C1 C11 C12 R2 C9 C7 JC34
C29
C26
C27 C65
R63
JC13
T1 T2
SP, E41 AUS
R3
CF4 C8
D10
D11
C78 JC6 C77 CF2 C18
C10 C4
R1
R5
C14
C15
:US, CND, MX, E92 :SP, E41, AUS
no mark : FM ( ) : AM
33
33
7-7. PRINTED WIRING BOARD TC BOARD
1 A
T301
C305
Q301
C307 R307 C304
JC303
B
R305
R308 C306
R306
R203
R204
C203
R212
IC301
R205
R206
JC304 CN303 R302
R314
R315
C202
C204 C207
R211
JC301
C201
R202
C205 R201
S301 (REC/PB) REC PB
-2
S301 -1
R303
C302 C102
R106
JC306 JC305 JC307 JC308
CN1 (Page 36)
R210
C104 R110
C105
R101
R102
C107 C101
JC302
R304 R105
R309
R301
R103
R104
C103
R111
R112
C303
C301 BLK
E
YEL RED WHT BLK
11
1-688-389-
(11)
(CHASSIS)
L-CH R-CH HRP301 RECORD/PLAYBACK HEAD
HE301 ERASE HEAD
TAPE MECHANISM DECK (1/2)
34
34
7-8. SCHEMATIC DIAGRAM TC BOARD
See page 44 for Waveforms. See page 45 for IC Block Diagram.
IC301 (5,HZ)
R301 C102 TAPE MECHANISM DECK (1/2) C301 C104 C101 C107 R110 R101 R102
R103 C103
R112 R104
IC B/D
R111 JC302
C105
JC306 C303
JC305
C302
JC308 JC307 R309
R210
R201
C205
R211
C204 C202 R202 R203 R212
R304
C207 C201
C203
R204
CN303
R105 R106 R206
JC303
R205
JC301 R303 R302

3 CN1
(Page 40)
R305 T301 C305 R306
R314
R315
JC304
1
Q301
R308
C306
C304
C307
R307
no mark : FM ( < [ ) : PB > : REC ] : CD PLAY
35
35
7-9. PRINTED WIRING BOARD MAIN BOARD
1 A
6
LCD BOARD CN802 (Page 38)
7
LCD BOARD CN801 (Page 38)
8
LED1 BOARD HK402 (Page 38)
JR133 CNP807
C411
9
POWER KEY BOARD KH407 (Page 38) VOLUME KEY BOARD KH405 (Page 38)
10
CD KEYBOARD KH406 (Page 38)
11
F
JR114
C430
G770CPK R446
R451 R409
R452 R427 R420 CN803 CN804
N
MICROPHONE BOARD KH354 (Page 37)
CNP390
SW2
CNP806 CNP803 JW315 JW314 JW304 JW313 JW312 JW302 C461
D462 R493
Ref. No. D320 D321 D322 D323 D324 D351 D414 D415 D461 D462 D801 D802 D804 D805 D951 D952 D953 D954 D955 IC321 IC351 IC371 IC401 IC801 IC802 IC805 IC806 IC901 IC902 Q171 Q271 Q320 Q321 Q322 Q323 Q351 Q352 Q354 Q401 Q402 Q403 Q405 Q406 Q407 Q451 Q452 Q801 Q803 Q804 Q805 Q806 Q812 Q815 Q816 Q950 Q951 Q952 Q953 Q954 Q959 Q971 Q972 Location G-10 G-10 H-10 G-11 F-7 H-8 C-4 B-4 B-10 B-11 C-9 D-9 E-8 D-8 G-9 G-9 G-9 H-5 H-7 F-5 H-9 H-4 B-4 C-7 C-9 C-6 D-6 H-7 G-10 H-4 H-4 F-3 G-7 F-8 F-7 H-10 H-10 G-10 D-3 D-4 D-4 D-4 B-4 B-4 C-6 B-6 C-10 D-9 C-10 C-9 C-9 C-10 C-10 C-10 G-10 G-8 G-8 G-8 G-10 G-10 H-5 H-8
CNP805
C421 JW173 C422 R470
C424
PUSH OPEN/CLOSE
2 KH851 1
C423
R857 R862 R861 R882 R853 R852 R851 R850 R846 R845 R858 R867 R860
JW177 C154 C153

R866
R844 R843
R848
R849
R840
R847
R841
R842
R834
R837 R836
R838
R835
JW303
R881 R859 R855
R879
C253 C426 C254
R856
R863
IC401
R494
R854
JW172
JW300
L158 R463 R460
R489 A Q406
Q407 E
C425
JW299 R906 JW298
R453
C458
C152 E
R447
JW176
C451 Q451 Q452
JW309 JW308
K A D461 A
R461
C819
R454
C457
C454
E E
R868
X802
C815
D415 K
C252
C456
L160
R462 JR138
K JW171
D414
R488
R905
R907
R492 R491
C453
R825
R490
JW292
JW296
C841
C839
JW180
JW181
JW168
C459 C455
E Q805 E E R820 R481 R829 JW290 JW284 R800 R897 R899 Q801 Q804 E
CN1
B
TC BOARD CN303 (Page 34)
R429
C125 C225
R870 JR131 G770CPK R869 R802 R483 JR129

C814
R826 R898
R883
R900 Q815
JW167 C831
C806 R885 R886 JW178
R485 R484
R864 R865
R880 R809 R810
5 8 US,CND, MX,E92
R480
JW166
C846
Q806 R827 SP,E41,AUS A D801 K R821 K C848
Q816 JW291 E Q812 C826

R456 R262
R804
R803 R875 R877 R872
C813
JW112 C432 Q401 E E

R438 R435 R434
JR124 G770CPK
JW162 JW164
4 3 L804
JW283 C833 A C850

JW280 JW279
JR113 JW165
C433 E R441 Q405
R440
JW161 C808
C807
R894
D805
JW182
JW185 G770CPK
R878 R873 R884 R819 R874 R801 R903
R871
C849
R814
R808 C847 R896
R807 JR134
JW285
R430
R432
R431
R433
R437 R436
C415
C402 C431
C416
R816
JR126
R439
R817
R818
JR109
JW260
JW151
R445 R444
R457 R811
C816 R495
R812
R904
R876 C855 C854
R831
Q803 JW218
R160
JW261
C857
C825
R813
R815
R888
C417
C420
C419
IC806
1 2 C803 3 C805
L803
C853
JR127
C852
G770CPK R887
C810
JW288
JW289
C427
JW183
R805
JR128
R482 R823 R822 K K
D802
JW286
R828
JW287
CN2
Q402
IC805
R830 JW282
C828
C827
JW294
JW297
R468
JW169
C820
R419
R418
R448
JW170
IC802
4 1
JW307
JR135 JR155
8 IC 01
L159
JW184
R824
JR137
R839
C
TUNER BOARD CNP1 (Page 32)
JW231 JW210
JW265
JW266
JW262
JW263
D804
R895
JR136
C829
JR110 JW146 C123 JW145

JW150 JW148 JW149 R254 R253
JW225
JW226
JR111
C804
JW154
JW155
JW269
JW270
R486
C851
C843
R902
Q403
JW272
C418
JW264
R893
C223
JW217 JW215
R477
JW153 G770CPK JW152
JW216
JW253 JW254 JR120 JW255 FB831
JW251
R202 R203
R151
JW147
R201
JW246
JR118
R235
E
CNP393
JW144
R251
US,SP,E41
R261
R161
JW113
JW158
JW271
JW156
G770CPK
C856
JW273
JR150
US,SP,E41
C842
R162
C837
JW157
R891
JR151
R901
R892
JW276
JW200
R135 R123 C124 JR140 R120
JR152 C251
R154 R153 JR153 R101 JR108
JW240 JR117 JW241
JW244
JW239
JW221
JW213
JW252
JW223
JW257
JW224
C224
C208 C209 C206 C207
JW243
SP393 (WOOFER)
R223
JW220
JW242
A
CN805 C161
FB833
FB835
FB836
C108 G770CPK C343

C436 CNP301
14
10
R220
C106 C107 C109

R152 R252
JW138
IC321
15 R103
C110 C111 C211 C210 R341
C303 C226 C304 C232 C132

JW134
R125 R129
JW212 JW250
JW259
JW245
20
25
28
JW227
JW228
JW275
C437
JW219
C337 Q320 JW104 R345

R317 R319
JW232
C305
C339
JW142 JW209 R330
D324
A K C333 C334 R338 C338 A Q322
JW233
JW137
R348
JW135 C302
R318
R346
CNP394
R126
R226
JW109
C126 C221 S
R347
JW230
JW160
JW229
POWER BOARD KH903 (Page 42)
TP1
JW140
C121
JW139 JR107
JW247
JW248
G700CP
JW111
R130
FB837
JR122
FB834
R102
C151
R230
R229 R225
BD90 BOARD CN201 (Page 30)
JW222
JW256
JW211
JR121
FB832
C261
K
AUDIO IN BOARD KH355 (Page 37)
TAPE MECHANISM DECK (2/2) S971 PLAY

CNP303 C350
JW234
C362
R204 R104
JW141
JW103
R340
C231
JW120 JW121 JW132 JW131
R324
C131
R331
JW108
R344
C344
R329
Q323
C342
R334 R333 C340 R332 R227 R127
R337
R943
R944
Q959
S972 MOTOR M971 CAPSTAN/ REEL MOTOR
R941
R954 R960 JW196

JW198 JW199
IC902
E 1
C953
C380
C341
R339
JW102
C326
JW123
JW124
JW197
C327
JW122
JW125
CNP397
JW118
M
D-LIGHT BOARD KH356 (Page 37)
G700CP JW130
C335
E Q321
D951
Q952
E D952 K
A K
D321
JW202
JW107
D320 R328 K
D323
C332
R335
R951 E E
Q953
R336 C347
JW195 R961 Q951
D953
Q950 3 C345
R942
C349 A A R342 R343
Q354 C961
R965
JW208
R353 R326
JW136
JW119
C174 R181
R281
C336
R325 JW207 R322 JR106 C366
JW186
JW187
JW188
JW189
JW190
JW192
JW129
C175
C275 C346 C274 R371 C271 C371 C227 C171 C127
R964 R365 R364 R363 R362

R361
Q954
JW194 R360 C356

C357 C358
C955
R359 C355 C354
R356
R351
JW206 G770CPK Q351 Q352 E
D955
C954
C951 JW116 JW117
C957
JW320
A/K D351
R949 R950 R952 R953
C353
C351
R224
R276
C348
JW126
JW133
R179
10
15 R176 Q171 E
R172
R946 R945
JW127
HEADPHONE BOARD KH353 (Page 37)
R275
R279
Q271
R957
R947
JW128
R273 JW205
R948
Q971
IC901
C Q972
5 C361
10
15 C352
IC371
C172 R175
R124 R173
IC351
JR105
36
36
JW204
JW101
C272
C360
R357
C273
R372
JW193
R272
C173
D954
R955
D322
C962 3
R366
CNP391
C381
R966
C301 C359
7-10. PRINTED WIRING BOARDS AUDIO SECTION See page 27 for Circuit Boards Location.
:Uses unleaded solder.
1
G700CP
3
G770CPK
6
J401 MIC MIX
A
L304
M
MAIN BOARD CNP397 (Page 36)
L302
L307
L303
L306
RV401 MIC LEVEL
S422 KARAOKE PON
L305
D401 OFF ON R473 1 R465 KARAOKE PON R426
2 1
4 5 3
J103 D-LIGHT SYNC OUT

L308 6 KH354
C
J402 AUDIO IN
R464
J391
R221
R222
R121
L102
L202
R292 R293 R294
L101
KH355
JR205
JR206
R122
K
1 3
CNP357
SP292 (BUZZER)
SP291 (RCH)
R193 R194 R192 JW406 KH353
L301 JW405
SP191 (LCH)
CNP2
AUDIO IN
CNP392
37
37
C414
SP192 (BUZZER)
KH356
C408
7-11. PRINTED WIRING BOARDS CONTROL SECTION
1 A
R425 R443
6
8
Ref. No. D403 D404 D405 D406 D407 D408 D409 D410 D411 IC891 Location D-4 D-4 D-3 C-3 D-2 D-3 D-1 D-1 D-2 C-1
1 2
R415 R414
1 2
R412 R411
S404
KH407
S418
R413
KH405 S412 S411 R458
S410
VOL
VOL REPEAT MODE AUDIO IN AUTO PRESET RADIO/BAND
SLEEP
DSPL/ENT
R400
S403
R399
S407
S420
R408
R455 S408
POWER
C401
R469
1 3
POWER DRIVE WOOFER

