Viewsonic - vx2450w WM Led 1 vs13518 1w 2w PDF

Service Manual
ViewSonic VX2450W/WM-LED-1
Model No. VS13518-1W/2W
24" Wide LCD Monitor
(VX2450W_WM-LED-1 SM Rev. 1a Jul. 2010)

ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright
Copyright© 2010 by ViewSonic Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of ViewSonic Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further,
ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents
hereof without obligation of ViewSonic to notify any person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision SM Editing Date ECR Number Description of Changes Editor
1a G G 07/21/10 Initial Release Sophia Kao
ViewSonic Corporation 1 Confidential - Do Not Copy VX2450W/WM-LED-1

TABLE OF CONTENTS
1. Precautions and Safety Notices ...................................................................................... 3
2. Specification .................................................................................................................... 6
3. Front Panel Function Control Description ................................................................... 22
4. Electronic Circuit Theory................................................................................................. 39
5. Adjusting Procedure ........................................................................................................ 43
6. Troubleshooting Flow Chart ........................................................................................... 71
7. Block Diagrams .............................................................................................................. 77
8. Schematic Diagrams ...................................................................................................... 78
9. PCB Layout Diagrams .................................................................................................... 84
10. Exploded Diagram And Spare Parts List...................................................................... 88
11. Recommended Spare Parts List .................................................................................. 92

1. Precautions and Safety Notices
1. SAFETY PRECAUTIONS
This monitor is manufactured and tested on a ground principle that a user’s safety comes
first. However, improper used or installation may cause damage to the monitor as well as
to the user.
WARNINGS:
This monitor should be operated only at the correct power sources indicated on the
label on the rear of the monitor. If you’re unsure of the power supply in you residence,
consult your local dealer or Power Company.
Use only the special power adapter that comes with this monitor for power input.
Do not try to repair the monitor by yourself, as it contains no user-serviceable parts.
Only the qualified technician can repair it.
Do not remove the monitor cabinet. There are high-voltage parts inside that may
cause electric shock to human bodies.
Stop using the monitor if the cabinet is damaged. Have it checked by a service
technician.
Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power
cable immediately and consult your closed dealer.
Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth.
Apply non-ammonia based cleaner onto the cloth, not directly onto the glass screen.
Do not place heavy objects on the monitor or power cord.
2. PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety visual inspections
and the protection afforded by them cannot necessarily be obtained by using replacement
components rated for higher voltage, wattage, etc. Before replacing any of these
components read the parts list in this manual carefully. The use of substitute replacement
parts, which do not have the same safety characteristics as specified in the parts list, may
create shock, fire, or other hazards.
3. SERVICE NOTES
When replacing parts or circuit boards, clamp the lead wires around terminals before
soldering.
Keep wires away from high voltage, high temperature components and sharp edges.
Keep wires in their original position so as to reduce interference.
Adjustment of this product please refers to the user’ manual.

4 HANDLING AND PLACING METHODS

2. Specification
2.1 Introduction
1 LCD Pane CMO M236H3-LA2
PANEL Display Area 521.28mm(H)x293.22mm(V) 23.547” diagonal
(1st Optimum color active matrix TFT LCD
source) Resolution 1920x1080
Pixel Pitch 0.2715 mm (H) x 0.2715mm (V)
Glass Anti-Glare type, Hard-coating (3H)
Treatment 1000 :1 (Typ.) 700:1(min)
Contrast Ratio (CR>= 10,000,000:1
Dynamic 10) 170 Deg H and 160 Deg V (Typ.)
Contrast 16.7 M (6-bits + Hi FRC)
Viewing Angle 300 cd/m2 (Typ.) / 250 cd/m2 (min)
LR,UD Tr+Tf: 5ms (Typ.) / 8ms (Max.)
Colors One light bar with White-LED
Luminance 15000 Hrs (Min)
Response N/A (Typ.)
Time
Backlight
Backlight Life
Mercury
2 INPUT Video RGB Analog (0.7 / 1.0 Vp-p , 75 ohms),
SIGNAL DVI-D (TMDS, 100ohms)
Sync Separate Sync / Composite Sync / SOG

Fh = 24 – 83 kHz ; Fv = 50 – 75 Hz
3 COMPATIB PC PC Compatibles (from VGA up to 1920x1080
ILITY Mac Non Interlaced)
Power Mac (up to 1920x1080 )
4 Recommende 1920x1080 @ 60Hz
d
640 x 350 @ 70Hz
RESOLUTI Supported 640 x 400 @ 60, 70Hz
ON 640 x 480 @ 50, 60, 67, 72, 75Hz
720 x 400 @ 70Hz
720 x 480 @ p60, i60Hz
720 x 576 @ p50, i50Hz

800 x 600 @ 56, 60, 72, 75Hz
832 x 624 @ 75Hz
1024 x 768 @ 50, 60, 70, 72, 75,
75Hz
1152 x 864 @ 75Hz
1152 x 870 @ 75Hz
1152 x 900 @ 67Hz
1280 x 720 @ p50, p60Hz
1280 x 768 @ 50, 60, 75Hz
1280 x 960 @ 50, 60, 75Hz
1280 x 1024 @ 50, 60, 75Hz
1360 x 768 @ 60Hz
1440 x 900 @ 60, 75Hz
1400 x 1050 @ 60Hz
1600 x 1200 @ 60Hz
1680 x 1050 @ 60Hz
1920x1080 @ i50, p50, i60,
p60Hz
5 CONNECT Video Analog D-sub
ORS
Digital DVI ( Supported HDMI ver. 1.3 /Display port 1.1
spec)
Audio Audio In
3.5 mm jack (green ) for VX2450wm-LED
Power
Internal Power Adapter, 3-pin plug (CEE22)
6
AUDIO Speaker 2.5Wx2 for VX2450wm-LED only
7 POWER Voltage AC 100-240V (Universal); 50/60 Hz
8 ERGONO Tilt 20 ~ -5 degrees

MICS Swivel N/A
Rotation N/A
Height Adjust N/A

9 CONTROL Physical Key [ Power ]
S buttons [ 1 ], [Up], [Dn], [ 2 ]
on the
OSD Function front Auto Image Adjust
panel Contrast/Brightness
Input Select
Main D-SUB, DVI
Menu
Color Adjust
sRGB, 9300K, 7500K, 6500K, 5000K, User
Color [R, G, B]
Information
Manual Image Adjust
H/V Position, Horizontal Size, Fine Tune,
Sharpness,
Dynamic Contrast, Response Time, Aspect
Ratio , ECO Mode
Setup Menu
Language, Resolution Notice, OSD Position,
OSD Timeout,
OSD Background, Auto Power Off
Memory Recall
[ 1 ] : Main Menu
[ 2 ] : Input Select
[Up] or [Dn] : To immediately activate Contrast

and Brightness OSD Menu.
Short cut [Up] + [Dn] : Recall Contrast and Brightness to
key default in its menu without OSD
message.
[ 1 ] + [ 2 ] : Toggle 720x400 and 640x400 mode

[ 1 ] + [Up] + [Dn] : Auto White Balance
[ 1 ] + [Dn] : Power Button Lock
[ 1 ] + [Up] : OSD Lock
[ 2 ] + [Dn] : Toggle DDC/CI and DDC/2B

10 BANDWID Analog : 185 MHz
TH Digital : 165 MHz
11 OPERATIN Temperature 32°F to 104°F (0°C to 40°C)
G Humidity 20% to 90% (no condensation)
CONDITIO
N
12 STORAGE Temperature -4°F to 140°F (-20°C to 60°C)°
/ Humidity 5% to 90% (no condensation)
SHIPPING
CONDITIO
N
13 DIMENSIO Physical: Display 521.21 mm (W) x 403.71 mm (H) x
NS (W x H x D) w/ Stand 189.98mm (D)
20.52" (W) x 15.89" (H) x 7.48" (D)
Wall
Mount 521.21 mm (W) x 339.44 mm (H) x 49mm (D)
20.52" (W) x 13.36" (H) x 2.63" (D)
Packing (W x
H x D) 569 mm (W) x 495 mm (H)x126 mm (D)
22.4" (W) x19.5" (H) x4.9" (D)
14 WEIGHT Net 4.5 kg
Net (w/o 4.05 kg
stand)
Gross 6.2 kg
15 REGULATI UL, CUL, FCC-B (ICES), CB, CE, CES-003B,
ONS ISO13406-2, TUV/GS, ERGO, TUV-S, NOM,
GOST-R, HYGIENIC (20 copies), CCC, BSMI,
PSB, C-TICK, MIC(KCC), SASO, WEEE, RoHS,
SASO, Ukraine
16 RELIABILI MTBF 100,000 Hr (Excluding Panel).
TY
17 POWER "On" Blue Normal
SAVING "Active Off" AMBER ≦ 0.1 W
FUNCTION “Off” ≦ 0.1 W
18 LOGISTIC Container Standard 20’: 560 pieces 40’: 1176 pieces for VSA only
S Load 20’: 656 pieces 40’: 1344 pieces for WW.
(20' / 40')
56 sets

Pallet Load
VX2450w
UPC Code -led
VX2450w 76690747961 4
m-led 76690748002 3
Serial Format
VX2450w
-led S4Y
VX2450w S4Z
EDID Code m-led
Byte 10 – 0 x 25, Byte 11 – 0 x CB
Country of
origin Made in China
19 Wall Mount VESA 100mm x 100mm
20 OTHERS DDC/2B, DDC/CI, HDCP, Detachable Base,
KENSINGTON MicroSaver Security Compatible,
WorldWide Model, Windows XP, Vista Premium,
Windows 7,
21 Package LCD Display
Contents Power Cable
VGA Cable
DVI Cable
Audio Cable for VX2450wm-LED only
Quick Start Guide
ViewSonic Wizard CD-ROM
Notes:
The Input Signal and Resolution spec above might be different from segment 4.5.
The display shall fulfill all the criteria in segment 4.5.

2.2 product definition and specification
Product Name ViewSonic VX2450w/wm-LED
Oracle P/N VX2450W/WM-LED
Model Number VS 13518
English
French
German
Spanish
Italian
OSD Languages Finnish
Russian
Japanese
Korean
Traditional Chinese
Simplified Chinese
TFT LCD Panel and Model # 1st panel: CMO M236H3-LA2
Scalar Novatek NT68668UFG
Input Signal D-Sub /DVI
Sync Compatibility Separate Sync / Composite Sync / SOG
Adapter Internal Power Board
Power Cable (Refer to APPENDIX B) Yes
15 pin mini D-SUB Analog Cable (1.8 m,
black), with PC 2001.
Yes
(Detached cable; refer the Appendix A)

DVI-D Cable(1.8m, black) with PC 2001
Yes
(refer to Appendix A)
Audio Cable(1.8m, black) with PC 2001 Yes for VX2450wm-LED
MIC Cable(1.8m, black) with PC 2001 No
USB Cable (V2.0)
No
(1.8m, black) with PC 2001

English French
German Dutch
Finnish Swedish
Italian Spanish
Greek Russian
Czech Hungarian
Turkish Polish
ViewSonic CD Wizard
Romania Bulgaria
Slovakia Croatia
Serbia Slovenia
Portuguese Arabic
Japanese Traditional Chinese
Korean Simplified Chinese
Ukraine
English French
German Dutch
Finnish Swedish
Italian Spanish
Greek Russian
Czech Hungarian
Turkish Polish
ViewSonic Quick Start Guide
Romania Bulgaria
Slovakia Croatia
Serbia Slovenia
Portuguese Arabic
Japanese Traditional Chinese
Korean Simplified Chinese
Screen Protector Mylar Yes

Service Insert (Refer to Segment 5.9.3) For Region code = M units only
SRS Insert No
Energy Star Sticker Yes
POP Sticker (Refer to Segment 5.8.3) No
Warranty Card For Region code = G units only
Warranty Carton Sticker (refer to F8.1) For Region code = G units only
PE bag of Carton For Region code = G units only
MPR label For India drop shipment only

2.3 General Specification
Test Resolution & Frequency 1920x1080@ 60Hz

Test Image Size Full Size
Factory Default:
Contrast and Brightness Controls
Contrast = 70%, Brightness = 100%
2.4 Video Interface
Input Connector (refer the Appendix A) Analog = DB-15 (Analog)

Digital = DVI-D (Digital)
Default Input Connector Defaults to the first detected input
Equal to twice the weight of the monitor for
Video Cable Strain Relief
five minutes
Refer to Appendix A;
Video Cable Connector Pin out
Compliant DDC/2B and DDC/CI
Video RGB (Analog)
Video Signals Separate Sync / Composite Sync / SOG
TMDS (Digital)
Video Impedance 75 Ohms (Analog), 100 Ohms (Digital)
Maximum PC Video Signal 950 mV with no damage to monitor
Maximum Mac Video Signal 1250 mV with no damage to monitor
Sync Signals TTL
Compliant with version 1.3;
DDC/2B The DDC communication shall not interrupt
when power off.
Compliant with Revision 1.1;
DDC/CI The DDC communication shall not interrupt
when power off.
Digital link protection HDCP
Support HDMI 1.3 and Display Port 1.1 spec.
Sync Compatibility Separate Sync / Composite Sync / SOG
Shall be compatible with all PC type
Video Compatibility computers, Macintosh computers, and after
market video cards
Resolution Compatibility Refer to Segment 4-5
Exclusions Not compatible with interlaced video

2.5 USB Interface
No USB interface
2.6 Power Supply
Internal Power Supply TBD

Input Voltage Range 90 to 264 VAC
Input Frequency Range 47 to 63 Hertz
Short Circuit Protection Output can be shorted without safety issue
Over Current Protection 5.0A typical at 24VDC
( Protect when short circuit)
Leakage Current 3.5MA (MAX) AT 264VAC / 60HZ
Efficiency (at 115VAC Full Load) Typical: 80%
Minimum: 75%
Fuse Internal and not user replaceable
Power Output TBDWatts (typ)
Ripple and Noise Ripple:<3%
Noise: <1%
Max Input AC Current 1.5A (MAX)
Inrush Current (Cold Start) 80 A MAX./ 240VAC / 50HZ
(COLD START AT 25℃,FULL LOAD)
Power Supply Cold Start Shall start and function properly when under
full load, with all combinations of input voltage,
input frequency, and operating temperature.
Power Supply Transient Immunity Shall be able to withstand an ANSI/IEEE

C62.41-1980 6000V 200 ampere ring wave
transient test with no damage.
Power Supply Line Surge Immunity Shall be able to withstand ±1KV (L-L) and
±2KV (L-PE)
(Refer to EN55024:1998 / CISPR24.1997 /

IEC1000-4-5: 1995 / EN61000-4-5: 1995)
Power Supply Missing Cycle Immunity Shall be able to function properly, without
reset or visible screen artifacts, when ½ cycle
of AC power is randomly missing at nominal
input.

