Service Manual: LCD Colour Television

TopPage
LC-52DH77E/RU/S
SERVICE MANUAL
No. S49Z2LC52D77E
LCD COLOUR TELEVISION
MODELS LC-52DH77E/RU/S
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION CHAPTER 5. BLOCK DIAGRAM/WIRING DIAGRAM
IMPORTANT SERVICE SAFETY PRE- [1] MAIN BLOCK DIAGRAM...............................5-1
CAUTION ............................................................i [2] SYSTEM BLOCK DIAGRAM .........................5-2
Precautions for using lead-free solder ...............ii [3] OVERALL WIRING DIAGRAM ......................5-3
End of life disposal ............................................ iii
CHAPTER 6. PRINTED WIRING BOARD
CHAPTER 1. OPERATION MANUAL [1] MAIN UNIT PRINTED WIRING BOARD........6-1
[1] SPECIFICATIONS ......................................... 1-1 [2] LED UNIT PRINTED WIRING BOARD .........6-5
[2] OPERATION MANUAL .................................. 1-2 [3] KEY UNIT PRINTED WIRING BOARD .........6-6
[3] DIMENSIONS ................................................ 1-7
CHAPTER 7. SCHEMATIC DIAGRAM
CHAPTER 2. REMOVING OF MAJOR PARTS [1] DESCRIPTION OF SCHEMATIC DIA-
[1] REMOVING OF MAJOR PARTS ................... 2-1 GRAM............................................................7-1
[2] SCHEMATIC DIAGRAM ................................7-2
CHAPTER 3. ADJUSTMENT PROCEDURE
[1] ADJUSTMENT PROCEDURE ....................... 3-1 Parts Guide
CHAPTER 4. TROUBLESHOOTING TABLE

[1] TROUBLESHOOTING TABLE....................... 4-1
[2] LED flashing specification at the time of the
error.............................................................. 4-14
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for

after sales service only.
The contents are subject to change without notice.
Downloaded from www.Manualslib.com manuals search engine
LC-52DH77E/RU/S
LC52DH77E
SAFETY PRECAUTION Service Manual
IMPORTANT SERVICE SAFETY PRECAUTION

Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
WARNING • Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
1. For continued safety, no modification of any circuit should be
attempted. • Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
2. Disconnect AC power before servicing.
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
CAUTION:
reversed. (If necessary, a nonpolarized adaptor plug must be used
FOR CONTINUED PROTECTION AGAINST A only for the purpose of completing these checks.)
RISK OF FIRE REPLACE ONLY WITH SAME Any reading of 1.05 V peak (this corresponds to 0.7 mA peak AC.)
TYPE FUSE. or more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
F7000, F7001 (4A/250V)
DVM
AC SCALE
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard) 1.5k ohm
10W
Before returning the receiver to the user, perform the following
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver. 0.15 µF
TEST PROBE
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner. TO EXPOSED CONNECT TO
METAL PARTS KNOWN EARTH
• Plug the AC cord directly into a 220~240 volt AC outlet. GROUND
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by “ ” and shaded areas in the Replacement Parts
List and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
LC-52DH77E/RU/S
Precautions for using lead-free solder
Employing lead-free solder

• “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
LFa L F a/a
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Using lead-free wire solder

• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Part No. Description Code

ZHNDAi123250E J φ0.3mm 250g (1roll) BL
ZHNDAi126500E J φ0.6mm 500g (1roll) BK
ZHNDAi12801KE J φ1.0mm 1kg (1roll) BM
ii
LC-52DH77E/RU/S
End of life disposal
End of life disposal

A. Information on Disposal for Users (private households)
1. In the European Union

Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires
proper treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used
electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local
Attention: Your product retailer may also take back your old product free of charge if you purchase a similar new one.
is marked with this
*) Please contact your local authority for further details.
symbol. It means that
used electrical and
electronic products If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately
should not be mixed beforehand according to local requirements.
with general household
waste. There is a By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery
separate collection and recycling and thus prevent potential negative effects on the environment and human health which could otherwise
system for these
arise due to inappropriate waste handling.
products.
2. In other Countries outside the EU

If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union

If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for
the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local
collection facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used
products.
2. In other Countries outside the EU

If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
The battery supplied with this product contains traces of Lead.
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste!
There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with
legislation. Please contact your local authority for details on the collection and recycling schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct method of disposal of the used battery.
iii
LC-52DH77E/RU/S
CHAPTER 1. OPERATION MANUAL
LC52DH77E
Service Manual
[1] SPECIFICATIONS
52" LCD COLOUR TV,

Item
Model: LC-52DH77E, LC-52DH77RU, LC-52DH77S
LCD panel 52" Advanced Super View & BLACK TFT LCD
Resolution 2,073,600 pixels (1,920 1,080)
Video Colour System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV Function TV-Standard Analogue CCIR (B/G, I, D/K, L/L')
Digital DVB-T (2K/8K OFDM)
Receiving VHF/UHF E2-E69 ch, F2-F10 ch, I21-I69 ch, IR A-IR J ch (Digital: IR A ch-E69 ch)
Channel
CATV Hyper-band, S1-S41 ch
TV-Tuning System Auto Preset 999 ch: non-Nordic / 9999 ch: Nordic (ATV: 99 ch), Auto Label, Auto Sort
STEREO/BILINGUAL NICAM/A2
Brightness 450 cd/m 2
Viewing angles H: 176°, V: 176°
Audio amplifier 10 W 2
Speaker (40 mm 110 mm) 2
Terminals Antenna UHF/VHF 75 Ω Din type (Analogue & Digital)
RS-232C D-Sub 9 pin male connector
EXT1 SCART (AV input, Y/C input, RGB input, TV output)
EXT2 SCART (AV input/monitor output, Y/C input, AV Link)
EXT3 COMPONENT IN: Y/PB(CB)/PR(CR), RCA pin (AUDIO R/L)
EXT4 15 pin mini D-sub, Ø 3.5 mm jack*
HDMI1 (EXT5) HDMI
HDMI2 (EXT6) HDMI, Ø 3.5 mm jack*
HDMI3 (EXT7) HDMI
EXT8 RCA pin (AV input)
USB USB
DIGITAL AUDIO OUTPUT Optical S/PDIF Digital audio output
C. I. (Common Interface) EN50221, R206001
OUTPUT RCA pin (AUDIO R/L)
Headphones Ø 3.5 mm jack (Audio output)
OSD language Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian,
Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slovene, Spanish,
Swedish, Turkish, Ukrainian
Power Requirement AC 220-240 V, 50 Hz
Power Consumption (Method IEC62087) 252 W (0.2 W Standby)
Weight 23.5 kg (Without stand), 27.0 kg (With stand)
Operating temperature 0 °C to +40 °C
* The HDMI2 and EXT4 terminals can both use the same audio input terminal.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
NOTE
Refer to the inside back cover for dimensional drawings.
Optional accessory
The listed optional accessories are available for this LCD No. Part name Part number
colour TV. Please purchase them at your nearest shop.
Additional optional accessories may be available in the near Wall mount bracket
future. When purchasing, please read the newest catalogue for 1 (LC-52DH77E, LC-52DH77RU, AN-52AG4
compatibility and check the availability. LC-52DH77S)
1–1
LC-52DH77E/RU/S
[2] OPERATION MANUAL
Remote control unit

1 (Standby/On) 13 END
Exit the “MENU” screen.
2 Buttons for useful operations 1 14 R/G/Y/B (Colour) buttons
(Teletext) 2 The coloured buttons are
ATV: Display analogue teletext. correspondingly used to select the
coloured items on the screen (e.g.
DTV: Select MHEG-5 and teletext for
EPG, MHEG-5, Teletext).
DTV. 3
15 (INPUT SOURCE)
(Reveal hidden Teletext) Select an input source.
15 16 EPG
4
(Subtitle) 5 16 DTV: Display the EPG screen.
Switch subtitle languages on/off. 6 17
17 RADIO
7 18 DTV: Switch between Radio and
(Freeze/Hold)
Press to freeze a moving image on 8 19 Data mode.
the screen. 9 20 • When only data broadcasting (no
Teletext: Stop updating teletext 10 21 radio broadcasting) is transmitted
pages automatically or release the by DVB, the radio broadcasting
hold mode. 11 22 will be skipped.
(Subpage) 18 P. INFO
12 Press to display programme
information which is transmitted
(Top/Bottom/Full) 13 23 through digital video broadcasting in
Set the area of magnification in the upper left corner of the screen
teletext mode. 14 (DTV only).
3 0–9 numeric buttons 19 P /
Set the channel. Select the TV channel.
Enter desired numbers.
Set the page in teletext mode. 24 20 (Display information)
• When the five Nordic countries Press to display the station
(Sweden, Norway, Finland, 25 information (channel number, signal,
Denmark, or Iceland) are selected etc.) in the upper right corner of the
in the country setting from “Auto screen.
Installation”, DTV services are 21 ECO (Standard/Advanced/Off)
four digits. When another country is Select “Energy Save” setting.
selected, DTV services are three digits.
22 MENU
4 (Flashback) “MENU” screen on/off.
Press to return to the previously 23 (Return)
selected channel or external input. Return to the previous “MENU”
5 DTV screen.
Press to access digital TV mode. 24 SLEEP
6 ATV Press to schedule a time for the TV
Press to access conventional to automatically standby.
analogue TV mode. 25 AQUOS LINK buttons
7 (Sound mode) If external equipment such as a
Select a sound multiplex mode. AQUOS BD Player is connected via
HDMI cables and is AQUOS LINK
8 +/- (Volume) compatible, you can use these
Increase/decrease TV volume. AQUOS LINK buttons.
9 (Mute)
TV sound on/off.
12 / / / (Cursor)
10 (WIDE MODE) Select a desired item on the setting
Select a wide mode. screen.
OK
11 AV MODE Execute a command within the
Select a video setting. “MENU” screen.
ATV/DTV: Display the programme
list when no other “MENU” screen is
running.
1–2
LC-52DH77E/RU/S
TV (Front view)
Remote control sensor OPC indicator
OPC sensor (Standby/On) indicator
TV (Rear view)
16
11
2 3
4 5 6
12
13
* The terminal layout may differ depending
on the model.
14
(Power) button
15
MENU button
7 8 9 10
(INPUT SOURCE)
WARNING button
• Excessive sound pressure from earphones and headphones can cause hearing loss. P /
• Do not set the volume at a high level. Hearing experts advise against extended listening at
Programme (channel)
high volume levels.
buttons
1 EXT4 (ANALOGUE RGB/AUDIO) 7 Antenna terminal +/ Volume
terminals* 8 RS-232C terminal buttons
2 HDMI1 (HDMI) terminal 9 EXT1 (RGB) terminal
3 HDMI2 (HDMI/AUDIO) terminals* 10 EXT2 (AV) terminal
4 EXT3 (COMPONENT/AUDIO) 11 COMMON INTERFACE slot
terminals 12 EXT8 terminals
* The HDMI2 and EXT4 terminals
5 OUTPUT (AUDIO) terminals 13 HDMI3 (HDMI) terminal
can both use the same audio input
6 DIGITAL AUDIO OUTPUT terminal 14 USB terminal
terminal. However, the proper item
15 Headphones
must be selected in the “PC Audio
16 AC INPUT terminal
Select” menu.
1–3
LC-52DH77E/RU/S
Attaching the stand unit

• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work, spread cushioning over the surface on which you will be laying the TV. This will prevent it from being
damaged.
CAUTION
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
1 Confirm that there are eight screws (four short 3 Inserting the stand.
screws and four long screws) with the stand unit. 1 Insert the stand into the openings on the
bottom of the TV (Hold the stand so it will
not drop from the edge of the base area).
2 Insert and tighten the four short screws into
2 Attach the supporting post for the stand unit the four holes on the rear of the TV.
onto the base using the four long screws with Soft cushion
the hex key (supplied) as shown. Hex key
Hex key Short screw 2 2
Long screw
1
1
Supporting NOTE
post • To detach the stand unit, perform the steps in reverse
order.
1–4
LC-52DH77E/RU/S
Inserting the batteries

Before using the TV for the first time, insert two supplied “AAA” size zinc-carbon batteries. When the batteries
become depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
1 Open the battery cover.
2 Insert two supplied “AAA” size zinc-carbon
batteries.
• Place batteries with their terminals corresponding to the
(+) and (-) indications in the battery compartment.
3 Close the battery cover.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you
find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
• When replacing the batteries, use zinc-carbon batteries instead of alkaline ones.
Note on disposing batteries:

The batteries provided contain no harmful materials such as cadmium, lead or mercury.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household
rubbish. Deposit any used batteries free of charge into the designated collection containers set up at commercial
businesses.
Using the remote control unit

Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control
unit and sensor may prevent proper operation.
5m
30° 30° Remote control sensor
Cautions regarding the remote control unit

• Do not expose the remote control unit to shock. In addition, do not expose the
remote control unit to liquids, and do not place in an area with high humidity.
• Do not install or place the remote control unit under direct sunlight. The heat
may cause deformation of the unit.
• The remote control unit may not work properly if the remote control sensor of
the TV is under direct sunlight or strong lighting. In such cases, change the
angle of the lighting or the TV, or operate the remote control unit closer to the
remote control sensor.
1–5
LC-52DH77E/RU/S
Troubleshooting
Problem Possible Solution
• No power. • Check if you pressed on the remote control unit.
If the indicator on the TV lights up red, press .
• Is the AC cord disconnected?
• Check if you pressed on the TV.
• The TV cannot be operated. • External influences such as lightning, static electricity, etc., may cause improper operation. In this
case, operate the TV after first turning off the power, or unplugging the AC cord and re-plugging
it in after one or two minutes.
• Remote control unit does not operate. • Are batteries inserted with polarity (+, -) aligned?
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminating to the remote control sensor?
• Picture is cut off. • Is the image position correct?
• Are screen mode adjustments (WIDE MODE) such as picture size made correctly?
• Strange colour, light colour, or dark • Adjust the picture tone.

colour, or colour misalignment. • Is the room too bright? The picture may look dark in a room that is too bright.
• Check the “Colour System” setting.
• Power is suddenly turned off. • The TV’s internal temperature has increased.
Remove any objects blocking the vent or clean.
• Is the “Sleep Timer” set? Select “Off” from the “Sleep Timer” menu.
• Is “No Signal Off” or “No Operation Off” activated?
• No picture. • Are connections to external equipment correct?
• Is the input signal type selected correctly after connection?
• Is the correct input source selected?
• Is a non-compatible signal being input?
• Is the picture adjustment correct?
• Is the antenna connected properly?
• Is “On” selected in “Audio Only”?
• No sound. • Is the volume too low?
• Make sure that headphones are not connected.
• Check if you pressed on the remote control unit.
• Is the proper item selected in the “PC Audio Select” menu when connecting devices to the
HDMI2 terminal or the EXT4 terminal?
• The TV sometimes makes a cracking • This is not a malfunction. This happens when the cabinet slightly expands and contracts
sound. according to changes in temperature. This does not affect the TV’s performance.
Cautions regarding use in high and low temperature environments

• When the TV is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the TV will recover when the temperature returns to normal.
• Do not leave the TV in a hot or cold location. Also, do not leave the TV in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: +5 °C to +35 °C.
Information on the software license for this product

Software composition
The software included in this product is comprised of various software components whose individual copyrights are held by
SHARP or by third parties.
Software developed by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that were developed
or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant
laws. This product also makes use of freely distributed software and software components whose copyrights are held by
third parties. These include software components covered by a GNU General Public License (hereafter GPL), a GNU Lesser
General Public License (hereafter LGPL) or other license agreement.
Obtaining source code
Some of the open source software licensors require the distributor to provide the source code with the executable software
components. GPL and LGPL include similar requirements. For information on obtaining the source code for the open source
software and for obtaining the GPL, LGPL, and other license agreement information, visit the following website:
http://www.sharp-eu.com/gpl/
We are unable to answer any questions about the source code for the open source software. The source code for the
software components whose copyrights are held by SHARP is not distributed.
Acknowledgements
The following open source software components are included in this product:
• linux kernel • busy box • uClibc • zlib • libpng • libjpeg
1–6
LC-52DH77E/RU/S
[3] DIMENSIONS
1254.0
Unit: mm
1157.0
651.0
863.9
815.9
485.5
527.6
48.0
400.0 118.0 111.7

145.0
400.0
325.0
10°
10°
1–7
LC-52DH77E/RU/S
CHAPTER 2. REMOVING OF MAJOR PARTS
LC52DH77E
Service Manual
[1] REMOVING OF MAJOR PARTS

1. Removing of Stand Unit and Back Cabinet Ass’y.
1. Remove the 4 lock screws 1 and detach the Stand Unit.
2. Remove the 4 lock screws 2 , 1 lock screw 3 , 11 lock screws 4 and detach the Back Cabinet Ass’y.
Back Cabinet Ass'y
Front Cabinet Ass'y
Stand Unit
2–1
LC-52DH77E/RU/S
2. Removing of Bottom Cover, Speaker (L/R), Control Cover Ass’y, KEY Unit and LED Unit.
1. Disconnect all the connectors from all the PWBs.
2. Remove the Bottom Cover.
3. Remove the Speaker (L) 1 , (R) 2 .

4. Remove the Control Cover Ass’y.
5. Remove the KEY Unit.
6. Remove the LED Unit.
Control Cover Ass'y
[KM]
[RA]
[KM] [SP]
KEY Unit
[RA]
LED Unit Bottom Cover
[SP] [SP]
2 Speaker (R) 1 Speaker (L)
2–2
LC-52DH77E/RU/S
3. Removing of Side AV Cover Ass’y and Full Shield.
1. Remove the 1 lock screw 1 , 2 lock screws 2 and detach the Side AV Cover Ass’y.
2. Remove the 2 lock screws 3 , 4 lock screws 4 , 1 lock screw 5 , 5 lock screws 6 and detach the Full Shield.
2 4 6
3
Full Shield
1 4
Side AV
Cover Ass'y
2–3
LC-52DH77E/RU/S
4. Removing of Connectors.
1. Disconnect all the connectors from all the PWBs.
INVERTER Unit
[LB2]
[LA]
[PL] [LW] [LP]
LCD Control Unit
[LB2]
MAIN Unit [LB1]
[LB1] [LA]
[PD]
[PL]
[PD]
[LW]
[LP]
POWER Unit
2–4
LC-52DH77E/RU/S
5. Removing of POWER Unit, MAIN Unit, Corner Lug (A/B/L/S), Vesa Angle Bottom Ass’y, Vesa Angle Top Ass’y
and LCD Panel Module.
1. Remove the 6 lock screws 1 , 3 hooks 2 and detach the POWER Unit.
2. Remove the 7 lock screws 3 and detach the MAIN Unit.
3. Remove the 6 lock screws 4 , 10 lock screws 5 and detach the Corner Lug (A/B/L/S).
4. Remove the 6 lock screws 6 and detach the Vesa Angle Bottom Ass’y.
5. Remove the 4 lock screws 7 and detach the Vesa Angle Top Ass’y.
6. Remove the 6 hooks and detach the LCD Panel Module.
7 7
Vesa Angle Top Ass'y
6 6
Vesa Angle Bottom Ass'y
Corner Lug (B)

5 Corner Lug (A) 5
Corner Lug (A) Corner Lug (B)
Hook Hook
LCD Panel Module
Corner Lug (L) Corner Lug (L)

Hook Hook
Hook
2 Power
PWB
4 5 5 4 Holder
Corner Lug (S)

3 1
MAIN Unit POEWR Unit
2–5
LC-52DH77E/RU/S
6. Removing of LCD Panel Module.
1. Remove the 16 lock screws 1 and detach the Bezel Ass’y 2 .
2. Detach the Lens Sheet 3 and Diffusion Plate 4 .
3. Detach the 2 pieces Lamp Holder Unit 5 , Socket 7 and detach the following 18 pieces Lamp 6 from BL Chassis Ass'y 8 .
8 BL Chassis Ass'y
7 Socket
5 Lamp Holder Unit
1 6 Lamp
5 Lamp Holder Unit
1 4 Diffusion Plate
3 Lens Sheet
2 Bezel Ass'y
2–6
LC-52DH77E/RU/S
CHAPTER 3. ADJUSTMENT PROCEDUREService
LC52DH77E
Manual
[1] ADJUSTMENT PROCEDURE

1. Adjustment method after PWB and/or IC replacement due to repair
The unit is set to the optimum at the time of shipment from the factory. If any value should become improper or any adjustment is necessary due to
the part replacement, make an adjustment according to the following procedure.
1. Procure the following units in order to replace the main unit, IC3302.
MAIN UNIT: DUNTKF190FM01
NOTE: [Caution when replacing ICs in the main unit (IC501, IC1504, IC2002)]
The above ICs are EEPROMs storing the EDID data of PC, HDMI and Monitor microcomputer.
Before replacing the relevant part, procure the following parts in which the data have been rewritten.
IC501 RH-iXC697WJQZS PC
IC2002 RH-iXC786WJN1Q Monitor microcomputer
2. After replacing the LCD panel or LCD control UNIT, check PANEL_SIZE in the following procedure.
1) Enter the process adjustment mode in AVC.
2) Use the cursor keys ( / ) and P keys ( / ) of R/C to select the item [PANEL_SIZE] on the page 16/16.
3) Verify that the panel size is displayed.
4) If the size doesn't match, select the values of the panel size with the VOL (+/-) keys.
5) After selection in Step 4), press the OK key, and it is completed with OK displayed.
3. After replacing the LCD panel or LCD control PWB, adjust the VCOM in the following procedure.
1) Enter the process adjustment mode.
2) Use the cursor keys ( / ) and P ( / ) of R/C to select the item [VCOM ADJ] on the page 10/16.
3) Press the OK key to verify that the adjustment pattern is displayed.
4) Use the +/- keys of VOL of R/C to adjust the flicker in the center of the screen to minimum.
5) When the optimal state is achieved in Step 4, press the OK key to turn the pattern to OFF.
2. Entering and exiting the adjustment process mode

1. Unplug the AC power cord of running TV set to force off the power.
2. While holding down the “VOL (-)” and “INPUT” keys on the set at once, plug in the AC power cord to turn on the power.
The letter “K” appears on the screen.
3. Next, hold down the “VOL (-)” and “P ( )” keys on the set at once.
Multiple lines of blue characters appearing on the screen indicate that the set is now in the adjustment Process mode.
If you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4. To exit the adjustment process mode after the adjustment is done, unplug the AC power cord to force off the power. (When the power is turned off
with the remote controller, once unplug the AC power cord and plug it in again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest the users should know how to enter the adjustment process mode.
If the settings are tampered with in this mode, unrecoverable system damage may result.
3. Remote controller key operation and description of display in adjustment process mode.
1. key operation
Remote controller key Main unit key Function

P( / ) P( / ) Moving an item (line) by one (UP/DOWN)
VOL (+/-) VOL (+/-) Changing a selected item setting (+1/-1)
Cursor ( / ) — Turning a page (PREVIOUS/NEXT)
Cursor (</>) — Changing a selected line setting (+10/-10)
INPUT INPUT Input source switching (toggle switching) (TV→EXT1~8)
OK — Executing a function
RETURN — Returning to a present page
Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
3–1
LC-52DH77E/RU/S
4. Description of display
(1) Present page / number of total pages (4) Inducing display

(3) Present colour system
(2) Input that has been selected now (5) Model name
1/16 INPUT1 AUTO EURO 52E_DH77E
MAIN Version 1.00 (E 2008/**/** 1HDE2)

BOOT Version
Monitor Version 1.0
T-CON /H.264Version
CPLD Version c3
EQ DATA CHECKSUM ROM
LAMP ERROR 0
MONITOR ERR CAUSE 11 11 11 11
NORMAL STANDBY CAUSE 0
ERROR STANDBY CAUSE 1) 0 2) 0 3) 0
0H 0M 0H 0M 0H 0M
4) 0 5) 0
0H 0M 0H 0M
(6) Item name (7) Parameter
No. Description Display specification

(1) Present page/number of total pages 2char/2char Decimal Number mark.
(2) Input that has been selected now TUNER/DTV/INPUT1/INPUT2/INPUT3/INPUT5/INPUT6/INPUT7/INPUT8
(3) Present colour system NTSC/PAL/SECAM/COMP15K/COMP33K/COMP45K/COMP28K/COMP31K
(4) Inducing display EUROPE/RUSSIA/SWEDEN
(5) Model name MODEL NAME
(6) Item name Max. 30 char
(7) Parameter Max. 60 char
3–2
LC-52DH77E/RU/S
5. Adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page Line Item Description Remarks (adjustment detail, etc.)

