Service Manual: MVC-FD85/FD90

MVC-FD85/FD90
SERVICE MANUAL US Model

Canadian Model
AEP Model
Level 2 UK Model
E Model
Australian Model
Hong Kong Model
Ver 1.0 2000. 03 Chinese Model
Tourist Model
Japanese Model
MVC-FD85/FD90
Korea Model
MVC-FD90
Photo: MVC-FD90
Brazilian Model
MVC-FD85
On the FC-72 board This service manual contains information

This service manual provides the information that is premised the circuit board for japanese model as well.
replacement service and not intended repair inside the FC-72 board.
Therefore, schematic diagram, printed wiring board and electrical parts list of
the FC-72 board are not shown.
The following pages are not shown.
Block diagram ............................... Page 3-9 to 3-18
Schematic diagram ....................... Page 4-9 to 4-26
Printed wiring board ..................... Page 4-27 to 4-30
Electrical parts list ........................ Page 6-7 to 6-14
The above-described information is shown in service manual Level 3.
SPECIFICATIONS
DIGITAL STILL CAMERA

Table for differences of function
Model MVC-FD85 MVC-FD90 Remark
Destination US, CND, AEP, UK, E, US, CND, AEP, UK, E,
AUS, HK, CN, JE, BR, J AUS, HK, CN, JE, KR, J
CCD imager size 1/2.7 inch 1/3.6 inch
Lens Optical 3× 8×
Manual foucs a a: with CN401 of FC-72 board. Abbreviation
CND: Canadian mode
LANC jack a a: with J782 of PK-50 board. HK: Hong Kong model
CD board CD-248 CD-246 AUS: Austrarian model
FC board FC-72 FC-72 KR: Korea model
PD board PD-52 PD-50 BR: Brazilian model
CN: Chinese model
FU board FU-146 FU-140 JE: Tourist model
J: Japanese model
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered 4. Look for parts which, through functioning, show obvious signs
connections. Check the entire board surface for solder splashes of deterioration. Point them out to the customer and
and bridges. recommend their replacement.
2. Check the interboard wiring to ensure that no wires are 5. Check the B+ voltage to see it is at the values specified.
"pinched" or contact high-wattage resistors. 6. Flexible Circuit Board Repairing
3. Look for unauthorized replacement parts, particularly • Keep the temperature of the soldering iron around 270˚C
transistors, that were installed during a previous repair. Point during repairing.
them out to the customer and recommend their replacement. • Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
—2—
TABLE OF CONTENTS
SERVICE NOTE ····································································· 5 • CD-248 (CCD IMAGER)(FD85 MODEL)
SCHEMATIC DIAGRAM ······························ 4-8
1. GENERAL • PK-50 (AV OUT/KEY IN, BACK LIGHT, RGB, TG)
Getting started (FD90 MODEL)
Identifying the parts ······························································· 1-1 PRINTED WIRING BOARD ······················· 4-31
Preparing the power supply ··················································· 1-2 • PK-52 (AV OUT/KEY IN, BACK LIGHT, RGB, TG)
Starting the date and time ······················································ 1-3 (FD85 MODEL)
Inserting a floppy disk ··························································· 1-3 PRINTED WIRING BOARD ······················· 4-35
Basic operations • PK-50/52 (AV OUT/KEY IN)(1/4)(1/3)
Recording still images ··························································· 1-3 SCHEMATIC DIAGRAM ···························· 4-39
Recording moving images ····················································· 1-4 • PK-50/52 (BACK LIGHT)(2/4)(2/3)
Playing back still images ······················································· 1-5 SCHEMATIC DIAGRAM ···························· 4-41
Playing back moing images ··················································· 1-5 • PK-52 (RGB DRIVER/TG)(3/3)
Viewing images using a personal computer ·························· 1-5 SCHEMATIC DIAGRAM ···························· 4-43
Image file storage destinations and image file names ··········· 1-6 • PK-50 (RGB DRIVER)(3/4)
Advanced operations SCHEMATIC DIAGRAM ···························· 4-45
Before performing advanced operations ································ 1-6 • PK-50 (TG)(4/4)
Additional information SCHEMATIC DIAGRAM ···························· 4-47
Precautions ··········································································· 1-13 • FU-140/146 (DC IN)
Using your camera abroad ··················································· 1-13 SCHEMATIC DIAGRAM ···························· 4-49
Troubleshooting ··································································· 1-13 • FU-140 (DC IN)(FD90 MODEL)
Warning and notice messages ·············································· 1-14 PRINTED WIRING BOARD ······················· 4-51
Self-diagnosis display ·························································· 1-14 • FU-146 (DC IN)(FD85 MODEL)
LCD screen indicators ························································· 1-15 PRINTED WIRING BOARD ······················· 4-53
4-3. WAVEFORM ································································· 4-55
2. DISASSEMBLY 4-4. PARTS LOCATION ······················································ 4-59
2-1. CABINET (REAR) BLOCK ASSEMBLY ····················· 2-1
2-2. FC-72 BOARD, FLOPPY DISK DRIVE ······················· 2-2 5. ADJUSTMENTS
2-3. LENS BLOCK ASSEMBLY ··········································· 2-3 1. Before Starting Adjustment ············································· 5-1
2-4. LCD, PK-50/52 BOARD ················································· 2-4 1-1. Adjusting Items When Replacing
2-5. FLASH UNIT, FU-140/146 BOARD ······························ 2-5 Main Parts and Boards ···················································· 5-2
2-6. DC-IN CONNECTOR, MICROPHONE UNIT ·············· 2-6 5-1. ADJUSTMENT ······························································· 5-3
2-7. HINGE ASSEMBLY, 1-1. PREPARATIONS BEFORE ADJUSTMENT ················· 5-3
BATTERY TERMINAL BOARD ··································· 2-6 1-1-1. List of Service Tools ························································ 5-3
2-8. EJECT BUTTON SECTION ·········································· 2-7 1-1-2. Preparations ····································································· 5-4
2-9. FOCUS STEPPING MOTOR, 1-1-3. Discharging of the Flashlight Power Supply ··················· 5-5
ZOOM STEPPING MOTOR, 1-1-5. Precaution ········································································ 5-7
ND-METER (MVC-FD90) ············································· 2-7 1. Setting the Switch ···························································· 5-7
2-10. FOCUS MOTOR UNIT, 2. Order of Adjustments ······················································ 5-7
ZOOM MOTOR UNIT (MVC-FD85) ···························· 2-7 3. Subjects ··········································································· 5-7
2-11. CIRCUIT BOARDS LOCATION ··································· 2-8 1-2. INITIALIZATION OF B, D, E, F, 7 PAGE DATA ········· 5-8
2-12. FLEXIBLE BAORDS LOCATION ································ 2-8 1-2-1. INITIALIZATION OF D PAGE DATA ·························· 5-8
1. Initializing the D Page Data ············································ 5-8
3. BLOCK DIAGRAMS 2. Modification of D Page Data ··········································· 5-8
3-1. OVERALL BLOCK DIAGRAM (1/2) ··························· 3-1 3. D Page Table ···································································· 5-8
3-2. OVERALL BLOCK DIAGRAM (2/2) ··························· 3-3 1-2-2. Initializing the B, E, F, 7 Page Data ································ 5-9
3-3. POWER BLOCK DIAGRAM (1/2) ································ 3-5 1. Initializing the B, E, F, 7 Page Data ································ 5-9
3-4. POWER BLOCK DIAGRAM (2/2) ································ 3-7 2. Modification of B, E, F, 7 Page Data ······························· 5-9
3. F Page table ··································································· 5-10
Founctional block diagrams are not shown. 4. 7 Page Table ··································································· 5-11
Pages from 3-9 to 3-18 are not shown. 5. E Page Table ·································································· 5-12
6. B Page Table ·································································· 5-12
4. PRINTED WIRING BOARDS AND 1-3. VIDEO SYSTEM ADJUSTMENTS ····························· 5-13
1. Video Output Level Adjustment (FC-72 board) ············ 5-13
SCHEMATIC DIAGRAMS
1-4. CAMERA SYSTEM ADJUSTMENTS ························ 5-14
4-1. FRAME SCHEMATIC DIAGRAM ································ 4-1
1. Zoom Key Center Adjustment ······································· 5-14
4-2. PRINTED WIRING BOARDS AND
2. HALL Adjustment ························································· 5-14
SCHEMATIC DIAGRAMS ············································ 4-4
3. Flange Back Adjustment (Using Minipattern Box) ······· 5-15
• CD-246 (CCD IMAGER)(FD90 MODEL)
4. Flange Back Adjustment
PRINTED WIRING BOARD ························· 4-5
(Using Flange Back Adjustment Chart) ························ 5-16
4-1. Flange Back Adjustment (1) ·········································· 5-16
SCHEMATIC DIAGRAM ······························ 4-6
4-2. Flange Back Adjustment (2) ·········································· 5-16
5. Flange Back Check ························································ 5-17
PRINTED WIRING BOARD ························· 4-7
6. F No. Standard Data Input ············································· 5-17
Schematic diagram and printed wiring board of the FC- 7. Mechanical Shutter Adjustment ···································· 5-17
72 board are not shown. 8. Picture Frame Setting ···················································· 5-18
Pages from 4-9 to 4-30 are not shown. 9. Light Level Adjustment and ND Shutter Check ············ 5-19
—3—
10. Mixed Color Cancel Adjustment ··································· 5-19 6. REPAIR PARTS LIST
11. Auto White Balance Standard Data Input ····················· 5-20 6-1. EXPLODED VIEWS ······················································ 6-1
12. White Balance ND Filter Compensation 6-1-1. CABINET (FRONT) BLOCK SECTION-1 ··················· 6-1
(MVC-FD90) ································································· 5-20 6-1-2. CABINET (FRONT) BLOCK SECTION-2 ··················· 6-2
13. Auto White Balance Adjustment ··································· 5-21 6-1-3. CABINET (REAR) BLOCK SECTION ························· 6-3
14. Color Reproduction Adjustment (ND Filter OFF) ········ 5-21 6-1-4. LENS BLOCK SECTION ··············································· 6-4
15. Color Reproduction Adjustment (ND Filter ON) 6-2. ELECTRICAL PARTS LIST ·········································· 6-5
(MVC-FD90) ································································· 5-22
16. Gr and Gb Level Compensation ···································· 5-22 Electrical parts list of the FC-72 board is not shown.
17. Color Reproduction Check ············································ 5-23 pages 6-7 to 6-14 are not shown.
18. White Balance Check ···················································· 5-24
18-1. Data Check ···································································· 5-24
* Parts reference sheet and color reproduction frame is shown on
18-2. Luminance Point Check ················································ 5-24
page 137.
19. Strobe White Balance Adjustment ································· 5-25
20. Strobe Light Level and White Balance Check ·············· 5-25
21. CCD Black Defect Compensation ································· 5-26
22. CCD White Defect Compensation ································ 5-26
1-5. LCD SYSTEM ADJUSTMENT ··································· 5-27
1-5-1. LCD Type Check ··························································· 5-27
1-5-2. LCD SYSTEM ADJUSTMENT (PK-50 board)
(MVC-FD90) ································································· 5-28
1. LCD Initial Data Input ·················································· 5-28
2. VCO Adjustment (PK-50 board) ··································· 5-28
3. D Range Adjustment (PK-50 board) ····························· 5-29
4. Bright Adjustment (PK-50 board) ································· 5-29
5. Contrast Adjustment (PK-50 board) ······························ 5-30
6. Color Adjustment (PK-50 board) ·································· 5-30
7. V-COM Level Adjustment (PK-50 board) ···················· 5-31
8. V-COM Adjustment (PK-50 board) ······························ 5-31
9. White Balance Adjustment (PK-50 board) ···················· 5-32
(MVC-FD85) ································································· 5-32
1. LCD Initial Data Input ·················································· 5-32
2. VCO Adjustment (PK-52 board) ··································· 5-33
3. Black Limit Adjustment (PK-52 board) ························ 5-33
4. Bright Adjustment (PK-52 board) ································· 5-34
5. Contrast Adjustment (PK-52 board) ······························ 5-34
6. Color Adjustment (PK-52 board) ·································· 5-35
7. VG Center Adjustment (PK-52 board) ·························· 5-35
8. V-COM Adjustment (PK-52 board) ······························ 5-36
9. White Balance Adjustment (PK-52 board) ···················· 5-36
1-6. SYSTEM CONTROL SYSTEM ADJUSTMENT ········ 5-37
1. Battery End Adjustment (FC-72 board) ························ 5-37
2. Alignment Check (FDD UNIT) ···································· 5-38
5-2. SERVICE MODE ·························································· 5-39
2-1. ADJUSTMENT REMOTE COMMANDER ················ 5-39
1. Using the Adjustment Remote Commander ·················· 5-39
2. Precautions Upon Using
the Adjustment Remote Commander ···························· 5-39
2-2. DATA PROCESS ··························································· 5-40
2-3. SERVICE MODE ·························································· 5-41
1. Setting the Test Mode ···················································· 5-41
2. Bit Value Discrimination ··············································· 5-41
3. Emergency Memory Address of Flash Unit ·················· 5-41
4. Record of Use check ······················································ 5-42
5. Self Diagnostics Log Check ·········································· 5-42
6. Switch Check (1) ··························································· 5-43
7. Switch Check (2) ··························································· 5-43
8. LED Check ···································································· 5-43
—4—
SERVICE NOTE
• NOT FOR REPAIR

Make sure that the flat cable and flexible board are not cracked of When remove a connector, don't pull at wire of connector.
bent at the terminal. Be in danger of the snapping of a wire.
Do not insert the cable insufficiently nor crookedly.
When installing a connector, don't press down at wire of connector.

Be in danger of the snapping of a wire.
Cut and remove the part of gilt

which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
[Discharging of the FLASH unit’s charging capacitor]
The charging capacitor of the FLASH unit is charged up to the

maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the MVC-FD85/FD90 is simply turned off. Therefore,
the remaining voltage must be discharged as described below.
Preparing the Short Jig Discharging the Capacitor

To preparing the short jig. a small clip is attached to each end of a Short circuits between the positive and the negative terminals of
resistor of 1 kΩ /1 W (1-215-869-11) charged capacitor with the short jig about 10 seconds.
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
1 kΩ/1 W
Short jig
Wrap insulating tape.
Capacitor
—5—
[Description on Self-diagnosis Display]
Self-diagnosis display
• C: ss: ss
The contents which can be handled
by customer, are displayed.
• E: ss: ss
The contents which can be handled
by engineer, are displayed.
Display Code Countermeasure Cause Caution Display During Error

Change the disk and turn off the main
C:32:01 Defective floppy disk. DRIVE ERROR
power then back on.
• The type of floppy disk that cannot be
Replace the floppy disk. used by this machine, is inserted.
C:13:01 Format the floppy disk with the MVC- (Such as 2DD) DISK ERROR
FD85/FD90. • Data is damaged.
• Unformatted disk is inserted.
*2 Flash LED
Checking of flash unit or replacement of
E:91:01 Abnormality when flash is being Flash display
flash unit
charged. Flashing at 3.2 Hz
*1
E:61:00
Checking of lens drive circuit When failed in the focus initialization. —
*1
E:61:10
Note: The error code is cleared if rthe battery is removed, except

defective flash, unit.
*1 : The error display is given in two ways.
*2 : When the flash charging failed, Page:D, Address:C7, Data:04
are written.
After repair, be sure to write Page:D, Address:C7, Data:00.
—6—
MVC-FD85/FD90
SECTION 1
This section is extracted from
GENERAL instruction manual.
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15E
MVC-FD85/FD90
SECTION 2
DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1 . Cabinet (Rear) block assembly
LCD, PK-50/52 board

2-4. LCD, PK-50/52 board
chack service position
MVC-FD85/FD90
2-8. Eject button section
2-2. FC-72 board, Floppy disk drive
2-6. DC-IN connector, Microphone UNIT

Control switch block (MF 330)(MVC-FD90)
2-7. Hinge assembly, Battery terminal board

Control switch block
2-3. Lens block assembly

Removing the CD-246/248 boards
Main (FC-72) board, Lens block assembly

2-9. Focus stepping motor, Zoom stepping motor,

ND meter (MVC-FD90)
2-10. Focus motor unit, Zoom motor unit

(MVC-FD85)
OVERALL
2-5. Flash unit, FU-146 board
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. CABINET (REAR) BLOCK ASSEMBLY
7 Cabinet (front) block assembly
5 Two screws (M2 × 4),

lock ace, p2
3 Two screws (M2 × 4), lock ace, p2
2
-7
FCard
B o
6 Cabinet (rear) block assembly

4 Screw (M2 × 4),
lock ace, p2
2 Screw (M2 × 4),

lock ace, p2
1 Two screws (M2 × 4),
lock ace, p2
2-1
2-2. FC-72 BOARD, FLOPPY DISK DRIVE
9 FU-51 harness (12p)
8 FU-52 harness (9p)
1 Microphone unit (2p)
q; Flash unit (10p)

qa Cabinet (front)
block assembly qf Blind sheet
qg Floppy disk drive (4 × )

2 Flexible board (18P)
MVC-FD85 FP-231
MVC-FD90 FP-167 6 Claw
qd FC Bracket
3 Lens block assembly
MVC-FD85 (26P) qs Three screws
MVC-FD90 (24P) (M2 × 2.5)
7 FC-72 board
2
-7
FCard
B o
4 Control switch block (MF330)(6p)
(MVC-FD90)
5 Four screws (M2 × 2.5)

MVC-FD90
FC-72
board
Lens block
assembly (26P)
Cautions When Handling FDD
1. Correct Way of Holding an FDD 2. Prohibited Items
Do not apply any physical stress to the center of the top plate.
Do not apply any physical

stress to the spindle motor.
Wear an earthed wrist strap. Do not hold an FDD by sandwiching

Range of holding FDD
the upper and lower surfaces.
If the FDD is not held correctly,

the components of the FDD may be bent.
2-2
2-3. LENS BLOCK ASSEMBLY
3 Cabinet (front) assembly
1 Tapping screw (M2 × 5)
2 Lens block assembly

(MVC-FD90) 2 Lens block assembly
(MVC-FD85)
REMOVING THE CD-246 BOARD REMOVING THE CD-248 BOARD

2 Two stapping crews (M1.7 × 6) 2 Two tapping screws (M1.7 × 6)
6 Shield rubber (FM) 6 Seal rubber (CL)
5 Optical filter block 5 Optical filter block
4 CCD fitting 4 CCD fitting
adaptor(FH) adaptor (CL)
8 CD-248 board
8 CD-246 3 Four
board claws
3 Four claws
7 CCD block assembly (CCD imager) 7 CCD block assembly (CCD imager)
(Remove soldering) (Remove soldering)
1 FP-167 flexible board 1 FP-231 flexible board
[ MAIN (FC-72) BOARD, LENS BLOCK (CD-246/248 BOARD) CHECK SERVICE POSITION ]
FU-52 harness (9p)

CPC-12 jig
FU-51 harness (12p) (J-6082-436-A)
AC IN
AC POWER FC-72 board
ADAPTOR
2
PK-52 board (MVC-FD85)
-7 rd PK-50 board (MVC-FD90)
FC oa
B
CD-248 board 2
-5 rd
PK oa
Lens block assembly B
(MVC-FD85)
CD-246 board
MVC-FD90 FC-72
board
Lens block assembly

(MVC-FD90) Lens block
assembly (24P)
2-3
2-4. LCD, PK-50/52 BOARD
REMOVING THE SPEAKER
(PRECAUTION DURING INSTALLATION)
3 Speaker (2.0CM)
Align the switch position as shown.
Cabinet
(rear)
1 Two claws 2 Speaker retainer

LCD selection retainer
qd Cabinet (rear) assembly
qs Liquid cryst module indicator
qa Cold cathode fluorescent tube
2 Cold cathode fluorescent tube (20p)
q; Back light retainer

A
9 Four tapping
screws (M2 × 5)
3 Speaker
(2.0CM)(2p)
6 Eight tapping
A screws (M2 × 5)
1 Liquid cryst
module indicator (24p) -
PKard 5 PK shield case
B o (lower) assembly
8 Tapping screw (M2 × 5)
4 Tapping
screw (M2 × 5)
7 PK-52 board (MVC-FD85)
PRECAUTION DURING
INSTALLATION
Set this knob the center. Note : Refer to page 5-27 for LCD type check.
[ LCD, PK-50/52 BOARD CHECK SERVICE POSITION ]
FC-72 board
CD-246 board (MVC-FD90)

CD-248 board (MVC-FD85)
2
AC IN -7
AC POWER FCard
ADAPTOR B o
CPC-12 jig
(J-6082-436-A)
rd
o -
B K
a
P
Liquid cryst module indicator (24p)

Cold cathode fluorescent tube (20p)
2-4
2-5. FLASH UNIT, FU-140/146 BOARD
2 Two tapping
screws (M2 × 5)
1 ST inslating sheet
6 FU-140 board (MVC-FD90)

FU-146 board (MVC-FD85)
5 Two tapping
screws (M2 × 5)
4 Control switch block (6p)

3 Flash unit
Short jig (see page 5)

1kΩ. 1W
parts.No.1-215-869-11
When handling the flash unit, be sure to
discharge the charging capacitor before
handling it.
For discharge short jig to the positive (+)
and negetive (–) terminals of the charging
capacitor for about ten seconds.
[ OVERALL CHECK SERVICE POSITION ]
AC IN
AC POWER
ADAPTOR FU-140 board (MVC-FD90)
FU-146 board (MVC-FD85)
CPC-12 jig
(J-6082-436-A)
FC-72 board
CD-246 2
-7 rd
board FC oa
B PK-50 board (MVC-FD90)
Liquid cryst module
indicator (24p)
- rd
Lens block assembly PK oa
B
(MVC-FD90)
CD-248 board Cold cathode

fluorescent tube (20p)
Lens block assembly
(MVC-FD85) MVC-FD90
FC-72
board
Lens block
assembly (24P)
2-5
2-6. DC-IN CONNECTOR, MICROPHONE UNIT

Align the switch position as shown.
Control switch block

(MF 330)
REMOVING THE Focus slider
MICROPHONE UNIT 2 DC retainer
2 Microphone cover 1 Two tapping
4 Microphone cushion screws (M2 × 5)
3 Microphone holder
3 DC-IN
6 Microphone unit connector
PRECAUTION DURING
INSTALLATION 1 Two tapping
screws (M2 × 5)
DC retainer
2 Control switch block (MF 330)
1 Two tapping (MVC-FD90)
screws (M2 × 5)
Cabinet (front)
assembly
5 Microphone sheet
2-7. HINGE ASSEMBLY, BATTERY TERMINAL BOARD
REMOVING THE CONTROL

8 SWITCH BLOCK (zoom and shutter)
2 Control switch
block
7 Two tapping
screws (M2 × 5)
4 Two claws
C 1 SW holder
6 Battery
terminal board (Remove it in the direction of the arrow C.)
5 Two claws
1 Hinge assembly
2 Two tapping
3 Battery holder
screws (M2 × 5)
REMOVING THE HINGE ASSEMBLY
2 Two tapping
screws (M2 × 4)
3 Hinge retainer
9 Remove the hinge assembly
in the direction of the arrow B.
B
1 8 Claw
A
7 Remove the hinge assembly
in the direction of the arrow A.
4 Battery lid 5 Tapping

6 Two claws screw (M2 × 5)
2-6
2-8. EJECT BUTTON SECTION
q; Lock button
9 Claw retainer
qd Eject knob
qa Lock button
5 Pinion gear
6 Parallel pin (DIA. 1.6 × 8)
qs Lock button
spring 4 Rack (B)
2 Gear cover

3 Eject spring
Knob 1 Three tapping
(Rack (B)) screws (M2 × 5)
Attach the Rack (A) and

Gear Cover so that the
Rack (B) knob agrees with
the Gear Cover Aposition
while the Rack (A) is A 8 Rack (A)
pushed toward its top (Gear cover) 7 Tapping screws
most position. Rack (A) Gear cover
2-9. FOCUS STEPPING MOTOR, 2-10.FOCUS MOTOR UNIT,

ZOOM STEPPING MOTOR, ZOOM MOTOR UNIT
ND-METER (MVC-FD85)
(MVC-FD90) 3 Lens sheet (L)
1 Two screws (M2 × 5)
1 Two screws (M2 × 5)
2 Lens frame
4 screw
2 Lens frame
5 Two screws
6 Remove soldering 7 Zoom stepping motor
9 Remove soldering
3 Lens sheet
8 screw
q; ND meter qs Remove soldering 5 Remove soldering 8 Remove soldering
6 Focus 9 Zoom
qd Focus stepping motor motor unit motor unit
7 Two screws
qa Two screws 4 Two screws
2-7
2-11.CIRCUIT BOARDS LOCATION
PK-50 (MVC-FD90) CD-246 (MVC-FD90)

PK-52 (MVC-FD85) FU-140 (MVC-FD90) CD-248 (MVC-FD85)
FU-146 (MVC-FD85)
FLASH UNIT
FC-72
2-12.FLEXIBLE BOARDS LOCATION
CONTROL SWITCH BLOCK (From FLOPPY DISK DRIVE)

(From ND901)
(From LCD901)
CONTROL SWITCH BLOCK (MF300) (From FLOPPY DISK DRIVE)

FP-165
(MVC-FD90)
FP-167(MVC-FD90) FP-231(MVC-FD85)
From LENS BLOCK, From LENS BLOCK,

MVC-FD90 MVC-FD85
2-8E
MVC-FD85/FD90
SECTION 3
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. Note:FD85 model:MVC-FD85
FD90 model:MVC-FD90
CD-248/246 BOARD FC-72 BOARD

Note:FD85 model/FD90 model
(4-13)
ZOOM
(4-8/4-6) (4-9)
LENS IRIS
ND FILTER (SHUTTRE)
IC201/101 CCD OUT IC102 12 AD DATA 12
IC301 16 DATA BUS
S/H,AGC, CAMERA DSP

CCD IMAGER A/D CONV. MEMORY CONTROL
VIDEO ENCODER 14
OPD,OSD,HOST IF ADDRESS BUS
FOCUS ZOOM (4-9) RES CONTROL
MOTOR MOTOR V1,V1B,V2, SG,JPEG,L-MODE
IRIS
ND FILTER METER V3A,V3B,V4,
MOTOR
M M M HALL
M RG,VSHT
H1,H2
IC101 AUDIO I/F
MCK12 MCK12 SHUTTER CONTROL

TIMING
FOCUS ZOOM H GENERATOR MCK24
RESET RESET MCK24 STROBO CONTROL
SENSOR SENSOR
(4-14)
MC XCS2
(4-11) IC184 IRIS CONT 1,2 ADDRESS MC XCS6
CAM SO,XCAM,SCK IC302 14

IC181 FOCUS
MOTOR
DRIVE
ZOOM
MOTOR
DRIVE
IC185 SDRAM DATA AU SDTO
64Mbit
ND FILTER IRIS DRIVE
16 AU SDTI
DRIVE
IC183 HALL (+)
HALL AMP
HALL AD
(4-19)
FD90 model
(4-11) XZM RST SENS (4-11/4-12)
XFC RST SENS
XZM RST SENS
XFC RST SENS
Y
C
IC901 VIDEO OUT
VIDEO AMP
(4-11)
IC182 MSHUT ON MSHUT ON Y
ENO,EN1
R-Y
SHUTTER DRIVE ENO A,B CONTENUDE ON
ENO,EN1 EN1 A,B B-Y
ENOA,B ND ON (SEE PAGE
ND ON EN1A,B STRB ON VD,HD 3-3)
(4-12)
EXT STRB ON
(SEE PAGE 4-19)
STRB ON
IC186
EVR
FLASH FLASH ST UNREG
UNIT UNIT STB CHARGE
CAM SO,XCAM SCK

FD90
model
(SEE PAGE 4-21)
FOCUS FOCUS A,B

LING
MF BLOCK
KEY AD0
FOCUS SW
(SEE PAGE 4-50)

ZOOM/ SHUTTER SW
XRS ON1,2
RELEASE ZOOM VR
ZOOM SW AD
UNIT
BT901
BATT
TERMINAL
Q001,004 BATT SIG
FAST CHARGE ON
BATT/XEXT
S SYS DD ON
LCD DD ON
(4-25)
FDD P5V
IC001 CAM 15V

CAM P5V
J902 FDD 4.9V
DC IN DC/DC
CONVERTER A 4.9V
CAM -7.5V
CAM 3.2V
D 3.2V
F002 A 3.2V
D 1.8V
PANEL -15.3V
PANEL 13.2V
PANEL 6.5V
PANEL 4.9V
F005
ACV UNREG
F006
BL UNREG
F001
ST UNREG
F004
BATT UNREG
FU-146/140
BOARD
Note:
FD85 model/FD90 model
16
3-1 3-2
MVC-FD85/FD90
3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
FC-72 BOARD FLOPPY Note:FD85 model:MVC-FD85

FD90 model:MVC-FD90
DISK DRIVE
UNIT
(4-18) (4-17)
WRITE DATA R/W A,B
DATA BUS 16 IC702 READ DATA IC704 ERASE

UPPER HEAD
SIDE 1
16 16 16 FD CONTROL
REC/PB AMP
WRITE GATE SPINDLE MOTOR DRIVE
3 STEPPING MOTOR DRIVE
ADDRESS BUS
SIDE 1 SELECT R/W A,B
DIRECTION
STEP LOWER HEAD
24 12 17
ERASE SIDE 2
TRK 00,INDEX
(4-15) WRITE PROTECT
IC501 IC506 IC505 FDD SELECT

FDD MOTOR ON DISK
SDRAM FLASH ROM FDD XDCHG

MC CAM 16Mbit 8Mbit FDD DENSITY
SH DSP SPINDLE
MC XCS2
(4-16) (4-16) MOTOR
DRIVE M SPINDLE
MOTOR
MC XCS6 MC XCS2 MC XCS0 MC XCS5
M STEPPING
MOTOR
TRACK 00
SENSOR
(4-39)
PK-52/50
(4-21) (4-22) S701,702,704-707,
IC702 BOARD
709,711 Note:
SHOCK
CONTENUDE ON BATT UNREG IC401 EVER 3.2V
IC404 KEY AD 1,2 FUNCTION
DETECT
FD85 model/FD90 model
(SEE PAGE SW
3-2) (4-16) ACV UNREG 3.2V REG
HI CONTROL
IC508 IC402 RESET
XCAM/PB SW
MOVIE/XSTILL SW
S708,710
PLAY/STILL/MOVIE SW
EEPROM RESET S703

XPWR SW
POWER SW
(4-21) XBATT CHG LED
XSTROBE LED D701-703
XPOWER LED
CHARGE,FLASH,POWER
(4-22) LED
CAM SO,CAM SI,XCAM SCK HI SO,HI SI,XHI SCK
32KHZ BATT
IC405 BT701
LITHIUM VANADIUM
BATTERY
TIMER
(4-22) CLOCK
IC406 EVER 3.2V

FD90 model
EEPROM
(4-24) LANC IN (4-21)
LANC OUT IC403 LANC SIG J782
BEEP
IC253 HALL AD
LANC
I/O
EXT STRB ON EXT STROBO
(4-24) AUDIO OUT FOCUS A,B

LINE/
SPEAKER XRS ON 1,2
AU SDTO
AU SDTI
IC252 AU OUT
AU IN
AMP
MIC AMP AU SP+,SP-
ZOOM SW AD
AUDIO BATT SIG

AD/DA MIC SIG
CONV. FAST CHARGE ON
BATT/XEXT
SYS DD ON
LCD DD ON
STB CHARGE KEY_ADO
VIDEO OUT J781
A/V OUT
AUDIO OUT
AU SP+,SP-
SP901
SPEAKER
(4-43/4-45)
(4-44/4-47)
IC902/ LCD901
HI SO,XHI SCK 801 IC904/901 LCD
PANEL
TIMING
EVR GENERATOR
VD,HD
Y R
R-Y IC901/802 G
MIC901 B-Y LCD B

DRIVE
MIC
(4-43/4-46)
BL UNREG
IC851,852 BL HIGH
ND901
BACK LIGHT
BACK LIGHT DRIVE
(4-41)
16
3-3 3-4
MVC-FD85/FD90
3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
FU-146/140
BATT SIG
BATT/XEXT
9 1 FC-72 BOARD
8 2
BOARD DC PACK SW
5 5
J901 FAST CHARGE ON
BATTERY 7 3 ST UNREG
TERMINAL INIT CHARGE ON
6 4
BATT UNREG CN003 CN002
1
F004 BATT SIG