The power supply shall not produce audible
noise that would be detectable by the user.
Audible shall defined to be in compliance with
Power Supply Acoustics
ISO 7779 (DIN EN27779:1991) Noise
measurements of machines acoustics. Power
Switch noise shall not be considered.
Power Saving Operation(Method) VESA DPMS Signaling
Mode LED Power Consumption

On Blue TBDW (typ) TBDW (typ)
w/o Audio
TBDW TBD W (Max)
(max) w/o Audio
ECO Blue TBD W TBD W
Power Consumption
Mode (Optimize) (Optimize)
w/o Audio
TBD W TBD W
(Conserve) (Conserve)
w/o Audio
Active off Amber ≦ 0.1 W
Off ≦ 0.1 W
Recovery Time On Mode = N/A, Active Off < 3 sec
2.7 Electrical Requirement

Item Condition Spec Remark
Contact discharge : 4KV 150pF/330ohm.
Electrostatic Contact discharge : 8KV ● Each point 20
InnoLux SPEC
Discharge Air discharge : 8KV times.
Air discharge : 15KV ● 1 time/Sec
Note: ESD test does not include VGA, DVI pin.

Timing Table
Digital - TMDS
Analog
Composite
Separated
Item Timing Remark
SOG
640 x 350 @ 70 Hz, 31.5 KHz v v v v DMT.
For Separated、 SOG and
Composite sync, switch
1. 640x350@70,640x400@70,
and720x400@70 by [1]+[2]
short cut key ( primary =
720x400@70)
640 x 400 @ 60 Hz, 31.5 KHz v v v v DMT
For Separate, Composite
and SOG sync, switch
640x400@60Hz and
2.
640x480@60Hz and
720x480@60Hz by [1]+[2]
short cut key (primary =
640x480@60Hz)
640 x 400 @ 70 Hz, 31.5 KHz v v v v DMT
3. 640x350@70,640x400@70,
and720x400@70 by [1]+[2]
720x400@70)
4. 640 x 480 @ 50 Hz, 24.7 KHz v v v CVT
640 x 480 @ 60 Hz, 31.5 KHz v v v v DMT
640x400@60Hz and
5.
640x480@60Hz and
720x480@60Hz by [1]+[2]
640x480@60Hz)
6. 640 x 480 @ 67 Hz, 35 KHz v v v v For MAC
7. 640 x 480 @ 72 Hz, 37.9 KHz v v v v DMT

8. 640 x 480 @ 75 Hz, 37.5 KHz v v v v DMT
720 x 400 @ 70 Hz, 31.5 KHz v v v v DMT
9. 640x350@70,640x400@70,
and720x400@70 by [1]+[2]
720x400@70).
720 x 480 @ 60 Hz, 31.5 KHz v v v v 1. DTV, For Analog sync,
the information OSD shows
640x480.
2. For Separate, Composite
10.
640x400@60Hz and
640x480@60Hz and
720x480@60Hz by [1]+[2]
640x480@60Hz)
11. 720 x 576 @ 50 Hz, 31.3 KHz v v v v DTV
12. 800 x 600 @ 56 Hz, 35.2 KHz v v v v DMT
13. 800 x 600 @ 60 Hz, 37.9 KHz v v v v DMT
14. 800 x 600 @ 72 Hz, 48.1 KHz v v v v DMT
15. 800 x 600 @ 75 Hz, 46.9 KHz v v v v DMT
16. 832 x 624 @ 75 Hz, 49.7 KHz v v v v MAC
1024 x 768 @ 50 Hz, 39.6 KHz v v v v CVT
and SOG sync, Switch
1024x768@50Hz and
17. 1280x768@50Hz by [1]+[2]
1024x768@50Hz)
1024 x 768 @ 60 Hz, 48.4 KHz v v v v DMT;

18. and SOG sync,
Switch 1024x600@60Hz
and 1024x768@60Hz by

[1]+[2] short cut key
(primary =
1024x768@60Hz )
19. 1024 x 768 @ 70 Hz, 56.5 KHz v v v v DMT
20. 1024 x 768 @ 72 Hz, 58.1 KHz v v v v DMT
1024 x 768 @ 75 Hz, 60 KHz v v v v DMT;
For Separated , Composite
and SOG,
21.
(primary =
1280x768@75Hz)
22. 1024 x 768 @ 75 Hz, 60.2 KHz v v v v For MAC
23. 1152 x 864 @ 75 Hz, 67.5 KHz v v v v DMT
24. 1152 x 870 @ 75 Hz, 68.7 KHz v v v v For MAC
25. 1152 x 900 @ 67 Hz, 62.5 KHz v v v v For SUN
26. 1280 x 720 @ 50 Hz, 37.5 KHz v v v v DTV
27. 1280 x 720 @ 60 Hz, 45 KHz v v v v DTV
1280 x 768 @ 50 Hz, 39.6 KHz v v v v DMT
For Separated and
Composite sync, Switch
28. 1024x768@50Hz and
1280x768@50Hz by [1]+[2]
1024x768@50Hz)
1280 x 768 @ 60 Hz, 47.8 KHz v v v v DMT;
and SOG sync,
29.
and 1360x768@60Hz and
1366x768@60Hz by [1]+[2]
1280x768@60Hz )
1280 x 768 @ 75 Hz, 60.3 KHz v v v v DMT;
For Separated , Composite
30.
and SOG,

(primary =
1280x768@75Hz)
31. 1280 x 800 @ 60 Hz, 49.7 KHz v v v v DMT
32. 1280 x 800 @ 75 Hz, 62.8 KHz v v v v DMT
33. 1280 x 960 @ 50 Hz, 49.4 KHz v v v v DMT
34. 1280 x 960 @ 60 Hz, 60.0 KHz v v v v DMT
35. 1280 x 960 @ 75 Hz, 75.2 KHz v v v v DMT
1280 x @ 50 Hz, 52.7 KHz v v v v DMT
36.
1024
1280 x @ 60 Hz, 64 KHz v v v v DMT
37.
1024
1280 x @ 75 Hz, 80 KHz v v v v DMT
38.
1024
1360 x 768 @ 60 Hz, 47.7 KHz v v v v DMT;
and SOG sync,
39.
1366x768@60Hz by [1]+[2]
1280x768@60Hz )
1366 x 768 @ 59.79 Hz, 47.7 KHz v v v v DMT;
and SOG sync,
40.
1366x768@60Hz by [1]+[2]
1280x768@60Hz )
41. 1440 x 900 @ 60 Hz 55.9 KHz v v v v DMT
42. 1440 x 900 @ 75 Hz 70.6 KHz v v v v DMT
1400 x @ 60 Hz 65.3 KHz v v v v DMT;
1050 For Separated , Composite
43. and SOG,
and 1680x1050@60Hz by

(primary =
1680x1050@60Hz)
1400 x @ 75 Hz 82.3 KHz v v v v DMT
44.
1050
1600 x @ 60 Hz 75.0 KHz v v v v DMT
45.
1200
1680 x @ 60 Hz 64.7 KHz v v v v DMT
46.
1050
1680 x @ 60 Hz 65.3 KHz v v v v DMT;
1050 For Separated , Composite
and SOG,
47.
and 1680x1050@60Hz by
(primary =
1680x1050@60Hz)
48. 1920x1080 @ 60 Hz 67.5 KHz v v v v DMT
49. 480i @ 60 Hz
50. 480p @ 60 Hz
51. 576i @ 50 Hz
52. 576p @ 50 Hz
53. 720p @ 50 Hz
54. 720p @ 60 Hz
55. 1080i @ 50 Hz
56. 1080i @ 60 Hz
57. 1080p @ 50 Hz
58. 1080p @ 60 Hz
*1. Tolerance ≧ ±2KHz (if no overlapping issue)

*2. Any timing not in the list, it should display as normal or show on “OUT OF RANGE” OSD message
without blanking.
*3. The image quality of 50Hz mode might be worse than 60Hz.
.Primary Presets
1920x1080 @ 60Hz
User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration
Changing Modes

● Maximum Mode Change Blank Time for image stability : 5 seconds (Max), excluding “Auto
Adjust” time
● It should recall factory setting when execute Auto Image Adjust function by following
conditions,
1. Memory recall under DOS mode (640 x 350, 720 x 400 & 640 x 400).
2. New timing mode detected under DOS mode (640 x 350, 720 x 400 & 640 x 400).
● The monitor needs to do “Auto Adjust” the first time a new mode is detected
(see section “0-Touch™ Function Actions”)
● While running Change Mode, Auto Adjust or Memory Recall, the image shall blank

3. Front Panel Function Control Description
3.1 Front Panel Hardware Controls
Power Switch AC Power Switch on the back cover
Soft Power Switch on the front bezel
Power LED (Front Head) Blue – ON
Amber – Active Off
Dark = Soft Power Switch OFF
Front Panel Controls (Head) [ ] Power
[ 1 ] [ 2 ] [ ] [▲] [▼] [ 1 ] BUTTON 1
[ 2 ] Button 2
[▲] UP ARROW BUTTON
[▼] DOWN ARROW BUTTON
Note: Power Button, Button 1 and Button 2

must be one-shot logic operation. (i.e. there
should be no cycling)
Reaction Time OSD must fully appear within 0.5s after
pushing Button 1
3.2 Short Cuts Function from the button(s)

[1] Main Menu
[2] Input toggle (Analog or DVI; refer to Appendix D)
[▼] To immediately activate Contrast and Brightness OSD Menu.
[▲] To immediately activate Contrast and Brightness OSD Menu.
For
[▼]+ [▲] Recall Contrast and Brightness to default in its menu without OSD
VX2450w
message.(Under Contrast or Brightness adjust sub-menu, recall
Contrast or Brightness to its default without OSD message. )
[▼] To immediately activate Audio Adjust menu.
[▲] To immediately activate Contrast / Brightness OSD Menu.
1. In the Audio mode, recall both of Volume and Mute to default
without OSD message.( Under Volume adjust sub-menu, recall
For Volume to default without OSD message.)
VX2450wm 2. In the BT / CR mode, recall both Contrast and Brightness to
[▼]+ [▲]
default in its menu without OSD message. (Under Contrast or
Brightness adjust sub-menu, recall Contrast or Brightness to its
default without OSD message.)
* While OSD menu off, recall CR/ BT/ Audio volume and mute to default without OSD

message
[1] + [2] 1. Toggle 640x350@70Hz, 720x400@70Hz and 640x400@70Hz

mode when input 640x350@70Hz or 720x400@70Hz or
640x400@70Hz mode
2. Toggle 640x400@60Hz, 720x480@60Hz and 640x480@60Hz
mode when input 640x400@60Hz or 720x480@60Hz or
640x480@60Hz mode
3. Toggle 1024x768@75Hz and 1280x768@75Hz mode when input
1024x768@75Hz or 1280x768@75Hz mode
4. Toggle 1280x768@60Hz 1360x768@60Hz and1366x768@60Hz
mode when input 1280x768@60Hz 、1360x768@60Hz or
1366x768@60Hz mode
5. Toggle 1400x1050@60Hz and 1680x1050@60Hz mode when
input 1400x1050@60Hz or 1680x1050@60Hz mode
[1] + [▼] + [▲] White Balance
(Keep pushing 5 sec) 1. It will not shown on user’s guide
2. OSD message as below,
(Image = no blanking)
3. Recommend environment
3.1. Optical (Best) input timing = 640 x 480 @ 60Hz;
Following timing modes also
recommended,
800 x 600 @ 60 Hz
1024 X 768 @ 60 Hz
3.2. Pattern as below,
[1] + [▲] OSD Lock

(refer to segment 4-6-4)
[1] + [▼] Power Lock

[2] + [▼] Toggle DDC/CI and DDC/2B (DDC/CI enable/disable)
and show following message for 3 seconds,
When switch to DDC/CI
When switch to DDC/2B
Default = DDC/CI
Signal + [2] + [ ] Factory Mode
Remark : All the short cuts function are only available while OSD off

3.3 Factory Defaults
Item Defaults Item Defaults
Contrast 70% Input Priority N/A
Brightness 100% Resolution Notice On
Color Temperature 6500K Volume 50%
(for VX2450wm)
Sharpness 50% Balance N/A
OSD H. Position 50% Treble N/A
OSD V. Position 50% Bass N/A
OSD Time Out 15 720x400@70Hz / 720x400@70Hz
640x400@70Hz /
640x350@70Hz
DCR OFF 720x480@60Hz / 640x480@60Hz
640x480@60Hz /
640x400@60Hz
OSD Background On 1280x768@60Hz / 1366x768@60Hz
1360x768@60Hz /
1366x768@60Hz
ECO mode Standard 1024x768@75Hz / 1280X768@75Hz
1280x768@75Hz
Aspect ratio Full screen
3.4 AUDIO Interface (SPEAKER SPECIFICATION, For VX2450WM-LED only)
Line input connection 3.5 mm stereo jack

Line input signal 1.0 Vrms
Line input impedance 10k Ohm
Maximum power output 2.5±10% W /ch
Signal to Noise Ratio 50 dB
Frequency response FO – 20 Khz
Distortion < 10 % THD (@1kHz)
There should be no audible vibration with volume at

Vibration
100% and treble / bass at default
There should be no affect on the screen image stability
Screen image
under any conditions
Connector PC99 requirement Audio in Lime Green pantone # 577C
Cable type / length 3.5mm stereo cable / 1.8m length

Speakers stay off when the rest of the monitor is in
Audio DPMS
power saving
3.5 TFT LCD Panel

Panel Characteristics :
1st Source Panel
Supplier CMO
Model name M236H3-LA2

Display Area 521.28(H) X 293.22(V)
Pixel Pitch 0.2715(H) X 0.2715(V)
Display Colors 16.7M (6 bit with HI- FRC)
Number of Pixel 1920(H) X 1080(V),
Brightness 250cd/m2 (Min.), 300m2 (Typical)
Min: 700:1
Contrast Ratio
Typical: 1000:1
Hor: 170°,
Viewing Angle
Ver: 160° (Typical, CR>10)
Display Mode Normally White
Frame rate 60Hz
Response Time 5 ms(Typical), 8ms (Max.)
Surface Treatment Anti-glare, Haze=25%,Hard Coating (3H)
Lamp one LED
Outline Dimension 544.8(W) X 320.5(H) X 11.4(D) (typ.)
Brightness
1.33(Max)
uniformity
*The average of measured value from monthly shipment shall be equal or better than the Typical value
above.

