Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Jiffy Model J-2000

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

Jiffy® J-2000 Model Steamer

FEATURES
• Polymer outer housing unit for durability
• Lightweight, flexible hose
• Shatterproof water caddy
• Safety wiring feature temporarily turns the unit off should it
accidentally run dry
• Comfortable, easy-to-grip handle
• Removes wrinkles up to five times faster than conventional
ironing
• Easy-roll casters for mobility
• Numerous steam head attachments available
• Backed by Jiffy®'s renowned Customer Service--should your
steamer need repair, send it to us and we will repair and ship
the unit within 24 hours from its arrival to our plant

INCLUDES:

Check

Owner's
Rod Set Manual
(not included with
J-1 series) J-2000 Base Unit
From the library of: Superior Sewing Machine & Supply LLC
Jiffy® J-2000 Directions
1. Attach hose firmly with included assembly wrench,
which is magnetized and located on the bottom of the
unit. Assemble and attach hose hanger rod set. See
page 9 for assembly instructions.

2. Invert water caddy filled with distilled or tap water,


plug into proper voltage outlet, turn switch to lighted
Figure 1
ON position and you will have steam within minutes. Never
substitute the Jiffy®Steamer water caddy.

3. For easy operation, mount optional Ji~ Steamboard to door or wall to


hold clothing while steaming (figure #2). For hanging garments without
optional Ji~ Steamboard, simply install an eye screw
or nail to inside of a doorway or directly onto a wall or
you may use your steamer's rod set as shown in figure
3. Touch material lightly with steaming head and
wrinkles will vanish instantly. The combined touch of
the steaming head and the direct steam is very
important. Some articles can be steamed better from the
underneath side. Speed and efficiency is accomplished
with a little practice. Always steam with hose in an
upright position, so any condensation is free to flow
back into steamer. If steaming in a low position near
floor, straighten hose up and out frequently to keep
Figure 2
clear of condensation. DO NOT ALLOW STEAMER
TO RUN DRY.
4. Hang steam head in an upright position in the hose hanger
section when not in use and tum switch to OFF (figure #3).

5. Periodically, pour old water out of steamer to avoid


sediment buildup and maintain proper water level (figure
#4). Remove hard water deposits with
Ji~ Liquid Cleaner. Wipe water cup
Figure3
out with a hand towel. See page 28 for
complete cleaning instructions.

NOTE: No two water supplies have the same mineral


content. If your steamer begins to cut on and off during
normal use, the thermostat is indicating the heating unit
Figure 4
needs the sediment cleaned out.
From the library of: Superior Sewing Machine & Supply LLC
Jiffy® J-2000 Parts Diagram

'\.

'\.
9 I/ '
\
;' 10)'
! ,/

!
' ;
;
/ /.
i ;
i I
i ,/
/

"\
''
'
'
'
·-·-19 \
\ 25
~,,'',,,\ /\

;
i
i'

