Kortek kt2914f

COLOR CRT MONITOR DOC.
NO KT-XX14X-SM
DATE 2004 .02. 02
REV. NO 0
REV. DATE -
SERVICE MANUAL
KT-2914F / KT-2914DF
KT-2114F / KT-2114DF
KORTEK CORPORATION
Downloaded from www.Manualslib.com manuals search engine

CONTENTS
1. PRECAUTIONS -------------------------------------------------- 3
2. PRODUCT SPECIFICATION -------------------------------- 6
3. OPERATING INSTRUCTION -------------------------------- 9
4. ADJUSTMENTS ------------------------------------------------ 11
5. TROUBLE SHOOTING GUIDE ---------------------------- 19
6. PART LIST ------------------------------------------------------- 29
7. BLOCK DIAGRAM -------------------------------------------- 34
8. CONNECTING DIAGRAM ----------------------------------- 35
9. SCHEMATIC ----------------------------------------------------- 36
10. PRINT CIRCUIT BOARD ---------------------------------- 37
-2-

1.Precautions
1-1. Safety precautions

Warnings : Service should not be attempted by anyone unfamiliar with the
necessary on this Monitor.
The followings are the necessary precautions to be observed before servicing.

1) For continued safety, do not attempt to modify the circuit board.
2) Disconnect the AC power before servicing.
3) When the chassis is operating, semiconductor heat sinks are potential
shock hazards.
1-1-1 Servicing the high voltage volume are CRT Warnings

A High Voltage volume replaced in the wrong direction may cause excessive
X-Ray emissions.
1) Adjust in order to 26KV with signal at Anode.
2) When the troubleshooting a monitor with excessively High Voltage, avoid
being unnecessarily close to the monitor. Do not operate the monitor for
longer than is necessary to locate the cause of excessive voltage.
3) Excessive High Voltage can produce potentially hazardous X-Ray RADIA-
TION. To avoid such hazards, the high voltage must be above the
specified limit. The nominal value of the High voltage of this Monitor is
26KV ± 0.3KV at zero beam current(minimum brightness) under a 120V
AC power source. The High Voltage must not (under any circumstances)
exceed 29KV. Each time a monitor requires servicing, the High Voltage
should be checked following the High Voltage check procedure on this
manual. It is recommended the reading of the voltage be recorded as a
part of the service record. It is important to use an accurate and reliable
High Voltage meter.
4) When the High Voltage regulator is operating properly, there is no possib-
ility of an X-Ray problem.
5) The CRT is especially designed to prohibit X-ray emission. To ensure
continued X-ray protection, replace the CRT only with one that is the
same or equivalent type as the original.
6) Handle the CRT only when wearing shatterproof goggles and after completely.
7) Do not lift the CRT by the neck.
-3-

1-1-2. Fire and Shock Hazard
Before returning the monitor to the user,perform the following safety checks:
1) Inspect each lead dress to make certain that the leads are not pinched or
that hardware is not lodged between the chassis and other metal parts
in the monitor.
2) Inspect all protective devices such as nonmetallic control knobs, insulating
materials, cabinet backs, adjustment and compartment cover or shields
isolation resistor-capacitor networks, mechanical insulations, etc.
3) To be sure that no shock hazard exists, check for leakage current in the
following manner.
a. Plug the AC line cord directly into a 120 or 230 Volt AC outlet.
(Do not use an isolation transformer for this test)
b. Using two clip leads, connect a 1.5KΩ, 10Watt resistor paralleled by a
0.15Uf capacitor in serial with an exposed metal chassis part and a
known earth ground, such as an electrical conductor and electrical
ground connected to a earth ground.
c. Use a SSVM or VOM with 1000 ohms per-volt or sensitivity to measure
the AC voltage drop across the resistor.
d. Connect the resistor to an exposed metal part having a return path to
the chassis(metal cabinet, screw heads, knobs, shafts, escutcheon,etc)
and measure the AC voltage drop across the resistor.
e. Any reading of 5.25 volt RMS(this corresponds to 3.5 milliampere AC)
or more is excessive and indicates a potential shock hazard. Correct
the shock hazard before returning the monitor to the user.
(READING SHOULD)
NOT BE ABOVE
0.5mA
TEST ALL LEAKAGE

DEVICE
EXPOSED METAL CURRENT
UNDER
TEST SURFACES TESTER
2-WIRE
CORD
ALSO TEST WITH

PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
Earth
ground
Figure 1-1. Leakage Current Test Circuit
-4-

1-1-3. Product safety notices:
Some electrical and mechanical parts have special safety related characteristics
which are often not evident from visual inspection. The protection they give
may not be obtained by replacing them with components rated for higher volt-
age,wattage,etc. Parts that have special safety characteristics are identified by
△ on schematics and parts lists.
A substitute replacement that does not have the same safety characteristics
as the recommended replacement part might create shock, fire and or other
hazards. Product safety is under review continuously and new instructions
whenever appropriate.
1-2. Servicing Precautions
WARNING 1 : First read the "Safety Precaution" section of this manual. if
unforeseen circumstances create conflict between the servicing
precautions and safety precautions,always follow the safety
precautions.
WARNING 2 : A High Voltage volume replaced in the wrong direction may
cause excessive X-ray emissions.
WARNING 3 : An electrolytic capacitor installed with the wrong polarity might
explode.
1) Servicing precautions are printed on the chassis, and should be followed
closely
2) Always unplug the units AC power cord from the AC power source before
attempting to :(a) remove or reinstall any component or assembly, (b)
disconnect PCB plugs or connectors,(c) connect all test components in
parallel with an electrolytic capacitor.
3) after servicing, always check that the screws, components and wiring have
been correctly reinstalled. Make sure that the area around the serviced
part has not been damaged.
4) Check the insulation between the blades of the AC plug and accessible
conductive parts(examples:metal panels,input terminals and earphone jacks).
5) Never defeat any of the +B voltage interlocks. Do not apply AC power to
the unit(or any of its assemblies) unless all solid-state heat sinks are
correctly installed.
6) Always connect a test instruments ground lead to the instrument chassis
ground before connecting the lead; always remove the instruments lead last.
-5-