Packing For Shipping And Disassembly Procedure Packing
For Shipping
1. Packing Procedure
1.1 Paste protection film to protect the monitor. (Figure 1)
1.2 Put the monitor in the PE bag and seal the bag with tape.(Figure 2)
1.3 Put the cushions on the monitor

1.4 Place the monitor into the carton and then put all the accessories into the carton.
At last, close the carton and seal it with tape.(Figure3)
AUDIO CABLE
DVI CABLE
POWER
MONITOR HEAD
Figure 3

Disassembly Procedure

4. Electronic Circuit Theory
4.1 Switching Mode Power Supply
4.1.1 AC Current Input Circuit
P801 is a connector for connecting AC Power. F801 is a fuse to protect all the circuit. AC
input voltage is from90V to 264V. R801and R802 joined between two inputting main circuit
to prevent man from shock. L801 is used to clear up low frequency wave. C801 and C802
are used to discharge the waves that L801 produced. High frequency waves are damped
by C801 and C802. D801 is a rectifier which composed of 4 build-in diodes, it invertsAC to
DC.
4.1.2 High Voltage to Low Voltage Control Circuit

C804 is used to smooth the wave from rectifier. IC802 is a highly integrated PWM
controller, which build-in a power MOSFET. When rectified DC high voltage is applied to
the DRAIN pin during start-up, the MOSFET is off initially, and the CONTROL pin
capacitor is charged through a switched high voltage current source connected internally
between the DRAIN and CONTROL pins. When the CONTROL pin voltage Vc reaches
approximately 5.8V, the control circuitry is activated and the soft-start begins. The
soft-start circuit gradually increases the duty
cycle of the MOSFET from zero to the maximum value over approximately 10ms. If no
external feedback/supply current is fed into the CONTROL pin by the end of the soft-start,
the high voltage current source is turned off and the CONTROL pin will start discharging in
response to the supply current drawn by the control circuitry.Resistors R814 are for
external current limit adjustment, and used to reduce the current limit externally to a value
close to the operating peak current of primary about 1.35A. The mean
is power will protected when the primary current over about 1.35A.When PWM is turned
off, the main current flow will be consumed through D802 and ZD802, This will prevent
MOSFET which built-in IC802 from being damaged under large current impulse and
voltage spike. IC801 provide internal Auxiliary current to CONTROL pin during normal
operation. In addition, error amplifier and feedback current to the CONTROL pin are for
duty cycle control.
4.1.3 DC_5V and DC_19V Output Circuit

For DC 5V, D807,D808 and D809 is used to rectify the inducted current. C817 C818
C830and L802 C820 are used to store energy when current is reversed. The parts
including C817 C818 C830and L802 C820 are used to smooth the current waves. For DC
19V, D804 and D805 is used to rectify the inducted current. C816 and C825 are used to
store energy when current is reversed. The parts including C816, C825 are used to
smooth the current waves.

4.1.4 Feedback and OVP Protect Circuit
Pin R of IC803 is supplied 2.5V stable voltage. It is connected to 5V and 19V output
through R830,R831 and R823. and R824 are output sampling resistor. When the sampling
voltage morethan 2.5V or less than 2.5V, feedback current of IC802 will change, this can
change the voltage fromtransformer T801.Q804, R822, and ZD801 make up of dummy
loading circuit. For start-up sequence, during 5Voutput take place high loading first, this
dummy loading circuit operated to insure 19V not be increased.
4. 2 LED Circuit
4.2.1 Low voltage to high voltage circuit
19VDC provides the power for IC501; the control signals Brightness and ON/OFF come
from I/F board.ON/OFF signal connect to pin10 of IC501 and makes IC501 enable.
Brightness signal connect to pin1 of IC501and regulates the panel brightness, The
operation frequency is determined by the external Resistor R522 and capacitorR505
connected to pin13 of IC501. BURST MODE regulated dimming
frequency is determined by the external resistor R505 connected to pin13 of IC501. C508
is used for soft start and compensation, C506, R508 are used for dump noise.
The output drives, (pins16 respectively) output square pulses to drive MOSFET U501,
U501 is N channel MOSFET. U501 work as Boost topology, it is high efficient, PWM
switching.
During start up, OVP (pin11) senses the voltage at the output voltage. When OVP
reaches 1V, the output voltage is regulated.
The current flowing through LED is sensed and regulated through sense resistor
R515,R516,R517,R518,R519,R520. The feedback voltage connected to Pin2~Pin5 and
Pin7~Pin10 (ISEN).
4.3 I/F Board Circuit

4.3.1 Power Input
+5V is from the power board and supply for the panel and for the LDO. +3.3V is form the
LDO output used for U105 (Scaler IC: NT68668UFG), and then 3.3V output is generated
from +5V through C101, C104 and C102 filtering, and U101 outputs. +3.3V is only used for
U105.
4.3.2 MCU & Scaler(TSUM1PLR-LF)

The frequency of XTAL1 is 12.000MHz. U105 # 65 is defined as panel_enable. When the
I/O port is high, Q101 and Q104 are conducted. And then after C108 and C109 filtering,
obtain the voltage of VLCD, which will be connected to CN105. U105 # 29 is defined as
VGA_ DET connected with CN102 #5. U105 # 1 is a pin of hardwire reset. U105 # 79-#

80,#81-#82, #83-#84, #85-#86,#87-#88 output LVDS digital data of 8 bit to panel control
circuit through CN105. U105 # 117 generates a PWM waveform by regulating the duty to
control the brightness of the backlights.U103 is EEPROM used for saving EDID data,
which is connected by SCL and SDA pins with #35 and #34 of NT68668FG. U108 is a
flash memory, U106 # 6, # 5 are the communications with U105 #49-#50.U106 is
EEPROM used for saving user’s OSD setting.
4.3.3 VGA Input

Signal R, G, B input through CN102 #1, #2, #3, and C116, C117 and C118 filtering the
high frequency noise. Signal HSYNC and VSYNC input through CN102 #13 and #14, and
C129, R135, C130, R136 filtering. Then the analog signal enters U105, and then U108
deals with it internally. In addition, EP112, EP107, EP104, EP105, EP106, EP108, EP109,
EP110, EP111,are ESD protector. Signal DDC-SCL inputs via CN102 #15, and then
passes through EP108 for ESD protection, goes into EDID EEPROM IC U103. Signal
DDC-SDA inputs via CN102 #12, and then passes through EP111 for ESD protection,
goes into EDID EEPROM IC U103. CN102 #5 is defined as cable detect pin, this detector
realizes via R121 and U105 #29,The PC-5V of U103 is supplied by PC via CN102 #9 with
EP107 for ESD protection, or supplied by Monitor self via D106. U103 is an EEPROM IC,
which is a kind of memory and used for saving EDID data.
4.3.4 Button Control

Button “Key-Power” is defined as power on/off, which is connected to U105 #122 through
CN104 #6. Button “Key-2” is defined as two functions of selecting and adjustment, which is
connected to U105 #125 through CN104 #2.
Button “Key-Up” is defined as plus, which is connected to U105 # 67 through CN104 #10.
Button “Key-Down” is defined as minus, which is through connected to U105 #126 through
CN104 # 5.
Button “Key-1” is defined as two functions of menu and exit, which is connected to U105 #
66 through CN104 # 1.
LED indicator on the front bezel is defined as follows:
a. When press button “Key-Power”, U105 # 124 is pulled high and U105 # 123 is pulled
Low, so Q108 is conductedand the LED indicator is Blue.
b. When in power-saving mode, U105 # 123 is pulled high and U105 #124 is pulled down,
so Q106 is conducted andthe LED indicator is orange.
4.4 Power On/Off Sequence

4.4.1 Hardware Power ON
When power cord is plugged into AC socket, SMPS starts work and provides U105 with

VCC3.3V. When VCC5V inputs, U105 resets circuit active, sets U105 all registers to
preset modes, and then monitor goes into stand-bymode. That means hardware power
on has been completed.
4.4.2 Software Power ON/OFF

When press power key, U105 # 122 recieves low pulse,and then U105 will do the power
on/off.
- If Power ON, U105 # 123(LED Green) will send out Low potential, and then LED Blue on.
- If Power OFF, U105 # 123(LED Blue) will send out High potential, and then LED Off.
The Panel_Vcc, Backlight_En, CLK/DATA output to panel will follow the following
sequency.

5. Adjustment Procedure
5.1 Key Function Description
CONTROL
KEYS FUNCTION
KEY
[AUTO] [2] By pressing [AUTO] key, “Auto Image Adjust” is performed
[MENU] [1] By pressing [MENU] key, Main menu display

A. When “MENU OSD” display, press these keys to change the
contents of an adjustment item, or change an adjustment value
[▼] [▲] B. When “MENU OSD” is un-display, press these keys to change
brightness and contrast
[POWER] [ ] Power on or power off the monitor
5.2 Hot Key Operation
[1] Main Menu

[2] Auto Image Adjust
[▼] To immediately activate Audio menu.
To immediately activate Contrast menu. It should be
[▲]
change to Brightness OSD by push button [2]
1. In the Audio mode, recall both of Volume and Mute to
default without OSD message.
[▼]+ [▲]
2. In the BT / CR mode, recall Contrast or Brightness to
default in its menu without OSD message.
1. Toggle 720x400@70Hz 、640x350@70Hz and
640x400@70Hz mode when input 720x400@70Hz 、
640x350@70Hz or 640x400@70Hz mode
2. Toggle 640x400@60HZ ,
720x480@60Hz,640x480@60 mode when input
640x400@60HZ , 720x480@60Hz,640x480@60
mode
[1] + [2] 3. Toggle 1024x768@50Hz and 1280x768@50Hz mode
when input 1024x768@50Hz or 1280x768@50Hz
mode
4. Toggle 1024x768@75/60Hzand 1280x768@75/60Hz
mode when input 1024x768@75/60Hz or
1280x768@75/60Hz mode
5. Toggle 1600x900@60Hz(Reduced) and
1280x960@60Hz mode when input 1600x900@60Hz

(Reduced)or 1280x960@60Hz mode
6. Toggle 1600x900@60Hz and 1440x900@60Hz mode
when input 1600x900@60Hz or 1440x900@60Hz
mode
White Balance
1. It will not shown on user’s guide
2. OSD message as below,
[1] + [▼] + [▲]
(Keep pushing 5 sec)
(Image = no blanking)
[1] + [▲] OSD Lock
[1] + [▼] Power Lock
No signal + [2] + power Burning mode
[2] + power Factory Mode
Remark : All the short cuts function are only available while OSD off
5.3 OSD Control

5.3.1 OSD Table
Main Menu
1. Key button definition:
[1]: OSD off
[2]: Execute the selected function
[Up]: Rolling up the slider
(When push the button on the top position, the slider
shall go down to the bottom item)
[Dn]: Rolling down the slider
(When push the button on the bottom position, the

Level 1 Level 2 Level 3
Auto Image Adjust
1. Background = blanking
2. The message OSD position is at the
center.
3. After auto tune, OSD shall be off
4. Only for analog mode
Contrast/Brightness Contrast
1. Adjust range = 0 to 100
2. Default = 70
[1] = Back to Main Menu or OSD off
(depend on previous status)
[Up] = Increase the OSD value setting
[Dn] = Decrease the OSD value setting
[Up]+[Dn]: Recall to default

Brightness
Key button definition:
[1]: Back to previous OSD status
[2]: select to adjust value setting.
[Up]: Move up the slider
[Dn]: Move down the slider
2. Default = 100
[1] = Back to Main Menu or OSD off
(depend on previous status)
[Up]: Increase the OSD value setting
[Dn]: Decrease the OSD value

Input Select D-SUB
Step 1: Turn off OSD.
Step 2:
1. Target video input port = Analog
2. If signal detected from target port,
change to target port.
3. If no signal detected from target port,
keep existing input port.
Step 3: Show on Input Message OSD at
the right-top corner of screen for 1
1. Show on existing input port by second.
white-background color
[2]: Change to the selected input port
[Up]: Move up the slider
[Dn]: Move down the slider
DVI
Step 1: Turn off OSD.
Step 2:
1. Target video input port = Digital
2. If signal detected from target port,
change to target port.
3. If no signal detected from target port,
keep existing input port.
Step 3: Show on Input Message OSD at
the right-top corner of screen for 1
second.
Color Adjust sRGB

Change Color setting to sRGB
9300K
Change Color setting to 9300K

7500K
6500K
5000K
User Color Red
1. Show on existing input port by Change Color setting to user color

2. Default = 6500K
[2]: Change to the selected color
setting 1. Adjust range = 0 to 100

[Up]: Move up the slider 2. Default = 100
[Dn]: Move down the slider 3. Key button definition:
[1]: Back to Color Adjust OSD

4. Under DCR mode (Dynamic [2]: selected setting.
Contrast = On), SRGB shall be [Up]: Increase the OSD value
disabled with fate-out color. And it setting
should not be selected. [Dn]: decrease the OSD value
setting

Green
2. Default = 100
[2]: selected setting.
[Up]: Increase the OSD value
setting
[Dn]: decrease the OSD value
setting

Blue
2. Default = 100
[2]: selected setting.
setting
[Dn]: decrease the OSD value
setting
Information
Key button definition:
[1]: Back to Main Menu OSD

Manual Image Adjust H/V Position Horizontal Position
[1]: Back to Manual Image
Adjust OSD
[2]: Change to Vertical Position
OSD
setting
Vertical Position
1. Key button definition: 1. Adjust range = 0 to 100

[1]: Back to previous OSD status 2. Key button definition:
[2]: Execute the selected function [1]: Back to Manual Image
[Up]: scroll up the slider Adjust OSD
(When push the button on the top [2]: Change to Horizontal
position, the slider shall go down Position OSD
to the bottom item [Up]: Increase the OSD value
[Dn]: Scroll down the slider setting
(When push the button on the [Dn]: Decrease the OSD value

bottom position, the slider shall Horizontal Size
go down to the top item
2. Under Digital mode, all the H./V.
Position, Horizontal Size and Fine
Tune shall be disabled with
fate-out color. And it should not be
selected.
3. Under native mode, Sharpness
shall be disabled with fate-out
color. And it should not be
selected.
4. Under SRGB mode, Dynamic
Contrast shall be disabled with 1. Adjust range = 0 to 100
fate-out color. And it should not be 2. Key button definition:
selected. [1]: Back to Manual Image Adjust OSD
Fine Tune
[1]: Back to Manual Image Adjust OSD

Sharpness
1. Adjust range = {0 / 25 / 50 / 75 / 100}
2. Default = 50
[1]: Back to Manual Image Adjust OSD
Dynamic Contrast
Swap on and off the Dynamic Contrast
function
Default = Off
= On
= Off
When Dynamic Contrast is on, below
functions will be disabled:
1. Brightness/Contrast menu
2. SRGB selection in Color Adjust
3. White balance hot key
4. DDC/CI BR/CT adjustment
Aspect Ratio 4:3
Change aspect ratio to 4:3

Full Screen
Fill screen with panel native aspect
ratio.
1. Show on existing Aspect Ratio setting
by white-background color
[2]: Change to the selected Display
Mode setting.
[Up]: Scroll up the slider
(When push the button on the top
position, the slider shall go down to
the bottom item)
[Dn]: Scroll down the slider (When push
the button on the bottom position,
the slider shall go up to the top item)
3. Default = full screen
Note : 1.When input signals are wide
format, this function is disable.
2.When input signals are non-wide
format. this function is enable.