1/16 [INFO]
1 MAIN Version Main software version
2 BOOT Version BOOT Version.
3 Monitor Version Monitor software version
4 T-CON/H.264 Version T-CON/H.264 Version
5 CPLD Version CPLD Version.
6 EQ DATA CHECKSUM Audio data checksum.
7 LAMP ERROR Number of termination due to lamp error.
8 MONITOR ERR CAUSE Last error standby cause.
9 NORMAL STANDBY CAUSE Situation that became standby at the end. (Excluding the error)
10 ERROR STANDBY CAUSE [1] 0 0H 0M Error standby cause Total operating time before error.
[2] 0 0H 0M
[3] 0 0H 0M
[4] 0 0H 0M
[5] 0 0H 0M
2/16 [INIT]
1 INDUSTRY INIT Enter Initialization to factory settings execution.
2 INDUSTRY INIT (-Hotel) OFF Initialization to factory settings execution. (Hotel mode is excluded)
3 HOTEL MODE OFF Hotel mode ON/OFF setting
4 Center Acutime 5H 0M Main operating hours.
5 RESET OFF Main operating hours reset.
6 Backlight Acutime 19H 35M Backlight operating hours.
7 RESET OFF Backlight operating hours reset.
8 LAMP ERROR RESET OFF Lamp error reset.
9 ADJ PARAM SET Enter ADJ PARAM SET
10 VIC XPOS 0 X-coordinate setting for VIC READ
11 VIC YPOS 0 Y-coordinate setting for VIC READ
12 VIC SIGNAL TYPE MAIN Signal type setting for VIC READ
13 VIC READ OFF Picture level acquisition function
(Level appears in green on the upper right)
3/16 [TUNER ADJ]
1 RF AGC ADJ Enter RF-AGC auto adjustment execution
2 TUNER ADJ Enter TUNER auto adjustment execution
3 PAL+TUNER ADJ Enter PAL TUNER auto adjustment execution
4 RF AGC ADJ (CA-8CH) Enter RF-AGC auto adjustment execution (CA-8CH)
5 TUNER ADJ (CA-8CH) Enter TUNER auto adjustment execution (CA-8CH)
6 PAL+TUNER ADJ (CA-8CH) Enter PAL TUNER auto adjustment execution (CA-8CH)
7 RF AGC 16 RF AGC adjustment
8 TUNER CONTRAST A_GAIN 14 TUNER signal level adjustment
9 TUNER CONTRAST B_GAIN 2048 TUNER signal level adjustment
10 TUNER CONTRAST OFFSET 256 TUNER signal level adjustment
11 RF AGC READ OFF Reading value of RF-AGC voltage
4/16 [PAL MAIN]
1 PAL ADJ Enter PAL adjustment
2 SECAM ADJ Enter SECAM adjustment
3 N358 ADJ Enter N358 adjustment
4 PAL CONTRAST A_GAIN 14 PAL contrast adjustment
5 PAL CONTRAST D_GAIN 2048 PAL contrast adjustment
6 PAL CONTRAST OFFSET 256 PAL contrast adjustment
7 SECAM CONTRAST A_GAIN 14 SECAM contrast adjustment
8 SECAM CONTRAST D_GAIN 2048 SECAM contrast adjustment
9 SECAM CONTRAST OFFSET 256 SECAM contrast adjustment
10 N358 CONTRAST A_GAIN 14 N358 contrast adjustment
11 N358 CONTRAST D_GAIN 2048 N358 contrast adjustment
12 N358 CONTRAST OFFSET 256 N358 contrast adjustment
5/16 [CEC TEST]
1 HDMI CEC TEST Enter HDMI CEC test
2 INSPECT USB TERM Enter Reading inspection of USB memory terminal
3 HDMI EDID WRITE Enter HDMI EDID WRITING
4 MONIDATA READ [TEMP/OPC] OFF MONITOR Temperature/OPC Acquisition tool.
5 CAUSE RESET Enter Reset of standby cause
3–3
LC-52DH77E/RU/S
6/16 [COMP15KMAIN]
1 COMP15K ALL ADJ Enter Component 15K picture level adjustment
2 COMP15K MAIN Y GAIN 141 Y GAIN adjustment value
3 COMP15K MAIN CB GAIN 150 Cb GAIN adjustment value
4 COMP15K MAIN CR GAIN 150 Cr GAIN adjustment value
5 COMP15K Y OFFSET 64 Y OFFSET adjustment value
6 COMP15K CB OFFSET 128 Cb OFFSET adjustment value
7 COMP15K CR OFFSET 128 Cr OFFSET adjustment value
7/16 [HDTV]
1 HDTV ADJ Enter HDTV video level adjustment
2 HDTV Y GAIN 141 HDTV Y GAIN adjustment value
3 HDTV CB GAIN 150 HDTV Cb adjustment value
4 HDTV CR GAIN 150 HDTV Cr adjustment value
5 HDTV Y OFFSET 64 HDTV Y OFFSET adjustment value
6 HDTV CB OFFSET 128 HDTV Cb OFFSET adjustment value
7 HDTV CR OFFSET 128 HDTV Cr OFFSET adjustment value
8/16 [ANALOG PC]
1 ANALOG PC ADJ Enter DVI ANALOG video level adjustment
2 R OFFSET 64 R CUTOFF adjustment value
3 G OFFSET 64 G CUTOFF adjustment value
4 B OFFSET 64 B CUTOFF adjustment value
5 R GAIN 44 R DRIVE adjustment value
6 G GAIN 44 G DRIVE adjustment value
7 B GAIN 44 B DRIVE adjustment value
9/16 [SCART]
1 SCART RGB ADJ Enter SCART RGB level adjustment
2 SCART R CUTOFF 64 SCART R CUTOFF adjustment value
3 SCART G CUTOFF 64 SCART G CUTOFF adjustment value
4 SCART B CUTOFF 64 SCART B CUTOFF adjustment value
5 SCART R GAIN 44 SCART R GAIN adjustment value
6 SCART G GAIN 44 SCART G GAIN adjustment value
7 SCART B GAIN 44 SCART B GAIN adjustment value
10/16 [LUMAADJ]
1 VCOM ADJ 0 Common bias adjustment
2 LCD LUMA ADJ Enter Upper and lower brightness difference adjustment
3 LCD LUMA UP 0
4 LCD LUMA DOWN 0
11/16 [FR DDRTEST]
1 DDRA TEST1 Enter Execute DDRA test 1
2 DDRA TEST2 Enter Execute DDRA test 2
3 DDRB TEST1 Enter Execute DDRA test 1
6 FRC ON/OFF Enter Execute FRC ON/OFF
7 SOUSAM DDR BIST Enter
8 SOUSAS DDR BIST Enter
12/16 [LEV]
1 R GAIN (LO) 0 R DRIVE adjustment value
2 G GAIN (LO) 0 G DRIVE adjustment value
3 B GAIN (LO) 0 B DRIVE adjustment value
4 R GAIN (HI) 0 R DRIVE adjustment value
5 G GAIN (HI) 0 G DRIVE adjustment value
6 B GAIN (HI) 0 B DRIVE adjustment value
13/16 [M EEP SET]
1 MONITOR TIME OUT ON Monitor and the main communication time-out setting
2 MONITOR MAX TEMP 32 MONITOR MAX temperature setting
3 MONITOR EEP READ / WRITE WRITE MONITOR EEPROM READ/WRITE Setting/execution
4 MONITOR EEP ADR 0x 0 MONITOR EEPROM arbitrary addressing
5 MONITOR EEP DATA 0x 0 MONITOR EEPROM arbitrary data specification
14/16 [M TEST PATTERN]
1 LCD TEST PATTERN OFF Pattern with built-in LCD controller display
2 LCD AGI TEST PATTERN
3 LCD EVA TEST PATTERN
4 YEL TEST PATTERN
3–4
LC-52DH77E/RU/S
15/16 [FR REGI]
1 READ/WRITE READ Read/Write
2 SLAVE/ADDRESS SLAVE0 Slave address
3 RESISTER ADDRESS 0x 0 Register address
0x 0
4 WRITE DATA 0x 0 Writing data
0x 0
5 READ DATA 0x 0 Reading data
0x 0
16/16 [ETC]
1 EEP SAVE OFF Writing setting values to EEPROM.
2 EEP RECOVER OFF Reading setting values from EEPROM.
3 MONITOR ERROR CAUSE RESET OFF Reset of monitor error cause
4 STANDBY CAUSE RESET OFF Reset stand by cause.
5 MODEL NAME DH77 Model name setting
6 PANEL SIZE 52 Panel size setting. (32/37/42/46/52/65)
7 PRODUCT EEP ADR 0x 0 Don't touch when serving (for producer of factory)
8 PRODUCT EEP DATA 0x 0 Don't touch when serving (for producer of factory)
3–5
LC-52DH77E/RU/S
6. Special features
1. NORMAL STANDBY CAUSE (Page 1/16)
Display of a cause (code) of the last standby.
The cause of the last standby is recorded in EEPROM whenever possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
2. EEP SAVE (Page 16/16)
Storage of EEP adjustment value
3. EEP RECOVER (Page 16/16)
Retrieval of EEP adjustment value from storage area.
7. Lamp error detection

1. Function
This LCD colour TV set incorporates a lamp error detection feature that automatically turns off the power for safety under abnormal lamp or lamp
circuit conditions. If by any chance anything is wrong with the lamp or lamp circuit or if the lamp error detection feature is activated for some rea-
son, the following will result.
1) The power is interrupted in about 6 seconds after it is turned on.
(The power LED on the front of the TV set turns red from green and keeps blinking in red: ON for 300ms and OFF for 1500ms.).
2) If the above phenomenon 1) occurs 5 times consecutively, it becomes impossible to turn on the power. (The power LED remained red).
2. Measures
1) Checking with lamp error detection OFF
Enter the adjustment process mode, referring to 2. Entering and exiting the adjustment process mode.
If there is a problem with the lamp or lamp circuit, the lamp will go out. (The power LED is green.)
Then, you can check the operation to see if the lamp and lamp circuit are in trouble.
2) Resetting the lamp error count
After the lamp and lamp circuit are found out of trouble, reset the lamp error count. If a lamp error is detected five consecutive times, the power
cannot be turned on. Using the cursor ( / ) key, move to the cursor to [LAMP ERROR RESET], Line 8 on adjustment process mode ser-
vice page 2/16.
With the cursor (</>) keys, select the [LAMP ERROR RESET] value. Finally press the cursor (OK) eys to reset the value to “0”.
Table of contents of adjustment process mode Page 2/16
INDUSTRY INIT Enter

INDUSTRY INIT (-Hotel) OFF
HOTEL MODE OFF
Center Acutime 5H0M
RESET OFF
Backlight Acutime
RESET OFF
LAMP ERROR RESET OFF Resetting to "0"
ADJ PARAM SET Enter
VIC XPOS 0
VIC YPOS 0
VIC SIGNAL TYPE MAIN
VIC READ OFF
3–6
LC-52DH77E/RU/S
8. Public Mode (Hotel Mode)
1. Starting the Public Mode
• There are two following ways to display the PUBLIC Mode setting screen.
1) On the process adjustment mode screen (2/16), set the “HOTEL MODE” Flag to ON.
Turn off the power, and turn it on again, pressing the CHANNEL UP and Volume UP keys of the main unit at the same time.
2) Enter the Pass Word, and start the unit.
a) Turn on the power, pressing the INPUT and Volume UP keys of the main unit at the same time.
b) Display the Pass Word input screen.
Public Mode Public Mode Public Mode
Operation procedure
• The initial input position is the digit at the left end.
• For the numeric keys 0 to 9 of R/C, key input is accepted. Input of the other keys is prohibited.
• Change “–” to “*” by inputting the numeric key at the input position, and shift the input position rightward one digit.
• When three digits are completely input, the Pass Word is judged.
c) Check the Pass Word by inputting three digits.
If the Pass Word is 0 2 7 , it shifts to the PUBLIC Mode setting screen.

In another case, the screen is erased, and it operates in the ordinary mode.
2. Exiting the Public Mode screen
• There are two following ways to exit the Public Mode setting screen.
1) Turn off the power.
2) Select “Execution” in the PUBLIC_Mode to execute it.
Activate the restart under the set content. Here, the START input SOURCE setting is excluded since this item is referred to only when the
power is turned on.
3. Set value of the Public Mode
• When the shipment setting is done, a set each value in Public Mode is initialized.
(PUBLIC MODE in the process mode Setting of a flag is also initialized)
• Separately, the shipment beginnings when all except for each set value in Public Mode is initialized are provided for a process mode.
(INDUSTRY INIT (-HOTEL))
• Only when turning on the HOTELE MODE item, each setting is effective.
• After it decides it with EXECUTE, it AC OFF/ON it to reflect a set value.
3–7
LC-52DH77E/RU/S
4. Basic operation in the Public Mode
Volume ( / ) or Cursor (</>) Change or execution of the set value.
Channel ( / ) or Cursor ( / ) Movement to the selected item.
Decision (ok) Execution (Used by the items “Execution” and “RESET”.)
PUBLIC Mode R/C Ordinary operation mode: It enters the PUBLIC Mode.
PUBLIC MODE Flag is set to “ON”.
PUBLIC Mode: It exits the PUBLIC Mode.
PUBLIC MODE Flag does not change.
Any set item in PUBLIC Mode is not initialized.
Public Mode
POWER ON FIXED [VARIABLE]
SHUT DOWN MODE [NORMAL]
MAXIMUM VOLUME [60]
VOLUME FIXED [VARIABLE]
VOLUME FIXED LEVEL [20]
RC BUTTON [RESPOND]
PANEL BUTTON [RESPOND]
MENU BUTTON [RESPOND]
AV POSITION FIXED [VARIABLE]
ON SCREEN DISPLAY [YES]
INPUT MODE START [NORMAL]
INPUT MODE FIXED [VARIABLE]
LOUD SPEAKER [ON]
RC PATH THROUGH [OFF]
232C POWON [DISABLE]
HOTELMODE [ON]
RESET
EXECUTE
5. Operation after “RESET”

Select “RESET” in the PUBLIC Mode, and it operates as follows when it is executed (refer to the basic operation).
• The set contents in the PUBLIC mode are initialized.
• It does not exit the PUBLIC mode.
• If “EXCUTE” is not executed, the content that does RESET is not reflected.
3–8
LC-52DH77E/RU/S
6. Setting items (* Item names and selective items are expressed in English.)
1) Power ON fixed [POWER ON FIXED]
Option “VARIABLE”, “FIXED_ALL”, “FIXED_BODYKEY” or “RCRESPOND” (loopenabled)

Default “VARIABLE”
Function • When set to “FIXED_ALL”, the “POWER/RECEPTION” key on the main unit or remote control is disabled.
However, the power can be turned off using the “MAIN POWER” switch.
• For some models, the (MAIN) POWER switch is also disabled.
• When set to “FIXED_BODYKEY”, only the “MAIN POWER” key on the main unit is disabled (the remote control is
enabled).
• When selecting “RC RESPOND”, the main unit’s POWER switch toggles between ON and Standby (the same
operation as the remote control).
Key disabled when set • OFF TIMER (SLEEP)
other than default
Remarks • When selecting to “FIXED_ALL”, it functions with the correspondence which isn’t done about other standby fac-
tors (see below).
• No operation OFF
• No signal OFF (including the power management)
If the power button is pressed in the ordinary mode when set to “FIXED_ALL”, the caution is displayed for 5 seconds.
When power button on the main unit is pressed When power button on R/C is pressed
No Power off by power button. No Power off by remote control.
* The OSD display is an example.

If another ODS is previously displayed, the status is reset (MENU or similar).
2) Instantaneous current shutdown setting when turning off the power [SHUT DOWN MODE]
Option “NORMAL” or “QUICK”

Default NORMAL
Function • Scanning or recording of the digital tuner is enabled/disabled when turning off the power.
It is possible to put into the standby state instantaneously due to power off input.
Remarks When selecting “QUICK”, the function does not work for the following items (The possibleme thod differs from model
to model: deleting the item, selection impossible, etc.)
• ON TIMER, QUICK START, DIGITAL FIXED, etc.
3) Volume maximum level [MAXIMUM VOLUME]
Option 0 ~ 60 (loopdisabled)
Default 60
Function • The volume cannot be increased more than the adjusted value (the main unit’s speaker only).
Remarks • When set to 59 or less, only the figure is displayed in the normal mode; the volume bar is not displayed.
• The volume of the headphones or monitor output is limited.
• The setting is impossible when VOLUME FIXED is set other than VARIABLE.
4) Volume fixed [VOLUME FIXED]
Option “VARIABLE”, “FIXED”, “ACCTRL” or “AC/RCCTRL” (loopenabled)

Function • FIXED: The volume is fixed to the value adjusted in the volume fixed level.
• AC CTRL: In the case of ACON, the unit starts at the volume specified in the volume fixed level.
• AC/RC CTRL: The unit starts at the volume specified in the volume fixed level.
Exception • In the adjustment process, the volume can be set to any level regardless of this setting.
Key disabled when set • VOLUME UP/DOWN (VOL+/-) [both remote control and main unit]
to FIXED • MUTE (MUTE) * The main unit’s keys for the menu operation are enabled.
Remarks • VOLUME FIXED has priority over MAXIMUM VOLUME.
• The volume of the headphones or monitor output is fixed.
• The volume is not displayed when operating the above disabled keys.
3–9
LC-52DH77E/RU/S
5) Volume fixed level [VOLUME FIXED LEVEL]
Option 0 ~ 60 (loop disabled)

Default 20
Function The volume is fixed to the adjusted value (the main unit’s speaker only).
Exception • In the adjustment process, the volume can be set to any level regardless of this setting.
Remarks • When setting VOLUME FIXED to “VARIABLE”, the setting cannot be changed.
• VOLUME can be abbreviated to VOL.
6) Remote control operation [RC BUTTON]
Option “RESPOND”, “NO RESPOND” or “LIMITED” (loop enabled)

Default RESPOND
Function The operation of the remote control’s keys is set.
• When set to “NO RESPOND” the remote control’s keys in the normal state are disabled.
The POWER key (RECEPTION/STANDBY key) is also disabled.
• When set to “LIMITED”, only a part of keys (CHANNEL, etc.) is enabled and other keys are disabled. (POWER,
VOLUME ( / ), CHANNEL ( / ), LIGHT CONTROL (BRIGHTNESS SENSOR), BROADCAST
SELECT)
Exception • The PROCESS MODE, INSPECTION MODE and HOTEL MODE keys are enabled regardless of this setting.
• All the keys are enabled regardless of this setting while entering the process mode, inspection mode or hotel
mode.
Remarks The keys enabled when set to “LIMITED” correspond to those on the remote control for hotel; they differ from model
to model.
7) Main Unit Operation [PANEL BUTTON]
Option “RESPOND” or “NO RESPOND” (loop enabled)

Default RESPOND
Function NO RESPOND: The main unit’s keys are disabled excluding the POWER key (RECEPTION/STANDBY key).
Exception • The start operation in the process mode, inspection mode or hotel mode is enabled regardless of this setting.
mode.
• For the main unit’s MENU key, menu operation is possible regardless of the setting during the initial setting when
the power is turned on for the first time.
8) Menu operation [MENU BUTTON]
Option “RESPOND” or “NO RESPOND” (loop enabled)

Default RESPOND
Function The MENU key on the main unit or remote control is disabled.
Exception • The PROCESS MODE, INSPECTION MODE and HOTEL MODE keys are enabled regardless of this setting.
mode.
Key disabled when set All the direct transition keys to menu display (AUTO PRESET, MANUAL MEMORY and others)
other than default
excluding the MENU key
Remarks When set to “NO RESPOND”
• For the models with the MENU key on the main unit, menu operation is possible regardless of the setting during
the initial setting when the power is turned on for the first time.
9) AV position fixed [AV POSITION FIXED]
Option “VARIABLE” or “FIXED” (loop enabled)

Function • When set to “FIXED”, the image adjustment and sound adjustment items in the menu are fixed in the selected
state.
• When receiving “AV POSITION” of the remote control, only the actual state is displayed, and no setting is
changed.
Remarks • When receiving the sound select direct keys (AV POSITION key, OPC, DOLBY key, etc.), only the actual state is
displayed; no setting is changed.
• Since the settings for the hotel mode are retained even after the personal data is initialized, each item for the AV
position and image adjustment and each value for the sound adjustment are not initialized.
3 – 10
LC-52DH77E/RU/S
10)OSD display [ON SCREEN DISPLAY]
Option “YES”, “NO” or “LIMITED” (loop enabled)

“LIMITED” is looped only in case of need (destination).
Default YES
Function • When set to “NO”, the following OSD is not displayed.
Registration, setting, adjustment menu, channel call, volume bar, and input select.
• When set to “LIMITED”, only a part of OSD is not displayed.
Key which may be * OK if simple input select occurs or the original state returns soon if left.
enabled (Example of the
confusing key)
Key disabled when set * The keys by which visibility of the screen or sound is changed cannot be used.
other than default STILL IMAGE, SCREEN DISPLAY, OFF TIMER, AV POSITION, BRIGHTNESS SENSOR, SCREEN SIZE
(example) SELECT, AUTO PRESET, MANUAL MEMORY, IMAGE SELECT, SOUND SELECT, LANGUAGE
Remarks • When set to “NO”,
The set time of OFF TIMER “SLEEP” is cleared.
When the card function is set to “NO”, all the functions including input select and direct keys are invalid.
11)Start mode [INPUT MODE START]
Option “NORMAL” or “Input source 1 (input selection or channel)” • • • (loop enabled)

Default NORMAL
Function The input source or channel to start when turning on the power is set.
If “NORMAL”, the content of the last memory is followed.
Remarks • When set other than “NORMAL”,
Display of the channel setting menu and channel setting operation are prohibited.
• When set to “NORMAL”, “START MODE FIXED” is set to “VARIABLE” and selection is prohibited.
Example of option: “NORMAL”

“TVD (002TV)”, “INPUT1”, “INPUT2”, “INPUT3”, “PC”, “HDMI1”, “HDMI2”, “HDMI3”, “INPUT8”
12)Input fixed [INPUT MODE FIXED]
Option “VARIABLE” “FIXED”, “AC CTRL” or “AC/RC CTRL” (loop enabled)

Default VARIABLE
Function When set to “FIXED”, switching to another channel or input is impossible after start-up in the set value of “INPUT
MODE START”.
When set to “AC CTRL”, the unit starts in the set value of “INPUT MODE START” in the case of the ACON only.
When set to “AC/RC CTRL”, the unit starts in the set value of “INPUT MODE START”.
Key disabled when set CHANNEL ( / ), DIRECT CHANNEL buttons, FLASHBACK, INPUT SELECT, TV/VIDEO, AUTO PRESET,
To “FIXED” (example) MANUAL MEMORY, i.LINK, DIRECT INPUT SELECT, ATV, DTV, EPG, RADIO
Remarks • If the “START MODE” setting is “NORMAL”, this item cannot be set.
Set to “VARIABLE”.
• When set to “FIXED”
The channel setting menu and input selection menu in the menu are not displayed.
13)Speaker ON/OFF selection [LOUD SPEAKER]
Option “ON” or “OFF” (loop enabled)

Default ON
Function The sound from the speakers is not output even if the headphones are not used.
Remarks • When the VOLUME UP/DOWN key is pressed, the mute icon is displayed for 4 seconds.
• For the MUTE key and sound-related keys, caution is displayed.
• For the headphones and monitor output sound, normal operation is possible.
14)Remote control path through [RC PATH THROUGH]
Option “OFF”, “ON: TV RCE” or “ON: TV RCD” (loop enabled)

