Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 154 views

    Sidewinder Assembly Manual

    Uploaded by

    Alberto
    The document provides assembly instructions for an Artillery 3D printer in 10 steps. It begins by fixing the XZ gantry and spool holder, then connecting sensors and stepper motors. Next, the carriage and sensors are attached and wheels are tensioned. Finally, the bed is leveled and the printer is powered on through the touch screen interface. Tips are provided on status lights and where to find support documentation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Sidewinder Assembly Manual

    Uploaded by

    Alberto
    154 views2 pages
    The document provides assembly instructions for an Artillery 3D printer in 10 steps. It begins by fixing the XZ gantry and spool holder, then connecting sensors and stepper motors. Next, the carriage and sensors are attached and wheels are tensioned. Finally, the bed is leveled and the printer is powered on through the touch screen interface. Tips are provided on status lights and where to find support documentation.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides assembly instructions for an Artillery 3D printer in 10 steps. It begins by fixing the XZ gantry and spool holder, then connecting sensors and stepper motors. Next, the carriage and sensors are attached and wheels are tensioned. Finally, the bed is leveled and the printer is powered on through the touch screen interface. Tips are provided on status lights and where to find support documentation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    154 views2 pages

    Sidewinder Assembly Manual

    Uploaded by

    Alberto
    The document provides assembly instructions for an Artillery 3D printer in 10 steps. It begins by fixing the XZ gantry and spool holder, then connecting sensors and stepper motors. Next, the carriage and sensors are attached and wheels are tensioned. Finally, the bed is leveled and the printer is powered on through the touch screen interface. Tips are provided on status lights and where to find support documentation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Artillery 3D Printer List 1 - Main Modules List 2 - Tools & Spares Step 1

    Fix the XZ gantry to the base with 4pcs of M4x45


    Sidewinder X1 screws as shown in picture。

                  M4x45 (5pcs) M4x45 (4pcs)

    30pin (1pc)
    20pin (1pc)

    Step 2 Step 3 Step 4 Step 5


    Fix the spool holder to the top of the printer, adjust Connect the filament runout sensor as shown in Fix the Z Endstop to the frame as shown in pictures Connect the Z Stepper Motors as shown in picture
    the width to fit the size of your filament spool. Make pictures below: below. The distance between the sensor top and base belows:
    sure the filament sensor is facing forward. top should be approx 75mm.

    Front

    75mm
    Step 6 Step 7 Step 8 Step 8
    Connect the X carriage and filament runout sensor as Connect the FFC to the board on X gantry. Adjust the tension of all the wheels on the machine. Try For wheels under build plate, push the wheels (on the
    shown in picture to the base. Caution: Please handle to turn the wheels without forcing them. If the wheel non-eccentric nut side) tight against the aluminum
    the flexible flat cable (FFC) with care, make sure it go turns freely or without much effort, then it is too loose. extrusion, then adjust the front and rear wheels by
    straight in when plugging them in, and make sure To tighten the wheels, rotate the eccentric nuts slightly turning the eccentric nuts, adjust the middle one at
    they’re sitting flush inside the connectors. until the wheel is snug against the frame. last.

    Step 9 Reset Button Tips For detailed warranty policy, please visit
    Now you can connect power and turn on the machine. With this reset button, it will reset the machine and During printing, the LED near the nozzle shows the h�ps://desk.zoho.com/portal/evnovo/kb/
    On the touch screen, go to Tools -> Heat to pre-heat cannot resume printing after pressed, so be careful current printing status: ar�cles/evnovo-limited-warranty
    the nozzle and bed. Wait till both heated up and not to press it accidentally.
    stead, go to Tools -> Level: - gradually change from blue to violet as the heated For support, please visit our �cke�ng page at
    bed gets to target temp. h�ps://desk.zoho.com/portal/evnovo/new�cket
    Move the nozzle to all four corners, adjust the hiehgt
    - gradually change from violet to red as the hotend
    by turning the knob below the bed. Slide a A4 paper
    gets to temperature.
    between the nozzle and the bed, adjust the height so Or you can visit our Facebook group at
    - change to white to illuminate work surface.
    that the piece of paper slides, with just a bit of drag,
    - change to green once print has finished. h�ps://www.facebook.com/groups/ar�lleryswx1/
    in all locations of the bed.
    - turn off after the print has finished.
    You may need to do the same process twice becasue
    adjustment in one corner will affect others.
    Also, you can change the LED color or turn it off
    through the TFT touch screen.

    Facebook Page Customer Support

    Artillery 3D Technology Co., Ltd.


    Last update date: 31 May, 2019
    This manual is updated to the date of printing.
    Please refer to the electronic version if in doubt.

    You might also like