ECO Mode Standard
OSD adjust range = 0 to 100
1. This function toggles ECO mode.
2. Show on existing ECO Mode setting by
[2]: Change to the selected Display
Mode setting. Optimize
[Up]: Scroll up the slider OSD adjust range = 0 to 100
the bottom item)
[Dn]: Scroll down the slider
(When push the button on the
bottom position, the slider shall go up
to the top item)
4. Default = Standard
5. Under sRGB mode, ECO Mode shall
be disabled with fate-out color. And it
should not be selected.
6. No matter DCR on or off, lamp current

will be changed by ECO mode change.
7. While ECO or DCR setting changed,

the lamp current shall be updated to
new setting immediately.
8. Do not lock Contrast or Brightness
OSD for ECO function

9. Following is the lamp current chart, Conserve
OSD adjust range = 0 to 100
Setup Menu Language Select English

Set OSD language to English and
keep in Language Select OSD
French
Set OSD language to French and
German
Set OSD language to German and

Spanish
Set OSD language to Spanish and
Italian
1. Key button definition: Set OSD language to Italian and
[1]: Back to Main Menu OSD keep in Language Select OSD
[2]: Execute the selected function Finnish
[Up]: Scroll up the slider Set OSD language to Finnish and
(When push the button on the keep in Language Select OSD
top position, the slider shall go Russian
down to the bottom item) Set OSD language to Russian and
[Dn]: Scroll down the slider 1. Show on existing by white-background keep in Language Select OSD
(When push the button on the color

Japanese
bottom position, the slider shall 2. Key button definition:
Set OSD language to Japanese
go down to the top item) [1]: Back to previous OSD status
and keep in Language Select OSD
[2]: Change to the selected language
Korean
setting
Set OSD language to Korean and
[Up]: Scroll up the slider
Traditional Chinese
Set OSD language to Simplified
the bottom item
Chinese and keep in Language
[Dn]: Scroll down the slider
Select OSD
(When push the button on the bottom
Simplified Chinese
Set OSD language to Traditional
the top item
Chinese and keep in Language
Select OSD

Resolution Notice
Swap on and off the Resolution Notice
function
OSD Position OSD H. Position
2. Default = 50
[1]: Back to Setup Menu OSD
[2]: selected setting
setting (move OSD right)
setting (move OSD left)
value

OSD V. Position
2. Default = 50
[2]: selected setting
setting (move OSD up)
setting (move OSD down)
value
OSD Time Out 5

Set OSD Time Out to 5 Seconds
15
30
60
1. Adjust range = 5, 15, 30, 60
2. Default = 15
[Dn]: Decrease the OSD value setting
[Up]+[Dn]: Recall to default value

OSD Background
Swap on and off the OSD Background
= Non-transparent
= Transparent
Auto Power Off
Swap on and off the Auto Power Off

function
Power off the display automatically when
no signal is detected for 3 minutes.
= On
= Off
Note :
1. When no signal input with Auto
Power Off = ON, the display will go
into power saving first. After 3
minutes, the display will turn off
automatically.
2. When no signal input with Auto
Power Off = OFF, the display will go
into power saving as normal display.
3. Default = Off
4. Memory Recall will call back the
setting to default.
5. When push Power Lock hot key
under Auto Power Off = On, the
message OSD will show on for 3
seconds (Power Lock function is
disabled),
6. The function will be disabled

when power button locked.
Memory Recall

1. Background = blanking
2. Recall white balance to factory
setting
3. Recall all the OSD setting to the
default. (include the R/G/B in User
Color)
4. Show the message OSD position is
at the center for 3 seconds.
5. Clean FIFO timing mode buffer
6. Execute Auto Image Adjust
Note: Memory Recall should not effect
on Language, Power Lock Settings
or Input Priority
5.3.2 OSD Lock short cuts function for the buttons

The OSD lock will be activated by pressing the front panel control buttons [1] + [▲] for
10 seconds *1. If the user then tries to access the OSD by pressing any of the buttons, a
message will appear on the screen for 3 seconds showing "OSD Locked" *2. The OSD
lock will be deactivated by pressing the front panel control buttons [1] + [▲] again for 10
seconds*3.
*1 The OSD Lock message as below,
Range = 0 to 10
*2 The OSD Locked message as below,
*3 The OSD Unlock message as below,
Range = 0 to 10

*4 When the OSD is locked will lock all functions, including “Volume”, “Mute” and
others.
*5 Status bar indicating OSD Lock or Unlock is in progress and when complete it will
indicate “OSD Locked” or “OSD Unlocked” for 3 seconds as below,
OSD Locked
OSD Unlocked
*6 When OSD appears on screen, the OSD Lock/Unlock short cut key will be disabled.
5.3.3 Power Lock short cuts function for the buttons

The Power lock will be activated by pressing the front panel control buttons [1] + [▼] for
10 seconds *1. Locking the power button means that the user won't be able to turn off
the LCD while the power button is locked. If the user presses the power button while it
is locked, a message will appear on the screen for 3 seconds showing "Power Button
Locked" *2. It also means that with the power button locked, the LCD would
automatically turn back "On" when power is restored after a power failure. If the power
button is not in the locked mode, then power should return to it's previous state when
power is restored after a power failure. The Power lock will be deactivated by
pressing the front panel control buttons [1] + [▼] again for 10 seconds*3.
*1 The Locking Power Button message as below,
Range = 0 to 10
*2 The Power Button Locked message as below,

*3 The Unlocking Power Button message as below,
Range = 0 to 10
*5 Status bar indicating Power Button Lock or Unlock is in progress and when complete
it will indicate “Power Button Locked” or “Button Unlocked” for 3 seconds as below,
Power Button Locked
Button Unlocked
*6 When OSD appears on screen, the OSD Lock/Unlock short cut key will be disabled.
5.3.4 Resolution notice Action

1. Resolution Notice OSD should show on screen after changing to non-native mode
for 30 sec.

[1]: Turn off the OSD message.
[2]: Turn off the OSD message and disable Resolution Notice function
3. The OSD should disappear after 10 sec or by pushing button [1] or [2]

4. After the OSD turns off, it will not show on again before next timing change, input
change or power off.
5. Resolution Notice function should be disabled when push button [2] under
Resolution Notice OSD
6. The “1440x900” will be replaced by actual panel resolution.
5.3.5 0-Touch™ Function Actions

1. Execute Auto Image Adjust when new mode detected, and save the settings to
buffer for further use
2. It should be reset by Memory Recall function
(Should not reset by power off, power unplug and others)
5.3.6 OSD Auto Save

The OSD shall save new settings when it is turned off by the user or when it times out.
There shall not be a separate save
5.3.7 Out of range

While non-defined timing is detected, following OSD message will keeps showing on,
1. If the timing is over spec (Fh, Fv or dot clock), the image shall be blanking, and OSD
background shall be non-transparent.
2. If the timing is inspect but not defined, the image shall be non-blanking.
5.3.8 No signal
While no signal is detected for D-Sub and DVI, the following OSD message shall shows
on 3 seconds then go in to power saving.
OSD Background = Non-transparent

Image = Blanking
5.4 EDID (Rewrite EDID data to EEPROM)
If we need to rewrite the EEPROM data, please confirm the following steps.
1. Plug in VGA Cable; we can rewrite the EDID data to EEPROM by using “EDID Rewrite”
program.

2. If the “EDID Rewrite” process finished, please pull out VGA cable and press ‘’2’’+’’▲’’ at
the same time.
3. Pull out AC power cable or press power key to restart.
5.5 Upload firmware to MCU via VGA Cable
Connect ISP board between monitor and PC as below configure
Using novatek ISP Tool Update FW:

(1). System Frame
(2) Function Description

A. ISP ON

Set In-System Programming Enable
B. ISP OFF
Set In-System Programming Enable
C. Load File
Load Hex File to Buffer
D. Erase
Erase MCU Fash Rom
E. Program
Write Buffer Data to MCU Flash Rom
F. Auto
ISP ON→Erase→Promgram→ISP OFF
G. View Hex
View Hex File in Buffer
H. CheckSum
Read Data from MCU
(3). Initial Setting

a. After Setup EasyWriter, We must set EasyWriter settings according our
environment.
b. In “Option”, Select “Setup ISP tool”

C.How to Setting
Connect to Novatek ISP Board by USB, Select “NVT EasyUSB”.
USB IIC Speed Limit, Suggestion : Select “Low Speed”.
After Setting, Select “Comfirm Change” to confirm your change.
D.How to Program File to MCU Flash Rom

Step 1. Load Hex File to Buffer
Select “Load File” Button

Select File Type “Bank Switch(128k, 256k)
Select *.H00(* = FW Project Name(define in KeilC)
Select Confirm, Load File OK
Step 2. Set In-System Programming Enable

Select “ISP ON”, Enable ISP

Step 3. Erase MCU Fash Rom
Select “Erase”, Erase Flash,Avoid Conflict
Step 4. Write Buffer Data to MCU Flash Rom

Select “Program”, Program Buffer Data to Flash

Step 5. Set In-System Programming Disable
Disable ISP, Start MCU
Auto Mode
Step2 ~ Step5 = “Auto”
After Step 1,we can select “Auto” directly,to run Program File to MCU Flash Rom

6. Troubleshooting Flow Chart
6.1 No Power & Power LED Off
No power
Check primary Check circuit if

Check IC802,
rectifier voltage short
C804, T801,
Check F801, P801,
RT,801,D801
Check pin7 of IC802

CheckC810,D803,C807,
voltage about 16V
Check pin2 of IC802 voltage Check primary OVP, OLP
about 3V and secondary
Check pin5 of IC802 Check R804, R805
voltage is below 1.4V
END

6.2 DC output voltage is unstable
Unstable power
Check
Check sampling
R822,R825,R826,
Circuit
R822,R825,R826,
Check the R pin Check the C pin

Change
voltage of IC803 voltage of IC803
Check R832
Check pin7 of Check D803,C807,C810 if

IC802 voltage short
Change
Check pin3 of Change
IC802 voltage R833,R835,R805,R834
END

6.3 Output power is unstable
No raster?
Yes
LED Green?
Yes
Backlight can’t be
turned on.
Yes
No
I Check power
Invert supply
No Yes
Is there high-level voltage on Check I/F board
Is Ok R
pin6 of IC501? SCALER
Yes
No R505 open
No
Are connected rightly Connecting the
CN501, CN502, CN503 output connector
again
Yes
Yes
Is there instantaneously pulse No
U501, U502 fail
wave on pin1, pin16 of IC501 Is Ok IC501?
at the moment of restart?
No IC501 fail
Yes
No
T501, T502 fail
Is ok T501, T502?
Yes
Check feedback circuit

ISEN1,ISEN2,VSEN,OLP1,OLP2 END

6.4 Backlight can’t be turned on
Black Screen
NG
Check VCC
Power Fail
5V
OK
NG Check
Check VCC3.3V and
VCC1.8V FB103
OK
Check
FB102
NG
Check Reset
Check C151
Waveform
OK
NG
Check Crystal
Check
pin(96,97)waveform
Waveform
OK
OK OK
Check CCFL Check
Invert fail
Enable pin10 of
NG NG
Check R147,R111,R112,
U104 fail
and Q106

6.5 White Screen
White Screen
OK
LVDS cable Workmanship
reinsert
NG
OK
Change LVDS LVDS cable NG
cable
NG
OK
Check VLCD OK Check VLCD Panel Fail
Is 5V
singals
NG
Check panel Enable
of Panel Enable
OK
Check CN104
Check
Q101,Q103 and
END

6.6 Bad Screen
Bad Screen
OK
Workmanship
LVDS Cable
Reinsert
NG
Change LVDS
Cable
NG
NG
Check Crystal :pin Check X1,C150 and
127 and pin128 C152
OK
checkU105and
SDO/SCZ/SCK/SDI
SDO/SCZ/SCKSDI /RSTN

7. Block Diagram
VGA Input
VGA Input
Circuit
DDC
Flash Panel
24c02
SCALER
5V Switch
(NT68668)
to Panel
DVI Input
DVI Input
Circuit Back lamp
ON/OFF
DDC 5V to 3..3V
EEPROM
24c02 24C16
Key Input Key&LED