Default OFF
Function The signal received by the remote control’s light-receiving section is output to the blank pin (9pin) of RS232C.
Exception • Even in the case of “ON: TV RCD”, the PROCESS MODE, INSPECTION MODE and HOTEL MODE keys are
enabled.
• Even in the case of “ON: TV RCD”, all the keys are enabled while entering the PROCESS MODE, INSPECTION
MODE and hotel mode.
Remarks • The model always outputting and that impossible to output exist due to the structure of the hardware.
3 – 11
LC-52DH77E/RU/S
15)232C power ON control [232C POWON]
Option “ENABLE” or “DISABLE” (loop enabled)

Default DISABLE
Function Power ON by the 232C command is enabled/disabled in the standby state.
The same function as 232C command “RSPW”.
“ENABLE”: POWR0001 is always enabled.
“DISABLE”: Start-up may be impossible at POWR0001.
(If the 232C command reception module is set to OFF, the command is invalid.)
16)Hotel mode setting [HOTELMODE]
Option “OFF” or “ON” (loop enabled)

Default OFF
Function The items set in the hotel mode setting menu are enabled or disabled.
The same item as [HOTELMODE] in the adjustment process menu.
Remarks • Each operation of the hotel mode is impossible unless this item is set to ON.
9. Video signal adjustment procedure

The adjustment process mode menu is listed in Section 5.
Signal generator level adjustment check (Adjust to the standard value level.)
• Composite signal PAL/SECAM : 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
• RGB signal : 0.7Vp-p ± 0.02Vp-p
• 15K component signal (50 Hz) : Y level : 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
: PB, PR level : 0.7Vp-p ± 0.02Vp-p
• 33K component signal : Y level : 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
: PB, PR level : 0.7Vp-p ± 0.02Vp-p
1. Process mode
Adjustment point Adjustment Conditions Adjustment procedure

1 Process mode Enter the process adjustment mode using the process adjustment remote con-
trol.
2. PAL signal adjustment

1 Setting [Signal] • Send the PAL full field colour bar (colour saturation: 75%) signal to the
PAL full field colour bar SCART video input of EXT1.
[VIDEO input signal]
[Terminal]
EXT1 SCART video input
100% white
2 Auto adjustment Process page No. 4/16 Point the cursor to [PAL ADJ] and press the [OK] key.
performance The adjustment is complete when [PAL ADJ OK] is displayed.
CAUTION: When performing “(2) PAL signal adjustment” after completing all the adjustments, be sure to execute “(3) TUNER adjustment”.
3 – 12
LC-52DH77E/RU/S
3. TUNER adjustment

1 Setting [Signal] • Send the in-house signal (PAL colour bar) to TUNER.
PAL split colour bar In-house UV • For the PAL colour bar pattern (E-12ch), the picture level and sync level must
show a ration of 7 to 3.
[Terminal] [In-house E-12CH]
TUNER
100% white
2 Auto adjustment Process page No. 3/16 Point the cursor to [TUNER ADJ] and press the [OK] key.
performance The adjustment is complete when [TUNER ADJ OK] is displayed.
4. SECAM signal adjustment

1 Setting [Signal] • Send the SECAM full field colour bar (colour saturation: 75%) signal to the
SECAM full field colour bar SCART video input of EXT1.
[VIDEO input signal]

[Terminal]
EXT1 SCART video input
100% white
2 Auto adjustment Process page No. 4/16 Point the cursor to [SECAM ADJ] and press the [OK] key.
performance The adjustment is complete when [SECAM ADJ OK] is displayed.
5. ADC adjustment (Component 15K)

1 Setting [Signal] • Send the component 15K 100% full field colour bar (colour saturation: 100%)
COMP15K 50Hz 100% full field signal to the component input of EXT3.
colour bar
[Terminal]
EXT3 component input 100% white Black
2 Auto adjustment Process page No. 6/16 Point the cursor to [COMP 15k ALL ADJ] and press the [OK] key.
performance The adjustment is complete when [COMP 15k ALL OK] is displayed.
3 – 13
LC-52DH77E/RU/S
6. ADC adjustment (Component 33K)

1 Setting [Signal] • Send the component 33K 100% full field colour bar (colour saturation: 100%)
COMP33K 50Hz 100% full field signal to the component input of EXT3.
colour bar
[Terminal]
EXT3 component input 100% white Black
2 Auto adjustment Process page No. 7/16 Point the cursor to [HDTV ADJ] and press the [OK] key.
performance The adjustment is complete when [HDTV ADJ OK] is displayed.
7. PC (Analog D-sub 15-pin) signal adjustment

1 Setting [Signal] • Send the XGA 60Hz 100% full field color bar (color saturation: 100%) signal
XGA 60Hz to the PC input of EXT4.
100% full field color bar
[Terminal]
EXT4 PC input 100% white Black
2 Auto adjustment Process page No. 8/16 Point the cursor to [ANALOG PC ADJ] and press the [OK] key.
performance The adjustment is complete when [ANALOG PC ADJ OK] is displayed.
8. RGB (SCART) signal adjustment

1 Setting [Signal] • Send the RGB 15K 100% full field color bar (color saturation: 100%) signal to
RGB 15K 60Hz the SCART input of EXT1.
100% full field color bar
[Terminal]
EXT1 SCART RGB input 100% white Black
2 Auto adjustment Process page No. 9/16 Point the cursor to [SCART RGB ADJ] and press the [OK] key.
performance The adjustment is complete when [SCART RGB ADJ OK] is displayed.
3 – 14
LC-52DH77E/RU/S
10. White Balance Adjustment
Adjustment point Adjustment conditions Adjustment procedure

1 Setting Light control: MAX (+16) 1) Confirm the setting conditions.
2) Connect the white balance adjustment jig.
(Place the luminance meter in 3) Display the adjustment screen by the RS-232C command.
the center of the screen.)
2 Automatic adjustment [Command] [Adjustment procedure]
execution Process mode 1) Transmit the “monitor adjustment process” code using the remote control.
KRSW0001 2) Set the point 6 to the specified gradation, specify the strongest color as the
KKT10037 fixed color, and adjust the RGB so that it becomes the standard value through
negative adjustment.
Setting 3) Set the point 5 to the specified gradation, set the G correction value (3200 x G
KY0F0000 value of point 6/3712) (fractions rounded off), and adjust the RB so that it
0SDS0001 becomes the standard value.
SBSL0016 4) Set the point 4 to the specified gradation, set the G correction value (2176 x G
value of point 6/3712) (fractions rounded off), and adjust the RB so that it
Multi-point adjustment mode becomes the standard value.
MSET0001 5) Set the point 3 to the specified gradation, set the G correction value (1824 x G
value of point 6/3712) (fractions rounded off), and adjust the RB so that it
Adjustment value initialization becomes the standard value.
MSET0004 6) Set the point 2 to the specified gradation, set the G correction value (1248 x G
value of point 6/3712) (fractions rounded off), and adjust the RB pattern so
Point 6 that it becomes the standard value.
LEV60232 7) Set the point 1 to the specified gradation, set the G correction value (768 x G
MG6G**** value of point 6/3712) (fractions rounded off), and adjust the RB so that it
MG6B**** becomes the standard value.
MG6R**** 8) Write the adjustment value by the MSET0003 command and turn off the AC
power.
Point 5 * RGB initial value of point 6: Set gradation 3712
LEV50200 * RGB initial value of points 1 to 5: G correction value of each point
MG5G**** (At each point, adjustment is made so that the remainder of the RGB adjust-
MG5B**** ment value/4 is equal.)
MG5R****
[Adjusted value]
Point 4 * According to the “Standard settings” submitted by the Technical Department.
LEV40136
MG4G**** [Adjustment standard value]
MG4B**** Measuring instrument: [Minolta CA-210] Technical measuring instrument
MG4R**** Level Reference Adjustment Inspection
value spec spec
Point 3 x = 0.272
LEV30114 Point 6 928 ±0.001 ±0.002
y = 0.277
MG3G****
x = 0.272
MG3B**** Point 5 800 ±0.001 ±0.002
y = 0.277
MG3R****
x = 0.272
Point 4 544 ±0.0015 ±0.003
Point 2 y = 0.277
LEV20078 x = 0.272
Point 3 456 ±0.0015 ±0.003
MG2G**** y = 0.277
MG2B**** x = 0.272
Point 2 312 ±0.003 ±0.006
MG2R**** y = 0.277
x = 0.272
Point 1 Point 1 192 ±0.0035 ±0.007
y = 0.277
LEV10048 Remarks Setting conditions when performing inspection
MG1G****
AV MODE: [DYNAMIC]
MG1B****
Monochro: ON
MG1R**** Aging Time: Min. 60 minutes
Writing
MSET0003
11. Confirmation item

1. HDMI-CEC inspection
Check that the HDMI-CEC circuit is operating.
3 – 15
LC-52DH77E/RU/S
12. Initialization to factory settings
After completing the factory setting, turn off the AC power.
CAUTION: Do not turn on the power after completing the factory setting. If the power is turned on, configure the factory setting again. Do not turn off
the power using the remote control.
Adjustment Adjustment conditions Adjustment procedure

point
1 Factory setting Complete the setting by In INDUSTRY INIT of the process page No. [2/16], select the destination [EUROPE / RUS-
turning off the AC power. SIA / SWEDEN] using the [R/C] Volume +/- keys, and press the [R/C] OK key.
“///////////” is displayed, and then “SUCCESS ----- Destination” appears to complete the set-
ting.
Success: Background color [Green] / Failure: Background color [Red]

Initialize the following items when configuring the factory setting.
1) User setting values
2) Channel data (broadcasting frequency, etc.)
3) Manufacturer option setting values
4) Password data
13. Upgrading the software

1. Turn off the AC power (Unplug the AC power cord).
2. Insert the upgrading USB flash memory for upgrade into the service slot.
3. While holding down the power button, plug in the AC power cord of the main unit to turn on the power.
4. Upgrade begins automatically.
After the set starts, the upgrade screen like the figure below is displayed.
Software Update
DH77
MAIN 0%
SUB MICON 0%
PANEL EEPROM NO DATA
MAIN Versiin 1.00

SUB MICON Version 1.00
5. If any of the procedures fails, the following upgrade failure screen shows up. For the failing procedure, the “NG” marking turns red.
NOTE: In such case, try to upgrade the software again. If it still fails, the hardware may be in trouble.
Software Update
DH77
MAIN 30%
SUB MICON 30%
MAIN Versiin 1.00

3 – 16
LC-52DH77E/RU/S
6. When all the procedures are complete, the following upgrade success screen shows up. The new software version can be confirmed on screen.
The version number appears when each item has been successfully upgraded. Finally the main version number appears on screen.
Software Update
DH77
UPGRADE SUCCESS
MAIN 100%
SUB MICON 100%
MAIN Versiin 1.00

7. Turn off the AC power (Unplug the AC power cord). Take out the upgrading USB flash memory.
It waits for about 20 seconds until the AC power supply is turned off.
8. Now the software has been upgraded.
NOTE: Then get the set started and call the process adjustment screen 1/16 to check the main software version.
CAUTION: 1) Do not take out and put in the USB flash memory during formatting.
2) It takes about one minute to the rewriting completion.
Please confirm the upgrade status on the screen becomes 100%.
3) The AC power supply of the set is waited for about 20 seconds until off (The AC outlet is pulled out) after the upgrade is completed.
3 – 17
LC-52DH77E/RU/S
CHAPTER 4. TROUBLESHOOTING TABLE
LC52DH77E
Service Manual
[1] TROUBLESHOOTING TABLE

No power supply (Front LED does not light up) and no power-up even if turned on (Front LED light up).
Is the wire harness in the unit properly connected? NO Reconnect and recheck the wire harness.
YES
Are F7000 and F7001 normal? NO Are FL7001, L7000, L7001, Z7002, BD7000, Z7800, etc. faulty?
Check if the peripheral circuits are short-circuited.
YES
Is B_BUS (+320V) output? (Set the main power SW to OFF.) NO Does the PFC circuit normally work?
* When power on/off switch is on ... About +400V (Check IC7801, L7801, D7806, D7805, Q7804, Q7805, Q7807,
Q7808, etc. and the peripheral circuits.)
YES
Is BU+5V supplied from pin (11) of connector PD when the power NO Check the peripheral circuits on the primary side of IC7905,
switch is turned off? T7901, etc. and the secondary side of D7918, IC7906, IC7907,
etc.
YES
Are INV60V and 13.5V output as for the power on/off switch NO Does the inverter circuit operate normally?
when it is on? Check circuit around the primary side (T7001, T7600, IC7603,
IC7601, IC7600, Q7600-2, D7608, D7610, D7613, etc.), the sec-
ondary side (D7561-2, L7560, D7150-1, L7150, L7560, etc.), the
PS_ON circuit (Q7300-1, etc.), and the protection circuit.
YES
Similarly, is PNL12V output as for the power on/off switch when it NO Check PNL_POW circuit of Q7121-3, etc. and the circuit around
is on? the regulator circuit etc. of IC7121, D7127, etc.
4–1
LC-52DH77E/RU/S
The sound is not emitted from the speaker though the picture has come out.
No sound output in all modes?
Is the SPK_OUT communication output to from pins (N29/ NO Check IC3302 and its peripheral circuits.
SPK_OUT_R) (N30/SPK_OUT_L) of IC3302
(Digital AV decode & Main CPU)?
YES
Is the SPK_OUT communication sent to pins (3), (7) of IC2701 NO Check the line between IC3302 and IC2701.
(POWER_AMP) from of IC3302?
YES
Is the audio signal output of pins (27, 28/L-ch), (11, 12/R-ch) of NO Check IC2701 and its peripheral circuits.
IC2701 (POWER_AMP) normal?
YES
Is the audio signal output of pins (1, 2/L-ch), (4, 3/R-ch) of P2701 NO P2701 (SP) terminal and the peripheral circuit (L/C filter) are
(SP) terminal normal? checked.
YES
Check Speaker (right and left) and wire harness.
No sound (during the reception of TV (ANALOG) broadcasting)
Does not the sound go out though the picture has come out when UHF/VHF is received?
Is a SIF signal output from pin (4) of TUNER (TU1101)? NO Check the tuner and its peripheral circuits.
Replace as required.
YES
Is a SIF signal input to (AB27/S_IF) of IC3302 (Digital AV decode NO Check the line between TU1101 and IC3302.
& Main CPU) from pin (4) of TU1101? (Q1104, etc.)
YES
Refer to “No sound output in all modes”.
4–2
LC-52DH77E/RU/S
No sound (during the reception of TV (DIGITAL) broadcasting)
Does not the sound go out though the picture has come out when DTV is received?
Is IF signal output from pins (16, 17) of TU1101? NO Check the tuner and its peripheral circuits.
YES
Is IF signal sent to pin (AA29/D__IF_P, AB29/D__IF_N) of NO Check the line between TU1101 and IC3302.
IC3302 (Digital AV decode & Main CPU)?
YES
No sound from external input devices (1)
Does not the sound of the audio signal input to EXT1/EXT2 go out?
Is there a audio input signal in pins (6/SC1_IN_L) and (2/ NO Check the setting of an external input device that connects with
SC1_IN_R) of EXT1 (SC503)? EXT1.
Is there a audio input signal in pins (6/SC2_IN_L) and (2/ NO Check the setting of an external input device that connects with
SC2_IN_R) of EXT2 (SC502)? EXT2.
YES
Is there a audio input signal in pins (V28/SC1_L) and (V27/ NO Check the line between SC503 and IC3302.
SC1_R) of IC3302 (Digital AV decode & Main CPU) from SC503?
Is there a audio input signal in pins (U27/SC2_L) and (U26/ NO Check the line between SC502 and IC3302.
SC2_R) of IC3302 (Digital AV decode & Main CPU) from SC502?
YES
Does not the sound of the audio signal input to EXT3 go out?
Is there a audio input signal in pins (2/COMP_IN_L) and (4/ NO Check the setting of an external input device that connects with
COMP_IN_R) of EXT3 (J502)? EXT3.
YES
Is there a audio input signal in pins (U29/COMP_L) and (U28/ NO Check the line between J502 and IC3302.
COMP_R) of IC3302 (Digital AV decode & Main CPU) from
J502?
YES
4–3
LC-52DH77E/RU/S
Does not the sound of the audio signal input to HDMI-2 Does not the sound of the audio signal input to PC mode go
mode go out? out?
Checked whether to have selected “EXT4 (RGB)” “by the Audio Checked whether to have selected “HDMI-2” “by the Audio setup
setup of the HDMI option.” of the HDMI option.”
YES YES
Is there a audio input signal in pins (2/PC/HDMI_L) and (3/PC/HDMI_R) of HDMI-2/PC (J501)?
NO
Check the setting of an external input device that connects with
HDMI-2/PC.
YES
Is there a audio input signal in pins (V30/PC/HDMI_L) and (V29/ NO Check the line between J501 and IC3302.
PC/HDMI_R) of IC3302 (Digital AV decode & Main CPU) from
J501?
YES
Does not the sound of the audio signal input to EXT8 go out?
Is there a audio input signal in pins (5/CVBS_IN_L) and (4/ NO Check the setting of an external input device that connects with
CVBS_IN_R) of EXT8 (J505)? EXT8.
YES
Is there a audio input signal in pins (R28/CVBS_L) and (T28/
CVBS_R) of IC3302 (Digital AV decode & Main CPU) from J505?
YES
Does not the sound of the audio signal input to EXT4/5/6 (HDMI) go out?
Does not the picture/sound of the HDMI signal input to HDMI-1/2/3 go out?
4–4
LC-52DH77E/RU/S
The audio signal is not output (1)
No audio signal output from EXT1/EXT2 terminal.
Is there a audio input signal in pins (3/TUNER_OUT_L) and (1/ YES Check the setting of an external input device that connects with
TUNER_OUT_R) of EXT1 (SC503)? EXT1.
Is there a audio input signal in pins (3/MONITOR_L) and (2/ YES Check the setting of an external input device that connects with
MONITOR_R) of EXT2 (SC502)? EXT2.
NO
Is (AF11/SC1-MUTE) of IC3302 (Digital AV decode & Main CPU) YES Check the peripheral circuits of IC3302 and SC1-MUTE.
at H? (Q502, D529 etc.)
Is (AG11/SC2-MUTE) of IC3302 (Digital AV decode & Main CPU) YES Check the peripheral circuits of IC3302 and SC2-MUTE.
at H? (Q501, D528 etc.)
NO
Is there a audio output signal in pins (N27/TUNER_OUT_L) and YES Check the line between IC3302 and SC503.
(N28/TUNER_OUT_R) of IC3302 (Digital AV decode & Main
CPU)?
Is there a audio output signal in pins (M30/MONITOR_L) and YES Check the line between IC3302 and SC502.
(M29/MONITOR_R) of IC3302 (Digital AV decode & Main CPU)?
NO
Check IC3302 and its peripheral circuits.
No audio signal output from AUDIO_OUTPUT terminal.
Is audio signal (L/R) output to pins (2, 4) of AUDIO_OUTPUT ter- YES Check the connection to AUDIO_OUTPUT terminal and external
minal (J506)? input devices.
NO
MONITOR_MUTE signal [AF13/MONI_MUTE] of IC3302 (Digital YES Check the peripheral circuits of IC3302 and MUTE-A_ALL_LINE.
AV decode & Main CPU) or MUTE_A_ALL signal [21pin of (D526, etc.)
IC2002 (UCOM)] will be “H”?
NO
Is audio signal (L/R) input to pins [M29/MONITOR_R] [M30/ YES Check the line between IC3302 and J506.
MONITOR_L] of IC3302? (Q507, 508, Q509, D526)
NO
4–5
LC-52DH77E/RU/S
No sound from HEADPHONE_OUTPUT terminal.
Is the HP_PLUG signal input to [H28/HP_PLUG] of IC3302 NO Check the line between J504 and IC3302.
(Digital AV decode & Main CPU) from pin (6) of a
HEADPHONE_OUTPUT terminal (J504)?
YES
Is the audio signal output (HP_L/R) to pins (2, 3) of HEAD- YES Check the HEADPHONE terminal (J504) and/or peripheral cir-
PHONE terminal (J504)? cuits.
NO
Is HP-MUTE [AG13/HP_MUTE] of IC3302 at H? YES Check the peripheral circuits of IC3302 (CPU) and HP-
MUTE_LINE. (D527,Q506, etc.)
NO
Is audio signal (HP_L/R) input to pins [M28/HP_L] [M27/HP_R] of YES Check the line between IC3302 and J504.
IC3302?
NO
No sound from DIGITAL AUDIO OUTPUT terminal.
Is the audio signal output to pin (1) of sound output terminal YES Check D520 and/or peripheral circuits.
(D520)?
NO
Do SPDIF_MUTE signal [F7/SPDIF_MUTE] of IC3302, MUTE- YES Check IC3302, IC2002, its circumference circuit and
A_ALL signal [2pin of IC2002 (UCON)] become H? SPDIF_MUTE_LINE, MUTE-A_ALL_LINE. (Q505, D530, etc.)
NO
Is an audio signal input to pin (3) of IC503, from [J28/OPT_OUT] YES Check the IC503 and/or peripheral circuits.
of IC3302 and is the logic signal input into pin (1) of IC503?
NO
4–6
LC-52DH77E/RU/S
No picture on the display (1)
The picture doesn't appear in all modes.
Is the LVDS signal output from IC3302 (DIGITAL_AV_DECODER_&_MAIN_CPU_&_VIDEO PROCESSER) respectively?

