ALKYLATION

UPGRADING PROCESSES
ALKYLATION
The addition of an alkyl group to any compound is an alkylation

reaction but in petroleum refining terminology the term alkylation is
used for the reaction of low molecular weight olefins with an
isoparaffin to form higher molecular weight isoparaffins. Although
alkylation can take place at high temperatures and pressures without
catalysts, the only processes of commercial importance involve low
temperature alkylation conducted in the presence of either sulfuric
or hydrofluoric acid. The reactions occurring in both processes are
complex and the product has a rather wide boiling range.By proper
choice of operating conditions, most of the product can be made to fall
within the gasoline boiling range with Motor Octane Numbers (MON)
from 88 to 94 and Research Octane Numbers (RON) from 94 to 99.
ALKYLATION REACTIONS
In alkylation processes using hydrofluoric or sulfuric acids as

catalysts, only isoparaffins with tertiary carbon atoms, such as
isobutane or isopentane, react with the olefins. In practice only
isobutane is used because isopentane has a sufficiently high octane
number and low vapor pressure to allow it to be effectively blended
directly into finished gasolines.
The process using sulfuric acid (See Fig. 20-11 Page 739 Nelson) as a
catalyst is much more sensitive to temperature than the hydrofluoric acid
(See Fig. 20-12 Page 739 Nelson) process.
With sulfuric acid it is necessary to carry out the reactions at 40 to 70°F
(5 to 21°C) or lower, to minimize oxidation reduction reactions which
result in the formation of tars and the evolution of sulfur dioxide. When
anhydrous hydrofluoric acid is the catalyst, the temperature is usually
limited to 100°F (38°C) or below.
THE PRINCIPAL REACTIONS which occur in alkylation are the

combinations of olefins with isoparaffins as follows:
ALKYLATION FEEDSTOCKS
Olefins and isobutane are used as alkylation unit feedstocks. The

chief sources of olefins are catalytic cracking and coking operations.
Butenes and propene are the most common olefins used, but pentenes are
included in some cases.
Some refineries include pentenes in alkylation unit feed to lower the FCC
gasoline vapor pressure and reduce the bromine number in the final
gasoline blend. Alkylation of pentenes is also considered as a way to
reduce the C5 olefin content of final gasoline blends and reduce its effects
on ozone reduction and visual pollution in the atmosphere. Olefins can be
produced by dehydrogenation of paraffins, and isobutane is cracked
commercially to provide alkylation unit feed. Hydrocrackers and catalytic
crackers produce a great deal of the isobutene used in alkylation but it is
also obtained from catalytic reformers, crude distillation, and natural gas
processing. In some cases, normal butane is isomerized to produce
additional isobutane for alkylation unit feed.
ALKYLATION PRODUCTS
In addition to the alkylate stream, the products leaving the alkylation unit
include the propane and normal butane that enter with the saturated and
unsaturated feed streams as well as a small quantity of tar produced by
polymerization reactions.
The product streams leaving an alkylation unit are: LPG grade propane
liquid, Normal butane liquid, C5-alkylate, and Tar.
CATALYSTS
Concentrated sulfuric and hydrofluoric acids are the only catalysts used
commercially today for the production of high octane alkylate gasoline
but other catalysts are used to produce ethylbenzene, cumene, and long-
chain (C12 to C16) alkylated benzenes.
PROCESS FLOW:
SULFURIC ACID ALKYLATION
1) The feeds – propylene, butylene, amylene, and fresh isobutane

enter the reactor and contact sulfuric acid with a concentration of 85 to
95%.
2) The reactor is divided into zones. Olefins are fed through distributors
to each zone, and sulfuric acid and isobutanes flow over baffles from one
zone to the next.
3) The reactor effluent goes to a settler, in which hydrocarbons separate

from the acid. The acid is returned to the reactor.
4) The hydrocarbons are washed with caustic and sent to fractionation.
5) The fractionation section comprises a depropanizer, a deisobutanizer,

and a debutanizer.
6) Alkylate from the deisobutanizer can go directly to motor-fuel

blending, or it can be reprocessed to produce aviation-grade gasoline.
Isobutane is recycled.
PROCESS FLOW:
HF ALKYLATION
1) Olefins and isobutane are dried and fed to a reactor, where the
alkylation reaction takes place over the HF catalyst.
2) The reactor effluent flows to a settler, where the acid phase

separates from the hydrocarbon phase.
3) The acid is drawn off and recycled.
4) The hydrocarbon phase goes to a deisobutanizer (DIB).
5) The overhead stream, containing propane, isobutane, and residual

HF, goes to a depropanizer (DeC3).
6) The depropanizer (DeC3) overhead goes to an HF stripper. It is

then treated with caustic and sent to storage.
7) Isobutane from the deisobutanizer (DIB) main fractionator is

recycled.
8) The bottom stream from the debutanizer goes to product

blending.
Hydrofluoric acid (HF) alkylation

ALKYLATION

Uploaded by

Copyright:

Available Formats

ALKYLATION

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ALKYLATION

Uploaded by

Copyright:

Available Formats

What are the main feedstocks and products of the alkylation process?

What are the main reactions that occur during alkylation?

UPGRADING PROCESSES

The addition of an alkyl group to any compound is an alkylation

In alkylation processes using hydrofluoric or sulfuric acids as

THE PRINCIPAL REACTIONS which occur in alkylation are the

Olefins and isobutane are used as alkylation unit feedstocks. The

1) The feeds – propylene, butylene, amylene, and fresh isobutane

3) The reactor effluent goes to a settler, in which hydrocarbons separate

4) The hydrocarbons are washed with caustic and sent to fractionation.

5) The fractionation section comprises a depropanizer, a deisobutanizer,

6) Alkylate from the deisobutanizer can go directly to motor-fuel

2) The reactor effluent flows to a settler, where the acid phase

3) The acid is drawn off and recycled.

4) The hydrocarbon phase goes to a deisobutanizer (DIB).

5) The overhead stream, containing propane, isobutane, and residual

6) The depropanizer (DeC3) overhead goes to an HF stripper. It is

7) Isobutane from the deisobutanizer (DIB) main fractionator is

8) The bottom stream from the debutanizer goes to product

You might also like