ON/OFF
EMI Filter Rectifier& Rectifier 5V Switch

AC Input
Circuit Filter Circuit Power filter 5V to inverter
Switch Output Protection
transformer feedback
MOSFET Switch B
PWM Control Rectifier
Circuit filter 14V
Output LED Driver
MCU
Volume Control Sampling
5V Input Voltage
Sampling
Voltage
Photocoupler
feedback
Audio Amplifier
Audio Input (PAM8603) Speaker

8. Schematic Diagrams
R815 C814
100R 1n 500V
C805 1 2
4700p/250V T801 D804
+19V
SPW-XXX SB540
3 D805 ZD801 R821
11 SB540 510R 2W
+ + C816 C813 27V
C806 12 C825 220u/35V
3
R807 4700p/400V 220u/35V R819
33K 0.1/50V 200R Q801
2
+ 1
R818 C815 2N4401
+ ZD803 2 22R 2.2n 500V
P6KE150A R822
1
1 2 10K
3 2
D801 C804 7
BL4-06 82u/450V
8
- D807
VCC 5V
SB540 L802
4
1
CN805 D802 D808 5uH F802
MUR1100ERL SB540 R839 5A/125V A_VCC5V
6
12 C824
HV D803
3 2
+ 1N4003 9 C830 C818 C817 C820
L801 C807 680u 10V 680u 10V 680u 10V 680uF 10V 0.1/50V 0.22R 2W C819
NC 11
20mH 47u/25V 10 680uF 10V
1 4 5
NC 10
C821
2200P Y1/NC
CS 9
R824
2
C808 110K 1%
2
1
8 NC R825 R823
NC
1
270R C823 R828 7.5k 1%
IC801 10nF/50V 4.7K
R801 7 4 1
3M D 2 1 2 1
C803 R836
6 3 2 200R 1%
NC
1
LTV817M R829
2
0.22u X2 5 NC C828
FB 0.1/100V
NC 4
RT801 C
5R 3 R814
GND 0R62 2W R
A IC803
1
250V 2 TL431 R830 R831
1
NC
2
10K 1%
10K 1%
2
CON10PIN
F801 1
VCC
3.15A/250V
C801
2200P/250V Y1 C802
2200P Y1
L N
1 2 3
P801
AC_SKT CN801
CN802
1 I2S_WS_LRCK
2 I2S_DATA
3 I2S_Bit_CLK 1 BRIGHTNESS
4 I2S_System_MCLK 2 ON/OFF
5 AUDIO_SW 3
6 VOLUME 4
7 MUTE 5
8 6 +19V
9 7
10 ON/OFF 8
11 BRIGHTNESS
8P 2.0mm
12
13 VCC 5V
14
14P 2.0mm

Note 2
VGA5V
Note 1 1 D103
3
CN101 +5V 3 VGA 5V BAV70 Note 5
C124 1000p/50V
C166 1000p/50V
2
1
2 U102
To Power/Inverter
3 +3.3V AS1117L-1.8TR-LF +1.8V

4
5 3 VIN VOUT 2
LED_ON/OFF +1.8V 5
6
ADJ
7 Brightness 5 PAD 4
8 Volume 5
GND
Board
+
9 Mute 5
C106 C103 C107
1
10 PSC 5
22u/16V 0.1/16V
1000P/50V
1000P/50V
1000P/50V
1000P/50V
1000P/50V
1000P/50V
10P 2.0mm DVI5V
1 D104
VCC5V 5
3
4 DVI5VC125 2 BAV70
1000p/50V Note 4
C160
C161
C162
C163
C164
GND
+5V Note 3 U101
GND D101 SSM24APT AS1117L-3.3TR-LF +3.3V
DIO--SMA 3 VIN VOUT 2
GND +3.3V 3,4,5
ADJ
R101 0 R0805 4
PAD
C104 +
C101 + C102
1
100u/16V 0.1/16V 100u/16V
+3.3V
R111 Q101
GND VCC5V AP2305GN VLCD
R140 2 3 VLCD 5
47K
4K7
LED_ON/OFF R112
0.1/16V
C108 51
100u/16V
3
0.1/16V R0402
1
1 Q103 R109
5 LED_ENABLE
3
PMBT3904 100K
R106 +
100K GND 1
2
C109
C110
R107
3
Q102
2
100K
1 2N7002
5 PANEL_ENABLE Q104
GND C112 R108 PMBT3904
1u/16V 47K
2
GND GND
Note:
1. Pin2 of CN101 need to NC for PCBA use.
2. PC5V can be used for scaler on power saving mode.
3. D101 must be co-layed with R101. D101 is used for ESD back drive.
4. U101 must contain TO263, TO252 and SOT223 package.
5. Using embedded 3.3 to 1.8 LDO NC U102 ,C106 ,C107 and C103

CN102 Note 2
DZ11AA1-H5W6-4F
11 1 R RB101 0 R114 75 C113 0.047u/16V
RED+ 5
6 R0603
12 2 G RB102 0 R115 75 C114 0.047u/16V
GREEN+ 5
7 R0603
13 3 B RB103 0 R116 75 C115 0.047u/16V
BLUE+ 5
R0603
75 1%
8
75 1%
75 1%
14 4 VGA5V R159 470 1% C134 0.047u/16V
SOG 5
9 Note 1 C116 C117 C118
15 5 10p/50V 10p/50V 10p/50V
10
R117
R118
R119
R122 75 C119 0.047u/16V
0
RED- 5
16
17
0
R123 75 C120 0.047u/16V
GREEN- 5
R124 75 C121 0.047u/16V
R120
R121
BLUE- 5
VGA_DET VGA_DET
VGA_DET 5
Note 3
GND
5P35V
5P35V
5P35V
5P35V
5P35V
+5V VGA5V
C126 0.1/16V
C127
EP107
EP104
EP105
EP106
0.1/16V VGA 5V 2
EP112
1
D106
BAV70
C128
0.1/16V
3
GND GND
R127 R128 R129

100K 100K 10K U103
R130
1K 8 VCC A0 1
7 WP A1 2
VGA_SCL R131 100 6 3
VGA_SDA R132 100 SCL A2
5 SDA GND 4
AT24C02BN
FB101 GND
120Ω
WP_EDID 4,5
R133 100
HSYNC 5
R134 100
VSYNC 5 DDC_SCL_VGA 5
DDC_SDA_VGA 5
33p/50V
33p/50V
5P35V
5P35V
5P35V
5P35V
2K2
2K2
Note 3
C131 C132
33p/50V 33p/50V
C129
C130
R135
R136
EP108
EP109
EP110
EP111
GND
GND
Note:
1. R120 is reserved for Samsung model.
2. R0603 package for Bead. C116,C117,C118 are reserved for EMI or performance issue.
3. C131,C132 are reserved for tuning performance issue.

+5V
CN201 DVI5V
DVI-D_CON
C105 C145
DVI_RX2- R201 10 1000p/50V 1000p/50V DVI5V 2
RX2- 1 RX2- 5
2 DVI_RX2+ R202 10
RX2+ RX2+ 5
GND 3
1
9 DVI_RX1- R203 10
RX1- DVI_RX1+ RX1- 5 D201
10 R204 10 GND BAV70 C201
RX1+ RX1+ 5
19 0.1/16V
GND DVI_RX0- R205 10
RX0- 17 RX0- 5
18 DVI_RX0+ R206 10
3
RX0+ RX0+ 5
22 R211 R212 R213
GND DVI_RXC+ R207 10
23 RXC+ 5 100K 100K 10K
RXC+ DVI_RXC- R208 10 U201
RXC- 24 RXC- 5 R214
1K 8 VCC A0 1
7 WP A1 2
6 DVI_SCL R209 100 6 3
SCL DVI_SDA R210 100 SCL A2
SDA 7 5 SDA GND 4
VS 8
AT24C02BN
WP_EDID 3,5
DDC_SCL_DVI 5
5V 14 DDC_SDA_DVI 5
15 DVI_DET DVI_DET
GND DVI_DET 5
16 HPD_DVI HPD_DVI GND
HP
RX4- 4
5 DVI5V
RX4+ DVI5V
GND 11
12 D202 D204 D206 D208
RX3- DVI5V 2
3
3
13 BAV99 BAV99 BAV99 BAV99
RX3+
RX5- 20 2 1 2 1 2 1 2 1
Note 1
5P35V
5P35V
5P35V
5P35V
RX5+ 21
DVI5V R217 10K
0.1/16V
0.1/16V
R218
5P35V
C203 C205 C207 C209 100/NC

+5V HPD_DVI
0.1/16V
0.1/16V 0.1/16V 0.1/16V 0.1/16V ZD101

R219
3
D203 D205 D207 D209 Q201
100p/50V
47K
3
3
6V2 PMBT3904
C212
C213
C214 0.1/16V
EP203
EP204
EP202
EP205
BAV99 BAV99 BAV99 BAV99 1 HPD_CTRL 5
C202
EP201
2 1 2 1 2 1 2 1
2
HDCP Function
C215
C204 C206 C208 C210
0.1/16V 0.1/16V 0.1/16V 0.1/16V GND
GND
Note:
1. R218 is reserved for some model.

+1.8V CVDD Note 1
AVCC_3V3 ADC_BIAS VAA_3V3 FB108 120Ω Note5

+3.3V +3.3V
+3.3V DVDD_3V3 Note 1 Note 1 Note 1
2,3,4 +3.3V FB104 FB107 FB106
FB102 Note 1 CN103
C148 100p/50V
30P 1.0mm
C123 100p/50V
C135 C137 C153
C155 0.1/16V
100p/50V
120Ω 30Ω 120Ω
C144 0.1/16V
C154 0.1/16V
0.1/16V 0.1/16V 0.1/16V
0.1/16V
0.1/16V
100p/50V
30Ω
C139 RXO0-
C142 0.1/16V
C152 0.1/16V
C156 0.1/16V
1u/16V C138 RXO0+ 30
C143
C159
+
C141 + C150 + 22u/16V RXO1- 29
22u/16V 220u/10V RXO1+ 28
C122
RXO2- 27
C111
VAA_1V8 RXO2+ 26
25
FB109 120Ω 24
RXOC-
GND RXOC+ 23
GND GND GND RXO3- 22
C147 C146 RXO3+ 21
4.7u/10V 0.1/16V RXE0- 20
RXE0+ 19
18
RXE1- 17
RXE1+ 16
15
Note: RXE2- 14
13
1. Each bypass capacitor (0.1u/16V) must be closed to pin that si DC power input of scaler IC. RXE2+
12
RXEC-
2. LED green driving circuit is reserved for some model. RXEC+ 11
3. Bypass capacitor C167,C168,C169,C170,C171,C172,C173 are for ESD and EMI issue. ESD component RXE3- 10
Note 4 RXE3+ 9
EP101,EP102,EP103 are for GPIO direct driving LED. 8
4. RL111,RL112,RL113,RL114 are reserved for some panel spec. RL111 0 LPIN6 7
6
5. CN103 is no locked packgae for normal model CN105 for 15.6w&18.5w B type single LVDS input RL112 0 LPIN5
5
panel. RL113 0
4
6. Pin2&Pin4 of CN104 need to NC for PCBA use. 3
ADC_BIAS
VLCD 2
+3.3V 1
VAA_1V8 GND
C133 AVCC_3V3 CON--FOX-HS9030E

FB110 120Ω 4.7u/10V CVDD VAA_3V3 DVDD_3V3
AVCC_3V3 2 VLCD
FOR Tw215N2
AVCC_3V3
C136
0.1/16V
Note5
115
119
116
45
43
52
26
15
17
28
51
90
53
6
2
CN105
AVCC_3V3
PLL_DVDD
PLL_GND
CVDD
CVDD
CVDD_ZP
ADC_VAA18
AVCC
AVCC
ADC_BIAS
ADC_VAA33
DVDD
DVDD
DVDD
DVDD_ZP
NC
R146 16 REXT DGND/CGND 100
DVDD_3V3 470 1% 99 30
DGND/CGND
C165 4 RX2+ 4 RX2+ DGND/CGND 98 29
0.1/16V 4 RX2- 5 RX2- DGND/CGND 97 28
4 RX1+ 7 RX1+ DGND/CGND 96 RXO0- 27
R189 R190 4 RX1- 8 RX1- DGND/CGND 95 RXO0+ 26
10K 10K GND U108 4 RX0+ 10 RX0+ DGND/CGND 94 25
8 2 SDO SDO 4 RX0- 11 RX0- DGND/CGND 93 RXO1- 24
VCC SO SCS 13 92 23
7 HOLD# CS# 1 SCS 4 RXC+ RXC+ DGND/CGND RXO1+
WP_FW 3 6 SCK SCK 4 RXC- 14 RXC- DGND/CGND 91 22
WP# SCK 21
4 GND SI 5 SDI SDI
RXO0-
RXO2-
R192 R191 T0M 88 RXO2+ 20
47K 1K PM25LV010A-100SCE 41 87 RXO0+ 19
3 HSYNC HSYNCI1 T0P RXO1-
3 VSYNC 42 VSYNCI1 T1M 86 RXOC- 18
85 RXO1+ 17
T1P RXO2- RXOC+
GND 3 BLUE+ 19 84 16
BIN1+ T2M RXO2+
GND 3 BLUE- 20 BIN1- T2P 83 RXO3- 15
82 RXOC- 14
TCLK1M RXOC+ RXO3+
3 SOG 21 SOG1I TCLK1P 81 13
22 80 RXO3- 12
3 GREEN+ GIN1+ T3M RXO3+
3 GREEN- 23 GIN1- T3P 79 11
77 RXE0- 10
T4M RXE0+
3 RED+ 24 RIN1+ T4P 76 9
25 75 RXE1- 8
+3.3V 3 RED- RIN1- T5M RXE1+
+5V 74 7
T5P RXE2-
3,4 WP_EDID 38 PA5/PWM7* T6M 73 6
34 72 RXE2+ 5
3 DDC_SDA_VGA PB7/DDC_SDA1* T6P
35 71 RXEC- 4
3 DDC_SCL_VGA
4 DDC_SDA_DVI 46
PB6/DDC_SCL1*
PB5/DVI_SDA0*
U105 TCLK2M
TCLK2P 70 RXEC+ 3
R177/NC 47 69 RXE3- 2
4 DDC_SCL_DVI PB4/DVI_SCL0* T7M RXE3+
2K2 68 1
R103 SCS 104 SPI_CE NT68668 T7P VLCD
2
SDO 105 62
LED_B_C 27K SPI_SO VCKI
Q107 1 SDI 106 61
PMBT3906 SCK SPI_SI V7 GND 30P 1.0mm
107 60
R166 WP_FW SPI_CLK V6 CON--FOX-HS9030E
5V_DET 108 PD4 V5 59
10K 58
3
R165 V4
V3 57 +3.3V
330 +3.3V 56
R144 V2
R0603 55
10K/NC
47K V1
47K
47K
5V_DET 30 54
TX 31 PB3/ADC3/INTE1 V0
TP1 P31/TXD
LED_B R167 RX R147 100 VSO R171 R138 R137
TP2 32 P30/RXD INT_VSO 113
R0603 100/NC R148 100 HSO 10K/NC 4K7 4K7 C140
33 PB2/ADC2/INTE0 INT_HSO 114
0.1/16V
R186
R185
R184
36 103 VSO
PA3/PWM5 PC7 HSO U106
37 PA4/PWM6* PC6 102
R125 1K 29 8 VCC A0 1
3 VGA_DET PD6 E2P_WP R145 1K 7 2
39 PA6/PWM8* WP A1
4 HPD_CTRL R216 1K +3.3V IICSCL R142 100 6 3
4 DVI_DET 40 PA7/PWM9* SCL A2
IICSDA R143 100
100K/NC
100K/NC
+3.3V 5 4
10K/NC
10K/NC
10K/NC
10K/NC
SDA GND
100K
100K
100K
10K
100K
100K
100K
Note2 AT24C16AN
E2P_WP R139 100 GND
48 PD5
DVDD_3V3 IICSDA 49 P35
R195
R182
R181
R180
R178
R172
R196
R179
R173
R174
R176/NC IICSCL
R194
R193
R183
50 P34
4K7
R175
2
126 R157 1K POWER