TA1_P/M (AC25/AC26), TB1_P/M (AD25/AD26), TC1_P/M (AE25/AE26), TD1_P/M (AE24/AF24), TE1_P/M (AE23/AF23), TCLK1_P/M (AF25/
AF26), TA2_P/M (AE22/AF22), TB2_P/M (AE21/AF21), TC2_P/M (AE20/AF20), TD2_P/M (AE18/AF18), TE2_P/M (AE17/AF17), TCLK2_P/M
(AE19/AF19)
NO
Check IC3302 and its peripheral control circuits.
(IC2002, IC3501, IC3502, X3302, etc.)
YES
Is the above-mentioned LVDS signal output to connector P2601? NO Check the line between IC3302 and P2601.
YES
Similarly, is LCD controller's control signal normal? NO Please check each control signal of L/R, U/D, HV_MODE,
ROMSEL_0/1, TEMP3/2/1, OS_EN, SHIP_EN, and PE.
PANEL_UNIT: YES
Is the LVDS signal input to connector LW of the panel module? NO NO Wire harness (LW) is checked.
YES
Check the panel module.
Does not the picture come out when VHF/UHF is received?
Is the video signal (TUNER_CVBS) output from pin (6) of NO Check the tuner and its peripheral circuits.
TUNER (TU1101)? Replace as required.
YES
Is the video signal (TUNER_CVBS) sent to pin (AD29/ NO Check the line between TU1101 and IC3302. (Q1106, etc.)
TU_CVBS) of IC3302 (Digital AV decode & Main CPU)?
YES
Refer to “The picture doesn't appear in all modes.”
Does not the picture come out when DTV is received?
Is IF signal output from pins (16, 17) of TU1101? NO Check the tuner and its peripheral circuits.
YES
Is IF signal sent to pins (AA29/D__IF_P, AB29/D__IF_N) of NO Check the line between TU1101 and IC3302.
YES
Refer to “No sound output in all modes”
4–7
LC-52DH77E/RU/S
[External input EXT1, EXT2] No picture on the display (4)
Does not the picture of the CVBS signal input to EXT1 go out?
Is CVBS signal sent to pin (20) of EXT1 (SC503)? NO Check the setting of an external input device that connects with
EXT1.
Is CVBS signal sent to pin (20) of EXT2 (SC502)? NO Check the setting of an external input device that connects with
EXT2.
YES
Is CVBS signal from EXT1 (SC503) sent to pin (AG29/ NO Check the line between SC503 and IC3302.
SC1_CVBS_Y) of IC3302 (Digital AV decode & Main CPU)?
Is CVBS signal from EXT2 (SC502) sent to pin (AH30/ NO Check the line between SC502 and IC3302.
SC2_CVBS_Y) of IC3302 (Digital AV decode & Main CPU)?
YES
[External input EXT1, EXT2] No picture on the display (5)
Does not the picture of the Y/C video signal input to EXT1 go out?
Does not the picture of the Y/C video signal input to EXT2 go out?
Is Y/C video signal sent to pins (20)/Y and (15)/C of EXT1 NO Check the setting of an external input device that connects with
(SC503)? EXT1.
Is Y/C video signal sent to pins (20)/Y and (15)/C of EXT2 NO Check the setting of an external input device that connects with
(SC502)? EXT2.
YES
Is Y/C signal from EXT1 (SC503) sent to pins (AG29/ NO Check the line between SC503 and IC3302.
SC1_CVBS_Y) and (AG28/SC1_C1) of IC3302 (Digital AV
decode & Main CPU)?
Is Y/C signal from EXT2 (SC502) sent to pins (AH30/ NO Check the line between SC502 and IC3302.
SC2_CVBS_Y) and (AH29/SC2_C2) of IC3302 (Digital AV
decode & Main CPU)?
YES
Refer to “The picture doesn’t appear in all modes.”
[External input EXT1] No picture on the display (6)
Does not the picture of the R/G/B signal input to EXT1 go out?
Is RGB1 signal sent to pins (15)/R1, (11)/G1 and (7)/B1 of EXT1 NO Check the setting of an external input device that connects with
(SC503)? EXT1.
YES
Is RGB1 signal from EXT1 (SC503) sent to pins (AH22/RED1), NO Check the line between SC503 and IC3302.
(AJ22/GREEN_1) and (AJ21/BLUE_1) of IC3302 (Digital AV
decode & Main CPU)?
YES
Refer to “The picture doesn’t appear in all modes.”
4–8
LC-52DH77E/RU/S
Does not the picture of the component video signal input to EXT3 go out?
Is a COMPONENT video signal input to pins (3)/Y, (5)/Pb, (7)/Pr NO Check the setting of an external input device that connects with
of EXT3 (J503)? EXT3.
YES
Is COMP_PLUG detection signal to (AF7/COMP_PLUG) of NO Check the line between IC3302 and J503.
IC3302 (Digital AV decode & Main CPU) input from pin (2) of
EXT3 (J503)?
YES
Is COMPONENT signal sent to pins (AJ18/COMP__Y), (AJ19/ NO Check the line between IC3302 and J503.
COMP__Pb) and (AH19/COMP__Pr) of IC3302?
YES
Does not the picture of the DVI (ANALOG) video signal input to EXT4 (15pin-D-SUB terminal) go out?
Are the video signal and the synchronized signal input from pins NO Check the connection and setup with the external DVI devices.
(1, 2, 3)/(R, G, B), (14 and 13)/(V, H.Sync) of EXT4 (SC501)?
YES
Are the video signal and the synchronized signal input from pins NO Check the line between SC501 and IC3302.
(AK17/PC__R) (AK16/PC__G) (AH15/PC__B) and (AK14/
PC_HSYNC) (AJ14/PC_VSYNC) of IC3302 (Digital AV decode &
Main CPU)?
YES
Is a CVBS signal input to pin (6) of EXT8 (J505)? NO Check the setting of an external input device that connects with
EXT8.
YES
Is V3_PLUG detection signal input to pin (AJ1/CVBS_PLUG) of NO Check the line between J505 and IC3302.
IC3302 (Digital AV decode & Main CPU) from pin (7) of EXT8
(J505)?
YES
Is CVBS signal sent to pin (AE29/CVBS__IN) of IC3302? NO Check the line between J505 and IC3302.
YES
4–9
LC-52DH77E/RU/S
[External input HDMI-1/2/3] No picture on the display (10)
Does not the picture/sound of the HDMI signal input to HDMI-1/2/3 go out?
Is the Hot plug detection function output from pin (19) of the NO Check the line between SC1502 and pin (31) of IC1504 (HDMI-
HDMI-1 (SC1502) normal? SW).
NO
HDMI-1/2/3.
YES
Is EDID data pins (30/HDMI1_SCL), (29/HDMI1_SDA) of IC1504
accessed, and is it read from pins (15, 16) of a HDMI-1
(SC1502)?
Is EDID data pins (34/HDMI2_SCL), (33/HDMI2_SDA) of IC1504 NO Is access possible in the exchange of IC1504?
(SC1501)?
Is EDID data pins (40/HDMI3_SCL), (39/HDMI3_SDA) of IC1504
(SC1501)? NO
Check the peripheral circuit of SC1501, SC1502, SC1503,
IC1504.
YES
Is TMDS signal input into pins (66, 65/HDMI1_CLKP/N), (68, 67/ NO Check the line between HDMI-1 (SC1502) and IC1504.
HDMI1_D0P/N), (70, 69/HDMI1_D1P/N), (72, 71/HDMI1_D2P/N)
of IC1504 from HDMI-1 (SC1502)?
HDMI2_D0P/N), (6, 5/HDMI2_D1P/N), (8, 7/HDMI2_D2P/N) of
IC1504 from HDMI-1 (SC1503)?
HDMI3_D0P/N), (16, 15/HDMI3_D1P/N), (18, 17/HDMI1_D2P/N)
of IC1504 from HDMI-1 (SC1501)?
YES
Are TMDS_Rx and the I2C_SINK signal output from IC1504 NO Check the IC1504 and peripheral circuits.
respectively?
Pins (62, 63/SW_TMDS_CLKP/N), (60, 61/SW_TMDS_D0P/N),
(58, 59/SW_TMDS_D1P), (56, 57/SW_TMDS_D2P)
YES
Is the TMDS_Rx/ I2C_SINK signal input to IC3302 (Digital AV NO Check the line between IC1504 and IC3302.
decode & Main CPU)?
Pins (AK6, AJ6/SW_TMDS_CLKP/N), (AK7, AJ7/
SW_TMDS_D0P/N), (AK8, AJ8/SW_TMDS_D1P), (AK9, AJ9/
SW_TMDS_D2P) from IC1504
YES
Refer to “The picture doesn't appear in all modes.” or “No sound
output in all modes.”
4 – 10
LC-52DH77E/RU/S
<During external connection> No picture on the monitor (1)
No picture appears on EXT1/EXT2 connected monitor during the VHF/UHF reception.
Is CVBS signal output into pin (19) of EXT1 (SC503) from pin YES Check the setting of an external input device that connects with
(67) of IC504 (TUNER OUT)? EXT1.
(65) of IC508 (MONITOR OUT)? EXT2.
NO
Is CVBS signal input to pin (6) of IC504 from pin (2) of IC507 YES Check the IC504 and their peripheral circuits.
(MUX)?
Is CVBS signal input to pin (1) of IC508 from pin (AJ24/ YES Check the IC508 and their peripheral circuits.
CVBS_MONI_OUT) of IC3302 (Digital AV decode & Main CPU)?
NO
Is TUNER_CVBS signal input to pin (6) of IC507 from TUNER YES Check the IC507 and their peripheral circuits (IC3302).
(TU1101)?
Is TUNER_CVBS signal input to pin (AD29/TU_CVBS) of IC3302 YES Check the IC3302 and their peripheral circuits.
from TUNER (TU1101)?
NO
Is TUNER_CVBS signal output from pin (6) of TUNRE YES Check the line between TU1101 and their peripheral circuits
(TU1101)? (Q1106).
NO
Whether the TUNER circuit operates correctly is checked.
4 – 11
LC-52DH77E/RU/S
No picture appears on EXT1/EXT2 connected monitor during the DTV reception.
(67) of IC504 (TUNER OUT)? EXT1.
(65) of IC508 (MONITOR OUT)? EXT2.
NO
Is CVBS signal output into pin (1) of IC508 from pin (AJ24/ YES Check the IC508 and their peripheral circuits.
Is CVBS signal input to pin (6) of IC504 from pin (2) of YES Check the IC504 and their peripheral circuits.
IC507 (MUX)?
NO
Is TUNER_CVBS signal input to pin (4) of IC507 from YES Check the IC507 and their peripheral circuits.
pin (AK24/CVBS_TU_OUT) of IC3302 (Digital AV
decode & Main CPU)?
NO NO
Is IF signal sent to pins (AA29/D__IF_P, AB29/D__IF_N) of YES Check the IC3302 and their peripheral circuits.
NO
Is IF signal output from pins (16, 17) of TU1101? YES Check the line between TU1101 and IC3302.
NO
Whether the TUNER circuit operates correctly is checked.
No picture from EXT1 appears on EXT2-connected monitor.
Is CVBS signal output into pin (19) of EXT2 (SC502)? YES Check the setting of an external input device that connects with
EXT2.
NO
NO
Is CVBS signal sent to pin (AG29/SC1_CVBS/Y) of IC3302 (Dig- YES Check the IC3302 and their peripheral circuits.
ital AV decode & Main CPU) from EXT1 (SC503)?
NO
Is CVBS signal sent to pin (20) of EXT1 (SC503)? YES Check the line between EXT1 (SC503) and IC3302.
NO
EXT1.
4 – 12
LC-52DH77E/RU/S
No picture from EXT8 appears on EXT2- connected monitor.
Is CVBS signal output into pin (19) of EXT2 (SC502)? YES Check the setting of an external input device that connects with
EXT2.
NO
NO
Is CVBS signal input to pin (AE29/CVBS__IN) of IC3302 from YES Check the IC3302 and their peripheral circuits.
J505?
NO
Is CVBS signal sent to pin (6) of EXT8 (J505)? YES Check the line between EXT8 (J505) and IC3302.
NO
Is V3_PLUG detection signal input to pin (AJ11/CVBS/PLUG) of YES Check the line between EXT8 (J505) and IC3302.
IC3302 from pin (7) of EXT8 (J505)?
NO
EXT8.
4 – 13
LC-52DH77E/RU/S
[2] LED flashing specification at the time of the error
Display method
• Refer to Table 1.
• Make the OPC LED flash using the [MENU] key on the remote control since the display for service persons is identified by the number of flashings
(once to 5 times).
Even if the [MENU] key is pressed again, it does not return to the display for customers (only the power LED flashes).
• After recovering from an error, if the same error cannot be generated again, refer to MONITOR ERR CAUSE on the adjustment process screen.
LED flashing method

• Synchronize the phases of the power LED and OPC LED.
• If the LEDs have different number of flashings, adjust the flashing cycle to that where the LED flashes more times.
<Flashing example for customers>

Power
1500ms
300ms
300ms
<Flashing example for service persons>

Power
OPC
(Displayed by the
specific operation) 1500ms
300ms
300ms
Table 1. Concrete flashing pattern
For customers For service persons

Item Cause
Power OPC Power OPC
Inverter/Lamp system failure Red flashes once Off Red flashes once Flashes once Lamp error
Power PWB failure (Power Red flashes once Off Red flashes once Flashes once AC_DET error
failure, etc.) Flashes twice UR+13.5V error
Flashes 3 times D3.3V error
Flashes 5 times Panel power supply error
Main PWB failure Green flashes once Off Green flashes once Flashes once Initial communication error
(Communication failure, etc.) Flashes twice Start-up confirmation commu-
nication error
Flashes 3 times Regular communication error
Flashes 5 times Other communication error
Others Green flashes twice Off Green flashes twice Flashes once Temperature error
Flashes twice Sync error
Flashes 3 times Notification from the main
microprocessor (*1)
VerUP executing Orange flashes once Off Orange flashes once Off Version upgrading
VerUP succeeded Power green/OPC flash alternately Power green/OPC flash alternately Version upgrade succeeded
VerUP failed Green/Red flash Off Green/Red flash Off Version upgrade failed
alternately alternately
System Red flashes 3 times Off Red flashes 3 times Off Mounting discrimination
connector unplugged
ROM data failure Green/Red flash Off Green/Red flash Off Start-up after failing version
alternately alternately upgrade (*2)
* 1: For details, refer to ERROR STANDBY CAUSE on the adjustment process screen.
* 2: If the boot section is abnormal, there is no flashing (flashing disabled).
4 – 14
LC-52DH77E/RU/S
MONITOR ERR STBY table
Outline: Communication/Power failure detected by the monitor microprocessor (IC2003) is stored on EEPROM, states can be confirmed in
the adjustment process mode.
Location: Page 1/16 of the adjustment process mode: MONITOR ERR CAUSE “0” if there is no error. It is cleared to 0 on the last page of the
adjustment process mode.
Display Error description

02 Start-up communication error 2 Initial communication from the main CPU is not received.
03 Start-up communication error 3 Only the initial communication is received.
04 Start-up communication error 4 Until panel information request reception
05 Start-up communication error 5 Until initialization completion reception
06 Start-up communication error 6 Until version notification transmission
07 Start-up communication error 7 Until start-up information notification transmission
08 Start-up communication error 8 Until start-up information response reception
09 Start-up communication error 9 Until time-out setting reception
0A Communication error A REQ time-out
0B Communication error B Restart time-out during the beginning of time acquisition start-up
0C Communication error C Ending sequence time-out
0D Communication error D Preset start-up time-out during completion
0E Communication error E Download start-up time-out
0F Communication error F Time acquisition time-out
11 Communication error H Regular communication time-out
16 Panel-related error Lamp failure
1A Other error 2 Monitor temperature failure
1D Power supply error 1 PS_ON (AC_DET) failure
1E Power supply error 2 D_POW (DET_12V) failure
1F Power supply error 3 D_POW (DET_D3V3) failure
21 Power supply error 5 Panel power failure
23 Other error 3 Error standby request from the main CPU
LED flashing timing chart at the time of the error

1) Power LED
Error type Power LED operation (1 cycle) Note: Pins are monitor microprocessor pins (IC2003).
H: Red on Refer to “Inverter/Lamp failure details”. OPC_LED flashes by pressing the
[MENU] key on the remote control.
Inverter/Lamp failure
Red flashes once
L: Off
H: Red on Refer to “Power failure details”. OPC_LED flashes by pressing the [MENU]
key on the remote control.
Power failure 300ms 1.5sec
Red flashes twice
L: Off
H: Green on Refer to “Communication failure details”. OPC_LED flashes by pressing
Communication the [MENU] key on the remote control.
failure with main Communication line failure or main CPU communication failure.
CPU
Green flashes once
L: Off
H: Green on Refer to “Other failure details”. OPC_LED flashes by pressing the [MENU]
key on the remote control.
Others
Green flashes twice
L: Off
4 – 15
LC-52DH77E/RU/S
2) Inverter/Lamp failure details (Power red LED flashes once and OPC (preset) LED flashes)
Error type OPC (preset) LED operation (1 cycle) Note: Pins are monitor microprocessor pins unless otherwise specified (IC2002).
H: On ERR_PNL (40pin): Abnormal L. Confirmed after 5 consecutive detections at 1 second
intervals (detected only when the backlight is on).
Note that after five detection counts, the lamp cannot be activated except in the moni-
Lamp failure toring process. (For the first time, only the inverter is reset, and error OFF is not acti-
Flashes once L: Off vated.)
Accumulated counts are cleared to 0 when the setting in the adjustment process is
made, when AC_ON is performed with [CH_DOWN] and [VOL_UP] on the unit down
or after continuous illumination for 3 minutes.
3) Power failure details (Power red LED flashes twice and OPC (preset) LED flashes)
Error type OPC (preset) LED operation (1 cycle) Note: Pins are monitor microprocessor pins unless otherwise specified (IC2002).
PS_ON H: On AC_DET (72pin: Abnormal (L).
AC_DET fail- If error is detected during start-up or operation, the power is turned on again by inter-
ure Flashes rupt handling (instantaneous blackout processing).
once L: Off
H: On DET_12V (34pin): Abnormal (L). Main 12V is not applied.
D_POW
Main 12V
failure
Flashes twice
L: Off If error is detected during start-up or operation, the power is turned on again by polling.
D_POW H: On DET_D3V3 (35pin): abnormal (L). Digital 3.3V is not applied.
Digital 3.3V
Failure
Flashes 3
times L: Off If error is detected during start-up or operation, the power is turned on again by polling.
4) Communication failure details (Power green LED flashes once and OPC (preset) LED flashes)
Error type OPC (preset) LED operation (1 cycle) Note: Basically, debug print logs are analyzed or communication logs
are analyzed by a bus monitor.
Initial communi- H: On Initial communication from the main CPU is not received. (Request for the
cation reception monitor model No. is not received.)
failure Flashes → Communication line failure or main CPU start-up failure
once L: Off
Start-up confir- H: On Start-up reason confirmation from the main CPU cannot be received. (Start-
mation recep- up communication until start-up reason notification command is not
tion failure received.)
Flashes twice → Main CPU start-up failure or monitor microprocessor reception failure
L: Off
Regular commu- H: On Regular communication that is performed at 1 second intervals in the nor-
nication failure mal operation is interrupted.
Flashes 3 times → Main CPU operation failure or monitor microprocessor reception failure
L: Off
H: On When a request (PM_REQ=H) is sent from the main microprocessor, the
Other communi- request command is not output from the main CPU, etc.
cation failure → Main CPU operation failure or monitor microprocessor reception failure
Flashes 5 times
L: Off
5) Other failure details (Power green LED flashes twice and OPC (preset) LED flashes)
Error type OPC (preset) LED operation (1 cycle) Note: Pins are monitor microprocessor pins unless otherwise specified
(IC2002).
H: On If the panel temperature is 60°C or more for 15 seconds or more in a row, CAUTION
appears on the OSD (flashes in red in the lower right screen).
Monitor temper-
If the panel temperature is 60°C or more for 25 seconds or more in a row, error
ature failure
standby is activated.
Flashes once
(MONITOR MAX TEMP on page 13/16 of the adjustment process: Change of tem-
L: Off perature failure AD value): Thermistor
H: On Main microprocessor detection error (CPU temperature error, etc.)
Details are displayed on page 1/16 of the adjustment process for the main micropro-
Main failure cessor.
Flashes 3 times
L: Off
4 – 16
LC-52DH77E/RU/S
CHAPTER 5. BLOCK DIAGRAM/WIRING DIAGRAM
LC52DH77E
Service Manual
[1] MAIN BLOCK DIAGRAM
MAIN BLOCK DIAGRAM

S8V TO_LCD_CONT
P2601(LW) 41
AF27 CPU_TN0 K26,L26 L2601 GND
R3336 4 8 40
AE27 CPU_TP0 LVDS0_D0N D14 TA1- TA1- AIN0-
R3337 3 7 39
LVDS0_D0P C14 TA1+ TA1+ AIN0+
2 6 38
LVDS0_D1N D15 TB1- TB1- AIN1-
1 5 L2606 37
C3360 T27 LVDS0_D1P C15 TB1+ TB1+ AIN1+
4 8 36
//C3361 C3362 P28 LVDS0_D2N D16 TC1- TC1- AIN2-
C3365 3 7 35
J
//C3363 P29 LVDS0_D2P C16 TC1+ TC1+ AIN2+
//C3366 34
GND
2 6 33
LVDS0_CLKN D17 TCLK1- TCLK1- ACK-
L2602 1 5 32
SC1_CVBS/Y AG29 SC1_CVBS_Y LVDS0_CLKP C17 TCLK1+ TCLK1+ ACK+
TU1101 D5V
Q1103 SC1FSW AJ23 SC1FSW LVDS0_D3N D18 TD1- TD1-
4 8 31
AIN3-
TUNER 3 7 30
SC1_CVBS/Y SLOWSW_1 AH28 SLOWSW_1 LVDS0_D3P C18 TD1+ TD1+ AIN3+
ANT_IN RF MB VIDEO IF IF IF 2 6 29
SC1FSW AGC (IF5V) SIF AFT OUT AS SCL SDA AGC N.C N.C GND AGC (D2) (D1) BLUE1 AJ21 BLUE1 LVDS0_D4N D19 TE1- TE1- AIN4-
SLOWSW_1 1 5 28
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 GREEN1 AJ22 GREEN1 LVDS0_D4P C19 TE1+ TE1+ AIN4+
EXT1 SC1_IN_L
IC508 S+8V
RED/C1
27
AH22 RED L2604 GND
SC503 MM1756 DC-POW MB(5V)
4 8 26
D5V SW 1 VOUT VDD 1 LVDS1_D0N B14 TA2- TA2- BIN0-
3 7 25
(G20) (G16) CTRL AGND 5V_REG. SC2_CVBS/Y AH30 SC2_CVBS_Y LVDS1_D0P A14 TA2+ TA2+ BIN0+
+5V(CONT) 2 6 24
20 18 16 14 12 10 8 6 4 2 SC1_IN_R 6 Vcc VIN 1 2,5 GND Vin 3 SLOWSW_2 AJ28 SLOWSW_2 LVDS1_D1N B15 TB2- TB2- BIN1-
L2603 1 5 23
VIN BLANK RSV SLOWSW AIN_L AIN_R 5 PS GND 2 RED/C1 AH29 SC2_C2 LVDS1_D1P A15 TB2+ TB2+ BIN1+
4 OUT BIAS 3 Q1101 IC1105 COMP_Pr
4 8 22
VOUT/L RED/C AO-L AO-R AH19 COMP_Pr LVDS1_D2N B16 TC2- TC2- BIN2-
L1101 PQ1KA503 3 7 21
21 19 17 15 13 11 9 7 5 3 1 TUNER_OUT_R Q1104 D5V COMP_Pb AJ19 COMP_Pb LVDS1_D2P A16 TC2+ TC2+ BIN2+
Q502 6 1 20
(G19) (G15) (G11) (G7) BUFF. COMp_Y AJ18 COMp_Y GND
MUTE R1102
6 5 4 C1103 2 CVBS_IN 2 6 19
AE28 CVBS_IN LVDS1_CLKN B17 TCLK2- TCLK2- BCK-
OUTV_SC1 RED/C1 GREEN1 BLUE1 1 5 L2605 18
TUNER_OUT_L AJ24 CVBS_MONI_OUT LVDS1_CLKP A17 TCLK2+ TCLK2+ BCK+
R1101 D3.3V 4 8 17
I
MUTE_A_ALL AK24 CVBS_TU_OUT LVDS1_D3N B18 TD2- TD2- BIN3-
3 3 7 16
SC1_MUTE 5 ANT_+5V_SW A29 TU_CVBS LVDS1_D3P A18 TD2+ TD2+ BIN3+
1 2 3 2 6 15
D529 LNB_SHORT LVDS1_D4N B19 TE2- TE2- BIN4-
4 Q1102 1 5 14
BLUE1 INV. LVDS1_D4P A19 TE2+ TE2+ BIN4+
D_IF_N AB29 D_IF_N 13
GREEN1 GND
D_IF_P AA29 D_IF_P 3
RED1/C1 PNL_WP AH2 PNL_WP L_R R/L
IF_AGC 9
SC1_V_OUT PNL_ROM_EN AH1 PNL_ROM_EN U_D U/D
ANA_POW_SW
OPC AK27 OPC O_S_SET HV_MODE
TUNER_SDA L28 TUNER_SDA PNL_EN A28 PNL_EN FRAME ROMSEL1
SC2_CVBS/Y IC504 IC507 L29 TUNER_SCL CBOOT G30 CBOOT ROMSEL0 ROMSEL0
TUNER_SCL
MM1506XN MM1507XN CVBS_MONI_OUT AF7 COMP_PLUG PM_REQ G29 PM_REQ TEMP3 TEMP3
SLOWSW_2
D5V SW D5V MULTIPLEXER COMP_PLUG AJ1 CVBS_PLUG Q2003 BU3.3V
TEMP2 TEMP2
EXT2 AVLINK CVBS_PLUG
SC502 K28 IF_AGC CNVss F30 TEMP1 TEMP1
SC2_IN_L 3 Vcc IN1 6 3 Vcc IN2 6 TUNER_CVBS E9 ANA_POW_SW PE PE