2. Product Specifications
2-1 SPECIFICATION
CDT KT-2914F KT-2914DF KT-2114DF KT-2114F
Tube 29"No rmal flat 29"Dyna flat 21"Dyna flat 21"No rmal flat
Tube Size(Diagonal) 730 mm(2 9") 730 mm(2 9") 550 mm(2 1") 550 mm(2 1")
Viewabl e S ize (Dia gonal ) 605 mm(2 7") 605 mm(2 7") 508 mm(2 0") 508 mm(2 0")
Dot Pitch 0.79㎜ (H) 0.79㎜ (H) 0.74㎜ (H) 0.74㎜ (H)
Deflection Angle 90° 90° 90° 90°
Focusing Method Sing le Double Sing le Sing le
Normal (H*V) 550 *40 0 550 *40 0 400 *30 0 400 *30 0
Display Area (mm)
Maximum (H*V) 580 *41 0 580 *41 0 415 *31 0 415 *31 0
Bandwidth Maximum 50MHz

Scanning Frequency Horizontal 15-40KHz
(Auto Scanning) Vertical 50-120Hz
Microprocessor User Saving Mode 6 Modes
Digital Position,Size,Pincushion,Trapezoid,H/Vcorner,
User Control Pin-B,Trapezoid,Parallel,Tilt,Moire,Zoom
Display Color Temperature,Recall,Manual Degauss
Language Eng/Ger/Fra/Esp/Port
Display color Color Temperature 9300 °
K, 6500°
K, User Color
Resolution Maximum Mode 800 X 600 @ 60Hz
Signal Input Connect 15 pin D-sub(Female) or Option(6Pin, 5Pin)

Safety cUL,CE,DHHS
Safety & EMC
EMC FCC,CE
Power Voltage AC 90-264V, 60 / 50 ±3Hz
Power Consumption Nomal Operation ≤120 Watts
Input Current Operating :≤ 1.5Amps rms.
at 120V Turn on :≤ 30Amps Peak.
Input Current Operating :≤ 0.8Amps rms.

at 240V Turn on :≤ 60Amps Peak.
Horizontal : 5%
Linearity Cross Pattern
Vertical : 5%
Temperature Operating : 0 to +40℃
Storage : -40 to +60℃
Environment
Humidity Operating : 10 to 85%
Storage : 5 to 95%
-6-

2-2 D-SUB SIGNAL CABLE SPECIFICATION
* VGA/SVGA SIGNAL CABLE PIN CONNECTION (15 PIN D-SUB MINIATURE SIGNAL
CONNECTOR WITH CABLE ; PCB CKT NO.: CN404 )
CONNECTION
REMARK
D-SUB 15PIN IBM PC WIRE COLOR 6P CONN 6P CONN
1 RED RED COAX-IN 6P CONN-6
2 GREEN GREEN COAX-IN 6P CONN-5
3 BLUE BLUE COAX-IN 6P CONN-4
4 N.C - -
5 GND BLACK 6P CONN-3
6 RED-GND -
7 GREEN-GND - RING WIRE
8 BLUE-GND -
9 N.C - -
10 ID - -
11 N.C - -
12 SDA - -
13 H-SYNC (C/S) ORANGE 6P CONN-1
14 V-SYNC WHITE 6P CONN-2
15 SCL - -
SHELL GND - RING WIRE
*CGA / EGA 6PIN CONNECTION ( PCB CKT NO. : CN406 )
CONNECTION
REMARK
CGA SLOT ZAMMA Spec_ WIRE COLOR 6P CONN (@ PCB)
1 , A H-SYNC WHITE 6P CONN-6
16 V-SYNC YELLOW 6P CONN-5
28 , f GND & SHELL BLACK 6P CONN-4
T BLUE BLUE 6P CONN-3
17 GREEN GREEN 6P CONN-2
U RED RED 6P CONN-1
*CGA / EGA 5PIN CONNECTION ( PCB CKT NO. : CN409 )
CONNECTION
REMARK
CGA SLOT ZAMMA Spec_ WIRE COLOR 5P CONN (@ PCB)
1 , A H/V COPOSITE-SYNC WHITE 5P CONN-5
28 , f GND & SHELL BLACK 5P CONN-4
T BLUE BLUE 5P CONN-3
17 GREEN GREEN 5P CONN-2
U RED RED 5P CONN-1
-7-

2-3 TIMING CHART
HORIZONTAL VERTICAL
VIDEO
C D E Q R S
SYNC
B P
A O
A : LINE TIME TOTAL B :HORIZONTAL SYNC WIDTH

C : BACK PORCH D : ACTIVE TIME
E : FRONT PORCH
O : FRAME TIME TOTAL P : VERTICAL SYNC WIDTH

Q : BACK PORCH R : ACTIVE TIME
S : FRONT PORCH
CGA EGA VGA SVGA

DESCRPTION
640 x 200 640 x 200 640 x 400 640*480 800*600
f KHz 15.750 15.750 24.827 31.469 37.88
A uS 63.5 63.5 40.28 31.778 26.40
B uS 8.671 8.672 3.04 3.813 3.20

