Quotation

Sugar Manufacturers Supply Corp.
Quote Number:
P.O. Box 6127
052318‐03
West Palm Beach, FL  33405 Quote Date:
May 23, 2018
Page:
Tel: (561) 585‐8679 Fax: (561) 585‐9891
1
Quoted to:
Consorcio Azucarero Central, S.A.
Ingenio Barahona
Av. Sarasota 
Esq Francisco Moreno Santo Doming
Rep. Dominicana
Customer ID Delivery Payment Terms
Barahona 9/24/18 Net 30 Days

Quantity Item Description Unit Price Extension

1.00 28BHC BA Goulds model VIT‐FFFM Size, 29,507.00 29,507.00

28BHC, CI W CD4MCU Imp, Bowl
OD&ID coated with Tnemec 141,
Marine suciton bearing
1.00 18ʺ Flngd Col 2.4375 18ʺ x 2.4375ʺ Flanged W/L Column 27,357.00 27,357.00
Assembly, 299.69ʺ in length,
Rubber Marine bearings max
spacing is 10ʹ, as with column.
Epoxy coating to the ID of column
1.00 18ʺ FF Head Head Assembly 18ʺ x24.5ʺ FF W/L 12,883.00 12,883.00
head, 150# flanges,Tnemec 141
Epoxy coating in ID & OD

Subtotal 69,747.00
Sales Tax
Total 69,747.00
 SUBMITTAL
Quote ID: 052318-03 QTY: 1
VIT-FFFM 28BHC, 1 Stage
 

 
PERFORMANCE ON DESIGN CURVE AT 1180 RPM
Shut Off Design [2] Run Out [5]
Flow (USGPM) 0.0 11000.0 0.0 Best Efficiency 85.60 % at 9375.0 USgpm
TDH-Bowl (ft) 183.0 101.0 0.0 Design Flow % BEP 117.33 %
TDH-Disch Flange ( ft) 178.0 91.1 - Pump Efficiency 76.97 %
Bowl Efficiency (%) - 81.40 - Overall Efficiency 0.00 %
Power (Hp) - 343.0 - Max Power (NOL) 343.0 Hp at 11115.0 USgpm
NPSHr (ft) [1] - 32.2 - Max Power (NOL) at Max Trim 420.0 Hp at 11669.0 USgpm
NPSH Margin (ft) [1] - 22.8 - Specified NPSH Ratio 1.1
Hydraulic Thrust(lb) 12535.5 6918.5 0.0 Thrust Load Power Loss 0.67377 Hp
Thrust (lb) 13260.8 7607.7 0.0 Total Flow Derate Factor 1.00
Pressure-Bowl (psi) 79.2 43.7 - Total Head Derate Factor 1.00
Pressure-Disch Flange (psi) 77.1 39.4 - Total Efficiency Derate Factor 1.00
Min Submergence (Inch) [3] - 97.88 - Actual Submergence 302.38 in
Friction Loss (ft) [4] - 5.18 - Shaft Friction Power Loss 0.48 Hp
Lineshaft Elongation (Inch) 0.02886 0.01593 - Min Flow (MCSF) 2344.0 USgpm
Column Elongation (Inch) 0.00000 0.00000 - kWh per 1000 gal 0.00000
Lateral (Inch) 0.15886 0.14593 - Impeller Running Clearance 0.13 in
[1] at 1st impeller eye [2] rated values [3] from bottom of pump [4] from bowl to disch flange [5] based on user entered TDH

OPERATING CONDITIONS
 

FLUID CHARACTERISTICS
Specified Flow 11000.00 USgpm Fluid Water
Specified TDH 100.00 ft Fluid Temperature 68.0 °F
Rated Speed 1180 RPM Specific Gravity 1.0000
Atmospheric Pressure 15 psi Viscosity 1.0017 cP
TPL 30.20 ft Vapor Pressure 0.3393 psi
Pumping Level 5.00 ft Density 62 lbs/ft³
NPSHa at 1st Impeller 55.0 ft
NPSHa at Grade 33.9 ft

