Ultrasonic Oxygen Sensor Module Gasboard7500E

Ultrasonic Oxygen Sensor Module
Gasboard7500E
Introduction Gasboard7500E Specification List

Gasboard 7500E ultrasonic oxygen sensor is an Method Ultrasonic
economical gas sensor used to detect oxygen O2: 0 ~ 100%;
concentration and gas flow in binary gases. Adopting Measurement range
Gas flow: 0 ~ 10L/min
ultrasonic detecting technology, Gasboard7500E has
better performance than electro-chemical and other Resolution O2: 0.1%; Gas flow: 0.1L/min
oxygen sensors. It has function includes data display, O2: ±1.8%FS@(10~45)℃
online monitor, and has been widely used in home and Accuracy
medical oxygen generator, large oxygen generator. Also, Gas flow: ±0.2L/min@(10~45)℃
we can offer ODM service as per customer’s demand. Repeatability O2: ±1% ; Gas flow: ±2%
Response time 0.5s
Main feature Working

10-50℃
temperature
 Cutting-edge ultrasonic technology adopted, oxygen
Storage temperature -20℃-60℃
concentration and flow measurement
Relative humidity 5-85%RH(non-condensing)
 Small size, stable, high accuracy, low cost
 No need of routine calibration Max pressure 150Kpa
 Long life span(>5years) Power supply 12.0±0.5VDC
 Customization available < 50mA，Pmax 0.6W, Average and

 Pass EMC test, able to reduce interference and get Working current peak current value is influenced by
engineers
the voltage
Dimensions 120x22x13.6mm (L*W*H)
Application
Weight 25g ( LED excluded)
 PSA oxygen generator/ concentrator
Analogue output 0-5V
 CPAP/ APAP ventilator
Communication UART-TTL
 Respiratory devices
no water vapor(no condensing); no
 Anesthetic machine Sample gas
dust(<1 μm)
 Vaporizer
www.gassensor.com.cn
Principle of measurement
Ultrasonic flow detection theory: When the ultrasonic wave transmits in the fluid, it will carry flow velocity under the
influence of fluid velocity. Fluid velocity can be measured by detecting the received ultrasonic signal to obtain the fluid
flow rate.
The feature of ultrasonic flow measurement is no obstructing fluid flow, etc.

Ultrasonic concentration detection theory: when the binary gas mixture composition has molecular weight difference, sound
travel speed varies from different gas composition.
Ultrasound Receiving
wave sending
I/O definitions
Fixing
hole Fixing hole
Fixing hole
Fixing hole Fixing hole
Inlet
Pin Pin definition Function description

Pin1：Vout1 0-5Vout put pin，0-99.9% oxygen concentration
J1 Pin2：Vout2 0-5Vout put pin，0-10L/min oxygen flow
Pin3：GND Public power supply output pins
Pin1：Vout +5V/10mA，power supply output
Pin2：Rx UART-Rx input pin (5V)
J2
Pin3：Tx UART-Tx output pin (5V)
Pin4：GND Public power supply output pins
Pin1：Vcc 12VDC，external power supply input pin
J5 Pin2：no No definition
Pin3：GND Public power supply input pins
Interface description
Linear output interface J1: Output voltage 0 ~ 5V, with the flow and O2 corresponding linear measurements. When the
voltage is 0 V DC, the corresponding output is 0, when the voltage is 5V, the corresponding output is full scale.
Serial port signal pin J2:TTL level (5V) can be connected with the external control panel TTL electrical level serial portal
and cannot be connected directly with the computer serial port. If it is connected with computer, then you need to
take special serial converter (TTL→RS232). With the serial port, the user can read real-time measurement results (gas
concentration and temperature) and do the maintenance.
Power supply interface J5: external power supply is 12 VDC.
Dimensions（unit: mm, tolerance±0.3mm）
Dimensions：120mmx22mmx13.6mm，around 25g（LED excluded).
Instructions
Please confirm before starting to test:

(1)Sample gas needs to be pretreated to make sure that the sensor entrance is clean, no water and no oil.
(2)Connect the sensor vent pipe with outside air to ensure the safety of emissions and ensure no blocking phenomenon.
(3)Make sure the sensor power supply is powered on.
 Do not smoke near the sensor and do not use naked flame.
 The integrity of the pipeline must be ensured to avoid gas leakage due to
pipeline rupture. Leakage of gas containing toxic and explosive gases may
cause serious accidents.
 The inlet pressure of the sensor must be within the required range of the
sensor to avoid pipeline loss or leakage caused by excessive pressure.
 When venting, please connect the vent pipe to the outdoor atmosphere and
do not disperse it in the sampling device or in the room. Do not allow
moisture to penetrate the sensor, otherwise it may cause electric shock or
internal short circuit.
 Under the condition without the permission of the manufacturer or
non-professional personal, do not disassemble the sensor, otherwise the
sensor manufacturers do not provide warranty or maintenance services for
the damage.
 Please read the instructions carefully before using the sensor to avoid
personal injury or damage of the sensor.
Package
Package dimension：395mm x 320mm x 470mm(L*W*H)

Weight：maximum 9.02Kg（full）
Note：Packing box is divided into three layers, and the layers are separated by pearl board.
Total number of sensor is 10*2*5*3=300
Mode selection guide

1）Gasboard 7500E: Ultrasonic oxygen sensor, serial response mode,without analog voltage output；
2）Gasboard 7500E: Ultrasonic oxygen sensor, serial response mode, with analog voltage output；
3）Gasboard 7500E: Ultrasonic oxygen sensor, serial blinding mode, without analog voltage output.
Note: The OEM version ultrasonic oxygen sensor needs to be confirmed with our product manager. Serial response mode
means the MCU controller need to send query command, then the sensor will response; serial blinding mode means the
sensor sends data in timing, then the MCU controller only needs to receive the measurement data.
After-sales services and consultancy

TEL：86- 27-81628827 FAX：86-27-87401159
ADD：Fenghuang No.3 Road,Fenghuang Industrial Park, Eastlake Hi-tech Development
Zone, Wuhan 430205, China
WEB: Http://www.gassensor.com.cn
E-mail: info@gassensor.com.cn

Ultrasonic Oxygen Sensor Module Gasboard7500E

Uploaded by

Copyright:

Available Formats

Ultrasonic Oxygen Sensor Module Gasboard7500E

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ultrasonic Oxygen Sensor Module Gasboard7500E

Uploaded by

Copyright:

Available Formats

Ultrasonic Oxygen Sensor Module

Introduction Gasboard7500E Specification List

Main feature Working

 Long life span(>5years) Power supply 12.0±0.5VDC

 Customization available < 50mA，Pmax 0.6W, Average and

The feature of ultrasonic flow measurement is no obstructing fluid flow, etc.

Fixing hole Fixing hole

Pin Pin definition Function description

Power supply interface J5: external power supply is 12 VDC.

Dimensions：120mmx22mmx13.6mm，around 25g（LED excluded).

Please confirm before starting to test:

Package dimension：395mm x 320mm x 470mm(LWH)

Mode selection guide

After-sales services and consultancy

You might also like