LCD401 (LIQUID CRYSTAL DISPLAY) CN801 CN802
OPR/ R428 BATT
S419
D406
R417
R416
R475
IC891

S409
REGGAETON
S421
FLAT
S417
S415
S416
CNJ408
CNJ406
CNJ4 05
CNJ4 03
407
1 2 1
R472 HK402
CNJ404
D
R479
D4 10
CNJ
2 1
2 1
D4
09
D4
11
D4
07
D4
08
D4
05
D4
03
D4
04
R401 R459
R402
R424 R423 R403
ROCK
DANCE
SALSA
R478
R476
R449
R487
R450
R471
CNP401
D410,D409 (ILLUMINATION)
E
KH408
1 2
S401
S413
S414
S405
S406
R421
R404 R422 R405 R406 R407
R466
KH406
R410
S402
38
38
7-12. SCHEMATIC DIAGRAM MAIN (1/3), AUDIO SECTION
See page 44 for IC Block Diagram.
R104 4.7k
CNP394 3P 3 3 L102 L101 L202
R122 22k R121 22k
CNP357 3P 3
CNP2 3P
1 R221 22k R222 22k
1 J402 AUDIO IN JACK
R204 4.7k R103 47k C109 0.047 C107 0.1 R102 10k C108 0.047 C106 0.1 C231 0.47 50V Q351 KTC3198GR-AT R353 4.7k R341 4.7k R348 4.7k C131 0.47 50V R325 2.2k C366 100p R356 1k Q354 KTC3203Y-AT R351 4.7k R322 0 C351 100 10V D321 1SS355WTE-17 IC321 R2S15904SP R227 10k C335 1 50V R127 10k Q322 2SC3052EF-T1-LEF R340 1k R331 22k R366 10k Q352 RT1P436C-TP-1 D322 1SS355WTE-17
D320 MC2838-T112-1
1 KH355 3P
IC351
BA5417
C210 0.0047
C305 470 16V
C303 10 50V
C232 100p
C121 1 50V
C221 1 50V
C132 100p
C211 0.0022
C111 0.0022
C110 0.0047
C304 0.1
C302 1
R364 1M C360 2.2 50V D351 MC2837 R357 470 C353 100 10V C354 100 10V C355 100 10V C361 0.01 C356 100 10V C359 22 25V R361 2.2k
R365 1M
R362 470
R363 220
CNP393 4P
4 SP393 WOOFER 4 OHM 1 4
C338 10 50V
C352 0.1 C357 0.1 R359 10 C358 0.1 R360 10
R326 1k
SP191
LCH 3.2 OHM
R344 4.7k R332 470k
SP291
CNP392 4P CNP391 5P KH353 5P R192 1k 1 RCH 3.2 OHM
Q321 2SC3052EF -T1-LEF R220 4.7k R120 4.7k C226 C124 2.2 100p 50V R123 4.7k
C224 100p
C326 0.047 R333 10k R335 22k R336 10k Q323 2SK2158-T2B R338 2.2k R337 22k R347 470k C327 0.022 C342 100p
SP192 SP292
C126 2.2 50V R135 0 R235 0
C209 0.047 C207 0.1 R203 47k
C208 0.047 C206 0.1 R202 10k R334 470
IC371
BA5417
C340 100 10V
R293 220 C127 1 50V R124 0 C227 1 50V Q171 2SC3052EF -T1-LEF Q271 2SC3052EF -T1-LEF R224 0 C172 470p C272 470p R275 220 R276 22 C271 47 10V C371 100 10V R372 10k R371 10k C273 100 10V C274 1000 10V C346 1000 25V C275 0.1 R281 4.7 C173 100 10V C174 1000 10V 1 1 R292 1k R294 220 R193 220 R194 220
C223 2.2 50V
C123 2.2 50V R125 22k
R223 4.7k
C225 4.7 50V R126 47k R226 47k
R225 22k R230 47k R130 47k
C339 100 10V
J391 HP JACK
R172 10k R272 10k
R324 2.2k
R329 2.2k R330 470
C334 0.022
C333 0.01
R346 47
R279 4.7k R179 4.7k R173 2.2k
C175 0.1 R181 4.7
L301
R252 4.7k
R328 1k
R152 4.7k
C125 4.7 50V
C337 1 50V R318 470k
Q320 2SC3052EF-T1-LEF R319 4.7k R317 10k
C344 10 50V
D324 MC2838-T112-1 C341 22 25V C336 220 10V C301 220 10V
R175 220 R176 22
R273 2.2k
C171 47 10V
*
R129 0
C332 1 50V R151 R229 0 R345 470 R339 1k
CNP397 3P
KH356 3P
J103 5P L302 0 L306 0 L307 0
R251
C962 0.022
IC901 TK70540SCL-G
C381 100 10V CNP390 6P 6 6 L305 L303 L304 L308 C408 0.047 RV401 10k R426 1k C414 4700p
R961 1k R343 2.2k R342 2.2k Q954 KTC3203Y-AT Q972 KTD2058Y Q971 KTD2058Y
R945 2.2k R946 2.2k R948 2.2k R947 2.2k
J401
R953 2.2k
R952 2.2k
C347 10 50V
C349 220 25V
IC902 TA78033LS
C350 0.022
R950 2.2k
R949 2.2k
D323 1SS355WTE-17
C362 10 50V
Q950 KTA1271Y-AT
Q952 2SA1235F
Q951 RT1N237C-TP-1
C430 1 1 1
R465 2.2k
R464 2.2k
D401 L-34HD S422
D952 MC2836-T112-1 R951 100k

D951 1SS355WTE-17
KH354 6P
R473 4.7k
C380 220 10V
D953 1SS355WTE-17
C345 10 50V R960 470
R954 100k R965 10 C961 220 10V R964 100

D955 UDZSTE-176.8B
C953 0.022
R955 0 C957 220 10V
R966 10 C954 220 16V
R957 0
D954 UDZSTE-1710B
C955 0.022
C951 0.022
R941 2.2k R942 2.2k
R944 2.2k R943 2.2k
Q959 RT1N144C-TP-1
5 C343 10 50V Q953 RT1N431C-TP-1 C348 6800 25V
41
C436 0.1 1
C437 1
CNP301 5P
43
6 1 CNP303 6P
TAPE MECHANISM DECK (2/2)
40
39
39
7-13. SCHEMATIC DIAGRAM MAIN SECTION (2/3)
See page 44 for Waveform. See page 45 for IC Block Diagram. See page 49 for IC Pin Function Description.
L158
CNP807 2P 2
CN2 11P
R854 10k R852 10k R853 10k R851 10k R849 10k R850 10k R848 10k R840 10k R834 10k R838 10k R841 10k R844 10k R837 10k R843 10k R842 10k R846 10k R836 10k R845 10k R835 10k R847 10k R488 22k R905 1k R825 1k R907 10k C815 0.1 R906 1k R491 0 R492 0 R490 0
IC802 S-24CS02AFJ-TB-G
C411 100p
1 CN804 19P
41
*
R901 47k C841 100p C839 220p C828 1000p C827 4700p R860 10k R863 10k R883 1k R870 1k R485 47k R484 47k R826 R898 4.7k R827 C820 0.1
* *
Q805 ISA1235AC1TP-1EF
33
R161 1k R261 1k C261 1 50V R262 0 R456 1k R900 47k C826 0.001 Q812 RT1N144C-TP-1
R867 10k R879 10k R882 10k R861 10k R862 10k R857 10k R858 10k IC801 MB90802NPF -G-127E1 R824 1k R482 1k R823 1k R822 1k R821 1k R808 1k Q452 2SC3052EF -T1-LEF C454 47p Q451 2SC3052EF -T1-LEF C459 10p C455 47p R859 10k R855 10k R856 10k R866 10k R831 1k R814 1k R888 C850 0.01 C849 0.01 C848 0.01 C847 0.01 R869 1k R802 1k R483 47k C833 100p
*
Q806 RT1N436C-TP-1
R820 470k
D801 MC2836-T112-1 D802 MC2836-T112-1
R481 47k
CN1 11P
C161 1
41
C456 22p
X802 5.53MHz
C819 0.1 R868 470
R830 4.7k R829 4.7k R828 4.7k R807 4.7k R480 47k
R468 1k R448 1k
R816 1k R815 1k R887 47k

C852 100p C857 100p
35
R453 1k C458 0.01 R454 10k
C457 0.01
C453 22p
C451 8p
R881 10k
IC805 S-80828CNMC -B8NT2G
L160
*
R871 470
R810 4.7k R801 470 R904 1k
R839 47k Q816 KTA1271Y-AT
L159
R885 1k R886 47k
R812 1k
R903 1k
R813 1k
R876 220
R811 10k
R457 10k
C813 0.1
R805 1k
R872 1k
R877 1k
R880 1k
R803 1k
R875 1k
R804 1k
R865 1k
R817 1k
R864 1k
R809 1k
R878 1k
R874 1k
R819 1k
R818 1k
R902 1k
R873 1k
Q815 RT1P144C-TP-1 Q801 RT1N144C -TP-1 R800 2.2k
C843 100p
C831 100p C846 100p D804 1SS355WTE-17 C855 100p C854 100p
41
R897 100 R899 100 Q803 2SC3052EF -T1-LEF

C856 100p C842 100p C814 0.1
C816 100p
C837 100p
IC806 XC6202P332FR C805 100 10V C804 0.01 C803 0.1 C806 1 C825 1
L803 C808 100 10V C807 0.01
C851 100p
R884 470
Q804 RT1N144C-TP-1
CN803 19P R493 1k KH851 2P 2 1

D462 UDZSTE-175.1B
R895 10
C853 100p
D805 R894 1SS355WTE-17 10
SW2
R495 100k L804 JW C829 100p R893 0
R896 10k R892 0
R162 47k R160 47k
C461 10 50V CNP805 3P 3
39
R486 100k R477 100k C810 0.01 R891 47k
1 R461 470 R460 R463 R462 220 220 470 D461 MC2838-T112-1 CNP803 2P 2 1 CNP806 2P 2 1
41
R451 1k R452 1k
R409 1k R427 1k
41
R420 4.7k
41
FB832 0
FB834 0 FB831 0 FB833 0 FB837 0
R253 4.7k
C251 10 50V C151 10 50V R254 10k R153 4.7k
R101 0
R201 0
R154 10k
FB836 FB
CN805 21P 21
FB835 FB
41 31
40
40
7-14. SCHEMATIC DIAGRAM MAIN (3/3), CONTROL SECTION
See page 44 for IC Block Diagram.
R418 1k
R494 47k
R489 47k
Q407 RT1N144C-TP-1
R419 47k D414 1SS355WTE-17
Q406 RT1N144C-TP-1 IC891 RPM7140-V4
D415 MC2836-T112-1
CN801 19P
R469 100k R475 220k
C401 1
R428 220 D406 L-34HD LCD401 R436 2.2k R435 4.7k Q402 2SC3052EF -T1-LEF Q401 2SC3052EF -T1-LEF C432 100p R439 470 C418 C402 50V C431 100p R429 2.2k R433 47k C420 10V R430 47k C415 R431 470 R432 1k R434 1k C416 10V C419 50V Q403 RT1N144C-TP-1 R444 100k R446 470 50V R445 4.7k R440 470 C427 50V C433 100p Q405 2SC3052EF -T1-LEF C422 10V C421 50V R470 470 R441 220k C424 50V IC401 BA3837 R437 1k C417 R438 1k 50V
C425
C254 220p
C426
R447 47k
C423 22 25V
C252 C152 C253
50V 50V
40
C154 220p
C153
* *
40
39
40
R411 220 R458 100 S411 SWITCH S412 SWITCH S404 SWITCH S418 SWITCH S420 SWITCH S407 SWITCH R412 470 R413 1k R414 1k R415 2.2k R443 1k R425 2.2k KH407 2P R455 100 S408 SWITCH KH405 2P S410 SWITCH S403 SWITCH R400 220 R399 470 R408 1k
CN802 19P
40
40
CNP401 2P
KH408 2P
R410 220 R466 100 S401 SWITCH
R421 470
R422 1k
R404 1k
R405 2.2k
R406 1k
R407 2.2k
HK402 2P
R401 220 CNJ403 2P CNJ404 2P CNJ405 2P CNJ406 2P CNJ407 2P CNJ408 2P R459 100 R471 220 D403 IL4345V22D0TDT02 R449 220 D405 IL4345V22D0TDT02 R476 220 D407 IL4345V22D0TDT02 R478 220 D409 IL4345V22D0TDT02 S409 SWITCH
R402 470
R403 1k
R423 1k
R424 2.2k
R416 2.2k
R417 1k
S402 SWITCH
S413 SWITCH
S414 SWITCH
S405 SWITCH
S406 SWITCH
S415 SWITCH
S416 SWITCH
S421 SWITCH
S417 SWITCH
S419 SWITCH
KH406 3P
40
R472 220
D404 IL4345V22D0TDT02
R450 220
D408 IL4345V22D0TDT02
R487 220
D411 IL4345V22D0TDT02
R479 220
D410 IL4345V22D0TDT02
40
41
41
7-15. PRINTED WIRING BOARDS POWER SECTION
1 A
Ref. No. D901 D902 D903 D904 Location C-7 C-6 C-7 C-6
KH902 T901 POWER TRANSFORMER

5
1 KH903
J901 ~AC IN
C909
JW274
FH901
FH902
C928
F902 D902
C902
C927
C901 D901 C903 D903
JW402
* Not Replaceable: Built in Transformer *
C904 D904
D
CNP941
E
JW944 JW943 JW942 JW941
DRY BATTERY SIZE "D" (IEC DESIGNATION R20) 8PCS,12V
42
42
7-16. SCHEMATIC DIAGRAM POWER SECTION
39
KH903 5P
J901
T901 POWER TRANSFORMER
FH901 HOLDER FUSE
FH902 HOLDER FUSE C901 D901 0.022 1N5401-C352 1N5401-C352 0.022 C927 1 C903 0.022 1N5401-C352 1N5401-C352 0.022
C909 2200 25V
KH902 4P 1
CNP941 1 4P
F902 FUSS GLASS TUBE
D902 C902
JW944 JW JW941 JW JW942 JW
JW943 JW
* *
C928 1 D903 D904 C904
43
43
Waveforms BD90 Board
IC Block Diagrams TUNER Board MAIN Board BD90 Board IC201 TK63115SCL-G@GT
VIN 1 5 VOUT
IC101 ia (RFi) (CD PLAY mode)
IC2 w; (XOUT)
1 IC801 os (X1)
IC401 BA5826SFP-E2
VO1(-) 1
CH1
28 GND 27 VOL(-) LEVEL SHIFT

CH4
VO1(+) 2
GND 2
26 VOL(+) LEVEL SHIFT 25 IN4
1.3 Vp-p 200 mV/DIV, 500 ns/DIV
13.3 s 500 mV/DIV, 5 s/DIV
1.5 Vp-p
3.4 Vp-p 180 ns 1 V/DIV, 100 ns/DIV
V REF
IN1 3
13.3K
ON/OFF CONTROL
13.3K
IC101 wf (XO) (CD PLAY mode) TC Board
10K
THERMAL & OVER CURRENT PROTECTION 4 NC

RESET 4
T.S.D. REGULATOR,BIAS DROP 100
VCONT 3
24 IN4' 23 BIAS
REGB 5
1
3.3 Vp-p 59.1 ns 1 V/DIV, 20 ns/DIV
Q301 C (REC)
REGOUT 6
VCC VCC
22 VCC 21 VCC 20 IN3'
13.3K
MUTE 7 GND 8
MUTE
13.3K
10K
4 Vp-p 19.5 sec 1 V/DIV, 5 s/DIV