MATERIALS & DIMENSIONS

Bowl Data Bowl Data
Bowl Material Epoxied Cast Iron Thrust K-Factor 68.5 Lb/Ft
Bowl Material Derate Factor 1.00 Bowl Pressure Limit 220 psi
Impeller Material Aluminum Bronze Available Lateral 0.87 in
Impeller Matl Derate Factor 1.00 Bowl Assembly Length (BL) 62.69 in
Bowl Shaft Material 316SS Disch Bowl Length OLS (L0) 3.81 in
Impeller Attachment Keyed Disch Bowl Length ELS (L2) 12.00 in
Key Material 416SS Bowl Shaft Diameter 2 11/16" [68.3 mm]
Discharge Bowl Material Not Included Impeller Balance Manufacturer's Standard
Suction Type Bell Impeller Design Enclosed
Suction Material Cast Iron Bowl Wear Ring Not Included
Bowl Bolting Material 316SS Impeller Wear Ring Not Included
Sand Collar Bronze Suction Pipe Diameter No Suction Pipe
Pipe Plug Iron Bowl Diameter (D) 26.88 in
Suction Bearing Bronze Bowl Length (L3) 22.00 in
Discharge Bowl Bearing Not Included Bowl Flange Thickness (E) 27.75 in
Intermediate Bowl Bearing Rubber with Phenolic Backing Strainer Length (SL) 23.94 in
Strainer Type Clip-On Bell Type Strainer Floor Clearance (X) 18.00 in
Strainer Material 316LSS Min Column Diameter 16 in
Tube Adapter Bearing Max Column Diameter 20 in
Not Included
Material Max Bowl Shaft Diameter 3.69 in
Impeller Trim 17.94 in Bowl Shaft Length 42.88 in
Max Impeller Trim 19.44 in Bowl Shaft Power Limit 608.81 Hp

  DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED

    Certified By    
Project
Tag
PO Number
Serial Number
 SUBMITTAL
Quote ID: 052318-03 QTY: 1
VIT-FFFM 28BHC, 1 Stage
   

Bowl Specials

Column Data Column Data

Column Type Flanged Column Bearing Options Not Included
Column Diameter 18" [457mm] Column Retainer Design Integral
Lineshaft Diameter 2 7/16 in [61.9 mm] Maximum Bearing Spacing 10 ft (3 m) Spacing
Column Bolting 316SS Max Column Section Length 120 in
Column Pipe Material Carbon Steel Number of Bearings 3
Lineshaft Material 316SS Fabrication Welding Option Not Included
Lineshaft Bearing Material Rubber with phenolic backing Column Length (COL) 299.69 in
Lineshaft Coupling Type Threaded Column Wall Thickness 0.37 in
Lineshaft Coupling Material 316SS Column Load -1585.7 lb
Column Loss 1.37 ft Lubrication Method Water (Open Lineshaft)
Column Velocity 15.11 ft/s Lineshaft Length 299.69 in
Column Flange Carbon steel Head Sleeve Not Included
Column Shaft Sleeve Not Included Lineshaft Power Limit 551 Hp
Column Bearing Retainer Not Applicable

Column Specials

Head Data Head Data

Head Type Type FF (Fabricated F-Head) Seal Mounted By Customer
Discharge Flange Rating 150 # Stuffing Box / Seal Hsg Bolt 316SS
Disch Flange Pressure Limit 285 psi Stuffing Box / Seal Hsg Brg Bronze
Head Design Two Piece Head Seal Housing Material Cast iron
Discharge Head Material Carbon steel Steel Sub Base Not Included
Headshaft Material 316SS Head Loss 3.80 ft
Headshaft Coupling Type Threaded 150# Disch Companion Flg Not Included
Headshaft Coupling Material 416SS 300 # Suct Convenience Flg No suction flange
Headshaft Diameter (BX) 2.44 in Column Hanger Flange Not Included
Discharge Head Size 18" [457mm] Head Sleeve Not Included
Discharge Head BD 24.5" [622mm] Head Bolting 316SS
Sealing Method Packing Split Gland 316SS
Packing Material Acrylic yarn and graphite Motor Stand Not included
Stuffing Box Material Cast iron Air Vacuum Valves Not Included
Tension Plate Not Included Fabrication Welding Option Not Included
Seal Provided By Customer