BATT SIG
S 2 5 8
F006
6 7 UNREG4
3 Q001, Q002,
Q004 Q003 7 6 ACV UNREG
F002
DC PACK SW 8 5 UNREG3
4 CHARGE
SWITCH 9 4 BATT UNREG
CN002 F001
10 3 UNREG2
J902
DC IN 11 2
LF001 F005
ACV UNREG UNREG1
1 12 1
2 CN004 CN001
BATT/XEXT
3
CN001
BATT/XEXT
DC PACK SW
IC001 (4-25) FAST CHARGE ON
INIT CHARGE
L002
L001
L003
DC/DC CONVERTER
IC001 rh
VCC OUT 45
Q004
SWITCHING L007
18 VCC 5V FDD P 5V
CONTENUDE ON
1.8Vp-p
2.0µsec OUT A 46 (SEE PAGE
3-7)
17 CT +IN A 6
Q001 T001 D002

IC001 rf 16 RT SWITCHING RECT L016
15V CAM 15V
4 5
SCP:A 8 D001
1 RECT 10.5V
900mVp-p 6
2.0µsec
Q010
20 POW CONT
8
OUT B 44 EMERGENCY
21 CTL B DETECT
2 Q025,028
Q031,034
22 CTL C,D +IN B 12 -10.5V CAM -7.5V
3 -7.5V REG
L015 CAM P 5V BL UNREG
REF 2.5V
SCP:B 13 L012 FDD 4.9V FDD 4.9V
Q003
SWITCHING L005
4.9V L009 A 4.9V PANEL -15.3V
PANEL 13.2V
PANEL 6.5V
OUT C 40 Q009 PANEL 4.9V
EMERGENCY CAM 15V

DETECT CAM -7.5V
+IN C 26 CAM 3.2V
Q005-006
1.8V D 1.8V
SCP:C 24 Q002 REG
SWITCHING L004 L011
A 3.2V
L010
OUT D 39 CAM 3.2V
REF 2.5V
L008
D 3.2V
+IN D 31
Q026,029,035
Q003,004
REF 2.5V 19 V REF PANEL -15.3V
-15.3V
ZOOM/ RECT
REG
RELEASE SCP:D 29 15V

Q024,032,036,038
PANEL 13.2V D 1.8V
REF 2.5V
UNIT Q014 13.2V REG
D 3.2V
CN005 Q027,030,033,037 A 3.2V

D3.2V 10.5V PANEL 6.5V
ZOOM 4 4 4 6 6.5V REG A 4.9V
VR Q018
CN003 CN002 IC001 r; IC001 el 3.2V Q023 CAM P 5V
EMERGENCY
DETECT SW FDD P 5V
Q013,016
L017
4.9V PANEL 4.9V
800mVp-p 800mVp-p
Note:FD85 model:MVC-FD85 2.0µsec 2.0µsec
FD90 model:MVC-FD90 LCD DD ON
SYS DD ON
16
3-5 3-6
MVC-FD85/FD90
3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
TYPE ST
FD85 model
Q901,902
L903
31
FC-72 BOARD
L902
(4-43) (4-43) (4-44) (4-44)
TYPE SA
ST UNREG
IC902 IC901 IC904 IC903 LCD901
ST UNREG
8 8
LCD TIMING
Q409 (4-22) STB CHG 93
STB CHG
1 6
11 EVR
DRIVE GENERATOR
AMP
TYPE SA LCD
XSTB FUL FLASH 14 HVDD UNIT
BATT SIG
IF BLOCK
48
49
BATT SI
IC404 XSTB FULL
32
STB ON
10 5
UNIT 12
L901
7
BATT SO 9 4 VDD
HI CONTROL A 4.9V 15 CN901
4 3 TYPE ST
D402 42,51 CN301 FD90 model

ACV UNREG 3.2V
2 3 75,76 BACKUP VCC
REG 77,86 LCD901
D401 (4-21) 87 PANEL 3.2V CN901 VDD
BATT UNREG 20 31 2
IC402 L801 (4-45) (4-46)
1
VSH
LCD
IC401 IC801 IC802 IC901 IC902 22
VGL
VGH
UNIT TYPE CA
(4-21) 2 RESET 1 38 XREST 24
EVR LCD TIMING COM

DRIVE GENERATOR AMP LCD901
XPOWER 14
L903
P 4.9V (4-47) (4-43)
71 BATT SENS Q411 PANEL 4.9V VSH
POWER LED 60 LED DRIVE PANEL -15.3V

40 11
L902
13
VSS
LCD
TYPE SH
PANEL 13.2V
37 14
L901
16
VGH
UNIT
72 ACV SENS 39 12 24
PANEL 6.5V
36 15 CN901
BATT/XEXT
DC PACK SW
FAST CHARGE ON 92 DD CON SENS D 3.2V
INIT CHARGE 38 13
S703
20 BATT/XEXT CAM DD ON 25 POWER
24 27
65 DC PACK SW (4-41) (4-39)
13 38 D703
100 FAST CHARGE A 4.9V (POWER)
27 INIT CHARGE
BL UNREG
19
41
32
9
IC851,852 IC702
47 LCD DD ON
42 10 BACK LIGHT DRIVE SHOCK DETECT
29 SYS DD ON FDD P 5V J782
46 5
LANC DC LANC/
9 42 EXTSTROBO
EVER 3.2V BT701
D410 26 25 CHARGE LED LITHIUM VANADIUM BATTERY
EVER 3.2V R485 BATT
CONTENUDE ON 50 1 FD90 model
(SEE PAGE CN802 CN701
PK-52/50 BOARD
3-6) (4-22) (4-22) (4-21)
IC406 IC405 IC403

1 14
(4-17)
EEPROM TIMER BLOCK LANC I/O Q701-704 IC704 CN702
BL UNREG
FD90 model 4.9V FDD HEAD AMP 5 SIDE1 HEAD
REG
CN703
FLOPPY
FDD 4.9V R743 DISK DRIVE
3 SIDE2 HEAD
BL UNREG UNIT
FDD P 5V 9
SPINDLE MOTOR
FDD 4.9V 10
(4-18)
PANEL -15.3V
IC702 5 SENSOR
PANEL 13.2V D 3.2V CN701

PANEL 6.5V FDD CONTROL
PANEL 4.9V (4-9) (4-9)
CAM 15V CAM DD ON
CAM -7.5V
CAM 3.2V IC102 IC101 CD-248/246
A +4.9V
S/H
AGC
TIMING
BOARD
IC301 199
STB ON
Q102-105
A/D CONV.
GENERATOR
(4-8/4-6)
(4-14) (4-15) (4-16) (4-16)
(4-13) CAM -7.5V CAM -7.5V
10 14 IC201/101
CAMERA DSP
MEMORY CONTROL IC302 IC501 IC505 IC506 CAM 15V
CAM 3.3V
CAM 15V
9 15
CCD
VIDEO ENCODER IMAGER
OPD,OSD,HOST IF CN101 CN201
RES CONTROL /101
Note:
FD85 MODEL : MVC-FD85
SG,JPEG,L-MODE MC
64 Mbit FLASH ROM SDRAM FD85 modelL/FD90 model FD90 MODEL : MVC-FD90
SDRAM CAM 16Mbit 16Mbit
SH-DSP
D 1.8V D 1.8V
D 3.2V D 3.2V D 3.2V
4
FOCUS MF
RING
A 3.2V A 3.2V
CN401
UNIT
A 4.9V A 4.9V
DAC ENB
CAM P 5V
FDD P 5V
CAM P 5V
IC181 CH 3.2V
L184
FD90 model
(4-24) (4-24)
L901 L181 L182 ND FILTER
L183
IC253 IC252
DRIVE XLENS RST LED LENS
L255
SP VCC
Q901,902
(4-11) FD90 model UNIT
HI UNREG
LCD DD ON
LINE/ AUDIO Q189,190 SENS VCC FOCUS
HI VDD
RESET
SYS DD ON Q253 SPEAKER AD/DA REG 7 14 RESET

AMP CONV. SENSOR
+3.1V Q182
-LCD type check-
10 18 17 By measurimg the resistor valve between
CN803
FOR CHECK
IC901 IC183 IC182 IC184 IC185 IC186 19 8
ZOOM
RESET Pin 13 of CN803(FC-72 board) and Pin 4
SENSOR
ZOOM MOTOR of CN803(FC-72 board),type of LCD can
EVR
VIDEO DRIVE SHUTTER IRIS HALL
AMP FOCUS MOTOR DRIVE DRIVE AMP D/A be discrimimated.
DRIVE CONV.
Type SA : 10k
(4-19) (4-11) (4-11) (4-11) (4-12) (4-12) ND Type ST : 22k
25 12 FILTER Type CA :
METER
CN183 Type SH : 4.7k
16 (FD85 model)
CN184
(FD90 model)
3-7 3-8E
MVC-FD85/FD90
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A
CD-248 BOARD (FD85 MODEL)
FD85 MODEL FD90 MODEL
CN201 18P CN101 18P

CCD
IMAGER
LENS UNIT
B
VSUB_CONT
CAM_-7.5V
CAM_15V
CCD_OUT
FLASH
VSHT
-LCD type check-
GND
GND
GND
GND
V1B
V1A
V3B
V3A
RG
UNIT
H1
H2
V2
V4
By measurimg the resistor valve between
10
11
12
13
14
15
16
17
18
Pin 13 of CN803(FC-72 board) and Pin 4
2
3
4
7
8
9
of CN803(FC-72 board),the type of LCD can
C FP-167 FLEXIBLE(FD90 MODEL) be discrimimated.
FD85 MODEL
FP-231 FLEXIBLE(FD85 MODEL)
Type SA : 10k
Type ST : 22k
Type CA :
Type SH : 4.7k
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
18
17
16
15
14
13
12
11
10
10
9
8
7
6
3
2
7
6
4
3
2
1
1
2
3
4
7
8
9
ND_CONT+
ND_DRIVE+
ND_DRIVE-
TEMP_COM_(GND)
TEMP_OUT
Z_SENS_RST
Z_SENS_VCC
Z_SENS_GND
ZOOM_A
ZOOM_B
ZOOM_B
ZOOM_A
HALL-
F_SENS_VCC
F_SENS_RST
F_SENS_GND
FOCUS_A
FOCUS_B
FOCUS_A
VSHT
VSUB_CONT
RG
H1
DRIVE-
DRIVE+
HALL+
BIAS-
H2
GND
CAM_-7.5V
BIAS+
CAM_15V
V1B
V1A
V2
V3B
V3A
V4
GND
GND
FOCUS_B
CCD_OUT
GND
STB_CHARGE
STRB_PHOTO_ON
POP_UP_ON
A_4.9V
UNREG_GND
PHOTO_TR_OUT
UNREG
STRB_ON
XSTB_FULL
ND_CONT-
TALLY
CN801 50P CN701 50P CN851 20P
AV_JACK_IN 1 50 AV_JACK_IN UNREG_GND 1
VIDEO_OUT 2 49 VIDEO_OUT BL_LOW 2
26P
D
10P
18P
VIDEO_GND 3 48 VIDEO_GND BL_LOW 3
CN301
CN183
AUDIO_OUT 4 47 AUDIO_OUT LED_GND 4
CN101
AUDIO_GND 5 46 AUDIO_GND LED 5
REG_GND 6 45 REG_GND
PK-50 BOARD (FD90 MODEL) N.C 6
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
7
8
9
LANC_SIG 7 44 LANC_SIG N.C 7

PK-52 BOARD (FD85 MODEL)
DRIVE+
DRIVE-
HALL-
BIAS-
HALL+
BIAS+
Z_SENS_RST
Z_SENS_VCC
Z_SENS_GND
TEMP_COM_(GND)
TEMP_OUT
ND_DRIVE+
ND_DRIVE-
F_SENS_VCC
F_SENS_RST
F_SENS_GND
ZOOM_A
ZOOM_B
ZOOM_B
ZOOM_A
FOCUS_A
FOCUS_B
FOCUS_B
FOCUS_A
LANC_JACK_IN 8 43 XLANC_JACK_IN N.C 8
LANC_DC 9 42 LANC_DC N.C 9
EXT_STRB_ON/SENS 10 41 EXT_STB_ON/SENS N.C 10

24P
E CN803 22P CN702 5P

REG_GND 11 40 REG_GND N.C 11
1 FDDRF_B 1 SHIELD
MOVE/XSTILL 12 39 MOVE/XSTILL N.C 12
(PK-52 BOARD)
CN184
2 FDDRF_A 2 ERASE (PK-50 BOARD)

XPOWER_LED 13 38 XPOWER_LED N.C 13
3 INDEX 3 R/W_B
1/3 LK/JACK BLOCK
FD90 MODEL
4 REG_GND FC-72 BOARD (SIDE1)
4 R/W_A
XBATT_CHG_LED 14
15
37
36
XBATT_CHG_LED 1/4 LK/JACK BLOCK N.C
N.C
14
15
SHOCK SENS SHOCK SENS
5 XCPC_IN 5 COMMON 2/4 BL BLOCK 2/3 BL BLOCK
KEY_AD2 16 35 KEY_AD2 N.C 16
6 TRACK_00 1/9 CH BLOCK
KEY_AD1 17 34 KEY_AD1
3/4 RGB BLOCK 3/3 RGB/TG BLOCK N.C 17
7 HSY
2/9 LD BLOCK CN703 5P XSTROBE_LED 18 33 XSTROBE_LED BL_HIGH 18
F 8
9
COM
3/9 P2K BLOCK
5 SHIELD A_4.9V 19 32 A_4.9V 4/4 TG BLOCK BL_HIGH 19
VG
4 ERASE PANEL_3.2V 20 31 PANEL_3.2V N.C 20
10 HI_UNREG
4/9 SH BLOCK 3 COMMON PANEL_B-Y 21 30 PANEL_B-Y
11 LANC_IN (SIDE0)
CPC 2 R/W_A XCAM/PB_SW 22 29 XCAM/PB_SW
12 LANC_OUT 5/9 FDC BLOCK 1 R/W_B PANEL_Y 23 28 PANEL_Y
FLEXIBLE
13 MAKER_RECOG ND901
FD90 MODEL XPWR_SW 24 27 XPWR_SW FD90 MODEL BACK LIGHT
14 PF7/MS_SCLK 6/9 VI/CN BLOCK CN701 19P
CN401 6P PANEL_R-Y 25 26 PANEL_R-Y CN901 24P
15 TXD/MS_BS 19 DISK
1 REG_GND 7/9 HI BLOCK EVER_3.2V 26 25 EVER_3.2V
G CONTROL SWITCH 2 FOCUS_B
16 RXD/MS_DIO
8/9 AU BLOCK
18 FPTS
MAKER_RECOG 27 24 MAKER_RECOG
J781 VSH CLD 1
BLOCK(MF-330) 3 FOCUS_A
17 RESET/XMS_IN 17 HDS
VG 28 23 VG
AUDIO
(MONO)
VDD SPD 2
FP-165
18 HI_VDD/D_3.2V 16 FDD_GND VR CTR 3
4 D_3.2V/KEY_AD3 9/9 DD BLOCK HSY 29 22 HSY VIDEO
19 EVF_BL+ 15 FDD_GND OUT VB EX3 4
FOCUS 5 REG_GND PANEL_COM 30 21 PANEL_COM
20 EVF_BL_4.75 14 CLOCK VG EX2 5
6 KEY_AD0 XCS_PANEL_D/A 31 20 XCS_LCD_D/A
21 EVF_VG 13 FDD_LED_IN VSS VB12 6
PANEL_V 32 19 PANEL_V
22 EVF_VCO 12 MC J782 MODE1 RES 7
CN251 2P HI_SO 33 18 HI_SO
EXT STROBE
MIC901
1 MIC_SIG FDD 11 INDEX
HDO 34 17 HDO
MCLK TST 8
H MIC 2 MIC_GND UNIT 10

9
FDD_5V
XHI_SCK 35 16 XHI_SCK
FD90 MODEL
HCNT
CLR
VR 9
LCD901
FDD_5V VG 10 PANEL
PANEL_6.5V 36 15 PANEL_6.5V LCD
8 FDD_GND(E) OE VB 11
PANEL_-15.3V 37 14 PANEL_-15.3V
7 TOS1(C) S709 SRTL GND 12
D_3.2V 38 13 D_3.2V
6 STBY(K) LCD BACK LIGHT SRTR VSH 13
PANEL_13.2V 39 12 PANEL_13.2V
5 FDD_5V(A) VBC COM 14
PANEL_4.9V 40 11 PANEL_4.9V ON
4 PNB VCOM VGL 15
BL_UNREG 41 10 BL_UNREG
3 PNA MODE2 VSS 16
BL_UNREG 42 9 BL_UNREG
I 2
1
PB
REG_GND(UNREG_GND) 43 8 REG_GND(UNREG_GND)
OFF RESET
GSRT
MO2 17
PA S704 MO1 18
REG_GND(UNREG_GND) 44 7 REG_GND(UNREG_GND)
VOLUME + GPCK EX1 19
FDD_GND 45 6 FDD_GND
S706 GRES SPS 20
FDD_P_5V 46 5 FDD_P_5V
VOLUME - VREFL CLS 21
AU_SP+ 47 4 AU_SP+
12P
9P
VGL VCC 22
AU_SP- 48 3 AU_SP- S708
VREFH VSH 23
CN002
FAST_CHARGE_ON
INIT_CHARGE_ON
CN001
AU_SPON 49 2 AU_SPON PLAY

VGH
ZOOM_SW_AD
D501 VGH 24
DC_PACK_SW
BATT_UNREG
AU_MIXOUT 50 1 AU_MIXOUT
(ACCESS)
J
BATT/XEXT
STILL
REG_GND
REG_GND
REG_GND
REG_GND
BATT_SIG
XRS_ON1
XRS_ON2
TYPE CA TYPE SH
UNREG1
UNREG2
UNREG2
UNREG3
UNREG3
UNREG4
UNREG4
D_3.2V
S710
FD85 MODEL
MOVIE
CN901 24P
10
11
12
9
8
7
5
4
3
2
4
5
7
8
9
S703
POWER NC TESTL 1
CN702 2P
FU-52 FU-51 SP901
1 SP +
S705 COM COM 2
HARNESS HARNESS SPEAKER 2 (FLASH)

STH VST 3
SP -
XSTH VCK 4
K
12
11
10
1
2
3
5
6
7
8
9
8
6
5
4
3
S711 CKH1 EN 5
SP-149 (MACRO) CKH2 DWN 6
XRS_ON1
XRS_ON2
ZOOM_SW_AD
D_3.2V
INIT_CHARGE_ON
(3.2/1.8/HI) UNREG1
(FLASH)UNREG2
(FDD_P_5V) UNREG2
UNREG3
(TRANS,4.9V)UNREG3
UNREG4
(BL/STP) UNREG4
REG_GND
REG_GND
REG_GND
REG_GND
DC_PACK_SW
FAST_CHARGE_ON
BATT/XEXT
BATT_SIG
BATT_UNREG
CN001 3P
HARNESS HVDD VDD 7
S707
ACV_UNREG 1 J902 PROGRAM AE GND VSS 8
DC IN
12P
ACV_GND 2 VVDD VDDG 9

9P
S702
CONTROL SWITCH 6 UNREG_GND
BATT/XEXT 3 DISPLAY XSTV VSSG 10
LCD901
PANEL
BLOCK
CN003
CN004
5 ZOOM_SW_AD LCD
STV CS 11
(ZOOM BLOCK 330) 4 D_3.2V S701
CKV2 WIDE 12
L RV001
S001 3 UNREG_GND
CN002 4P
MENU
CKV1 HST 13
(FREEZE) 2 XRS_ON2
ZOOM XENB REF 14
(SHUTTER) 1 XRS_ON1 BATT_UNREG 1 D702
D703 ENB SDUT 15
CN005 6P BATT_SIG 2 J901
BATTERY ON/CHG XPCG CRext 16
FD85 MODEL:MVC-FD85
FD90 MODEL:MVC-FD90 FU-140 BOARD (FD90 MODEL) BATT_GND
DC_PACK_SW
3
4
TERMINAL
PCG HCK2 17
FU-146 BOARD (FD85 MODEL) D701 CSV HCK1 18

16 (FLASH) PCD PSIG 19
G G 20
M BT701
LITHIUM
R R 21
BATTERY B B 22
CSH RGT 23
NC TESTR 24
TYPE SA TYPE ST
FRAME SCHEMATIC DIAGRAM

4-1 4-2
MVC-FD85/FD90 MVC-FD85/FD90
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS

(In addition to this, the necessary note is printed in each block)
(For printed wiring boards) (Measuring conditions voltage and waveform)

• b: Pattern from the side which enables seeing. • Voltages and waveforms are measured between the measure-
(The other layers' patterns are not indicated.) ment points and ground when camera shoots color bar chart of
• Through hole is omitted. pattern box. They are reference values and reference wave-
• Circled numbers refer to waveforms. forms. *
• There are few cases that the part printed on diagram (VOM of DC 10 MΩ input impedance is used.).
isn’t mounted in this model. • Voltage values change depending upon input impedance of VOM
• Chip parts. used.) *
Transistor Diode
C 65 4 45 6 4 5 1 2 3 3 3 1. Connection
Pattern box
B E 12 3 32 1 32 1 54 3 2 1 2 1 2 1
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µµF.
50V or less are not indicated except for electrolytics and Approx. 97 cm (MVC-FD85)
tantalums. 1.5 m (MVC-FD90)
• Chip resistors are 1/10W unless otherwise noted.
kΩ=1000Ω, MΩ=1000kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor, Be-
cause it is damaged by the heat.
• Some chip part will be indicated as follows. Front of the Protection glass
Example C541 L452
22U 10UH
TA A 2520
2. Adjust the distance so that the output waveform of Fig. a and

Kinds of capacitor the Fig. b can be obtain.
Temperature characteristics H
Yellow
External dimensions (mm)
Magenta
White
Cyan
Green
• Constants of resistors, capacitors, ICs and etc with XX indicate
Red
Blue
that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
• Signal name A B A=B B A
XEDIT → EDIT PB/XREC → PB/REC Fig. a (Video output terminal output waveform)
• 2 : non flammable resistor
• 1 : fusible resistor
• C : panel designation Electron beam
• A : B+ Line * scanned frame
• B : B– Line *
Magenta
Green
Yellow
White
Cyan
•J
Blue
: IN/OUT direction of (+,–) B LINE. *
Red
• C : adjustment for repair. * CRT picture frame
• Circled numbers refer to waveforms. *
* Indicated by the color red.
Note : Note : Fig.b (Picture on monitor TV)
The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une When indicating parts by reference number, pleas include
specified. pièce portant le numéro spécifié. the board name.
4-4
MVC-FD85/FD90
CD-246 (CCD IMAGER)(FD90 MODEL) PRINTED WIRING BOARD For schematic diagram
— Ref. No. CD-246 Board; 2,000 Series — • Refer to page 4-55 for waveforms.
1 2 3 4 5 6 7
CD-246 BOARD (FD90 MODEL) R112

0
CN101 18P
1 VSHT
CCD IMAGER
A -REF.NO.:2000 SERIES-
2 VSUB_CONT
3 RG
XX MARK:NO MOUNT 4 H1
NO MARK:REC/PB MODE 5 H2
R111 XX R101 0
XX
R :REC MODE
6 GND
P :PB MODE TO
D101
7 CAM_-7.5V FC-72 BOARD
CN101
8 CAM_15V (THROUGH THE FP-167
FLEXIBLE)
9 V1B
(SEE PAGE
B 10
11
V1A
V2
4-9)
12 V3B
13 V3A
14 V4
15 GND
L101
100uH 16 GND
17 CCD_OUT
C C101 R102 0
18 GND
10u C102
20V 22u
TA B 16V
B
TA
C103
1 IC101 0.01u
25V
R104
R105
7
R103
B
CCD IMAGER
C104
IC101 0.1u
6
39
39
220
ICX232AQ-13 B
D R-7.1/P0
10 11 12 13 14 15 16
H2
1
V4
R-7.1/P0 R1.4/P0
H1
UN9213J-(K8).SO
2
V3A
R-7.1/P0 R1.8/P0 0
2 RG
3
V3B
Q101
C105 0.1u
INV.
R-0.4/P0 R13.7/P0 16V B R106
VL
4
V2 3300
R-0.4/P0 R-7.5/P0
CSUB
5
V1A R110
R-0.4/P0 R8.0/P0 47
3 VSHT
6
V1B
R7.6/P0
GND
7
GND
C106
C111 R107
R8.0/
P0
E VDD 0.1u
9
VOUT XX 1M
16V SIGNAL PATH
R10.4/P0
R14.8/P0
For printed wiring boards C109
B
B
C107
R10.4/
10p
• Refer to page 4-59 for parts location. CH 0.1u VIDEO SIGNAL
2SC4178-F13F14-T1
16V B
P0
• This board is four-layer print board. However, the pat- 4 CHROMA Y Y/CHROMA
BUFFER
5 C108
Q102
R108
terns of layers two and three have not been included 3300 0.1u
25V
PK-50 (MVC-FD90) CD-246 (MVC-FD90) F REC
in the diagram.
R14.8/
P0
R9.7/
P0
• Chip parts PK-52 (MVC-FD85) C110 XX PB
F R109
Transistor 0
C 16
B E
Precautions Upon Replacing CCD Imager
There are few cases that the part printed on this • The CD-246 board mounted as a repair part is not equipped
diagram isn’t mounted in this model. FC-72 with a CCD imager.
When replacing this board, remove the CCD imager from the
old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the adjust-
ments for the camera section.
• As the CCD imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
CCD IMAGER
4-5 4-6 CD-246 (FD90 MODEL)
MVC-FD85/FD90
CD-248 (CCD IMAGER)(FD85 MODEL) PRINTED WIRING BOARD For schematic diagram
— Ref. No. CD-248 Board; 3,000 Series — • Refer to page 4-56 for waveforms.
1 2 3 4 5 6 7 8
CN201 18P
1 VSHT
A CCD IMAGER R212

0 2 VSUB_CONT
3216
-REF.NO.:3000 SERIES- 3 RG
XX MARK:NO MOUNT 4 H1
5 H2
NO MARK:REC/PB MODE R211 XX R201 0
D201 XX
R :REC MODE 6 GND
P :PB MODE 7 CAM_-7.5V TO
FC-72 BOARD
8 CAM_15V CN101
(THROUGH THE FP-231
9 V1B FLEXIBLE)
B 10 V1A
(SEE PAGE
11 V2 4-9)
12 V3B
13 V3A
14 V4
15 GND
C201 16 GND
L201 10u
100uH 20V 17 CCD_OUT
2520 TA B R202 0
C C202
18 GND
220
22u
1
R205 39
IC201 16V
TA B
R203
CCD IMAGER
7 R204
C204
0.1u C203
IC201 ICX202BQ-13 39 2012 B 0.01u
R-7.1/P0
25V
B SIGNAL PATH
10 11 12 13 14 15 16
H2
1
V4
C205
R-7.1/P0 R1.4/P0
0.1u VIDEO SIGNAL
47k
47k
UN9213J-(K8).SO
H1
2
V3A 16V B
R-7.1/P0 R1.8/P0
2 RG
0
CHROMA Y Y/CHROMA
3
V3B
D R-0.4/P0 R13.7/P0
VL
R206
4
V2
Q201
6800
REC
INV.
R-0.4/P0 R-7.5/P0
CSUB
5
V1A
R8.0/P0 R210 47
R-0.4/P0
3 VSHT PB
6
V1B
R7.6/P0
GND
7
GND
C211 R207 C206
R8.0/
P0
VDD 0.1u
9
VOUT XX 1M
B 16V
R10.4/P0
R14.8/P0
1608
C207 B
2SC4178-F13F14-T1
R10.4/
0.1u
16V B C208
4
P0
0.1u
BUFFER
E C209 R208
Q202
25V
For printed wiring boards 10p
CH 3300 5 6 F
• Refer to page 4-59 for parts location.
R14.8/
P0
R9.7/
P0
• This board is four-layer print board. However, the pat- C210 XX
terns of layers two and three have not been included CD-248 (MVC-FD85)
R209
in the diagram. 0
• Chip parts FU-140 (MVC-FD90)

FU-146 (MVC-FD85)
F
Transistor
C 16
B E Precautions Upon Replacing CCD Imager

• The CD-248 board mounted as a repair part is not equipped
There are few cases that the part printed on this FLASH UNIT with a CCD imager.
diagram isn’t mounted in this model. When replacing this board, remove the CCD imager from the
old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the adjust-
ments for the camera section.
• As the CCD imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
CCD IMAGER
CD-248 (FD85 MODEL) 4-7 4-8
MVC-FD85/FD90
Schematic diagram and printed wiring board of the FC-72 board are not shown.
Pages from 4-9 to 4-30 are not shown.
MVC-FD85/FD90
PK-50 (AV OUT/KEY IN, BACK LIGHT, RGB, TG)(FD90 MODEL) PRINTED WIRING BOARD
— Ref. No. PK-50 Board; 5,000 Series —
For printed wiring boards

• This board is four-layer print board. However, the pat-
terns of layers two and three have not been included
in the diagram.
• Chip parts
Transistor Diode
C 65 4 45 6 4 5 1 2 3 3
B E 12 3 32 1 32 1 54 3 2 1 2 1
There are few cases that the part printed on this

diagram isn’t mounted in this model.

