API-1000-12 Rev 0 PDF

API WELDING PROCEDURE SPECIFICATION
WPS: API 1000-12 REV. NO.: 0 PROCESS: SMAW DATE: 9/9/2004
API-1104 QUALIFIED RANGES

Diameter: 2.375” o.d. thru 12.75” o.d. Filler Metal Group: API Group 1
Thickness: 0.187” thru 0.750” Joint Type: Butt
Mate rial: Yield greater than 42 kip to – equal to or less than 65 kip
Positions: Fixed: X Rolled: N/A Progression: Down
NOTE: This WPS shall be used in conjunction with the applicable sections of the Los Alamos National
Laboratories Welding Standards Manual (GWS)
WELD JOINT: Type: Butt Class: Full Penetration
Joint Description: Open Butt single V- welded from one side only.
Sketch Number: See pg. 2 for typical sketch and bead sequence.
FILLER MATERIALS: API Group No.: 1 AWS Class: E-6010

SFA Class: 5.1 F No.: 3 Sizes (s): 1/8 5/32 5/32
Number of Beads: See pg. 2 for typical number and of beads
BASE MATERIALS: Spec: ASTM A53 or A 106 A/B to Spec: API 5L X42 /X52
Thickness Welded: 0.187” - 0.750” to 0.187” - 0.750”
Pipe Diame ter: 2.375” o.d. thru 12.75” o.d. pipe to Pipe Diameter 2.375” o.d. thru 12.75” o.d. pipe
ASME P No.: 1 Group: 1 to P No.: 1 Group: 1
POSITIONS: Fixed: X Rolled: N/A PWHT: Time @ º F Temp.: N/A

Progression: Down Temperature Range º F: N/A
PREHEAT: Minimum Temp º F: 70 GAS: Shielding: N/A Backing: N/A

NOTE: See time between passes. Composition: N/A
INTERPASS TEMP.: N/A Flow Rate: CFH N/A
ELECTRICAL CHARACTERISTICS:
Current: DC Polarity: EP Ranges Amps: See pg. 2
Trans fer Mode: N/A WFS/IPM: N/A Volts: See pg. 2
Electrode size and Type See pg. 2 Travel/IPM See pg. 2
MAX. TIME BETWEEN PASSES: 5 minutes between root pass and second pass.
Engineering Standards Manual - Welding Standards Manual - Volume 3 Welding Procedure Specifications
WPS No.: API-1000-12 Rev. No.: 0 Date: 9/9/2004
WELDING TECHNIQUE:
Line-Up Clamp: Optional, if used line-up clamp shall be left until 50% of root bead is complete.
Stringer or Weave Bead: (S) Y (W) Y Single Pass N/A Multi Pass Y
Cleaning and/or Grinding:
PROCEDURE QUALIFIED FOR: Charpy V Notch N/A NDTT N/A D.T. N/A
Maximum K/J Heat Input: N/A
JOINT SKETCH AND BEAD NUMBER AND SEQUENCE
37.5° Bevel
t thickness varies 0 – 3/32” land

1/16 – 3/32” gap
NOTE: Weld layers are representative only  actual number of passes and layer sequence may vary
due to variation in joint design, thickness and fit-up.
TYPICAL WELDING PARAMETERS

Pass Filler/ Electrode Travel Speed
Number Size Amps Volts in/min. Other
1 E-6010 1/8 70 -100 22 - 26 9 – 12”
2 E-6010 5/32 125 –132 22 - 26 9 – 13
3 E-6010 5/32 125 –132 22 - 26 9 – 13
4 E-6010 5/32 125 –132 22 - 26 9 – 13
5 E-6010 5/32 125 –132 22 - 26 9 – 13
6 E-6010 5/32 125 –132 22 - 26 9 – 13
7 E-6010 5/32 125 –132 22 - 26 9 – 13
8 E-6010 5/32 125 –132 22 - 26 9 – 13
PREPARED BY: Kelly Bingham DATE: 9/9/2004

Signature on File
APPROVED BY: Tobin Oruch DATE: 9/9/2004

Signature on File
API-1000-12 REV.: 0 PAGE 3 OF 3 DATE: 9/9/2004
API WELDING SPECIFICATION PROCEDURE
TEST PARAMETERS
Point Type: Full Penetration Single V Butt Diameter: 8.644” o.d.
Thickness: 0.322” wall Filler: 1/8” & 5/32” E-6010
Material: API 5L X42 /X52 to ASTM A53 Preheat: 70*F
Position: 5G Fixed Current: DCEP Amps: 70-125
Progression: Down Volts: 22-26
GUIDED BEND TESTS

No. Type Result No. Type Result
1. Face Accept no indications 5. N/A
2. Root Accept no indications 6. N/A
3. Face Accept no indications 7. N/A
4. Root Accept no indications 8. N/A
TENSILE TESTS
No. Specimen Area Applied Ultimate Character of failure and location
Type Sq./ in Load Tensile
1. Figure 4 .3051 23,619 77,408 Base metal cup and cone
2. Figure 4 .3213 23,232 72,305 Base metal cup and cone
3. N/A
4. N/A
NICK-BREAK TESTS
No. Type Remarks on Nick-Break tests
1. Figure 5 Acc. Break is clean.

2. Figure 5 Acc. Break is clean
3. N/A
4. N/A
Welders Name: Scott Simonich Z No.: 200360 Stamp: SC002
Tests Conducted By: Brett McNeil
We certify that the statements herein are correct and that the tests were conducted in accordance with
API-1104.
Authorized By: Kelly Bingham ___________________ Date: 10/30/03
Signature on File

API-1000-12 Rev 0 PDF

Uploaded by

Copyright:

Available Formats

API-1000-12 Rev 0 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

API-1000-12 Rev 0 PDF

Uploaded by

Copyright:

Available Formats

API WELDING PROCEDURE SPECIFICATION

WPS: API 1000-12 REV. NO.: 0 PROCESS: SMAW DATE: 9/9/2004

API-1104 QUALIFIED RANGES

FILLER MATERIALS: API Group No.: 1 AWS Class: E-6010

POSITIONS: Fixed: X Rolled: N/A PWHT: Time @ º F Temp.: N/A

PREHEAT: Minimum Temp º F: 70 GAS: Shielding: N/A Backing: N/A

Maximum K/J Heat Input: N/A

JOINT SKETCH AND BEAD NUMBER AND SEQUENCE

t thickness varies 0 – 3/32” land

TYPICAL WELDING PARAMETERS

PREPARED BY: Kelly Bingham DATE: 9/9/2004

APPROVED BY: Tobin Oruch DATE: 9/9/2004

API WELDING SPECIFICATION PROCEDURE

Point Type: Full Penetration Single V Butt Diameter: 8.644” o.d.

Thickness: 0.322” wall Filler: 1/8” & 5/32” E-6010

Material: API 5L X42 /X52 to ASTM A53 Preheat: 70*F

Position: 5G Fixed Current: DCEP Amps: 70-125

Progression: Down Volts: 22-26

GUIDED BEND TESTS

1. Figure 5 Acc. Break is clean.

You might also like