47K PB0/ADC0
Q108 1 Power 125 R158 1K ENTER TOUCH SCL
PMBT3906 PB1/ADC1 LED_A_C
R169 10K PC5 124
1 123 LED_B_C
RSTB PC4/PWM1 TOUCH POWER
122
3
C151 PC3/PWM0
R168 1u/16V R199
121 100 Mute 2
10 PC1* R153
R170 120 100/NC PSC 2
R0603 PC0* R154
UP
0改為1K 118 100 Volume 2
Power C157 R197 100 127 PWMB*
OSCI PWMA* 117 Brightness 2
22p/50V 110
R0603 PC2 LED_ENABLE 2
R160
2
X101 67 R188 1K TOUCH SDA

PA1/PWM3 R187 1K RESET
PA2/PWM4 66
DGND/CGND
DGND/CGND
DGND/CGND
DGND/CGND
DGND/CGND
+3.3V 1M 65
ADC_GNDA
PA0/PWM2 PANEL_ENABLE 2
12MHz
10K
1
DGND
DGND
DGND
PGND
AGND
AGND
C158 R198 100 128

GND
GND
22p/50V OSCO
R102
R161
除LED_Enable和Brightness外未變，
109
101
112
111
其他為Lowpower設計，被NC掉的全為與KEYPAD有關
44
64
78
18
12
27
89
63
2K2/NC
3
9
2
Q106 1 LED_A_C GND

PMBT3906
R162
10K
3
R163
500 Note6
R0603 CN104
LED_A R164/NC TOUCH SCL 2 1 RESET

R0603 100
4 3
TOUCH POWER 6 5 POWER
1000P/50V/NC
GND 8 7 LED_B
1000P/50V/NC
1000P/50V/NC
1000P/50V
TOUCH SDA 10 9 LED_A
2x5P 2.0mm
5P35V
1000P/50V
1000P/50V
5P35V
To Keypad Board
Note3
C171
C173
C167
C172
C168
C169
EP101
EP102
GND

IC501
INL858
5 BRIGHTNESS 1 PWM STATUS 24
R501 ISEN1 2 23 R508 C506

10K C501 ISEN1 NC 100 0.47/50V
1000p/50V ISEN2 3 22
ISEN2 SSTCMP
ISEN3 4 21
ISEN3 COMP
ISEN4 5 20
CN502 +19V ISEN2 ISEN1 ISEN4 SEL
CON 8PIN R526 6 19 C503 0.47/50V
0 GNDA VIN
1 R527 ISEN6 7 18
1 ISEN4 0 ISEN3 ISEN6 GNDP
2 2
3 ISEN7 8 17
3 ISEN7 VREF R507 R509
4 4
5 R528 ISEN8 9 16 NC 0
5 ISEN6 0 ISEN5 ISEN8 LDR
6 6
7 ISEN5 10 15
7 R537 ISEN5 ISW
8 8
ISEN8 0 ISEN7 OVP 11 14
R504 OVP ENA
30K 1% 12 13
ISET RT
R505 2.2U/50V 2.2U/50V
R525 30K 100K 1%
C505 C509 CN501
CONN LED
5 ON/OFF
ISEN6
R517 10 10
R502 R520 10
ISEN5 9
10K R503 ISEN4 8
470K C502 R516 10 7
1000p/50V 6
5
R524 4
C507 10 ISEN3 R519 10 3
100P ISEN2 R518 10 2
ISEN1 1
R515 10
R506 R523
100 1% 100
C5081000P R53210
D501
2
L501 U501AP9971GH SB200 R513
C504 33uH 300K
2.2u/50V 1
D502 OVP
3 SB200 C511 C512
1u/100V 1u/100V C513
10u/100V
R512 R511 R510
0.51 0.51 0.51 R514 CN502
11K C510 CONN LED
220p/50V
ISEN8 R538 10 12
ISEN7 R533 10 11
ISEN6 R539 10 10
ISEN5 9
R534 10 8
7
6
5
ISEN4 R540 10 4
ISEN3 R535 10 3
ISEN2 R541 10 2
ISEN1 1
R536 10

9. PCB Layout Diagrams

10. Exploded Diagram And Spare Parts List

EXPLODED PARTS LIST (VX2450W-LED)
ViewSonic Model Number: VS13518-1W
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Q'ty
1 NA 50118P23B200R TRANSPARENT DECORATION VX2450 1
2 NA 75003P21A801R SUB-ASSY,POWER BUTTON,LP21A8 1
3 NA 75003P21A800R SUB-ASSY,POWER BUTTON RING,LP21A8 1
4 NA 501110601000R LOGO THREE BRIDS 7.9MM LE2082 1
5 NA 50102P23B200R BACK COVER W/SPK W/DVI VX2450 1
6 E-00010229 631102240500H LCP 23.6"M236H3-LA2-902(A)(CMO) HF 1
7 B-00010488 795620500600R PCBA,LED CON/B,LP23B2-622 ROHS 1
8 NA 795361400600R PCBA,PI/B,W/SPK,LP21A8-622 ROHS 1
9 NA 79P231300500R PCBA,IF/B,LA2,W/SPK,LP23B2-522 ROHS 1
10 NA 70106P23B200R ASSY CHASSIS W/SPK W/DVI VX2450 1
11 NA 502020100700R LOCK SHEET,LP2259 1
13 NA 502090105600R VESA,LE23W2 1
14 NA 503020006300R RUBBER FOOT L14.8*W9.6*T3.5mm ,LE19E3 4
15 NA 50124P23B200R BASE VX2450 1
16 NA 06120303000R BAG EPE+PE W330xL300xT0.3mm CYCLE PRINTE 1
17 NA 71411P23B200R ASSY HINGE VX2450 1
18 NA 50126P23B200R STAND VX2450 1
19 NA 50202P21A801R BRACKET,STAND,INL,LP21A8 1
EXPLODED PARTS LIST (VX2450WM-LED)

Rev: 1a
1 NA 50118P23B200R TRANSPARENT DECORATION VX2450 1
2 NA 75003P21A801R SUB-ASSY,POWER BUTTON,LP21A8 1
3 NA 75003P21A800R SUB-ASSY,POWER BUTTON RING,LP21A8 1
4 NA 501110601000R LOGO THREE BRIDS 7.9MM LE2082 1
6 E-00010229 631102240500H LCP 23.6"M236H3-LA2-902(A)(CMO) HF 1
7 B-00010488 795620500600R PCBA,LED CON/B,LP23B2-622 ROHS 1
8 B-00010261 795361400600R PCBA,PI/B,W/SPK,LP21A8-622 ROHS 1
9 B-00010489 79P231300500R PCBA,IF/B,LA2,W/SPK,LP23B2-522 ROHS 1
10 NA 70106P23B200R ASSY CHASSIS W/SPK W/DVI VX2450 1
11 E-00010090 618100200790R Speaker 2.5W 4Ω 50&70mm R/B/G W/CASE 1
12 NA 502020100700R LOCK SHEET,LP2259 1
14 NA 502090105600R VESA,LE23W2 1
15 NA 503020006300R RUBBER FOOT L14.8*W9.6*T3.5mm ,LE19E3 4
16 NA 50124P23B200R BASE VX2450 1
18 NA 71411P23B200R ASSY HINGE VX2450 1
19 NA 50126P23B200R STAND VX2450 1
20 NA 50202P21A801R BRACKET,STAND,INL,LP21A8 1

PACKING PART LIST (VX2450W-LED)
Rev: 1a
1 P-00010438 50610LP23B02R CUSHION,EPS-R , LP23B2 1
2 CB-00008190 453030300370R CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS 1
3 CB-00008437 453010100380R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH 1
4 P-00009399 506120010900R BAG,PLASTIC，EPE+PE,L500xW670xT0.55mm,LP 1
5 DC-00010471 703010003100R KIT ASSY WW VX2450W-LP23B2 1
6 A-00008111 453070800150R PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx 1
7 P-00010439 50610LP23B00R CUSHION,EPS-M , LP23B2 1
8 P-00010437 50610LP23B01R CUSHION,EPS-L , LP23B2 1
9 PL-00008888 71402P23B200R ASSY BASE VX2450 1
11 NA 506431008200R FILM,PROTECTION,UNPRINTED,555x327x0.1mm, 1
12 P-00010436 50602P23B200R CARTON,VX2450W-LP23B2 1
13 NA 506440002300R LABEL,BLANK,76.2x76.2mm,LE1709(UPC) 1

PACKING PART LIST (VX2450WM-LED)
Rev: 1a
1 P-00010438 50610LP23B02R CUSHION,EPS-R , LP23B2 1
2 CB-00008190 453030300370R CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS 1
3 CB-00008437 453010100380R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH 1
4 NA 506120010900R BAG,PLASTIC，EPE+PE,L500xW670xT0.55mm,LP 1
5 DC-00010472 703010003200R KIT ASSY WW VX2450WM-LP23B2 1
6 A-00008111 453070800150R PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx 1
7 CB-00008002 453030300120R CABLE AUDIO 1P 6FT BLACK/GREEN CP03B06P0 1
8 P-00010439 50610LP23B00R CUSHION,EPS-M , LP23B2 1
9 P-00010437 50610LP23B01R CUSHION,EPS-L , LP23B2 1
10 PL-00008888 71402P23B200R ASSY BASE VX2450 1
12 NA 506431008200R FILM,PROTECTION,UNPRINTED,555x327x0.1mm, 1
13 P-00010440 50602P23B201R CARTON,VX2450WM-LP23B2 1
14 NA 506440002300R LABEL,BLANK,76.2x76.2mm,LE1709(UPC) 1

11. Recommended Spare Parts List
RECOMMENDED SPARE PARTS LIST (VX2450W-LED)
Rev:1a
Serial No. Prefix: S4Y
Ite Category Part Name Description ECR/EC ViewSonic Ref. P/N Ref. NO Compatibility
1 Accessories: Power Cord PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx(USA) A-00008111 453070800150R 6 Main Source
2 [Adapter, Remote Power Cord PWRCORD 7A/125V BLK 6FT CNS VCTF 3Gx0.75(TWN) A-00006733 453070800480R Main Source
3 Controller, Power Power Cord PWR CORD 16A/250V BLK 6FT VDE,H05VV-F 3G(Europe) A-00008279 453070801190R Main Source
4 Cord, External Power Cord PWRCORD 10A/250V BLACK 6FT SAA,H05W-F/3G(Australia) A-00003671 453070800420R Main Source
5 Power Cord PWRCORD 16A/250V BLK 6FT KTL,H05VV-F 3Gx(Korea) A-00006734 453070800500R Main Source
Cables]
6 Power Cord PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx0.(China) A-00005255 453070800170R Main Source
7 Power Cord PWRCORD 5A/250V BLK 6FT UK3Gx.75mm(SP60/(Singapore) A-00003675 453070800230R Main Source
8 Signal Cable CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH CB-00008437 453010100380R 3 Main Source
9 Signal Cable CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS CB-00008190 453030300370R 2 Main Source
10 PC Board Main Board PCBA,IF/B,LA2,W/O SPK,LP23B2-522 ROHS B-00010487 79P231300501R Main Source
11 Assembly: [All Power Board PCBA,PI/B,W/O SPK,LP21A8-622 ROHS B-00010256 795361400601R Main Source
12 boards or PCBA] Key Pad PCBA,KEYPAD/B,LP21A8-622 ROHS B-00010257 795361500600R Main Source
13 Key Pad PCBA,FUNTION KEY/B,LP21A8-622 ROHS B-00010258 795361500601R Main Source
14 LED Board PCBA,LED CON/B,LP23B2-622 ROHS B-00010488 795620500600R Main Source
15 Cabinets: Front Bezel ASSY BEZEL W/SPK VX2450 C-00010372 71403P23B200R 1 Main Source
16 [Front Bezel, All Back Cover ASSY BACK CVOER W/O SPK W/DVI VX2450 C-00010373 71405P23B201R Main Source
17 Covers, Base/Stand Base Assembly ASSY BASE VX2450 C-00010374 71402P23B200R 3 Main Source
18 Assembly] Stand Assembly ASSY STAND VX2450 C-00010375 71401P23B200R 4 Main Source
19 Cables: [All internal Flat Cable HRN LVDS FFC 30P 237mm W/CORE CB-00009568 4303030040U0R Main Source
20 Cables/wires] Wire HRN ASS'Y 2x4P to 8P 90mm UL1571#28 CTD CB-00009569 4303008044E0R Main Source
Documentation:[Qui
21 ck Start Guide, CD Qucik Start Guide (QSG) KIT ASSY WW VX2450W-LP23B2 DC-00010471 703010003100R 5 Main Source
Rom, Label/Sticker]
Electronic
22 Components:[LCD Panel LCP 23.6"M236H3-LA2-902(A)(CMO) HF(CMO 902) E-00010229 631102240500H Main Source
Panel, Speaker, and
all Electronic
23 Packing Material: Carton CARTON,VX2450W-LP23B2 P-00010436 50602P23B200R 12 Main Source
24 [Box, Foam, Bags] Cushion CUSHION,EPS-L , LP23B2 P-00010437 50610LP23B01R 8 Main Source
25 Cushion CUSHION,EPS-R , LP23B2 P-00010438 50610LP23B02R 1 Main Source
26 Cushion CUSHION,EPS-M , LP23B2 P-00010439 50610LP23B00R 7 Main Source
27 Plactic Bag BAG,PLASTIC，EPE+PE,L500xW670xT0.55mm,LP P-00009399 506120010900R 4 Main Source
Plastics: [Pedestal,
29 stand/neck, Plate, Pedestal ASSY BASE VX2450 PL-00008888 71402P23B200R 3 Main Source
Button, etc.]
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is
to eliminate repeated cross checks of each item between this version and prior versions.
Notice: 1. For some special parts, some photos for identification purpose may be asked by request
2. For all internal cables, there must be some wordings on the "Description" column about where the cable is used (connecting to which two parts)
3. All internal cables/wires should be put in the "Cables" category
4. All external cables should be put in the "Accessories" category
5. Parts relationship (Main/Second source or 1/2/3/4) should be added in the "Compatibility" column
6. If any part for certain product isn't listed in the form, supplier/PE can add it themselves and keep the part name unified.