IN2' 9 IN2 10 VO2(+) 11
CH2
19 IN3 LEVEL SHIFT LEVEL SHIFT 18 VO3(+)

CH3
10K
T301, HRP301 (YEL)
17 VO3(-) 16 RESET 15 OPIN
VOL(-) 12 GND 13 OPOUT 14
MAIN Board
40 Vp-p 19.5 sec 10 V/DIV, 5 s/DIV
INR3 1 INR2 2 INR1 3
MUTE INPUT SELECTOR
IC321 R2S15904SP
IC401 BA3837
VCC 1
28 INR4
27 LOUT
26 ROUT
LOUT 3 FK 4 SW2 SW1
LOGIC L L-R L+R R
MIC 2
16 C 15 B 14 A
13 ROUT
INL1 4 25 AGND INL2 5 INL3 6 INL4 7

INPUT GAIN CONTROL INPUT SELECTOR MODE SELECTOR
TK 5 LIN 6
12 LP
24 VCC
11 LP
REF
23 REFIN
10 LP
IGOUTL 8
0 - +12dB /2dB step
MUTE
22 DATA
SURROUND
MCU I/F
9 RIN
21 CLK 20 DGND
VOLINL 9 IGOUTR 10
VOLUME 0 - -89dB. INPUT GAIN CONTROL 0 - +12dB/2dB step VOLUME
BIAS 7 GND 8
19 TRER
VOLINR 11
0 - -89dB. BASSR1 12 BASSR2 13 BASSL1 14

TONE CONTROL R ch BASS/TREBLE TONE CONTROL L ch BASS/TREBLE
18 TREL 17 NC 16 NC 15 BASSL2
44
44
MAIN Board IC805 S-80828CNMC-B8NT2G

OUT VDD 1 2 5 NC
TC Board IC301 TA2068N (5, HZ)
AGC 1 L.PO 2 L.NF 3 REC AMP1 26dB

ALC2 ALC1
LINE NAB AMP1 BUF AMP A1

TAPE
24 L.LIN 23 MIC I/EX
TAPE RADIO
22 L.RAD 21 REC
L.RO 4
VREF
L.IN 5
VSS 3 4 NC
BUF AMP MUTE MONITOR AMP B1 ON ON BUF AMP B2 MUTE 7dB
20 L.LO LOGIC 19 VCC
REF AMP 2.1
DET
REF 6 GND 7 R.IN 8 R.RO 9
7dB 18 R.LO MONITOR AMP 17 LINE
REC AMP2 26dB
ON
MUTE
R.NF 10 R.PO 11 NAB AMP2 MIC AMP1 MIC.NF 12
TAPE
TAPE
RADIO
16 R.RAD 15 TAPE
BUF AMP A2
LINE
14 R.LIN 13 MIC
TUNER Board IC1 TA2149BN

GND1 1 FM RF-IN 2 AM LOW CUT 3 MIX OUT 4 FM MIX AM MIX FM OSC AM OSC BUFF BUFF VCC2 5 AF IF-IN 6 FM IF-IN 7 GND2 8 AGC 9 QUAD 10 R-OUT 11 MUTE L-OUT 12 AGC FM DET ST/MO FM/AM VCO DIVIDE DECODE 14 LPF2/MO-ST 13 LPF1/BAND AM DET AM IF FM IF 1/8 LEVEL DET IF BUFF 1/1 OR 1/16 ST SW FM RF 24 FM RF-OUT 23 VCC1 22 AM RF-IN 21 FM OSC
IC2 LC72137M-TLM-E
CE DI CL DO 1 2 3 4
CCB I/F 20 XOUT 19 XIN
20 AM OSC 19 OSC-OUT
REFERENCE DIVIDER MUTE 5 6 7 8 9

DATA SHIFT REGISTER LATCH
18 ST-IND
FM/AM BAND
12BITS PROGRAMMABLE DIVIDER
PHASE DETECTOR CHARGE PUMP
18 LP-OUT 17 LP-IN 16 PD 15 VSS
AF BUFF
IF REQ AF
17 IF-OUT 16 DET-OUT 15 MPX- IN
ST-IND BAND
UNLOCK DETECTOR POWER ON RESET 14 VDD 13 MO/ST
UNIVERSAL COUNTER
SWALLOW COUNTER 1/16,1/17 4BITS
1/2
12 FM IN
11 AM IN
IF IN 10
45
IC Pin Function Description BD90 BOARD IC101 TC94A70FG-006 (RF AMP, DSP, MP3) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Pin Name AVSS3 RFZi RFRP SBAD/RFDC FEi TEi TEZi AVDD3 FOo TRo VREF FMO DMO VSSP3 VCOi VDDP3 VDD1 VSS1 FGiN Io0(/HSo) Io1(/UHSo) XVSS3 Xi Xo XVDD3 DVSS3 Ro DVDD3 DVR Lo DVSS3 VDDT3 VSS1 VDD1 VDDM1 SRAMSTB RST BUS0 BUS1 BUS2(So) BUS3(Si) BUCK(CLK) CCE TEST IRQ AoUT3(Po4) AoUT2(Po5) I/O I O O O O I O O O O O I I I I O O O I I I I I I I I I I O O Description Ground terminal (Used CD analog 3.3V) RF ripple zero cross signal input terminal RF ripple signal output terminal (Used zero cross) Not used (Open) Not used (Open) Tracking error signal output terminal (Not used (Open)) Tracking error signal input terminal (Used zero cross) Power supply terminal (Used CD analog 3.3V) Focus servo equalizer output terminal Tracking servo equalizer output terminal REF of analog power supply terminal Feed servo equalizer output terminal Disc servo equalizer output terminal Ground terminal (Used DSP VOC 3.3V) PD output terminal (Used VCO) Power supply terminal (Used DSP VCO 3.3V) Power supply terminal (Used digital 1.5V) Ground terminal (Used digital 1.5V) FG signal input terminal (Used CAV) (Not used (Fixed to L)) Play speed mode flag input terminal Not used (Open) Ground terminal (Used system clock 3.3V) System clock input terminal (16.934MHz) System clock output terminal (16.934MHz) Power supply terminal (Used system clock 3.3V) Ground terminal (Used DAC) Audio R-ch data output terminal Power supply terminal (Used DAC 3.3V) REF voltage terminal (Used DAC) Audio L-ch data output terminal Ground terminal (Used DAC 3.3V) Power supply terminal (Used Digital I/O 3.3V) Ground terminal (Used Digital 3.3V) Power supply terminal (Used digital 1.5V) Power supply terminal (Used 1M bit SRAM 1.5V) 1M bit SRAM standby input terminal (Not used (Fixed to L)) Reset signal input terminal Data input terminal (BUS line) Data input terminal (BUS line) Data input terminal (Serial output) Data input terminal (Serial input) BUS clock input terminal (Serial clock input) Clip enable input terminal (U-com interface) Test setting terminal (Not used (Fixed to L)) Cut in DSP input terminal (Not used (Fixed to L)) Not used (Open) Not used (Open)
46
Pin No. 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96
Pin Name Pio0 Pio1 Pio2 Pio3 VSS1 VDDT3 SBSY SBOK/FOK IPF SFSY/LOCK ZDET GPIN MS DoUT(Po6) AoUT1(Po7) BCK(Po8) LRCK(Po9) AiN(Pi4) BCKi(Pi5) LRCKi(Pi6) VDD1 VSS1 AWRC PVDD3 PDo TMAXS TMAX LPFN LPFo PVREF VCoF PVSS3 SLCo RFi RFRPi RFEQo VRo RESiN VMDiR TESTR AGCi RFo RVDD3 LDo MDi RVSS3 FNi2(C) FNi1(A) FPi2(D)
I/O O I I I O O O O O I I O O O O I I I O O O O I O O O I I O O O O I O O I I I I REQ output terminal Not used (Open) Not used (Open) Not used (Open) Ground terminal (Digital 3.3V)
Description
Power supply terminal (Digital I/O 3.3V) Sub code block sync output terminal Not used (Open) Not used (Open) Not used (Open) DAC zero data detect flag output terminal (Not used (Open)) General purpose input terminal (Not used (Fixed to L)) U-com I/F mode select input terminal (Fixed to H) Not used (Open) Not used (Open) Not used (Open) Not used (Open) Data input terminal (Used DAC) (Not used (Fixed to L)) Bit clock input terminal (Used DAC) (Not used (Fixed to L)) Channel clock input terminal (Used DAC) (Not used (Fixed to L)) Power supply terminal (Digital 1.5V) Ground terminal (Digital 1.5V) Not used (Open) Power supply terminal (PLL 3.3V) Phase error signal of EFM signal and PLCK signal output terminal Not used (Open) Output terminal of TMAX detect signal Reverse input terminal of AMP (PLL-LPF) Output terminal of AMP (PLL-LPF) 1.65V REF power terminal (Only PLL) VCO filter output terminal Ground terminal (PLL 3.3V) EFM slice level output terminal RF signal input terminal RF ripple signal input terminal RF equalizer output terminal 1.65V REF voltage output terminal REF resister terminal (22k/0.01u) REF voltage of APC circuit output terminal LPF terminal (RFEQO offset correct) RF signal adjustment AMP input terminal RF signal AMP output terminal 3.3V Power supply terminal (RF AMP) Laser diode AMP output terminal Monitor photo diode AMP input terminal Ground terminal (RF AMP 3.3V) Main beam input terminal (Connect to pin diode C) Main beam input terminal (Connect to pin diode A) Main beam input terminal (Connect to pin diode D)
47
Pin No. 97 98 99 100
Pin Name FPi1(B) TPi(F) TNPC TNi(E)
I/O I I O I
Description Main beam input terminal (Connect to pin diode B) Sub beam AMP input terminal (Connect to pin diode F) Capacitor connect terminal to the middle pointof TNI/TPI input register Sub beam AMP input terminal (Connect to pin diode E)
48
MAIN BOARD IC801 MB90802NPF-G-127E1 (SYSTEM CONTROLLER) Pin No. 1 2 3 4 Pin Name CLK-SHIFT_AM CLK-SHIFT_FM I-MP3-REQ O-MP3-M-MUTE I/O-MP3-BUS0 5 to 8 I/O-MP3-BUS1 I/O-MP3-BUS2(SO) I/O-MP3-BUS3(SI) 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 to 41 42 43 44 45 46 47 48 49 50 51 to 53 I-RMC (SRCS) LID-OPEN TAPE PLAY TAPE REC NC(GND) NC(OPEN) VCC VSS O-MP3-BUCK(CLK) O-MP3-CCEN O-MP3-XRST O-PCONT O-P-MUTE O-TU-CE I-TU-DO O-TU-CLK O-TU-DI O-TU-MUTE WOOFER_ON/OFF WOOFER_1/2 WOOFER_LED1 WOOFER_LED2 O-A-MUTE AVCC O-VOL-DATA O-VOL-CLK AVSS I-REG6V-CHK I-MIC-IN I-KEY0-3 I-KEY-WAKE-UP I-MP3-SBSY VSS I-AC/DC-CHK O-BUF-CONT NC I-SUFFIX EEPROM-SDA EEPROM-SCK MD2-0 I I I I O O O O O O I O O O O O O O O O O I I I I I I O I I/O O I SIRCS remote control signal input CD lid open detect signal input Tape PLAY detect signal input Tape REC detect signal input Not used (Fixed to L) Not used (Open) Power supply terminal (+3.3V) Ground terminal Bus clock signal output to CD-DSP-MP3 decorder (IC101) Chip enable signal output to CD-DSP-MP3 decorder (IC101) Reset signal output to CD-DSP-MP3 decorder (IC101) Power control signal output (H:ON) Mute signal output to power amplifier Chip enable signal output to Tuner PLL (IC2) Serial data input from Tuner PLL (IC2) Serial clock signal output to Tuner PLL (IC2) Serial data output to Tuner PLL (IC2) Mute signal output to Tuner PLL (IC2) Woofer control signal output (H:ON/L:OFF) Woofer level control signal output (H:Level-2, L:Level-1) Woofer LED control signal output (H:Level-1) Woofer LED control signal output (H:Level-2) Mute signal output Power supply terminal (+3.3V) Serial data output to EVR (IC321) Serial clock output to EVR (IC321) Ground terminal 6V regulator check input MIC input detect (H:Detect) Key input Key wake-up input Sub code block sync input terminal Ground terminal AC/DC detect (L:AC) MIC buffer control signal output Not used (Open) Suffix control input Serial data input/output to EEPROM (IC802) Serial clock output to EEPROM (IC802) Flash mask (Fixed to MD2:L, MD1:H, MD0:H) I/O Two-way data bus for CD-DSP-MP3 decorder (IC101) I/O O O I O Description Clock shift signal output for AM radio Clock shift signal output for FM radio Request signal input from CD-DSP-MP3 decorder (IC101) Mute signal output to Spindle and Sleding motor driver (IC401)
49
Pin No. 54 55 56 57 58 59 to 62 63, 64 65 66 67 to 89 90 91 92 93 94 to 98 99 100
Pin Name RSTX O-CD-SW O-CD O-TAPE VLCD COM1-4 SEG1,2 VCC VSS SEG3-25 VCC VSS X1 X0 SEG26-30 NC NC
I/O I O O O I O O O O I O System reset signal input Pre-amp select signal output
Description
CD+3.3V regulator control signal output Pre-amp select signal output LCD power setting input Common signal output to the LCD Segment signal output to the LCD Power supply terminal (+3.3V) Ground terminal Segment signal output to the LCD Power supply terminal (+3.3V) Ground terminal Main clock output terminal (4.19MHz) Main clock input terminal (4.19MHz) Segment signal output to the LCD Not used (Open) Not used (Open)
50
CFD-G700CP/G770CP/G770CPK SECTION 8 EXPLODED VIEWS