Head Specials

Motor Data Motor Data

Driver Type Vertical Hollow Shaft Motor Insulation Class
Motor Manufacturer Service Factor
Selected Motor Power Motor Provided By Customer
Motor Speed 1180 RPM Motor Mounted By Customer
Voltage HP Rating 350 Hp
Phase / Frequency Speed [Poles] 1200 rpm [6 pole]
Mfg Catalog Number
Enclosure
Motor Part Number
Motor Frame
Max power on design curve
Inverter Duty Driver Size Criteria
(NOL)
Steady Bushing
Motor Coupling

Motor Specials

DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED

Certified By
Project
  Tag
    PO Number
   
Serial Number
 SUBMITTAL
Quote ID: 052318-03 QTY: 1
VIT-FFFM 28BHC, 1 Stage
   
Coating Data Coating Data
Tnemec 141 (NSF): Epoxy Can ID Not Included
Bowl OD
applied to 8 mils min Tnemec 141 (NSF): Epoxy
Head ID
Tnemec 141 (NSF): Epoxy applied to 8 mils min
Column ID
applied to 8 mils min Tnemec 141 (NSF): Epoxy
Head OD
Tnemec 141 (NSF): Epoxy applied to 8 mils min
Column OD
applied to 8 mils min Enclosing Tube OD Not Included
Column Bearing Retainer Not Included Steel Sub Base Not Included

Testing Data

Miscellaneous Specials

Weight Data Weight Data

Total Bowl Weight 1550 lbs Unit Column Weight 130 lbs
Unit Bowl Weight 1500 lbs Head Weight 1402 lbs
Strainer Weight 50 lbs Total Weight 6202 lbs
Total Column Weight 3250 lbs Total Rotating Weight 645 lbs
 
INFO, WARNING & ERROR MESSAGES
Invalid is invalid
Key Material Invalid Key Material is invalid
Sand Collar Invalid Sand Collar is invalid
Steady Bushing Invalid A Steady Bushing is required for VHS motors greater than or equal to 100 Hp for pumps with a Packed Box or Tension Plate.

Our offer does not include specific review and incorporation of any Statutory or Regulatory Requirements and the offer is limited to the requirements of the
design specifications. Should any Statutory or Regulatory requirements need to be reviewed and incorporated then the Customer is responsible to identify those
and provide copies for review and revision of our offer.

Our quotation is offered in accordance with our comments and exceptions identified in our proposal and governed by our standard terms and conditions of sale –
Xylem Americas attached hereafter.

For units requiring performance test, all performance tests will be conducted per ANSI/HI 14.6 standards unless otherwise noted in the selection software
submittal documents. Test results meeting with grade 2B tolerances for pumps with a rated shaft power of 134HP or less and grade 1B for greater than 134HP will
be considered passing.

Customer is responsible for verifying that the recommendations made and the materials selected are satisfactory for the Customer's intended environment and
Customer's use of the selected pump. Customer is responsible for determining the suitability of Xylem recommendations for all operating conditions within
Customer's and/or End User's control. Xylem disclaims all warranties, express or implied warranties, including, but not limited to, warranties of merchantability
and fitness for a particular purpose and all express warranties other than the limited express warranty set forth in the attached standard terms and conditions of
sale – Xylem Americas attached hereafter.

Xylem does not guarantee any pump intake configuration. The hydraulic and structural adequacies of these structures are the sole responsibility of the Customer
or his representatives. Further, Xylem accepts no liability arising out of unsatisfactory pump intake field operating conditions. The Customer or his
representatives are referred to the Hydraulic Institute Standards for recommendations on pump intake design. To optimize the hydraulic design of a field pump
intake configuration, the Customer should strongly consider performing a detailed scale model pump intake study. However, the adequacies of these
recommendations are the sole responsibility of the Customer. 

DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED

Certified By
Project
  Tag
    PO Number
   
Serial Number
 OUTLINE DRAWING
Quote ID: 052318-03 QTY: 1
VIT-FFFM 28BHC, 1 Stage

 
 

DIMENSIONS PUMP DATA

G [Mounting Flange Dia] 43.75 in Column Diameter 18" [457mm]

J [Mounting Flange Hole 2 7/16 in [61.9
1.63 in Lineshaft Diameter
Dia] mm]
K [Mounting Hole Places] 16 11000.00
Specified Flow
H [Mounting Flange Bolt USgpm
40.50 in
Circle] Specified TDH 100.00 ft
BD Head [Discharge Head Pumping Level 5.00 ft
24.50 in
Base Dia] Motor Manufacturer
HH [Head Height] 50.00 in Vertical Hollow
Driver Type
AD [Mounting Flange Shaft Motor
2.00 in
Thickness] Selected Motor Power
DD [Disch Flange Stickout] 24.00 in Motor Speed 1180 RPM
DH [Disch Flange Height] 16.00 in Phase / Frequency
S [Hanger Flange
1.63 in Voltage
Stickdown Length]
R [Hanger Flange OD] 23.00 in
WEIGHTS
Column Length (COL) 299.69 in
COL [Column Diameter] 18.00 in Total Bowl Weight 1550 lbs
TPL [Total Pump Length] 362.38 in Unit Bowl Weight 1500 lbs
MIN SUB [Minimum Strainer Weight 50 lbs
97.88 in
Submergence] Total Column Weight 3250 lbs
MAX [Max Assembly OD] 28.38 in Unit Column Weight 130 lbs
BL [Bowl Assembly 1402 lbs
62.69 in Head Weight
Length]
Total Weight 6202 lbs
SL [Suction Length] 23.94 in
Total Rotating Weight 645 lbs
 

NOTES
1 Total Pump Length ± 1.0 inch.
2 Tolerance on all dimensions is .12 or ± .12
inch per 5 ft, whichever is greater.
3 All dimensions shown are in inches unless
otherwise specified.
4 Drawing not to scale.
5 ½” NPT – Gauge Conn (plugged)
6 Driver may be rotated at 90º intervals about
vertical centerline for details refer to driver
dimension drawing.
7 Refer to product IOM for impeller setting
requirements.
8 This assembly has been designed so that
its natural frequency responses avoid the
specific operating speeds by an adequate
safety margin. The design has assumed
the foundation to be rigid.

  DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED

    Certified By    
Project
Tag
PO Number
Serial Number
 CROSS SECTION DRAWING
Quote ID: 052318-03 QTY: 1
  VIT-FFFM 28BHC, 1 Stage

 
 

BILL OF MATERIALS
ITEM PART NAME CODE MATERIAL ASTM#
Head Assembly
608 Headshaft 2216 SST 316 A276
600 Head-Discharge 9645 Carbon Steel Fab A53
602 Sub Base N/A Not Included N/A
604 Nut – Adjusting 2242 Carbon Steel 1018 A108
605 Motor Stand NA NA NA
616 Housing 1003 Cast Iron Cl30 A48 CLASS 30B
617 Bearing-Housing 1618 Bronze Bismuth B584 Modified
618 Gland-Split 1203 SST 316 A744M
620 Packing 5026 Graphite Packing ML402-99
621 O-Ring 5302 Nitrile Buna N D4322
622 Slinger 5121 Rubber Epdm D3568
625 Tension Plate N/A Not Included N/A
637 Hanger Flange N/A Not Included N/A
648 Headshaft Sleeve N/A N/A N/A
608 Headshaft Coupling 2265 SST 416 A582M
730 Key-Motor Gib 2242 Carbon Steel 1018 A108
757 Screw-Gland Adj 2229 SST 316 A276
760 Head Bolting 2229 SST 316 A276
 

Column Assembly
637 Column Flange 9645 Carbon Steel Fab A53
642 Column Pipe 6501 Black Pipe Sch 40 A 53
646 Lineshaft 2216 SST 316 A276
649 Lineshaft-Coupling 5914 SST 316 Chrome B177
652 Retainer-Bearing N/A Not Applicable N/A
656 Lineshaft Bearing 6111 Rubber / Phenolic Cloth D2000
 