H
C uS 7.272 7.272 3.8 1.907 2.20
D uS 40.836 40.836 30.399 25.422 20.00

E uS 6.72 6.72 3.04 0.636 1.00
POL. POS POS POS NEG POS
f Hz 50 60.115 55.609 59.940 60.317
O mS 20.0 16.63 17.98 16.683 16.58
P mS 0.444 0.444 0.322 0.064 0.11
V Q mS 0.825 0.825 1.26 1.048 0.61
R mS 18.603 15.302 16.111 15.253 15.84
S mS 0.128 0.06 0.282 0.318 0.03

POL. POS POS POS NEG POS
-8-

3. Operating Instruction
3-1 SET ASS'Y
3.2 MAIN PCB ASS'Y
-9-

3-3. Function of Control
UP
DOWN
MENU (SELECT)
EXIT (DEGAUSSING)
LED
Control Function
The light of power LED changes according to each state.
LED
◎ on mode : Green LED.
(Power Indicator)
◎ power saving mode : green LED blinking.
When you press this button, the MENU appears.The MENU will
disappear in 10 seconds if you don't operate any button.
When you press EXIT button again, the MENU disappears.
MENU(Sellect)
This button is used to select the control item on the MENU.
In MENU, the control item could be selected and unselected by
this button.
EXIT This button is used to exit the value of any selected control.
This button is used to increase the value of any selected control.
UP
This button is used to locate to the next control item for select.
This button is used to decrease the value of any selected control.
DOWN This button is used to locate to the previous control item for
select.
- 10 -

4.Adjustments
4-1. Adjustment Control

4-1-1. Before making Adjustments
1) Orientation
When servicing, always face the monitor to east.
2) Warm-up time
The monitor must be on for 30 minutes before starting alignment. Warm-up
time is especially critical in color temperature and white balance
adjustments.
3) Signal
Analog, 0.714Vp-p positive at 75Ω, internal termination.
4) High Voltage Adjustment
Signal : without signal
Adjustment : 26KV ± 0.3KV.
PROCEDURE
① Disconnect the AC line cord from the power source.
② Connect positive end of High Voltage probe to anode cap of CRT, negative
end of to GND(main chassis)
③ First of all Disconnect AC cord and than disconnect High voltage probe.
5) Screen Voltage
- signal : 640 * 480 (60Hz) , Full white
- Bright : max
- Contrast : max
- Adjustment (SAMSUNG SDI) : 550 ±10V
4-1-2 TURN ON THE FACTORY OSD MANUAL METHOD

1) press on the "UP" key.
2) connect the AC line cord from the power source.
3) At this time OSD menu changed factory mode.
◑
HV AC OSD OSD VF i
BRIGHTNESS
31.4KHz
60Hz
- 11 -

4-2. Display Control Adjustment
Click on the "MENU" button (OSD MENU).
This menu is user's OSD manual.(user's manual)
BRIGHTNESS
31.4KHz 60Hz
1) Click on the "MENU" button.

2) Click on the "UP"or "DOWN" and move any function control.
3) Press the "MENU(SELECT)" button.
4) "UP" or "DOWN" button is used to control the value of any function.
5) When you press exit button, the MENU disappears.
4-2-1 Screen center adjustment

width : 520mm height : 400mm
signal : 640 * 480 (60Hz)
｜A-B｜≤ 4.0mm , ｜C-D｜≤ 4.0mm
C
DISPLAY AREA
SQUARE CORNER
A B
a) Horizontal size adjustment

adjustment : use to "H-SIZE", 520±3mm
- 12 -

b) Vertical size adjustment
adjustment : use to "V-SIZE", 400±3mm
c) Horizontal position adjustment
adjustment : use to "H-POS"
d) Vertical position adjustment
4-2-2 Trapezoid adjustment
frequency : all mode
signal pattern : cross hatch
A A
B B
｜A-B｜< 2.5mm
4-2-3 Pin balance adjustment

｜D1｜,｜D2｜≤1mm
D1 D2 D1
4-2-4 Parallelogram adjustment

5mm
- 13 -

4-2-5 Side pin-cushion adjustment C2
brightness : MIN (cut-off) D1 D2
contrast : MAX
C1
｜C1｜,｜C2｜≤2.0mm, ｜D1｜,｜D2｜≤2.0mm
4-2-6 Tilt adjustment

brightness : MIN (cut-off)
contrast : MAX
4-2-7 Degaussing adjustment

Don't adjust the degaussing. Degaussing is possible in OSD
adjustment menu. After using this function once, You must
use again after at least 30minutes.
4-2-8 SAVE ADJUSTMENT CONDITION & REMOVE USER MODE.
- 14 -

4-3 Color adjustment
4-3-1 color temperature
※ Set condition
- measuring instrument : color analyzer (CA-100)
- frequency : 640 * 480 (60Hz)
- display pattern : full white , one square(20% window)
- brightness : cut off
- contrast : MAX
※ specification
- 9300K x=0.281±0.02 , y=0.311±0.02
- 6500K x=0.313±0.02 , y=0.329±0.02
4-3-2 color adjustment (9300K)

a) Back raster color adjustment
※ Set condition
- frequency : 640 * 480 (60Hz)
- display pattern : back raster pattern
- brightness : MIN (cut off)
- contrast : MAX
1. Select factory mode.