NOTE: -XX and -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The mechanical parts with no reference number in the exploded views are not supplied. Abbreviation AUS : Australian model CND : Canadian model E41 : AC 230V area in E model E92 : AC 120V area in E model MX : Mexican model SP : Singapore model The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
8-1.
OVERALL SECTION
8 8
cabinet (upper) section
cabinet (rear) section
SP191
4
SP291
CNP2 cabinet (front) section
1
Ref. No. 1 2 3 4 5 6 Part No. 2-895-570-01 2-895-569-01 A-1244-296-A 3-252-827-01 3-252-828-01 Description LID, CORD CASE CASE, CORD AUDIO IN BOARD, COMPLETE SCREW (B2.6), (+) BV TAPPING SCREW (B2.6), (+) PWH TAPPING Remark Ref. No. 7 8 9 CNP2 SP191 SP291 Part No. 2-895-573-01 3-254-145-11 2-895-574-01 1-833-922-11 Description LID, BATTERY SCREW (B3), (+) BV TAPPING HANDLE CORD, CONNECTION (WITH PLUG) Remark
3-254-143-11 SCREW (B3), (+) BV TAPPING
1-826-684-11 SPEAKER (10cm) 1-826-684-11 SPEAKER (10cm)
51
8-2.
CABINET (FRONT) SECTION 63 62 65 64 66

G770CPK
not supplied
77
68
69 71 55
65 66
67 53 54 61
70 77 65
55 60
65
not supplied
72
SP393 D404
73
76 52
D409 D403 D410 D407 D405
75 51 55
D411
59 74
56
57
D408
58
Ref. No. 51 52 53 54 55 56 57 58 59 60 60 60 61 62 63 64 65 66 67 68
Part No. X-2177-000-1 2-895-583-01 A-1244-292-A 3-254-151-01 3-254-143-11 3-254-140-01 2-895-575-01 2-895-579-01 2-895-576-01 X-2177-001-1 X-2177-002-1 X-2177-003-1 3-198-121-01 A-1244-297-A 3-252-830-01 2-895-584-01 3-252-827-01 3-252-828-01 A-1244-294-A 2-657-081-02
Description PANEL, (FRONT) SUB ASSY COVER, PANEL LCD BOARD, COMPLETE SCREW (B2.6), (+) P TAPPING SCREW (B3), (+) BV TAPPING
Remark
Ref. No. 69 70 71 72 73 74 75 76 77 D403 D404 D405 D407 D408 D409 D410 D411 SP393
Part No. 2-895-594-01 A-1244-295-A 2-895-585-01 A-1244-293-A A-1243-618-A A-1243-619-A A-1243-620-A A-1243-621-A 3-831-441-11 6-501-452-01 6-501-452-01 6-501-452-01 6-501-452-01 6-501-452-01 6-501-452-01
Description
Remark
CAP, SWITCH (G770CPK) MICROPHONE BOARD, COMPLETE (G770CPK) BUTTON, TUNE VOLUME KEY BOARD, COMPLETE LED1 BOARD, COMPLETE LED2 BOARD, COMPLETE LED3 BOARD, COMPLETE LED4 BOARD, COMPLETE CUSHION (B) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION)
SCREW (B2.6), (+) BV TAPPING RING, ORNAMENTAL HOLDER, RING RING, LIGHT GUIDE CABINET, (FRONT) SUB ASSY (G770CPK) CABINET, (FRONT) SUB ASSY (G700CP) CABINET, (FRONT) SUB ASSY (G770CP) SHEET (WIRE), ADHESIVE HEADPHONE BOARD, COMPLETE SCREW (B3), (+) PWH TAPPING BUTTON, POWER SCREW (B2.6), (+) BV TAPPINGNG SCREW (B2.6), (+) PWH TAPPING POWER KEY BOARD, COMPLETE KNOB, MICVOLUM (G770CPK)
6-501-452-01 DIODE 1L4345V22DOTDT02 (ILLUMINATION) 6-501-452-01 DIODE 1L4345V22DOTDT02 (ILLUMINATION) 1-826-683-11 SPEAKER (13cm)
52
8-3.
CABINET (REAR) SECTION

G700CP
114 106 104 103

J901
112
101 101 106 105
T901
106 106
F902
106 101 106 102 101 107 109 108
106 106
110 109
not supplied
101 113 101 111
Ref. No. 101 102 102 103 103 104 105 105 105 105 106 107
Part No. 3-254-143-11 2-895-581-01 2-895-581-11 A-1243-633-A
Description
Remark
Ref. No. 108 109 110 111 112 113 114 0 F902 0 J901 0 J901 0 T901 0 T901
Part No.
Description
Remark
SCREW (B3), (+) BV TAPPING HOLDER, TRANSFORMER (G770CP/G770CPK) HOLDER, TRANSFORMER (G700CP) POWER BOARD, COMPLETE (US, CND, MX, E92) A-1244-369-A POWER BOARD, COMPLETE (SP, E41, AUS) 2-895-596-01 2-895-565-01 2-895-565-11 2-895-565-21 2-895-565-31 BRACKET (TRANSFORMER) CABINET (REAR) (MX) CABINET (REAR) (G700CP) CABINET (REAR) (CND, E92) CABINET (REAR) (SP, E41, AUS)
2-067-415-01 TERMINAL (+, ), BATTERY 2-895-597-01 TERMINAL (), BATTERY A-1244-301-A BATTERY BOARD, COMPLETE 3-252-830-01 A-1244-302-A 3-238-135-01 3-096-719-01 1-532-504-33 1-526-838-11 1-540-009-11 1-435-964-12 1-435-965-12 SCREW (B3), (+) PWH TAPPING D-LIGHT BOARD, COMPLETE (G700CP) TERMINAL (), BATTERY SHEET (REAR) FUSE (T4AL/250V) INLET, AC 2P (- AC IN) (SP, E41, AUS) INLET, AC (- AC IN) (US, CND, MX, E92) TRANSFORMER, POWER (US, CND, MX, E92) TRANSFORMER, POWER (SP, E41, AUS)
3-198-219-01 CUSHION, CAP 4-233-372-02 FOOT (FELT)
53
8-4.
CABINET (UPPER) SECTION-1

168 169
#1 165 166 168

S201
168
167
not supplied
164 163
170
tape mechanism deck section
163 162
160 161
159
158 not supplied 155 154

cabinet (upper) section-2
157 156 151 152 153
Ref. No. 151 152 153 154 155 156 157 158 159 0 160 161 162 163 164 165
Part No. 2-108-743-01 2-895-588-01 2-895-589-01 2-895-590-01 2-895-591-01 2-895-592-01 2-895-593-01 3-252-827-01 3-923-736-01 8-820-126-02 3-931-379-21 3-931-379-31 3-252-828-01 1-832-404-21 A-1244-423-A
Description CUSHION KEY CASSETTE BUTTON, REC BUTTON, PLAY BUTTON, REW BUTTON, FF
Remark
Ref. No. 166 167 167 168 169 169 169 169 169 169 170 S201 #1
Part No.
Description
Remark
1-832-613-21 CABLE, FLEXIBLE FLAT (21 CORE) A-1244-418-A TUNER BOARD, COMPLETE (US, CND, MX, E92) A-1244-419-A TUNER BOARD, COMPLETE (SP, E41, AUS) 3-254-143-11 SCREW (B3), (+) BV TAPPING A-1244-300-A MAIN BOARD, COMPLETE (MX, E92) A-1244-370-A A-1244-371-A A-1244-372-A A-1244-373-A A-1244-374-A MAIN BOARD, COMPLETE (G700CP) MAIN BOARD, COMPLETE (CND) MAIN BOARD, COMPLETE (SP) MAIN BOARD, COMPLETE (E41) MAIN BOARD, COMPLETE (AUS)
BUTTON, STOP BUTTON, PAUSE SCREW (B2.6), (+) BV TAPPING COVER, CD OPTICAL PICK-UP (KSM-213CDP/C2NP) RUBBER, VIBRATION PROOF RUBBER, VIBRATION PROOF SCREW (B2.6), (+) PWH TAPPING CABLE, FLEXIBLE FLAT (16 CORE) BD90 BOARD, COMPLETE
2-895-061-01 TERMINAL, ANTENNA 1-771-853-11 SWITCH, DETECTION (LIMIT) 7-685-853-04 SCREW +BVTT 2X6 (S)
54
8-5.
CABINET (UPPER) SECTION-2

203
205
204
221
202
206 207 208 209
201 210 219 218 217 211 216

not supplied
215 220 212 213 211

not supplied
SW2
214
215
215
Ref. No. 201 201 202 203 203 203 204 205 206 207 208 209 210 211
Part No. 2-895-568-01 2-895-568-11 2-895-060-01 2-895-572-01 2-895-572-11 2-895-572-21 2-895-571-01 1-754-376-11 1-452-899-11 3-019-395-01 3-253-143-01 2-895-059-01 3-252-833-01 3-831-441-11
Description PANEL (UPPER) (G770CP/G770CPK) PANEL (UPPER) (G700CP) SPRING, CASSETTE LID, CASSETTE (G770CPK) LID, CASSETTE (G700CP) LID, CASSETTE (G770CP) LID, CD ANTENNA, TELESCOPIC MAGNET PLATE, CHUCKING SCREW (B2.6), (+) P TAPPING SPRING, CD SCREW (M3), (+) P CUSHION (B)
Remark
Ref. No. 212 213 214 215 216 217 218 219 220 220 221 SW2
Part No.
Description
Remark
3-047-468-21 DAMPER 2-895-586-01 A-1244-299-A 3-252-827-01 A-1244-298-A 2-895-587-01 3-047-468-01 3-254-143-11 2-895-566-01 2-895-566-11 2-895-760-01 BUTTON, CD CD KEY BOARD, COMPLETE SCREW (B2.6), (+) BV TAPPING WOOFER KEY BOARD, COMPLETE BUTTON, SOUND DAMPER SCREW (B3), (+) BV TAPPING CABINET (UPPER) (G770CP/G770CPK) CABINET (UPPER) (G700CP) SHEET (X PLOD)
1-692-960-11 SWITCH, PUSH (1 KEY) (Z PUSH OPEN/CLOSE)
55
8-6.
TAPE MECHANISM DECK SECTION
255
not supplied not supplied not supplied
256
257
not supplied not supplied
254 254
258
not supplied
252
253
251
not supplied
Ref. No. 251 252 253 254 255
Part No. 2-670-389-01 2-670-390-01 1-797-375-11 3-254-029-01 3-254-022-01
Description BELT (1) BELT (2) DECK, MECHANICAL (H21SB-C05) SCREW SCREW
Remark
Ref. No. 256 257 258
Part No.
Description
Remark
A-1246-280-A TC BOARD, COMPLETE 2-659-455-01 HOLDER (REC) 3-252-612-01 LEVER, REC
56
CFD-G700CP/G770CP/G770CPK SECTION 9 ELECTRICAL PARTS LIST