Q2004
2 OUT IN2 4 2 OUT IN1 4 A29 TUNER_CVBS_SEL Q2603 BU3.3V OS_EN
(G20) (G16) CTRL AGND 1 SW GND 5 1 SW GND 5 AH10 TU_OUT_CVBS_MUTE IC2005 AVCC:97/VREF:96 SHIP_EN
SIF
CPU_RXD0_UCOM
CPU_TXD0_UCOM
VCC1:14/VCC2:60
20 18 16 14 12 10 8 6 4 2 SC2_IN_R H28 HP_PLUG LCX125FT D2003 D3.3V
RS_BUF_CNT
UCON_RST
VIN BLANK RSV SLOWSW AIN_L AIN_R CVBS_TU_OUT AG13 HP_MUTE SC504 12 11 R2041
AV_LINK 3 AV_LINK_I EXE_LED 47
RS-232C
N_RESET
IR_RS
H VOUT/L RED/C AO-L AO-R TUNER_CVBS_SEL F7 SPDIF_MUTE 13
STB
BU3.3V R2019
21 19 17 15 13 11 9 7 5 3 1 MONITOR_R TU_OUT_CVBS_MUTE AF13 MONI_MUTE 8 10
11
20 AV_LINK_O QSTEMP 80
Q501
(G19) (G15) (G11) (G7) MUTE PC/HDMI_L 15 VCC 9
5
6 5 4 PC/HDMI_R AF11 SC1_MUTE D3.3V 5 6 TH2001
HDMI2/PC RS_BUF_CNT F29 16
9
BU3.3V SHDN CEC_0 4 CEC_0_IN
OUTV RED/C2 GREEN2 BLUE2 AVSS
MONITOR_L AUD-IN(L/R) HP_L AG11 SC2_MUTE 4 94
TO_INVERTER
4
UCON_RST F28 7
J501
MUTE_A_ALL HP_R 3 5 5 2A 3 1 D3.3V P9602(LB)
8
PC/HDMI_L CPU_UARXD2_UCOM H25 13 22 CEC_0_OUT
SC2_MUTE 2 SC1_IN_L AH12 SP_MUTE 2Y 7 11 2 DET_POW2_PNL12V 35 DET_PNL12V R2602 7
3
3 PC/HDMI_R REG2
1 2 3 R2405 R2011
7
D528 SC1_IN_R CPU_UATXD0_RS AK13 6
7
1 6 2B 9 DET_POW3_D3V3 36 D3.3V TL9632 REG
RED2/C2 HP_PLUG SC2_IN_L AB27 SIF IA 2 8
6
2
4 1Y N_SRESET 78 SRESET TL9630 OSC
SC2_V_OUT HP_L SC2_IN_R V30 PC_HDMI_L R2021 5
2
6
ANT+5V_SW 43 ANT_POW POW13V LAMP_ERR ERR
COMP_IN_R V29 PC_HDMI_R 3 1B DET_POW1_13V 34
HP_R G25 GND 14 2
1
CPU_UATXD2_UCOM STB 49 STB
3
1 15 VON STB
Q506 COMP_IN_L M28 HP_L LOGIC R2035 3
CBOOT 74 CBOOT
10
S /ST OFL1 OFL1
4
1 4 CVBS_IN_L M27 HP_R IC506 9

5 2 6 2 M3221EIP 21 MUTE_ALL_A OFL2 OFL2
5
CVBS_IN_R V28 SC1_L CPU_UARXD0_RS AJ13 MUTE_ALL_A 8

EXT3 RS-232C_I/F ERR_PNL 40 TL9633 BRT
MONITOR_L V27 SC1_R VON
1
J502
6 3
IC8451 IC8452 1
S_GND
COMP_IN_R J504 MONITOR_R U27 SC2_L LNB_SHORT 41 LNB_SHORT 58
HEAD_PHONE 7WH126FU LCX157FT IC2007 7 CNVSS
COND_TEST
J503
COMP_IN_L
AUDIO TUNER_OUT_R U26 SC2_R
BUFFER SWITCH CNVSS P8_4 16
AUDIO
4
TUNER_OUT_L U29 COMP_R
STB3.3V AHC1G08W PM_REQ 77 PM_REQ
Y PB PR R2018
R-IN IC9601
G
7 COMP_Pr 4
U28 COMP_L W28,AG16,AG27,AJ27 1
5 AMP13V
OPT_OUT HC2G66DP FROM_POWER
COMP_Pb R28 CVBS_L STB_CPU AH3 STB_CPU
2 3
2 1 7,3 2 P9601(PD)
AUDIO COMp_Y PVDDREG:1 SPK_OUT_L T28 CVBS_R OFL1 K27 OFL1 OFL1
L-IN PVDDPR/L:10,32 INLP 3 5 6 1-2
2 POW13V
COMP_PLUG P2701(SP) PVDDMR/L:16,26 M30 MONITOR_L OFL2 C5 OFL2 OFL2
3-4
S+13.5V
L2701 VREF 5 M29 MONITOR_R DET_SYNC 18 AMP13.5V UR+13.5V
IC503 LCH(+) 1
30,31 OUTPL D3.3V 11
N28 TUNER_OUT_R E8,E15,E18,E21,E24,F9 DET_COND 25 BU+5V BU+5V
EXT8 T7SET08U1E SP-L L2704 INRP 7 SPK_OUT_R F26,G8,G25,H25,N26,P26 10
J505
DIGITAL SPDIF_BUFF. LCH(-) 2
27,28 OUTML N27 TUNER_OUT_L R26,T25,U25,Y26,AA27 PS_ON PS_ON
9
Y W R
OUTPUT &_SPDIF_MUTE RCH(+) 4
L2702
IC2701 AVDD 2 J28 OPT_OUT AA28,AC28,AC29,AC30 AC_DET AC_DET
4 11,12 OUTPR AD27,AF6,AG5,AG21,AG23 12
PNL_POW
5
CVBS_IN_L D520 D5V SP-R L2703 YDA148QZ N30 SPK_OUT_L AH4,AH6-7,AH9,AJ3 69 PNL_POW
SP_MUTE P3301 5-8
CVBS_IN_R 4
2 RCH(-) 3
14,15 OUTPL POWER_AMP. GAIN0 24 N29 SPK_OUT_R W26 72 AC_DET GND
6 1 R3334 1-4,6 XCIN 8
CVBS_IN 22 NCDRCO MUTEN 19 UR+13.5V UR+13.5V CPU_RXD0_UCOM 76 RXD_CPU X2001
7
CVBS_PLUG
2 1 Q2701 D2707 DDR1.8V(D1.8V) 5 32.768kHz TO_LCD_CONT
AJ6 SW_TMDS_CLKN C1,D2,E3,F4,G5,H6,L2-3 BU+5V BU+5V CPU_TXD0_UCOM 75 TXD_CPU
3
23 NCDRC1
PLMIT 9 M4,N6,P6,T2,U3,U4,U5 7 XCOUT 9 P2602(LP)
25 FIL_PLL AK6 SW_TMDS_CLKP V4,AB3,AB5-6,AC4 IC3301 AC_DET
XIN 13
BD6538G 8 2 6 9
4 3 Q505
13 PVSSR
SLEEPN 17 D_POW
AJ7 SW_TMDS_D0N AD2,3,AE6,AF5,AG4
LINEAR_REG.
PS_ON IC2008 30 RXD X2002
10
COND_TEST
D5V 9 1 20.000MHz
Q509
SW. 21 CKIN AK7 SW_TMDS_D0P STBY_POW 7WH126FU COND_DET
XOUT 11 15
5
2
INLM 4
AJ8 SW_TMDS_D1N
CPU1.2V
4 VIN VOUT 5
10
USB_POW BUFF. 3 5
29 TXD DET
D527
E17,E19,E22,N11,T10
D530
INRM 6 11,12 7 12
6 18 PROTN AK8 SW_TMDS_D1P W10,W27,AB10,AB12,AB20 EN 1 USB__DP RS_BUF_CNT VCOM_SCL
AUDIO_OUT 1
D526
AJ9 SW_TMDS_D2N AF18,AG18-20,AH24,AJ25 2 GND FLG 3
13,14
USB__DN
13
VCOM_SDA
J506 15-20 11
F HP_PLUG HP_PLUG
AK9 SW_TMDS_D2P GND PNL_WP
PNL_ROM_EN
14
VCOM_WP
LCDC_EN
2
L-OUT
Q507 HP_MUTE HP_MUTE IC2004 1-4
PNL_13.5V
BUFF. D1.05V S24CS08J 5-8
MONI_MUTE MONI_MUTE USB_PWRFLT AG6 USB_PWRFLT GND
MONITOR_L BU+3.3V EEPROM
SPDIF_MUTE SPDIF_MUTE A1-2,B1-2,C2-3,D3-5 USBPWRON AH5 USB_PWRON 1
R-OUT 4
Q508 MUTE_A_ALL MUTE_A_ALL E4-6,F5,F6,G6,K13,L11-12 USB_DN AK5 USB_DN 2 J3301 8 VCC A0 1
BUFF. L15,M11,M19,P10,P19,R11,R18 S2006 S2005 S2004 S2003 S2002 S2001
S S2007
SC1_MUTE SC1_MUTE USB_DP AJ5 USB_DP 3 USB:500mA max W_PROT_M 26 7 WP A1 2 CH-UP CH-DOWN INPUT VOL-UP VOL-DOWN MENU
V POWER
MONITOR_R V18,Y11,AA10,AA12,AA14,AB13
AVLINK AV_LINK 4 IC2006 I2C_SDA 28 5 SDA A2 3
AB15
SC2_MUTE
TCVHC32T
SC2_MUTE 1 I2C_SCL 27 6 SCL VSS 4
3 61 DPOW
1 2 D_POW 2
KEY1 82
R2083 R2082 R2081 R2080
5 6 5 KEY2 83
SMPOWHOLD 6
7,3 4
EXT_SMPOW_HOLD POW_SW 66
J30 SDA0_400k
SW_TMDS_CLKN D1.8V 13 32 Type only
J29 SCL0_400k IC2601 11
PNL_I2C_EN AJ2 PS_ON 12
SW_TMDS_CLKP HC2G66DP VDDQ:3,7,26,28,22 59 SMPOW
S151 S152 S153 S154 S155 S156 S157
D3.3V IC8455 SW_TMDS_D0N BUS_SW. 80,84,63,67
CH-UP CH-DOWN INPUT VOL-UP VOL-DOWN MENU POWER
VDD:1,5,12,18,20
EXT_SMPOW_HOLD
SMPOWHOLD
BR24S64F AE26 SIF_COM BU+3.3V

CEC_0
SW_TMDS_D0P MA_0-12: VDDL:9

N_RESET
EEPROM MA0-12 IC2001 P2002

SW_TMDS_D1N N3,R2,P2,U1,P4,V3, DDR_A0-12 IC2002
OFL2
50,43,75,44,49,73 2 VDD OUT 1 10 RESET

S80927NM
8 VCC A0 1 SW_TMDS_D1P P1,U2,P3,T3,T4,R3,T1 74,45,48,46,43,47,13 IXC786WJ 1 KEY1
RESET
E
C2002
7 WP A1 2 SW_TMDS_D2N MD_0 H5 DDR_DQ0 55 DDR_DQ0
5 CT VSS 3 MONITOR 2 KEY2 R151 R152 R153 R154
6 SCL A2 3 SW_TMDS_D2P MD_1 L4 DDR_DQ1 68 DDR_DQ1 MICROCOMPUTER 3 STBY_POW
5 SDA GND 4 MD_2 H4 DDR_DQ2 79 DDR_DQ2 5 GNB
KEY_UNIT
C3367 AB30 MD_3 E2 DDR_DQ3 2 DDR_DQ3 UCON_RST 42/46/52 Type only
MD_4 D1 DDR_DQ4 8 DDR_DQ4 Q2006 P101
MD_5 J5 DDR_DQ5 21 DDR_DQ5 L_R 57 L_R 2 GND
CEC_LINE D102 D103
AB26 SIF_COM MD_6 F2 DDR_DQ6 6 DDR_DQ6 U_D 56 U_D OPC TVPOW
AMP_PROTECT C3359 1 LED_5V BU3.3V
AD28 TU_GND_REF MD_7 G4 DDR_DQ7 23 DDR_DQ7 TEMP3 55 TEMP3
D1512 R1507 C3364 IC101
TEMP2
1
BU+3.3V MD_8 M5 DDR_DQ8 59 DDR_DQ8 54 TEMP2 OPC+3.3V OPC_SENSOR
MD_9 L5 DDR_DQ9 34 DDR_DQ9 TEMP1 53 TEMP1 P2003/P102 4
G R G/B
3
R3323 AK3,AF22,AH13 MD_10 K3 DDR_DQ10 83 DDR_DQ10 O_S_SET 52 O_S_SET 10 LED_5V 1,2
CI_OEB 117 CI_OEB ,R3333 AG1 IC3302 ROMSEL0 TL2026
D5V D3.3V MD_11 K1 DDR_DQM11 64 DDR_DQ11 ROMSEL0 51 8 OPC
3
,R9984
R3321 IXC773WJ OPC 79 RMC101
CI_DATA0 116 FRAME
CI_DATA0
//R3322 DIGITAL_AV_DECODER MD_12 K2 DDR_DQM12 4 DDR_DQ12 FRAME 50
BU+3.3V
1 BU+3.3V BU3.3V IR_RECEVER
D1511 VCC33: 33,52 R105 R115 R114
68,97,121
CI_DATA1 115 CI_DATA1 &_MAIN_CPU MD_13 L1 DDR_DQM13 25 DDR_DQ13 IC3501 INV. 2 2 OPC+3.3V 3
23 IRPASS D3.3V 1
CI_CEB 94 CI_CE &_VIDEO_PROCESSOR MD_14 L4 DDR_DQM14 2 DDR_DQ14 IXC790WJQZ IR_RS 4 R/C 2
Q105 Q104
Q102
AVDD33_XTAL: 108
RESET_B 107 CI_CNT_RESET
1Gbit 4 1
W29 MD_15 M6 DDR_DQM15 27 DDR_DQ15 7 LED_OPC
X3302 DDR2_MEMORY Q2005 IC2009 LED_OPC 100
CI_INT 114 CI_CNT_INT 6 POWR_LED
27.000MHz
CI_RB 106 TC7SH00U 5 RC LED_R 98
Q103
CI_RB W30 DDR_DQS0 G2 DDR_DQS0 81 DDR_DQS0 5 POWG_LED
LED_G 99
D D1508 D1.8V
VCC18 15,82
CI_WEB 96 XEWE D8
B5
CI_OEB
CI_DATA0
DDR_DQS0#
DDR_DQM0
G1
H1
DDR_DQS0#
DDR_DQM0
57
66
DDR_DQS0#
DDR_DQM0
OPC 3 GND
AVDD18_PLL 112 TS_CPUIN_VAL VSS:12,62 BYTE 6 R/C, LED_UNIT

TS_VAALIDO 122 B6 CI_DATA1 DDR_DQS1 J2 DDR_DQS1 61 DDR_DQS1
TS_CLKO 123 TS_CPUIN_CLK D29 CI_CE DDR_DQS1#
DR_DQS1# J3 29 DR_DQS1#
D1509 124 TS_CPUIN_D0 AF12 CI_CNT_RESET DDR_DQM1
TS_DATAO DDR_DQM1 K4 62 DDR_DQM1
125 TS_CPUIN_SYNC IC9608 STB3.3V
TS_SYNCO
TS_CPUOUT_CLK
B29 CI_CNT_INT DDR_CS0# N1 DDR_CS0# 51 CS0# LV5893M
TO_CLK 6 D28 CI_RB DDR_RAS# P5 DDR_RAS# 77 RAS# DC-DC_CONV. UR+13.5V
TS_CPUOUT_SYNC
D_POW
19 AMP_PROTECT T0_SYNC 7 DDR_CAS# N2 DDR_CAS# 76 CAS# R9650 Q9604

TS_CPUOUT_VAL 7 EN VIN 2 6 3
8
PS_ON
HDMI3_POW5V T0_VALID A30 TS_CPUIN_VAL DDR_WE# W1 DDR_WE# 70 WE# R9652 R9615
TS_CPUOUT_D0 BST 1 2 5
D3.3V T0_DATA0 9 B30 TS_CPUIN_CLK DDR_ODT N4 DDR_ODT 19 ODT C9642 R9650 C9643
D5V 6 COMP L9604 D5V
EXT7 21 23 VCC: 9,27,64 IC4404 C29 TS_CPUIN_D0 DDR_CKE W2 DDR_CKE 41 CKE
8 SS SW. 3
1 4
42 R2PWR5V 6 VIN VO 1
HDMI1
CI_IOIS16 89 WP GPIO_9 93 CI_VCCEN R4427 AOZ1320C C30 TS_CPUIN_SYNC DDR_BA0 V1 DDR_BA0 42 BA0 C9645 D9601 R9616
19 HDMI_HPG3 41 HPD2
SC1501 18
CI_INP_ACK 72 INPACK SC4401 LOAD SW D30 TS_CPOUT_CLK V2 DDR_BA1 71 BA1 R9640 D9613
D9602
D5V DDR_BA1 5 FB GND 4 C9630
17 IC4405 MA332WJSA 3 EN NC 4
E27 TS_CPOUT_SYNC DDR_BA2 W3 DDR_BA2 10 BA2 //9633 (6.2V)
16 HDMI3_SDA 40 DSDA2 5 GND
15 HDMI3_SCL 39 DSCL2 1 GPIO_0 MTB295AE TO_PC_CARD D27 TS_CPOUT_VAL DDR_MCLK0 M2 DDR_MCLK0 53 MCLK0 R9638 //9635
R4428 VSSQ:A7,B2,B8,D2,
14
2 GPIO_1 DTV CI D8,E7,F2,F8 R9612
13 E29 TS_CPOUT_D0 DDR_MCLK0# M3 DDR_MCLK0# 52 MCLK0#
12 HDMI3_CLKN 11 R2XCN R4PWR5V 49
7
Vcc:17,51 D3.3V H2,H8 IC9604 BU+3.3V
CE_1 35 CI_EN1 CE1
11 9 DDR_VREF V5 DDR_VREF 40 VREF VSS:A3,E3,J3,N1,P9 LV58072M
VSSDL:J7 D9603
10 HDMI3_CLKP 12 R2XCP OE 39 CI_OE
15
OE Vcc:12,37 DC-DC_CONV. UR+13.5V Q9601
C
9 HDMI3_D0N 13 R2X0N INV.
8 WE 53 CI_WE WE_PGM WP# 19 FL_VPP0 F28 R9633
16 29 FL_VPP0 D1.8V 7 EN VIN 2 Q9602
7 HDMI3_D0P 14 R2X0P READY 55 CI_IREQ IREQ A0 CI_A0 R9634 INV.
6 HDMI3_D1N 15 R2X2N CE# 9 N_FLS_CS B10 N_FLS_CS C9612
CI_A0 80 A0 42 28 VDDQ:3,7,26,28,22 BST 1 C9615
5 CE_2 36 CI_EN2 CE2 A1 CI_A1 RE# 8 XERE R9632
B9 XERE 80,84,63,67
4 HDMI3_D1P
HDMI3_D2N
16 R2X1P CI_A1 78 A1 VS1 38 CI_VS1
43
VTGSENB A2
27
CI_A2 VDD:1,5,12,18,20
6 COMP L9605 D1.05V
3 17 R2X2N R/B# 7 N_PARB_ A3 N_PARB C9602 R9610
2 CI_A2 75 A2 44 26 VDDL:9 8 SS SW 3
IORD 40 CI_RD IORD A3 CI_A3 PDD0_ 29 I/O0 WE# 18 XEWE_ DDR_A0-12 MA0-12
1 HDMI3_D2P 18 R2X2P 45 25 E14 XEWE C9619
CI_A3 73 A3 IOWR 42 CI_WR IOWR A4 CI_A4 PDD1_ 30 I/O1 50,43,75,44,49,73 R9621 D9613
AG12 SMPOWHOLD 74,45,48,46,43,47,13
20 22
CI_A4 71 A4 58 24 5 FB GND 4 C9607
RESET 67 CI_RESET RESET A5 CI_A5 PDD2_ 31 I/O2 MD_16 Y5 DDR_DQ16 55 DDR_DQ16 //9679
CI_A5 69 A5 59 23 //9610
WAIT 70 CI_WAIT WAIT A6 CI_A6 PDD3_ 32 I/O3 AK27 N_CPU_RST MD_17 AA2 DDR_DQ17 38 DDR_DQ17 R9620
HDMI1_POW5V 32 R0PWR5V CI_A6 66 A6 61 22
REG 74 CI_REG REG A7 CI_A7 PDD4_ 41 I/O4 D5V D9606
36 12 IC501 MD_18 W4 DDR_DQ18 79 DDR_DQ18
D5457
CI_A7 64 A7
IC1504 CD_1 23 CI_CARDDET1 CD1 A8 CI_A8 PDD5_ 42 I/O5
IC8401
D512 BR24C21F MD_19 Y3 DDR_DQ19 68 DDR_DQ19 R9617
67 11
21 23
SII9187
CI_A8 46 A8 CD2 88 CI_CARDDET2 CD2 A9 CI_A9 PDD6_ 43 I/O6
IXC721WJQZ EEPROM MD_20 Y2 DDR_DQ20 8 DDR_DQ20 D9607
CI_A9 44 A9 A18 47 TS_CIIN_D0
47
MD10 A10
8
CI_A10 PDD7_ 44 I/O7 IC9610
19 HDMI_HPG1 31 HPD0 HDMI-SW. 48 10 8 VCC A0 1 NC MD_21 W5 DDR_DQ21 21 DDR_DQ21 UR+13.5V PQ1LAX95
18 CI_A10 37 A10 A19 49 TS_CIIN_D1 MD11 A11 CI_A11 PAALE_ 17 ALE FRASH IC8454 MD_22 AA1 DDR_DQ22 6 DDR_DQ22 S8V
17 7 WP A1 2 NC
16 HDMI_SDA 29 DSDA0 CI_A11 41 A11 A20 51 TS_CIIN_D2
49
MD12 A12
21
CI_A12 PACLE_ 16 CLE MEMORY AHC1G08W 4 VIN Vout 5
6 SCL A2 3 NC MD_23 Y4 DDR_DQ23 23 DDR_DQ23
15 HDMI_SCL 30 DSCL0 50 13
14
CI_A12 67 A12 A21 54 TS_CIIN_D3 MD13 A13 CI_A13 4 1 MD_24 AE2 DDR_DQ24 59 DDR_DQ24 8V_REG. R9657
53 14 5 SDA GND 4 D9656
13 CI_A13 48 A13 A22 56 TS_CIIN_D4 MD14 A14 CI_A14 3 On GND 4
EXT6 12 HDMI1_CLKN 65 R0XCN 54 30 2
MD_25 AD5 DDR_DQ25 34 DDR_DQ25
2
Vadj
CI_A14 50 A14
HDMI2 11 A23 58 TS_CIIN_D5 MD15 D0 CI_D0 R547 MD_26 AE1 DDR_DQ26 83 DDR_DQ26
SC1502 10 HDMI1_CLKP 66 R0XCP CI_D0 83 D0 55 31 Q9609
HDMI1_D0N 67 R0X0N A24 61 TS_CIIN_D6 MD16 D1 CI_D1 16 MD_27 AD4 DDR_DQ27 64 DDR_DQ27 R9658
B
9
8 CI_D1 85 D1 56 32 IC3502
7 HDMI1_D0P 68 R0X0P
A25 63 TS_CIIN_D7 MD17 D2 CI_D2
6 MD_28 AA5 DDR_DQ28 4 DDR_DQ28 IC9605
6 HDMI1_D1N 69 R0X2N CI_D2 87 D2 A17 45 TS_CIIN_SYNC
46
MISTRT D3
2
CI_D3 DDR2_SDRAM LV5893M
11 1 AK17 PC__R MD_29 AE3 DDR_DQ29 25 DDR_DQ29
5 CI_D3 24 D3 20 3 IXC790WJQZ R9645 DC-DC_CONV. UR+13.5V
A15 59 TS_CIIN_CLK MICLK D4 CI_D4 7
4 HDMI1_D1P
HDMI1_D2N
70 R0X1P
19 4
MD_30 AE4 DDR_DQ30 2 DDR_DQ30 1Gbit Q9607 R9626
3 71 R0X2N CI_D4 26 D4 A16 57 TS_CIIN_VAL MIVALK D5 CI_D5
12 2
AK16 PC__G
2 64 5 8
MD_31 AD1 DDR_DQ31 27 DDR_DQ31 DDR2_MEMORY 7 EN VIN 2
1 HDMI1_D2P 72 R0X2P CI_D5 28 D5 D5 81 TS_CIOUT_D0 MOD0 D6 CI_D6 R9637
13 3 AH15 BST 1
CI_D6 30 D6 65 6 CI_D7 PC__B C9624 R9635 C9626
D9 84 TS_CIOUT_D1 MOD1 D7
20 22
CI_D7 66
9
AK14 PC_HSYNC DDR_DQS2 AB2 DDR_DQS2 81 DDR_DQS2 6 COMP L9602 D3.3V
TRWR_CI2CA 55 32 D7 D10 88 TS_CIOUT_D2 MOD2 14 4 DDR_DQS2# DDR_DQS2# DDR_DQS2#
AB1 57 8 SS SW 3
R1509 25 37 Vss:33,36 10 AJ14 PC_VSYNC
HDMI2_POW5V 36 R1PWR5V D11 TS_CIOUT_D3 MOD3 GND DDR_DQM2 AB4 DDR_DQM2 66 DDR_DQM2 C9628
38 1,34,35,68 15 5 R9630 D9611
109 XTAL_0
X4401
D12 27 TS_CIOUT_D4 MOD4
R549 DDR_DQS3 AC2 DDR_DQS3 61 DDR_DQS3 5 FB GND 4 C9611 IC9609
21 23 27.000MHz D13 29 TS_CIOUT_D5
39
MOD5
D3.3V
SC8452
17 //9614 BU+5V TCR5SB33 BU+3.3V
DR_DQS3# AC3 DR_DQS3# 29 DR_DQS3#
110 XTAL_1 40 BU3.3V SC501 R9628
CSDA 30 SDA0_400k D14 31 TS_CIOUT_D6 MOD6
19 HDMI_HPG2 35 HPD1
PDD2_ 41
10 1 EXT4 DDR_DQM3 AC5 DDR_DQM3 62 DDR_DQM3 1 VIN VO 5
18 95 CI_DATA2 MCK
17
CSCL 29 SCL0_400k D15 34 TS_CIOUT_D7 MOD7
11 3 ANALOG(RGB) AF2 DDR_CS0# 51 CS0#
IC9606 3.3V_REG. C9644
PDD3_ 102 CI_DATA3 63 N_HOLD D9614
16 HDM2_SDA 33 DSDA1 TXCN 27 SW_TMDS_CLKN
BVD1 79 TS_CIOUT_SYNC MOSTRT N_EXT_CE E10 N_EXT_CE AF3 DDR_RAS# 77 RAS#
15 HDM2_SCL 34 DSCL1 PDD4_ 101 CI_DATA4 57 MSI
4 LV58072M 3 Vc DGN 2
TXCP 26 SW_TMDS_CLKP VS2 65 TS_CIOUT_CLK MOCLK DDR_CAS#
14
62 5 PDD0 B11 PDD0 76 CAS# DC-DC_CONV. UR+13.5V
13 TX0N 24 SW_TMDS_D0N PDD5_ 100 CI_DATA5 BVD2 77 TS_CIOUT_VAL MOVAL N_MCS R9643
EXT5 12 HDMI2_CLKN 1 R1XCN 6 PDD1 A13 PDD1 GND: DDR_WE# 70 WE#
PDD6_ 99 CI_DATA6 N_MWP 7 EN VIN 2 R9641
HDMI1 11 TX0P 23 SW_TMDS_D0P
GND:10,22,43,60 7
PDD2 C10 PDD2 D27,E1,E16,E20,E23,E26,F11,G3,H2 DDR_ODT 19 ODT
SC1503 10 HDMI2_CLKP 2 R1XCP PDD7_ 98 CI_DATA7 MSO H3,J4,J6,K5,K12,K14-18,K25,L13-14 BST 1 C9629
9 HDMI2_D0N 3 R1X0N TX1N 21 SW_TMDS_D1N PDD3 A11 PDD3 DDR_CKE 41 CKE C9638 C9627 R9639
76,90,104,126, 12 L16-19,L25,M10,M12-18,N10,N12-19
8 TX1P 20 SW_TMDS_D1P PAALE_ 103 CI_ALE SMPOWHOLD
13 PDD4 C13 PDD4 DDR_BA0 42 BA0
6 COMP L9606 D1.8V IC9603
A
7 HDMI2_D0P 4 R1X0P N25,P11-18,P25,R4-6,R10,R12-17
6 HDMI2_D1N 5 R1X2N TX2N 18 SW_TMDS_D2N PACLE_ 105 CI_CLE N_RESET PDD5 A10 PDD5 R19,R25,T11-19,T21,T23-24,T26 DDR_BA1 71 BA1
8 SS SW. 3 MM314YN CPU1.2V
5 14 U10-18,U21-24,V10-17,V20-24,V26 C9632
TX2P 17 SW_TMDS_D2P N_PWB_CHK PDD6 D9612 D9608
4 HDMI2_D1P 6 R1X1P 15 C11 PDD6 W11-18,W20-24,Y6,Y10,Y12-Y18,Y20-24 DDR_BA2 10 BA2 R9631 1 VIN VO 5
3 HDMI2_D2N 7 R1X2N RSVD 10,26 N_EXT_BOOT Y27-30,AA3-5,AA11,AA13,AA15-18,AB11 5 FB GND 4 C9615 (2.4V)
2 2,8,9,16 PDD7 B12 PDD7 AB14,AB16-18,AB28,AC26,AC27,AD6 DDR_MCLK1 53 MCLK0 VSSQ:A7,B2,B8,D2, //9618 C9608 1.25V_REG.
1 HDMI2_D2P 8 R1X2P R1531,R1517 GND PAALE AD26,AE5,AE26,AF4,AF8,AF16,AF17 D8,E7,F2,F8 R9624
C12 PAALE DDR_MCLK1# 52 MCLK0# R9629 //9620 3 ON NC 4 C9604
AF19-20,AF23,AG2-3,AG7-8,AG15,AG17 H2,H8
20 22 PACLE B13 PACLE AG22,AG24,AG26,AH8,AH25-26 DDR_VREF 40 VREF VSS:A3,E3,J3,N1,P9 2 GND
VSSDL:J7 D9609
1 23 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
5–1