Should you ever need replacement parts for your J~ Steamer, you may
purchase them separately. Use this handy diagram and parts list to identify any
part you may need. Please include model and serial number when ordering.
From the library of: Superior Sewing Machine & Supply LLC
Jiff~ J-2000 Parts Diagram Key
Jiffy Steamer List
Key# Part# Part Description Price
1 1030 Rod Set and Nut Complete with Metal Studs $ 25.50
2 0035 Hook Section of Rod Set $ 6.50
3 0036 Middle Section of Rod Set $ 7.50
4 0037 Bottom Section of Rod Set $ 7.50
5 0043 Metal Threaded Cap Screw for Rod Set $ 1.50
6 0039 Metal Threaded Stud for Rod Sections $ 1.50
7 1031 1/2" Split Ring for Rod Set $ 0.50
8 1032 Rod Set Nut $ 6.00
9 0253 Plastic Steam Head/Handle Replacement Kit $ 22.00
10 0251 Plastic Head/Handle Hose Attachment Complete $ 50.00
0280 Hose Per Foot (Black in Color) $ 3.00
11 1100 J-2000 Plastic Housing Kit $ 58.00
12 1140 J-2000 Water Caddy Complete
with Check Valve Cap $ 28.00
13 1141 J-2000 Water Caddy Complete
with out Check Valve Cap $ 24.25
0027A Replacement Check Valve Cap $ 3.75
14 0004 Round Beauty Ring $ 0.75
15 1125 Green Lighted Contura Rocker Switch - 120 Volt $ 9.00
1126 Green Lighted Contura Rocker Switch - 230 Volt $ 9.00
16 0132 Cord Set (16/3 gauge) with Strain Relief $ 9.50
17 0146B Cord Strain Relief $ 1.50
18 0148 Internal Wire Set $ 9.00
1193 Heating Unit Kit (wiring included) for Models with Green
Lighted Contura Rocker Switch -120 Volt Cord Set and
4 1/2" Water Line $ 81.50
1194 Heating Unit Kit (wiring included) for Models with Green
Lighted Contura Rocker Switch - 230 Volt Cord Set and
4 1/2" Water Line $ 81.50
19 01618 Heating Unit Assembly (no wiring included) for
Models with Green Lighted Rocker Switch - 120 Volt
Cord Set and 4 1/2" Water Line $ 62.50
01628 Heating Unit Assembly (no wiring included) for
Models with Green Lighted Contura Rocker Switch -
230 Volt Cord Set and 4 1/2" Water Line $ 62.50
20 0030 Brass 90 Degree Elbow Joint $ 2.50
21 1130 3/8" x 1/4" Straight Brass Fitting for
Heating Element Housing $ 2.50
22 0187 Copper Tube(41/2" length) with Nuts and
Compression Rings $ 4.00
23 0160 L-290 Thermostat $ 8.00
24 0195 Fusible Link Clamp $ 1.50
25 0151 Fusible Link Wire with Insulated Lug $ 3.00
26 1120 Bottom Plate with Casters $ 18.00
27 0011 Bottom Plate Casters (Set of 4) $ 6.50
28 0010 Screws for Bottom Plate (4 Screws Total) $ 0.75
ACCESSORIES
29 1050 Jiffy Steamer Assembly Wrench $ 4.00
0254 Metal Head/Wood Handle Hose Attachment Complete $ 70.00
0256 Metal Head I Wood Handle Only $ 37.50
0262 Wig Hose Attachment $ 50.00
1062 Steam Cleaning "B" Brush Hose Attachment $ 50.00
1063 Brush Only for the "B" Hose Attachment $ 8.00
0898 Liquid Cleaner- 3 Ten (10) Ounce Bottles per Package' $ 15.00
From the library of: Superior Sewing Machine & Supply LLC
'Not Available for Export.
Jiffy® J-2000 Wiring Diagram

Caution:
Insure that the power
cord is unplugged from
the electrical outlet before
attempting to repair your
Jiff~ Steamer.

From the library of: Superior Sewing Machine & Supply LLC
Jiffy® J-2000 Wiring Instructions

Please note switch terminal numbers 2, 3, 5 and 6 indicated on


the enlarged switch diagram are marked on the actual switch.
Jiffy®Steamers manufactured before May 2000 are not
marked with the terminal switch numbers, but the terminal
blades are in the same location.

1. Insert cordset into housing and connect white neutral wire from cordset
bundle to terminal number 5 on the switch.
2. Connect blue wire from the right side of heating element to the right side
of the L-290 thermostat.
3. Insert brass heating unit into housing and tighten with 2 mounting screws.
Connect green ground wire (from cordset) to the nearer of the two mount-
ing screws.
4. Connect black positive wire from cordset to plastic connector on orange
fusible link wire.
5. Connect other end of orange fusible link to terminal number 2
on the switch.
6. Connect yellow wire from the left side of the thermostat to terminal
number 3 on the switch.
7. Connect white wire from the left side of the heater unit to terminal
number 6 on switch.
8. Insert one end of copper water line and compression ring into threaded
fitting at bottom of brass heating unit and tighten nut with a 518 " wrench.
9. Connect other end of water line with compression ring to 90 degree brass
elbow at bottom of water cup and tighten with a 51 " wrench. (Heating unit
8
may be loosened and adjusted for a better fit if necessary.)
10. Set steamer upright and place black plastic strain relief approximately
4 11 " from end of cord and insert into housing using pliers.
2
11. Secure bottom plate with four screws.
12. To avoid leakage, be sure and tighten hose (or hat nozzle) with wrench
before using steamer.

From the library of: Superior Sewing Machine & Supply LLC

You might also like