2. Select COLOR TEMP with UP.DOWN key.
3. Select 9300K.
4. Adjust back raster brightness to 0.01~0.02(F/L) with VR601.
5. Select B-B with UP,DOWN adjust y=0.311 and do the next
selection with EXIT key.
6. Select R-B with UP,DOWN adjust x=0.281 and do the next
a) white balance / ACL adjustment

※ Set condition
- frequency : 640 * 480 (60Hz)
- display pattern : one square(20% window) , full white
- contrast : MAX
- 15 -

2. Select COLOR TEMP with UP,DOWN key.
3. Select 9300K.
4. Select B-G with UP,DOWN adjust y=0.311 and do the next
6. Select R-G with UP,DOWN adjust x=0.281 and do the next
7. Select contrast icon with UP,DOWN key, adjust contrast to
50~60f/l with UP,DOWN key.
front cabinet
20% window pattern
back raster
8. Select ACL key(A/C) in full white pattern and adjust ACL to

28~30f/l.
front cabinet
full white
back raster
※ attention : If 50f/l doesn't adjust in 20% window, adjust G-G

again with DOWN key.
4-3-3 color adjustment (6500K)

a) white balance adjustment
2. Select COLOR TEMP with UP,DOWN key.
3. Select 6500K.
- 16 -

4. Select B-G with UP,DOWN adjust y=0.329 and do the next
6. Select R-G with UP,DOWN adjust x=0.313 and do the next
4-3-4 brightness uniformity adjustment

※ set condition
- frequency : 640 * 480 (60Hz)
- display pattern : 9 ball pattern
- contrast : MAX
Measure nine brightness display in the screen.
front cabinet
4-3-5 Focus adjustment

※ set condition
- frequency : 640 * 480 (60Hz)
- display pattern : "H" character
- brightness : min (cut off)
- contrast : max
1. Adjust in focus of whole screen to be the best fitted with
FOCUS V/R in FBT.
4-3-6 PURITY adjustment

Purity is that unnecessary colors appear in the screen except
displayed color. Don't appear unnecessary colors divided with
the naked eye at a distance of 50㎝ from CRT surface.
- 17 -

※ set condition
- direction : east
- frequency : included timing chart
- display pattern : full white
- brightness : MIN (cut off) - display center
Most suitable
RED x=0.640 ± 0.015 y=0.323 ± 0.015
GREEN x=0.295 ± 0.015 y=0.594 ± 0.015
BLUE x=0.142 ± 0.015 y=0.066 ± 0.015
- 18 -

5. TROUBLESHOOTING GUIDE
5-1. Troubleshooting Guide.

NOTES ;
1. If picture does not appear, fully rotate the brightness and contrast controls
clockwise.
2. Check the following circuits.
No raster appear : power circuit. Horizontal output circuit.
High voltage control circuit and output circuit.
High voltage develops but no raster appears : Video output circuit.
High voltage does not develop : Horizontal output circuit.
5-2-1. No Raster, No Video
No Power
Measure +80V output between

Check the other secondary
cathode of D110 and Ground. YES
outputs(+250V,+130V,+80V,+12V,
Does appear 80V DC?
-12V,+12V,+6.3V ,5V Lines)
NO Does each output appear?
Check and replace Check and replace

Check Video and
F101,IC103 D104,D105,D106
Horizontal circuits
D108,IC103,IC101
5-2-2 S-Correction failure. C/S TABLE

S1 S2 S3
1 ~17K L L L
Check S1,S2,S3 signals refer to 2 17~28K L L H

IC103 1pin
S-correction table on the schematic 3 29~34K L H H
4 34~40K H H H
S1,S2,S3 signal are right NO

at each frequency block Check and replace
YES
Check and replace

Q704,707,709,703,706,708
- 19 -

5-2-3 Degaussing failure
Check degauss
Connector(CN102)
YES
Check output voltage at pin 12 of IC502

NO
(Normal : 0V, Degaussing: 5V) Replace IC502
Does DC voltage right?
YES
Check and replace

Q101,D101,RL101,R101
5-2-3 Purity failure
Degaussing
YES
Purity is O.K Done
NO
Degaussing circuit NO
Refer to 5-2-2
is right?
YES
Replace CRT and

verify purity
- 20 -

5-2-4 Rotation Failure
Check tilt connection

(CN402)
IC 502 pin 35 output varies

with different values? NO
Check and replace IC502
(DC 0V～5V)
YES
Q403,Q401,Q402 NO Check and replace

varies with different values? Q403,Q401,Q402
YES
Check and replace

R-COIL of the CPT
5-2-5 Misconvergence Failure
Try readjusting convergence
NO
Is the convergence YES

now within spec? Done
NO
YES
Readjusting convergence Done
NO
Is the convergence
now within spec?
NO
Change CPT and

readjusting convergence
- 21 -

5-2-6 H-Linearity Failure
Check pin 36 of IC502 output

NO
varies with different value? Check and replace IC502
(DC 0V～5V)
YES
Check Q702,Q701 output

NO
varies with different value? Check and replace
Q702,Q701
YES
Check L304 output

varies with different value?
L304
5-2-7 High Voltage Failure
Does 900Vp-p fly back pulse NO Check and replace

appear on pin 1 of FBT? Q704,D708,R716
YES
NO
Q602,606 base driving pulse exist? Check +12V,Q602,606
YES
NO
Q603 drain pulse exist? Check and replace Q603
YES
NO
Q603 gate pulse exist? Check and replace D608,610
YES
NO
Pin 9 of IC602 pulse exist? Replace IC602
Q602,Q606 BASE FBT 1pin

- 22 -

5-2-8 User control Failure
Others
Check the voltage at pin 21

of IC502 Normal : 5V
Push the EXIT Key : 0.5V
Push the SEL Key : 1.5V
Push the UP Key : 3.5V
Push the DOWN Key : 2.5V
NO
Check and replace

R406,R408,R409,R410
5-2-10 Dynamic Focus Failure or poor Focus
YES
Try Readjusting double Focus Done
NO
Check the wave form at SG601

NO Check and replace
Collector.Does appear parabola
R712,T701
wave form?