PK-52 (MVC-FD85)
FC-72
AV OUT/KEY IN, BACK LIGHT, RGB, TG

PK-50 4-31 4-32
MVC-FD85/FD90

4-33 4-34 PK-50
MVC-FD85/FD90
PK-52 (AV OUT/KEY IN, BACK LIGHT, RGB, TG)(FD85 MODEL) PRINTED WIRING BOARD
— Ref. No. PK-52 Board; 6,000 Series —

terns of layers two and three have not been included
in the diagram.
• Chip parts
Transistor Diode
C 65 4 45 6 4 5 1 2 3 3
B E 12 3 32 1 32 1 54 3 2 1 2 1
There are few cases that the part printed on this


PK-52 (MVC-FD85)
FC-72

PK-52 4-35 4-36
MVC-FD85/FD90

4-37 4-38 PK-52
MVC-FD85/FD90
For schematic diagram

• Refer to page 4-31, 35 for printed wiring board.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
(FD90 MODEL) NO MARK:REC/PB MODE
PK-50 BOARD(1/4) R :REC MODE
PK-52 BOARD(1/3) (FD85 MODEL) P :PB MODE FD85 MODEL:MVC-FD85 SIGNAL PATH
A REC/PB AMP(REF BLOCK)
FD90 MODEL:MVC-FD90
VIDEO SIGNAL
AUDIO
-REF.NO.:10000 SERIES- CHROMA Y Y/CHROMA SIGNAL
XX MARK:NO MOUNT
REC
R782
CN701 50P FB788 J781
1k
0uH PB
AV_JACK_IN 50 AUDIO
VIDEO_OUT 49 (MONO)
FB789 0uH VIDEO
VIDEO_GND 48 OUT
B AUDIO_OUT 47
R787
1k C781
FB790
0uH
XX
AUDIO_GND 46
REG_GND 45 C782 C783 FB791
XX XX 0uH
LANC_SIG 44 D785
MA111-(K8).S0
XLANC_JACK_IN 43
LANC_DC 42
EXT_STB_ON/SENS 41 D786 D788
MA4Z082WA-(TX).SO MA4Z082WA-(TX).SO FB787
REG_GND 40 D787 0uH LND783
C MOVE/XSTILL 39
MA4Z082WA-(TX).SO
FLAME_GND
XPOWER_LED 38
CHARGE LED(AMBER) LND784
XBATT_CHG_LED 37
D702 FLAME_GND
SHOCK SENS 36
TLYU1002(TPX1,SONY)
KEY_AD2 35
KEY_AD1 34
XSTROBE_LED 33
A_4.9V 32
D PANEL_3.2V 31
R710
PANEL_B-Y 30 270
TO
FC-72 BOARD XCAM/PB_SW 29
CN801
(THROUGH THE PANEL_Y 28 FD90 MODEL
FP-165 FREXIBLE)
XPWR_SW 27
FB782 0uH
(SEE PAGE PANEL_R-Y 26
4-20) FB783 0uH
EVER_3.2V 25 FD90 MODEL
MAKER_RECOG 24 PANEL_B-Y 8 TO(3/4) PLAY MOVIE FB784 0uH
E
TLGU1002(TPX1,SONY)
TLYU1002(TPX1,SONY)
VG 23 PANEL_Y
8 TO(3/3) POWER STILL FB785 0uH
HSY 22 PANEL_R-Y J782
S703 S708 S710
PANEL_COM FD85 MODEL EXT STROBE
21 MAKER_RECOG
D703
0uH
D701
FB786
11 TO(4/4)
XCS_LCD_D/A 20 HSY
PANEL_V 19 PANEL_COM 13 TO(4/4)
HI_SO 18 PANEL_V R705 R713 SB-C4241
680 680 D784
HDO 17 HDO MA111-(K8).S0
R726 D782 D783 D789 D790 LND781
XHI_SCK 16 VG 9 TO(3/3) FLASH LED(AMBER) 10k
F PANEL_6.5V 15 HSY POWER LED(GREEN) MA4Z082WA-(TX).SO MA4Z082WA-(TX).SO FB781
GND
MA4Z082WA-(TX).SO MA4Z082WA-(TX).SO
PANEL_-15.3V 14 PSIG LND782
D_3.2V 13 HDO GND

16 TO(4/4)
C705
PANEL_13.2V 12 PANEL_V FD90 MODEL 22u SE701
6.3V
PANEL_4.9V 11 HI_SO 15 TO(3/4) C710
0.1 0.47u
10
S1A
1
BL_UNREG 10 XCS_PANEL_D/A IC702 TRIP B
15 TO(3/3) 0.1 0.9 R714
S1B TA6009FN(EL)
2
IC702
9
BL_UNREG 9 XHI_SCK AO 11k
R704 1.2
FD85 MODEL C706 XX
0.5 ± 0.5%
3 GUARD
8
REG_GND(UNREG_GND) 8 MAKER_RECOG 10 TO(3/3) 0.22u B BI
G 3.0
OUT
1.2
R715
4
7
REG_GND(UNREG_GND) 7 PANEL_13.2V BO 150k SHOCK FD90 MODEL FD85 MODEL
R703 3.1 SENSOR
18 TO(3/3) GND
5
6
FDD_GND 6 PANEL_3.2V 0 VCC AMP S711 S711
C711
FDD_P_5V 5 REG_GND 68p
CH S702 FOCUS
AU_SP+ 4 PANEL_3.2V S704 S706
LND701 (MACRO)
R716 R718
AU_SP- 3 PANEL_13.2V 1800 DISPLAY VOLUME (+) VOLUME (-)
DUMMY 2700
L702
AU_SPON 2 PANEL_-15.3V 19 TO(4/4) 47uH
2520 R720 R722
AU_MIXOUT 1 PANEL_4.9V 4700 6800 R724
12 TO(3/3) GURUPON SWITCH 33k
REG_GND FD85 MODEL
H CN702 2P D_3.2V 12 TO(3/4,4/4)

FD90 MODEL
SB-N6355
SP + 1 COMMON
SP901
SPEAKER SP - 2 8
UP SET
S701 1 7
PANEL_3.2V
PANEL_6.5V 17 TO(3/4) C701 IC701 C707 C708
XX XX
MENU
LEFT 2 RIGHT FD90 MODEL
XX 10V B 6
REG_GND FD90 MODEL B R709 R711
XX XX 3 TO(2/4)
PANEL_4.9V 2 TO(2/4) C702 COMMON DOWN
XX IC701 XX 3 5 STATIC2
BL_UNREG 10V
I 2 TO(2/3) GND
3 TO(2/3)
10 11 12 13 14
1
BL_GND VCC R706 4

FD85 MODEL C703 XX
R728 XX NC R712
2
NC S705 FD85 MODEL

XX B XX R717
SPOUT-2 1800 COMMON
3
SP IN
R727 SPOUT-1 S707
4
XX AUX (FLASH) S709

C704 XX B C709 PROGRAM AE
BIAS
5
AM XX LCD
R702 XX
EVR R719 R721 BACK LIGHT
6
SUSPEND
2700 4700 R723 R725
NC
7
NC R707 6800 33k

L701 ON
XX
XX
J
16 OFF
R729 BT701
0
(LITHIUM BATTERY)
AV OUT/KEY IN
PK-50 (1/4), PK-52 (1/3) 4-39 4-40
MVC-FD85/FD90

• Refer to page 4-31, 35 for printed wiring board.
1 2 3 4 5 6 7 8 9 10 11 12 13
PK-50 BOARD(2/4) (FD90 MODEL) NO MARK:REC/PB MODE

PK-52 BOARD(2/3) (FD85 MODEL) R :REC MODE
P :PB MODE
A BACK LIGHT(BL BLOCK)
-REF.NO.:5000 SERIES-(FD90 MODEL)
Q856
-REF.NO.:6000 SERIES-(FD85 MODEL) FP102-TL R867 CN851 20P
Q854 1800 T851
XX MARK:NO MOUNT 2SD2216J-QR(K8).SO
SWITCHING
1/10W
2012 20 N.C
SWITCHING 4.8
7.1 3
4 5 19 BL_HIGH
BL_UNREG L852 L853
2 C866
L851 6.6 22uH 100uH 18 BL_HIGH
R857 5 1 12p
4.7uH 1 3000V
22k 7.1 17 N.C
2520 1 SL
B C852
2 R868
1800
2 6 16 N.C
22u R856 6.9 6.6 1/10W C864 15 N.C
16V 560 2012 0.015u 3
C853 3
TA B 0.22u 2012 14 N.C
F C856 C859 4.6 4.6
FD90 MODEL R858 4 10 13 N.C
18p 27p 4 5
560 -0.4 ND901
CH CH
C861 3 1 12 N.C
2 TO(1/4) C862 BACK
33u 1u Q860 -0.4 LIGHT
11 N.C
10V F FP216-TL
TA B SWITCHING 2
10 N.C
2 TO(1/3) OSC
BL_GND 9 N.C
C FD85 MODEL 8 N.C
2
Q852 Q851,852 D852 Q861
BL-LEV XX 7 N.C D901
UN9112J-(K8).SO UN9112J-(K8).SO
1
SWITCH R873 (STARTER)
LED DRIVE 120 6 N.C
4.9 4.9 4.9 0
PANEL_4.9V 5 LED
3
1
3
1 R860 C860
R855 4 LED_GND
120k 10k XX
R876
± 0.5% ± 0.5%
68k
R864 3 BL_LOW
2
2
0 47k 4.8
2 BL_LOW
LND851
FD85 1 UNREG_GND
D SHIELD_GND MODEL C858
0.01u
R859
4700
3.6
4.9
1.2
1.0
LND852 R869
100k
SHIELD_GND
LND853
1 2 3 4
IC851 R861
OUT
1800
VCC
0
RN1107F(TPL3)
FB
1 ± 0.5%
IN
C857
SWITCHING
TL5001CD-E2
SHIELD_GND 0.022u
2 REG.
Q851
LND854
C851
1.7
SHIELD_GND 0.01u
R852 3
XX
2SD2216J-QR(K8).SO
R851 Q858
IC851
LND855 2SD2216J-QR(K8).SO
XX NJM2406F-TE2:FD90 MODEL
GND
DTC
SCP
RT
TA75S393F-TE85R:FD85 MODEL
1.0
STATIC_GND IC852
1 1 0.9
LND856 D853
2 2 MA111-(K8).S0
8 7 6 5 1.4
Q857
Q853 2 1
3
FLAME_GND D851 0.9
FD90 MODEL UN9213J-(K8).SO
2.3
0.9
0.9
XX 0 4.8
SWITCH 1 0.6 1
2
3 3
1 0.3
0.3
2 2 0.3 R871 C865 R872
3 TO(1/4) STATIC2
1
0
2 R865 R866 22k 0.1u 470

0 R862 4.9
2.6 3300 4700 1500
± 0.5% R863 Q859
3 TO(1/3) 3 1500 3 UN9213J-(K8).SO
3
F FD85 MODEL Q855
SWITCH
R853 R854 C854 C855 C863 R870

6800 27k 2.2u 2.2u UN9213J-(K8).SO Q857,858 0.1u 6800
FD90 MODEL ± 0.5% ± 0.5% 6.3V
TA A
F
2012 SWITCH IC852
4 TO(3/4) BL_LEV
CURRENT
DETECT
4 TO(3/3) BL_LEV
FD85 MODEL
Note : Note :
G
FD85 MODEL:MVC-FD85 The components identified by Les composants identifiés par
FD90 MODEL:MVC-FD90 mark 0 or dotted line with mark une marque 0 sont critiques
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.
H 16
BACK LIGHT
4-41 4-42 PK-50 (2/4), PK-52 (2/3)
MVC-FD85/FD90

• Refer to page 4-35 for printed wiring board.
• Refer to page 4-56 for waveforms.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
PK-52 BOARD(3/3) (FD85 MODEL)

RGB DRIVER/TG(RGB/TG BLOCK) * R912 -LCD type check-
A -REF.NO.:6000 SERIES- 3.1 3.1 By measurimg the resistor valve between
XX MARK:NO MOUNT * Q902 L902

100uH
IC903 Pin 13 of CN803(FC-72 board) and Pin 4
R903 of CN803(FC-72 board),the type of LCD can
NO MARK:REC/PB MODE * 0
0 2520 AMP
be discrimimated.
R :REC MODE 13.5 C907
P :PB MODE * R904 * C906 22u L903 Type SA : 10k
47uH
D901
6.3V
2520
IC903 Type ST : 22k
D902 TA A NJM062V(TE2)
XX XX * Q901 *
R947
6.1
VCC+
8
PANEL_3.2V OUT1 13.5 R949 D904
* R901 * R945
B PANEL_13.2V OUT2
47k 1T369-01-T8A
7
L901 C921 6.1 IN1- 5.6 C928
R937 R951 R956
10uH 0.1u 10k C924 0.001u
R984 10k IN2- 0.01u 33k
2520
6
R914
R916
R920
R923
47k 13.5 IN1+
33k
33k
33k
18 R913 R946 6.1 2.8 C925 L904
*
22k ± 0.5% R927 6.6
6.6 xx 4.7u R953
6.8uH
IN2+ 10k
5
TO(1/3) 47k C901 6 VCC- 2012
4 2.8 R957
3.3u C918 C919 1k
R983 6.1 5 2 10u 3.3u C926 C927
R910 XX 20V C902
TA A 6.3V C923 3300p 56p
22k R928 0.01u TA A TA A 0.1u R948 R950
47k 13.5 6.1 6.1 PSIG 27k 68k
3 1
6 4
Q904 R987
REG_GND 6.1 2 5.5
5
COLOR
33k
0
R952
BRT_R
* R954
XP4601-TXE
C
BRT_B
R915 R917 R921 R924 R985 VREF VCO
XX
R982
47k 47k * 47k * 0 Q903
* R961
* R958
* R959
* R960
R955
± 0.5%
XP4601-TXE 1 3 P_XVD
B_LIM
5.5
PRG
FRP
SBLK
R930
C903 10k C922
0.1u
3.0
3.0
2.1
3.1
3.0
1.5
1.5
3.0
0.1u
0
3.1
1.7
1.7
1.5
1.6
1.6
1.8
1.5
0.9
6.1
13.5
0
36 35 34 33 32 31 30 29 28 27 26 25
36 35 34 33 32 31 30 29 28 27 26 25
HPOS1
HPOS0
XVD
SLSH2
RPD
GND
TEST
SLSH1
CKO/TEST
CKII
TEST/CKO
SLSH0
CN901 24P
7
PRG
GAMMA2
GAMMA1
WHITE.LIMIT
FRP
RGBBLK
BLACK.LIMIT
VREF
VCC2
PSIGGRAY
SUB.BRT.R
SUB.BRT.B
D BRT
R905 1 TESTL NC
10k 6 VCOM
2 COM COM
2.8 0
R902 R911 P_XHD
8
48 47 46 45 44 43 42 41 40 39 38 37
13 14 15 16 17 18 19 20 21 22 23 24
R931
27k 100k 5 6.0 100 VB 3.0 XHD
9 VST/STH 3.0
3 VST STH
48 47 46 45 44 43 42 41 40 39 38 37
13 14 15 16 17 18 19 20 21 22 23 24
C912 4 VCK XSTH
TEST 6.1 PSIG.OUT B.OUT 1.9 R941 3.1 HPOS2 VCK/XSTH 1.5 LCD901
2.2u 2012 XX
R932 5 EN CKH1 PANEL
3.1 XTEST B.DC.DET 100 XWIDE EN/CKH1 1.5 R962 0
CONT C904 0.1u 1.5 BRIGHT

4 G.OUT
6.0
1.9 2.2u
C913
2012
VG
R942 NTSC
0
3.1 HPOS3 IC904 10 DWN/CHK2 3.0 R963 0 * C931 * R981
6 DWN CKH2
LCD
R933 *
1.3 CONTRAST IC901 G.DC.DET 6.1 100 VR 3.0 NT/PAL TIMMING GENERATOR TESTI/XSTV 3.1
7
8
VDD
VSS
HVDD
GND
PSIG.DET ROUT C914 HPOS4 VDD
E C905
2.2u
1.9
SUB.CONT.B LCD DRIVER R.DC.DET
1.9 2.2u 2012
C915
R943
*
3.1
VDD
* IC904
TEST/STV
0
1.5
* R974 C929
* * R980 9 VDDG VVDD
* R938
2012 2.2u V_REV 3.1 2012 * D906
R934 R939 R944 10 VSSG XSTV
SUB.CONT.R IC901 GND2 XX F 220k 100k VREV WIDE/CKV2 1.5 * R968
SHA R906 100 3.1 VCC1

CXA8116R-T4 3 GND1
± 0.5% 2012
6.3
13.5 Q905
XP4601-TXE
XHDO
H_REV
0.2
3.1 HDO 11 HST/CKV1 0.4 * R969
* R979
11 CS STV
C920 12 WIDE CKV2
SHB R907 100 0.5 SHA
2 SYNC.OUT 3.1 1 3 6.3 0.1u D903 COMTST HREV NC/XENB 2.7
5.8
0
SHG R908 100 0.5 SHB 1 SYNC.IN
3.0 2
5
C917
4.7u
XX
3.0
COMTST NC/ENB 2.9
13 HST CKV1
16V 14 REF XENB
R936
SHG EXT.BGP TA A VCOM XCLR NC/XPCG
39k
SHR R909 100 3.1 5.7 * R970
6 4
R935 C916 15 SDUT ENB
SHR SYNC.SEP
HCK1/XCSV
0.5 R940 * R971
RGT/XCSH
HCK2/PCG
1M 2.2u
H.FILTER.OUT
± 0.5% F 22k 16 CRext XPCG

H.FILTER.IN
AGC.FILTER
* R972
F
AGC.LEVEL
2012
R/R-Y/CR
XCLP
SBLK
AGC.OUT
REG.OUT
B/B-Y/CB
PICTURE
17 HCK2 PCG
GND
SHR
SHG
PRG
SHB
SHA
FRP
COLOR
R964 0
XRGB
18 HCK1 CSV
PSIG
G/Y
* R965
1 2 3 4 5 6 7 8 9 10 11 12 19 PSIG PCD
VG
2 3 4 5 6 7 8 9 10 11 12 G G
3.0
0.5
3.1
0.5
0.5
0
3.1
1.5
0
0
0.2
1 VR 20
R R
1.8
3.1
1.4
1.8
2.0
2.0
1.2
VB 21
22 B B
23 RGT CSH
R918 * R966
XX R922
XX * R975 24 TESTR NC
C911
G 0.1u
R929 * R967 * R973 TYPE ST TYPE SA
R919 R986 * R977
R926 100k
XX XX
XCLP
4.7k
XCLP
13.5
SHR
SHG
SHB
SHA
1 1 13.5
SBLK
PRG
2 2
FRP
* Q908
0 0 * R976
COLOR
3 3
COM
Q906 Q907
XX XX
H
IC902
C908 MB40D001PFV-G-BND-ER TYPE SA TYPE ST TYPE SA TYPE ST TYPE SA TYPE ST
0uH BRT
0.01u 1.5 VG 2200p R938 68k 47k R973 6.8k XX
FB901 VSS
13 14 15 16 17 18 19 20 21 22 23 24
VG
1
COLOR BRIGHT C906 50V XX

PANEL_Y 1.3 3.1 PSIG B R942 0 XX R974 XX 150k
C909 VDDA PSIG
2
FB902 0uH BRT_R COLOR EN

8 0.01u 1.5 EN
3.1 XHDO 0.22u R943 XX 0 R975 XX 470k
PANEL_R-Y 9 TO(1/3) HSY
3
C910 BRT_B BRT_R C929 XX 16V

TO(1/3) 0uH 1.6 SO P_XVD B R945 56k 39k R976 XX 33k
FB903
4
0.01u PANEL_V
PANEL_B-Y CONT BRT_B 2.6 SI
1.3 SI P_XHD 1u R947 150k 330k R977 XX 56k
HDO
5
B_LIM CONTRAST SCK C931 XX 10V

I 0.9 SCK
2.8
IC902
B R954 XX 0 R979 XX 0
6
VREF B.LIMIT 0 COMTST

1.5 COMTST D906 XX RD3.3UM-T1 R958 XX 0 R980 XX 0
7
VCO P_GRAY 3.1 NTSC EVR

1.5 NTSC IC904 LC12017-52 CXD351OR R959 0 XX R981 0 XX
8
4
COM
1.5
VCO
V_REV
3.1 V_REV
SIGNAL PATH Q901 UN9213J-(K8) XX R960 XX 0 R985 82k 47K
9
COM 3.1 H_REV

1.8 H_REV Q902 SI2301DS-T XX R961 xx 0
12 11 10
TO(2/3) BL_LEV VIDEO SIGNAL

TEST BL_LEV 3.1
3.1 VCC Q908 XX 2SA1832F-Y R965 XX 0
BRT_TST 3.1
VDD CHROMA Y Y/CHROMA R901 0 XX R966 XX 0
P_MUTE
R903 100k XX R967 6.8k XX
REC
J 12
R904 100k xx R968 0 XX
PB R912 XX 0 R969 0 XX
TO(1/3) D_3.2V R921 47k 33k R970 0 XX
C932 0.1u
R923 39k 33k R971 0 XX
SCK
XHI_SCK R925 10k 22k R972 0 XX
15 EN
XCS_PANEL_D/A
TO(1/3) SI
HI_SO * R925
10
MAKER_RECOG
TO(1/3)
K
16
RGB DRIVER/TG
PK-52 (3/3) 4-43 4-44
MVC-FD85/FD90

1 2 3 4 5 6 7 8 9 10 11 12 13
PK-50 BOARD(3/4) (FD90 MODEL) NO MARK:REC/PB MODE (Note)

Note:Refer to page 4-48for
LCD type check.
R :REC MODE R817
RGB DRIVER(RGB BLOCK) P :PB MODE 5.6k:Type CA
12k :Type SH
A -REF.NO.:5000 SERIES-
XX MARK:NO MOUNT
COM_ADJ
AMP
FRPV
FRPT
BRT_R
BRT_B
PANEL_6.5V
C811 L802
R808 R812 R813 R817 10u 10uH C813
22k 47k 15k 10V 2520 0.1u
F
B R818
TA
BL_LEV
4 TO(2/4)
17 TO(1/4) 39k BL_LEV
L801 R809 R814
100uH 12k 33k
2520 C812
10u
PANEL_3.2V 10V
IC801
C801 MB40D001PFV-G-BND-ER TA A
0.1u C807
F 47u 6.3V
C808 P_4.9V 5 TO(4/4)
2.9 0 0.1u
TA B
13
12
REG_GND VDD P_MUTE F
3.1 2.9
1.8
1.0
0.7
2.2
1.7
1.5
1.5
1.5
4.9
6.6
14
11
VCC BRT_TST
C802
C 0.1u H_REV 3.1 1.7 BL_LEV 36 35 34 33 32 31 30 29 28 27 26 25
15
10
F H_REV BL_LEVEL
COM_AMP
GAMMA2
GAMMA0
RGB_AMP
FRP
COM_FRP
OUT_LIM
VSH
VCC2
SUB_BRT_R
SUB_BRT_B
COM_BLK_LVL
V_REV 3.1 1.6 V-COM
16
9
V_REV V-COM
12 TO(1/4,4/4) D_3.2V NTSC 3.1 17 1.2 VCO
8
NTSC VCO
COMTST 0 1.2 COM_ADJ 17

18
48 47 46 45 44 43 42 41 40 39 38 37
13 14 15 16 17 18 19 20 21 22 23 24
7
COMTST COM_ADJ COM_BLK B_OUT VB
C806 2.9 2.5 C814
2.8 1.5 AMP 0.1u XTEST B_DC_DET 0.33u
19
1.9 B
6
XHI_SCK CLK RGB_AMP 1.9
BRIGHT 16 G_OUT
2.5 C815
VG
D
2.6 2.1 2.1
IC802
20
0.33u
5
HI_SO SI CONT CONTRAST G_DC_DET
15 TO(1/4) COM-O 3.2 1.9 B
1.7 BRT_B R803 COM_OUT LCD R_OUT VR
21
2.5
4
SO BRT_B 0 DRIVER C816
SUB_CON_B R_DC_DET COM-O
3.1 2.2 BRT_R IC802 15 1.9
0.33u
B COM-O
22
3
XCS_PANEL_D/A XEN BRT_R SUB_CON_R IR3Y37A4 GND1
2.9
2.9 1.1 COLOR VCC1 GND2 FRPV
23
7 TO(4/4)
2
VDDA COLOR FRPV
1.9
OSD_B
13 SYNC_OUT FRPT
FRPT
24
VSS BRIGHT OSD_G SYNC_IN

2.9
0
OSD_R 12 14 EXT_BGP
2.9 COMTST
E IC801 BLACK_IN SYNC_SEP COMTST
Y/CR/XRGB_SW
NTSC
NTSC
IC803 V_REV
EVR
AGC_OUT
REG_OUT
R/R-Y/CR
H_FIL_IN
AGC_LVL
B/B-Y/CB
TC7SH32FU-TE85R
PICTURE
V_REV
AGC_FIL
COLOR
INB H_REV
H_FIL
0 VCC H_REV
G/Y
1
5
V-COM
0 4.9 V-COM
INA VCO
2
OUT 1 2 3 4 5 6 7 8 9 10 11 12 VCO
3
4
0
1.8
2.9
0.7
1.1
1.8
1.9
1.9
1.2
GND
F IC803
R805 C809
OR GATE R806 XX
XX XX R821
6.3V 10k
TA COLOR
C810
0.1u
R807 R819 R820
XX XX 100k
P_XHD
6 TO(4/4)
FB801 C803 W_MSK
0uH 0.01u
G 8 TO(1/4)
PANEL_Y FB802
0uH
C804
0.01u
PANEL_R-Y FB803 C805
PANEL_B-Y
0uH 0.01u
SIGNAL PATH
16 VIDEO SIGNAL
CHROMA Y Y/CHROMA
REC
PB
RGB DRIVER
4-45 4-46 PK-50 (3/4)
MVC-FD85/FD90

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
PK-50 BOARD(4/4) (FD90 MODEL)

NO MARK:REC/PB MODE
R :REC MODE
-LCD type check-
TG(TG BLOCK) P :PB MODE 21 By measurimg the resistor valve between
A Pin 13 of CN803(FC-72 board) and Pin 4

-REF.NO.:5000 SERIES- IC902 of CN803(FC-72 board),the type of LCD can
XX MARK:NO MOUNT Q901-904
COM AMP BOOST BUFFER be discrimimated.
VG
VB
VR
* R901 Type CA :
5 TO(3/4) P_4.9V Type SH : 4.7k
L901
10uH
2520
PANEL_13.2V
PANEL_-15.3V
* R944
B L902
10uH R912 IC902
R936
100k 13.2 ± 0.5%
2.2
2520 680k C911 NJM062V(TE2)
R916 C909 560p
10k 0.1u CH Q903
1.6 13.2 2.2 2SD2216J-QR(K8).SO * C914
8
OUT1 VCC+ 16V C917
R932 TA A * R945 * C915 * C919
1.7
1.7
2SB1462J-QR(K8).SO
L903 C907 0.1u
0.001u R919 1.5 1.7 100k ± 0.5% F
10uH OUT2 F
19 TO(1/4)
7
B 1M
1T369-01-T8A
2520 * R903 IN1-
Q902
PANEL_4.9V 1.5 -10.6
2SB1462J-QR(K8).SO
C916
2SD2216J-QR(K8).SO
IN2-
D902
6
IN1+ * R946 2.2u C918
0.4 13.2 ± 0.5% 2012 2.2u
* R966
* R967
* R968
* R969
* R970
* R971
* R972
* R973
* R974
* R975
* R976
R921 -10.6
1.7
IN2+ F 2012
Q904
REG_GND 68k VCC- F * R952
1.7
R941
Q901
L905
C * L904 R909
XX 1.1 100k
* R947
± 0.5%
* R953
2520 XX R922 * R954
R929 C913
PANEL_3.2V 68k
1.1
4700 1u D903
C902 2012 MA8047-H-TX
* R917 B
* C901 3.3u -10.6
6.3V 20V C905 R933 R935 R942
TA A TA A 0.1u C908 R920 33k 100k 33k
F 82p R923 R928 * R950
R911 C906 22k 47k 4700
120k CH * R956
0.1u
PANEL_COM
D
COM-O
V-COM
VCO
C910
XX
CN901 24P
TG_24 * R957
1 VSH CLD
C904 TG_23 * R958
* R918 2 VDD SPD
0.1u F ± 5% TG_22 * R959
12 TO(1/4,3/4) D_3.2V 3 VR CTR
R904 TG_21 * R960
47k 4 VB EX3
* R961
3.1
3.0
3.1
1.5
3.1
3.1
3.1
1.5
1.5
TG_20
PANEL_COM 5 VG EX2 LCD901
E 13 TO(1/4) PANEL_COM
36 35 34 33 32 31 30 29 28 27 26 25 6 VSS VB12
PANEL
LCD
TG_18
VB
18 7 MODE1 RES
P16
VSEPC
P15
MUT
* R939
PDP
GND
VDD
TST2
TST1
OSCI
OSCO
TESTO
VB * R962
VG 8 MCLK TST
VG TG_12
VR 9 HCNT VR
VR R905
10 CLR VG
V-COM 47k 2.7 TG_24 * R951
19 20
48 47 46 45 44 43 42 41 40 39 38 37
13 14 15 16 17 18 19 20 21 22 23 24
V-COM SYNI CLD 11 OE VB
COM-O 1.4 TG_23 * R949
COM-O SYNC SPD 12 SRTL GND
VCO R910 XX 3.1 2.6 TG_22 * R948
VCO WIDE CTR 13 SRTR VSH
F NTSC NTSC 3.1
PDPC
IC901 EX3
0
0
TG_21
TG_20
14 VBC COM
NTSC
NTPC1 EX2 15 VCOM VGL
COMTST 0.3 TIMING 0 * R963
7 TO(3/4) COMTST TESTI GENERETOR TESTO 16 MODE2 VSS
3.1 3.1 TG_18 TG_17
TEST * IC901 RES 17 RESET MO2
V_REV 3.1 0 TG_17
V_REV TG_16
V_REV VREVC MODE2 18 GSRT MO1
H_REV * R913 3.1 0 TG_16 TG_15
H_REV TESTI MODE1 19 GPCK EX1
H_REV 0 TG_15
* C903 3.1 TG_14
HREVC EX1 20 GRES SPS
FRPV COMTST 0 0.1 TG_14 * R964
TG_13
FRPV COMTST SPS 21 VREFL CLS
D901
G * R902
XX 3.1
LOWI CLS
2.8
0
TG_13
22 VGL VCC
FRPT 23 VREFH VSH

FRPT TG_12
24 VGH VGH
WIDOV
WIDOT
*R908 R940
*
BGPO
SYNO
BLKO
FRPV
FRPT
BLKI
GND
HSY
VSY
VIN
TYPE CA TYPE SH
HDO
16 TO(1/4) 1 2 3 4 5 6 7 8 9 10 11 12
PANEL_V
1.5
1.6
2.9
2.8
1.5
1.5
H Ref TYPE SH TYPE CA Ref
R901
TYPE SH
XX
TYPE CA
0
Ref
R953
TYPE SH
XX
TYPE CA
0
P_XHD 10u
6 TO(3/4) C901 XX 6.3V R902
W_MSK XX 0 R954 0 XX
0.1u 0.22u R903 0 XX R956 0 XX
± 0.5%
* R927
* R934 C903
* R925
± 0.5%
0 10V 10V
B B R908 XX 0 R957 0 XX
6.8u R913 100k 82k R958 0 XX

C914 16V XX
C912 R917 1M XX R959 0 XX
82p R930 * R931
R977 0
CH 0.01u R918 0 0 R960 0 XX
XX C915 25V XX
I 11 TO(1/4)
MAKER_RECOG B
0.1u
R925
R927
68k
33k
47k
39k
R961
R962
0
XX
XX
0
FRPV
FRPT
C919 XX 25V
HSY B R931 XX 0 R963 XX 0
R934 0 XX R964 0 XX
IC901 LZ9GH234 CM7018L3-T
R939 XX 0 R966 XX 100k
10uH R940 XX 0 R967 XX 0

L904 XX +10%
R944 33k XX R968 0 XX
R945 22k 0 R969 0 XX
J SIGNAL PATH
R946
R947
33k
22k
XX
XX
R970
R971
XX
47
0
XX
R948 XX 0 R972 47 XX
VIDEO SIGNAL
16 R949 XX 0 R973 47 XX
CHROMA Y Y/CHROMA R950 XX 0 R974 XX 47
R951 XX 0 R975 XX 47
REC
R952 0 XX R976 XX 47
PB
TG
PK-50 (4/4) 4-47 4-48
MVC-FD85/FD90

1 2 3 4 5 6 7 8 9 10 11 12
FU-140 BOARD (FD90 MODEL) CONTROL SWITCH BLOCK

FU-146 BOARD (FD85 MODEL) (ZM330)
A CN005 6P S001
DC IN 1 XRS_ON1 XRS_ON1 1
1 2
(1st)
-REF.NO.:4000 SERIES- 2 XRS_ON2 XRS_ON2 2
3 (2nd) 4
XX MARK:NO MOUNT 3 UNREG_GND UNREG_GND 3
NO MARK:REC/PB MODE 4 D_3.2V D_3.2V 4

R022
R :REC MODE 0 5 ZOOM_SW_AD ZOOM_SW_AD 5
P :PB MODE 6 UNREG_GND UNREG_GND 6
RV001
10k
B ZOOM FREEZE (1st)
W T SHUTTER (2nd)
R023
0
C002
XX 9 BATT_SIG
B CONTROL SWITCH BLOCK(ZM330) is replaced as a block.
8 BATT/XEXT so that this PRINTED WIRING is omitted.
CN001 3P LF001
7 FAST_CHARGE_ON
J902 ACV_UNREG 1
R020 6 INIT_CHARGE_ON TO
C DC IN ACV_GND
BATT/XEXT
2
3
10
1/8W R004
1k
5 DC_PACK_SW
FC-72 BOARD
CN002
7.2
C003 R001 (THROUGH THE FU-52 HARNESS)
FB001 XX 4 D_3.2V
1k
B 7.2 3 ZOOM_SW_AD
(SEE PAGE 4-25)
Q001
R009 2 XRS_ON2
R008 TPC8305(TE12L) Q002
LND001 XX 0
0 2SB1122-ST-TD
6.8 2G 1 XRS_ON1
STATIC_GND
7.2
R002 S R005 R019 CN003 9P
D003 470k 1 6800 47k
LND002 7 D002
MA4Z082WA-(TX).SO 8D 1SS357-TPH3
STATIC_GND CN004 12P
7.0
5
6D
D D006
XX
3
S
7.2 1 REG_GND
0
0 2 REG_GND
4
G 3 REG_GND
Q003
CN002 4P D004 D001 6.8 4 REG_GND
UN9213J-(K8).SO F004 1.4A/32V
XX MA8120-TX
BATT_UNREG 1 5 BATT_UNREG TO
C001 FC-72 BOARD
BATT_SIG 2 0.022u 1.4A/32V 6 UNREG4 (BL/STP) CN001
FB002 F003
J901
BATTERY S BATT_GND 3
FB003
B
7 UNREG4 (THROUGH THE FU-51 HARNESS)
TERMINAL DC_PACK_SW 4 8 UNREG3(TRANS 4.9V)