NOTE: Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX and -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. Accessories are given in the last of this parts list. CAPACITORS uF: F COILS uH: H Ref. No. Part No. Description RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable SEMICONDUCTORS In each case, u: , for example: uA. . : A. . uPA. . : PA. . uPB. . : PB. . uPC. . : PC. . uPD. . : PD. . Abbreviation AUS : Australian model CND : Canadian model E41 : AC 230V area in E model E92 : AC 120V area in E model MX : Mexican model SP : Singapore model Remark Ref. No. C105 C106 C107 C108 C109 C110 C112 C113 C115 C116 C117 C118 C119 C120 C122 C123 C124 C125 C126 C127 C128 C130 C132 C133 C136 C137 C138 C139 C140 C141 C142 C143 C144 C145 C146 C147 C148 C149 C150 C151 C152 C153 C201 Part No. 1-164-360-11 1-128-995-21 1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11 1-124-778-00 1-164-360-11 1-164-227-11 1-162-970-11 1-164-227-11 1-162-970-11 1-164-315-11 1-164-315-11 1-162-968-11 1-162-968-11 1-107-826-11 1-162-966-11 1-162-910-11 1-162-910-11 1-164-360-11 1-107-826-11 1-162-923-11 1-162-970-11 1-164-315-11 1-162-970-11 1-162-970-11 1-162-966-11 1-107-826-11 1-162-970-11 1-107-826-11 1-162-970-11 1-164-315-11 1-107-826-11 1-162-923-11 1-162-919-11 1-162-964-11 1-164-315-11
AUDIO IN
BATTERY BD90
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
Description CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 100uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 22uF 0.1uF 0.022uF 0.01uF 0.022uF 0.01uF 470PF 470PF 0.0047uF 0.0047uF 0.1uF 0.0022uF 5PF 5PF 0.1uF 0.1uF 47PF 0.01uF 470PF 0.01uF 0.01uF 0.0022uF 0.1uF 0.01uF 0.1uF 0.01uF 470PF 0.1uF 47PF 22PF 0.001uF 470PF 470PF 0.1uF 100uF 20%
Remark 16V 10V 16V 16V 16V 16V 16V 16V 6.3V 16V 25V 25V 25V 25V 50V 50V 50V 50V 16V 50V
A-1244-296-A AUDIO IN BOARD, COMPLETE ************************ < CONNECTOR > CNP357 1-815-551-11 PIN, CONNECTOR (PWB) 3P < JACK > J402 1-815-629-11 JACK (AUDIO IN) < JUMPER RESISTOR > JR205 JR206 1-216-864-11 SHORT CHIP 1-216-864-11 SHORT CHIP < COIL > L101 L102 L202 1-410-517-11 INDUCTOR 1-410-517-11 INDUCTOR 1-410-517-11 INDUCTOR < RESISTOR > R121 1-216-837-11 METAL CHIP 22K 5% 1/10W R122 1-216-837-11 METAL CHIP 22K 5% 1/10W R221 1-216-837-11 METAL CHIP 22K 5% 1/10W R222 1-216-837-11 METAL CHIP 22K 5% 1/10W ************************************************************* A-1244-301-A BATTERY BOARD, COMPLETE ************************ 3-238-135-01 TERMINAL (), BATTERY < CONNECTOR > CNP941 1-815-552-11 PIN, CONNECTOR (PWB) 4P ************************************************************* A-1244-423-A BD90 BOARD, COMPLETE ******************** < CAPACITOR > C100 C101 C102 C103 C104 1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11 1-164-360-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 16V 16V 16V 16V 16V 47uH 47uH 47uH 0 0
20%
10% 10% 10% 10% 5% 5% 10% 10% 10% 10%
0.25PF 50V 0.25PF 50V 16V 10% 16V 5% 50V 10% 5% 10% 10% 10% 10% 10% 10% 10% 5% 10% 5% 5% 10% 5% 5% 20% 25V 50V 25V 25V 50V 16V 25V 16V 25V 50V 16V 50V 50V 50V 50V 50V 16V 10V
1-164-315-11 CERAMIC CHIP 1-164-360-11 CERAMIC CHIP 1-128-995-21 ELECT CHIP
57
BD90
Ref. No. C202 C204 C205 C206 C207 C301 C302 C303 C306 C307 C309 C401 C403 C404 C405
CD KEY
Part No. Description 100uF 0.1uF 0.1uF 1uF 1uF 0.1uF 10uF 10uF 100uF 1uF 0.001uF 220uF 0.1uF 0.1uF 0.1uF 20% Remark 10V 16V 16V 10V 10V 16V 6.3V 6.3V 10V 10V 50V 10V 16V 16V 16V Ref. No. R146 R147 R148 R149 R150 R151 R153 R154 R155 R156 R157 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R211 R212 R218 R219 R220 R221 R222 R223 R301 R302 R303 R304 R402 R405 R408 R414 R415 Part No. Description 0 0 0 0 0 0 1M 1M 47 100 100 0 0 100 100 100 100 100 100 100 100 100 100 100K 100K 100K 100K 100K 100K 100K 0 2.2 2.2 2.2K 10K 2.2K 4.7K 47K Remark
1-128-995-21 ELECT CHIP 1-164-360-11 CERAMIC CHIP 1-164-360-11 1-165-908-11 1-165-908-11 1-164-360-11 1-137-710-91 1-137-710-91 1-128-995-21 1-165-908-11 1-162-964-11 1-128-394-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP
1-216-864-11 SHORT CHIP 1-216-864-11 SHORT CHIP 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-857-11 1-216-857-11 1-216-805-11 1-216-809-11 1-216-809-11 1-216-295-91 1-216-295-91 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-864-11 1-216-789-11 1-216-789-11 1-216-825-11 1-216-833-11 1-216-825-11 1-216-829-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10% 10% 20% 20% 20% 10% 10% 20%
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
1-164-360-11 CERAMIC CHIP 1-164-360-11 CERAMIC CHIP 1-164-360-11 CERAMIC CHIP < CONNECTOR >
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
CN201 CN301
1-784-833-51 CONNECTOR, FFC (LIF (NON-ZIF)) 21P 1-770-425-51 CONNECTOR, FFC/FPC 16P < IC >
IC101 IC201 IC401
(Not supplied) IC TC94A70FG-006 6-710-808-01 IC TK63115SCL-G@GT 6-710-637-01 IC BA5826SFP-E2 < TRANSISTOR >
Q301
6-551-120-01 TRANSISTOR < RESISTOR >
2SA2119K
R101 R102 R104 R105 R106 R108 R110 R111 R112 R113 R114 R118 R120 R125 R126 R127 R128 R129 R130 R134 R135 R136 R139 R140 R142 R143 R144 R145
1-216-813-11 1-216-833-11 1-216-295-91 1-216-857-11 1-216-821-11 1-216-864-11 1-216-833-11 1-216-809-11 1-216-809-11 1-216-833-11 1-216-833-11 1-216-845-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-853-11 1-216-821-11 1-216-829-11 1-216-857-11 1-216-853-11 1-216-837-11 1-216-841-11 1-216-864-11 1-216-837-11
METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP
220 10K 0 1M 1K 0 10K 100 100 10K 10K 100K 0 0 0 0 470K 1K 4.7K 1M 470K 22K 47K 0 22K 47K 22K 0
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
5% 5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
1-216-841-11 METAL CHIP < VIBRATOR >
X102 1-795-101-21 VIBRATOR, CERAMIC (16.934MHz) ************************************************************* A-1244-299-A CD KEY BOARD, COMPLETE ***********************
5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W R421 R422 R466 R404 R405 R406 R407 R410
3-831-441-11 CUSHION (B) < RESISTOR > 1-216-821-11 1-216-825-11 1-216-821-11 1-216-825-11 1-216-813-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 2.2K 1K 2.2K 220 470 1K 100 5% 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
1-216-841-11 METAL CHIP 1-216-837-11 METAL CHIP 1-216-864-11 SHORT CHIP
1-216-817-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-809-11 METAL CHIP
58
CD KEY LED1
Ref. No. Part No. Description < SWITCH > S401 S402 S405 S406 S413 1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21 SWITCH, KEY BOARD (TUNE / ) SWITCH, KEY BOARD (TUNE +/ +) SWITCH, KEY BOARD (u) SWITCH, KEY BOARD (x) SWITCH, KEY BOARD (PRESET .) Remark Ref. No. Part No.
D-LIGHT LED2
Description
HEADPHONE LED3 LED4
LCD MAIN
Remark
< LIQUID CRYSTAL DISPLAY > LCD401 1-802-396-11 DISPLAY PANEL, LIQUID CRYSTAL < RESISTOR > R428 1-216-813-11 METAL CHIP 220 5% 1/10W R469 1-216-845-11 METAL CHIP 100K 5% 1/10W R475 1-216-849-11 METAL CHIP 220K 5% 1/10W ************************************************************* A-1243-618-A LED1 BOARD, COMPLETE ******************** < RESISTOR > R471 1-216-813-11 METAL CHIP 220 5% 1/10W R472 1-216-813-11 METAL CHIP 220 5% 1/10W ************************************************************* A-1243-619-A LED2 BOARD, COMPLETE ******************** < RESISTOR > R449 1-216-813-11 METAL CHIP 220 5% 1/10W R450 1-216-813-11 METAL CHIP 220 5% 1/10W ************************************************************* A-1243-620-A LED3 BOARD, COMPLETE ******************** < RESISTOR > R476 1-216-813-11 METAL CHIP 220 5% 1/10W R487 1-216-813-11 METAL CHIP 220 5% 1/10W ************************************************************* 10uH A-1243-621-A LED4 BOARD, COMPLETE ******************** < RESISTOR >
S414 1-786-050-21 SWITCH, KEY BOARD (PRESET + >) ************************************************************* A-1244-302-A D-LIGHT BOARD, COMPLETE (G700CP) *********************** < JACK > J103 1-820-048-11 CONNECTOR (LIGHTING) (D-LIGHT SYNC OUT) < RESISTOR > L302 1-216-864-11 SHORT CHIP 0 L306 1-216-864-11 SHORT CHIP 0 L307 1-216-864-11 SHORT CHIP 0 ************************************************************* A-1244-297-A HEADPHONE BOARD, COMPLETE *************************** < CONNECTOR > CNP392 1-815-552-11 PIN, CONNECTOR (PWB) 4P < JACK > J391 1-794-016-11 JACK (i) < COIL > L301 1-410-509-11 INDUCTOR < RESISTOR > R192 R193 R194 R292 R293 1-216-821-11 1-216-813-11 1-216-813-11 1-216-821-11 1-216-813-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 220 220 1K 220 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W
R478 1-216-813-11 METAL CHIP 220 5% 1/10W R479 1-216-813-11 METAL CHIP 220 5% 1/10W ************************************************************* A-1244-300-A A-1244-370-A A-1244-371-A A-1244-372-A A-1244-373-A A-1244-374-A MAIN BOARD, COMPLETE (MX, E92) MAIN BOARD, COMPLETE (G700CP) MAIN BOARD, COMPLETE (CND) MAIN BOARD, COMPLETE (SP) MAIN BOARD, COMPLETE (E41) MAIN BOARD, COMPLETE (AUS) *********************
R294 1-216-813-11 METAL CHIP 220 5% 1/10W ************************************************************* A-1244-292-A LCD BOARD, COMPLETE ******************** 1-831-799-21 CABLE, FLEXIBLE FLAT (19 CORE) 2-895-582-01 HOLDER, LCD 3-198-120-01 SHEET (IR), ADHESIVE < CAPACITOR >
1-832-425-21 CABLE, FLEXIBLE FLAT (11 CORE) 1-833-945-21 CABLE, FLEXIBLE FLAT (11 CORE) 3-252-827-01 SCREW (B2.6), (+) BV TAPPING < CAPACITOR >
C401
1-115-156-11 CERAMIC CHIP < DIODE >
1uF
10V C106 C107 C108 C109 C110 C111 C121 1-107-826-11 1-107-826-11 1-165-176-11 1-165-176-11 1-162-968-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.047uF 0.047uF 0.0047uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 50V 50V 50V
D406
8-719-059-97 DIODE L-34HD (OPR/BATT) < IC >
IC891
6-701-681-01 IC RPM7140-V4
1-162-966-11 CERAMIC CHIP 1-126-960-11 ELECT
0.0022uF 10% 1uF 20%
59
MAIN
Ref. No. C123 C124 C125 C126 C127 C131 C132 C151 Part No. Description 2.2uF 100PF 4.7uF 2.2uF 1uF 0.47uF 100PF 10uF 20% 5% 20% 20% 20% 20% 5% 20% Remark 50V 50V 50V 50V 50V 50V 50V 50V (G770CPK) Ref. No. C326 C327 C332 C333 C334 C335 C336 C337 C338 C339 C340 C341 C342 C343 C344 Part No. Description 0.047uF 0.022uF 1uF 0.01uF 0.022uF 1uF 220uF 1uF 10uF 100uF 100uF 22uF 100PF 10uF 10uF 10% 10% 20% 10% 10% 20% 20% 20% 20% 20% 20% 20% 5% 20% 20% Remark 16V 25V 50V (G700CP) 25V 25V 50V 10V 50V (G700CP) 50V 10V 10V 25V 50V 50V 50V (G700CP) 50V 25V 50V 25V 25V 50V 10V 16V 10V 10V 10V 10V 25V 25V 25V 50V 25V 50V 50V 10V
1-126-961-11 ELECT 1-162-927-11 CERAMIC CHIP 1-126-963-11 ELECT 1-126-961-11 1-126-960-11 1-126-959-11 1-162-927-11 1-126-964-11 ELECT ELECT ELECT CERAMIC CHIP ELECT
1-165-176-11 CERAMIC CHIP 1-164-227-11 CERAMIC CHIP 1-126-960-11 ELECT 1-162-970-11 CERAMIC CHIP 1-164-227-11 CERAMIC CHIP 1-126-960-11 ELECT 1-126-923-91 ELECT 1-126-960-11 ELECT 1-126-964-11 ELECT 1-104-658-91 ELECT 1-104-658-91 1-104-662-91 1-162-927-11 1-126-964-11 1-126-964-11 ELECT ELECT CERAMIC CHIP ELECT ELECT
C152 C153 C153 C154 C161 C171 C172 C173 C174 C175 C206 C207 C208 C209 C210 C211 C221 C223 C224 C225 C226 C227 C231 C232 C251
1-126-960-11 ELECT 1-126-960-11 ELECT 1-126-964-11 ELECT 1-162-960-11 CERAMIC CHIP 1-126-960-11 ELECT 1-126-947-11 1-162-962-11 1-104-658-91 1-126-926-11 1-164-156-11 1-107-826-11 1-107-826-11 1-165-176-11 1-165-176-11 1-162-968-11 1-162-966-11 1-126-960-11 1-126-961-11 1-162-927-11 1-126-963-11 1-126-961-11 1-126-960-11 1-126-959-11 1-162-927-11 1-126-964-11 ELECT CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT ELECT ELECT ELECT CERAMIC CHIP ELECT
1uF 1uF 10uF 220PF 1uF 47uF 470PF 100uF 1000uF 0.1uF 0.1uF 0.1uF 0.047uF 0.047uF 0.0047uF 0.0022uF 1uF 2.2uF 100PF 4.7uF 2.2uF 1uF 0.47uF 100PF 10uF
50V (G770CPK) 20% 50V (MX, E92, AUS) 20% 50V (CND) 10% 50V (G770CPK) 20% 50V 20% 10% 20% 20% 35V 50V 10V 10V 25V 16V 16V 16V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V (G770CPK)
20%
C345 C346 C347 C348 C349 C350 C351 C352 C353 C354 C355 C356 C357 C358 C359 C360 C361 C362 C366 C371 C380 C381 C402 C411 C415
1-126-964-11 1-126-942-61 1-126-964-11 1-126-946-11 1-104-666-11 1-162-995-11 1-104-658-91 1-107-826-11 1-104-658-91 1-104-658-91 1-104-658-91 1-104-658-91 1-164-156-11 1-164-156-11 1-104-662-91 1-126-961-11 1-162-970-11 1-126-964-11 1-162-927-11 1-104-658-91
ELECT ELECT ELECT ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT
10uF 1000uF 10uF 6800uF 220uF 0.022uF 100uF 0.1uF 100uF 100uF 100uF 100uF 0.1uF 0.1uF 22uF 2.2uF 0.01uF 10uF 100PF 100uF 220uF 100uF 1uF 100PF 0.022uF
20% 20% 20% 20% 20%
10% 10% 10% 10% 10% 10% 20% 20% 5% 20% 20% 20% 20% 5% 20%
20% 10% 20% 20% 20% 20%
20% 20% 10% 20% 5% 20% 20% 20%
C252 C253 C253 C254 C261 C271 C272 C273 C274 C275 C301 C302 C303 C304 C305
1-126-960-11 ELECT 1-126-960-11 ELECT 1-126-964-11 ELECT 1-162-960-11 CERAMIC CHIP 1-126-960-11 ELECT 1-126-947-11 1-162-962-11 1-104-658-91 1-126-926-11 1-164-156-11 ELECT CERAMIC CHIP ELECT ELECT CERAMIC CHIP
1uF 1uF 10uF 220PF 1uF 47uF 470PF 100uF 1000uF 0.1uF 220uF 1uF 10uF 0.1uF 470uF
50V (G770CPK) 20% 50V (MX, E92, AUS) 20% 50V (CND) 10% 50V (G770CPK) 20% 50V 20% 10% 20% 20% 35V 50V 10V 10V 25V
20%
1-126-923-91 ELECT 1-104-658-91 ELECT 1-126-960-11 ELECT 1-162-927-11 CERAMIC CHIP 1-164-227-11 CERAMIC CHIP
10V 10V (G700CP) 20% 50V (G770CPK) 5% 50V 10% 25V (G770CPK) 20% 20% 20% 20% 20% 10V (G770CPK) 50V (G770CPK) 50V (G770CPK) 10V (G770CPK) 35V (G770CPK)
C416 C417 C418 C419 C420
1-104-658-91 ELECT 1-126-963-11 ELECT 1-126-963-11 ELECT 1-104-658-91 ELECT 1-126-947-11 ELECT
100uF 4.7uF 4.7uF 100uF 47uF
1-126-923-91 ELECT 1-115-156-11 1-126-964-11 1-107-826-11 1-126-935-11 CERAMIC CHIP ELECT CERAMIC CHIP ELECT
10V (G770CPK) 10V 20% 50V 10% 16V 20% 16V
20%
C421 C422
1-126-960-11 ELECT 1-126-947-11 ELECT
1uF 47uF
20%
50V (G770CPK) 20% 35V (G770CPK)
60
MAIN