T701 wave form is right?
T701
YES
Replace the CPT

and verify focus
T701
- 23 -

5-2-10 Visible Retrace
NO Check Screen control voltage

Is Screen voltage (550±50V) right?
and FBT
YES
Does Q201 collector pulse NO

Check 80V Line
(35Vp-p) exist?
YES
Does Q201 base drive NO

Check The G1
wave form exist?
YES
Q201 COLLECTOR G1
5-2-11 ACL Failure
Input full white pattern to monitor

YES
Check the voltage at pin 2 of IC502? NO

Check replace IC502
(PWM WAVE FORM)
YES
NO
Q605,Q607 base input exists? Check replace
YES Q605, 12V
Check and replace pin

12 of the IC802?
IC502 2pin PWM
- 24 -

5-2-12 Micom Failure
Does 5V appear Pin6 of IC502?
YES
X501
IC502 Pin8 and pin8 wave NO Check and replace
form are right? X501,C512,C513
YES
IC502 Pin 5 is over than NO

Check and replace R507
4.5Volt ?
YES
All input/output value NO

are right?
YES
Done
5-2-13 No Raster
Does fly back pulse at NO Check D712,D715

collector of Q712 appear? and 80V Line
YES IC301 26pin
Check the Pin 26 of IC301.Does NO

12Vp-p pulse appear?
YES
Does the wave form at

pin 8 of T703 appear?
Q714,Q715,Q713
YES
T703 8pin
Check the voltage PIN 7 of NO Check the
IC701 Does 12V DC appear? 12V line
YES
Does the wave form at NO Check and replace

pin 4 of IC701 appear? IC701
YES
Check heater
voltage 6.3V
- 25 -

5-2-14 No Video
Check signal cable

and connector
YES
IC802 Pin5,Pin8,Pin10 video NO Check R,G,B Cable

input are right? conector
YES
IC802 Pin21,Pin24,Pin26 NO Check and replace

video output are right? IC802
YES
Q802R,G,B NO Check Q803 and

video output are right? 12V,80V Line
YES
R,G,B cathode wave NO Check R806R,G,B and

forms are right? Q801R,G,B
YES
G2 voltage are right? NO Check screen,CPT

(550±50V) socket, and FBT
YES
G1 voltage are right?

(-45 ±10V)
YES
Check and replace CPT
R,G,B Cathode wave form
- 26 -

5-2-15 Abnormal & Invariable H-size
IC 301 Pin24 output NO Check and replace IC301

parabola level variable? and 12V,80V Line?
YES
Does T303 Pin8 pulse NO

Check and replace T303?
is appear??
YES
Check some parts around

T702 are they OK?
YES
Check and replace

Q710?
IC301 24pin
5-2-16 OSD failure
Check CN401
YES
IC801 Pin5, Pin10 wave NO Check and replace

forms are right? Q801,Q802
YES
When you click on the V-FLY

"MENU" botton. IC801 NO Check and replace
Pin13,Pin14,Pin15,Pin12 IC801,5V Line
wave forms are right?
YES
When you click on the

"MENU" botton. IC502 NO Check IC502 and
Pin10,Pin11, wave forms SDA,SCL Line
are right?
YES
H-FLY
- 27 -

5-2-17 V-deflection failure
Does 12V DC appear at

Pin2 of IC201? NO
Refer to No power supply
Does -12V DC appear at
Pin5 of IC201?
YES
IC 301 Pin 13,Pin 23 NO

