Citroen Evasion 01: Specific Vehicle Alarm Fitting Instructions Rev. 00

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV.
00
www.cobra.it
PETROL
MAKE CITROEN MOD. EVASION YEAR. 01 → DIESEL X
ALARM/SIREN Position the compact alarms and the sirens in the engine compartment, passenger’s side.
POSITION
CENTRAL UNIT POSITION The modular systems and the modules should be positioned under the dashboard, driver’s
side.
POWER SUPPLY +30: connect to the YELLOW wire, at the position nr. 1, in the 15 way black connector coming
out of the central doors locking unit located behind the glove compartment, passenger’s side.
-31: connect to the GREEN wire, at the position nr. 13 of the 15 way black connector coming
IGNITION WIRE +15/54: connect to the VIOLET wire, at the position nr. 5 of the 15 way black connector coming
DIRECTION INDICATORS Connect to the WHITE wire, at the position nr.10, and to the YELLOW wire, at the position
nr.2, of the 15 way black connector, coming out of the central doors locking unit located
behind the glove compartment, passenger’s side.
ELECTRIC WINDOWS Positive control signal

Front window, driver’s side:
cut the WHITE wire located in the wiring harness coming out of the motor of the driver’s side
door.
Front window, passenger’s side:
cut the PINK wire.
Rear window, driver’s side:
cut the BLUE wire.
Rear window, passenger’s side:
cut the GREEN wire.
These wires are in the wiring harness coming out of the driver’s side door.
Compass rear window, driver’s side:
cut the PINK wire located in the wiring harness coming out of the relative motor.
Compass rear window, passenger’s side:
cut the PINK wire located in the wiring harness coming out of the relative motor.
The above motors are located behind the plastic cover of the supports of the hatchback.
CENTRAL DOORS LOCKING Negative control signal

It is necessary to cut the wire at the position nr. 5 located in the wiring harness coming out of
the 26 way yellow connector of the central doors locking unit placed behind the glove
compartment, passenger’s side. It is suggested to refer to the diagram nr. 71 for antithefts of
the Bridge serie or to the diagram nr. 71A for antithefts of the 3100 serie.
IMMOBILISATION POINT Gasoil pump

Cut the LIGHT BLUE wire, at the position nr. 121, under the BROWN double relay, located in
the engine compartment, behind the driver’s side headlamp.
STARTER CUT OFF + 50: Cut the WHITE wire located in the wiring harness coming out of the black connector of
the ignition key.
BONNET SWITCH Install an additional switch on the front headlamp support grill, driver’s side.
DOORS SWITCH Connect to the GREY wire, at the position nr. 15, of the 15 way black connector coming out of
the central doors locking unit placed behind the glove compartment, passenger’s side.
BOOT SWITCH Connect to the wire marked 8616, at the position nr. 16, of the 26 way yellow connector,
coming out of the central doors locking unit placed behind the glove compartment, passenger’s
side.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed cieva01gbd.doc
as per the instructions given on the product installation manual.

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
www.cobra.it
FITTING DIAGRAM N° 71
To make the central doors locking on

CITROEN BERLINGO – EVASION – XSARA 2 mod. 2001
(for “Bridge” car alarms)
VIOLET/ORANGE ORANGE GREY/BLACK VIOLET
Towards the
driver’s side door
M
Connector coming out of the central doors
locking unit of the vehicle, located behind
the glove compartment, passenger’s side.
Note: The wire indicated in the alarm fitting instructions of Citroen Berlingo, Evasion and
Xsara 2 must be interrupted as per the above drawing. Pay attention that the position of the
wire that must be interrupted changes as per the vehicle.

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
www.cobra.it
FITTING DIAGRAM N°71A
To make the central doors locking on

CITROEN BERLINGO – EVASION – XSARA 2 mod. 2001
(for 3100 serie car alarms)
VIOLET/WHITE ORANGE GREY/BLACK VIOLET

ORANGE/WHITE
Towards the
driver’s side door
M
Connector coming out of the central doors
locking unit of the vehicle, located behind
the glove compartment, passenger’s side.
Note: The wire indicated in the alarm fitting instructions of Citroen Berlingo, Evasion and
Xsara 2 must be interrupted as per the above drawing. Pay attention that the position of the
wire that must be interrupted changes as per the vehicle.

Citroen Evasion 01: Specific Vehicle Alarm Fitting Instructions Rev. 00

Uploaded by

Copyright:

Available Formats

Citroen Evasion 01: Specific Vehicle Alarm Fitting Instructions Rev. 00

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Citroen Evasion 01: Specific Vehicle Alarm Fitting Instructions Rev. 00

Uploaded by

Copyright:

Available Formats

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV.

ELECTRIC WINDOWS Positive control signal

CENTRAL DOORS LOCKING Negative control signal

IMMOBILISATION POINT Gasoil pump

as per the instructions given on the product installation manual.

To make the central doors locking on

VIOLET/ORANGE ORANGE GREY/BLACK VIOLET

as per the instructions given on the product installation manual.

FITTING DIAGRAM N°71A

To make the central doors locking on

VIOLET/WHITE ORANGE GREY/BLACK VIOLET

as per the instructions given on the product installation manual.

You might also like