F002 1.4A/32V (SEE PAGE 4-25)
R021
E 6.8
0
R006
1M
0
9
10
UNREG3
UNREG2 (FDD_P_5V)
F001 1.4A/32V
11 UNREG2 (FLASH)
16 FD85 MODEL:MVC-FD85 2.9
FD90 MODEL:MVC-FD90 Q004 12 UNREG1(3.2/1.8/HI)
SSM3K03FE(TPL3)
F005 1.4A/32V
Q005
SSM3K03FE(TPL3)
Note : Note :
DC IN
4-49 4-50 FU-140/146
MVC-FD85/FD90
FU-140 (DC IN)(FD90 MODEL) PRINTED WIRING BOARD

— Ref. No. FU-140 Board; 4,000 Series —

in the diagram.
FU-146 (MVC-FD85)
Transistor Diode
C 65 4 45 6 3
B E 12 3 32 1 2 1
There are few cases that the part printed on this FLASH UNIT
DC IN
FU-140 (FD90 MODEL) 4-51 4-52
MVC-FD85/FD90
FU-146 (DC IN)(FD85 MODEL) PRINTED WIRING BOARD

— Ref. No. FU-146 Board; 4,000 Series —

in the diagram.
FU-146 (MVC-FD85)
Transistor Diode
C 65 4 45 6 3
B E 12 3 32 1 2 1
There are few cases that the part printed on this FLASH UNIT
DC IN
4-53 4-54 FU-146 (FD85 MODEL)
MVC-FD85/FD90
4-3. WAVEFORM
CD-246 BOARD CD-248 BOARD PK-50/52 BOARD
(MVC-FD90 model) (MVC-FD85 model) (MVC-FD90/FD85 model)
REC/PB REC/PB REC/PB
1 IC101 1,3 1 IC201 1,3 1 IC901 8 9 IC904 wk qj IC802 wf
6.5µsec 6.5µsec
8.7Vp-p 8.7Vp-p
127µsec 127µsec 3.8Vp-p
440mVp-p 4.4Vp-p
H 85nsec 2H
2 IC101 2 2 IC201 2 2 IC901 9 q; IC904 wa,ws qk IC901 ej
3.8Vp-p 3.0Vp-p
24.0Vp-p 24.0Vp-p H
33.3msec 40msec 512nsec
400mVp-p
H
3 IC101 4,6 3 IC201 4,6 3 IC901 q; qa IC904 qh,qj ql IC901 ef
8.8Vp-p 8.8Vp-p 3.4Vp-p 3.4Vp-p

6.5µsec 127µsec 6.5µsec 127µsec 220mVp-p 127µsec V
H
4 IC101 5 4 IC201 5 4 IC901 w; qs IC802 8 w; IC901 wh
24.0Vp-p 24.0Vp-p 450mVp-p

33.3msec 40msec H 3.4Vp-p
86nsec
2H 11.5Vp-p
5 IC101 8 5 IC201 8 5 IC901 ws qd IC802 9 wa IC902 7
1.0Vp-p 1.3Vp-p
127µsec 127µsec 6.7Vp-p
400mVp-p 127µsec
11.5Vp-p H
2H
6 IC101 qf 6 IC201 qf 6 IC901 wf qf IC802 q;
3.7Vp-p 3.3Vp-p 200mVp-p

81.5nsec 81.5nsec H
2H 11.5Vp-p
7 IC101 qg,qh 7 IC201 qg,qh 7 IC904 ej qg IC802 w;
3.0Vp-p
3.6Vp-p 3.3Vp-p H
81.5nsec 81.5nsec
4.4Vp-p
2H
8 IC904 ef qh IC802 ws
3.4Vp-p
V
4.4Vp-p
2H
WAVEFORM
CD-246/248,PK-50/52 4-55 4-56
Waveforms and parts location of the FC- 4-4. PARTS LOCATION
72 board are not shown.
Pages from 4-57 to 4-58 are not shown. CD-246 BOARD (SIDE A)
D101 A-1
IC101 B-2
R111 A-1
R112 A-2
CD-246 BOARD (SIDE B)

C101 B-5
C102 B-4
C103 B-4
C104 A-5
C105 A-4
C106 B-4
C107 B-5
C108 B-5
C109 B-5
C110 B-5
C111 A-5
CN101 A-5
L101 A-5
Q101 A-4
Q102 B-5
R101 A-5
R102 A-5
R103 A-4
R104 A-4
R105 A-4
R106 A-4
R107 A-5
R108 B-5
R109 B-5
R110 A-5
CD-248 BOARD (SIDE A)

D201 A-2
IC201 B-2
R211 A-2
R212 A-2
CD-248 BOARD (SIDE B)

C201 B-5
C202 B-4
C203 A-4
C204 B-4
C205 A-4
C206 A-4
C207 B-5
C208 A-5
C209 B-5
C210 B-5
C211 B-4
CN201 A-4
L201 A-5
Q201 A-4
Q202 B-5
R201 A-3
R202 A-5
R203 A-4
R204 A-4
R205 A-4
R206 B-4
R207 B-4
R208 B-5
R209 B-5
R210 B-4
PARTS LOCATION
4-59 CD-246/248
PK-50 BOARD (SIDE A) PK-50 BOARD (SIDE B) PK-52 BOARD (SIDE A) PK-52 BOARD (SIDE B)
BT701 G-2 R817 B-5 C709 A-9 R703 B-14 BT701 G-2 R728 A-7 C705 B-14 R729 A-9
R818 B-4 C711 C-14 R704 C-15 R782 B-3 C709 A-9 R787 A-14
C701 A-8 R851 F-3 C783 A-14 R705 B-14 C701 A-8 R851 F-3 C711 C-14 R853 F-12
C702 A-8 R852 G-3 C801 B-13 R709 A-9 C702 A-8 R852 G-3 C783 A-14 R854 F-12
C703 A-7 R856 G-5 C802 B-14 R711 A-9 C703 A-7 R856 G-5 C851 G-12 R855 G-12
C704 A-7 R857 G-5 C803 B-11 R712 A-9 C704 A-7 R857 G-5 C852 G-12 R859 G-12
C706 B-3 R858 G-5 C804 B-11 R714 C-14 C706 B-3 R858 G-5 C854 F-12 R860 G-12
C707 A-6 R861 F-5 C805 A-11 R715 B-14 C707 A-6 R861 F-5 C855 F-12 R864 E-12
C708 A-6 R862 F-5 C806 B-12 R729 A-9 C708 A-6 R862 F-5 C857 G-12 R869 E-12
C710 C-3 R863 F-5 C807 C-12 R787 A-14 C710 C-3 R863 F-5 C858 G-12 R870 E-12
C781 A-3 R865 F-5 C808 B-12 R803 B-12 C781 B-3 R865 F-5 C860 G-12 R872 E-12
C782 A-3 R866 F-5 C809 B-11 R805 B-12 C782 A-3 R866 F-5 C861 G-13 R876 E-12
C853 G-5 R867 G-4 C810 B-11 R806 B-12 C853 G-5 R867 G-4 C863 E-12 R902 B-12
C856 G-5 R868 G-4 C811 B-13 R807 B-12 C856 G-5 R868 G-4 C866 D-13 R905 B-12
C859 G-5 R871 E-5 C812 A-13 R819 B-11 C859 G-5 R871 E-5 C901 A-9 R906 B-12
C862 G-4 R873 E-5 C813 A-12 R820 A-12 C862 G-4 R873 E-5 C902 B-9 R907 B-12
C864 G-4 R909 C-5 C814 A-12 R821 B-11 C864 G-4 R901 B-8 C903 B-12 R908 B-12
C865 E-5 R911 D-5 C815 A-12 R853 F-12 C865 E-5 R903 B-8 C904 B-12 R909 B-11
C906 C-5 R912 D-5 C816 A-12 R854 F-12 C906 B-7 R904 B-8 C905 C-12 R910 A-13
C907 C-5 R916 D-5 C851 G-12 R855 G-12 C915 C-7 R912 B-7 C907 B-9 R911 B-12
C909 D-5 R919 D-5 C852 G-12 R859 G-12 C916 B-7 R913 B-4 C908 B-11 R914 A-13
C911 D-5 R920 D-5 C854 F-12 R860 G-12 C922 C-5 R916 B-4 C909 B-11 R915 A-13
C914 B-8 R921 C-5 C855 F-12 R864 E-12 C923 D-5 R920 A-4 C910 A-11 R917 B-13
C916 C-8 R922 D-5 C857 G-12 R869 E-12 C924 D-5 R921 A-4 C911 B-11 R918 B-11
C918 C-8 R923 D-5 C858 G-12 R870 E-12 C925 C-4 R923 A-4 C912 A-12 R919 B-11
R928 C-5 C860 G-12 R872 E-12 C926 D-5 R924 A-4 C913 A-12 R925 B-11
D701 B-3 R929 C-5 C861 G-13 R901 B-11 C929 C-8 R931 B-5 C914 A-12 R926 B-11
D702 C-6 R932 D-5 C863 E-12 R902 D-12 R932 B-5 C917 B-11 R927 A-13
D703 C-6 R933 D-5 C866 D-13 R903 C-13 D701 B-3 R933 B-5 C918 D-12 R928 A-13
D784 B-2 R939 C-5 C901 C-13 R904 C-12 D702 C-6 R934 B-7 C919 D-12 R929 A-12
D786 A-3 R941 D-5 C902 A-9 R905 C-12 D703 C-6 R935 B-7 C920 D-13 R930 C-13
D787 A-3 R942 D-5 C903 D-12 R908 C-12 D786 A-3 R936 C-6 C921 D-12 R937 C-12
D851 F-3 R946 B-8 C904 C-12 R910 C-12 D787 A-3 R938 C-6 C927 C-12 R940 B-10
D853 E-5 R947 C-8 C905 B-9 R913 D-12 D851 F-3 R939 C-7 C928 C-11 R941 C-13
D902 C-5 R950 C-7 C908 C-12 R917 C-12 D853 E-5 R945 D-5 C931 B-10 R942 C-13
D903 C-8 R952 C-8 C910 C-12 R918 C-12 D902 B-8 R946 D-5 C932 B-14 R943 C-13
R953 C-8 C912 D-12 R925 D-12 D904 D-5 R947 D-5 R944 D-12
FB782 B-3 R954 C-8 C913 D-12 R927 D-12 R948 D-5 CN701 A-10 R952 C-13
FB783 B-2 R956 C-7 C915 B-10 R930 D-12 FB781 C-2 R949 D-5 CN702 B-9 R954 C-13
FB784 B-3 R963 C-8 C917 B-9 R931 D-12 FB782 B-2 R950 D-5 CN851 D-14 R955 C-12
FB785 B-3 R974 C-7 C919 B-11 R934 D-12 FB783 B-2 R951 D-5 CN901 C-10 R958 C-12
FB786 B-2 R975 C-7 R935 D-12 FB784 B-2 R953 C-5 R959 C-12
FB788 A-3 R976 B-6 CN701 A-10 R936 D-12 FB785 B-2 R956 C-5 D782 B-14 R960 C-12
FB789 A-3 CN702 B-9 R940 D-12 FB786 B-2 R957 C-5 D783 B-14 R961 C-11
FB790 B-3 S701 B-8 CN851 D-13 R944 B-9 FB788 B-3 R964 D-5 D784 C-15 R962 C-11
FB791 A-3 S702 B-6 CN901 C-10 R945 B-9 FB789 A-3 R965 D-5 D785 A-14 R963 C-11
S703 C-6 R948 B-10 FB790 B-3 R966 C-5 D788 A-14 R968 C-11
IC701 A-7 S704 F-2 D782 B-14 R949 B-10 FB791 A-3 R967 D-6 D789 B-14 R969 C-11
IC702 B-3 S705 B-3 D783 B-14 R951 B-10 R979 C-7 D790 B-14 R970 D-11
IC852 E-5 S706 F-2 D785 A-14 R957 C-11 IC701 A-7 R980 C-7 D852 E-12 R971 D-11
IC902 D-5 S707 B-5 D788 A-14 R958 C-11 IC702 B-3 R982 D-5 D901 A-10 R972 D-12
S708 C-3 D789 B-14 R959 C-11 IC852 E-5 R983 B-4 D903 D-13 R973 D-12
L701 A-7 S709 F-2 D790 B-14 R960 C-11 IC903 D-5 D906 B-10 R974 B-10
S710 C-5 D852 E-12 R961 C-11 S701 A-7 R975 D-12
Q851 E-5 S711 B-4 D901 D-12 R962 C-11 L701 A-7 S702 B-6 FB787 A-14 R976 D-12
Q852 E-5 R964 C-9 S703 B-6 FB901 A-11 R977 D-12
Q854 G-5 FB781 C-15 R966 B-9 Q851 E-5 S704 F-2 FB902 B-11 R981 B-10
Q855 F-5 FB787 A-14 R967 B-9 Q852 E-5 S706 F-2 FB903 A-11 R984 B-13
Q856 G-4 FB801 A-11 R968 B-10 Q854 G-5 S707 B-5 R985 B-13
Q857 F-5 FB802 B-11 R969 B-9 Q855 F-5 S708 C-3 IC851 F-12 R986 B-11
Q858 F-5 FB803 A-11 R970 C-11 Q856 G-4 S709 F-2 IC901 B-12 R987 A-13
Q859 F-5 R971 B-10 Q857 F-5 S710 C-5 IC902 B-13
Q860 G-4 IC801 B-13 R972 B-10 Q858 F-5 S711 B-4 IC904 C-12 SE701 C-15
Q861 F-5 IC802 B-12 R973 B-10 Q859 F-5
IC803 B-12 R977 B-11 Q860 G-4 J781 A-15 T851 F-13
R702 A-6 IC851 F-12 Q861 F-5 J782 B-15
R706 A-6 IC901 C-12 SE701 C-15 Q901 C-8
R707 A-6 Q902 B-7 L702 B-14
R710 C-6 J781 A-15 T851 F-13 Q905 C-7 L851 G-12
R713 C-6 J782 B-15 Q906 C-6 L852 G-12
R716 B-6 Q907 D-5 L853 G-13
R717 B-6 L702 B-14 L901 A-10
R718 B-6 L801 A-13 R702 A-6 L902 B-9
R719 B-6 L802 A-13 R706 A-6 L903 D-12
R720 B-6 L851 G-12 R707 A-6 L904 C-12
R721 B-5 L852 G-12 R710 C-6
R722 G-2 L853 G-13 R713 C-5 Q853 F-12
R723 B-5 L901 A-10 R716 B-6 Q903 C-13
R724 B-4 L902 A-10 R717 B-6 Q904 C-12
R725 B-5 L903 C-12 R718 B-6 Q908 D-12
R726 B-4 L904 C-13 R719 B-6
R727 A-7 L905 C-12 R720 B-6 R703 B-14
R728 A-7 R721 B-5 R704 C-15
R782 B-3 Q853 F-12 R722 G-2 R705 B-14
R808 A-5 Q901 D-12 R723 B-5 R709 A-9
R809 B-4 Q902 D-12 R724 B-4 R711 A-9
R812 B-4 Q903 D-12 R725 B-5 R712 A-9
R813 A-4 Q904 D-12 R726 B-3 R714 C-14
R814 B-4 R727 A-7 R715 C-14
PARTS LOCATION
PK-50/52 4-60
FU-140 BOARD (SIDE A) FU-146 BOARD (SIDE A)
D002 D-3 D002 D-3
D003 A-3 D003 A-3
D004 A-3 D004 A-3
D006 A-3 D006 A-3
FB002 A-2 FB002 A-2

FB003 A-2 FB003 A-2
Q002 D-3 Q002 D-3

Q003 C-3 Q003 C-3
Q005 C-3 Q005 C-3
R004 D-3 R004 D-3

R005 C-2 R005 C-2
R008 A-4 R008 A-4
R009 A-4 R009 A-4
R019 C-2 R019 C-2
R020 D-3 R020 D-3
R021 C-2 R021 C-2
FU-140 BOARD (SIDE B) FU-146 BOARD (SIDE B)

C001 A-6 C001 A-6
C002 A-6 C002 A-6
C003 A-6 C003 A-6
CN001 A-6 CN001 A-6

CN002 A-6 CN002 A-6
CN003 E-8 CN003 E-8
CN004 E-7 CN004 E-7
CN005 C-7 CN005 C-7
D001 B-6 D001 B-6
F001 E-6 F001 E-6

F002 E-7 F002 E-7
F003 E-7 F003 E-7
F004 E-7 F004 E-7
F005 E-6 F005 E-6
FB001 A-6 FB001 A-6
LF001 B-6 LF001 B-6
Q001 B-6 Q001 B-6

Q004 A-6 Q004 A-6
R001 A-6 R001 A-6

R002 A-6 R002 A-6
R006 C-6 R006 C-6
R022 B-7 R022 B-7
R023 C-7 R023 C-7
PARTS LOCATION
4-61E FU-140/146
MVC-FD85/FD90
SECTION 5
ADJUSTMENTS
1. Before Starting Adjustment
EVR Data Re-writing Procedure When Replacing Board

The data that is stored in the repair board, is not necessarily correct.
Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Procedure 2
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is
replaced.
(Machine before starting repair) PC PC (Machine after a board is replaced)
Save the EVR data Download the saved

to a personal computer. data to a machine.
Procedure 2
Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM to the
replaced board.
Remove the EEPROM and install it.
(Former board) (New board)
Procedure 3
When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or installed, save the
data from the same model of the same destination, and download it.
(Machine to be repaired) PC (Machine to be repaired)
Download the data.
Save the data.
(The same model of the same destination)
After the EVR data is saved and downloaded, check the

respective items of the EVR data.
(Refer to page 5-2 for the items to be checked.)
5-1
1-1. Adjusting Items When Replacing Main Parts and Boards
When replacing main parts and boards, adjust the items indicated by z in the following table.
Replaced parts
Block Mounted parts Board
replacement replacement replacement
IC901 (Timing generator)*1
IC904 (Timing generator)*2

CD-248/246 board IC201/101 (CCD imager)*5
IC802 (RGB decoder)*1
IC901 (RGB decoder)*2

IC301 (CAMERA DSP)
IC102 (S/H, AGC, A/D)
ND901 Back light unit
IC901 (VIDEO AMP)
(COMPLETE)*1
(COMPLETE)*2
IC406 EEPROM
IC508 EEPROM
IC801 (EVR)*1
IC902 (EVR)*2
(COMPLETE)
IC186 (EVR)
LCD901
Adjustment
Adjustment
Section
Zoom/Release unit
Flash unit *4
PK-50 board
PK-52 board
PK-50 board
PK-52 board
PK-50 board
PK-50 board
PK-52 board
PK-52 board
FC-72 board
FC-72 board
FC-72 board
FC-72 board
FC-72 board
FC-72 board
FC-72 board
FDD unit *3
Lens device
LCD block
LCD block
Initialization of B, Initialization of D page data r r

D, E, F, 7 page data Initialization of B, E, F, 7 page data r r
Video Video output level adj. r r r r r
Zoom key center adj. r r r
HALL adj. r r r r
Flange back adj. r r r r
F No. standard data input r r r r
Mechanical shutter adj. r r r r
Light level adj. and ND Shutter check r r r r r
Mixed color cancel adj. r r r r r
AWB standard data input r r r r r
Camera
White balance ND filter compensation *1 r r r r r
Auto white balance adj. r r r r r
Color reproduction adj. (ND filter OFF) r r r r r
Color reproduction adj. (ND filter ON)*1 r r r r r
Strobe white balance adj. r r r r r
CCD black defect compensation r r r
CCD white defect compensation r r r
LCD initial data input r r
VCO adj. r r r r r r r r
Black limit adj. *2 r r r r r
D range adj. *1 r r r r r
Bright adj. r r r r r r r r
LCD Contrast adj. r r r r r r r r
Color adj. r r r r r r r r
VG center adj, *2 r r r r r
V-COM level adj. *1 r r r r r
V-COM adj. r r r r r r r r r
White balance adj. r r r r r r r r r r
System control Battery end adj. r r
Alignment check (FDD unit) r r
Table. 5-1-1.
*1: MVC-FD90 model only. *2: MVC-FD85 model only.
*3: When replacing the FDD unit, reset the data of page: D, address: 6C to 6F to “00”. (Refer to “Record of Use check” of “5-2. SERVICE
MODE”)
*4: When replacing the Flash unit, reset the data of page: D, address: 67 to “00”. (Refer to “Emergency Memory Address of Flash Unit” of
“5-2. SERVICE MODE”)
*5: CD-248 board IC201: MVC-FD85, CD-246 baord IC101: MVC-FD90
5-2
5-1. ADJUSTMENT
1-1. PREPARATIONS BEFORE ADJUSTMENT
1-1-1. List of Service Tools

• Oscilloscope • Color monitor • Vectorscope • AC power adapter
• Regulated power supply • Digital voltmeter • Frequency counter
Ref. No. Name Parts Code Usage
Auto white balance adjustment/check
J-1 Filter for color temperature correction (C14) J-6080-058-A
White balance adjustment/check
J-2 Pattern box PTB-450 J-6082-200-A
J-3 Color chart for pattern box J-6020-250-A
J-4 Siemens star chart J-6080-875-A For checking the flange back
Adjustment remote commander
J-5 J-6082-053-B
(RM-95 upgraded).(Note 2)
J-6 Clear chart for pattern box J-6080-621-A
For connecting the measuring instruments and
J-7 CPC-12 jig (22P, 0.5mm) J-6082-436-A the adjustment remote commander
Alignment disk TFD2-1 (+) 8-967-990-01
J-8 For FDD dynamic inspection
(Two disks as pair) TFD2-2 (–) 8-967-990-11
Cleaning disk (OR-D29WA) 8-960-009-39
J-9 For FDD head cleaning (Note 1)
Cleaning disk Available on market
J-10 Personal computer with Windows95/98 installed For checking the recorded picture
J-11 Power code J-6082-223-A For the battery end adjustment
J-12 Mini pattern box J-6082-353-B For adjusting the flange back
J-13 Camera table J-6082-384-A For adjusting the flange back
Note 1: Usage and operating note Note 2: If the micro processor IC in the adjustment remote commander is
One or two seconds of momentary use of cleaning disk is sufficient not the new micro processor (UPD7503G-C56-12), The pages
such that FD is accessed momentarily by system control when cannot be switched. In this case, replace with the new micro
main power is turn on. After cleaning, insert a FD for playback. processor (8-759-148-35).
When cleaning is insufficient, use a cleaning disk again.
Caution: Avoid using a cleaning disk excessively. Head can be
broken.
J-1 J-2 J-3 J-4 J-5
J-6 J-7 J-8 J-9 J-10
J-11 J-12 J-13
Fig. 5-1-1.
5-3
1-1-2. Preparations
Note 1: For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.
Note 2: When performing only the adjustments, the lens block and boards Pattern box
need not be disassembled.
1) Connect the equipment for adjustments according to Fig. 5-1-

5.
2) Connect the adjustment remote commander to the following
connector or jack. About 90 cm
• CN803 of FC-72 board via CPC-12 jig (J-6082-436-A)
• LANC jack (MVC-FD90 model only)
Note 3: As disconnecting the FC-72 board CN801 means disconnecting

the lithium 3V power supply (PK-52/50 board BT701), data such
as date, time will be lost. After completing adjustments, preset
these data.
Note 4: Setting the “Forced Power ON Mode (Forced STILL Mode)”

1) Select page: 0, address: 01, and set data: 01. Front of the Protection glass
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the power (STILL mode) to be
turned on with PK-52/50 board removed. After completing
adjustments, be sure to exit the “Forced Power ON Mode”.
Note 5: Setting the “Forced Power ON Mode (Forced PLAY Mode)”

1) Select page: 0, address: 01, and set data: 01. Fig. 5-1-2.
The above procedure will enable the power (PLAY mode) to be
turned on. After completing adjustments, be sure to exit the “Forced
Power ON Mode”.
Note 6: Setting the “Forced Power ON Mode (Forced MOVIE Mode)”

1) Select page: 0, address: 01, and set data: 01.
The above procedure will enable the power (MOVIE mode) to be
turned on. After completing adjustments, be sure to exit the “Forced CPC lid
Power ON Mode”.
Note 7: Exiting the “Forced Power ON Mode”

Screw driver (–)
CPC-12 jig
22 pin flexible board
FC-72 board
CN803
Insulator side
Fig. 5-1-3.
5-4
1-1-3. Discharging of the Flashlight Power Supply
The capacitor which is used as power supply of flashlight is charged
with 200 V to 300 V voltage. Discharge this voltage before starting
adjustments in order to protect service engineers from electric shock
during adjustment.
Discharge procedure
1. Press the FLASH button (PK-52/50 board S705) and turn off
the FLASH LED (PK-52/50 board D701).
2. Fabricate the discharging jig as shown in Fig. 5-1-4 locally by
yourself. Connect the discharging jig to the positive (+) and
negative (–) terminal of the flash voltage charge capacitor. Allow
ten seconds to discharge the voltage.
Short jig
Capacitor
Fig. 5-1-4.
5-5
AC power adaptor
CN101: MVC-FD90 model CD-248 board : MVC-FD85 model Adjustment remote

CN201: MVC-FD85 model CD-246 board : MVC-FD90 model commander
CN001 CN002 FDD UNIT

CN251
CN301
CD-248/246
board CN701
CN101/CN201
CN702
FC-72 board CPC-12 jig
CN703 (J-6082-436-A)
CN101
DC-IN jack CN183/CN184 (Another side)
CN803
CN401 CN801
CN183: MVC-FD85
MVC-FD90 model only CN184: MVC-FD90
LANC
jack
AUDIO
(black) Color monitor Vector scope
VIDEO
(yellow) Terminated
at 75 Ω
AUDIO/VIDEO OUT jack

MVC-FD90
model only CN701
J781
PK-52/50 board
J782 CN702
LANC jack
CN901
PK-52 board : MVC-FD85 model

PK-50 board : MVC-FD90 model Note 1: Inchanging data, wait for more than 5 seconds after the
set was turned on, then change the data.
Note 2: Connect the GND terminal to floppy disk drive unit frame
when check the RF signal waveform.
Fig. 5-1-5.
5-6
1-1-5. Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments.
1. DEMO MODE (SETUP menu) ....................................... OFF 7. PROGRAM AE (PK-52/50 board) .............................. AUTO
2. DIGITAL ZOOM (CAMERA menu) .............................. OFF (No mark indicated on LCD)
3. WHITE BALANCE (CAMERA menu) ...................... AUTO 8. MACRO (PK-50 board) (MVC-FD90) ............................ OFF
4. FLASH LEVEL (CAMERA menu) ....................... NORMAL 9. FOCUS (MF unit) (MVC-FD90) .......................... MANUAL
5. EXPOSURE (CAMERA menu) ...................................... 0EV (PK-52 board) (MVC-FD85) ......................... AUTO
6. P. EFFECT (EFFECT menu) ........................................... OFF (No mark indicated on LCD)
10. DISPLAY (PK-52/50 board) ............................................ OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Color bar chart (Color reproduction adjustment frame) Electronic beam scanning frame
H
Yellow
Magenta
White
Cyan
Green
C C=D D
Red
Blue
Magenta
Yellow
Green
White
Cyan
Blue
Red
CRT picture frame
V
A B A=B B A
Fig. b (monitor TV picture)
Fig. a Enlargement
Video terminal
output waveform
Difference in level
Adjust the camera zoom and direction to

B A obtain the output waveform shown in Fig. a
and the monitor TV display shown in Fig. b.
Fig. 5-1-6.
3. Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust White
the picture frame as shown in Fig. 5-1-6. (Standard picture
841mm
frame)
2) Clear chart (Color reproduction adjustment frame) Black
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
1189mm
3) Flange back adjustment chart
Make the chart shown in Fig. 5-1-7 using A0 size (1189 mm ×
Fig. 5-1-7.
841 mm) black and white vellum paper.
Note: Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
5-7
1-2. INITIALIZATION OF B, D, E, F, 7 PAGE DATA
1-2-1. INITIALIZATION OF D PAGE DATA