LC-52DH77E/RU/S
[2] SYSTEM BLOCK DIAGRAM
SYSTEM BLOCK DIAGRAM
EXT8
J
J505 CVBS_IN
CVBS/LR
CVBS_IN_L/R
EXT1(CVBS/YC/RGB) MAIN UNIT LCD PANEL UNIT

SC1_CVBS/Y
SC503
CVBS/LR SC1_IN_L/R
SC1_Y/C
RGB RGB
SC1_V_OUT
TUNER_OUT SLOWSW2
TUNER_OUT_L/R
LR_OUT
SLOWSW1
FS/FB SC1FSW
AIN0+/-,AIN1+/-,AIN2+/-,AIN3+/-,AIN4+/-,ACK+/-,
BIN0+/-,BIN1+/-,BIN2+/-,BIN3+/-,BIN4+/-,BCK+/-
I IC504 IC507
LW(P2601)
TUNER OUT MUX PE
LW
(41pin)
(41pin)
Disclete
MUTE MM1506XN MM1507XN
EXT2(CVBS/YC) TUNER_CVBS_SEL HV_MODE
TU_CVBS_OUT_MUTE
LCD_CONTROLLER
SC2_CVBS/Y
SC502
CVBS/LR SC2_IN_L/R LCD_PANEL
SC2_Y/C 1920x1080
RGB
SC2_V_OUT
AV_OUT IC508 DET
MONITOR_L/R
LR_OUT MONITOR OUT LCD_EN
Disclete
FS/ MUTE MM1756AU VCOM_SCL/SDA
LP(P2602)
AV_LINK AV_LINK IC2601 VCOM_WP
H
(15pin)
(15pin)
LP
D3.3V Spliter CONT_DET
RGB
SLOWSW2
SLOWSW1
PNL_EN
SC1FSW
LVDS_OUT
CVBS_YU_OUT
IC8455 HC2G66DP
SC2_Y/C
SC1_Y/C
CVBS_MONI_OUT
CVBS__IN
EXT3(COMP/AUD) EXE_LED1 TEST_MODE

SC2_CVBS_Y
SC1_CVBS_Y
PNL_IC2_EN
BR24S64F
J501 COMP_YPbPr EEPROM
CVBS BYPASS
YPbPr/LR COMP_IN_L/R PNL_ROM_EN
PNL_WP
COMP_YPbPr
SP PNL+12V 4 or 5-Wavelength
PL
(4pin)
P2701
SP_L
SPK_OUT IC2701
SP AMP
SP_R YDA148QZ
G
OUTPUT(AUDIO)
MONITOR_L/R Disclete
J506 MUTE SDA.SCL(400Hz)
AUDIO_OUT
INVERTER_UNIT
X4401
Disclete 27MHz D3.3V
REG2
MUTE REG2
LB(CN7502A)
OFL1
SC4401
CI_CEB, CI_RB IC3302 OFL1 IC9601 OFL1
LB(P9602)
IC4405 Spliter
LB1
LB2
CI_D[7:0] /CI_A[14:0] OFL2
(6pin)
(6pin)
(6pin)
Digital AV decode OFL2 OFL2
(9pin)
CI CIEN,CIDET
CI_CNT_RESET HC2G66DP
(COMMON
TS_CI_OUT
CI Controller IXC773WJQZ VON
IC2007 STB
INTERFACE) TS_CPU_IN SW. STB
AHC1G08W ERR
TS_CI_IN MT8295 X2001 X2002 ERR
TS_CPU_OUT 20MHz 20MHz
INV_60V
F
INV_12V
TUNER_CVBS CI_DATA D3.3V
TUNER_CVBS EXE_LED STB
TU1101 D_IF IN P/N LA(CN7501A)
TUNER D_IF IN P/N EXE_LED
IFAGC (3pin)
IFAGC DET_POW2_PNL12V
SIF
SIF AV_LINK AV_LINK_O
DET_SYNC DET_SYNC
TUNER_SDA/SCL AV_LINK_I
IC3501 DET_COND LA
DET_COND
IXC790WJ CEC_LINE TEST_MODE PNL+12V (3pin)
CEC_I12 CONT_TEST
PL
(4pin)
1066Mbit ERR_L
DDR2 CEC_O12 ERR_PNL INV_12V
SPK_OUT_L/R SM_POW PS_ON
ANT_5V_SW ANT_POW
J504 TUNER_OUT_L/R AC_DET AC_DET
HP_PLUG LNB_SHORT LNB_SHORT INV_12V
MONITOR_OUT_L/R
E
INV_60V
HP MUTE_A_ALL MUTE_A_ALL
HP_L/R HP_L/R IC3502
PD(P9601)
CVBS_IN_L/R IXC790WJ I2C1_SCL AMP13V
S+13.5V
(12pin)
(12pin)
1066Mbit
PD
SC1_IN_L/R IC2004 I2C1_SDA UR+13.5V
DIGITAL DDR2 S24C508J
BU+5V
SC2_IN_L/R EEPROM W_PROT_M
AUDIO_OUTPUT
COMP_IN_L/R
IC2002
D520
GPFSV51V OPT_OUT IC503
BU+3.3V MONITOR_MICON BU5V PNL_12V 13V
SPDIF_OUT OPT_OUT IC2001
OPT OUT S80927NM RESET IXC786WJ POWER_SUPPLY
T7SET08 RESET
MUTE
CIRCUIT
AC-DET
PS_ON
UCOM_RST POW13V BACK-UP_SYSTEM
EXT4/6 J506 DET_POW1_13V BU+5V
BU+3.3V
HDMI2/PC
PC/HDMI_L/R D3.3V
AUDIO(R/L) PC/HDMI_L/R RXD/TXD_DBCG DET_POW3_D3V3 MAIN_SYSTEM
D (MINI_PLUG) CNVss D5V
CNVss CNVss D_POW D3.3V BU+5V 13V 60V
D_POW S+8V
P2001 BUSY/CE/EPM/SCLK RS_ON D1.8V
RS_ON
CPU_UARXD2_UCOM
EXT4
CPU_UATXD2_UCOM
SC501 PC_RGB Debug & CPU1.2V

PC_RGB RS_BUF_CNT RXD/TXD D1.05V
Piogram etc.
ANALOG_RGB PC_H/Vsync PC_H/Vsync
N_CPU_RST
(PC)
IC501 SW_TMDS_CLKP/N PM_REQ,CBOOTS
RS_BUF_CNT IC2008
PDD[0:7]
EEPROM SW_TMDS_D0P/N 7WH126FU

USB
BR24C21F SW_TMDS_D1 SW.

STBY SW. SYS INV
IC506 SW_TMDS_D2
MAX3221 TH2001
RS-232C RS232C TxRx
RXD/TXD_CPU QSTEMP
P2603
IC8452 RXD,TXD_CPU DEBUG
SW PM_REQ,CBOOTS
C SC1505 LCX157FT Connector
POW_SW
STBY_POW
KEY2
N_SRESET KEY2
HDMI-4 IC8454 N_SRESET KEY1
SW KEY1
LED_OPC
AHC1G08W
LED_G
LED_R
OPC
RC
IR_PASS
EXT7 SC1501 PFC AC-DET
CONTROL OVP
HDMI_3
POWG_LED
POWR_LED
HDMI-3 IC1504
OPC+3.3V
LED_OPC
BU+3.3V
N_RESET OPC
DDC_3
OPC
SII91873
R/C
TMDS_Rx/ I2C_SINK
SC8452 IC8401
IC2009
EXT6 SC1502
HDMI-SW To External IXC721WJQZ TC7SH00U
DDC_1 Flash Memory 512Mbit IR_SW.
B HDMI-2 FLASH RA(P2003) KM(P2002)

(10pin) (4pin)
HDMI_1
NOISE_FILTER
EXT5 SC1503 RA(P102) KM(P151)

(10pin) (5pin)
DDC_2 D102
HDMI-1
OPC S151 S154 S157
BU3.3V CH-UP VOL-UP POWER
HDMI_2
D103 IC101
TVPOW R OPC
CEC_0 SENSOR
OPC+3.3V
S152 S155 POWER_UNIT

BU+3.3V
CH-DOWN VOL-DOWN
J3301 USB_DP/N G/B
USB IC3301
RMC101
AC_INLET
LINE REG
IR S153
INPUT
S156
MENU
A BD6538G
[DV] INTERFACE
R/C, LED UNIT RECEVER
SC1801(21pin)
KEY UNIT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
5–2

LC-52DH77E/RU/S
[3] OVERALL WIRING DIAGRAM
OVERALL WIRING DIAGRAM
RUNTKA529WJQZ
(INVERTER_UNIT)
I LB
LA
QCNW-H341WJQZ
QCNW-H333WJQZ
G
QCNW-H340WJQZ
F
LB2
9 1
LB
P9602
D7151
Q7152
LB1
IC4405 LA
1
D7150
P2603
SC4401
D7562
19
20
EXT4 PD1
IC7121
(ANALOG_RGB_PC) QCNW-H337WJQZ
EXT4/6
D7561
(PC_AUD/HDMI2)
D7918
SC501 J501
E EXT8(CVBS)
QCNW-H973WJQZ
PL
T7001
12
J505 SC1503 SC1502

IC1504 EXT5(HDMI1) EXT6(HDMI2)
T7901
P9601
PD
IC3302
1
EXT7(HDMI3)
SC1801 IC3502
QCNW-H974WJQZ
POWER_UNIT
SC1802
IC3501
RDENCA308WJQZ
EXT3
AUDIO_OUT
D J503
J506 DIGITAL QCNW-H960WJQZ
AUDIO_OUT
20
19
D520
P3301
J3301
41
KM
P151
1
LW
P2601
Q7601
J504
SC8452
(DUNTKE266WE)
Q7808
EXT1(RGB) EXT2(RGB)
1
Q7602
SC503 SC502
RS-232C
KEY_UNIT
J502 SC504
IC2002
Q7805
15
D7806
15 1 41 1 1 4
P2602
LP
P7002 SC4801 P7003

C
1
QCNW-J553WJQZ
LCD_CONTROL_UNIT
BD7000
CX7000 F7000
T4A H 250V
ANT_IN MAIN_UNIT
(DUNTKF190WE)
F7001
T4A H 250V
14
SP
P2701
P2001
KM RA
P2002 P2003
1 4
1 4 1 10
1
CN7000
B
RUNTKA529WJQZ
(INVERTER_UNIT)
QCNW-H325WJQZ
QCNW-H958WJQZ
P102 R/C,LED_UNIT
(DUNTKF096WE)
SPEAKER_UNIT(L)
SPEAKER_UNIT(R)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
5–3

LC-52DH77E/RU/S
CHAPTER 6. PRINTED WIRING BOARD
LC52DH77E
Service Manual
[1] MAIN UNIT PRINTED WIRING BOARD
MAIN Unit (Side-A)
1 23 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
6–1

I
J
C
D
H
A
B
G
1
2
R2020
P2003 P2002 R2072
S2002
LUG9601
R2068
P2701 R2014
R2030
P2001
FB2001
FB2004
FB2003
FB2002
FB2014
FB2005
C2019
R2025
R1105
C2025 FB2013
C2031 FB2012
C2032 FB2011
C2033 FB2010
C2034 FB2009
C2035 FB2008
D2006
R2081
C2029 C2028 C2027 C1114
FB2006 C2023
R2062
R2047 R2009 R2008 LUG9604
R2063
C2016 C2005 C2004
R2012
3
R2046 R2022 R2010
C2734
C2036 R2049
C2738 C2739 C2737
FB2007 D2008
S2003
TH2001
C2037
C2736 C2735
C1110
R2720
R2721
R2722
R2723
L2705 L2706
C2710
C2730
C2733
C1112
C2732 C2731
D1101
D2706 D2703
MAIN Unit (Chip Parts Side-A)
C1108
C1113
R2701 R2716 R2715
R2724
R2718
R2714
R2717
C2726 C2729
C2720
C2721
C1106
L2704 L2703
C2723
C2724
S2005
C2715
4
C2728
C2725
C2722
C2727
IC2701
C1141
C1140
C2716
C2717
L2701 L2702
L1104
C2719
R1113 R1112
D2704
C2718
R2083
C2708 C2709 R2713 C1138 R1114 R1115
R2712
C2714
C2713
C2706
C2711
C2712
C2707
D2705
Q1104
D529
R566
D2004
R1116
R569 R571
R2725
C541
R645 R570
Q2702
C535
C534
Q2704
C540
S2006
R646 R560
C536
C2705 C2704 R554 R555
R561
R2710 C530 C531
D528
R559
C537
R2708 R2706
R552
R556
C526 C1103
C522
FB515
D2702
Q2703
5
R2082
C9623 C527 FB512
FB516
R553
FB514 FB517
IC9604
FB9602
C523
D9610
C9621
L9605 C525 D502 C533 C1101
Q1102
R558 R565
Q1103
FB511
C529 C539 C1118 L1101
R563 R568 R608
R525
FB527
R510
D525
C1160
S2004
C1122
Q1101
C9625
FB513
FB9603
C9622
C1102
FB518 IC1107 IC1105
C524
C1161
VA505
VA510
FB1102
R557 C532 R548
R1102 R1101
R564
R529
C528 C538
D1102
C1121
C1111
C1119
R562 R567 FL513
FL506 R1134
C520
R1129
C511
R544
FB510 FB508
R2041
R634
R2080
C2024
D513 D505
IC2007 R528 R1106
IC1102
R1133
D2003
R2004
R2079
R2011
R520 R515 R508 R504
FL505 R546
D506 D503
VA509
6
VA504 FL512
R509 R521
R550
C564
R2064 FB519
D514
S2001
R541
R639
D501 C547
R2077 R575
Q2001 R527 R537
C519 C546
R535
R2032 R2033
R574
X2002
C2008
R543 FL504 R576
R2036
R2003
IC2002 FL511
Q2006
R2034
VA508
C517
P2602
R2053 C2009 R542 VA503 R545
FB2612
R2045
R516
FB2613 R2006
D511
R519
C1130
C1129
R2001 D504
C2011
R2043
FB509
FB2614
C1124
C1123
R2070 R540 C1125
FB501
R2057
FB2616 C1131 R1107 R1109 R1108
X2001
D2005
IC2601
R539 R534 R536 FL509
R1110
R1111
C1132
FB2617 FB520 C1133
FB2610 FL510 FL507 FL508 R532 C548
C2015 C2014 C2012
R2042 VA507 R578
C2602
FB2611

R2050
R2071
R2051 VA501 C507 VA502 VA506 C549
7
S2007
R526 C503 R580
R518
R531 R579
R530 R1140
R513
IC1106
X1101
R8460 C593
R8473
R2074
C1147 C1148
D521
D523
C591
IC8405 C8460 IC508
R626
R1126
SC8452 C8461 FB523 R613
C557
R648
C592
C587
R8470
R8480
C8454 R1127
C552 FB525 R609 R1128
IC8455 C8462 R1122 R1139
D1103
D1104
R8464
L503
R8462 R1138
R1120
D524
R3326
L501
L502
R640
C562
R641
R647
C589
C573
R649
FL516
R8461
R8463
R632
8
R3316
R3313
R3339
C585 C551
C582
IC507
IC504
D522
C588 FB532
FB2631
FB2630 R503
FB2629 R3338
R631
R624
R623
FB2628
R2601
C581
L504
C583
FB2627 C556
FB2626
FB2625 R2636 R604 R588
FB2624
C590
R589
FB2623 C567 R606 FB521
R2602
FB2622 Q2603
R2635
FB2621 R594 R593
C559
C563 FB529 C560
FL515
L2605
C572 Q506
R8469
C561
C555
R616
Q508
R602
L2603
R617 FB531 C554
P2601
C575
IC503
R502
R592
R618 C558
C8458
C568
L2604
R3308
R622
C576
R619 R630 C553 R591 R590
R607
9
R596
IC8452 R586 FB522
L2602
Q509
Q505
R4449 Q507 R638
L2606
R615
C570
C3507
L2601
R612
R8466
R8465
R621
R614
IC505
R4450 C569
FB3301
R611
R4459 C574 R610
IC8451
R8454
C571
P3301
FB528 L3301
C8457
VA3302 VA3301
IC3501
R8452
C3306 FB3302
R581
R501
FB530
C3304
C3302
IC3301
R582
FL514
IC3303
R3310
R629
C3316
10
R3511
C3309
R3312
R3306
R3305
C550
FB3306
R584
R3356 C3401
R635
R3355 C3400
R3360 C3407 SG1533
R3502 R3507
SG1534 SG1535
R3359 C3406 LUG9608 LUG9605 SG1537 SG1536
6–2
R3506
IC3302
R3361 C3402 SG1538 SG1539
LUG9602
SC1505
C3371
R3505
SG1540
R3362 C3403
X3302
R3508
R1565
R3353 C3398
R3345 R3342 R3346