RECOMMENDED SPARE PARTS LIST (VX2450WM-LED)
Rev:1a
Serial No. Prefix: S4Z
Item Category Part Name Description ECR/ECN ViewSonic P/N Ref. P/N Ref. NO Compatibility
1 Accessories: Power Cord PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx(USA) A-00008111 453070800150R 6 Main Source
2 [Adapter, Remote Power Cord PWRCORD 7A/125V BLK 6FT CNS VCTF 3Gx0.75(TWN) A-00006733 453070800480R Main Source
3 Controller, Power Power Cord PWR CORD 16A/250V BLK 6FT VDE,H05VV-F 3G(Europe) A-00008279 453070801190R Main Source
4 Cord, External Power Cord PWRCORD 10A/250V BLACK 6FT SAA,H05W-F/3G(Australia) A-00003671 453070800420R Main Source
5 Cables] Power Cord PWRCORD 16A/250V BLK 6FT KTL,H05VV-F 3Gx(Korea) A-00006734 453070800500R Main Source
6 Power Cord PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx0.(China) A-00005255 453070800170R Main Source
7 Power Cord PWRCORD 5A/250V BLK 6FT UK3Gx.75mm(SP60/(Singapore) A-00003675 453070800230R Main Source
8 Signal Cable CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH CB-00008437 453010100380R 3 Main Source
9 Signal Cable CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS CB-00008190 453030300370R 2 Main Source
10 Signal Cable CABLE AUDIO 1P 6FT BLACK/GREEN CP03B06P0 CB-00008002 453030300120R 7 Main Source
11 PC Board Main Board PCBA,IF/B,LA2,W/SPK,LP23B2-522 ROHS B-00010489 79P231300500R Main Source
12 Assembly: [All Power Board PCBA,PI/B,W/SPK,LP21A8-622 ROHS B-00010261 795361400600R Main Source
13 boards or PCBA] Key Pad PCBA,KEYPAD/B,LP21A8-622 ROHS B-00010257 795361500600R Main Source
14 Key Pad PCBA,FUNTION KEY/B,LP21A8-622 ROHS B-00010258 795361500601R Main Source
15 LED Board PCBA,LED CON/B,LP23B2-622 ROHS B-00010488 795620500600R Main Source
16 Cabinets: [Front Front Bezel ASSY BEZEL W/SPK VX2450 C-00010372 71403P23B200R 1 Main Source
17 Bezel, All Covers, Back Cover ASSY BACK CVOER W/SPK W/DVI VX2450 C-00010378 71405P23B200R 7 Main Source
19 Base/Stand Stand Assembly ASSY STAND VX2450 C-00010375 71401P23B200R 4 Main Source
20 Cables: [All internal Flat Cable HRN LVDS FFC 30P 237mm W/CORE CB-00009568 4303030040U0R Main Source
21 Cables/wires] Wire HRN ASS'Y 2x4P to 8P 90mm UL1571#28 CTD CB-00009569 4303008044E0R Main Source
Documentation:
22 [Quick Start Guide, Qucik Start Guide (QSG) KIT ASSY WW VX2450WM-LP23B2 DC-00010472 703010003200R 5 Main Source
CD Rom,
Label/Sticker]
23 Electronic Speaker Speaker 2.5W 4Ω 50&70mm R/B/G W/CASE E-00010090 618100200790R Main Source
24 Components: [LCD Panel LCP 23.6"M236H3-LA2-902(A)(CMO) HF(CMO 902) E-00010229 631102240500H Main Source
25 Packing Material: Carton CARTON,VX2450WM-LP23B2 P-00010440 50602P23B201R 13 Main Source
26 [Box, Foam, Bags] Cushion CUSHION,EPS-L , LP23B2 P-00010437 50610LP23B01R 9 Main Source
27 Cushion CUSHION,EPS-R , LP23B2 P-00010438 50610LP23B02R 1 Main Source
28 Cushion CUSHION,EPS-M , LP23B2 P-00010439 50610LP23B00R 8 Main Source
29 Plactic Bag SEALED BAG ADHESIVE 330x230mm LE1918 P-00010441 506120100500R Main Source
Plastics: [Pedestal,
29 stand/neck, Plate, Pedestal ASSY BASE VX2450 PL-00008888 71402P23B200R 3 Main Source
Button, etc.]
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate
repeated cross checks of each item between this version and prior versions.
Notice: 1. For some special parts, some photos for identification purpose may be asked by request
2. For all internal cables, there must be some wordings on the "Description" column about where the cable is used (connecting to which two parts)
3. All internal cables/wires should be put in the "Cables" category
4. All external cables should be put in the "Accessories" category
5. Parts relationship (Main/Second source or 1/2/3/4) should be added in the "Compatibility" column
6. If any part for certain product isn't listed in the form, supplier/PE can add it themselves and keep the part name unified.

BOM LIST ( VX2450W-LED )
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty
1 A-00008111 453070800150R PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx 100 PC
2 CB-00008190 453030300370R CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS 100 PC
3 CB-00008437 453010100380R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH 100 PC
4 NA 71300P23B200R ASSY,PACKING,VSA,VX2450W-LP23B2 100 PC
5 P-00010437 50610LP23B01R CUSHION,EPS-L , LP23B2 100 PC
6 P-00010438 50610LP23B02R CUSHION,EPS-R , LP23B2 100 PC
7 P-00010439 50610LP23B00R CUSHION,EPS-M , LP23B2 100 PC
8 NA 506431008200R FILM,PROTECTION,UNPRINTED,555x327x0.1mm, 100 PC
9 P-00009399 506120010900R BAG,PLASTIC，EPE+PE,L500xW670xT0.55mm,LP 100 PC
10 P-00010436 50602P23B200R CARTON,VX2450W-LP23B2 100 PC
11 NA 50642P23B200R LBL RATING,VX2450W-LP23B2 100 PC
12 NA 506440002300R LABEL,BLANK,76.2x76.2mm,LE1709(UPC) 100 PC
13 NA 506440002400R LABEL,BLANK,50x25mm,LE1709(S/N) 100 PC
14 NA 506440002600R LABEL,BLANK,210x65mm,LE1709(PALLET) 5 PC
15 DC-00010471 703010003100R KIT ASSY WW VX2450W-LP23B2 100 PC
16 NA 50653P23B200R MNL USER'S(CD) ,VX2450WM-W LP23B2 100 PC
17 NA 50652E18DB04R QSG WW-VA1931w ,LE18DB 100 PC
18 NA 50650P21A800R BASE ATTCHMENT,VX2250wm-LP21A8 100 PC
19 NA 506420405200R INSERT SHEET, 1920*1080,LE21N1 100 PC
20 NA 71301P23B202R ASSY,PACK,SEA,20&40STD,USA,VX2450WM-LP23 100 PC
21 NA 506150014800R PALLET,L1219xW1016xH120mm,LE23R2 2.5 PC
22 NA 506039010470R CORNER PAPER 2080x40x40xT5mm 10 PC
23 NA 506039000100R CORNER PAPER,1000X50X50XT5MM 5 PC
24 NA 506039005400R CORNER PAPER 800x50x50xT5mm LE1512 5 PC
25 NA 506036005140R CARDBOARD, L1100*W 890*T5MM, LF15F9 2.5 PC
26 NA 506036006600R CARDBOARD,L1200XW 1000XT7 LE22M1 2.5 PC
27 NA 506431000300R FILM,PE 500mmx900M ROHS 0.36 ROL
28 NA 506380002100R TAPE WRAPPING TYPE(VIEWSONIC) 50mmx75M L 0.88 ROL
29 NA 506120100500R SEALED BAG ADHESIVE 330x230mm LE1918 2.5 PC
30 NA 50677P248400R INSERT CARTON 655*95*497(H)mm,LP2484 20 PC
32 NA 71301P23B203R ASSY,PACK,AIR,20&40STD,USA,VX2450WM-LP23 0 PC
33 NA 506150014800R PALLET,L1219xW1016xH120mm,LE23R2 0 PC
36 NA 506036005140R CARDBOARD, L1100*W 890*T5MM, LF15F9 0 PC
37 NA 506036006600R CARDBOARD,L1200XW 1000XT7 LE22M1 0 PC
38 NA 506431000300R FILM,PE 500mmx900M ROHS 0 ROL
39 NA 506380002100R TAPE WRAPPING TYPE(VIEWSONIC) 50mmx75M L 0 ROL
40 NA 506120100500R SEALED BAG ADHESIVE 330x230mm LE1918 0 PC
43 NA 71407P23B202R ASSY FINAL(B,LA2-902/A/Z)W/O S,LP23B2-52 100 PC
44 C-00010373 71405P23B201R ASSY BACK CVOER W/O SPK W/DVI VX2450 100 PC
45 NA 50102P23B201R BACK COVER W/O SPK W/DVI VX2450 100 PC
46 NA 502020100700R LOCK SHEET,LP2259 100 PC
47 NA 502090105600R VESA,LE23W2 400 PC
48 C-00010372 71403P23B200R ASSY BEZEL W/SPK VX2450 100 PC
49 NA 75001P23B200R SUB-ASSY BEZEL W/SPK VX2450 100 PC
50 NA 50101P23B200R BEZEL VX2450 100 PC
51 NA 50118P23B200R TRANSPARENT DECORATION VX2450 100 PC
52 NA 75003P21A801R SUB-ASSY,POWER BUTTON,LP21A8 100 PC
53 NA 50103P21A800R POWER BUTTON,LP21A8 100 PC
54 NA 75003P21A800R SUB-ASSY,POWER BUTTON RING,LP21A8 100 PC

55 NA 50119P21A800R POWER BUTTON RING,LP21A8 100 PC
56 NA 50683LP23B00R PROTECT-FILM,BEZEL,LP23B2 100 PC
57 C-00010375 71401P23B200R ASSY STAND VX2450 100 PC
58 NA 50126P23B200R STAND VX2450 100 PC
59 NA 71411P23B200R ASSY HINGE VX2450 100 PC
60 NA 50202P21A801R BRACKET,STAND,INL,LP21A8 100 PC
61 NA 509212606110R SCREW,F,CROSS,T4*6,Zn,ROHS(5.8~6.2) 200 PC
62 NA 509412610500R SCREW,B,CROSS,T.T-4*10,BLK ,ROHS 200 PC
63 PL-00008888 71402P23B200R ASSY BASE VX2450 100 PC
64 NA 50124P23B200R BASE VX2450 100 PC
65 NA 509012306800R SCREW,M4*9,Zn (WITH MANUAL),LP2479 100 PC
66 NA 503020006300R RUBBER FOOT L14.8*W9.6*T3.5mm ,LE19E3 500 PC
68 NA 509416608500R SCREW,B,CROSS,M4*8,BLK 200 PC
69 NA 71408P23B202R ASSY PANEL(LA2-902/A/Z)W/O S,LP23B2-522( 100 PC
70 NA 70106P23B201R ASSY CHASSIS W/O SPK W/DVI INL VX2450 100 PC
71 NA 50209P21A800R CHASSIS,DUAL,W/O SPK ,INL,LP21A8 100 PC
72 NA 51103P21A800R INSULATOR,MYLAR,17x13xT0.3mm,LP21A8 100 PC
74 NA 50202P23B200R BRACKET HINGE VX2450 100 PC
75 NA 509000000700R BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RO 400 PC
76 NA 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc 800 PC
77 NA 506381000700R TAPE,ACE,45mmx30M(PC=10x45mm) 300 PC
78 B-00010487 79P231300501R PCBA,IF/B,LA2,W/O SPK,LP23B2-522 ROHS 100 PC
79 B-00010256 795361400601R PCBA,PI/B,W/O SPK,LP21A8-622 ROHS 100 PC
80 B-00010257 795361500600R PCBA,KEYPAD/B,LP21A8-622 ROHS 100 PC
81 B-00010258 795361500601R PCBA,FUNTION KEY/B,LP21A8-622 ROHS 100 PC
82 B-00010488 795620500600R PCBA,LED CON/B,LP23B2-622 ROHS 100 PC
83 E-00010229 631102240500H LCP 23.6"M236H3-LA2-902(A)(CMO) HF 100 PC
84 NA 631102240501H LCP 23.6"M236H3-LA2-902(Z)(CMO) HF 0 PC
85 CB-00009568 4303030040U0R HRN LVDS FFC 30P 237mm W/CORE 100 PC
86 NA 4303012003P0R HRN FFC 12P 0.5Pitch 653mm 100 PC
87 CB-00009569 4303008044E0R HRN ASS'Y 2x4P to 8P 90mm UL1571#28 CTD 100 PC
88 NA 430300600770R HRN ASS'Y 5P to 6P 140mm UL1571#28 CTD 100 PC
89 NA 4303010020G0R HRN ASS'Y 2*5P to 2*5P 80mm UL1571#28 100 PC
90 NA 511150103300R FOIL,AL.,DOUBLE COND.,30x12x0.07mm, LE19 100 PC
91 NA 511150101800R FOIL,AL.,DOUBLE COND.,60x35xT0.07mm, LE2 100 PC