1. Initializing the D Page Data 3. D Page Table
Note: If the D page data has been initialized, the following adjustments Note:
need to be performed again. Fixed data-1: Initialized data. ( Refer to “1. Initializing the D Page Data”).
1) Modification of D page data Fixed data-2: Modified data. (Refer to “2. Modification of D Page Data”).
2) LCD system adjustments
3) Battery end adjustment
4) Zoom key center adjustment Address Initial value Remark
FD85 FD90
Adjusting page D 00 to 0F
Adjusting Address 10 to FF 10 00 00 Test mode
11 to 1D Fixed data-1 (Initialized data)
Initializing Method: 1E Fixed data-2 (Modified data. Copy
1) Select page: 0, address: 01, and set data: 01. the data built in the same model.)
2) Select page: 2, address: 03, and set the following data. 1F to 61 Fixed data-1 (Initialized data)
05: MVC-FD85
62 to 63 Fixed data-2 (Modified data. Copy
04: MVC-FD90
the data built in the same model.)
3) Select page: 2, address: 00, and set data: 2D.
4) Select page: 2, address: 01, set data: 2D, and press the PAUSE 64 to 66 Fixed data-1 (Initialized data)
button of the adjustment remote commander. 67 00 00 Flash unit emergency
5) Select page: 2, address: 02, and check that the data changes to 68 Fixed data-1 (Initialized data)
“01”. 69
6) Perform “Modification of D Page Data”. 6A
6B
2. Modification of D Page Data
If the D page data has been initialized, change the data of the “Fixed 6C 00 00 Recording counter
data-2” address shown in the following table by manual input. 6D 00 00
6E 00 00
Modifying Method: 6F 00 00 Recording counter/MC CAM (FC-72
1) Before changing the data, select page: 0, address: 01, and set board IC501) emergency
data: 01. 70 Fixed data-2 (Modified data. Copy
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model. 71 to 77 Fixed data-1 (Initialized data)
Note: If copy the data built in the different model, the camera may 78 to 7D Fixed data-2 (Modified data. Copy
not operate. the data built in the same model.)
3) When changing the data, press the PAUSE button of the
7E to 7F Fixed data-1 (Initialized data)
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory. 80 to 87 Fixed data-2 (Modified data. Copy
4) Check that the data of adjustment addresses is the initial value. the data built in the same model.)
If not, change the data to the initial value. 88 Fixed data-1 (Initialized data)
89 80 80 Zoom key center adj.
Processing after Completing Modification of D Page data 8A to 8B Fixed data-2 (Modified data. Copy
2) Select page: 2, address: 01, and set data: 29, and press the
PAUSE button of the adjustment remote commander. 8C to 8F Fixed data-1 (Initialized data)
90 80 90 Battery end adj.
91 88 98
92 AD A7
93 C2 BC
94 CD C7
95 Fixed data-1 (Initialized data)
96
97
98 Fixed data-2 (Modified data. Copy
99 the data built in the same model.)
9A
9B
9C
9D
9E
9F
A0
5-8
1-2-2. Initializing the B, E, F, 7 Page Data
Address Initial value Remark
1. Initializing the B, E, F, 7 Page Data
FD85 FD90 Note 1: If “Initializing the B, E, F, 7 Page Data” is performed, all data of
A1 Fixed data-2 (Modified data. Copy the B page, E page, F page and 7 page will be initialized. (It is
the data built in the same model.) impossible to initialize a single page.)
Note 2: If the B, E, F, 7 Page data has been initialized, “Modification of B,
A2 Fixed data-1 (Initialized data)
E, F, 7 Page Data” and following adjustments need to be performed
A3 again.
A4 1) Video system adjustments
2) Camera system adjustments
A5 Fixed data-2 (Modified data. Copy
A6 Fixed data-1 (Initialized data) Adjusting page F
A7 Adjusting Address 10 to FF
A8 Adjusting page 7
A9 Fixed data-2 (Modified data. Copy Adjusting Address 00 to FF
the data built in the same model.) Adjusting page E
AA to CF Fixed data-1 (Initialized data) Adjusting Address 00 to FF
D0 20 AA/B2 Bright adj. (LCD) Adjusting page B
(*3) *3: LCD TYPE SH/ LCD TYPE CA Adjusting Address 00 to FF
D1 60 66/60 Color adj. (LCD)
(*3) *3: LCD TYPE SH/ LCD TYPE CA
Initializing Method:
D2 A0/80 A8/A0 White balance adj. (LCD) 1) Select page: 0, address: 01, and set data: 01.
(*2) (*3) *2: LCD TYPE SA/ LCD TYPE ST 2) Select page: 6, address: 03, and set the following data.
D3 90/80 7A/6A *3: LCD TYPE SH/ LCD TYPE CA 05: MVC-FD85
(*2) (*3) 04: MVC-FD90
D4 D0 B8/C0 Contrast adj. (LCD) 3) Select page: 6, address: 00, and set data: 2D.
(*3) *3: LCD TYPE SH/ LCD TYPE CA 4) Select page: 6, address: 01, set data: 2D, and press the PAUSE
D5 90 B0/54 Black limit adj.(LCD)(FD85), button.
(*3) D range adj.(LCD)(FD90) 5) Select page: 6, address: 02, and check that the data changes to
*3: LCD TYPE SH/ LCD TYPE CA “01”.
D6 80 7C/8A VG center adj.(LCD)(FD85) 6) Perform “Modification of B, E, F, 7 Page Data”.
(*3) V-COM level adj.(LCD)(FD90)
*3: LCD TYPE SH/ LCD TYPE CA 2. Modification of B, E, F, 7 Page Data
If the B, E, F, 7 Page data has been initialized, change the data of
D7 70/80 6F VCO adj. (LCD)(NTSC)
the “Fixed data-2” address shown in the following tables by manual
(*2) *2: LCD TYPE SA/ LCD TYPE ST
input.
D8 A0/80 74/8A V-COM adj.(LCD)
(*2) (*3) *2: LCD TYPE SA/ LCD TYPE ST Modifying Method:
*3: LCD TYPE SH/ LCD TYPE CA 1) Before changing the data, select page: 0, address: 01, and set
D9 72 73/5F Fixed data (DC BL LEVEL (LCD)) data: 01.
(*3) *3: LCD TYPE SH/ LCD TYPE CA 2) New data for changing are not shown in the tables because
DA Fixed data-1 (Initialized data) they are different in destination. When changing the data, copy
the data built in the same model.
DB
Note: If copy the data built in the different model, the camera may
DC 9A B5/9A Fixed data (AC BL LEVEL (LCD)) not operate.
(*3) *3: LCD TYPE SH/ LCD TYPE CA 3) When changing the data, press the PAUSE button of the
DD 90/60 6F/4F VCO adj. (LCD)(PAL) adjustment remote commander each time when setting new
(*2) (*3) *2: LCD TYPE SA/ LCD TYPE ST data to write the data in the non-volatile memory.
*3: LCD TYPE SH/ LCD TYPE CA 4) Check that the data of adjustment addresses is the initial value.
DE Fixed data-2 (Modified data. Copy If not, change the data to the initial value.
Processing after Completing Modification of B, E, F, 7 Page data
DF to FF Fixed data-1 (Initialized data)
Table. 5-1-2. 2) Select page: 2, address: 01, and set data: 29, and press the
PAUSE button of the adjustment remote commander.
5-9
3. F Page table
Note:
Fixed data-1: Address Initial value Remark
Initialized data.(Refer to “1. Initializing the B, E, F, 7 Page Data”).
Fixed data-2: FD85 FD90
Modified data. (Refer to “2. Modification of B, E, F, 7 Page Data”). 41 03 03 Color reproduction adj.
42 E9 E9 (ND Filter OFF)
Address Initial value Remark 43 63 63
FD85 FD90 44 83 83
00 to 0F 45 D5 D5
10 Fixed data-1 (Initialized data) 46 FE FE
11 47 73 73
12 48 45 45
13 49 Fixed data-1 (Initialized data)
14 12 1C Flange back adj. 4A
15 A8 94 4B
16 18 26 4C
17 C5 EC 4D 28 28 Strobe white balance adj.
18 12 13 4E 78 78
19 C9 B9 4F *1 00 White balance ND filter
1A 00 00 50 *1 00 compensation (MVC-FD90)
1B 00 00 *1: Fixed data-1
1C 00 00 51 *1 03 Color reproduction adj.
1D 00 00 52 *1 E9 (ND Filter ON)(MVC-FD90)
1E 41 46 53 *1 63
1F 00 00 54 *1 83
20 20 20 55 *1 D5
21 20 20 56 *1 FE
22 20 20 57 *1 73
23 44 44 58 *1 45 *1: Fixed data-1
24 0A 0A 59 00 00 AWB standard data input
25 00 00 5A 14 14 Mechanical shutter adj.
26 85 85 Light level Adj. 5B Fixed data-1 (Initialized data)
27 Fixed data-1 (Initialized data) 5C 63 63 Color reproduction adj.
28 94 93 Light level Adj. 5D 83 83 (ND Filter OFF)
29 47 48 F No. standard data input 5E 03 03
2A 41 42 5F E9 E9
2B 3D 3E 60 *1 63 Color reproduction adj.
2C 3D 3D 61 *1 83 (ND Filter ON)(MVC-FD90)
2D Fixed data-1 (Initialized data) 62 *1 03
2E 80 82 Hall adj. 63 *1 E9 *1: Fixed data-1
2F 93 94 64 64 64 Strobe white balance adj.
30 Fixed data-1 (Initialized data) 65 61 61 Video output level adj.
31 66 61 61
32 67 Fixed data-1 (Initialized data)
33 68 Fixed data-2 (Modified data. Copy
34 15 15 Hall adj. the data built in the same model.)
35 7C 7C 69 00 00 Strobe white balance adj.
36 Fixed data-1 (Initialized data) 6A AD C0
37 6B 00 00
38 6C 0B 0B Mechanical shutter adj.
39 6D C2 C2
3A 2F 2F AWB standard data input 6E 09 09
3B 37 37 6F 42 42
3C 40 40 70 06 06
3D D0 D0 71 C2 C2
3E Fixed data-1 (Initialized data) 72 05 05
3F B5 B5 Auto white balance adj. 73 C2 C2
40 43 43 74 04 04
5-10
4. 7 Page Table
Note:
Fixed data-1:
FD85 FD90 Initialized data. (Refer to “1. Initializing the B, E, F, 7 Page Data”.)
75 C2 C2 Mechanical shutter adj. Fixed data-2:
Modified data. (Refer to “2. Modification of B, E, F, 7 Page Data”).
76 33 33
77 33 33
78 33 33
FD85 FD90
79 33 33
00 to 5F Fixed data-1 (Initialized data)
7A 33 33
60 0F 0F CCD black defect compensation
7B 33 33
61 FF FF
7C 33 33
62 0F 0F
7D 33 33
63 FF FF
7E 33 33
64 0F 0F
7F 33 33
65 FF FF
80 00 00 Auto white balance adj.
66 0F 0F
81 to 9F Fixed data-1 (Initialized data)
67 FF FF
A0 00 00 Mixed color cancel adj.
68 0F 0F
A1 00 00
69 FF FF
A2 00 00
6A 0F 0F
A3 00 00
6B FF FF
A4 to FF Fixed data-1 (Initialized data)
6C 0F 0F
Table. 5-1-3.
6D FF FF
6E 0F 0F
6F FF FF
70 0F 0F
71 FF FF
72 0F 0F
73 FF FF
74 0F 0F
75 FF FF
76 0F 0F
77 FF FF
78 0F 0F
79 FF FF
7A 0F 0F
7B FF FF
7C 0F 0F
7D FF FF
7E 0F 0F
7F FF FF
80 0F 0F
81 FF FF
82 0F 0F
83 FF FF
84 0F 0F
85 FF FF
86 0F 0F
87 FF FF
88 0F 0F CCD white defect compensation
89 FF FF
8A 0F 0F
8B FF FF
8C 0F 0F
8D FF FF
8E 0F 0F
8F FF FF
90 0F 0F
5-11
5. E Page Table
Note:
Fixed data-1:
NTSC PAL Initialized data. (Refer to “1. Initializing the B, E, F, 7 Page Data”.)
91 FF FF CCD white defect compensation Fixed data-2:
Modified data. (Refer to “2. Modification of B, E, F, 7 Page Data”).
92 0F 0F
93 FF FF
94 0F 0F Address Remark
95 FF FF
00 to FF Fixed data-1 (Initialized data)
96 0F 0F
97 FF FF Table. 5-1-5.
98 0F 0F
6. B Page Table
99 FF FF Note:
9A 0F 0F Fixed data-1:
9B FF FF Initialized data. (Refer to “1. Initializing the B, E, F, 7 Page Data”.)
Fixed data-2:
9C 0F 0F Modified data. (Refer to “2. Modification of B, E, F, 7 Page Data”).
9D FF FF
9E 0F 0F
9F FF FF Address Remark
A0 0F 0F 00 to 2F Fixed data-1 (Initialized data)
A1 FF FF 30 Fixed data-2 (Modified data. Copy the data built in
A2 0F 0F the same model.)
A3 FF FF 31 to 72 Fixed data-1 (Initialized data)
A4 0F 0F 73 Fixed data-2 (Modified data. Copy the data built in
A5 FF FF the same model.)
A6 0F 0F 74 to FF Fixed data-1 (Initialized data)
A7 FF FF
Table. 5-1-6.
A8 0F 0F
A9 FF FF
AA 0F 0F
AB FF FF
AC 0F 0F
AD FF FF
AE 0F 0F
AF FF FF
B0 to FF Fixed data-1 (Initialized data)
Table. 5-1-4.
5-12
1-3. VIDEO SYSTEM ADJUSTMENTS
1. Video Output Level Adjustment (FC-72 board)

Adjust the sync level and burst level of the composite video signal
output.
Mode PLAY
Signal Arbitrary
Measurement Point Video terminal of AV OUT jack
(75 Ω terminated)
Measuring Instrument Oscilloscope
Adjustment Page F
Adjustment Address 65, 66
Specified Value Sync level:
A=286 ± 5 mV (NTSC mode)
A=300 ± 5 mV (PAL mode)
Burst level:
B=286 ± 5 mV (NTSC mode)
B=300 ± 5 mV (PAL mode)
Menu setting:
1) VIDEO OUT of SET UP menu
............................ NTSC (NTSC mode)
............................ PAL (PAL mode)
Adjusting method:
2) Select page: 5, address: F1, and set data: 04.
3) Select page: F, address: 65, change the data and set the sync
level (A) to the specified value.
4) Press the PAUSE button of the adjustment remote commander.
5) Select page: F, address: 66, change the data and set the burst
level (B) to the specified value.
6) Press the PAUSE button.
H
Fig. 5-1-8.
5-13
1-4. CAMERA SYSTEM ADJUSTMENTS
Before perform the camera system adjustments, check that the

specified values of “VIDEO SYSTEM ADJUSTMENT” are
satisfied.
Data setting during camera system adjustments: 2. HALL Adjustment

Perform the following data setting before the camera system For detecting the position of the lens iris, adjust the hall AMP gain
adjustments. and offset.
1) Select page: 0, address: 01, and set data: 01. Mode STILL
2) After writing down the original data of the following addresses, Subject All black
input the following data. (Cover the lens with a black cap)
Page Address Data Remark Measurement Point Display data of page 1 (Note 1)
E 43 10 Measuring Instrument Adjustment remote commander
E 6C FF FD90 model only Adjustment Page F
E 8F 00 Adjustment Address 2E, 2F, 34, 35
B 67 00 Specified Value 13 to 17 during IRIS OPEN
B CC 04 FD90 model only 7B to 7F during IRIS CLOSE
Note: Press the PAUSE button of the adjustment remote commander
each time to set the data. Note 1: Displayed data of page 1 of the adjustment remote commander.
After completing the camera system adjustments, release the 1 : 00 : XX
data setting. Display data
Note 2: If the data of page: 6, address: 02 is “01”, select page: 6, address:
01, set data: 00, and press the PAUSE button.
2) Select the above addresses, and input the orignal data writen
down at step 2).
Adjusting method:
each time to set the data. 1) Select page: 0, address: 01, and set data: 01.
3) Select page: 0, address: 01, and set data: 00. 2) Select page: 6, address: 94, and set data: 15.
3) Select page: 6, address: 95, and set data: 7D.
4) Select page: 6, address: 01, set data: 6D, and press the PAUSE
1. Zoom Key Center Adjustment button of the adjustment remote commander. (The HALL
Set the A/D value center of the microprocessor to the center voltage adjustment is performed and the adjustment data is stored in
of the zoom key. page: F, address: 2E, 2F, 34 and 35.)
If deviated, the zoom lens operates of itself ,even if the zoom key is 5) Select page: 6, address: 02, and check that the data is “01”.
the center position. 6) Select page: 6, address: 01, set data: 00, and press the PAUSE
button.
Mode STILL
Subject Arbitrary Checking method:
Measurement Point Display data of page: 2, address: 5C 1) Select page: 0, address: 03, and set data: 03.
Measuring Instrument Adjusting remote commander 2) Select page: 6, address: 01, set data: 01, and press the PAUSE
button.
Adjustment Page D
3) Select page: 1, and check that the display data (Note1) during
Adjustment Address 89 IRIS OPEN satisfies the specified value.
4) Select page: 6, address: 01, set data: 03, and press the PAUSE
Note: Don’t touch the zoom lever during adjustment. button.
5) Select page: 1, and check that the display data during IRIS
Adjusting method: CLOSE satisfies the specified value.
2) Select page: 2, address: 5C, read the data, and this data is named Processing after Completing Adjustments:
D5C. 1) Select page: 6, address: 01, set data: 00, and press the PAUSE
3) Select page: D, address: 89, set the following data. button.
D5C (When 6C D5C 8A) 2) Select page: 6, address: 94, and set data: 00.
6C (When 5D D5C<6C) 3) Select page: 6, address: 95, and set data: 00.
8A (When 8A<D5C 99) 4) Select page: 0, address: 03, and set data: 00.
Note: When D5C<5D or 99<D5C, the zoom key is defective. 5) Select page: 0, address: 01, and set data: 00.
5-14
(Using Minipattern Box)
The inner focus lens flange back adjustment is carried out Adjusting method:
automatically. In whichever case, the focus will be deviated during 1) Install the minipattern box so that the distance between it and
auto focusing/manual focusing. the front of the lens of the camera is less than 3cm.
Mode STILL 2) Make the height of the minipattern box and the camera equal.
3) Check that the output voltage of the regulated power supply is
Subject Siemens star chart with ND filter for
the specified voltage.
the minipattern box (Note 1)
Measurement Point 5) Check that the center of the Siemens star chart and the center
Check operation on TV monitor
Measuring Instrument of the exposure screen coincide.
Adjustment Page F 6) Check that the data of page: F, address: 14 to 25 is the initial
value (See table below).
Adjustment Address 14 to 25
Address Data Address Data Address Data
Note 1: Dark Siemens star chart. 14 12/1C 1B 00 22 20
01, set data: 00, and press the PAUSE button. 15 A8/94 1C 00 23 44
16 18/26 1D 00 24 0A
Preparations before adjustments: 17 C5/EC 1E 41/46 25 00
The minipattern box is installed as shown in the following figure.
18 12/13 1F 00
Note: the attachment lenses are not used.
Specified voltage: The specified voltage varies according to the 19 C9/B9 20 20
minipattern box, so adjust the power supply 1A 00 21 20
output voltage to the specified voltage written
Note: MVC-FD85/MVC-FD90
on the sheet which is supplied with the
minipattern box.
Below 3 cm button of the adjustment remote commander.
Minipattern box button.
(The adjustment data will be automatically input to page: F,
Camera addresses: 14 to 25.)
9) Select page: 6, address: 02, and check that the data is changed
Camera to “01”.
table
Processing after Completing Adjustments:
Regulated power supply
Output voltage : Specified voltage ±0.01Vdc 1) Select page: 6, address: 01, set data: 00, and press the PAUSE
Output current : more than 3.5A button.
2) Perform “Flange Back Check”.
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –) Need not connected

Black (GND)
Fig. 5-1-9.
5-15
(Using Flange Back Adjustment Chart)
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
4-1. Flange Back Adjustment (1) 4-2. Flange Back Adjustment (2)
Mode STILL Perform this adjustment after performing “Flange Back Adjustment
(1)”.
Subject Flange back adjustment chart
(2.0 m from the front of the lens) Subject Subject more than 500m away
(Luminance: 350 ± 50 lux) (Subjects with clear contrast such as
buildings, etc.)
Measurement Point
Check operation on TV monitor Measurement Point
Measuring Instrument Check operation on TV monitor
Measuring Instrument
Adjustment Page F
Adjustment Page F
Note: If the data of page: 6, address: 02 is “01”, select page: 6, address:
01, set data: 00, and press the PAUSE button. Note: Make the lens horizontal and perform this adjustment.
Adjusting method: Adjusting method:

2) Check that the center of the chart for the flange back adjustment 2) Set the zoom lens to the TELE end and expose a subject that is
and the center of the exposure screen coincide. more than 500 m away (subject with clear contrast such as
3) Check that the data of page: F, address: 14 to 25 is the initial building, etc.). (Nearby subjects less than 500 m away should
value (See table below). not be in the screen.)
3) Select page: 6, address: 02, and check that the data is “00”.
Address Data Address Data Address Data 4) Select page: 6, address: 01, set data: 13, and press the PAUSE
14 12/1C 1B 00 22 20 button of the adjustment remote commander.
15 A8/94 1C 00 23 44 5) Place a ND filter on the lens so that the optimum image is
obtain.
16 18/26 1D 00 24 0A
17 C5/EC 1E 41/46 25 00 button.
18 12/13 1F 00 (The adjustment data will be automatically input to page: F,
19 C9/B9 20 20 addresses: 14 to 25.)
1A 00 21 20
Note: MVC-FD85/MVC-FD90 Processing after Completing Adjustments:
4) Select page: 6, address: 01, set data: 13, and press the PAUSE 1) Select page: 0, address: 01, and set data: 00.
button of the adjustment remote commander. 2) Turn off the power and turn on again.
5) Select page: 6, address: 01, set data: 15, and press the PAUSE 3) Perform “Flange Back Check”.
button.
(The adjustment data will be automatically input to page: F,
addresses: 14 to 25.)
6) Select page: 6, address: 02, and check that the data is changed
to “01”.

button.
2) Perform “Flange Back Adjustment (2)”.
5-16
5. Flange Back Check 7. Mechanical Shutter Adjustment
Mode STILL Adjust the period which the mechanical shutter is closed, and
compensate the exposure.
Subject Siemens star
(2.0 m from the front of the lens) Mode STILL
(Luminance : approx. 200 lux) Subject Clear chart
Measurement Point (Color reproduction adjustment
Check operation on TV monitor frame)
Adjustment Page F
Specified Value The lens is focused.
Adjustment Address 5A, 6C to 7F
Switch setting:
1) FOCUS .................................................... AUTO (MVC-FD90) Note: 1 If the data of page: 6, address: 02 is “01”, select page: 6, address:
.... AUTO (No mark indicated on LCD) (MVC-FD85)
Note: 2 Install the clear chart at a distance of about 10 cm from the front
of the lens. (It is recommended.)
Checking method:
1) Place the Siemens star 2.0m from the front of the lens. Adjusting method:
2) To open the IRIS, decrease the luminous intensity to the 1) Shoot the clear chart with the zoom WIDE end.
Siemens star up to a point before noise appear on the image. 2) Select page: 0, address: 01, and set data: 01.
3) Shoot the Siemens star with the zoom TELE end. 3) Select page: 6, address: 01, set data: AD, and press the PAUSE
4) Select page: 5, address: F1, and set data: FF. button of the adjustment remote commander.
5) Observe the TV monitor and check that the lens is focused. (The mechanical shutter adjustment is performed and the
6) Select page: 6, address: 2C, and set data: 01. adjustment data is stored in page: F, address: 5A, 6C to 7F.)
7) Shoot the Siemens star with the zoom WIDE end. 4) Select page: 6, address: 02, and check that the data changes to
8) Observe the TV monitor and check that the lens is focused. “01”.
Processing after Completing Adjustments: Processing after Completing Adjustments:

1) Select page: 6, address: 2C, and set data: 00. 1) Select page: 6, address: 01, set data: 00, and press the PAUSE
2) Select page: 5, address: F1, and set data: 00. button.
6. F No. Standard Data Input

Compensate the unevenness of the iris meter sensitivity.
Mode STILL
Subject Clear chart
(Color reproduction adjustment
frame)
Adjustment Page F
Adjustment Address 29 to 2C

Note 2: After the power is turned on, this adjustment can be done only
once.
Adjusting method:
1) Shoot the clear chart with the zoom WIDE end.
3) Select page: 6, address: 01, set data: BB, and press the PAUSE
(The F No. standard data input is performed and the adjustment
data is stored in page: F, address: 29 to 2C.)

button.
5-17
8. Picture Frame Setting
Mode STILL Check on an oscilloscope
Subject Color bar chart
1. Horizontal period
(Color reproduction adjustment A=B C=D
frame) About 90 cm from the front of
the lens B C
Measurement Point Video output terminal A D
Measuring Instrument Oscilloscope and TV monitor
Specified Value A=B, C=D, E=F
Note 1: Display data of page 1 of the adjustment remote commander.

1 : XX : XX
XL or YL data
XH or YH data
Setting method:
1) Select page: 5, address: F1, and set data: FF.
2) Adjust the zoom and the camera direction, and set the picture
frame to the specified position.
3) Mark the position of the picture frame on the monitor display,
and adjust the picture frame to this position in following
adjustments using “Color reproduction adjustment frame”. Fig. 5-1-10.
5) Select page: 1, and note down the XH data and XL data. (Note1) 2. Vertical period
6) Select page: 0, address: 03, and set data: 22. E E=F F
7) Select page: 1, and note down the YH data and YL data. (Note1)
How to reset the zoom and focus when they deviated:

If the zoom and focus deviated due to some reason, reset them in
the following method. V
Fig. 5-1-11.
1) Select page: 6, address: 90, and set data: XL. (Note 2)
2) Select page: 6, address: 91, and set data: XH. (Note 2) Check on the monitor TV (Underscanned mode)
3) Select page: 6, address: 92, and set data: YL. (Note 3)
4) Select page: 6, address: 93, and set data: YH. (Note 3)
button and wait for 1 second.
6) Select page: 6, address: 2C, and set data: 01.
button.
Note 2: The data noted down at step 5) .of the “Setting method”.
Note 3: The data noted down at step 7) .of the “Setting method”.
Color bar chart picture frame Monitor TV picture frame

Fig. 5-1-12.
5-18
9. Light Level Adjustment and ND Shutter Check 10. Mixed Color Cancel Adjustment
Adjust the standard LV value. Perform the mixed color cancel adjustment using the each data of
Mode STILL the color bars.
Subject Clear chart Mode STILL
(Color bar standard picture frame) Subject Color bar chart
Measurement Point Display data of page 1 (Note 2) (Color bar standard picture frame)
Measuring Instrument Adjustment remote commander Adjustment Page F
Adjustment Page F Adjustment Address A0 to A3
Adjustment Address 26, 28
Note 1: This adjustment should be carried out upon completion of “Light
Specified Value AE level 1: 0FE0 to 1020 Level Adjustment and ND Shutter Check”.
AE level 2: Bellow 1100 Note 2: If the data of page: 6, address: 02 is “01”, select page: 6, address:
(MVC-FD90) 01, set data: 00, and press the PAUSE button.
Note 1: If the data of page: 6, address: 02 is “01”, select page: 6, address: Adjusting method:
01, set data: 00, and press the PAUSE button. 1) Select page: 0, address: 01, and set data: 01.
Note 2: Displayed data of page 1 of the adjustment remote commander. 2) Check that the picture frame is set to the specified position.
1 : XX : XX (Refer to “8. Picture Frame Setting”.)
Display data 3) Select page: 6, address: 01, set data: D7, and press the PAUSE
Adjusting method: 4) Select page: 6, address: 01, set data: D5, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01. button.
2) Select page: 6, address: 01, set data: 0D, and press the PAUSE (The mixed color cancel adjustment is performed and the
button of the adjustment remote commander. adjustment data is stored in page: F, address: A0 to A3.)
(The light level adjustment is performed and the adjustment Note: Observe the TV monitor and check that a vertical line is
data is stored in page: F, address: 26, 28.) indicated inside each color zone.
3) Select page: 6, address: 02, and check that the data is “01”. 5) Select page: 6, address: 02, and check that the data is “01”.
• AE level 1 Check
4) Select page: 0, address: 03, and set data: 06. Processing after Completing Adjustments:
5) Select page: 1, and check that the display data (Note2) satisfies 1) Select page: 6, address: 01, and set data: 00, and press the
the AE level 1 specified value. PAUSE button.
• AE level 2 Check (MVC-FD90) 2) Select page: 0, address: 01, and set data: 00.
6) Select page: E, address: 41, set data: 6B, and press the PAUSE
button.
8) Select page: 1, and check that the display data (Note2) satisfies
the AE level 2 specified value.

1) Select page: E, address: 41, set data: 6A, and press the PAUSE
button.
button.
5-19
11. Auto White Balance Standard Data Input 12. White Balance ND Filter Compensation
Adjust the white balance standard data at 3200 K. (MVC-FD90)
Mode STILL Compensate the white balance deviation when ND filter is ON.
Subject Clear chart Mode STILL
(Color bar standard picture frame) Subject Clear chart
Adjustment Page F (Color bar standard picture frame)
Adjustment Address 3A to 3D, 59 Adjustment Page F
Adjustment Address 4F, 50
01, set data: 00, and press the PAUSE button. Note 1: This adjustment should be carried out upon completion of “Auto
Note 2: After the power is turned on, this adjustment can be done only White Balance Standard Data Input”.
once. Note 2: If the data of page: 6, address: 02 is “01”, select page: 6, address:
Adjusting method: Note 3: After the power is turned on, this adjustment can be done only
1) Select page: 0, address: 01, and set data: 01. once.
button of the adjustment remote commander. Adjusting method:
3) Select page: 6, address: 01, set data: 0B, and press the PAUSE 1) Select page: 0, address: 01, and set data: 01.
button. 2) Select page: F, address: 27, after noting down the data, set data:
(The auto white balance standard data input is performed and 80, and press the PAUSE button of the adjustment remote
the adjustment data is stored in page: F, address: 3A to 3D, 59) commander.
4) Select page: 6, address: 02, and check that the data is “01”. 3) Select page: 6, address: 1C, set data: 03, and wait for 1 second.
Processing after Completing Adjustments: button of the adjustment remote commander.
1) Select page: 6, address: 01, and set data: 00, and press the 5) Select page: 6, address: 01, set data: 09, and press the PAUSE
PAUSE button. button.
2) Select page: 0, address: 01, and set data: 00. (The white balance ND filter compensation is performed and
the adjustment data is stored in page: F, address: 4F, 50.)

1) Select page: 6, address: 1C, set data: 00.
PAUSE button.
3) Select page: F, address: 27, set the data noted down at step 2)
of “Adjusting method”, and press the PAUSE button.
5-20
13. Auto White Balance Adjustment 14. Color Reproduction Adjustment (ND Filter OFF)
Adjust to the proper auto white balance output data. Adjust the color Separation matrix coefficient so that proper color
If it is not correct, auto white balance and color reproducibility will reproduction is produced.
be poor. Mode STILL
Mode STILL Subject Color bar chart
Subject Clear chart (Color reproduction (Color bar standard picture frame)
adjustment frame) Adjustment Page F
Filter Filter C14 for color temperature Adjustment Address 41 to 48, 5C to 5F
correction
Measurement Point Display data of page 1 (Note 2) Note 1: This adjustment should be carried out upon completion of “Auto
Measuring Instrument Adjustment remote commander White Balance Standard Data Input” and “Auto White Balance
Adjustment”.
Adjustment Page F Note 2: If the data of page: 6, address: 02 is “01”, select page: 6, address:
Adjustment Address 3F, 40, 80 01, set data: 00, and press the PAUSE button.
Note 3: After the power is turned on, this adjustment can be done only
Specified Value R ratio: 29E0 to 2B20 (MVC-FD85)
once.
B ratio: 5F20 to 6060 (MVC-FD85)
R ratio: 2760 to 28A0 (MVC-FD90)
Adjusting method:
B ratio: 5E60 to 5FA0 (MVC-FD90)
2) Check that the picture frame is set to the specified position.
Note 1: This adjustment should be carried out upon completion of “Auto (Refer to “8. Picture Frame Setting”.)
White Balance Standard Data Input” and “White Balance ND Filter
3) Select page: B, address: 67, after noting down the data, set
compensation (MVC-FD90)”.
Note 2: If the data of page: 6, address: 02 is “01”, select page: 6, address: data: 00, and press the PAUSE button.
01, set data: 00, and press the PAUSE button. 4) Select page: 6, address: 01, set data: AB, and press the PAUSE
Note 3: After the power is turned on, this adjustment can be done only button.
once. 5) Select page: 6, address: 12, set data: 80, and wait for 1 seconds.
Note 4: Displayed data of page 1 of the adjustment remote commander. 6) Select page: 6, address: 12, set data: 00, and wait for 2 seconds.
1 : XX : XX 7) Select page: 6, address: 01, set data: A9, and press the PAUSE
Display data button.
(The color reproduction adjustment is performed and the
Adjusting method: adjustment data is stored in page: F, address: 41 to 48, 5C to
1) Place the C14 filter for color temperature correction on the 5F.)
lens. Note: Observe the TV monitor and check that a sign “ ” is indicated
2) Select page: 0, address: 01, and set data: 01. inside each color zone.
3) Select page: F, address: 49 to 4C, and note down the data of 8) Select page: 6, address: 02, and check that the data is “01”.
each address.
4) Input the following data to page: F, addresses: 49 to 4C. Processing after Completing Adjustments:
Address 49 4A 4B 4C button.
Data 2A 80 5F C0 MVC-FD85 2) Select page: B, address: 67, set the data noted down at step 3),
28 00 5F 00 MVC-FD90 and press the PAUSE button.
3) Select page: 0, address: 01, and set data: 00
each time to set the data.
5) Select page: 6, address: 01, set data: A7, and press the PAUSE
button.
6) Select page: 6, address: 01, set data: A5, and press the PAUSE
button. (The auto white balance adjustment is performed and
the adjustment data is stored in page: F, address: 3F, 40 and
80.)
8) Select page: 6, address: 01, set data: 3F, and press the PAUSE
button.
10) Select page: 1, and check that the display data (Note 4) satisfies
the R ratio specified value.
12) Select page: 1, and check that the display data (Note 4) satisfies
the B ratio specified value.
13) Select page: F, address: 49 to 4C, and input the data noted down
at step 3).

button.
5-21
15. Color Reproduction Adjustment (ND Filter ON)
(MVC-FD90)
Adjust the color Separation matrix coefficient so that proper color
reproduction is produced.
Mode STILL
(Color bar standard picture frame)
Adjustment Page F
Adjustment Address 51 to 58, 60 to 63
Note 1: This adjustment should be carried out upon completion of “Auto

White Balance Standard Data Input”, “Auto White Balance
Adjustment” and “White Balance ND Filter Compensation”.
Adjusting method:
2) Select page: F, address: 27, after noting down the data, set data:
80, and press the PAUSE button of the adjustment remote
commander.
data: 00, and press the PAUSE button.
(Refer to “8. Picture Frame Setting”.)
5) Select page: 6, address: 1C, set data: 03, wait for 1 second.
6) Select page: 6, address: 01, set data: C3, and press the PAUSE
button
7) Select page: 6, address: 12, set data: 80, and wait for 1 seconds.
9) Select page: 6, address: 01, set data: C1, and press the PAUSE
button.
(The color reproduction adjustment is performed and the
adjustment data is stored in page: F, address: 51 to 58, 60 to
63.)
Note: Observe the TV monitor and check that a sign “ ” is indicated
inside each color zone.