C3370
R3354 C3399
C1534
11
R1508
D1502
C3324 R3357 C3404

C3322
R3358 C3405
C3518
C3380
C3381 R3369
R2073 C3408 R3389 C3390 R3377
R3501
C3382 R3370
C3392 R3379
C3391 R3378
IC3502
SG1501
R3323
C3384 R3371
SG1504 SG1507
C3385 R3372
R3321 R3322
SG1513 SG1510
C3372
C3393
C3374
C3394
C3375
C3388
C3387
C3386
C3389 R3376 C3383
SG1516 SG1519
R3380
R3364
R3381
R3365
R3375
R3374
R3373
SC1501
D3501
R3512 SG1522
R3363 C3373
R1561
C3502
R3510
R3509
C3501
C1507
12
R1582
R1518
C3305
D1505
C3307
R1583
R1521
R1524
C3503
D3301
R3331
R1514
R1584 R1527
R1541 R1516 R1543
R1539
C1531
R3330
R3311
R1559
Q1508
FB1512
C3325
C3327
C3326
R1509
FB3304
R3309
R1558
Q1509
C3331
FL3303
C3330
C3328
R1537 R1536
C3301 R1573
IC1504
FB9607 R1572
R1571
FB526
R1570
R1569
R1568 C566
C3303 R1567
R605
R1566
FL3501
R603
P9601
13
SG1523
SG1524
C9654 R601
C565
SG1520 SG1517
SG1511 SG1514
SG1508 SG1505
SG1502
SG1521 SG1518
SG1512 SG1515
SG1509 SG1506
SG1503
R600
FB524
SC1502 SC1503
R595
R597
R9656 R9658 R9657
14
C9652
IC9610
R549 R598
R627
R628
R533
R522 R625
IC509
R547
R538 R599 FL517
D507
D508
FB504
FB505
FB506
FB507
D509
D510
C9646
D512
C510
R523
R517
R511
FB502
D515
C501
C9641 IC9606 R551
L9606
D9612
C521
C9638
R514
R524
C508
FB9605
R512
FB503
IC501
15
C502 R4406
C9640
R4417
R4444
R585
R587
R583
FL501
FL502
FL503
FB533
FB534
FB535
LUG9607
R4443
R505
R506
R507
R637
R633
R636
R4440
R4439
R4442
R4401
C4425
R4402
X4401
R4452 R4451
16
C4414
C9639
IC4405
R4403
C4424
FB9604 IC9605
D9611
L9602 R2612
C9631
R4433
R4458
P2603
C9634
R2607 R2606
R2605
R4432
R4461
C9651
FB9606
R2611
IC9608
D9613
C9647 L9604
R1501
R4431
C9649
17
SG1525
R4448
R9676
SG1530 SG1531
SG1532
SG1526 SG1527
SG1529 SG1528
IC9601
R9675
C9613
R9664
R9665
R9685
R9669
R9666
SC1504
LUG9603
P9602
LUG9606
18
19
LC-52DH77E/RU/S
LC-52DH77E/RU/S
MAIN Unit (Side-B)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
6–3

LC-52DH77E/RU/S
19
18
R2067 R2075
R2069
R2017
Q2002
17
C2003 R2007
IC2001
C2002
R1121 C1153
C1154
16
R1118 C1145
R1124
R1117 R1123
R1135 R1119
L1103
Q503
C543 D517
Q1106 Q1107 D518 C544
C2703
R573
Q502
R572
R577
Q501
R2703
D519
C542 C545 R2711 C2702
Q504
D516
R2726 C2701
Q2701
R2702
R2704
R2705 R2707
D2701
D2707
R9633
R2719 R9621
C9612 R9632
C9619
R9620
R2709 C9610
C1105
15
C9609
C9615 R9634
C9607
R2019
R2031
C2017
C2018
R2015
IC2004
R2029
R2065
Q2005
R1131 C1104
R1104
R2066
C2021
C1109
IC2009
IC1101
R1103 R2002 C2020

C1107 R2078
R2084
R2013
R2061
R2076
R2035
R2021
R2038
C2007
R2060
R9681 R2005
R2018
14
R2058
IC2003 R2028
C1117
IC2006
IC2008
C2010
C1115
C1116
IC1103 IC1104
R8453
R2604
C2001 R2026 C8455 R8455 R2640
R2044
C2013
C2026 R2016
R2048 R2027
C1159 R2638
Q2003
C1120 R2037
R2039
R2637
L1102
R2056
C1126
R2059
C2022
C1128
R2040
R2085 Q2004 R2613 R2634
R2023
R1132
IC2005
D2007 R2054 R2024 R2620 R2633
C2030 IC2010
R8451
C1127 R2632
C2006
C1135
C1136
D2001
R2630
R2639
C1137
D1105 R2052
C1134
C1144 C1139
C1142 IC8401
C1143
C1146
C1149
C1150
R9683
Q1105
R8476 R8477
13
R9682
C1158
R1130
D8454
C8468
R8482 R8483
C1157
C1151
C8469
C1152
R8478
IC8454 D8457
R8481
C586
C584 C580 D8455

C1155 C1156
C8470
R8479
C8471
D8456 R9326
R1137
R1125
C8456
R8459 R8458
C579
R1136
IC506
R620
R2603
C578 C8452 R2629
R2628
R8456
R8457
R2627
C577 R2626
IC8402
C8453 R2625
R8474 R3388 R2624
R2623
C8451 R2621
R2619
R2618
12
R2617
R2615
R2616
R3387
R3314
R4422
D527
R4409
R4419
R4416
R643
R4408
R4463
R4407 R4460
R4462 R4464
R8468
R8467
R4425
R4426
D530
R4415
R4423
R4410
R4437
R644
R4414
R642
R4411
C3514
C3506 C3504
C3505
D526
C3508
C3509
11
C3512
C3510
C3511
R4413
R3349 R3350
C3513
C3347
R3343 R3344
R3347 R3348
C3320 R3320 R3319 C3332
C3317
R3324
R3303
R3304
6–4
R3325
C3353
C3351
R3340
R3301
R3302
C3336
C3333
D3329
C3349
C3368
R3317
R3318
R3341 X3301
R3328 C3369
D3324 C3350
FB3307
C3358
D3320
R3334 C3360 C3362 C3365

C3366 C3311
C3339
R3503
D3314 C3363 C3314
C3344
R3504
10
D3325
C3312
C3361 C3352
C3341
C3338
C3334
D3328
C3343
C3348
C3340 C3313
C3345
D3303
R3327
D3309 C3367
C3356 C3359
R3337
R3332
R3333
C3354
R1510 D3319 C3364 R3335
R3336 C3329
C3337
D3326
D1516 C3342
D1517
D3310
C3357
R9684
C3355
D3313 C3346 R3307
C3335
D3318 C3519
C3516
D3305
R3351
R3352
D3327 R3329 C3520
D3307
D3323
C3521
9
D3315
C3522
R1532 D3306
D3317
R1546 C1530 C1529 D3316 D3308 C3517
C3523
C3515
C1528
Q1506 Q1504 C3524
R1529
FB3308
D3321 D3311 D3304 D3312
R1548 R1513
R1528 C1527
D3322
R1530
Q1507
R1549 Q1505
R1560
D1511
R3382 C3395
R3366 C3376
R3367 C3377
R3383 C3396
R3368 C3379
R3384 C3397
D1510 R1564
C3378
D1527
R1551
C1520
C1524
R1555 C1523
R1550
R1556
C9666
R9605
R1552
FB9608
C1525 C9603
R1554
R1553
C1522
8
C1519
R1542
D1530
D1529
Q9608
R3386
C3321 D9616
R3385
R3315
R1517 C1518 C1517
C3323
C1516 C1515
FL3302
FL3301
C1514
Q9610
D1526
R1531
C1511
C1512
C3319 D9615
R9670
R9671
R9672
R9673
C3318 C3308
R1557 C1513 C1510
R1581
R1580
R1577
R1576
C3315 C3310
FB3305
FB3303
R1579
R1578
R1575
R1574
R1526
R1507
D1512
C9656
C9658
C9648
C9650
D9614
IC9609
7
C9660
R1512
C1509
R1511
R9601
C9644

D1501
R9602
C9662
C1508
D1504 D1503
R9623
R1506 D1507 R1505 D1506
R1504 R1503
D1509
R1519
D1508
R1522
C9608
IC9603
C9604
D9609 R9624 D9608
6
R9643
R9629
R9631
R9610
C9627 R9639
C9636
C9632
C9618
Q9602
C9601
C9620
Q9601
D9601
C9616 C9629 R9641
C9602
C4423
R4405 D9607 R9617
D9606
R4446
R9607
5
Q9604
R9686
R4447
R9645 R9646
FB4403
R4434 R4454 R9615
R9616 Q9609
C4413
R4453
R4455
R4457
R4436 C9637
D9604 R9613 D9605
R9626 R9614
Q9607
IC4404
R4427
C4402
C4416
C4415 R9636 IC9607
R4428 C9606
R9628
R9625
R9622
C4410
C4411
FB4404 C9605 R9630 R9642 R9649
C4417
C4404
R9635
C9624
C9628
R9647
C4412 FB4402
C4401
C4403
C9617 R9644
FB9601
IC9602
R4435 R4456
R4424
R4412 C9614
C4420 C4418
C4426
R9619
R4420 C4405 C9611
C4419 C9626 R9637
4
C4421
R2608
C4409
R4465
R4441
R9651
R9650
R4438 D9603 R9612 D9602 R9638
R9640
R4429
MAIN Unit (Chip Parts Side-B)
C9642 R9648
C9645
R4418
D1523
R4430 D1525
C9635
R4421
R1535
C9633
R4445
FB4401
C9630 C9643 R9652
D1524 D1521 D1522
FB4405
R4404
C1526
R1547
C4422
R1545
IC1505
C1521 R1544
FB1504
FB1506
FB1507
FB1508
FB1509
FB1510
3
R1538
D1528
R1540
C9663
C9659
C9657
C9655
2
1
G
A
H
C
E
F
J
I
LC-52DH77E/RU/S
[2] LED UNIT PRINTED WIRING BOARD
LED Unit (Side-A) LED Unit (Chip Parts Side-A) LED Unit (Side-B)
J
R106
I
P102
H
P101
G
R105
D102
Q102
R103
F
Q104
R116
R114
R115
D103
Q105
R110
Q103
R107
E
R113
C102
IC101
R109
D104
C101
B
R120
C104
C103
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
6–5

LC-52DH77E/RU/S
[3] KEY UNIT PRINTED WIRING BOARD
I
KEY Unit (Side-A)
KEY Unit (Chip Parts Side-A)

E
R154 D155
R153
S153
S155
S151
S152
S156
S157
S154
D152
D151
R151
D R152 P151
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
6–6

LC-52DH77E/RU/S
CHAPTER 7. SCHEMATIC DIAGRAM
LC52DH77E
Service Manual
[1] DESCRIPTION OF SCHEMATIC DIAGRAM

VOLTAGE MEASUREMENT CONDITION:
1. The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 220-240V.
Signals are fed by a colour bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester.
INDICATION OF RESISTOR & CAPACITOR:

RESISTOR
1. The unit of resistance “Ω” is omitted.
(K=kΩ=1000 Ω, M=MΩ).
2. All resistors are ± 5%, unless otherwise noted.
(K= ± 10%, F= ± 1%, D= ± 0.5%)
3. All resistors are 1/16W, unless otherwise noted.
CAPACITOR
1. All capacitors are µF, unless otherwise noted.
(P=pF=µµF).
2. All capacitors are 50V, unless otherwise noted.
CAUTION:
This circuit diagram is original one, therefore there may be a
slight difference from yours.
SAFETY NOTES:
1. DISCONNECT THE AC PLUG FROM THE AC
OUTLET BEFORE REPLACING PARTS.
2. SEMICONDUCTOR HEAT SINKS SHOULD BE
REGARDED AS POTENTIAL SHOCK HAZARDS
WHEN THE CHASSIS IS OPERATING.
IMPORTANT SAFETY NOTICE:

PARTS MARKED WITH “ ”( ) ARE
IMPORTANT FOR MAINTAINING THE SAFETY OF THE
SET. BE SURE TO REPLACE THESE PARTS WITH
SPECIFIED ONES FOR MAINTAINING THE SAFETY AND
PERFORMANCE OF THE SET.
7–1

LC-52DH77E/RU/S
[2] SCHEMATIC DIAGRAM
MAIN Unit-1
AND SHADED COMPONENTS=SAFETY RELATED PARTS
J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7–2

LC-52DH77E/RU/S
MAIN Unit-2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7–3

LC-52DH77E/RU/S
MAIN Unit-3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7–4

LC-52DH77E/RU/S
MAIN Unit-4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7–5

LC-52DH77E/RU/S
MAIN Unit-5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7–6

LC-52DH77E/RU/S
MAIN Unit-6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7–7

LC-52DH77E/RU/S
MAIN Unit-7
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7–8

LC-52DH77E/RU/S
MAIN Unit-8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7–9

LC-52DH77E/RU/S
MAIN Unit-9
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 – 10

LC-52DH77E/RU/S
MAIN Unit-10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 – 11

LC-52DH77E/RU/S
MAIN Unit-11
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 – 12

LC-52DH77E/RU/S
LED Unit LED

J
DUNTKF096WE
I RMC101
UA053WJ
IR RECEIVER MODULE
H
OUT GND VCC SLD101
PSLDPA076WJFW
1 2 3
P102 3.3
NA330WJ R106
22K
To MAIN RA
BU+3.3V 1
Q104 R120
OPC+3.3V 2 R116 2SC3928AR 100
G 27K LED CONT C103 D104 C104

GND 3 100u EXA092WJ 2.2u
D103 0.7 16V 16V
12V
R/C 4 PX0421CE ASY
TVF
TV POW R114
POWG_LED 5 G/B 160 0.2 0
1 3
POWR_LED 6
R 2.3 0
LED_OPC 7 2 4
R115
820
OPC 8 Q105
R107 2SC3928AR 0
LED_YOYAKU 9 39K LED CONT
F
LED_5V 10
R110 0
10K
0.7 Q103
2SC3928AR
LED CONT
0
C101
0.01u 3.3
1 4
GND VCC
IC101
D GA1S100W
OPC
GND Io
2 3
R113 C102
0 10u
16V
C ASX
OPC
D102
B PX0421CE
G
3 1
R103
160 4 2
R105
2.5
10K
Q102 0
1 2
2SC3928AR
LED DRIVER
3 4
0
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 – 13

LC-52DH77E/RU/S
KEY Unit
J
KEY
CH-UP CH-DOWN INPUT VOL-UP VOL-DOWN

S151 S152 S153 S154 S155 MENU
K0003AJ K0003AJ K0003AJ K0003AJ K0003AJ S156
K0003AJ
3.3 3.3
D151 D152
EX0646GE EX0646GE
0.0 0.0
G
P151
NA059WJ
R151 R152
TO LCD CONT KM 8.2K 12K
1/8W 1/8W R153 R154
KEY1 1 8.2K 12K
F 1/8W 1/8W
KEY2 2
POW
S157
STBY_POW 3 K0003AJ
NC 4
GND 5
E 3.3
D155
EX0646GE
0.0
KEY UNIT
DUNTKE266WE01
(QPWBFE266WJ)
B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
7 – 14

LC-52DH77E/RU/S
—MEMO—
7 – 15

PartsGuide
LC-52DH77E/RU/S
PARTS GUIDE
No. S49Z2LC52D77E
LCD COLOUR TELEVISION
MODELS LC-52DH77E/RU/S
CONTENTS
[1] PRINTED WIRING BOARD [6] CABINET AND MECHANICAL

ASSEMBLIES PARTS
[2] LCD PANEL [7] LCD PANEL MODULE Assembly
[3] DUNTKF190FM01 (MAIN Unit) [8] SUPPLIED ACCESSORIES
[4] DUNTKF096FM04 (LED Unit) [9] PACKING PARTS

(NOT REPLACEMENT ITEM)
[5] DUNTKE266FM17 (KEY Unit)
[10] SERVICE JIGS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used

for after sales service only.
The contents are subject to change without notice.
LC-52DH77E/RU/S
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[1] PRINTED WIRING BOARD ASSEMBLIES

N DUNTKF190FM01 N P MAIN Unit
N DUNTKF096FM04 N P LED Unit
N DUNTKE266FM17 N P KEY Unit
! N RDENCA308WJQZ BR P POWER Unit (Unit Replacement Item)
N CPWBX4151TPXZ J C-PWB (LCD Control Unit)
N RUNTKA528WJZZ BF J Inverter Unit-1
N RUNTKA529WJZZ BF J Inverter Unit-2
N RUNTKA530WJZZ AP J GND-PWB (INVERTER GND Unit-1)
N RUNTKA531WJZZ AP J GND-PWB (INVERTER GND Unit-2)
! TU1101 RTUDAA019WJQZ AZ J TUNER Unit
[2] LCD PANEL
N R1LK520D3LW80Y EB N P 52" LCD Panel Module
[3] DUNTKF190FM01 (MAIN Unit)
C501 VCKYCZ1HB221KY AA J Capacitor 220p 50V Ceramic
C503 VCCCCZ1HH101JY AB J Capacitor 100p 50V Ceramic
C508 VCKYCZ1HB102KY AB J Capacitor 1000p 50V Ceramic
C521 VCKYCZ1EF104ZY AA J Capacitor 0.1 25V Ceramic
C534 RC-KZA510WJPZY AB J Capacitor 10 16V Ceramic
C550 VCCCCZ1HH100DY AB J Capacitor 10p 50V Ceramic
C551 VCERMZ1CN477MY AE J Capacitor 470 16V Capacitor(AL)
C565 VCKYCZ1EB472KY AB J Capacitor 4700p 25V Ceramic
C567 VCEASY1EN107MY AC J Capacitor 100 25V Electrolytic
C569 VCKYCY1AB105KY AB J Capacitor 1 10V Ceramic
C570 RC-KZA067WJZZY AB J Capacitor 4.7 10V Ceramic
C577 RC-KZA616WJQZY AB J Capacitor 10 10V Ceramic
2
LC-52DH77E/RU/S
RANK MARK DELIVERY

C592 VCKYCZ1AB104KY AB J Capacitor 0.1 10V Ceramic
C1101 VCKYCZ1EB103KY AA J Capacitor 0.01 25V Ceramic
C1103 VCERML1CN107MY AC J Capacitor 100 16V Capacitor(AL)
C1113 VCERMZ1CN477MY AE J Capacitor 470 16V Capacitor(AL)
C1119 RC-KZA114WJZZY AB J Capacitor 1 25V Ceramic
C1519 RC-KZA520WJQZY AA J Capacitor 10 10V Ceramic
C2718 VCKYTV1EB474KY AC J Capacitor 0.47 25V Ceramic
3
LC-52DH77E/RU/S
RANK MARK DELIVERY

C3378 VCKYCY1HB472KY AA J Capacitor 4700p 50V Ceramic
4
LC-52DH77E/RU/S
RANK MARK DELIVERY

C3503 VCAAPE0JJ107MY AE J Capacitor 100 6.3V Electrolytic
C3511 RC-KZA576WJQZY AB J Capacitor 0.22 6.3V Ceramic
C4414 VCAAPD1AJ686MY AE J Capacitor 68 10V Electrolytic
C4424 VCCCCZ1HH8R0DY AA J Capacitor 80p 50V Ceramic
C4425 VCCCCZ1HH8R0DY AA J Capacitor 80p 50V Ceramic
C9612 VCKYCZ1CB223KY AC J Capacitor 0.022 16V Ceramic
C9622 RC-KZA383WJZZY AC J Capacitor 10 25V Ceramic
5
LC-52DH77E/RU/S
RANK MARK DELIVERY

C9654 VCAAPD1DJ476MY AF J Capacitor 47 20V Electrolytic
D504 RH-EXA512WJZZY AB J Diode MAZ8039GHL
D505 RH-EXA554WJZZY AB J Diode MAZ8150GML
D512 VHDKDS184//-1Y AB J Diode KDS184-RTK/P
D516 RH-EXA535WJZZY AM J Diode MAZ8082GML
D520 VHPGPFSV51V-1 AG J Diode Photodiode
D523 VHDMAZ9120H-1Y AC J Diode MAZ91200H0L
D524 VHDMAZ9120H-1Y AC J Diode MAZ91200H0L
D525 RH-EX0259TAZZY AB J Diode PDZ5.6B,115
D1102 VHDMA111G++-1Y AA J Diode MA2J1110GL
D1512 VHDRB520S30-1Y AC J Diode RB520S-30TE61
D2003 RH-PXA018WJZZY AC J Diode GM1HD55200A
D3301 RH-PXA018WJZZY AC J Diode GM1HD55200A
D3304 VHD1SS226//-1Y AC J Diode 1SS226(T5L,F,T)
6
LC-52DH77E/RU/S
RANK MARK DELIVERY

D8457 VHD1PS184++-1Y AB J Diode 1PS184,115
D9610 VHDRB056L40-1Y AC J Diode RB056L-40TE25
E3301 PRDARA577WJFW AF J Battery Heat Sink
FB501 RBLN-0077TAZZY AB J Ferrite Bead
FB504 RBLN-0061TAZZY AD J Ferrite Bead
FB1512 RBLN-A375WJQZY AA J Ferrite Bead
FB2001 RBLN-A188WJZZY AA J Ferrite Bead
FL501 RFiLN0003TAZZY AD J Filter
FL504 RFiLN0017TAZZY AC J Filter
7
LC-52DH77E/RU/S
RANK MARK DELIVERY

FL3301 RFiLNA119WJZZY AC J Filter
IC501 RH-iXC697WJQZS AG J IC BR24C21F-E2
IC503 VHiT7SET08U1EY AC J IC TC7SET08FU(5L,JF,T
IC504 VHiMM1506XN-1Y AD J IC MM1506XNRE
IC506 VHiM3221EiP-1Y AK J IC MAX3221EIPower
IC507 VHiMM1507XN-1Y AD J IC MM1507XNRE
IC1105 VHiPQ1KA503-1Y AD J IC PQ1KA503MZPH
IC1501 RH-iXC697WJQZS AH J IC EDID PC
IC1504 VHiSii91873-1Q N J IC SiI9187ACNU
IC2001 VHiS80927NM-1Y AC J IC S-80927CNMC-G8XT2G
IC2002 RH-iXC786WJN1Q AM N J IC R5F364A6NFB (Monitor Micon)
IC2003 VHiTC7WH125-1Y AD J IC TC7WH125FK(TE85L,F)
IC2004 VHiS24CS08J-1Y AE J IC S-24CS08AFJ-TB-1G
IC2005 VHiLCX125FT-1Y AD J IC TC74LCX125FT(EL,K)
IC2006 VHiTCVHC32T-1Y AE J IC TC74VHC32FT(EL)
IC2007 VHiAHC1G08W-1Y AD J IC 74AHC1G08GW/G,125
IC2008 VHi7WH126FU-1Y AE J IC TC7WH126FU(TE12L,F)
IC2009 VHiTC7SH00U-1Y AC J IC TC7SH00FU(T5L,JF,T
IC2601 VHiHC2G66DP-1Y AD J IC 74HC2G66DP,125
IC2701 VHiYDA148QZ-1Y AL J IC YDA148-QZE2
IC3301 VHiBD6538G+-1Y AD J IC BD6538G-TR
IC3302 RH-iXC773WJQZQ N J IC MT5391UHMJ
IC3501 RH-iXC790WJQZQ N J IC K4T1G164QE-HCF8
IC3502 RH-iXC790WJQZQ N J IC K4T1G164QE-HCF8
IC4404 VHiAOZ1320C-1Y AE J IC AOZ1320CI-04
IC4405 VHiMT8295AE-1Q AM N P IC MT8295AE
IC8401 RH-iXC721WJQZQ AR J IC HY27US08121B-TPCB
IC8451 VHi7WH126FU-1Y AE J IC TC7WH126FU(TE12L,F)
IC8452 VHiLCX157FT-1Y AD J IC TC74LCX157FT(EKJ)
IC8454 VHiAHC1G08W-1Y AD J IC 74AHC1G08GW/G,125
IC8455 VHiBR24S64F-1Y AF J IC BR24S64F-WE2
IC9601 VHiHC2G66DP-1Y AD J IC 74HC2G66DP,125
IC9603 VHiMM3141YN-1Y AC J IC MM3141YNRE
IC9605 VHiLV5893M+-1Y AE J IC LV5893M-TE-L-E
IC9608 VHiLV5893M+-1Y AE J IC LV5893M-TE-L-E
IC9609 VHiTCR5SB33-1Y AC J IC TCR5SB33(TE85L,F)
IC9610 VHiPQ1LAX95-1Y AD J IC PQ1LAX95MSPQ
J501 QJAKJ0008GEZZ AD J Jack
J502 QJAKFA061WJZZ AE J Jack
J503 QJAKGA131WJZZ AG J Jack
J504 QJAKJ0047CEZZ AD J Jack
J505 QJAKGA079WJZZ AD J Jack
J506 QJAKFA061WJZZ AE J Jack
J3301 QSOCZA172WJQZ AD J Jack
L502 VPCNN120J1R9NY AB J Peaking 12µH
L1101 VPSBN100J1R2NY AB J Peaking 10µH
L1103 VPSBN2R2JR54NY AB J Peaking 2.2µH
L1104 VPSBN2R2JR54NY AB J Peaking 2.2µH
L2601 RCiLFA119WJZZY AE J Coil
L2701 RCiLPA899WJZZY AC J Coil
L3301 RCiLFA228WJZZY AD J Coil
L9605 RCiLPA758WJQZY AC J Coil
L9606 RCiLPA759WJQZY AD J Coil
LUG9601 QLUGHA009WJZZY AC J Lug
P2001 QPLGN0064CEZZY AE J Plug
P2002 QPLGNA324WJZZY AC J Plug
8
LC-52DH77E/RU/S
RANK MARK DELIVERY