Bowl Assembly
660 Shaft - Bowl 2216 SST 316 A276
661 Discharge Bowl NA Not Included Not Included
664 Bearing - Discharge Bowl N/A Not Included N/A
668 Bearing Tube Adapt N/A Not Included N/A
670 Bowl - Intermediate 5853 Cast Iron Cl30 Epoxy A48
672 Bearing - Intermediate Bowl 6111 Rubber / Phenolic Cloth D2000
673 Impeller 1126 Bronze, Ni Al C95800 B148
674 Key-Impeller 2217 SST 416 A582M
680 Wear Ring-Bowl N/A Not Included N/A
681 Wear Ring - Impeller NA Not Included NA
688 Suction 1003 Cast Iron Cl30 A48 CLASS 30B
690 Bearing - Suction 1109 Bronze C90300 "G" Mod B584
692 Sandcollar 1109 Bronze C90300 "G" Mod B584
698 Strainer 3216 SST 316L A240
747 Pipe Plug 1046 Malleable Iron A197
760 Capscrew-Hex 2229 SST 316 A276
 

  DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED

    Certified By    
Project
Tag
PO Number
Serial Number
 PERFORMANCE CURVE
Quote ID: 052318-03 QTY: 1
VIT-FFFM 28BHC, 1 Stage

Specified NPSH available is insufficient for the pump.

CURVE DATA
Specified Flow 11000.00 USgpm Design Pressure (Disch Flange) 39.4 psi Specified NPSH Ratio 1.1
Specified TDH 100.00 ft Shut Off TDH (Bowl) 183.0 ft NPSH Margin at Design 22.8 ft
Motor Speed 1180 RPM Shut Off TDH (Disch Flange) 178.0 ft Min Submergence at Design 97.88 in
Atmospheric Pressure 15 psi Shut Off Pressure (Bowl) 79.2 psi Actual Submergence 302.38 in
TPL 30.20 ft Shut Off Pressure (Disch Flange) 77.1 psi Shaft Friction Power Loss 0.48 Hp
Pumping Level 5.00 ft Bowl Efficiency at Design 81.40 % Thrust Load Power Loss 0.67377 Hp
NPSHa at Grade 33.9 ft Best Efficiency 85.60 % Hydraulic Thrust at Design 6918.5 lb
NPSHa at 1st Impeller 55.0 ft BEP Flow 9375.0 USgpm Thrust at Design 7607.7 lb
Fluid Water Design Flow % BEP 117.33 % Hydraulic Thrust at Shut Off 12535.5 lb
Fluid Temperature 68.0 °F Pump Efficiency 76.97 % Thrust at Shut Off 13260.8 lb
Specific Gravity 1.0000 Friction Loss at Design 5.18 ft Bowl Material Epoxied Cast Iron
Viscosity 1.0017 cP Power at Design 343.0 Hp Bowl Material Derate Factor 1.00
Vapor Pressure 0.3393 psi NOL Power 343.0 Hp Impeller Material Aluminum Bronze
Density 62 lbs/ft³ Max Power (NOL) Flow 11115.0 USgpm Impeller Matl Derate Factor 1.00
Design Flow 11000.0 USgpm Max Power (NOL) at Max Trim 420.0 Hp Total Flow Derate Factor 1.00
Min Flow (MCSF) 2344.0 USgpm Max Power (NOL) Flow at Max Total Head Derate Factor 1.00
11669.0 USgpm
Design TDH (Bowl) 101.0 ft Trim Total Efficiency Derate Factor 1.00
Design TDH (Disch Flange) 91.1 ft Recommended Power 350.00 Hp Curve ID E6828BBPC0
Design Pressure (Bowl) 43.7 psi kWh per 1000 gal 0.00000
NPSHr at Design 32.2 ft

       DO NOT USE FOR CONSTRUCTION UNLESS CERTIFIED

    Certified By    
Project
Tag
PO Number
Serial Number