button.
2) Select page: 6, address: 1C, and set data: 00
3) Select page: F, address: 27, set the data noted down at step 2)
4) Select page: B, address: 67, set the data noted down at step 3)
5-22
16. Color Reproduction Check
Mode STILL
(Color reproduction adjustment
frame)
Measurement Point Video output terminal
Measuring Instrument NTSC vectorscope (NTSC mode)
PAL vectorscope (PAL mode)
Specified Value Each center of all color luminance
points should settle within each color
reproduction frame.
Menu setting:
1) VIDEO OUT of SET UP menu
............................ NTSC (NTSC mode)
............................ PAL (PAL mode)
Checking method:
1) Select page: 0, address: 01, and set data: 01. PAL mode burst position
2) Select page: 5, address: F1, and set data: FF.
(Refer to “8. Picture Frame Setting”.)
data: 00, and press the PAUSE button of the adjustment remote
commander.
6) Select page: E, address: 52, after noting down the data, set
data: 0A, and press the PAUSE button.
• ND filter OFF color reproduction check
button.
10) Adjust the GAIN and PHASE of the vectorscope, and adjust
the burst luminance point to the burst position of the color
reproduction frame.
11) Check that each center of all color luminance points is settled
in each color reproduction frame.
• ND filter ON color reproduction check (MVC-FD90)
12) Select page: F, address: 27, after noting down the data, set data:
NTSC mode burst position
80, and press the PAUSE button.
13) Select page: 6, address: 1C, set data: 03, and wait for 1 second. Fig. 5-1-13.
16) Check that each center of all color luminance points is settled
in each color reproduction frame.
17) Select page: F, address: 27, after noted down at step 12), and
press the PAUSE button.

button.
2) Only for MVC-FD90 model, select page: 6, address: 1C, and
set data: 00.
5) Select page: E, address: 52, set the data noted down at step 6)
of “Checking method”, and press the PAUSE button.
6) Select page: B, address: 67, set the data noted down at step 4)
of “Checking method”, and press the PAUSE button.
5-23
17. White Balance Check
Mode STILL • OUTDOOR luminance point check
27) Place the C14 filter on the lens.
Subject Clear chart
(Color reproduction adjustment frame)
29) Select page: E, address: 4B, after noting down the data, set
Measurement Point Display data of Viode output data: 20, and press the PAUSE button.
page 1 (Note 2) terminal 30) Select page: 6, address: 01, set data: 3F, and press the PAUSE
Measuring Adjustment remote Vectorscope button.
31) Check that the center of the white luminance point settles in
Instrument commander
the circle shown Fig. 5-1-14. (B).
Specified Value R ratio: 3E00 to 4200 Fig. 5-1-14.
B ratio: 3E00 to 4200 A to B Processing after Completing Adjustments:
1) Select page: E, address: 4B, set the data noted down at step
Note 1: Refer to “8. Picture Frame setting” for XH, XL, YH and YL. 29), and press the PAUSE button.
Note 2: Displayed data of page 1 of the adjustment remote commander. 2) Select page: 6, address: 01, set data: 00, and press the PAUSE
1 : XX : XX button.
Display data 3) Select page: 6, address: 6C, and set data: 00.
4) Only for MVC-FD90 model, select page: E, address: 52, set
Checking method: the data noted down at step 9) of "Checking method", and press
1) Check that the lens is not covered with any filter. the PAUSE button.
Select page: 0, address: 01, and set data: 01. 5) Select page: 5, address: F1, and set data: 00.
2) Select page: 6, address: 90, and set data: XL. (Note1) 6) Select page: 0, address: 01, and set data: 00.
3) Select page: 6, address: 91, and set data: XH. (Note1)
4) Select page: 6, address: 92, and set data: YL. (Note1)
5) Select page: 6, address: 93, and set data: YH. (Note1)
6) Select page: 6, address: 6C, and set data: 01. R-Y 2mm
button, and wait for 1 second.
8) Select page: 6, address: 2C, and set data: 01. B-Y
• INDOOR (ND filter OFF) data check
9) Only for MVC-FD90 model, select page: E, address: 52, after
noting down the data, set data: 0E, and press the PAUSE button. 2mm
button. Fig. 5-1-14 (A).
13) Select page: 0, address: 03, and set data: 05. MVC-FD85
14) Select page: 1, and check that the display data (Note2) satisfies R-Y
the B ratio specified value. B-Y
15) Only for MVC-FD85 model, proceed to step 24). 2mm
• INDOOR (ND filter ON) data check (MVC-FD90)
16) Select page: F, address: 27, after noting down the data, set data: 3mm
80, and press the PAUSE button.
17) Select page: 6, address: 1C, set data: 03, and wait for 1 second.
3mm
20) Select page: 0, address: 03, and set data: 05. MVC-FD90
21) Select page: 1, and check that the display data (Note2) satisfies R-Y
1.0mm
the B ratio specified value. B-Y
22) Select page: F, address: 27, set the data noted down at step 16),
2mm
and press the PAUSE button.
23) Select page: 6, address: 1C, set data: 00, and wait for 1 second. 3mm
• INDOOR luminance point check
25) Select page: 5, address: F1, and set data: FF. 3mm
26) Check that the center of the white luminance point is within
the circle shown Fig. 5-1-14. (A). Fig. 5-1-14 (B).
5-24
18. Strobe White Balance Adjustment 19. Strobe Light Level and White Balance Check
Adjust the white balance when the strobe light flashes. Check the light level regulation and the white balance when the
Mode STILL strobe light flashes.
Subject A plate which reflection rate is 18 % Mode STILL
(1.0m from the front of the lens) Subject A plate which reflection rate is 18%
Adjustment Page F (1.0 m from the front of the lens)
(Note 1)
Adjustment Address 4D, 4E, 64, 69, 6A, 6B
Measurement Point Display data of page: 1
Note 1: Perform this adjustment in the dark room or use a dark box. Measuring Instrument Adjustment remote commander
Note 2: Any light other than the strobe light should not light up the plate. Specified value Y level data: 60 to 94 (Note 4)
Note 3: This adjustment should be carried out upon completion of “HALL R-Y data: FA to FF or 00 to 06
Adjustment”, “Flange Back Adjustment”, “Light Level
(Note 5)
Adjustment” and “Auto White Balance Adjustment”.
Note 4: After the power is turned on, this adjustment can be done only B-Y data: FA to FF or 00 to 06
once. (Note 5)
Switch setting: Note 1: Perform this adjustment in the dark room or use a dark box.
1) FLASH .............................................................................. ON Note 2: Any light other than the strobe light should not light up the plate.
Note 3: This adjustment should be carried out upon completion of “HALL
Adjustment”, “Flange Back Adjustment”, “Light Level
Adjusting method:
Adjustment”, “Auto White Balance Adjustment” and “Strobe White
1) Select page: 0, address: 01, and set data: 01. Balance Adjustment”.
2) Select page: 6, address: 90, and set data: 00. Note 4: Display data of pag: F, address: 64 of the adjustment remote
3) Select page: 6, address: 91, and set data: 00. commander.
4) Select page: 6, address: 92, and set data: 00. F : XX : 64
5) Select page: 6, address: 93, and set the following data. Y level data
80 : MVC-FD85
60 : MVC-FD90 Note 5: Display data of page 1 of the adjustment remote commander.
1 : XX : XX
B-Y data
7) Select page: 6, address: 2C, and set data: 01. R-Y data
button. Switch setting:
9) Select page: 6, address: 01, set data: 67, and press the PAUSE 1) FLASH .............................................................................. ON
button. (Check the flashing of the strobe light.)
10) Select page: 6, address: 01, set data: 00, and press the PAUSE Checking method:
button. 1) Select page: 0, address: 01, and set data: 01.
button. (Check the flashing of the strobe light.) 5) Select page: 6, address: 93, and set the following data.
13) Select page: 6, address: 01, set data: 00, and press the PAUSE 80 : MVC-FD85
button. 60 : MVC-FD90
14) Select page: 6, address: 01, set data: 79, and press the PAUSE 6) Select page: 6, address: 6C, and set data: 01.
button. 7) Select page: 6, address: 2C, and set data: 01.
15) Select page: 6, address: 01, set data: B9, and press the PAUSE 8) Select page: 6, address: 01, set data: 79, and press the PAUSE
button. button.
16) Check the flashing of the strobe light. 9) Select page: 6, address: 01, set data: 67, and press the PAUSE
(The strobe white balance adjustment is performed and the button.
adjustment data is stored in page: F, address: 4D, 4E, 64, 69, 10) Check the flashing of the strobe light.
6A and 6B.) 11) Select page: F, address: 64, and check that the Y level data
17) Select page: 6, address: 02, and check that the data is “01”. satisfies the specified value. (Note4)
Processing after Completing Adjustments: 13) Select page: 1, and check that the R-Y data and B-Y data satisfy
1) Select page: 6, address: 2C, and set data: 00. the specified value respectively.(Note5)
3) Select page: 6, address: 01, set data: 00, and press the PAUSE Processing after Completing Adjustments:
4) Select page: 6, address: 6C, and set data: 00. 2) Select page: 6, address: 2C, and set data: 00.
button.
5-25
20. CCD Black Defect Compensation 21. CCD White Defect Compensation
Mode STILL Mode STILL
Subject Clear chart Subject Clear chart
(25 cm from the front of the lens) (25 cm from the front of the lens)
(Note 1) (Note 1)
Adjustment Page 7 Adjustment Page 7
Adjustment Address 60 to 87 Adjustment Address 88 to AF
Note 1: Check that there are no dust, no dirt and no reflection on the clear Note 1: Check that there are no dust, no dirt and no reflection on the clear
chart. chart.
Note 2: Any subject other than the clear chart should not be in the screen. Note 2: Any subject other than the clear chart should not be in the screen.

2) Select page: F, address: DF, after noting down the data, set 2) Select page: F, address: DE, after noting down the data, set
data: 4C, and press the PAUSE button. data: 1E, and press the PAUSE button.
3) Select page: 6, address: 2C, and set data: 01. 3) Select page: F, address: E3, after noting down the data, set data:
4) Select page: 6, address: 90, and set data: 00. 08, and press the PAUSE button.
5) Select page: 6, address: 91, and set data: 03. 4) Select page: 6, address: 01, set data: 8B, and press the PAUSE
6) Select page: 6, address: 92, and set data: 00. button.
7) Select page: 6, address: 93, and set data: 00. (The CCD white defect compensation is performed and the
8) Select page: 6, address: 6C, and set data: 01. adjustment data is stored in page: 7, address: 88 to AF.)
9) Select page: 6, address: 01, set data: 79, and press the PAUSE 5) Select page: 6, address: 02, and check that the data changes to
button. “01”.
10) Select page: 6, address: 30, set data: 01, and press the PAUSE 6) Select page: 6, address: 55, and check the data.
button and wait for 4 seconds. 00 to 7F : Normal
11) Select page: 6, address: 01, set data: 8D, and press the PAUSE 80 to FF : Defective
button. 7) Select page: 6, address: 01, set data: 00, and press the PAUSE
(The CCD black defect compensation is performed and the button.
adjustment data is stored in page: 7, address: 60 to 87.) 8) Select page: F, address: DE, set data: 0F, and press the PAUSE
12) Select page: 6, address: 02, and check that the data changes to button.
“01”. 9) Select page: F, address: E3, set data: A0, and press the PAUSE
13) Select page: 6, address: 55, and check the data. button.
00 to 0A : Normal 10) Select page: 6, address: 01, set data: 87, and press the PAUSE
0B to FF : Defective button. (White defect check)
14) Select page: 6, address: 01, set data: 00, and press the PAUSE 11) Select page: 6, address: 02, and check that the data changes to
button. “01”.
15) Select page: F, address: DF, set data: 5A, and press the PAUSE 12) Select page: 6, address: 55, and check the data.
button. 00 : Normal
16) Select page: 6, address: 01, set data: 89, and press the PAUSE 01 to FF : Defective
button. (Black defect check)
17) Select page: 6, address: 02, and check that the data changes to Processing after Completing Adjustments:
“01”. 1) Select page: F, address: DE, set the data noted down at step 2),
18) Select page: 6, address: 55, and check the data. and press the PAUSE button.
00 : Normal 2) Select page: F, address: E3, set the data noted down at step 3),
01 to FF : Defective and press the PAUSE button.
Processing after Completing Adjustments: PAUSE button.
1) Select page: F, address: DF, set the data noted down at step 2), 4) Select page: 0, address: 01, and set data: 00.
and press the PAUSE button.
PAUSE button.
5-26
1-5. LCD SYSTEM ADJUSTMENT
Before perform the LCD system adjustments, check that the specified 1-5-1. LCD Type Check
values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. By measuring the resistor value between Pin qd of CN803 and Pin
Note 1: The back light (fluorescent tube) is driven by a high voltage AC 4 of CN803, the type of LCD can be discriminated.
power supply. Therefore, do not touch the back light holder to
avoid electrical shock. Resistor value LCD type Adjustment
Note 2: When replacing the LCD unit, be careful to prevent damages 4.7 kΩ TYPE SH Perform “1-5-2. LCD SYSTEM
caused by static electricity.
Note 3: Set the LCD BRIGHT (Menu) to the center. ∞ TYPE CA ADJUSTMENT (PK-50 board)”
10 kΩ TYPE SA Perform “1-5-3. LCD SYSTEM
[Adjusting connector] 22 kΩ TYPE ST ADJUSTMENT (PK-52 board)”
Most of the measuring points for adjusting the LCD system are
concentrated in CN803 of FC-72 board.
Connect the Measuring Instruments via the CPC-12 jig (J-6082-
436-A).
The following table shows the Pin No. and signal name of CN803
of FC-72 board.
Pin No. Signal Name Pin No. Signal Name
1 FDDRF B 12 LANC OUT
2 FDDRF A 13 MAKER RECOG
3 INDEX 14 PF7
4 REG GND 15 TXD
5 XCPC IN 16 RXD
6 TRAK 00 17 RESET
7 HSY 18 HI VDD
8 COM 19 EVF BL+
9 VG 20 EVF BL 4.75 V
10 HI UNREG 21 EVF VG
11 LANC IN 22 EVF VCO
CPC lid
Screw driver (–)
CPC-12 jig
22 pin flexible board
FC-72 board
CN803
Insulator side
Fig. 5-1-15.
5-27
(MVC-FD90)
1. LCD Initial Data Input 2. VCO Adjustment (PK-50 board)

Mode PLAY Set the VCO free-run frequency. If deviated, the LCD screen will
be blurred.
Signal Arbitrary
Mode PLAY
Adjustment Page D
Signal Arbitrary
Adjustment Address D0 to D9, DC to DF
Measurement Point Pin 7 of CN803 of FC-72 board
Note: Refer to “1-5-1. LCD type check” for the discrimination of the LCD
(HSY)
type. Measuring Instrument Frequency counter
Adjustment Page D
Adjusting method:
Adjustment Address D7 (NTSC)
DD (PAL)
2) Select page: D, and input the data in the following table.
Note: Press the PAUSE button of the adjustment remote commander Specified Value LCD TYPE SH:
each time to set the data. f = 15734 ± 30 Hz (NTSC)
3) Select page: 0, address: 01, and set data: 00. f = 15745 ± 30 Hz (PAL)
LCD TYPE CA:
Data
Address Remark f = 15734 ± 30 Hz (NTSC)
LCD TYPE SH LCD TYPE CA f = 15945 ± 30 Hz (PAL)
D0 AA B2 Bright adj.
D1 66 60 Color adj. Note: Refer to “1-5-1. LCD type check” for the discrimination of the LCD
D2 A8 A0 White balance adj. type.
D3 7A 6A White balance adj.
Menu setting:
D4 B8 C0 Contrast adj.
VIDEO OUT of SET UP menu ............................................ NTSC
D5 B0 54 D range adj. (This adjustment must be performed in NTSC mode, so don’t set
D6 7C 8A V-COM level adj. the menu setting to “PAL”.)
D7 6F 6F VCO adj. (NTSC)
D8 74 8A V-COM adj. Adjusting method:
D9 73 5F Fixed data
2) Select page: 5, address: F0, set data: 01.
DC B5 9A Fixed data 3) Select page: D, address: D7, change the data and set the HSY
DD 6F 4F VCO adj. (PAL) frequency (f) to the NTSC specified value.
DE 13 13 Fixed data 4) Press the PAUSE button of the adjustment remote commander.
DF 00 00 Fixed data 5) Select page: D, address: DD, change the data and set the HSY
frequency (f) to the PAL specified value.
5-28
3. D Range Adjustment (PK-50 board) 4. Bright Adjustment (PK-50 board)
Set the D range of the LCD driver to the specified value. If deviated, Set the level of the VIDEO signal for driving the LCD to the specified
the LCD screen will become blackish or saturated (whitish). value. If deviated, the screen image will be blackish or saturated
Mode PLAY (whitish).
Signal Arbitrary Mode PLAY
Measurement Point Pin 9 of CN803 of FC-72 board Signal Arbitrary
(VG) Measurement Point Pin 9 of CN803 of FC-72 board
External trigger: Pin 8 of CN803 of (VG)
FC-72 board (COM) External trigger: Pin 8 of CN803 of
Measuring Instrument Oscilloscope FC-72 board (COM)
Adjustment Page D Measuring Instrument Oscilloscope
Adjustment Address D5 Adjustment Page D
Specified Value LCD TYPE SH: A = 3.62 ± 0.05V Adjustment Address D0
LCD TYPE CA: A = 2.50 ± 0.05V Specified Value LCD TYPE SH: A = 2.00 ± 0.05V
LCD TYPE CA: A = 1.32 ± 0.05V
type. Note: Refer to “1-5-1. LCD type check” for the discrimination of the LCD
type.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01. Adjusting method:
2) Select page: 5, address: F1, set data: 03. 1) Select page: 0, address: 01, and set data: 01.
3) Select page: D, address: D5, change the data and set the voltage 2) Select page: 5, address: F1, set data: 03.
(A) between the reversed waveform pedestal and non-reversed 3) Select page: 2, address: 10, set data: 01.
waveform pedestal to the specified value. 4) Select page: D, address: D0, change the data and set the voltage
4) Press the PAUSE button of the adjustment remote commander. (A) between the pedestal and GAMMA1 limiter level to the
5) Select page: 5, address: F1, set data: 00. specified value.
6) Select page: 0, address: 01, and set data: 00. 5) Press the PAUSE button of the adjustment remote commander.
6) Select page: 2, address: 10, set data: 00.
Pedestal GAMMA 1 limiter level
2H 2H
Pedestal Pedestal
Fig. 5-1-16. Fig. 5-1-17.
5-29
5. Contrast Adjustment (PK-50 board) 6. Color Adjustment (PK-50 board)
Set the level of the VIDEO signal for driving the LCD to the specified Set the color saturation to the standard value. If deviated, the color
value. If deviated, the screen image will be blackish or saturated will be too dark or light.
(whitish). Mode PLAY
Mode PLAY Signal Arbitrary
Signal Arbitrary Measurement Point Pin 9 of CN803 of FC-72 board
Measurement Point Pin 9 of CN803 of FC-72 board (VG)
(VG) External trigger: Pin 8 of CN803 of
External trigger: Pin 8 of CN803 of FC-72 board (COM)
FC-72 board (COM) Measuring Instrument Oscilloscope
Measuring Instrument Oscilloscope Adjustment Page D
Adjustment Page D Adjustment Address D1
Adjustment Address D4 Specified Value LCD TYPE SH: A = 540 ± 50mV
Specified Value LCD TYPE SH: A = 3.17 ± 0.07V LCD TYPE CA: A = 360 ± 50mV
LCD TYPE CA: A = 2.35 ± 0.07V
Note: Refer to “1-5-1. LCD type check” for the discrimination of the LCD type.
type.
Adjusting method:
Adjusting method: 1) Select page: 0, address: 01, and set data: 01.
1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, set data: 04.
2) Select page: 5, address: F1, set data: 03. 3) Select page: D, address: D1, change the data and set the voltage
3) Select page: D, address: D4, change the data and set the voltage (A) between the white 100% (Reference level) and green to
(A) between the pedestal and 10 steps peak to the specified the specified value.
value. 4) Press the PAUSE button of the adjustment remote commander.
4) Press the PAUSE button of the adjustment remote commander. 5) Select page: 5, address: F1, set data: 00.
5) Select page: 5, address: F1, set data: 00. 6) Select page: 0, address: 01, and set data: 00.
10 steps peak
White 100 %
A
Green
2H
2H
Pedestal
Fig. 5-1-18. Fig. 5-1-19.
5-30
7. V-COM Level Adjustment (PK-50 board) 8. V-COM Adjustment (PK-50 board)
Set the common electrode drive signal level of LCD to the specified Set the DC bias of the common electrode drive signal of LCD to the
value. specified value.
Mode PLAY If deviated, the LCD display will move, producing flicker and
conspicuous vertical lines.
Signal Arbitrary
Mode PLAY
Measurement Point Pin 8 of CN803 of FC-72 board
(COM) Signal Arbitrary
Measuring Instrument Oscilloscope Measurement Point
Check on LCD display
Adjustment Page D Measuring Instrument
Adjustment Address D6 Adjustment Page D
Specified Value LCD TYPE SH: A = 6.50 ± 0.05V Adjustment Address D8
LCD TYPE CA: A = 5.65 ± 0.05V Specified Value The brightness difference between the
section A and section B is minimum.
type. Note: Perform “Bright Adjustment” and “Contrast Adjustment” before this
adjustment.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01. Adjusting method:
2) Select page: D, address: D6, change the data and set the V- 1) Select page: 0, address: 01, and set data: 01.
COM signal level (A) to the specified value. 2) Select page: 5, address: F1, set data: 02.
3) Press the PAUSE button of the adjustment remote commander. 3) Select page: 2, address: 10, set data: 02.
4) Select page: 0, address: 01, and set data: 00. 4) Select page: D, address: D8, change the data so that the
brightness of the section A and that of the section B is equal.
B A
A B
A
B A
A B
2H
Fig. 5-1-20. Fig. 5-1-21.
5-31
9. White Balance Adjustment (PK-50 board) 1-5-3. LCD SYSTEM ADJUSTMENT (PK-52 board)
Correct the white balance. (MVC-FD85)
If deviated, the LCD screen color cannot be reproduced.
Mode PLAY 1. LCD Initial Data Input
Measurement Point Signal Arbitrary
Check on LCD display Adjustment Page D
Adjustment Page D Adjustment Address D0 to D9, DC to DF
Adjustment Address D2, D3
Specified Value The LCD screen should not be type.
colored.
Adjusting method:
Note 1: Use the AC power adaptor during this adjustment. 1) Select page: 0, address: 01, and set data: 01.
Note 2: Check the white balance only when replacing the following parts. 2) Select page: D, and input the data in the following table.
If necessary, adjust them. Note: Press the PAUSE button of the adjustment remote commander
1. LCD panel each time to set the data.
2. Light induction plate 3) Select page: 0, address: 01, and set data: 00.
3. IC802
Data
Address Remark
Adjusting method: LCD TYPE SA LCD TYPE ST
1) Select page: 0, address: 01, and set data: 01. D0 20 20 Bright adj.
2) Select page: 5, address: F1, set data: 02. D1 60 60 Color adj.
3) Select page: D, address: D2 and D3, set the data to the initial
D2 A0 80 White balance adj.
value.
Note: Press the PAUSE button of the adjustment remote commander D3 90 80 White balance adj.
each time to set the data. D4 D0 D0 Contrast adj.
Address D5 90 90 Black limit adj.
Remark D6 80 80 VG center adj.
D2 D3
A8 7A LCD TYPE SH D7 70 80 VCO adj. (NTSC)
Data D8 A0 80 V-COM adj.
A0 6A LCD TYPE CA
D9 72 72 Fixed data
4) Check that the LCD screen is not colored. If colored, change DC 9A 9A Fixed data
the data of page: D, address: D2 and D3 so that the LCD screen DD 90 60 VCO adj. (PAL)
is not colored.
DE 33 33 Fixed data
Note: To write in the non-volatile memory (EEPROM), press the
PAUSE button of the adjustment remote commander each time DF 00 00 Fixed data
to set the data.
5-32
2. VCO Adjustment (PK-52 board) 3. Black Limit Adjustment (PK-52 board)
Set the VCO free-run frequency. If deviated, the LCD screen will Set the amplitude of the VIDEO signal for driving the LCD to the
be blurred. specified value. If deviated, the screen image will be blackish or
Mode PLAY saturated (whitish).
Measurement Point CH1: Signal Arbitrary
Video terminal of AUDIO/VIDEO Measurement Point Pin 9 of CN803 of FC-72 board
OUT jack (VG)
CH2: External trigger: Pin 8 of CN803 of
Pin 7 of CN803 of FC-72 board FC-72 board (COM)
(HSY) Measuring Instrument Oscilloscope
Measuring Instrument Oscilloscope Adjustment Page D
Adjustment Page D Adjustment Address D5
Adjustment Address D7 (NTSC) Specified Value LCD TYPE SA: A = 7.4 ± 0.1 V
DD (PAL) LCD TYPE ST: A = 8.0 ± 0.1 V
Specified Value LCD TYPE SA:
t = 2.05 ± 0.10 µsec (NTSC) Note: Refer to “1-5-1. LCD type check” for the discrimination of the LCD
t = 3.55 ± 0.10 µsec (PAL) type.
LCD TYPE ST:
t = 1.50 ± 0.10 µsec (NTSC) Adjusting method:
t = 2.40 ± 0.10 µsec (PAL) 1) Select page: 0, address: 01, and set data: 01.
Note: Refer to “1-5-1. LCD type check” for the discrimination of the LCD 3) Select page: D, address: D0, set data: 20.
type. 4) Select page: D, address: D5, change the data and set the voltage
(A) between the reversed waveform black limit level and non-
Menu setting: reversed waveform black limit level to the specified value.
VIDEO OUT of SET UP menu ............................................ NTSC 5) Press the PAUSE button of the adjustment remote commander.
(This adjustment must be performed in NTSC mode, so don’t set 6) Perform “Bright Adjustment”.
the menu setting to “PAL”.) 7) Select page: 0, address: 01, and set data: 00.
Adjusting method: Black limit level

2) Change the data of page: D, address: D7, and adjust the phase
difference time (t) to the NTSC specified value.
4) Change the data of page: D, address: DD, and adjust the phase
difference time (t) to the PAL specified value.
H A
CH1
CH2 2H
Black limit level
Enlargment Fig. 5-1-23.
CH1
CH2
t
Fig. 5-1-22.
5-33
4. Bright Adjustment (PK-52 board) 5. Contrast Adjustment (PK-52 board)
Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified
value. If deviated, the screen image will be blackish or saturated value. If deviated, the screen image will be blackish or saturated
(whitish). (whitish).
Mode PLAY Mode PLAY
Signal Arbitrary Signal Arbitrary
Measurement Point Pin 9 of CN803 of FC-72 board Measurement Point Pin 9 of CN803 of FC-72 board
(VG) (VG)
External trigger: Pin 8 of CN803 of External trigger: Pin 8 of CN803 of
FC-72 board (COM) FC-72 board (COM)
Measuring Instrument Oscilloscope Measuring Instrument Oscilloscope
Adjustment Page D Adjustment Page D
Adjustment Address D0 Adjustment Address D4
Specified Value LCD TYPE SA: A = 7.0 ± 0.1 V Specified Value LCD TYPE SA: A = 2.30 ± 0.05 V
LCD TYPE ST: A = 7.5 ± 0.1 V LCD TYPE ST: A = 2.30 ± 0.05 V
Note: Refer to “1-5-1. LCD type check” for the discrimination of the LCD Note: Refer to “1-5-1. LCD type check” for the discrimination of the LCD
type. type.

2) Select page: 5, address: F1, set data: 03. 2) Select page: 5, address: F1, set data: 03.
3) Select page: D, address: D0, change the data and set the voltage 3) Select page: D, address: D4, change the data and set the voltage
(A) between the reversed waveform pedestal and non-reversed (A) between the 10 steps peak and pedestal to the specified
waveform pedestal to the specified value. value.
4) Press the PAUSE button of the adjustment remote commander. 4) Press the PAUSE button of the adjustment remote commander.
5) Select page: 5, address: F1, set data: 00. 5) Select page: 5, address: F1, set data: 00.
Pedestal
A
10 steps peak
Pedestal
2H
2H
Pedestal
Fig. 5-1-24. Fig. 5-1-25.
5-34
6. Color Adjustment (PK-52 board) 7. VG Center Adjustment (PK-52 board)
Set the color saturation to the standard value. If deviated, the color Set the video signal center level of LCD panel to an appropriate
will be too dark or light. level.
Mode PLAY Mode PLAY
Signal Arbitrary Signal Arbitrary
Measurement Point Pin 9 of CN803 of FC-72 board Measurement Point Pin 9 of CN803 of FC-72 board
(VG) (VG)
External trigger: Pin 8 of CN803 of Measuring Instrument Digital voltmeter
FC-72 board (COM)
Adjustment Page D
Measuring Instrument Oscilloscope
Adjustment Address D6
Adjustment Page D
Specified Value LCD TYPE SA: A= 6.00 ± 0.05 Vdc
Adjustment Address D1 LCD TYPE ST: A= 7.00 ± 0.05 Vdc
Specified Value LCD TYPE SA: A= 470 ± 50 mV
LCD TYPE ST: A= 470 ± 50 mV Note: Refer to “1-5-1. LCD type check” for the discrimination of the LCD
type.
type. Adjusting method:
Adjusting method: 2) Select page: 5, address: F1, set data: 02.
1) Select page: 0, address: 01, and set data: 01. 3) Select page: D, address: D6, change the data and set the DC
2) Select page: 5, address: F1, set data: 04. voltage (A) of VG signal to the specified value.
3) Select page: D, address: D1, change the data and set the voltage 4) Press the PAUSE button of the adjustment remote commander.
(A) between the white 100% (Reference level) and green to 5) Select page: 5, address: F1, set data: 00.
the specified value. 6) Select page: 0, address: 01, and set data: 00.
White 100 %
A Green
2H
Fig. 5-1-26.
5-35
8. V-COM Adjustment (PK-52 board) 9. White Balance Adjustment (PK-52 board)
Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance.
specified value. If deviated, the LCD screen color cannot be reproduced.
If deviated, the LCD display will move, producing flicker and Mode PLAY
conspicuous vertical lines.
Signal Arbitrary
Mode PLAY
Measurement Point
Signal Arbitrary Check on LCD display
Measurement Point
Check on LCD display Adjustment Page D
Adjustment Address D2, D3
Adjustment Page D
Specified Value The LCD screen should not be
Adjustment Address D8 colored.
Specified Value The brightness difference between the
section A and section B is minimum. Note 1: Use the AC power adaptor during this adjustment.
Note 2: Check the white balance only when replacing the following parts.
Note: Perform “Bright Adjustment” and “Contrast Adjustment” before this If necessary, adjust them.
adjustment. 1. LCD panel
2. Light induction plate
3. IC901
Adjusting method:
Adjusting method:
4) Select page: D, address: D8, change the data so that the
3) Select page: D, address: D2 and D3, set the data to the initial
brightness of the section A and that of the section B is equal.
value.
6) Select page: 5, address: F1, set data: 00. each time to set the data.
8) Select page: 0, address: 01, and set data: 00. Address
Remark
D2 D3
A0 90 LCD TYPE SA
B A Data
80 80 LCD TYPE ST
A B 4) Check that the LCD screen is not colored. If colored, change

the data of page: D, address: D2 and D3 so that the LCD screen
is not colored.
B A Note: To write in the non-volatile memory (EEPROM), press the
PAUSE button of the adjustment remote commander each time
to set the data.
A B 5) Select page: 5, address: F1, set data: 00.
Fig. 5-1-27.
5-36
1-6. SYSTEM CONTROL SYSTEM ADJUSTMENT
1. Battery End Adjustment (FC-72 board)

Check the battery end voltage. Adjusting method:
Mode STILL 1) Adjust the output voltage of the regulated power supply so that
the digital voltmeter display is 6.1 ± 0.1Vdc.
Subject All black (Cover the lens with a black
2) Turn off the power supply.
cap)
3) Turn on the HOLD switch of the adjustment remote
Measurement Point Display data of page: 2, address: 52 commander.
Measuring Instrument Adjustment remote commander 4) Turn on the power supply.
Adjustment Page D 5) Select page: 0, address: 01, and set data: 01.
7) Decrease the output voltage of the regulated power supply so
that the digital voltmeter display is 5.50 ± 0.01Vdc.
Connection: 8) Select page: 2, address: 52, read the data, and this data is named
1) Connect the regulated power supply and the digital voltmeter Dref.
to the battery terminal as shown in Fig. 5-1-28. 9) Select page: D, address: 90, set data: Dref, and press the PAUSE
10) Convert Dref to decimal notation, and obtain Dref’. (Refer to
Table 5-2-1. “Hexadecimal-decimal conversion table” of “5-2.
Service mode”)
11) Calculate D91', D92', D93', and D94 using following equations
(decimal calculation), convert it to a hexadecimal number, and
input each adjustment address.
Address: 91 D91' = Dref’+5
Note: After setting each data, be sure to press the PAUSE button.
Regulated power supply Digital voltmeter
1
2
3
CN002 4
Expansion figure
Lens block Cover the lens with a black cap.