Check and replace IC301?
output exist?
YES
IC 502 Pin 33 output NO

exist?
YES
IC201 5 pin IC201 1 pin
- 28 -

6. PART LIST
6-1. KT-1982F PART PIST
1 02-291411010 KT-2914F,KORTEK MAIN PCB ASS'Y 1 MAIN MANUAL
1 09-131530P20 19N20 FET 1 PCS Q708
1 09-131530P21 11N40 FET 1 PCS Q710
1 11-6S1265RHA FS6S1265-YDTU IC-POWER 1 EA IC103
1 11-KA358AXAA KA358A IC-OPAMP 1 EA IC601
1 11-KA3883CAA KA3883C IC-PWM 1 EA IC701
1 11-KA431AZGA KA431AZ IC-SCR 1 EA C102
1 11-KA7500BAA KA7500B IC-PWM 1 EA IC602
1 11-KA7805XEA KA7805 IC-REGULATOR 1 EA IC106
1 11-KA78R12FA KA78R12 IC-REGULATOR 1 EA IC103
1 11-KS24C04AA S524C80D41-DCB0 IC-I2C 1 EA IC501
1 11-LTV817BAA LTV817-B IC-PHOTO COUPLER 1 EA IC101
1 11-S74HC86AA HD74HC86D/TC74HC86AP IC 1 EA IC503
1 11-STV6888AA STV6888 (TDA9116) IC-TIMEBASE 1 EA IC301
1 11-TDA8172CA TDA8172 IC 1 EA IC201
1 11-WT6291XAA WT62P1 IC-MCU 1 EA IC502
1 21-1001R5J8A 1/2W 1.5 OHM RES. CARBON 1 EA R210
1 21-1006R8J5A 1/4W 6.8 OHM RES. CARBON 1 EA R618
1 21-100R47J8A 1/2W 0.47OHM RES. CARBON 1 EA R206
1 21-101000J5A 1/4W 10 OHM RES. CARBON 1 EA R402
1 21-120100J5A 1/4W 1 KOHM RES. CARBON 1 EA R702
1 21-1201R8F4A 1/6W 1.8 KOHM1% RES. METAL 1 EA R107
1 21-1201R8J5A 1/4W 1.8 KOHM RES. CARBON 1 EA R525
1 21-131000F5A 1/4W 10 KOHM1% RES. METAL 1 EA R632
1 21-150100J8A 1/2W 1 MOHM RES. CARBON 1 EA R623
1 21-300100JBB 1W 1 OHM RES. MOR 1 EA R113
1 21-300100JCB 2W 1 OHM RES. MOR 1 EA R738
1 21-3001R2JEF 3W 1.2 OHM RES. MOR 1 EA R748
1 21-300R33JBB 1W 0.33 OHM RES. MOR 1 EA R619
1 21-304700JEF 3W 47 OHM RES. MOR 1 EA R701
1 21-3206R8JEF 3W 6.8 KOHM RES. MOR 1 EA R118
1 21-341800FBB 1W 180 KOHM1% RES. MOR 1 EA R102
1 21-800100J8A 1/2W 1 OHM RES. FUSEBLE 1 EA R732
1 22-630V410NT 630VT 100 KOHM T/P RES.VARIABLE 1 EA VR601
1 23-109C0224T 63V 224K T/P (DW,OY) MP 1 EA C733
1 23-10FA0104T 250V 104K T/P MP 1 EA C604
- 29 -

1 23-24B70103B DTN 100V 103H CAP. METAL 1 EA C735
1 23-27B70102B P.P,YPN 100V 102G CAP. METAL 1 EA C305
1 23-27B70472B P.P,YPN 100V 472G CAP. METAL 1 EA C613
1 23-32F90154B DTM,YMPP 250V 154J CAP. METAL 1 EA C702
1 23-33R90102B DTMS,YPN 1.6KV 102J CAP. METAL 1 EA C612
1 23-34F90103B DTN,YPN 250V 103J CAP. METAL 1 EA C706
1 23-70B90153T 100V 153J T/P(DI,OY) CAP. MYLAR 1 EA C102
1 23-70B90154T 100V 154J T/P CAP. MYLAR 1 EA C309
1 26-81590121T DC50V-SL-121UF(J)T/P CAP. CERAMIC 1 EA C313
1 26-81590221T DC50V-SL-221PF(J)T/P CAP. CERAMIC 1 EA C514
1 26-81590331T DC50V-SL-331PF(J)T/P CAP. CERAMIC 1 EA C734
1 26-820A0102T DC50V-B-102PF(K) T/P CAP. CERAMIC 1 EA C506
1 26-822R0103T DC50V-F-103PF(Z) T/P CAP. CERAMIC 1 EA C736
1 26-P20A0101T DC1KV-B-101PF(K) T/P CAP. CERAMIC 1 EA C716
1 26-R20A0102T DC2KV-B-102PF(K) T/P CAP. CERAMIC 1 EA C714
1 27-1404022JT SMG 400V 220 UF CAP. ELECT. 25*40 1 EA C114
1 27-1603010FB SMS 250V 10 UF CAP. ELECT. 1 EA C615
1 27-16030228T SMS 50V 22 UFT/P CAP. ELECT. 1 EA C603
1 27-1603047DB SMS 160V 47 UF CAP. ELECT. 1 EA C101
1 27-16040228T SMS 50V 220 UFT/P CAP. ELECT. 1 EA C206
1 30-1B3906TAX 2N3906-TA TR. 1 EA Q606
1 30-1P1271TAX KTA1271-Y TR. 1 EA Q402
1 30-2Z0033TAX KSP92 TR. 1 EA Q601
1 30-3M1008TAX KSC1008-Y TR. 1 EA Q101
1 30-3Q3198TAX KTC3198-Y TR. 1 EA Q702
1 30-4F5584BNX 2SC5584 TR. 1 EA Q712
1 30-8Z0008BDX FQP4N20 FET 1 EA Q713
1 30-8Z0027BEX SSS10N60A FET 1 EA Q603
1 31-100002MZX ATS-49/U 12MHZ CRISTAL 1 EA X501
1 33-130001901 FQM19A002 F.B.T 1 EA T601
1 33-210082004 SCT-82D (경인,삼흥) TRANS.SCAN KT-2938F 1 EA T303
1 33-260082001 HDT-82 (경인,삼흥) TRANS.DRIVE KT-1982 1 EA T703
1 33-312932001 60T (경인,삼흥) TRANS.SYNC KT-2932 1 EA T103
1 33-340082002 GTT-82 (경인,삼흥) TRANS.GATE KT-1982 1 EA T702
1 33-360014001 DFT-14 (경인,삼흥) TRANS,FOCUS KT-2914 1 EA T701
1 34-160040001 LF-40 (경인,삼흥) LINE FILTER KT-2938F 1 EA T102
1 34-180001002 10UH (경인,삼흥) LINEARITY KT2914F 1 EA L304
1 34-22031510X AL03 TB151K (150UH) INDUCTORS 1 EA L301
1 34-22034700X AL03 TB470K (47UH) INDUCTORS 1 EA L602
1 34-250014000 SPT-14 (경인,삼흥) TRANS,SMPS 1 EA T101
1 35-A1N40072T 1N4007GP DIODE 1 EA D702
1 35-CGBU6JL1B GBU6JL DIODE 1 EA D120
1 35-F1N52422T 1N 5242 1/2W 12V DIODE ZENER 1 EA D102
1 35-HDTV56F1B DTV 56F DIODE 1 EA D309
1 38-1013A1025 8D-13 THERMISTOR-NTC 1 EA TH102
1 38-2009A2024 2PIN-9OHM THERMISTOR-PTC 1 EA TH101
1 38-4152A1021 1.5KV SPARK GAP 1 EA SG601
1 39-313310000 KT-2914 MAIN PCB 247*247 1 EA MAIN PCB
1 41-HRCR71200 HR-CR7DC12V(HAN KUK)RELAY (KT-XX82) 1 EA RL101
1 44-180101800 15P*1800mm KORTEK SIGNAL KT-2914 1 EA SIGNAL CABLE
1 48-050405000 4P 500mm S/W 일반 CONNECTOR KT-XX82 1 EA CN401
1 48-051303500 13P*13P*350mm CONNECTOR KT-**82 1 EA CN411
1 49-0526702XX 5267-02 WAFER 1 EA CN402
1 49-0526706XX 5267-06 WAFER 1 EA CN404
1 49-0LW064005 LW 0640-05 WAFER LPH01-05 1 EA CN409
1 49-0LW114306 LW 1143-06 WAFER LPHP03-06 1 EA CN406
1 49-2IS42PXXX 42 PIN IC SOCKET 1 EA IC502
1 50-21X215BDA 215 250V 3.15A FUSE 1 EA F101
1 52-700001XXX 1 PIN (2.36) PIN BASE 1 EA CN410
1 52-700006XXX YFW 800-02 8 m/m PIN BASE 1 EA CN102
1 52-700007XXX YFW 800-02 10m/m PIN BASE (YEON HO) 1 EA CN103
1 52-700008XXX YFW 800-04 PIN BASE (YEON HO) 1 EA CN701
1 21-100100J8A 1/2W 1 OHM RES. CARBON 2 EA R207,R301
1 21-1001R2F8A 1/2W 1.2 OHM 1% RES. METAL 2 EA R215,R216
- 30 -