P2003 QPLGNA330WJZZY AD J Plug
P2601 QCNCWA671WJQZY AH J Plug
P2603 QPLGNA144WJZZY AF J Plug
Q501 VSiMH23T110-1Y AC J Transistor IMH23T110
Q503 VS2SA1530AR-1Y AB J Transistor 2SA1530A-T112-1R
Q505 VSLTC144EEB-1Y AA J Transistor LTC144EEBFS8TL
Q1101 RH-TXA026WJZZY AD J Transistor PBLS2001D,115
Q1102 VSLTA124EEB-1Y AA J Transistor LTA124EEBFS8TL
Q1104 VS2SC3928AR-1Y AB J Transistor 2SC3928A-T112-1R
Q1508 VSKTA1535T+-1Y AC J Transistor KTA1535T-RTK/P
Q1509 VSKRC402E++-1Y AB J Transistor
Q2003 VSRT1P141U/-1Y AB J Transistor RT1P141U-T111-1
Q2004 VSRT1N141U/-1Y AB J Transistor RT1N141U-T111-1
Q2005 VSRN1102///-1Y AB J Transistor RN1102(TE85L,F)
Q2006 VSRT1N141U/-1Y AB J Transistor RT1N141U-T111-1
Q2701 VSDTC614TK+-1Y AB J Transistor DTC614TKT146
Q9604 RH-TXA026WJZZY AD J Transistor PBLS2001D,115
Q9610 VSRSS050P03-1Y AG J Transistor RSS050P03TB
R504 VRS-CZ1JF103FY AB J Resistor 10k 1/16W Metal Oxide
R505 VRS-TQ2EF750JY AA J Resistor 75 1/4W Metal Oxide
R508 VRS-CZ1JF333FY AA J Resistor 33k 1/16W Metal Oxide
R511 VRS-CZ1JF102JY AA J Resistor 1k 1/16W Metal Oxide
R522 VRS-CZ1JF221JY AA J Resistor 220 1/16W Metal Oxide
R538 VRK-SA1JF472JY AA J Resistor 4.7k 1/16W Metal Composition
R547 VRS-CG1JF101JY AA J Resistor 100 1/16W Metal Oxide
R552 VRS-TV1JD221JY AA J Resistor 220 1/10W Metal Oxide
R566 VRS-CZ1JF564JY AB J Resistor 560k 1/16W Metal Oxide
9
LC-52DH77E/RU/S
RANK MARK DELIVERY

R572 VRK-SA1JF331JY AA J Resistor 330 1/16W Metal Composition
R573 VRK-SA1JF331JY AA J Resistor 330 1/16W Metal Composition
R582 VRS-CZ1JF472JY AA J Resistor 4.7k 1/16W Metal Oxide
R590 VRS-TW2ED101JY AA J Resistor 100 1/4W Metal Oxide
R601 VRS-CY1JF000JY AA J Resistor 0 1/16W Metal Oxide
R1126 VRK-SA1JF000JY AB J Resistor 0 1/16W Metal Composition
R1129 VRK-SA1JF222JY AB J Resistor 2.2k 1/16W Metal Composition
R1511 VRK-SA1JF473JY AC J Resistor 47k 1/16W Metal Composition
10
LC-52DH77E/RU/S
RANK MARK DELIVERY

R2012 VRS-CH1JF103JY AA J Resistor 10k 1/16W Metal Oxide
R2031 VRK-SA1JF103JY AB J Resistor 10k 1/16W Metal Composition
R2036 VRS-CZ1JF105JY AA J Resistor 1M 1/16W Metal Oxide
R2045 VRS-CY1JF106JY AA J Resistor 10M 1/16W Metal Oxide
R2049 VRS-CZ1JF272FY AA J Resistor 2.7k 1/16W Metal Oxide
R2053 VRS-CY1JF394FY AA J Resistor 390k 1/16W Metal Oxide
11
LC-52DH77E/RU/S
RANK MARK DELIVERY

R2080 VRS-TV1JD123JY AA J Resistor 12k 1/10W Metal Oxide
R2081 VRS-TV1JD822JY AA J Resistor 8.2k 1/10W Metal Oxide
R2082 VRS-TV1JD123JY AA J Resistor 12k 1/10W Metal Oxide
R2083 VRS-TV1JD822JY AA J Resistor 8.2k 1/10W Metal Oxide
R2601 VRK-SB1FF223JY AA J Resistor 22k 1/32W Metal Composition
R2602 VRK-SB1FF223JY AA J Resistor 22k 1/32W Metal Composition
R2608 VRK-SB1FF102JY AC J Resistor 1k 1/32W Metal Composition
R2725 VRS-TQ2EF000JY AB J Resistor 0 1/4W Metal Oxide
R3328 VRK-SA1JF222JY AB J Resistor 2.2k 1/16W Metal Composition
12
LC-52DH77E/RU/S
RANK MARK DELIVERY

R3363 VRS-CZ1JF680JY AB J Resistor 68 1/16W Metal Oxide
R3503 VRK-SB1FF100JY AA J Resistor 10 1/32W Metal Composition
R4408 VRS-CG1JF000JY AB J Resistor 0 1/16W Metal Oxide
13
LC-52DH77E/RU/S
RANK MARK DELIVERY

R8469 VRK-SB1FF472JY AA J Resistor 4.7k 1/32W Metal Composition
R9634 VRS-CZ1JF3R9JY AA J Resistor 3.9 1/16W Metal Oxide
R9641 VRS-CZ1JF3R9JY AA J Resistor 3.9 1/16W Metal Oxide
S2001 QSW-KA037WJZZY AC J Switch
14
LC-52DH77E/RU/S
RANK MARK DELIVERY

SC501 QSOCNA716WJZZ AM J Socket
SC502 QSOCZA161WJZZ AG J Socket
SC503 QSOCZA161WJZZ AG J Socket
SC504 QSOCNA715WJZZ AL J Socket
SC1501 QSOCZA072WJZZQ AH J Socket
SC1502 QSOCZA171WJZZY AF J Socket
SC1503 QSOCZA171WJZZY AF J Socket
TH2001 VHHM1103J03-1Y AC J Thermistor
! TU1101 RTUDAA019WJQZ AZ J Tuner
VA501 RH-VXA005WJZZY AA J Varistor AVR-M1005C270MTABBG
VA3301 RH-VXA074WJZZY AB J Varistor AVRL101A1R1NTB
VA3302 RH-VXA074WJZZY AB J Varistor AVRL101A1R1NTB
X2001 RCRSC0032TAZZY AG J Crystal
X2002 RFiLZA023WJQZY AD J Crystal Filter
X3302 RCRSCA101WJZZY AG J Crystal
X4401 RCRSCA101WJZZY AG J Crystal
N PCOVZA132WJKA N P Cover
[4] DUNTKF096FM04 (LED Unit)

C101 VCKYCY1HF103ZY AA J Capacitor 0.01 50V Ceramic
C102 VCEASX1CN106MY AC J Capacitor 10 16V Electrolytic
C103 VCEASY1CN107MY AC J Capacitor 100 16V Electrolytic
C104 VCKYTV1CF225ZY AB J Capacitor 2.2 16V Ceramic
D102 RH-PX0421CEZZY AD J Diode CL-165HR/YG-D-T
D103 RH-PX0421CEZZY AD J Diode CL-165HR/YG-D-T
D104 RH-EXA092WJZZY AB J Diode UDZSFVTE-1712B
IC101 VHiGA1S100W-1Y AE J IC GA1A1S100WP
R105 VRS-CJ1JF103JY AA J Resistor 10k 1/16W Metal Oxide
R106 VRS-CY1JF223JY AA J Resistor 22k 1/16W Metal Oxide
RMC101 RRMCUA053WJZZ AE J Remote Receiver
SLD101 PSLDPA076WJFW AD J Shield Case Shield
[5] DUNTKE266FM17 (KEY Unit)
D151 RH-EX0646GEZZY AA J Diode MTZJT-7215B
P151 QPLGNA059WJZZ AC J Plug
R151 VRD-RA2BE822JY AA J Resistor 8.2k 1/8W Carbon
R152 VRD-RA2BE123JY AA J Resistor 12k 1/8W Carbon
R153 VRD-RA2BE822JY AA J Resistor 8.2k 1/8W Carbon
R154 VRD-RA2BE123JY AA J Resistor 12k 1/8W Carbon
S151 QSW-K0003AJZZ+ AB J Switch
15
LC-52DH77E/RU/S
[6] CABINET AND MECHANICAL PARTS
43
1
31
43
29
1-1
1-2
7 32
1-2-2
1-2-1
1-3
20
3
34 1-4
3-1
1-2-3
3-2
1-2-4 40
4-3
42 4-2 40
4-1
4 4-2
4-1
5-3 4
5-2 4-3
41 8 5-1
5-3
15 5-2 9
11 5-1
5
10 5
14
40
15 40
9
41
12
39 41
24
41 14
21
39
41
13
39
13
12
27
40
36 38
2
23 40 17 38
18
16
17 33
22
40 35 6
19 2-1
6-1
2-2
28 6-2
37
26 36
30
40
25
16
LC-52DH77E/RU/S

RANK MARK DELIVERY
[6] CABINET AND MECHANICAL PARTS

1 CCABAC210WJ03 BR N P Front Cabinet Ass'y
1-1 Not Available - - Front Cabinet
1-2 Not Available - - Bottom Dec Ass'y
1-2-1 Not Available - N - Bottom Dec (A) Ass'y
1-2-2 Not Available - N - Bottom Dec (B) Ass'y
1-2-3 XEBSN40P10000 AB J Screw, x6 (DEC-A/B FIX)
1-2-4 HDECSA051WJ1A AS N J Shine Trim
1-3 Not Available - - LED Decoration
1-4 XEBSN40P10000 AB J Screw, x8 (CAB-A - DEC FIX)
2 CCABBB418WJ03 BP N P Back Cabinet Ass'y
2-1 Not Available - - Back Cabinet
2-2 Not Available - - Terminal Label
3 CCOVAC952WJ04 AL N P Control Cover Ass'y
3-1 Not Available - - Control Cover
3-2 Not Available - - Control Label
4 CANGKC100WJ01 AN P Vesa Angle Top Ass'y, x2
4-1 Not Available - N - Base Angle Top
4-2 Not Available - N - Vesa Angle
4-3 XHPS730P06WS0 AA J Screw
5 CANGKC101WJ01 AR P Vesa Angle Bottom Ass'y, x2
5-1 Not Available - N - Base Angle Bottom
5-2 Not Available - N - Vesa Angle
5-3 XHPS730P06WS0 AA J Screw
6 CCOVAD246WJ02 AM P Side AV Cover Ass'y
6-1 Not Available - N - Side AV Cover
6-2 Not Available - - Side AV Label
7 GCOVAD248WJ1A AH P Bottom Cover
8 LHLDWA133WJKZ AC J Wire Holder (CABLE)
9 LHLDWA143WJKZ AC J Wire Holder, x2
10 LHLDWA175WJUZ AC J Wire Holder, x4
11 LHLDZA934WJKZ AB J Power PWB Holder, x3
12 LHLDZB210WJ1A AE P Corner Lug (L), x2
13 LHLDZB211WJ1A AB P Corner Lug (S), x2
14 LHLDZB313WJ1A AC P Corner Lug (A), x2
15 LHLDZB325WJ1A AC P Corner Lug (B), x2
16 LX-BZA170WJF9 AB P Screw, x4 (CAB-B)
17 NSFTZA237WJFN AC J Shaft, x4 (D-SUB)
18 PSLDMB539WJFW AV P Full Shield
19 PSPAZC237WJKZ AH P Cooling Sheet
20 QCNW-H325WJQZ AF P Connecting Cord (KM)
21 QCNW-H333WJQZ AF P Connecting Cord (LA)
22 QCNW-H337WJQZ AL P Connecting Cord (PD)
23 QCNW-H340WJQZ AG P Connecting Cord (LB1)
24 QCNW-H341WJQZ AF P Connecting Cord (LB2)
25 QCNW-H958WJQZ AG P Connecting Cord (RA)
26 QCNW-H960WJQZ AG P Connecting Cord (LP)
27 QCNW-H973WJQZ AF P Connecting Cord (PL)
28 QCNW-H974WJQZ BF P Connecting Cord (LW)
29 QCNW-J553WJPZ AM N P Connecting Cord (SP)
30 QEARPA339WJFW AC P Earth Plate
31 RSP-ZA421WJZZ AS N P Speaker (L)
32 RSP-ZA422WJZZ AS N P Speaker (R)
33 TLABNC117WJZZ AA P Model Label
34 TLABZC085WJZZ AF P POP Label (for Europe)
34 TLABZC086WJZZ AF P POP Label (for Russia)
35 XBBS730P04000 AA J Screw (TUN/Shield)
36 XBPS830P06000 AA J Screw, x3 (HDMI)
37 XEBS930P08000 AA J Screw (21PIN)
38 XEBS940P16000 AB J Screw, x11 (CAB-B)
39 XEBSN40P10000 AB J Screw, x6 (LCD-Panel)
40 XHPS730P06WS0 AA J Screw, x30 (ANG/PWB FIX)
41 XHPS840P08WS0 AB J Screw, x10 (LCD-Panel)
42 TLABZB406WJZZ AA P EU ECO Label (for Europe)
43 PSPAKA423WJKZ P Spacer, x2
17
LC-52DH77E/RU/S
[7] LCD PANEL MODULE Assembly
33
22 21
17
25
1 26
15 27 24
14
18
28 32
28
23
4
16
6
7
3
31
19
5
20
12
13 9
29
10
13
29 11
2
30
18
LC-52DH77E/RU/S

RANK MARK DELIVERY
[7] LCD PANEL MODULE Assembly

1 R1LK520D3LW80Y EB N P LCD MODULE Ass'y
2 Not Available - - BEZEL Ass'y
3 CCHSMA554WJ01 J BL CHASSIS Ass'y
4 LHLDZA963WJKZ AB J HOLDER, x4
5 RLMPLA033WJN1 AR J LAMP, x18
6 QSOCFA003WJZZ AD J SOCKET, x18
7 CHLDZB353WJ01 AV J LAMP HOLDER UNIT
8 CHLDZB354WJ01 AV J LAMP HOLDER UNIT
9 PCOVUA158WJZZ BD J DIFFUSION PLATE
10 PSHEPA874WJZZ BB J LENS SHEET
11 CHLDZB343WJ01 J P CHASSIS UNIT
12 CHLDZB345WJ01 J P CHASSIS UNIT
13 CHLDZB382WJ02 J SHEET HOLDER UNIT, x2
14 CSLDMB528WJ01 J C-PWB COVER UNIT
15 PCOVWA061WJKZ AG J COVER
16 PCOVWA062WJKZ AG J COVER
17 RUNTKA528WJZZ BF J Inverter Unit-1
18 RUNTKA529WJZZ BF J Inverter Unit-2
19 RUNTKA530WJZZ AP J GND-PWB (INVERTER GND Unit-1)
20 RUNTKA531WJZZ AP J GND-PWB (INVERTER GND Unit-2)
21 QPWBM0566TPZZ AG J CS-FPC
22 QPWBM0574TPZZ AG J CS-FPC
23 CPWBX4151TPXZ J C-PWB (LCD Control Unit)
24 PSHEP2941TPZZ J HEAT RADIATION SHEET (for C-PWB)
25 PSPAZC235WJKZ AL J HEAT RADIATION SHEET (for C-PWB)
26 PSPAZC236WJKZ AL J HEAT RADIATION SHEET (for C-PWB)
27 RCORFA061WJZZ AG J FERRITE CORE, x2
28 XHPS830P06WS0 AA J SCREW, x10 (for fixing Inverter Unit x4, for fixing Cover x6)
29 LX-HZA039WJF7 AB J SCREW, x16 (for fixing Bezel Ass'y)
30 LX-HZA047WJF7 AB J SCREW, x2 (for fixing Bezel Ass'y)
31 LX-HZA046WJF7 AB J SCREW, x4 (for fixing GND-PWB)
32 LX-HZA045WJF7 AB J SCREW, x6 (for fixing C-PWB)
33 XHPS730P06WS0 AA J SCREW, x4 (for fixing C-PWB COVER)
19
LC-52DH77E/RU/S
[8] SUPPLIED ACCESSORIES
X4 X3 X2 X1
X1-1, X1-2, X1-3, X1-4
X8 , X9 , X10, X11
X12

RANK MARK DELIVERY
[8] SUPPLIED ACCESSORIES

X1 CDAi-A526WJ12 BP N P Stand Unit
X1-1 Not Available - - Support
X1-2 Not Available - N - Stand Base
X1-3 Not Available - N - Screw Ass'y
X1-4 Not Available - N - Tool for Stand
X2 LHLDWA173WJKZ AE J Cable Clamp
! X3 QACCKA047WJPZ AH N P AC Cord (except U.K. and Ireland)
! X3 QACCBA054WJPZ AN J AC Cord (for U.K. and Ireland)
X4 RRMCGA771WJSA AU P Remote Control Unit
X5 TCAUSA034WJZZ AA P Coution Sheet (for East Europe)
X6 TCAUZA222WJN1 AB P Class A Caution (for Europe)
X7 TCAUZA356WJN1 AA P Class A 22Language Caution
X8 TiNS-D908WJN2 AM N P Operation Manual (for Europe except East Europe)
X9 TiNS-D910WJN2 AQ N P Operation Manual (for East Europe)
X10 TiNS-D909WJN2 AM N P Operation Manual (for Northern Europe)
X11 TiNS-D911WJN2 AF N P Operation Manual (for Russia)
X12 Not Available - - "AAA" Size Battery
X13 TGAN-B078WJZZ AB P Warranty Card (for East Europe)
X14 TGAN-A077WJZZ AE J Warranty Card (for Russia)
X15 TGAN-A801WJZZ AC P Warranty Card (for U.K. and Ireland)
X16 TGAN-B079WJZZ AB P Warranty Coupon (for East Europe)
X17 TGAN-A802WJZZ AB P Aquos Card Plan (for U.K. and Ireland)
20
LC-52DH77E/RU/S
[9] PACKING PARTS (NOT REPLACEMENT ITEM)
S3
S14
S4
S5
S6
S7
S8
S15
S10
S11
S9 S13
S10
S1
S10
S16
S10
S17
S2
S12
21
LC-52DH77E/RU/S

RANK MARK DELIVERY
[9] PACKING PARTS (NOT REPLACEMENT ITEM)

S1 SPAKCE924WJZZ - N - Packing Case
S2 SPAKCD539WJZZ - - Packing Case (Bottom)
S3 SPAKAA374WJZZ - - Cover Sheet
S4 SPAKFB706WJZZ - - Stand Case
S5 SPAKFB716WJZZ - - Paper Cover
S6 SPAKFB824WJZZ - N - Stand Pad
S7 SPAKPA780WJZZ - - Mirror Mat Base
S8 SPAKPA904WJZZ - - Mirror Mat Sup
S9 SPAKPB043WJZZ - - Polyethylene Bag
S10 SPAKXC282WJZZ - - Buffer material (Top/Bottom)
S11 SPAKXC283WJZZ - - Buffer material (Top Center)
S12 SPAKXC284WJZZ - - Buffer material (Bottom Center)
S13 SSAKAA009WJZZ - - Polyethylene Bag
S14 SSAKAA111WJZZ - - Polyethylene Bag
S15 SSAKHA052WJZZ - N - Screw Case
S16 TLABM5584BMZZ - - Case No Label
S17 TLABZC194WJZZ - - EU ECO Label (for Europe)
[10] SERVICE JIGS
N QCNW-G616WJQZ BK J Connecting Cord Main-LCD Control (LW)
N QCNW-H347WJQZ AY J Connecting Cord Main-LCD Control (LP)
N QCNW-H348WJQZ AW J Connecting Cord Main-LED (RA)
N QCNW-G440WJQZ AP J Connecting Cord Main-KEY (KM)
N QCNW-H184WJQZ AX J Connecting Cord Main-Power (PD)
N QCNW-G625WJQZ AP J Connecting Cord Main-Power (PL)
N QCNW-J104WJQZ AS J Connecting Cord Main-Power (LB1)
N QCNW-J105WJQZ AS J Connecting Cord Power-Inverter (LB2)
N QCNW-J106WJQZ AM J Connecting Cord Power-Inverter (LA)
22
LC-52DH77E/RU/S

LC-52DH77E/RU/S
COPYRIGHT © 2009 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No Part of this publication may be reproduced,

stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
May. 2009 CS Promotion Center
TQ2743-S SH. DS Yaita,Tochigi 329-2193, Japan

Service Manual: LCD Colour Television

Uploaded by

Copyright:

Available Formats

Service Manual: LCD Colour Television

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: LCD Colour Television

Uploaded by

Copyright:

Available Formats

TopPage

LCD COLOUR TELEVISION

CHAPTER 4. TROUBLESHOOTING TABLE

This document has been published to be used for

IMPORTANT SERVICE SAFETY PRECAUTION

F7000, F7001 (4A/250V)

Employing lead-free solder

Using lead-free wire solder

Part No. Description Code

End of life disposal

1. In the European Union

2. In other Countries outside the EU

B. Information on Disposal for Business Users

1. In the European Union

2. In other Countries outside the EU

The battery supplied with this product contains traces of Lead.

For Switzerland: The used battery is to be returned to the selling point.

52" LCD COLOUR TV,

Remote control unit

Remote control sensor OPC indicator

OPC sensor (Standby/On) indicator

Attaching the stand unit

Inserting the batteries

Note on disposing batteries:

Using the remote control unit

Cautions regarding the remote control unit

• Strange colour, light colour, or dark • Adjust the picture tone.

Cautions regarding use in high and low temperature environments

Information on the software license for this product

400.0 118.0 111.7

[1] REMOVING OF MAJOR PARTS

Back Cabinet Ass'y

Front Cabinet Ass'y

3. Remove the Speaker (L) 1 , (R) 2 .

Control Cover Ass'y

LED Unit Bottom Cover

2 Speaker (R) 1 Speaker (L)

LCD Control Unit

2. Remove the 7 lock screws 3 and detach the MAIN Unit.

Corner Lug (B)

Corner Lug (A) Corner Lug (B)

LCD Panel Module

Corner Lug (L) Corner Lug (L)

Corner Lug (S)

MAIN Unit POEWR Unit

2. Detach the Lens Sheet 3 and Diffusion Plate 4 .

5 Lamp Holder Unit

5 Lamp Holder Unit

[1] ADJUSTMENT PROCEDURE

2. Entering and exiting the adjustment process mode

Remote controller key Main unit key Function

(1) Present page / number of total pages (4) Inducing display

1/16 INPUT1 AUTO EURO 52E_DH77E

MAIN Version 1.00 (E 2008/**/** 1HDE2)

(6) Item name (7) Parameter

No. Description Display specification

Page Line Item Description Remarks (adjustment detail, etc.)

7. Lamp error detection

Table of contents of adjustment process mode Page 2/16

Employing lead-free solder

Using lead-free wire solder

MAIN Version 1.00 (E 2008// 1HDE2)