Power coda
(J-6082-223-A)
Flexible of MF unit
(MVC-FD90 model only)
Need not to be connected.
LCD
FDD unit
FU-146/140 board CN002 FU-146 board : MVC-FD85 model

FU-140 board : MVC-FD90 model
Fig. 5-1-28.
5-37
2. Alignment Check (FDD UNIT)
Confirm that the FDD alignment is within the specifications.
If deviated, reading and writing data from and to the floppy disk
become impossible. Or compatibility of the floppy disk with other
machines can be lost.
Mode Playback
Signal Alignment disks (TFD2-1(+) and
TFD2-2(–)): Arbitrary signal
Measurement Point
Check on LCD screen
Specified Value The playback pictures should be
normal.
Checking method:
1) Disconnect the adjustment remote commander.
2) Insert the alignment disk TFD2-1(+) (+17.5 µm).
3) Playback arbitrary signal and check that the playback picture
is normal.
4) Insert the alignment disk TFD2-2(–) (–17.5 µm).
5) Playback arbitrary signal and check that the playback picture
is normal.
[Alignment disk]
Use the alignment disks (two disks as pair) shown in below.
Disk-1: TFD2-1(+) (Parts code: 8-967-990-01)
Disk-2: TFD2-2(–) (Parts code: 8-967-990-11)
Contents of alignment disk

TFD2-1(+): (Common signal) + (+17.5 µm alignment)
TFD2-2(–): (Common signal) + (–17.5 µm alignment)
Common signal
File name Signal
MVC-001C.JPG Color bars
MVC-002M.JPG Monoscope
MVC-003V.JPG V-COM adjustment signal
MVC-004W.JPG 100% white
MVC-005H.JPG 50% white
MVC-006T.JPG Stair-step signal of 10 step
MVC-007R.JPG Red single color
MVC-008G.JPG Green single color
MVC-009B.JPG Blue single color
MVC-010D.JPG Camera color bars
MVC-011N.JPG Camera monoscope
5-38
5-2. SERVICE MODE
2-1. ADJUSTMENT REMOTE COMMANDER
The adjustment remote commander is used for changing the
calculation coefficient in signal processing, EVR data, etc. The
adjustment remote commander performs bi-directional
communication with the unit using the remote commander signal
line (LANC). The resultant data of this bi-directional communication
is written in the non-volatile memory.
1. Using the Adjustment Remote Commander 2. Precautions Upon Using

1) Connect the adjustment remote commander to the following the Adjustment Remote Commander
connector or jack. Mishandling of the adjustment remote commander may erase the
• CN803 of FC-72 board via CPC-12 jig (J-6082-436-A) correct adjustment data at times. To prevent this, it is recommended
• LANC jack (MVC-FD90 model only) that all adjustment data be noted down before beginning adjustments
2) Set the HOLD switch of the adjustment remote commander to and new adjustment data after each adjustment.
“HOLD” (SERVICE position). If it has been properly
connected, the LCD on the adjustment remote commander will
display as shown in Fig. 5-2-1.
Page Data Address
Fig. 5-2-1.
3) Operate the adjustment remote commander as follows.

• Changing the page
The page increases when the EDIT SEARCH+ button is
pressed, and decreases when the EDIT SEARCH– button is
pressed. There are altogether 16 pages, from 0 to F.
Hexadecimal
notation 0 1 2 3 4 5 6 7 8 9 A B C D E F
LCD Display 0 1 2 3 4 5 6 7 8 9 A b c d E F
Decimal notation
conversion value 0 1 2 3 4 5 6 7 8 9 1011 12 1314 15
• Changing the address

The address increases when the FF (M) button is pressed,
and decreases when the REW (m) button is pressed. There
are altogether 256 addresses, from 00 to FF.
• Changing the data (Data setting)
The data increases when the PLAY (N) button is pressed,
and decreases when the STOP (x) button is pressed. There
are altogether 256 data, from 00 to FF.
• Writing the adjustment data
The PAUSE button must be pressed to write the adjustment
data (B, D, E, F, 7 page) in the nonvolatile memory. (The
new adjusting data will not be recorded in the nonvolatile
memory if this step is not performed.)
4) After completing all adjustments, turn off the main power
supply once.
5-39
2-2. DATA PROCESS
The calculation of the DDS display and the adjustment remote
commander display data (hexadecimal notation) are required for
obtaining the adjustment data of some adjustment items. In this case,
after converting the hexadecimal notation to decimal notation,
calculate and convert the result to hexadecimal notation, and use it
as the adjustment data. Indicates the hexadecimal-decimal
conversion table.
Hexadecimal-decimal Conversion Table 2

Lower digit of
hexadecimal 0 1 2 3 4 5 6 7 8 9 A B C D E F
Upper digit (A) (b) (c) (d) (E) (F)
of hexadecimal
0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
2 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
3 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
4 64 65 66 67 68 69 70 71 72 73 74 77 76 77 78 79
5 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95
6 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111
7 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127
8 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143
9 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159
A (A) 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175
1 B (b) 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191
C (c) 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207
D (d) 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223
E (E) 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239
F (F) 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255
Note: The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander.
(Example) If the DDS display or the adjustment remote commander shows BD (bd);
Because the upper digit of the adjustment number is B (b), and the lower digit is D (d), the meeting point
“189” of 1 and 2 in the above table is the corresponding decimal number.
Table. 5-2-1.
5-40
2-3. SERVICE MODE
1. Setting the Test Mode 3. Emergency Memory Address of Flash Unit

Page D Address 10 Page D Address 67
Data Function Data Function

00 Normal 00 No error
01 Forced STILL mode power ON 04 Flash unit emergency
02 Forced PLAY mode power ON
03 Forced MOVIE mode power ON Using method:
1) When emergency occurs in the flash unit, the data
• Before setting the data, select page: 0, address: 01, and set data: corresponding to the error is written in the address
01. Note: When replacing the flash unit, initialize this data.
• For page D, the data set is recorded in the non-volatile memory
by pressing the PAUSE button of the adjustment remote Initializing method:
commander. In this case, take note that the test mode will not be 1) Select page: 0, address: 01, and set data: 01.
exited even when the main power is turned off. 2) Select page: D, address: 67, set data: 00, and press the PAUSE
• After completing adjustments/repairs, be sure to return the data button of the adjustment remote commander.
of this address to “00”, and press the PAUSE button of the 3) Select page: 0, address: 01, and set data: 00.
adjustment remote commander.
Select page: 0, address: 01, and set data: 00.
2. Bit Value Discrimination

Bit values must be discriminated using the display data of the
adjustment remote commander for following items. Use the table
below to discriminate if the bit value is “1” or “0”.
Display on the adjustment remote commander
Address
Page bit3 to bit0 discrimination
bit7 to bit4 discrimination
Display on the Bit values

adjustment bit3 bit2 bit1 bit0
remote or or or or
commander bit7 bit6 bit5 bit4
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
A 8 1 0 0 0
9 1 0 0 1
A (A) 1 0 1 0
B (b) 1 0 1 1
C (c) 1 1 0 0
D (d) 1 1 0 1
B E (E) 1 1 1 0
F (F ) 1 1 1 1
Example: If “8E” is displayed on the adjustment remote commander, the
bit values for bit7 to bit4 are shown in the A column, and the
bit values for bit3 to bit0 are shown in the B column.
5-41
4. Record of Use check
Page D Address 6C to 6F
Address Function Remarks
6C Recording counter Counter data 1
6D (Hexadecimal) Counter data 2
6E Counter data 3
6F Recording counter (Hexadecimal) / Counter data 4
MC CAM emergency Note: When this data is “80” to “FF”, the MC CAM (FC-72 board IC501) is abnormal.
Note: When replacing the floppy disk drive unit, initialize these data.
Using method:
1) The recording counter data is displayed at page: D, addresses:
6C to 6F. These data are named D 6C, D6D, D 6E and D 6F
respectively.
2) Convert D6C, D6D, D6E and D6F to decimal notation, and obtain
D6C’, D6D’, D6E’ and D6F’.
(Refer to Table 5-2-1. “Hexadecimal-decimal conversion table”)
3) Calculate the recording counter (N) using following equation.
(Decimal calculation)
N = D6C’ + D6D’ × 256 + D6E’ × 65536 + D6F’ × 16777216
Initializing method:
2) Select page: D, address: 6C to 6F, and write data: 00 to each
address.
5. Self Diagnostics Log check

Page 2 Address 90 to A2
Address Function Example:

90 1st error occurrence code C : 32 : 01
Address : 92, 95, 98, 9B, 9E, A1
91
Address : 91, 94, 97, 9A, 9D, A0
92 Address : 90, 93, 96, 99, 9C, 9F (Note)
93 2nd error occurrence code
94 Note: “C” → “01”
“E” → “03”
95
96 3rd error occurrence code
97
98
99 4th error occurrence code
9A
9B
9C 5th error occurrence code
9D
9E
9F 6th error occurrence code
A0
A1
A2 Numbers of error occurrence (0 to 6)
Using method:
1) The self diagnostics log is displayed at page: 2, addresses: 90
to A2.
Note: This data will be erased when the battery or DC power supply
is removed.
5-42
6. Switch Check (1)
Page 2 Address 43
Bit Function When bit value = 1 When bit value = 0

0 XPOWER SW OFF ON
(PK-52/50 board S703)
1 XCAM/PLAY SW PLAY STILL or MOVIE
(PK-52/50 board S708)
2 SHUTTR SW OFF ON
3 XSHUTTER LOCK SW OFF ON
(ZOOM/RELEASE block)
4 DISK IN SW (FDD unit) IN OUT
5
6
7 XSTILL/MOVIE SW MOVIE STILL or PLAY
(PK-52/50 board S710)
Note: PK-52 board: MVC-FD85
PK-50 board: MVC-FD90
Using method:
1) Select page: 2, address: 43.
2) By discriminating the bit value of display data, the state of the
switches can be discriminated.
7. Switch Check (2)

Page 2 Address 54 to 56
Using method:
1) Select page: 2, address: 54 to 56.
2) By discriminating the display data, the pressed key can be
discriminated.
Data
Address
00 to 12 13 to 3A 3B to 62 63 to 87 88 to B3 B4 to D5 D6 to FF
54 FOCUS MANUAL FOCUS AUTO
(KEY AD0) (MF block) (MF block)
(IC404 uk) (S001)Note1 (S001)Note1
55 CONTROL DOWN CONTROL UP DISPLAY VOLUME + VOLUME – MACRO No key input
(KEY AD1) (PK-52/50 board) (PK-52/50 board) (PK-52/50 board) (PK-52/50 board) (PK-52/50 board) (PK-52/50 board)
(IC404 ul) (S701) (S701) (S702) (S704) (S706) (S711)
56 CONTROL RIGHT CONTROL LEFT CONTROL SET FLASH PROGRAM AE LCD BACKLIGHT LCD BACKLIGHT
(KEY AD2) (PK-52/50 board) (PK-52/50 board) (PK-52/50 board) (PK-52/50 board) (PK-52/50 board) OFF ON
(IC404 i;) (S701) (S701) (S701) (S705) (S707) (PK-52/50 board) (PK-52/50 board)
(S709) (S709)
Note: MVC-FD90 model only.
8. LED Check
Page 2 Address 06 Bit1
Using method:
1) Select page: 2, address: 06, and set the bit value of Bit1 to “1”.
2) Check that all LED except for the ACCESS LED are lit.
3) Select page: 2, address: 06, and set the bit value of Bit1 to “0”.
5-43E
MVC-FD85/FD90
SECTION 6
REPAIR PARTS LIST
6-1. EXPLODED VIEWS

NOTE:
• -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark 0or
have some differences from the original one. in the exploded views are not supplied. dotted line with mark 0 are critical for safety.
• Items marked “*” are not stocked since they • Abbreviation Replace only with part number specified.
are seldom required for routine service. Some FD85: MVC-FD85 Les composants identifiés par une marque
delay should be anticipated when ordering these FD90: MVC-FD90 0 sont critiques pour la sécurité.
items. Ne les remplacer que par une pièce portant
le numéro spécifié.
6-1-1. CABINET (FRONT) BLOCK SECTION-1
3 (MVC-FD90) (MVC-FD85)
A
DC J 4 16
4
17
K 3 F 13
F I J B
I
F 18
2 H G H 4
-7
FCard G
Bo 5 4
11 I 14
3 MIC901
12 20
1 2 A 19
B
C K
D 10 4
7 E
6 1
9
1 4 E
21
1 FU 0 1
8 -1
4
1 15
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 3-968-729-01 SCREW(M2), LOCK ACE, P2 (FD85) 9 1-960-461-11 HARNESS (FU-052)

1 3-968-729-91 SCREW(M2), LOCK ACE, P2 (FD90) 10 1-960-460-11 HARNESS (FU-051)
2 A-7096-140-A FC-72(90) BOARD, COMPLETE 11 1-794-045-21 CONNECTOR, DC-IN
(SERVICE)(FD90) * 12 3-062-299-01 SHEET, MICROPHONE
2 A-7096-166-A FC-72 (85) BOARD, COMPLETE * 13 3-058-801-01 SHEET, ST INSULATING
(SERVICE)(FD85)
3 7-627-854-07 PRECISION SCREW +P 2X2.5 TYPE3 14 1-418-995-11 FLASH UNIT
15 3-062-223-01 SHEET, BLIND
4 3-948-339-01 SCREW, TAPPING (FD85) 16 3-058-765-01 COVER, MICROPHONE
4 3-948-339-61 TAPPING (FD90) * 17 3-058-797-01 CUSHION, MICROPHONE
5 3-058-762-01 BRACKET, FC 18 3-058-764-01 HOLDER, MICROPHONE
6 1-772-563-11 DRIVE, FLOPPY DISK
* 7 3-061-228-01 RETAINER, HARNESS 19 3-058-766-01 RETAINER, DC
20 X-3950-660-1 CAP ASSY, LENS
8 A-7074-298-A FU-140 MOUNT (FD90) 21 3-724-594-01 STRING, CAP
8 A-7074-417-A FU-146 MOUNT (FD85) MIC901 1-542-428-11 MICROPHONE UNIT
6-1
6-1-2. CABINET (FRONT) BLOCK SECTION-2
63 J901 (MVC-FD90)
56 65
56
67 73 74
66
62 not (MVC-FD85)
supplied 56
56 61 not supplied
75
68
60 69
59 64
56 58
55
57
54 70
A
56 76
53
A not not supplied
supplied 64
52 (MVC-FD90)
51 71 72
51 X-3950-245-1 CABINET (FRONT) ASSY (FD90) 64 X-3949-747-1 LABEL ASSY, LENS (FD90)
51 X-3950-606-1 CABINET (FRONT) ASSY (FD85) 64 X-3950-608-1 LABEL ASSY, LENS (FD85)
52 3-058-747-01 LID,BATTERY 65 1-418-894-11 SWITCH BLOCK, CONTROL (Zoom and shutter)
53 3-058-748-01 KNOB, B LOCK 66 3-058-742-01 HOLDER, SW
54 3-058-749-01 LEVER, B LOCK 67 1-418-895-11 SWITCH BLOCK, CONTROL (MF 330) (FD90)
55 3-058-802-01 SPRING, B LOCK 68 3-058-803-01 HOLDER, HARD STEEL

56 3-948-339-01 SCREW, TAPPING (FD85) 69 3-058-744-01 WINDOW, HARD STEEL
56 3-948-339-61 TAPPING (FD90) 70 3-058-755-01 SCREW, TRIPOD
57 X-3950-246-1 HOLDER ASSY, HINGE 71 3-719-381-01 SCREW (M2X4)
* 58 3-058-753-01 RETAINER, HINGE 72 3-058-767-01 COVER, DC
59 3-736-363-41 TAPPING 73 3-968-729-01 SCREW (M2), LOCK ACE, P2

60 3-969-380-01 SPRING, BATTERY 74 3-058-754-01 SHEET METAL (L), STRAP
* 61 3-058-746-01 HOLDER, BATTERY 75 3-713-791-01 SCREW (M1.7X5), TAPPING, P2
62 3-052-574-01 CLAW, BT LOCK * 76 3-058-756-01 GEAR, MF (FD90)
* 63 3-056-033-02 SHEET, FLEXIBLE RETAINER J901 1-694-297-21 TERMINAL BOARD, BATTERY
6-2
6-1-3. CABINET (REAR) BLOCK SECTION
Note 1: LCD type check

106 By measuring the resistor value between
not supplied Pin qd of CN803 (FC-72 board) and Pin 4 of
CN803 (FC-72 board), the type of LCD can be discriminated.
115
Type SA : 10 kΩ
114 Type ST : 22 kΩ
113 Type CA : ∞
Type SH : 4.7 kΩ
LCD901 (Note 1)
111 112 A ND901
102 110
119 106
109
107
101 105 106
108 SP901
(Note 2) 106
A 106
104 103 -
118 PKard
117 120 Bo
123
121
116 (Note 1)
122
Note 2: Refer to "Eject button section" on page 2-7
when installing the Rack (A). 106
: BT701(Lithium battery) PK board on the mount position.

(See page 4-31, 4-35)
101 X-3950-247-2 CABINET (REAR) ASSY (FD90) * 118 3-058-791-01 RETAINER, SPEAKER
101 X-3950-607-1 CABINET (REAR) ASSY (FD85) * 119 3-058-799-01 RETAINER, BACK LIGHT
102 3-058-792-01 LID, CPC 120 3-055-028-11 BUTTON, FUNCTION
103 3-355-424-21 SCREW, TAPPING 121 A-7074-300-A PK-50 (CASI) BOARD, COMPLETE (FD90)(CA)
104 3-058-787-01 RACK (A) 121 A-7074-418-A PK-52 (85SC) BOARD, COMPLETE (FD85)(ST)
105 3-058-790-01 SPRING, EJECT 121 A-7074-419-A PK-52 (85SNY) BOARD, COMPLETE (FD85)(SA)
106 3-948-339-61 TAPPING 121 A-7074-301-A PK-50 (SHAP) BOARD, COMPLETE (FD90)(SH)
107 3-058-789-01 COVER, GEAR 122 1-677-897-11 PWB, FP-165 FLEXIBLE
108 3-058-788-01 RACK (B) * 123 X-3950-248-1 CASE (LOWER) ASSY, PK SHIELD
109 3-703-357-04 PIN, PARALLEL (DIA. 1.6X8) 0 ND901 1-517-787-21 TUBE, FLUORESCENT,COLD CATHODE
110 3-058-786-01 GEAR, PINION SP901 1-505-862-41 SPEAKER (2.0 CM)

111 3-058-782-01 KNOB, EJECT LCD901 1-803-860-21 INDICATOR MODULE LIQUID CRYST (FD90)
112 3-058-785-01 SPRING, LOCK BUTTON (CA)
113 3-058-783-01 BUTTON, LOCK LCD901 1-803-858-21 INDICATOR MODULE LIQUID CRYST (FD90)
114 3-058-784-01 RETAINER, LOCK BUTTON (SH)
LCD901 8-753-050-21 INDICATOR MODULE LIQUID CRYST (FD85)
115 3-058-770-01 SHEET METAL (R), STRAP (ST)
* 116 3-056-012-01 RETAINER (190), WINDOW LCD901 1-803-997-21 INDICATOR MODULE, LIQUID CRYST (FD85)
117 3-052-592-01 WINDOW, LCD (SA)
Note : Note :
mark ! or dotted line with mark une marque ! sont critiques
! are critical for safety. pour la sécurité.
6-3
6-1-4. LENS BLOCK SECTION
(MVC-FD90)
161 170
not
supplied
169
165 170
164
167
168
160
IC101
163 166
M901
not
M903 supplied
157
162 157
not
supplied 158
M902 152
157
171
151 153 IC201 not

supplied
154
not
155 supplied M905
156 M904
not
supplied
(MVC-FD85) 159
Be sure to read “Precautions Upon Replacing CCD Imager”

on page 4-6,8 when changing the CCD imager.
151 1-677-903-11 PWB, FP-231 FLEXIBLE (FD85) 165 A-7074-299-A CD-246 BOARD, COMPLETE (FD90)
152 3-060-822-01 FRAME (L), LENS (FD85) 166 3-968-054-11 RUBBER (FM), SHIELD (FD90)
153 A-7074-415-A CD-248 BOARD, COMPLETE (FD85) 167 1-758-322-21 FILTER BLOCK, OPTICAL (FD90)
154 3-060-714-01 RUBBER (CL), SEAL (FD85) 168 3-963-467-11 ADAPTOR (FH), CCD FITTING (FD90)
155 1-758-435-11 FILTER BLOCK, OPTICAL (FD85) 169 3-058-763-01 FRAME, LENS (FD90)
156 3-058-032-01 ADAPTOR (CL), CCD FITTING (FD85) 170 3-948-339-61 TAPPING (FD90)
157 3-948-339-01 SCREW, TAPPING (FD85) 171 3-947-268-11 TITE (2), +B TAPPING (P)
158 3-061-627-01 SHEET (L), LENS (FD85) IC101 A-7031-083-A CCD BLOCK ASSY (CCD imager) (FD90)
159 1-758-415-11 LENS, ZOOM (VCL-6103WA) (FD85) IC201 A-7031-090-A CCD BLOCK ASSY (CCD imager) (FD85)
* 160 3-060-212-01 SHEET, LENS (FD90) M901 3-709-498-01 MOTOR, ZOOM STEPPING (FD90)
161 3-062-058-01 ISB SHEET (FD90) M902 3-709-497-01 MOTOR, FOCUS STEPPING (FD90)
162 1-758-475-11 LENS, VIDEO (61JC) (FD90) M903 3-709-499-01 METER, ND (FD90)
163 1-677-898-11 PWB, FP-167 FLEXIBLE (FD90) M904 3-709-573-01 MOTOR UNIT, FOCUS (FD85)
164 3-318-203-11 SCREW (B1.7X6), TAPPING M905 3-709-574-01 MOTOR UNIT, ZOOM (FD85)
6-4
CD-246 CD-248
6-2. ELECTRICAL PARTS LIST

NOTE:
• Due to standardization, replacements in the • COILS • LCD type check
parts list may be different from the parts uH: µH By measuring the resistor value between Pin
specified in the diagrams or the components • SEMICONDUCTORS qd of CN803 (FC-72 board) and Pin 4 of
used on the set. In each case, u: µ, for example: CN803 (FC-72 board), the type of LCD can be
• -XX, -X mean standardized parts, so they uA...: µA... , uPA... , µPA... , discriminated.
may have some difference from the original uPB... , µPB... , uPC... , µPC... , Type SA: 10 kΩ
one. uPD..., µPD... Type ST: 22 kΩ
• Items marked “*” are not stocked since they • Abbreviation Type CA: ∞
are seldom required for routine service. FD85 : MVC-FD85 Type SH: 4.7 kΩ
Some delay should be anticipated when FD90 : MVC-FD90
ordering these items. CND : Canadian model.
• RESISTORS AUS : Australian model.
All resistors are in ohms. JE : Tourist model. The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
METAL: metal-film resistor HK : Hong Kong model.
Replace only with part number specified.
METAL OXIDE: Metal Oxide-film resistor CN : Chinese model.
Les composants identifiés par une marque
F: nonflammable KR : Korea model.
0 sont critiques pour la sécurité.
• CAPACITORS: When indicating parts by reference number, Ne les remplacer que par une pièce portant
uF: µF please include the board name. le numéro spécifié.
A-7074-299-A CD-246 BOARD, COMPLETE (FD90) A-7074-415-A CD-248 BOARD, COMPLETE (FD85)
*********************** ***********************
(REF.NO.;2000 Series) (REF.NO.;3000 Series)
(IC101 is not included in this completed board) (IC201 is not included in this completed board)
< CAPACITOR > 1-678-138-11 PWB,CD-248 (FD85)
C101 1-113-985-11 TANTAL. CHIP 10uF 20% 20V < CAPACITOR >
C102 1-119-751-11 TANTAL. CHIP 22uF 20% 16V
C103 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C201 1-113-985-11 TANTAL. CHIP 10uF 20% 20V
C104 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V C202 1-119-751-11 TANTAL. CHIP 22uF 20% 16V
C105 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C203 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C204 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C108 1-164-156-11 CERAMIC CHIP 0.1uF 25V C205 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C109 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
< CONNECTOR > C207 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C208 1-164-156-11 CERAMIC CHIP 0.1uF 25V
CN101 1-691-356-21 CONNECTOR, FFC/FPC (ZIF) 18P C209 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
< IC > < CONNECTOR >
IC101 A-7031-083-A CCD BLOCK ASSY (CCD imager) CN201 1-764-526-11 CONNECTOR, FFC/FPC 18P
< COIL > < IC >
L101 1-414-757-11 INDUCTOR 100uH IC201 A-7031-090-A CCD BLOCK ASSY (CCD imager)
< TRANSISTOR > < COIL >
Q102 8-729-117-73 TRANSISTOR 2SC4178-F13F14-T1 L201 1-414-757-11 INDUCTOR 100uH
< RESISTOR > < TRANSISTOR >
R101 1-216-864-11 METAL CHIP 0 5% 1/16W Q201 8-729-037-74 TRANSISTOR UN9213J-(K8).SO

R103 1-216-813-11 METAL CHIP 220 5% 1/16W Q202 8-729-117-73 TRANSISTOR 2SC4178-F13F14-T1
R104 1-216-804-11 METAL CHIP 39 5% 1/16W
R105 1-216-804-11 METAL CHIP 39 5% 1/16W < RESISTOR >
R106 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R201 1-216-864-11 METAL CHIP 0 5% 1/16W
R107 1-216-857-11 METAL CHIP 1M 5% 1/16W R202 1-216-864-11 METAL CHIP 0 5% 1/16W
R108 1-216-827-11 METAL CHIP 3.3K 5% 1/16W R203 1-216-813-11 METAL CHIP 220 5% 1/16W
R109 1-216-864-11 METAL CHIP 0 5% 1/16W R204 1-216-804-11 METAL CHIP 39 5% 1/16W
R112 1-216-296-91 SHORT 0
**************************************************************

6-5
CD-248 FC-72
R206 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R207 1-216-857-11 METAL CHIP 1M 5% 1/16W
R208 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R209 1-216-864-11 METAL CHIP 0 5% 1/16W
R210 1-216-805-11 METAL CHIP 47 5% 1/16W
R212 1-216-296-91 SHORT 0

**************************************************************
A-7096-166-A FC-72(85) BOARD, COMPLETE (SERVICE)

(FD85)
*************************
A-7096-140-A FC-72(90) BOARD, COMPLETE (SERVICE)
(FD90)
*************************
(REF.NO.;1000 Series)
**************************************************************
Electrical parts list of the FC-72 board is

not shown.
pages 6-7 to 6-14 are not shown.
6-6
FU-140 FU-146 PK-50 (FD90)
A-7074-298-A FU-140BOARD, COMPLETE (FD90) A-7074-300-A PK-50(CASI) BOARD, COMPLETE (FD90)(CA)
********************** ***************************
A-7074-417-A FU-146BOARD, COMPLETE (FD85) A-7074-301-A PK-50(SHAP) BOARD, COMPLETE (FD90)(SH)
********************** ***************************
(REF.NO.;4000 Series) (REF.NO.;5000 Series)
< CAPACITOR > < BATTERY >
C001 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V BT701 1-528-900-11 BATTERY, LITHIUM SECONDARY
< CONNECTOR > < CAPACITOR >
* CN001 1-580-056-21 PIN, CONNECTOR (SMD) 3P C705 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
* CN002 1-580-057-11 PIN, CONNECTOR (SMD) 4P C706 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
CN003 1-770-626-21 PIN, CONNECTOR 9P C710 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
CN004 1-770-629-21 PIN, CONNECTOR 12P C711 1-162-925-11 CERAMIC CHIP 68PF 5% 50V
CN005 1-779-327-11 CONNECTOR, FFC/FPC 6P C801 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< DIODE > C802 1-164-156-11 CERAMIC CHIP 0.1uF 25V

D001 8-719-158-49 DIODE MA8120-TX C804 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
D002 8-719-027-76 DIODE 1SS357-TPH3 C805 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
D003 8-719-045-87 DIODE MA4Z082WA-(TX).SO C806 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
< FUSE > C807 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
0 F001 1-576-406-11 FUSE, MICRO (1608)(1.4A/32V) C810 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
0 F002 1-576-406-11 FUSE, MICRO (1608)(1.4A/32V) C811 1-104-851-11 TANTAL. CHIP 10uF 20% 10V
0 F003 1-576-406-11 FUSE, MICRO (1608)(1.4A/32V) C812 1-104-851-11 TANTAL. CHIP 10uF 20% 10V
0 F004 1-576-406-11 FUSE, MICRO (1608)(1.4A/32V)
0 F005 1-576-406-11 FUSE, MICRO (1608)(1.4A/32V) C813 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< FERRITE BEAD > C815 1-165-112-11 CERAMIC CHIP 0.33uF 20% 10V
FB001 1-414-228-11 INDUCTOR CHIP 0UH C851 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
FB002 1-414-228-11 INDUCTOR CHIP 0UH
FB003 1-414-228-11 INDUCTOR CHIP 0UH C852 1-119-751-11 TANTAL. CHIP 22uF 20% 16V
< LINE FILTER > C854 1-135-149-21 TANTALUM CHIP 2.2uF 20% 10V
LF001 1-411-957-11 FILTER, COMMON MODE C856 1-162-918-11 CERAMIC CHIP 18PF 5% 50V
< TRANSISTOR > C857 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
Q001 8-729-051-49 TRANSISTOR TPC8305(TE12L) C859 1-162-920-11 CERAMIC CHIP 27PF 5% 50V
Q002 8-729-804-41 TRANSISTOR 2SB1122-ST-TD C861 1-113-682-11 TANTAL. CHIP 33uF 20% 10V
Q003 8-729-037-74 TRANSISTOR UN9213J-(K8).SO C862 1-115-156-11 CERAMIC CHIP 1uF 10V
Q004 8-729-047-68 TRANSISTOR SSM3K03FE(TPL3)
Q005 8-729-047-68 TRANSISTOR SSM3K03FE(TPL3) C863 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
< RESISTOR > C865 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
0 C866 1-131-959-91 CERAMIC CHIP 12PF 10% 3KV
R001 1-216-821-11 METAL CHIP 1K 5% 1/16W
R002 1-216-853-11 METAL CHIP 470K 5% 1/16W C901 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
R004 1-216-821-11 METAL CHIP 1K 5% 1/16W (CA)
R005 1-216-831-11 METAL CHIP 6.8K 5% 1/16W C902 1-107-687-11 TANTAL. CHIP 3.3uF 20% 20V
R006 1-216-857-11 METAL CHIP 1M 5% 1/16W C903 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
(CA)
R008 1-216-864-11 METAL CHIP 0 5% 1/16W C903 1-107-826-11 CERAMIC CHIP 0.1uF 10% 10V
R019 1-216-841-11 METAL CHIP 47K 5% 1/16W (SH)
R020 1-216-150-91 RES-CHIP 10 5% 1/8W C904 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R021 1-216-864-11 METAL CHIP 0 5% 1/16W C905 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R022 1-216-864-11 METAL CHIP 0 5% 1/16W
R023 1-216-864-11 METAL CHIP 0 5% 1/16W