1 21-1004R7J5A 1/4W 4.7 OHM RES. CARBON 2 EA R116,R746
1 21-1205R1J4A 1/6W 5.1 KOHM RES. CARBON 2 EA R609,R630
1 21-131000F4A 1/6W 10 KOHM1% RES. METAL 2 EA R211,R309
1 21-131200F4A 1/6W 12 KOHM1% RES. METAL 2 EA R605,R727
1 21-132200J4A 1/6W 22 KOHM RES. CARBON 2 EA R201,R631
1 21-802200J8A 1/2W 22 OHM RES. FUSEBLE 2 EA R733,R752
1 23-33R90472B DTMS,YPN 1.6KV 472J CAP. METAL 2 EA C727,C728
1 23-39G90224X BOX AC 275V 224UF CAP. BOX(PILKOR) 2 EA C111,C120
1 23-70B90222T 100V 222J T/P CAP. MYLAR 2 EA C131,C737
1 26-81590022T DC50V-SL-22PF(J) T/P CAP. CERAMIC 2 EA C512,C513
1 26-81590101T DC50V-SL-101PF(J)T/P CAP. CERAMIC 2 EA C507,C516
1 26-81590681T DC50V-SL-681PF(J)T/P CAP. CERAMIC 2 EA C515,C726
1 27-10050103B SR 16V 1000 UF CAP. ELECT. 12.5*16 2 EA C112,C113
1 27-1203047HB SHL 350V 47 UF CAP. ELECT. 16*25 2 EA C130,C711
1 27-1204010BB SHL 100V 100 UF CAP. ELECT. 10*20 2 EA C126,C602
1 27-16030473T SMS 16V 47 UFT/P CAP. ELECT. 5*11 2 EA C508,C607
1 30-1J0733TAX KSA733C-Y TR. 2 EA Q711,Q715
1 30-8Z0007BDX FQP19N20 FET 2 EA Q703,Q706
1 35-ABAV21X2T BAV21 DIODE 2 EA D605,D704
1 35-BMUR4601T GUR460 DIODE 2 EA D608,D610
1 35-BUF1GXX1T UF-1G DIODE 2 EA D108,D707
1 35-BUF54042T UF5404GI DIODE 2 EA D105,D106
1 35-F1N52302T 1N 5230 1/2W 4.7V DIODE ZENER 2 EA D103,D601
1 35-F1N52322T 1N 5232 1/2W 5.6V DIODE ZENER 2 EA D403,D404
1 49-0SMW25006 SMW 250-06 WAFER 2 EA CN405,CN407
1 52-300002XXX FC-51F KT-1970/1982 FUSE CLIP TAPING 2 EA F101
1 21-111200J4A 1/6W 120 OHM RES. CARBON 3 EA R801,R816,R817
1 21-1201R5J4A 1/6W 1.5 KOHM RES. CARBON 3 EA R109,R611,R703
1 21-1208R2J4A 1/6W 8.2 KOHM RES. CARBON 3 EA R205,R401,R705
1 21-141000J4A 1/6W 100 KOHM RES. CARBON 3 EA R709,R718,R724
1 21-331000JEF 3W 10 KOHM RES. MOR 3 EA R626,R627,R712
1 23-70B90473T 100V 473J T/P CAP. MYLAR 3 EA C712,C725,C502
1 26-F21C0222B DS250V-E-222PF(M) CAP. CERAMIC 3 EA C109,C110,C129
1 26-M20A0102T DC500V-B-102PF(K)T/P CAP. CERAMIC 3 EA C707,C713,C731
1 26-M22R0103T DC500V-F-103PF(Z)T/P CAP. CERAMIC 3 EA C103,C116,C715
1 26-R20A0221T DC2KV-B-221PF(K) T/P CAP. CERAMIC 3 EA C121,C610,C704
1 27-16030338T SMS 50V 33 UFT/P CAP. ELECT. 5*11 3 EA C123,C617,C724
1 27-16040223T SMS 16V 220 UFT/P CAP. ELECT. 8*11.5 3 EA C138,C614,C730
1 27-41023R38T SMBP 50V 3.3 UF T/P CAP. ELECT. 5*11 3 EA C307,C620,C622
1 30-3Q3203TAX KTC3203-Y TR. 3 EA Q401,Q403,Q701
1 21-1202R2J4A 1/6W 2.2 KOHM RES. CARBON 4 EA R513,R530,R602,R607
1 21-134700J4A 1/6W 47 KOHM RES. CARBON 4 EA R533,R536,R729,R214
1 23-109A0474T 63V 474K T/P (DW,OY) MP 4 EA C308,C311,C718,C720
1 23-70B90103T 100V 103J T/P(DI,OY) CAP. MYLAR 4 EA C105,C107,C303,C719
1 30-3B3904TAX 2N3904-TA TR. 4 EA Q602,Q604,Q605,Q607
1 35-B31GF6X1B 31GF6 DIODE 4 EA D110,D112,D113,D121
1 21-131800J4A 1/6W 18 KOHM RES. CARBON 5 EA R706,R716,R721,R739,R751
1 26-81590033T DC50V-SL-33PF(J) T/P CAP. CERAMIC 5 EA C403,C404,C405,C504,C505
1 27-16024R78T SMS 50V 4.7 UFT/P CAP. ELECT. 5*11 5 EA C209,C302,C312,C401,C621
1 27-16030108T SMS 50V 10 UFT/P CAP. ELECT. 5*11 5 EA C501,C503,C509,C601,C721
1 35-BUF40072T UF4007GI DIODE 5 EA D107,D111,D614,D615,D616
1 21-1206R8J4A 1/6W 6.8 KOHM RES. CARBON 6 EA R106,R213,R308,R621,R737,R747
1 21-131000J4A 1/6W 10 KOHM RES. CARBON 6 EA R103,R305,R503,R506,R620,D301
1 23-70B90104T 100V 104J T/P(DI,OY) CAP. MYLAR 6 EA C127,C128,C301,C402,C517,C619
1 26-822R0104T DC50V-F-104PF(Z) T/P CAP. CERAMIC 6 EA C122,C204,C406,C606,C616,C732
1 27-12040473T SHL 16V 470 UFT/P CAP. ELECT. 8*11.5 6 EA C118,C119,C135,C203,C205,C304
1 30-3M0945TAX KSC945C-Y TR. 6 EA Q103,Q201,Q704,Q707,Q709,Q714
- 31 -