Ref. No. C423 C424 C425 Part No. Description 22uF 10uF 0.22uF 20% Remark 25V (G770CPK) 20% 50V (G770CPK) 10% 16V (G770CPK) 16V (G770CPK) 20% 50V (G770CPK) 10V 5% 50V (G770CPK) 5% 50V (G770CPK) 5% 50V (G770CPK) 25V 10% 25V 0.5PF 50V 5% 50V 5% 5% 5% 10% 10% 0.5PF 20% 10% 20% 50V 50V 50V 25V 25V 50V 50V 25V 25V 10V 10V 25V 10V 25V 16V 16V 16V 50V 16V 16V 10V 50V 50V 50V 50V (G770CPK) 50V 50V 50V 50V 50V 50V 50V 50V 25V 25V 25V 25V 10% Ref. No. C851 C852 C853 C854 C855 C856 C857 C951 C953 C954 C955 C957 C961 C962 C433 C436 C437 C451 C453 C454 C455 C456 C457 C458 C459 C461 C803 C804 C805 C806 C807 C808 C810 C813 C814 C815 C816 C819 C820 C825 C826 C827 C828 C829 1-162-927-11 CERAMIC CHIP 1-164-156-11 1-100-591-91 1-162-913-11 1-162-919-11 1-162-923-11 1-162-923-11 1-162-919-11 1-162-970-11 1-162-970-11 1-162-915-11 1-126-964-11 1-164-156-11 1-162-970-11 1-104-658-91 1-115-156-11 1-162-970-11 1-104-658-91 1-162-970-11 1-107-826-11 1-107-826-11 1-107-826-11 1-162-927-11 1-107-826-11 1-107-826-11 1-115-156-11 1-162-964-11 1-162-968-11 1-162-964-11 1-162-927-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 0.1uF 1uF 8PF 22PF 47PF 47PF 22PF 0.01uF 0.01uF 10PF 10uF 0.1uF 0.01uF 100uF 1uF 0.01uF 100uF 0.01uF 0.1uF 0.1uF 0.1uF 100PF 0.1uF 0.1uF 1uF 0.001uF 0.0047uF 0.001uF 100PF Part No. Description 100PF 100PF 100PF 100PF 100PF 100PF 100PF 0.022uF 0.022uF 220uF 0.022uF 220uF 220uF 0.022uF 5% 5% 5% 5% 5% 5% 5% 10% 10% 20% 10% 20% 20% 10% Remark 50V 50V 50V 50V 50V 50V 50V 25V 25V 16V 25V 10V 10V 25V (G700CP)
1-104-662-91 ELECT 1-126-964-11 ELECT 1-127-715-91 CERAMIC CHIP
1-162-927-11 CERAMIC CHIP 1-162-927-11 CERAMIC CHIP 1-162-927-11 CERAMIC CHIP 1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11 1-164-227-11 1-164-227-11 1-126-934-11 1-164-227-11 1-126-923-91 1-126-923-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT
C426 C427 C430 C431 C432
1-127-715-91 CERAMIC CHIP 1-126-963-11 ELECT 1-115-156-11 CERAMIC CHIP 1-162-927-11 CERAMIC CHIP 1-162-927-11 CERAMIC CHIP
0.22uF 4.7uF 1uF 100PF 100PF
1-164-227-11 CERAMIC CHIP
< CONNECTOR > * CN799 CN803 CN804 CN805 1-784-732-11 1-784-741-11 1-784-741-11 1-779-289-11 CONNECTOR, FFC 10P CONNECTOR, FFC 19P CONNECTOR, FFC 19P CONNECTOR, FFC (LIF (NON-ZIF)) 21P < CONNECTOR > CNP301 CNP303 CNP390 CNP391 CNP393 CNP394 CNP397 CNP803 CNP805 CNP806 1-815-553-21 1-815-554-11 1-815-554-11 1-815-553-11 1-815-552-11 1-815-551-11 1-815-551-11 1-815-550-31 1-815-551-11 1-815-550-21 PIN, CONNECTOR (PWB) 5P PIN, CONNECTOR (PWB) 6P PIN, CONNECTOR (PWB) 6P (G770CPK) PIN, CONNECTOR (PWB) 5P PIN, CONNECTOR (PWB) 4P PIN, CONNECTOR (PWB) 3P PIN, CONNECTOR (PWB) 3P (G700CP) PIN, CONNECTOR (PWB) 2P PIN, CONNECTOR (PWB) 3P PIN, CONNECTOR (PWB) 2P
10% 20% 10% 10% 10% 10% 5% 10% 10%
CNP807 1-815-550-11 PIN, CONNECTOR (PWB) 2P < DIODE > D320 D321 D322 D323 D324 D351 D414 D415 D461 D462 D801 D802 D804 D805 D951 D952 D953 D954 D955 6-500-335-01 6-501-193-01 6-501-193-01 6-501-193-01 6-500-335-01 6-501-579-01 6-501-193-01 6-500-334-01 6-500-335-01 8-719-069-54 6-500-334-01 6-500-334-01 6-501-193-01 6-501-193-01 6-501-193-01 6-500-334-01 6-501-193-01 8-719-977-28 8-719-978-33 DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE MC2838-T112-1 1SS355WTE-17 1SS355WTE-17 1SS355WTE-17 MC2838-T112-1 MC2837 1SS355WTE-17 (G770CPK) MC2836-T112-1 (G770CPK) MC2838-T112-1 UDZSTE-175.1B MC2836-T112-1 MC2836-T112-1 1SS355WTE-17 (G770CPK) 1SS355WTE-17 1SS355WTE-17 MC2836-T112-1 1SS355WTE-17 DTZ10B DTZ-TT11-6.8B
10% 10% 10% 5%
C831 C833 C837 C839 C841 C842 C843 C846 C847 C848 C849 C850
1-162-927-11 1-162-927-11 1-162-927-11 1-164-230-11 1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11 1-162-970-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100PF 100PF 100PF 220PF 100PF 100PF 100PF 100PF 0.01uF 0.01uF 0.01uF 0.01uF
5% 5% 5% 5% 5% 5% 5% 5% 10% 10% 10% 10%
1-162-970-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP
61
MAIN
Ref. No. Part No. Description < FERRITE BEAD > FB831 FB832 FB833 FB834 FB835 FB836 FB837 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-414-760-21 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 SHORT CHIP 0 FERRITE, EMI (SMD) (1608) Remark Ref. No. L159 L160 L803 Part No. Description 2.2uH 2.2uH 47uH Remark
1-410-501-11 INDUCTOR 1-410-501-11 INDUCTOR 1-414-743-21 INDUCTOR < TRANSISTOR >
1-414-760-21 FERRITE, EMI (SMD) (1608) 1-216-864-11 SHORT CHIP 0 < IC >
Q171 Q271 Q320 Q321 Q322 Q323 Q351 Q352 Q354 Q401
8-729-620-07 TRANSISTOR 8-729-620-07 TRANSISTOR 8-729-620-07 TRANSISTOR 8-729-620-07 TRANSISTOR 8-729-620-07 TRANSISTOR 8-729-045-62 8-729-036-89 6-551-443-01 8-729-036-86 8-729-620-07 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SC3052EF-T1-LEF 2SC3052EF-T1-LEF 2SC3052EF-T1-LEF (G700CP) 2SC3052EF-T1-LEF 2SC3052EF-T1-LEF 2SK2158-T2B KTC3198GR-AT RT1P436C-TP-1 KTC3203Y-AT 2SC3052EF-T1-LEF (G770CPK) 2SC3052EF-T1-LEF (G770CPK) DTC114YKA-T146 (G770CPK) 2SC3052EF-T1-LEF (G770CPK) DTC114YKA-T146 (G770CPK) DTC114YKA-T146 (G770CPK) 2SC3052EF-T1-LEF 2SC3052EF-T1-LEF DTC114YKA-T146 2SC3052EF-T1-LEF DTC114YKA-T146 ISA1235AC1TP-1EF RT1N436C-TP-1 (SP, E41, AUS) DTC114YKA-T146 DTA114YKA-T146 KTA1271Y KTA1271Y DTC123JKA-T146 ISA1235AC1TP-1EF RT1N431C-TP-1 KTC3203Y-AT DTC114YKA-T146 KTD2058Y KTD2058Y
IC321 IC351 IC371 IC401 IC801 IC802 IC805 IC806 IC901 IC902
6-710-289-01 8-759-426-51 8-759-426-51 8-759-332-64 6-807-359-01 6-710-820-01 6-704-118-01 6-706-338-01 6-710-863-01 6-702-771-01
IC IC IC IC IC IC IC IC IC IC
R2S15904SP BA5417 BA5417 BA3837 (G770CPK) MB90802NPF-G-127E1 S-24CS02AFJ-TB-G S-80828CNMC-B8NT2G XC6202P332FR TK70540SCL-G (G700CP) TA78033LS
Q402 Q403 Q405
8-729-620-07 TRANSISTOR 8-729-027-46 TRANSISTOR 8-729-620-07 TRANSISTOR 8-729-027-46 TRANSISTOR 8-729-027-46 TRANSISTOR
< JUMPER RESISTOR > Q406 JR105 JR106 JR107 JR108 JR109 JR110 JR111 JR113 JR114 JR117 JR118 JR120 JR121 JR122 JR124 JR126 JR127 JR128 JR129 JR131 JR133 JR134 JR135 JR136 JR137 JR138 JR140 JR150 JR151 JR152 JR153 JR155 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Q407
Q451 Q452 Q801 Q803 Q804 Q805 Q806 Q812 Q815 Q816 Q950 Q951 Q952 Q953 Q954 Q959 Q971 Q972
8-729-620-07 8-729-620-07 8-729-027-46 8-729-620-07 8-729-027-46
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
6-551-696-01 TRANSISTOR 6-551-444-01 TRANSISTOR 8-729-027-46 TRANSISTOR 8-729-027-26 TRANSISTOR 8-729-037-13 TRANSISTOR 8-729-037-13 8-729-027-50 6-551-696-01 6-551-276-01 8-729-036-86 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
8-729-027-46 TRANSISTOR 8-729-037-08 TRANSISTOR 8-729-037-08 TRANSISTOR < RESISTOR >
R101 R102 R103 R104 R120 R123 R124 R125 R126 R127
1-216-864-11 1-216-833-11 1-216-841-11 1-216-829-11 1-216-829-11 1-216-829-11 1-216-864-11 1-216-837-11 1-216-841-11
SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP
0 (G700CP/G770CP) 10K 5% 1/10W 47K 5% 1/10W 4.7K 5% 1/10W 4.7K 5% 1/10W 4.7K 0 22K 47K 10K 5% 5% 5% 5% 1/10W 1/10W 1/10W (G700CP) 1/10W
1-216-864-11 SHORT CHIP 1-216-864-11 SHORT CHIP < COIL >
1-216-833-11 METAL CHIP
L158
1-410-501-11 INDUCTOR
2.2uH
62
MAIN
Ref. No. R129 R130 R135 R151 R151 R152 R153 R154 R160 R161 R162 R172 R173 R175 R176 R179 R181 R201 R202 R203 R204 R220 R223 R224 R225 R226 R227 R229 R230 R235 R251 R251 R252 R253 R254 Part No. 1-216-864-11 1-216-841-11 1-216-864-11 1-216-833-11 Description SHORT CHIP METAL CHIP SHORT CHIP METAL CHIP 0 47K 0 10K 5% 5% Remark 1/10W Ref. No. R325 R326 R328 R329 R330 R331 R332 R333 R334 R335 R336 R337 R338 R339 R340 R341 R342 R343 R344 R345 R346 R347 1-216-829-11 1-216-829-11 1-216-829-11 1-216-864-11 1-216-837-11 METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP 4.7K 4.7K 4.7K 0 22K 47K 10K 0 47K 0 10K 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W (G700CP) 1/10W 1/10W R348 R351 R353 R356 R357 R359 R360 R361 R362 R363 R364 R365 R366 R371 R372 R409 R418 R419 R261 R262 R272 R273 R275 R276 R279 R281 R317 R318 1-216-821-11 1-216-864-11 1-216-833-11 1-216-825-11 1-216-813-11 1-216-801-11 1-216-829-11 1-216-793-11 1-216-833-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 0 10K 2.2K 220 22 4.7K 4.7 10K 470K 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W (G700CP) 1/10W (G700CP) 1/10W (G700CP) 1/10W R420 R427 R429 R430 R431 R432 R433 1-216-829-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-825-11 METAL CHIP 1-216-841-11 METAL CHIP 1-216-817-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-841-11 METAL CHIP 4.7K 1K 2.2K 47K 470 1K 47K 5% 5% 5% 5% 5% 5% 5% Part No. Description 2.2K 1K 1K 2.2K 470 22K 470K 10K 470 22K 10K 22K 2.2K 1K 1K 4.7K 2.2K 2.2K 4.7K 470 47 470K 4.7K 4.7K 4.7K 1K 470 10 10 2.2K 470 220 1M 1M 10K 10K 10K 1K 1K 47K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W (G700CP) 1/10W (G700CP) 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W (G770CPK) 1/10W (G770CPK) 1/10W 1/10W 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK)
1-216-825-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-821-11 1-216-825-11 1-216-817-11 1-216-837-11 1-216-853-11 1-216-833-11 1-216-817-11 1-216-837-11 1-216-833-11 1-216-837-11 1-216-825-11 1-216-821-11 1-216-821-11 1-216-829-11 1-216-825-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1-216-864-11 SHORT CHIP 1-216-829-11 METAL CHIP 1-216-829-11 METAL CHIP 1-216-833-11 METAL CHIP 1-216-841-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-841-11 1-216-833-11 1-216-825-11 1-216-813-11 1-216-801-11 1-216-829-11 1-216-793-11 1-216-864-11 1-216-833-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP
1/10W (G770CPK) 0 (G700CP/G770CP) 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
4.7K 4.7K 10K 47K 1K 47K 10K 2.2K 220 22
4.7K 5% 1/10W 4.7 5% 1/10W 0 (G700CP/G770CP) 10K 5% 1/10W 47K 5% 1/10W
1-216-825-11 METAL CHIP 1-216-829-11 METAL CHIP 1-216-817-11 METAL CHIP 1-216-805-11 METAL CHIP 1-216-853-11 METAL CHIP 1-216-829-11 1-216-829-11 1-216-829-11 1-216-821-11 1-216-817-11 1-216-797-11 1-216-797-11 1-216-825-11 1-216-817-11 1-216-813-11 1-216-857-11 1-216-857-11 1-216-833-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1-216-841-11 METAL CHIP 1-216-833-11 1-216-864-11 1-216-841-11 1-216-864-11 METAL CHIP SHORT CHIP METAL CHIP SHORT CHIP
1-216-833-11 METAL CHIP 1-216-864-11 SHORT CHIP 1-216-829-11 METAL CHIP 1-216-829-11 METAL CHIP 1-216-833-11 METAL CHIP
1/10W (G770CPK) 0 (G700CP/G770CP) 4.7K 5% 1/10W (G770CPK) 4.7K 5% 1/10W (G770CPK) 10K 5% 1/10W (G770CPK)
5%
1-216-853-11 METAL CHIP
R319 R322 R324
1-216-829-11 METAL CHIP 1-216-864-11 SHORT CHIP 1-216-825-11 METAL CHIP
4.7K 0 2.2K
5%
R434
1-216-821-11 METAL CHIP
1K
5%
5%
63
MAIN
Ref. No. R435 R436 R437 R438 Part No. Description 4.7K 2.2K 1K 1K 5% 5% 5% 5% Remark 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W (G770CPK) 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W (G770CPK) 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W (G770CPK) Ref. No. R807 R808 R809 R810 R811 R812 R813 R814 R815 R816 R817 R818 R819 R820 R821 R822 R823 R824 R825 R826 R826 R827 R453 R454 R456 R457 R460 R461 R462 R463 R468 R470 1-216-821-11 1-216-833-11 1-216-821-11 1-216-833-11 1-216-813-11 1-216-817-11 1-216-817-11 1-216-813-11 1-216-821-11 1-216-817-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 10K 1K 10K 220 470 470 220 1K 470 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% R827 Part No. Description 4.7K 1K 1K 4.7K 10K 1K 1K 1K 1K 1K 1K 1K 1K 470K 1K 1K 1K 1K 1K 2.2K 4.7K 2.2K 4.7K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W (E41) 1/10W (SP, AUS) 1/10W (SP) 1/10W (E41, AUS) 1/10W 1/10W 1/10W 1/10W (G770CPK) 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
1-216-829-11 METAL CHIP 1-216-825-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-821-11 METAL CHIP
1-216-829-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-829-11 1-216-833-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-853-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
R439 R440 R441 R444 R445
1-216-817-11 METAL CHIP 1-216-817-11 METAL CHIP 1-216-849-11 METAL CHIP 1-216-845-11 METAL CHIP 1-216-829-11 METAL CHIP
470 470 220K 100K 4.7K
5% 5% 5% 5% 5%
R446 R447 R448 R451 R452
470 47K 1K 1K 1K
5% 5% 5% 5% 5%
R828 R829 R830 R831 R834 R835 R836 R837 R838 R839 R840 R841 R842 R843 R844 R845 R846 R847 R848 R849 R850 R851 R852 R853 R854 R855 R856 R857 R858 R859
1-216-829-11 1-216-829-11 1-216-829-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
4.7K 4.7K 4.7K 1K 10K 10K 10K 10K 10K 47K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K 10K
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1-216-833-11 METAL CHIP 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-841-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
R477 R480 R481 R482 R483 R484 R485 R486 R488 R489
1-216-845-11 1-216-841-11 1-216-841-11 1-216-821-11 1-216-841-11 1-216-841-11 1-216-841-11 1-216-845-11 1-216-837-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 47K 47K 1K 47K 47K 47K 100K 22K 47K
5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
R490 R491 R492 R493 R494
1-216-864-11 1-216-864-11 1-216-864-11 1-216-821-11 1-216-841-11
SHORT CHIP SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP
0 0 0 1K 47K
5% 5%
1/10W 1/10W (G770CPK) 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
R495 R800 R801 R802 R803 R804 R805
1-216-845-11 1-216-825-11 1-216-817-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 2.2K 470 1K 1K 1K 1K
5% 5% 5% 5% 5% 5% 5%
1-216-821-11 METAL CHIP 1-216-821-11 METAL CHIP
64
MAIN
Ref. No. R860 R861 R862 R863 R864 R865 R866 R867 R868 R869 Part No. 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-821-11 1-216-821-11 1-216-833-11 1-216-833-11 1-216-817-11 1-216-821-11 Description METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 10K 10K 1K 1K 10K 10K 470 1K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W (G770CPK) 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W (G770CPK) Ref. No. R946 R947 R948 R949 R950 R951 R952 R953 R954 R955 R957 R960 R961 R964 R965 R966 Part No. Description 2.2K 2.2K 2.2K 2.2K 2.2K 100K 2.2K 2.2K 100K 0 0 470 1K 100 10 10 5% 5% 5% 5% 5% 5% 5% 5% 5%