BOM LIST ( VX2450WM-LED)
Rev: 1a
1 A-00008111 453070800150R PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx 100 PC
2 CB-00008190 453030300370R CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS 100 PC
3 CB-00008002 453030300120R CABLE AUDIO 1P 6FT BLACK/GREEN CP03B06P0 100 PC
4 CB-00008437 453010100380R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH 100 PC
5 NA 71300P23B207R ASSY,PACKING,VSA,VX2450WM-LP23B2 100 PC
6 P-00010437 50610LP23B01R CUSHION,EPS-L , LP23B2 100 PC
7 P-00010438 50610LP23B02R CUSHION,EPS-R , LP23B2 100 PC
8 P-00010439 50610LP23B00R CUSHION,EPS-M , LP23B2 100 PC
9 NA 506431008200R FILM,PROTECTION,UNPRINTED,555x327x0.1mm, 100 PC
10 NA 506120010900R BAG,PLASTIC，EPE+PE,L500xW670xT0.55mm,LP 100 PC
11 P-00010440 50602P23B201R CARTON,VX2450WM-LP23B2 100 PC
12 NA 50642P23B201R LBL RATING,VX2450WM-LP23B2 100 PC
13 NA 506440002300R LABEL,BLANK,76.2x76.2mm,LE1709(UPC) 100 PC
14 NA 506440002400R LABEL,BLANK,50x25mm,LE1709(S/N) 100 PC
15 NA 506440002600R LABEL,BLANK,210x65mm,LE1709(PALLET) 5 PC
16 DC-00010472 703010003200R KIT ASSY WW VX2450WM-LP23B2 100 PC
17 NA 50653P23B200R MNL USER'S(CD) ,VX2450WM-W LP23B2 100 PC
18 NA 50652E18DB06R QSG WW-VA1931wm ,LE18DB 100 PC
19 NA 50650P21A800R BASE ATTCHMENT,VX2250wm-LP21A8 100 PC
20 NA 506420405200R INSERT SHEET, 1920*1080,LE21N1 100 PC
21 NA 71301P23B202R ASSY,PACK,SEA,20&40STD,USA,VX2450WM-LP23 100 PC
22 NA 506150014800R PALLET,L1219xW1016xH120mm,LE23R2 2.5 PC
23 NA 506039010470R CORNER PAPER 2080x40x40xT5mm 10 PC
26 NA 506036005140R CARDBOARD, L1100*W 890*T5MM, LF15F9 2.5 PC
27 NA 506036006600R CARDBOARD,L1200XW 1000XT7 LE22M1 2.5 PC
28 NA 506431000300R FILM,PE 500mmx900M ROHS 0.36 ROL
29 NA 506380002100R TAPE WRAPPING TYPE(VIEWSONIC) 50mmx75M L 0.88 ROL
30 P-00010441 506120100500R SEALED BAG ADHESIVE 330x230mm LE1918 2.5 PC
33 NA 71301P23B203R ASSY,PACK,AIR,20&40STD,USA,VX2450WM-LP23 0 PC
34 NA 506150014800R PALLET,L1219xW1016xH120mm,LE23R2 0 PC
37 NA 506036005140R CARDBOARD, L1100*W 890*T5MM, LF15F9 0 PC
38 NA 506036006600R CARDBOARD,L1200XW 1000XT7 LE22M1 0 PC
39 NA 506431000300R FILM,PE 500mmx900M ROHS 0 ROL
40 NA 506380002100R TAPE WRAPPING TYPE(VIEWSONIC) 50mmx75M L 0 ROL
41 P-00010441 506120100500R SEALED BAG ADHESIVE 330x230mm LE1918 0 PC
44 NA 71407P23B203R ASSY FINAL(B,LA2-902/A/Z)W/S,LP23B2-522( 100 PC
45 C-00010378 71405P23B200R ASSY BACK CVOER W/SPK W/DVI VX2450 100 PC
46 NA 50102P23B200R BACK COVER W/SPK W/DVI VX2450 100 PC
47 NA 502020100700R LOCK SHEET,LP2259 100 PC
48 NA 502090105600R VESA,LE23W2 100 PC
49 C-00010372 71403P23B200R ASSY BEZEL W/SPK VX2450 100 PC
50 NA 75001P23B200R SUB-ASSY BEZEL W/SPK VX2450 100 PC
51 NA 50101P23B200R BEZEL VX2450 100 PC
52 NA 50118P23B200R TRANSPARENT DECORATION VX2450 100 PC
53 NA 75003P21A801R SUB-ASSY,POWER BUTTON,LP21A8 100 PC
54 NA 50103P21A800R POWER BUTTON,LP21A8 100 PC
55 NA 75003P21A800R SUB-ASSY,POWER BUTTON RING,LP21A8 100 PC

56 NA 50119P21A800R POWER BUTTON RING,LP21A8 100 PC
57 NA 50683LP23B00R PROTECT-FILM,BEZEL,LP23B2 100 PC
58 C-00010375 71401P23B200R ASSY STAND VX2450 100 PC
59 NA 50126P23B200R STAND VX2450 100 PC
60 NA 71411P23B200R ASSY HINGE VX2450 100 PC
61 NA 50202P21A801R BRACKET,STAND,INL,LP21A8 100 PC
62 NA 509212606110R SCREW,F,CROSS,T4*6,Zn,ROHS(5.8~6.2) 200 PC
64 PL-00008888 71402P23B200R ASSY BASE VX2450 100 PC
65 NA 50124P23B200R BASE VX2450 100 PC
66 NA 509012306800R SCREW,M4*9,Zn (WITH MANUAL),LP2479 100 PC
67 NA 503020006300R RUBBER FOOT L14.8*W9.6*T3.5mm ,LE19E3 500 PC
69 NA 509416608500R SCREW,B,CROSS,M4*8,BLK 200 PC
70 NA 71408P23B203R ASSY PANEL(LA2-902/A/Z)W/S,LP23B2-522(VX 100 PC
71 NA 70106P23B200R ASSY CHASSIS W/SPK W/DVI INL VX2450 100 PC
72 NA 50209P21A801R CHASSIS,DUAL,W/SPK INL,LP21A8 100 PC
75 NA 50202P23B200R BRACKET HINGE VX2450 100 PC
76 NA 509000000700R BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RO 400 PC
77 NA 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc 800 PC
78 NA 506381000700R TAPE,ACE,45mmx30M(PC=10x45mm) 300 PC
79 B-00010489 79P231300500R PCBA,IF/B,LA2,W/SPK,LP23B2-522 ROHS 100 PC
80 B-00010261 795361400600R PCBA,PI/B,W/SPK,LP21A8-622 ROHS 100 PC
81 B-00010257 795361500600R PCBA,KEYPAD/B,LP21A8-622 ROHS 100 PC
82 B-00010258 795361500601R PCBA,FUNTION KEY/B,LP21A8-622 ROHS 100 PC
83 B-00010488 795620500600R PCBA,LED CON/B,LP23B2-622 ROHS 100 PC
84 E-00010229 631102240500H LCP 23.6"M236H3-LA2-902(A)(CMO) HF 100 PC
85 NA 631102240501H LCP 23.6"M236H3-LA2-902(Z)(CMO) HF 0 PC
86 CB-00009568 4303030040U0R HRN LVDS FFC 30P 237mm W/CORE 100 PC
87 NA 4303012003P0R HRN FFC 12P 0.5Pitch 653mm 100 PC
88 CB-00009569 4303008044E0R HRN ASS'Y 2x4P to 8P 90mm UL1571#28 CTD 100 PC
89 NA 430300600770R HRN ASS'Y 5P to 6P 140mm UL1571#28 CTD 100 PC
90 NA 4303010020G0R HRN ASS'Y 2*5P to 2*5P 80mm UL1571#28 100 PC
91 NA 511150101800R FOIL,AL.,DOUBLE COND.,60x35xT0.07mm, LE2 100 PC
92 NA 511150103300R FOIL,AL.,DOUBLE COND.,30x12x0.07mm, LE19 100 PC
93 E-00010090 618100200790R Speaker 2.5W 4Ω 50&70mm R/B/G W/CASE 100 PC

* Reader’s Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous
improvement of our products. We would appreciate your completion of the Assessment Matrix below,
for return to ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
Unit Excellent Good Fair Bad
1. Precautions and Safety Notices
2. Specification
3. Front Panel Function Control Description
4. Electronic Circuit Theory

5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Block Diagrams
8. Schematic Diagrams
9. PCB Layout Diagrams
10. Exploded Diagram and Exploded Parts List
11. Recommended Spare Parts List
B. Are you satisfied with this Service Manual?

Item Excellent Good Fair Bad
1. Service Manual Content
2. Service Manual Layout
3. The form and listing
C. Do you have any other opinions or suggestions regarding this service manual?
Reader’s basic dada:

Name: Title:
Company:
Add:
Tel: Fax:
E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile
1-909-839-7943.

Viewsonic - vx2450w WM Led 1 vs13518 1w 2w PDF

Uploaded by

Copyright:

Available Formats

Viewsonic - vx2450w WM Led 1 vs13518 1w 2w PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Viewsonic - vx2450w WM Led 1 vs13518 1w 2w PDF

Uploaded by

Copyright:

Available Formats

Service Manual

(VX2450W_WM-LED-1 SM Rev. 1a Jul. 2010)

Revision SM Editing Date ECR Number Description of Changes Editor

1a G G 07/21/10 Initial Release Sophia Kao

ViewSonic Corporation 1 Confidential - Do Not Copy VX2450W/WM-LED-1

1. Precautions and Safety Notices ...................................................................................... 3

3. Front Panel Function Control Description ................................................................... 22

4. Electronic Circuit Theory................................................................................................. 39

5. Adjusting Procedure ........................................................................................................ 43

6. Troubleshooting Flow Chart ........................................................................................... 71

7. Block Diagrams .............................................................................................................. 77

8. Schematic Diagrams ...................................................................................................... 78

9. PCB Layout Diagrams .................................................................................................... 84

10. Exploded Diagram And Spare Parts List...................................................................... 88

11. Recommended Spare Parts List .................................................................................. 92

ViewSonic Corporation 2 Confidential - Do Not Copy VX2450W/WM-LED-1

2. PRODUCT SAFETY NOTICE

ViewSonic Corporation 3 Confidential - Do Not Copy VX2450W/WM-LED-1

ViewSonic Corporation 4 Confidential - Do Not Copy VX2450W/WM-LED-1

Sync Separate Sync / Composite Sync / SOG

ViewSonic Corporation 6 Confidential - Do Not Copy VX2450W/WM-LED-1

7 POWER Voltage AC 100-240V (Universal); 50/60 Hz

8 ERGONO Tilt 20 ~ -5 degrees

ViewSonic Corporation 7 Confidential - Do Not Copy VX2450W/WM-LED-1

[Up] or [Dn] : To immediately activate Contrast

[ 1 ] + [ 2 ] : Toggle 720x400 and 640x400 mode

ViewSonic Corporation 8 Confidential - Do Not Copy VX2450W/WM-LED-1

ViewSonic Corporation 9 Confidential - Do Not Copy VX2450W/WM-LED-1

ViewSonic Corporation 10 Confidential - Do Not Copy VX2450W/WM-LED-1

(Detached cable; refer the Appendix A)

ViewSonic Corporation 11 Confidential - Do Not Copy VX2450W/WM-LED-1

Screen Protector Mylar Yes

ViewSonic Corporation 12 Confidential - Do Not Copy VX2450W/WM-LED-1

Test Resolution & Frequency 1920x1080@ 60Hz

2.4 Video Interface

Input Connector (refer the Appendix A) Analog = DB-15 (Analog)

ViewSonic Corporation 13 Confidential - Do Not Copy VX2450W/WM-LED-1

2.6 Power Supply

Internal Power Supply TBD

Power Supply Transient Immunity Shall be able to withstand an ANSI/IEEE

(Refer to EN55024:1998 / CISPR24.1997 /

ViewSonic Corporation 14 Confidential - Do Not Copy VX2450W/WM-LED-1

Mode LED Power Consumption

Recovery Time On Mode = N/A, Active Off < 3 sec

2.7 Electrical Requirement

ViewSonic Corporation 15 Confidential - Do Not Copy VX2450W/WM-LED-1

ViewSonic Corporation 16 Confidential - Do Not Copy VX2450W/WM-LED-1

1024 x 768 @ 60 Hz, 48.4 KHz v v v v DMT;

ViewSonic Corporation 17 Confidential - Do Not Copy VX2450W/WM-LED-1

ViewSonic Corporation 18 Confidential - Do Not Copy VX2450W/WM-LED-1

ViewSonic Corporation 19 Confidential - Do Not Copy VX2450W/WM-LED-1

*1. Tolerance ≧ ±2KHz (if no overlapping issue)

ViewSonic Corporation 20 Confidential - Do Not Copy VX2450W/WM-LED-1

ViewSonic Corporation 21 Confidential - Do Not Copy VX2450W/WM-LED-1

Note: Power Button, Button 1 and Button 2

3.2 Short Cuts Function from the button(s)

ViewSonic Corporation 22 Confidential - Do Not Copy VX2450W/WM-LED-1

[1] + [2] 1. Toggle 640x350@70Hz, 720x400@70Hz and 640x400@70Hz

[1] + [▲] OSD Lock