Experiment 3: Bipolar Junction Transistor Characterization: 1 Objective

UNIVERSITY OF CALIFORNIA AT BERKELEY
College of Engineering
Department of Electrical Engineering and Computer Sciences
EE105 Lab Experiments
Experiment 3: Bipolar Junction Transistor

Characterization
1 Objective
The BJT was invented in 1948 by William Shockley at Bell Labs, and became the first mass-produced
transistor. Having a good grasp of the physics of the BJT is key to understanding its operation and
applications. In this lab, we will explore the BJT’s four operation regions and determine its characteristic
values: DC current gain β and Early voltage VA . The transistor we will use is the 2N4401, an NPN device.
It is strongly suggested that you read and understand the section on BJT physics before beginning this
experiment.
2 Materials
Component Quantity
2N4401 NPN BJT 2
1 MΩ resistor 1
5 kΩ resistor 1
100 Ω resistor 1
Table 1: Components used in this lab
3 Procedure
3.1 Determining the Region of Operation
1. Set up the circuit shown in Figure 1, with RB = 1 MΩ, RC = 5 kΩ, and RE = 100 Ω. Set VCC to 5 V.
2. Increase VBB until IC = 0.5 mA. Measure VBE and VBC . What is the region of operation of the
transistor?
Warning: Never set VBE higher than 5 V for any of the transistors we use. Doing so will permanently
damage the transistor.
3. Now measure IB . What is the value of β?
4. From the value found above, calculate α. Use α to calculate IE , then measure IE and check if the
values agree.
5. Let’s examine the temperature dependence of collector current. Put two fingers around Q1 to heat it,
then measure IB and IC (have your partner heat the BJT while you measure the currents if you’re
having trouble doing both at the same time). How does IC compare to the value you measured before
you heated the transistor?
1
3 PROCEDURE 2
RC IC
IB
RB VCC +
−
VBB +
− RE IE
Figure 1: BJT measurement setup for this lab
6. Explain, using the equation you know for collector current, how you’d expect IC to vary with tempera-
ture. Does this agree with your experimental results? If not, explain why this might be the case. Hint:
IS depends on the intrinsic carrier concentration ni and the diffusion coefficients Dn and Dp . Intu-
itively, how would ni , Dn , and Dp change with temperature? How would IS change with temperature
as a result?
7. Look at the datasheet for the 2N4401. Does β (called hF E in the datasheet) agree with the values
given in the datasheet (Hint: A plot of hF E versus IC is given under “Typical Characteristics”)? If
the values do not agree, explain why you might see discrepancies.
8. Set VBB to 4 V and VCC to 2 V. Measure IB , IC , VBE , and VBC . What is the region of operation of
the BJT?
9. Set VBB to −3 V and VCC to 5 V. Measure IB , IC , VBE , and VBC . What is the region of operation
of the BJT?
10. Swap the emitter and the collector of the BJT in the circuit (you can do this by physically turning the
device to face the opposite direction). Set VBB to 4 V and keep VCC at 5 V. Measure IB , IC , VBE ,
and VBC . What is the region of operation of the BJT?
3.2 Determining the Early Voltage Using the HP4155

Increasing the collector-base bias widens the depletion region at the interface. As a result, recombination
decreases because the base is more depleted in mobile holes, which are the main recombination source for
injected electrons from the emitter. The widened depletion region also provides a greater electric field to
sweep the injected electrons to the collector. Both of these effects result in an additional dependence of IC
on VCE . The Early voltage is used to model this dependence.
1. Connect a BJT to the parameter analyzer’s test fixture (without any resistors). Use ICS to bias the
emitter at 0 V and the base at 0.6 V. Sweep the collector from 0 V to 5 V. Measure the current
through the collector terminal.
2. Run the measurement and plot IC versus VC , the collector voltage. What two regions of operation are
shown and where is the boundary?
3. Use this plot to determine the Early voltage, VA . Hint: The HP4155 Tutorial has instructions that
should help you calculate the Early voltage using Excel.
4. Repeat your calculation of VA for base voltages of 0.625 V, 0.65 V, 0.675 V, and 0.7 V (you can step
the base voltage in ICS to get this data). Does VA depend on the base voltage VB ? Why?
3 PROCEDURE 3
3.3 The BJT as a Diode

1. Connect a diode-connected BJT (i.e. the base and collector are shorted) to the parameter analyzer’s
test fixture. Use ICS to ground the emitter and sweep the base/collector from 0 V to 0.7 V. Measure
the current through the base/collector (acting as the P side of the diode).
2. Run the measurement and plot the base/collector current IC vs. VBE . What semiconductor device
does this I-V curve look like?
3.4 The Darlington Pair (Super High β)
VCC = 3 V
Q1
VBB +
− 1.2 V Q2
Figure 2: Darlington configuration for measurement
1. Construct the Darlington pair with your second BJT as shown in Figure 2.
2. Measure IB1 , IC1 , IB2 , and IC2 . Calculate β1 = IC1 /IB1 and β2 = IC2 /IB2 .
3. What is the overall current gain, βtot = IC2 /IB1 ? Use the formula you derived in the prelab to calculate
the total current gain from β1 and β2 and compare the calculation to your measurement.

Experiment 3: Bipolar Junction Transistor Characterization: 1 Objective

Uploaded by

Copyright:

Available Formats

Experiment 3: Bipolar Junction Transistor Characterization: 1 Objective

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Experiment 3: Bipolar Junction Transistor Characterization: 1 Objective

Uploaded by

Copyright:

Available Formats

UNIVERSITY OF CALIFORNIA AT BERKELEY

EE105 Lab Experiments

Experiment 3: Bipolar Junction Transistor

Table 1: Components used in this lab

Figure 1: BJT measurement setup for this lab

3.2 Determining the Early Voltage Using the HP4155

3.3 The BJT as a Diode

3.4 The Darlington Pair (Super High β)

Figure 2: Darlington configuration for measurement

You might also like