**************************************************************
Note : Note :
6-15
PK-50 (FD90)
C906 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V < IC >
C908 1-162-926-11 CERAMIC CHIP 82PF 5% 50V IC702 8-759-572-54 IC TA6009FN(EL)
C909 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V IC801 8-759-364-05 IC MB40D001PFV-G-BND-ER
C911 1-164-739-11 CERAMIC CHIP 560PF 5% 50V IC802 8-759-539-27 IC IR3Y37A4
IC803 8-759-196-97 IC TC7SH32FU-TE85R
C912 1-162-926-11 CERAMIC CHIP 82PF 5% 50V IC851 8-759-521-35 IC TL5001CDR
C913 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C914 1-113-994-11 TANTAL. CHIP 6.8uF 20% 16V IC852 8-759-710-82 IC NJM2406F-TE2
(SH) IC901 8-759-524-61 IC CM7018L3-T4 (CA)
C915 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V IC901 8-759-587-61 IC LZ9GH234 (SH)
(SH) IC902 8-759-327-01 IC NJM062V(TE2)
< JACK >
C918 1-164-505-11 CERAMIC CHIP 2.2uF 16V J781 1-695-514-31 JACK (SMALL TYPE) 1P
C919 1-164-156-11 CERAMIC CHIP 0.1uF 25V (AUDIO(MONO)VIDEO OUT)
(CA) J782 1-793-995-21 JACK, SUPER SMALL TYPE ( EXT FLASH)
< CONNECTOR > < COIL >
CN701 1-778-637-21 CONNECTOR, FFC/FPC (ZIF) 50P L702 1-414-756-11 INDUCTOR 47uH
CN702 1-784-342-11 HOUSING, CONNECTOR 2P L801 1-414-757-11 INDUCTOR 100uH
CN851 1-691-358-21 CONNECTOR, FFC/FPC (ZIF) 20P L802 1-414-754-11 INDUCTOR 10uH
CN901 1-691-388-11 CONNECTOR, FFC/FPC 24P L851 1-414-753-91 INDUCTOR 4.7uH
L852 1-424-674-11 INDUCTOR 22uH
< DIODE >
L853 1-419-387-21 INDUCTOR 100uH
D701 8-719-061-81 DIODE TLYU1002(TPX1,SONY) L901 1-414-754-11 INDUCTOR 10uH
D702 8-719-061-81 DIODE TLYU1002(TPX1,SONY) L902 1-414-754-11 INDUCTOR 10uH
D703 8-719-064-05 DIODE TLGU1002(TPX1,SONY) L903 1-414-754-11 INDUCTOR 10uH
D782 8-719-045-87 DIODE MA4Z082WA-(TX).SO L904 1-414-754-11 INDUCTOR 10uH (CA)
D783 8-719-045-87 DIODE MA4Z082WA-(TX).SO
L905 1-412-949-21 INDUCTOR 6.8uH
D784 8-719-073-01 DIODE MA111-(K8).S0
D785 8-719-073-01 DIODE MA111-(K8).S0 < TRANSISTOR >
D787 8-719-045-87 DIODE MA4Z082WA-(TX).SO Q851 8-729-045-75 TRANSISTOR RN1107F(TPL3)
Q853 8-729-042-29 TRANSISTOR RN1104F(TPL3)
D789 8-719-045-87 DIODE MA4Z082WA-(TX).SO Q854 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO
D853 8-719-073-01 DIODE MA111-(K8).S0
D902 8-713-102-80 DIODE 1T369-01-T8A Q856 8-729-823-84 TRANSISTOR FP102-TL
D903 8-719-976-96 DIODE MA8047-H-TX Q857 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO
Q858 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO
< FERRITE BEAD > Q859 8-729-042-29 TRANSISTOR RN1104F(TPL3)
Q860 8-729-039-43 TRANSISTOR FP216-TL
FB782 1-414-633-22 INDUCTOR CHIP 0UH Q861 8-729-045-83 TRANSISTOR RN2103F(TPL3)
FB783 1-414-633-22 INDUCTOR CHIP 0UH Q901 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)
FB784 1-414-633-22 INDUCTOR CHIP 0UH Q902 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3)
FB785 1-414-633-22 INDUCTOR CHIP 0UH Q903 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)
Q904 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3)
FB787 1-414-633-22 INDUCTOR CHIP 0UH < RESISTOR >
FB789 1-500-284-21 INDUCTOR CHIP 0UH R703 1-216-864-11 METAL CHIP 0 5% 1/16W
R710 1-216-814-11 METAL CHIP 270 5% 1/16W
FB801 1-414-229-11 INDUCTOR CHIP 0UH R714 1-218-872-11 METAL CHIP 11K 0.5% 1/16W
FB803 1-414-229-11 INDUCTOR CHIP 0UH R715 1-216-847-11 METAL CHIP 150K 5% 1/16W
R716 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
R717 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
R718 1-216-826-11 METAL CHIP 2.7K 5% 1/16W
R719 1-216-826-11 METAL CHIP 2.7K 5% 1/16W
6-16
PK-50 (FD90)
R720 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R913 1-216-844-11 METAL CHIP 82K 5% 1/16W
R721 1-216-829-11 METAL CHIP 4.7K 5% 1/16W (CA)
R723 1-216-831-11 METAL CHIP 6.8K 5% 1/16W (SH)
R724 1-216-839-11 METAL CHIP 33K 5% 1/16W R916 1-216-833-91 RES-CHIP 10K 5% 1/16W
R917 1-216-857-11 METAL CHIP 1M 5% 1/16W
R725 1-216-839-11 METAL CHIP 33K 5% 1/16W (SH)
R726 1-216-833-91 RES-CHIP 10K 5% 1/16W R918 1-216-864-11 METAL CHIP 0 5% 1/16W
R729 1-216-864-11 METAL CHIP 0 5% 1/16W
R782 1-216-821-11 METAL CHIP 1K 5% 1/16W R919 1-216-857-11 METAL CHIP 1M 5% 1/16W
R787 1-216-821-11 METAL CHIP 1K 5% 1/16W R920 1-216-837-11 METAL CHIP 22K 5% 1/16W
R921 1-216-843-11 METAL CHIP 68K 5% 1/16W
R803 1-216-864-11 METAL CHIP 0 5% 1/16W R922 1-216-843-11 METAL CHIP 68K 5% 1/16W
R809 1-216-834-11 METAL CHIP 12K 5% 1/16W
R812 1-216-841-11 METAL CHIP 47K 5% 1/16W R925 1-218-887-11 METAL CHIP 47K 0.5% 1/16W
R813 1-216-835-11 METAL CHIP 15K 5% 1/16W (CA)
R925 1-218-891-11 METAL CHIP 68K 0.5% 1/16W
R814 1-216-839-11 METAL CHIP 33K 5% 1/16W (SH)
R817 1-216-830-11 METAL CHIP 5.6K 5% 1/16W R927 1-218-885-11 METAL CHIP 39K 0.5% 1/16W
(CA) (CA)
R817 1-216-834-11 METAL CHIP 12K 5% 1/16W R927 1-218-883-11 METAL CHIP 33K 0.5% 1/16W
(SH) (SH)
R818 1-216-840-11 METAL CHIP 39K 5% 1/16W R928 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R820 1-216-845-11 METAL CHIP 100K 5% 1/16W
R929 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R853 1-218-867-11 METAL CHIP 6.8K 0.5% 1/16W R931 1-216-864-11 METAL CHIP 0 5% 1/16W
R854 1-218-881-11 METAL CHIP 27K 0.5% 1/16W (CA)
R855 1-218-897-11 METAL CHIP 120K 0.5% 1/16W R932 1-216-845-11 METAL CHIP 100K 5% 1/16W
R857 1-216-837-11 METAL CHIP 22K 5% 1/16W R934 1-216-864-11 METAL CHIP 0 5% 1/16W
R858 1-216-818-11 METAL CHIP 560 5% 1/16W (SH)
R860 1-218-871-11 METAL CHIP 10K 0.5% 1/16W R936 1-216-845-11 METAL CHIP 100K 5% 1/16W
(CA)
R863 1-216-823-11 METAL CHIP 1.5K 5% 1/16W (CA)
R864 1-216-841-11 METAL CHIP 47K 5% 1/16W
R944 1-218-883-11 METAL CHIP 33K 0.5% 1/16W
R867 1-216-055-00 METAL CHIP 1.8K 5% 1/10W (SH)
R869 1-216-845-11 METAL CHIP 100K 5% 1/16W (CA)
R870 1-216-831-11 METAL CHIP 6.8K 5% 1/16W R945 1-218-879-11 METAL CHIP 22K 0.5% 1/16W
R871 1-216-837-11 METAL CHIP 22K 5% 1/16W (SH)
R872 1-216-817-11 METAL CHIP 470 5% 1/16W R946 1-218-883-11 METAL CHIP 33K 0.5% 1/16W
R873 1-216-810-11 METAL CHIP 120 5% 1/16W (SH)
R901 1-216-864-11 METAL CHIP 0 5% 1/16W R947 1-218-879-11 METAL CHIP 22K 0.5% 1/16W
(CA) (SH)
(CA) (CA)
(SH) (CA)
R950 1-216-864-11 METAL CHIP 0 5% 1/16W
R904 1-216-841-11 METAL CHIP 47K 5% 1/16W (CA)
R905 1-216-841-11 METAL CHIP 47K 5% 1/16W
R908 1-216-864-11 METAL CHIP 0 5% 1/16W
(CA)
R911 1-216-846-11 METAL CHIP 120K 5% 1/16W
R912 1-216-855-11 METAL CHIP 680K 5% 1/16W
6-17
PK-50 (FD90) PK-52 (FD85)
R951 1-216-864-11 METAL CHIP 0 5% 1/16W < SENSOR >
(CA)
R952 1-216-864-11 METAL CHIP 0 5% 1/16W SE701 1-801-868-41 SENSOR, SHOCK
(SH)
R953 1-216-864-11 METAL CHIP 0 5% 1/16W < TRANSFORMER >
(CA)
R954 1-216-864-11 METAL CHIP 0 5% 1/16W 0 T851 1-435-227-11 TRANSFORMER, INVERTER
(SH) **************************************************************
R956 1-216-864-11 METAL CHIP 0 5% 1/16W
(SH) A-7074-418-A PK-52(SC) BOARD, COMPLETE (FD85)(ST)
*************************
R957 1-216-864-11 METAL CHIP 0 5% 1/16W A-7074-419-A PK-52(SN) BOARD, COMPLETE (FD85)(SA)
(SH) *************************
R958 1-216-864-11 METAL CHIP 0 5% 1/16W (REF.NO.;6000 Series)
(SH)
R959 1-216-864-11 METAL CHIP 0 5% 1/16W < BATTERY >
(SH)
R960 1-216-864-11 METAL CHIP 0 5% 1/16W BT701 1-528-999-11 BATTERY, LITHIUM SECONDARY
(SH)
R961 1-216-864-11 METAL CHIP 0 5% 1/16W < CAPACITOR >
(SH)
C705 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
(CA) C710 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
R963 1-216-864-11 METAL CHIP 0 5% 1/16W C711 1-162-925-11 CERAMIC CHIP 68PF 5% 50V
R964 1-216-864-11 METAL CHIP 0 5% 1/16W
(SH) C852 1-119-751-11 TANTAL. CHIP 22uF 20% 16V
R966 1-216-845-11 METAL CHIP 100K 5% 1/16W C853 1-165-128-11 CERAMIC CHIP 0.22uF 16V
(CA) C854 1-135-149-21 TANTALUM CHIP 2.2uF 20% 10V
R967 1-216-864-11 METAL CHIP 0 5% 1/16W C855 1-164-505-11 CERAMIC CHIP 2.2uF 16V
(CA) C856 1-162-918-11 CERAMIC CHIP 18PF 5% 50V
(SH) C858 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R969 1-216-864-11 METAL CHIP 0 5% 1/16W C859 1-162-920-11 CERAMIC CHIP 27PF 5% 50V
(SH) C861 1-113-682-11 TANTAL. CHIP 33uF 20% 10V
R970 1-216-864-11 METAL CHIP 0 5% 1/16W C862 1-115-156-11 CERAMIC CHIP 1uF 10V
(CA)
(SH) 0 C866 1-131-959-91 CERAMIC CHIP 12PF 10% 3KV
C901 1-107-687-11 TANTAL. CHIP 3.3uF 20% 20V
R973 1-216-805-11 METAL CHIP 47 5% 1/16W
R975 1-216-805-11 METAL CHIP 47 5% 1/16W C905 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V
R976 1-216-805-11 METAL CHIP 47 5% 1/16W (SA)
(CA)
R977 1-216-829-11 METAL CHIP 4.7K 5% 1/16W C907 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
< SWITCH > C909 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
S701 1-771-688-21 SWITCH, TACTILE (MENU) C911 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
S702 1-771-138-61 SWITCH, KEY BOARD (DISPLAY)
S703 1-572-467-21 SWITCH, PUSH (1 KEY) (POWER ) C912 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V
S704 1-771-138-61 SWITCH, KEY BOARD (VOLUME+) C913 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V
S705 1-771-138-61 SWITCH, KEY BOARD (FLASH) C914 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V
S706 1-771-138-61 SWITCH, KEY BOARD (VOLUME-) C916 1-164-505-11 CERAMIC CHIP 2.2uF 16V
S707 1-771-138-61 SWITCH, KEY BOARD (PROGRAM AE)
S708 1-572-467-21 SWITCH, PUSH (1 KEY)(PLAY/STILL/MOVIE)
S709 1-762-741-11 SWITCH, SLIDE (LCD BACKLIGHT)
S710 1-572-467-21 SWITCH, PUSH (1 KEY)(PLAY/STILL/MOVIE)
S711 1-771-138-61 SWITCH, KEY BOARD (MACRO)

Note : Note :
6-18
PK-52 (FD85)
C917 1-107-686-11 TANTAL. CHIP 4.7uF 20% 16V < COIL >
C918 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
C919 1-107-687-11 TANTAL, CHIP 3.3uF 20% 20V L702 1-414-756-11 INDUCTOR 47uH
C920 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V L851 1-414-753-91 INDUCTOR 4.7uH
C921 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V L852 1-424-674-11 INDUCTOR 22uH
L853 1-419-387-21 INDUCTOR 100uH
C925 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V L903 1-414-756-11 INDUCTOR 47uH
C926 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V L904 1-412-949-21 INDUCTOR 6.8uH
C927 1-162-924-11 CERAMIC CHIP 56PF 5% 50V < TRANSISTOR >

C929 1-165-128-11 CERAMIC CHIP 0.22uF 10% 16V Q851 8-729-045-75 TRANSISTOR RN1107F(TPL3)
(ST) Q852 8-729-042-59 TRANSISTOR UN9112J-(K8).SO
C931 1-109-982-11 CERAMIC CHIP 1uF 10% 10V Q853 8-729-037-74 TRANSISTOR UN9213J-(K8).SO
(ST) Q854 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO
C932 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V Q855 8-729-037-74 TRANSISTOR UN9213J-(K8).SO
< CONNECTOR > Q856 8-729-823-84 TRANSISTOR FP102-TL

Q857 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO
CN701 1-778-637-21 CONNECTOR, FFC/FPC (ZIF) 50P Q858 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO
CN702 1-784-342-11 HOUSING, CONNECTOR 2P Q859 8-729-037-74 TRANSISTOR UN9213J-(K8).SO
CN851 1-691-358-21 CONNECTOR, FFC/FPC (ZIF) 20P Q860 8-729-039-43 TRANSISTOR FP216-TL
CN901 1-691-388-11 CONNECTOR, FFC/FPC 24P
Q861 8-729-042-59 TRANSISTOR UN9112J-(K8).SO
< DIODE > Q901 8-729-037-74 TRANSISTOR UN9213J-(K8).SO (SA)
Q902 8-729-046-75 TRANSISTOR SI2301DS-T1 (SA)
D701 8-719-061-81 DIODE TLYU1002(TPX1,SONY) Q903 8-729-427-74 TRANSISTOR XP4601-TXE
D702 8-719-061-81 DIODE TLYU1002(TPX1,SONY) Q904 8-729-427-74 TRANSISTOR XP4601-TXE
D703 8-719-064-05 DIODE TLGU1002(TPX1,SONY)
D785 8-719-073-01 DIODE MA111-(K8).S0 Q905 8-729-427-74 TRANSISTOR XP4601-TXE
D786 8-719-045-87 DIODE MA4Z082WA-(TX).SO Q908 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3)(ST)
D787 8-719-045-87 DIODE MA4Z082WA-(TX).SO < RESISTOR >

D853 8-719-073-01 DIODE MA111-(K8).S0 R703 1-216-864-11 METAL CHIP 0 5% 1/16W
D904 8-713-102-80 DIODE 1T369-01-T8A R705 1-216-819-11 METAL CHIP 680 5% 1/16W
D906 8-719-050-42 DIODE RD3.3UM-T1B (ST) R710 1-216-814-11 METAL CHIP 270 5% 1/16W
R713 1-216-819-11 METAL CHIP 680 5% 1/16W
< FERRITE BEAD > R714 1-218-872-11 METAL CHIP 11K 0.5% 1/16W
FB787 1-414-633-22 INDUCTOR CHIP 0UH R715 1-216-847-11 METAL CHIP 150K 5% 1/16W
FB788 1-414-228-11 INDUCTOR CHIP 0UH R716 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
R723 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
< IC > R724 1-216-839-11 METAL CHIP 33K 5% 1/16W
IC702 8-759-572-54 IC TA6009FN(EL) R725 1-216-839-11 METAL CHIP 33K 5% 1/16W

IC851 8-759-521-35 IC TL5001CDR R726 1-216-833-91 RES-CHIP 10K 5% 1/16W
IC852 8-759-075-70 IC TA75S393F-TE85R R729 1-216-864-11 METAL CHIP 0 5% 1/16W
IC901 8-759-524-98 IC CXA8116R-T4 R782 1-216-821-11 METAL CHIP 1K 5% 1/16W
IC902 8-759-364-05 IC MB40D001PFV-G-BND-ER R787 1-216-821-11 METAL CHIP 1K 5% 1/16W
IC903 8-759-327-01 IC NJM062V(TE2) R853 1-218-867-11 METAL CHIP 6.8K 0.5% 1/16W
IC904 8-759-677-84 IC LC12017-52T-TE-B (SA) R854 1-218-881-11 METAL CHIP 27K 0.5% 1/16W
IC904 8-752-405-01 IC CXD3510R (ST) R855 1-218-897-11 METAL CHIP 120K 0.5% 1/16W
R856 1-216-818-11 METAL CHIP 560 5% 1/16W
< JACK > R857 1-216-837-11 METAL CHIP 22K 5% 1/16W
J781 1-695-514-31 JACK (SMALL TYPE) 1P R858 1-216-818-11 METAL CHIP 560 5% 1/16W
(AUDIO(MONO)VIDEO OUT) R859 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R860 1-218-871-11 METAL CHIP 10K 0.5% 1/16W
R861 1-218-853-11 METAL CHIP 1.8K 0.5% 1/16W
R862 1-218-859-11 METAL CHIP 3.3K 0.5% 1/16W
6-19
PK-52 (FD85)
R867 1-216-055-00 METAL CHIP 1.8K 5% 1/10W (ST)
R944 1-216-845-11 METAL CHIP 100K 5% 1/16W
R868 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R869 1-216-845-11 METAL CHIP 100K 5% 1/16W
R871 1-216-837-11 METAL CHIP 22K 5% 1/16W (SA)
(ST)
R876 1-216-843-11 METAL CHIP 68K 5% 1/16W (SA)
(SA) (ST)
R903 1-216-845-11 METAL CHIP 100K 5% 1/16W
(SA) R949 1-216-841-11 METAL CHIP 47K 5% 1/16W
R950 1-216-843-11 METAL CHIP 68K 5% 1/16W
R904 1-216-845-11 METAL CHIP 100K 5% 1/16W R951 1-216-833-91 RES-CHIP 10K 5% 1/16W
(SA) R953 1-216-833-91 RES-CHIP 10K 5% 1/16W
R906 1-216-809-11 METAL CHIP 100 5% 1/16W (ST)
R907 1-216-809-11 METAL CHIP 100 5% 1/16W
R956 1-216-839-11 METAL CHIP 33K 5% 1/16W
R911 1-216-845-11 METAL CHIP 100K 5% 1/16W (ST)
R912 1-216-295-91 SHORT 0 (ST) R959 1-216-864-11 METAL CHIP 0 5% 1/16W
R913 1-216-837-11 METAL CHIP 22K 5% 1/16W (SA)
R915 1-216-841-11 METAL CHIP 47K 5% 1/16W (ST)
R917 1-216-841-11 METAL CHIP 47K 5% 1/16W (ST)
R963 1-216-864-11 METAL CHIP 0 5% 1/16W
(SA)
(ST) (ST)
(ST) (ST)
R923 1-216-840-11 METAL CHIP 39K 5% 1/16W R967 1-216-831-91 RES-CHIP 6.8K 5% 1/16W
(SA) (SA)
(SA)
(SA) (SA)
R925 1-216-837-11 METAL CHIP 22K 5% 1/16W
(ST) R970 1-216-864-11 METAL CHIP 0 5% 1/16W
R926 1-216-829-11 METAL CHIP 4.7K 5% 1/16W (SA)
R928 1-216-841-11 METAL CHIP 47K 5% 1/16W (SA)
R972 1-216-864-11 METAL CHIP 0 5% 1/16W
R929 1-216-845-11 METAL CHIP 100K 5% 1/16W (SA)
R930 1-216-833-91 RES-CHIP 10K 5% 1/16W R973 1-216-831-91 RES-CHIP 6.8K 5% 1/16W
R931 1-216-809-11 METAL CHIP 100 5% 1/16W (SA)
R933 1-216-809-11 METAL CHIP 100 5% 1/16W (ST)
R935 1-216-857-11 METAL CHIP 1M 5% 1/16W R975 1-216-853-11 METAL CHIP 470K 5% 1/16W
R936 1-216-840-11 METAL CHIP 39K 5% 1/16W (ST)
R937 1-216-833-91 RES-CHIP 10K 5% 1/16W R976 1-216-839-11 METAL CHIP 33K 5% 1/16W
R938 1-216-843-11 METAL CHIP 68K 5% 1/16W (ST)
(SA) R977 1-216-842-11 METAL CHIP 56K 5% 1/16W
R938 1-216-841-11 METAL CHIP 47K 5% 1/16W (ST)
(ST) R979 1-216-864-11 METAL CHIP 0 5% 1/16W
(ST)
R980 1-216-864-11 METAL CHIP 0 5% 1/16W
(ST)
6-20
PK-52 (FD85)
R981 1-216-864-11 METAL CHIP 0 5% 1/16W M903 3-709-499-01 METER, ND (FD90)
(SA) M904 3-709-573-01 MOTOR UNIT, FOCUS (FD85)
R982 1-216-864-11 METAL CHIP 0 5% 1/16W M905 3-709-574-01 MOTOR UNIT, ZOOM (FD85)
R984 1-218-887-11 METAL CHIP 47K 0.5% 1/16W MIC901 1-542-428-11 MICROPHONE UNIT
R985 1-218-893-11 METAL CHIP 82K 0.5% 1/16W **************************************************************
(SA)
R985 1-218-887-11 METAL CHIP 47K 0.5% 1/16W ACCESSORIES
(ST) ************
0 1-475-599-11 ADAPTOR, AC
R987 1-216-839-11 METAL CHIP 33K 5% 1/16W (FD85:J,US,CND,AEP,UK,HK,AUS,JE/
(FD90):J,US,CND,AEP,UK,HK,AUS,JE)
< SWITCH > 0 1-475-599-71 ADAPTOR, AC (FD90:KR)
0 1-569-007-11 ADAPTOR, CONVERSION 2P
S701 1-771-688-21 SWITCH, TACTILE (MENU) (FD85:E,JE,BR/FD90:E,JE)
S702 1-771-138-61 SWITCH, KEY BOARD (DISPLAY) 0 1-569-008-21 ADAPTOR, CONVERSION 2P
S703 1-572-467-21 SWITCH, PUSH (1 KEY) (POWER ) (FD85:E,BR/FD90:E)
S704 1-771-138-61 SWITCH, KEY BOARD (VOLUME+) 0 1-696-819-11 CORD,POWER (FD85:AUS/FD90:AUS)
S705 1-771-138-61 SWITCH, KEY BOARD (FLASH)
0 1-769-608-11 CORD,POWER (FD85:AEP,E,BR/FD90:AEP,E)
S706 1-771-138-61 SWITCH, KEY BOARD (VOLUME-) 0 1-776-985-11 CORD,POWER (FD90:KR)
S707 1-771-138-61 SWITCH, KEY BOARD (PROGRAM AE) 0 1-782-476-11 CORD,POWER (FD85:CN/(FD90):CN)
S708 1-572-467-21 SWITCH, PUSH (1 KEY) (PLAY/STILL/MOVIE) 0 1-783-374-11 CORD,POWER (FD85:UK,HK/FD90:UK,HK)
S709 1-762-741-11 SWITCH, SLIDE (LCD BACKLIGHT) 1-783-738-11 CORD,CONNECTION(1.5m)(AV COBLE)
S710 1-572-467-21 SWITCH, PUSH (1 KEY) (PLAY/STILL/MOVIE)
0 1-790-073-11 CORD,POWER 2P (FD85:J,JE/FD90:J,JE)
S711 1-771-138-61 SWITCH, KEY BOARD (FOCUS) 0 1-790-107-22 CORD,POWER (FD85:US,CND/FD90:US,CND)
3-055-746-01 SOFT(CS), BUNDLE(FD85:US/FD90:US)
< SENSOR > 3-060-716-01 SOFT(2000), BUNDLE
(FD85:J,CND,AEP,UK,E,HK,AUS,CN,JE/
SE701 1-801-868-41 SENSOR, SHOCK FD90:J,CND,AEP,UK,E,HK,AUS,CN,JE,KR)
3-060-831-01 MANUAL, INSTRUCTION (JAPANESE)
< TRANSFORMER > (FD85:J/FD90:J)
0 T851 1-435-227-11 TRANSFORMER, INVERTER 3-060-831-11 MANUAL, INSTRUCTION (ENGLISH)

************************************************************** (FD85:US,CND,AEP,UK,E,HK,AUS,CN,JE/
FD90:US,CND,AEP,UK,E,HK,AUS,CN,JE)
MISCELLANEOUS 3-060-831-21 MANUAL, INSTRUCTION (FRENCH/GERMAN)
************** (FD85:CND,AEP,JE/FD90:CND,AEP,JE)
3-060-831-31 MANUAL, INSTRUCTION
6 1-772-563-11 DRIVE, FLOPPY DISK (SPANISH/PORTUGUESE)
9 1-960-461-11 HARNESS (FU-052) (FD85:AEP,E,JE/FD90:AEP,E,JE)
10 1-960-460-11 HARNESS (FU-051) 3-060-831-41 MANUAL, INSTRUCTION (ITALIAN/DUTCH)
11 1-794-045-21 CONNECTOR, DC-IN (FD85:AEP/FD90:AEP)
14 1-418-995-11 FLASH UNIT 3-060-831-51 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE/SIMPLIFIED CHINESE)
64 1-694-297-21 TERMINAL BOARD, BATTERY (FD85:E,HK,CN,JE/FD90:E,HK,CN,JE)
65 1-418-894-11 SWITCH BLOCK, CONTROL
67 1-418-895-11 SWITCH BLOCK, CONTROL (MF 330)(FD90) 3-060-831-61 MANUAL, INSTRUCTION (SWEDISH/RUSSIAN)
122 1-677-897-11 PWB, FP-165 FLEXIBLE (FD85:AEP,JE/FD90:AEP,JE)
151 1-677-903-11 PWB, FP-231 FLEXIBLE (FD85) 3-060-831-71 MANUAL, INSTRUCTION (ARABIC)
(FD85:E/FD90:E)
155 1-758-435-11 FILTER BLOCK, OPTICAL (FD85) 3-060-831-81 MANUAL, INSTRUCTION (KOREAN)
159 1-758-415-11 LENS, ZOOM (VCL-6103WA)(FD85) (FD85:JE/FD90:JE,KR)
162 1-758-475-11 LENS, VIDEO (61JC)(FD90) 3-866-482-01 MANUAL, INSTRUCTION (FD85:J/FD90:J)
163 1-677-898-11 PWB, FP-167 FLEXIBLE (FD90) 3-987-015-01 BELT(S), SHOULDER
167 1-758-322-21 FILTER BLOCK, OPTICAL (FD90)
A-7094-140-A NP-F330 BATTERY PACK (FD85/FD90:US,CND)
0 ND901 1-517-787-21 TUBE, FLUORESCENT,COLD CATHODE A-7094-141-A NP-F330 BATTERY PACK
SP901 1-505-862-41 SPEAKER (2.0 CM) (FD85:BR/FD90:AEP,UK,E,HK,AUS,CN,JE,KR)
LCD901 1-803-860-21 INDICATOR MODULE LIQUID CRYST(FD90)(CA) A-7094-142-A NP-F330 BATTERY PACK (FD90:J)
LCD901 1-803-858-21 INDICATOR MODULE LIQUID CRYST(FD90)(SH) X-3950-660-1 CAP ASSY, LENS
LCD901 1-803-997-21 INDICATOR MODULE, LIQUID CRYST
(FD85)(SA)
LCD901 8-753-050-21 INDICATOR MODULE, LIQUID CRYST

(FD85)(ST)
IC101 A-7031-083-A CCD BLOCK ASSY (CCD Imager)(FD90)
IC201 A-7031-090-A CCD BLOCK ASSY (CCD Imager)(FD85)
M901 3-709-498-01 MOTOR, ZOOM STEPPING (FD90)
Note : Note :
M902 3-709-497-01 MOTOR, FOCUS STEPPING (FD90)
6-21E
〈FOR CAMERA COLOR REPRODUCTION ADJUSTMENT〉
Take a copy of CAMERA COLOR

REPRODUCTION FRAME with
a clear sheet for use.
✂
— 137 —
MVC-FD85/FD90
Sony Corporation
2000C1649-1
9-929-813-31 Personal VIDEO Products Company Printed in Japan © 2000.3
— 138 — Published by Safety & Service Engineering Dept.

Service Manual: MVC-FD85/FD90

Uploaded by

Copyright:

Available Formats

Service Manual: MVC-FD85/FD90

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: MVC-FD85/FD90

Uploaded by

Copyright:

Available Formats

MVC-FD85/FD90

SERVICE MANUAL US Model

On the FC-72 board This service manual contains information

The above-described information is shown in service manual Level 3.

DIGITAL STILL CAMERA

SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

After correcting the original service problem, perform the following

• NOT FOR REPAIR

When installing a connector, don't press down at wire of connector.

Cut and remove the part of gilt

[Discharging of the FLASH unit’s charging capacitor]

The charging capacitor of the FLASH unit is charged up to the

Preparing the Short Jig Discharging the Capacitor

Display Code Countermeasure Cause Caution Display During Error

Note: The error code is cleared if rthe battery is removed, except

2-1 . Cabinet (Rear) block assembly

LCD, PK-50/52 board

2-8. Eject button section

2-2. FC-72 board, Floppy disk drive

2-6. DC-IN connector, Microphone UNIT

2-7. Hinge assembly, Battery terminal board

2-3. Lens block assembly

Main (FC-72) board, Lens block assembly

2-9. Focus stepping motor, Zoom stepping motor,

2-10. Focus motor unit, Zoom motor unit

NOTE: Follow the disassembly procedure in the numerical order given.

2-1. CABINET (REAR) BLOCK ASSEMBLY

7 Cabinet (front) block assembly

5 Two screws (M2 × 4),

3 Two screws (M2 × 4), lock ace, p2

6 Cabinet (rear) block assembly

2 Screw (M2 × 4),

q; Flash unit (10p)

qg Floppy disk drive (4 × )

5 Four screws (M2 × 2.5)

Cautions When Handling FDD

1. Correct Way of Holding an FDD 2. Prohibited Items

Do not apply any physical

Wear an earthed wrist strap. Do not hold an FDD by sandwiching

If the FDD is not held correctly,

3 Cabinet (front) assembly

1 Tapping screw (M2 × 5)

2 Lens block assembly

REMOVING THE CD-246 BOARD REMOVING THE CD-248 BOARD

FU-52 harness (9p)

Lens block assembly

1 Two claws 2 Speaker retainer

qs Liquid cryst module indicator

qa Cold cathode fluorescent tube

2 Cold cathode fluorescent tube (20p)

q; Back light retainer

[ LCD, PK-50/52 BOARD CHECK SERVICE POSITION ]

CD-246 board (MVC-FD90)

Liquid cryst module indicator (24p)

PK-52 board (MVC-FD85)

Cold cathode fluorescent tube (20p)

6 FU-140 board (MVC-FD90)

4 Control switch block (6p)

Short jig (see page 5)