MICROPHONE
Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
1-216-825-11 METAL CHIP 1-216-825-11 METAL CHIP 1-216-825-11 METAL CHIP 1-216-825-11 1-216-825-11 1-216-845-11 1-216-825-11 1-216-825-11 1-216-845-11 1-216-864-11 1-216-864-11 1-216-817-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP
R870 R871 R872 R873 R874 R875 R876 R877 R878 R879 R880 R881 R882 R883 R884
1-216-821-11 1-216-817-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-813-11 1-216-821-11 1-216-821-11 1-216-833-11 1-216-821-11 1-216-833-11 1-216-833-11 1-216-821-11 1-216-817-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 470 1K 1K 1K 1K 220 1K 1K 10K 1K 10K 10K 1K 470
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
1-216-809-11 METAL CHIP 1-216-797-11 METAL CHIP 1-216-797-11 METAL CHIP < VIBRATOR >
X802 1-813-940-11 PIEZOELECTRIC OSCILLATOR (5.53MHz) ************************************************************* A-1244-295-A MICROPHONE BOARD, COMPLETE (G770CPK) **************************** < CAPACITOR > C408 C414 1-165-176-11 CERAMIC CHIP 1-162-968-11 CERAMIC CHIP < DIODE > D401 8-719-059-97 DIODE L-34HD (KARAOKE PON) < JACK > J401 1-815-629-11 JACK (MIC MIX) < COIL > L303 L304 L305 L308 1-410-509-11 1-410-517-11 1-410-509-11 1-410-509-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR < RESISTOR > R426 R464 R465 R473 1-216-821-11 1-216-825-11 1-216-825-11 1-216-829-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 2.2K 2.2K 4.7K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 10uH 47uH 10uH 10uH 0.047uF 10% 0.0047uF 10% 16V 50V
R885 R886 R887 R888 R888
1K 47K 47K 10K 47K
1/10W 1/10W 1/10W (G770CPK) 5% 1/10W (G700CP/G770CP) 5% 1/10W (G770CPK)
5% 5% 5%
R891 R892 R893 R894 R895
1-216-841-11 1-216-864-11 1-216-864-11 1-216-797-11 1-216-797-11
METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP
47K 5% 1/10W 0 0 (G700CP/G770CP) 10 5% 1/10W 10 5% 1/10W (G770CPK) 10K 100 4.7K 100 47K 47K 1K 1K 1K 1K 1K 10K 2.2K 2.2K 2.2K 2.2K 2.2K 5% 1/10W 5% 1/10W 5% 1/10W (US, CND, MX, E92) 5% 1/10W 5% 1/10W 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
R896 R897 R898 R899 R900 R901 R902 R903 R904 R905 R906 R907 R941 R942 R943 R944 R945
1-216-833-11 METAL CHIP 1-216-809-11 METAL CHIP 1-216-829-11 METAL CHIP 1-216-809-11 METAL CHIP 1-216-841-11 METAL CHIP 1-216-841-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-833-11 1-216-825-11 1-216-825-11 1-216-825-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
< VARIABLE RESISTOR > RV401 1-227-757-11 RES, VAR, CARBON < SWITCH > S422 1-572-006-11 SWITCH, PUSH (1 KEY) (KARAOKE PON) ************************************************************* 10K (MIC LEVEL)
65
POWER
Ref. No.
POWER KEY
Description
TC
Remark Ref. No. C305 C306 C307 Part No. Description 470PF 0.01uF 0.001uF 10% 10% 10% Remark 50V 25V 50V
Part No.
A-1243-633-A POWER BOARD, COMPLETE (US, CND, MX, E92) A-1244-369-A POWER BOARD, COMPLETE (SP, E41, AUS) ********************** 1-533-233-31 FUSE HOLDER
1-162-962-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP 1-162-964-11 CERAMIC CHIP < CONNECTOR >
CN303 < CAPACITOR >
1-568-830-11 CONNECTOR, FFC 11P < IC >
C901 C902 C903 C904 C909 C927 C928
1-163-037-11 1-163-037-11 1-163-037-11 1-163-037-11 1-126-943-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
0.022uF 0.022uF 0.022uF 0.022uF 2200uF 1uF 1uF
10% 10% 10% 10% 20% 10%
50V 50V 50V 50V 25V 25V 50V
IC301
6-710-092-01 IC TA2068NG (5, HZ) < JUMPER RESISTOR >
1-100-591-91 CERAMIC CHIP 1-100-162-91 CERAMIC CHIP < DIODE >
JC301 JC302 JC303 JC304 JC305 JC306 JC307 JC308
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0 0 0 0
D901 6-501-569-01 DIODE 1N5401-C352 D902 6-501-569-01 DIODE 1N5401-C352 D903 6-501-569-01 DIODE 1N5401-C352 D904 6-501-569-01 DIODE 1N5401-C352 ************************************************************* A-1244-294-A POWER KEY BOARD, COMPLETE ************************** 3-831-441-11 CUSHION (B) < RESISTOR > R399 R400 R408 R455 1-216-817-11 1-216-813-11 1-216-821-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP < SWITCH > S403 1-786-050-21 SWITCH, KEY BOARD (DSPL/ENT) S408 1-786-050-21 SWITCH, KEY BOARD (POWER) S410 1-786-050-21 SWITCH, KEY BOARD (SLEEP) ************************************************************* A-1246-280-A TC BOARD, COMPLETE ****************** < CAPACITOR > C101 C102 C103 C104 C105 C107 C201 C202 C203 C204 C205 C207 C301 C302 C303 C304 1-162-964-11 1-104-658-91 1-165-176-11 1-162-966-11 1-162-923-11 1-162-962-11 1-162-964-11 1-104-658-91 1-165-176-11 1-162-966-11 1-162-923-11 1-162-962-11 1-104-658-91 1-104-658-91 1-104-658-91 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT 0.001uF 100uF 0.047uF 0.0022uF 47PF 470PF 0.001uF 100uF 0.047uF 0.0022uF 47PF 470PF 100uF 100uF 100uF 47uF 10% 20% 10% 10% 5% 10% 10% 20% 10% 10% 5% 10% 20% 20% 20% 20% 50V 10V 16V 50V 50V 50V 50V 10V 16V 50V 50V 50V 10V 10V 10V 35V 470 220 1K 100 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W
1-216-295-91 SHORT CHIP 1-216-864-11 SHORT CHIP 1-216-295-91 SHORT CHIP < TRANSISTOR >
Q301
8-729-901-81 TRANSISTOR < RESISTOR >
2SC2412K-T-146-R
R101 R102 R103 R104 R105 R106 R110 R111 R112 R201 R202 R203 R204 R205 R206 R210 R211 R212 R301 R302 R303 R304 R305 R306 R307 R308 R309 R314 R315
1-216-835-11 1-216-807-11 1-216-843-11 1-216-835-11 1-216-835-11 1-216-825-11 1-216-809-11 1-216-829-11 1-216-827-11 1-216-835-11 1-216-807-11 1-216-843-11 1-216-835-11 1-216-835-11 1-216-825-11 1-216-025-11 1-216-829-11 1-216-827-11 1-216-857-11 1-216-829-11 1-216-829-11 1-216-821-11 1-216-817-11 1-218-867-11 1-216-797-11 1-216-837-11 1-216-805-11 1-216-817-11 1-216-817-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP < SWITCH >
15K 68 68K 15K 15K 2.2K 100 4.7K 3.3K 15K 68 68K 15K 15K 2.2K 100 4.7K 3.3K 1M 4.7K 4.7K 1K 470 6.8K 10 22K 47 470 470
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
S301 1-126-947-11 ELECT
1-786-126-11 SWITCH, SLIDE (REC/PB)
66
TC
Ref. No. Part No. Description < TRANSFORMER > T301 1-416-041-11 TRANSFORMER, BIAS OSCILLATION ************************************************************* A-1244-418-A TUNER BOARD, COMPLETE (US, CND, MX, E92) A-1244-419-A TUNER BOARD, COMPLETE (SP, E41, AUS) ********************** 2-895-061-01 TERMINAL, ANTENNA < CAPACITOR > C1 C4 C7 C8 C9 C10 C11 C12 C13 C14 1-162-923-11 1-162-964-11 1-162-910-11 1-162-964-11 1-162-915-11 1-126-960-11 1-107-826-11 1-126-963-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP 47PF 0.001uF 5PF 0.001uF 10PF 1uF 0.1uF 4.7uF 0.01uF 0.01uF 5% 10% 0.25PF 10% 0.5PF 50V 50V 50V 50V 50V Remark Ref. No. C59 C60 C61 C62 C63 C65 C66 C68 C77 C78 C80 C95 Part No. Description 100PF 0.001uF 100PF 100PF 100PF 4.7uF 100PF 100PF 5% 10% 5% 5% 5% 20% 5% 5%
TUNER
Remark 50V 50V 50V 50V 50V 50V 50V 50V
1-162-927-11 CERAMIC CHIP 1-162-964-11 CERAMIC CHIP 1-162-927-11 CERAMIC CHIP 1-162-927-11 1-162-927-11 1-126-963-11 1-162-927-11 1-162-927-11 CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP
1-162-968-11 CERAMIC CHIP 1-162-968-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP 1-162-964-11 CERAMIC CHIP < FILTER >
0.0047uF 10% 50V (SP, E41, AUS) 0.0047uF 10% 50V (SP, E41, AUS) 0.01uF 10% 25V 0.001uF 10% 50V
1-162-970-11 CERAMIC CHIP
20% 50V 10% 16V 20% 50V 10% 25V (US, CND, MX, E92) 10% 25V (SP, E41, AUS)
CF2 CF4
1-760-235-81 FILTER, CERAMIC 1-781-962-21 FILTER, CERAMIC < CONNECTOR >
CNP1
1-568-854-11 CONNECTOR, FFC 11P < TRIMMER >
C14 C15 C15 C18 C20 C21 C22 C23 C24 C26 C27 C29 C30 C31 C32 C33 C34 C35 C37 C39 C41 C42 C43 C47 C49 C51 C52 C53 C54 C55 C56 C57
1-164-227-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP 1-164-227-11 CERAMIC CHIP 1-126-923-91 ELECT 1-107-826-11 CERAMIC CHIP 1-126-960-11 1-107-826-11 1-126-960-11 1-162-960-11 1-162-927-11 1-162-927-11 1-104-658-91 1-162-970-11 1-162-919-11 1-162-964-11 1-162-970-11 1-162-970-11 1-162-970-11 1-162-970-11 1-107-826-11 1-164-230-11 1-162-927-11 1-162-919-11 1-162-915-11 1-161-051-00 1-162-919-11 1-162-915-11 1-137-190-91 1-126-923-91 1-162-927-11 ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CERAMIC CHIP CERAMIC CHIP FILM ELECT CERAMIC CHIP
0.022uF
10% 25V (US, CND, MX, E92) 0.01uF 10% 25V (SP, E41, AUS) 0.022uF 10% 25V (US, CND, MX, E92) 220uF 20% 10V 0.1uF 10% 16V 1uF 0.1uF 1uF 220PF 100PF 100PF 100uF 0.01uF 22PF 0.001uF 0.01uF 0.01uF 0.01uF 0.01uF 0.1uF 220PF 100PF 22PF 10PF 0.01uF 22PF 10PF 0.22uF 220uF 100PF 0.001uF 0.001uF 20% 10% 20% 10% 5% 5% 20% 10% 5% 10% 10% 10% 10% 10% 10% 5% 5% 5% 0.5PF 10% 5% 0.5PF 5% 20% 5% 10% 10% 50V 16V 50V 50V 50V 50V 10V 25V 50V 50V 25V 25V 25V 25V 16V 50V 50V 50V 50V 25V 50V 50V 50V 10V 50V 50V 50V
CT1 CT3
1-141-442-91 CAP, CERAMIC TRIMMER 1-141-304-21 CAP, CERAMIC TRIMMER < DIODE >
20PF 10PF
D1 D2 D3 D10 D11
8-719-078-48 8-719-078-48 8-719-050-69 8-719-988-61 8-719-988-61
DIODE DIODE DIODE DIODE DIODE < IC >
KV1471ETR-G KV1471ETR-G KV1520N 1SS355TE-17 1SS355TE-17
IC1 IC2
6-700-512-01 IC TA2149BN 8-759-483-40 IC LC72137M-TLM-E < JUMPER RESISTOR >
JC1 JC2 JC3 JC4 JC5 JC6 JC11 JC12 JC13 JC24 JC33 JC34
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0 0 0 0 0 0 (SP, E41, AUS) 0 0
1-216-864-11 SHORT CHIP 1-216-864-11 SHORT CHIP < COIL >
1-162-964-11 CERAMIC CHIP 1-162-964-11 CERAMIC CHIP
L1 L2 L3 L4 L11
1-409-775-11 1-416-509-11 1-754-117-12 1-411-234-21 1-414-142-11
COIL, AIR-CORE COIL, AIR-CORE ANTENNA, FERRITE-ROD (MW) COIL, AM OSC INDUCTOR 1uH (US, CND, MX, E92)
67
TUNER
Ref. No. L21
VOLUME KEY
Part No. Description
WOOFER KEY
Remark 10uH Ref. No. R458 Part No. Description 100 5% Remark 1/10W
1-410-509-11 INDUCTOR < RESISTOR >
1-216-809-11 METAL CHIP < SWITCH >
R1 R2 R3 R4 R5 R10 R11 R13 R14 R24 R30 R31 R32 R33 R40 R41 R50 R51 R52 R53 R54 R55 R56 R57 R58 R59 R60 R61 R63 R65 R91 R92 R94
1-216-817-11 1-216-817-11 1-216-833-11 1-216-833-11 1-216-821-11 1-216-805-11 1-216-825-11 1-216-821-11 1-216-821-11 1-216-813-11 1-216-837-11 1-216-829-11 1-216-845-11 1-216-833-11 1-216-849-11 1-216-833-11 1-216-821-11 1-216-833-11 1-216-864-11 1-216-829-11 1-216-817-11 1-216-833-11 1-216-813-11 1-216-809-11 1-216-825-11 1-216-825-11 1-216-825-11 1-216-825-11 1-216-833-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
470 470 10K 10K 1K 47 2.2K 1K 1K 220 22K 4.7K 100K 10K 220K 10K 1K 10K 0 4.7K 470 10K 220 100 2.2K 2.2K 2.2K 2.2K 10K 10K 220 220 1K
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
S404 S407 S411 S412 S418
1-786-050-21 SWITCH, KEY BOARD (MODE) 1-786-050-21 SWITCH, KEY BOARD (VOL+) 1-786-050-21 SWITCH, KEY BOARD (AUTO PRESET RADIO/BAND) 1-786-050-21 SWITCH, KEY BOARD (AUDIO IN) 1-786-050-21 SWITCH, KEY BOARD (REPEAT)
S420 1-786-050-21 SWITCH, KEY BOARD (VOL) ************************************************************* A-1244-298-A WOOFER KEY BOARD, COMPLETE *************************** 3-831-441-11 CUSHION (B) < CONNECTOR > CNP401 1-815-443-11 PIN, CONNECTOR (PWB) 2P < RESISTOR > R401 R402 R403 R416 R417 R423 R424 R459 1-216-813-11 1-216-817-11 1-216-821-11 1-216-825-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 220 470 1K 2.2K 1K 1K 2.2K 100 5% 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
1-216-821-11 METAL CHIP 1-216-825-11 METAL CHIP 1-216-809-11 METAL CHIP < SWITCH >
S409 S415 S416 S417 S419
1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21 1-786-050-21
SWITCH, KEY BOARD (ROCK) SWITCH, KEY BOARD (DANCE) SWITCH, KEY BOARD (SALSA) SWITCH, KEY BOARD (FLAT) SWITCH, KEY BOARD (POWER DRIVE WOOFER)
< TRANSFORMER > T1 T2 1-433-741-11 TRANSFORMER, IF 1-419-465-11 COIL (DET) < VIBRATOR > X1 1-795-449-11 VIBRATOR, CRYSTAL (75kHz) ************************************************************* A-1244-293-A VOLUME KEY BOARD, COMPLETE *************************** 3-831-441-11 CUSHION (B) < RESISTOR > R411 R412 R413 R414 R415 R425 R443 1-216-813-11 1-216-817-11 1-216-821-11 1-216-821-11 1-216-825-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 220 470 1K 1K 2.2K 2.2K 1K 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
S421 1-786-050-21 SWITCH, KEY BOARD (REGGAETON) ************************************************************* MISCELLANEOUS ************** 0 160 164 166 205 206 253 CNP2 D403 D404 D405 D407 D408 D409 D410 D411 0 F902 8-820-126-02 1-832-404-21 1-832-613-21 1-754-376-11 1-452-899-11 1-797-375-11 1-833-922-11 6-501-452-01 6-501-452-01 6-501-452-01 6-501-452-01 6-501-452-01 6-501-452-01 6-501-452-01 6-501-452-01 OPTICAL PICK-UP (KSM-213CDP/C2NP) CABLE, FLEXIBLE FLAT (16 CORE) CABLE, FLEXIBLE FLAT (21 CORE) ANTENNA, TELESCOPIC MAGNET DECK, MECHANICAL (H21SB-C05) CORD, CONNECTION (WITH PLUG) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION) DIODE 1L4345V22DOTDT02 (ILLUMINATION)
1-532-504-33 FUSE (T4AL/250V)
68
Ref. No. 0 J901 0 J901 S201 SP191 SP291 SP393 SW2
Part No. 1-526-838-11 1-540-009-11 1-771-853-11 1-826-684-11
Description
Remark
INLET, AC 2P (- AC IN) (SP, E41, AUS) INLET, AC (- AC IN) (US, CND, MX, E92) SWITCH, DETECTION (LIMIT) SPEAKER (10cm)
1-826-684-11 SPEAKER (10cm) 1-826-683-11 SPEAKER (13cm) 1-692-960-11 SWITCH, PUSH (1 KEY)
(Z PUSH OPEN/CLOSE) 0 T901 1-435-964-12 TRANSFORMER, POWER (US, CND, MX, E92) 0 T901 1-435-965-12 TRANSFORMER, POWER (SP, E41, AUS) ************************************************************* ACCESSORIES *********** A-1246-031-A REMOTE COMMANDER (RMT-CG700A) (Including Battery Case) 1-769-412-22 CORD, POWER (G770CP) 1-782-126-11 CORD, POWER (US, CND, MX, E92) 1-827-945-12 CORD, POWER (AUS) 3-096-718-11 MANUAL, INSTRUCTION (ENGLISH) (G700CP) 3-096-718-21 MANUAL, INSTRUCTION (ENGLISH, SPANISH) (E92) 3-096-718-31 MANUAL, INSTRUCTION (ENGLISH, FRENCH) (SP) 3-096-718-41 MANUAL, INSTRUCTION (SPANISH) (E41) 3-096-718-51 MANUAL, INSTRUCTION (ENGLISH) (AUS) 3-096-718-61 MANUAL, INSTRUCTION (ENGLISH, FRENCH) (CND) 3-096-718-71 MANUAL, INSTRUCTION (SPANISH) (MX)
0 0 0
69
REVISION HISTORY
Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0 Date 2007.03 New Description of Revision

Sony CFD-G700CP-G770CP-G-770CPK

Uploaded by

Copyright:

Available Formats

Sony CFD-G700CP-G770CP-G-770CPK

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sony CFD-G700CP-G770CP-G-770CPK

Uploaded by

Copyright:

Available Formats

What are the main components of the device?

What are the main components of the device?

How does the device function?

How does the device function?

CFD-G700CP/G770CP/ G770CPK

CFD-G505/G555CP/G555CPK KSM-213CDP/C2NP KSS-213C HCD-EC50 H21SB-C05

: AC 120V area in E model : Mexican model : Singapore model

SERVICING NOTES ............................................... 4 GENERAL ................................................................... 5 DISASSEMBLY

ELECTRICAL ADJUSTMENTS .......................... 23 DIAGRAMS

TEST MODE ............................................................... 21 MECHANICAL ADJUSTMENTS ......................... 23

ELECTRICAL PARTS LIST .................................. 57

CFD-G700CP/G770CP/G770CPK SECTION 1 SERVICING NOTES

Fig. A. Using an AC voltmeter to check AC leakage.

CFD-G700CP/G770CP/G770CPK SECTION 2 GENERAL

Playing a CD/MP3 disc

2 Select the program source you want to record.

on the unit to start recording ( depressed automatically).

Listening to the radio

1 Press RADIO/BAND AUTO PRESET

Press on the unit ( on the remote) . To resume play, press it again.

Before using the unit

To adjust the volume

To listen through headphones

To select the sound characteristic

To reinforce the bass sound

on the unit. The unit starts playing.

Stop playback Fast-forward or rewind* Eject the cassette

Example of folder structure and playing order

* When the tape is wound to the end, press .

Playing tracks/MP3 files in random order (Shuffle Play)

Presetting radio stations

Connecting optional component

Checking the information of an audio CD

1 Press RADIO/BAND AUTO PRESET

. CD appears in the display.

2 Hold down RADIO/BAND AUTO PRESET 3 Press DSPL/ENT

Total track number Total playing time

If a station cannot be preset automatically

1 Press RADIO/BAND AUTO PRESET

Checking the information of an MP3 disc

To cancel Shuffle Play

4 Press PRESET + or 5 Press DSPL/ENT

on the unit. The new station replaces the old one.

Total folder number Total file number

Creating your own program (Program

until the band you want

To check file information

. CD appears in the display. until PGM flashes in the display.

2 Press MODE 3 Press or

4 Press PRESET + or 5 Press ENTER

1 Connect the built-in audio cable with stereo-mini

Playing preset radio stations

Playing tracks/MP3 files repeatedly

Programed track number

Playing order MP3 disc (Program Play) Programed file number

on the unit to tune in the

. CD appears in the display.

1 Press RADIO/BAND 2 Press PRESET + or

. to tune in the stored station.