1 21-1201R2J4A 1/6W 1.2 KOHM RES. CARBON 7 EA R306,R708,R710,R717,R719,R723,R725
1 35-BUF40041T UF4004GI DIODE 7 EA D104,D109,D202,D612,D703,D711,D715
1 27-16020018T SMS 50V 1 UFT/P CAP. ELECT. 5*11 8 EA C125,C201,C310,C608,C618,C701,C708,C723
R104,R505,R514,R515,R537,R608,R613,R616,
1 21-120100J4A 1/6W 1 KOHM RES. CARBON 10 EA
R622,R624
L101,L103,L104,L105,L107,L601,L604,L605,L7
1 34-413550001 ATS3550L(3.5X5mm) BEAD CORE 12 EA
02,L703,L704,L705
R129,R204,R208,R501,R502,R504,R508,R509,
1 21-1204R7J4A 1/6W 4.7 KOHM RES. CARBON 14 EA
R510,R511,R512,R519,R603,R628
R303,R304,R411-R413,R417-R419,R521-R524,
1 21-111000J4A 1/6W 100 OHM RES. CARBON 18 EA
R526,R529,R531,R534,R535,R744
D101,D114,D115,D401,D602-D604,D606,D607,D611,D613,D6
1 35-E1N41482T 1N 4148 DIODE 19 EA
17,D701,D705,D706,D708-D710,D714
1 43-880052R0T 52 mm TAPING JUMP WIRE ## EA R131,D116,J001~J128
2 05-112914010 KT-2914F,KORTEK V-MANUAL ASS'Y 1 PCS CRT SOCKET PCB
2 11-KA2506XAA KA2506 IC-PREAMP 1 EA IC802
2 11-WT6802XAA WT6802 IC-OSD 1 EA IC801
2 26-R20A0102T DC2KV-B-102PF(K) T/P CAP. CERAMIC 1 EA C816
2 27-16023R38T SMS 50V 3.3 UFT/P CAP. ELECT. 5*11 1 EA C834
2 27-1603010DT SMS 160V 10 UFT/P CAP. ELECT. 10*16 1 EA C804
2 27-16040103T SMS 16V 100 UFT/P CAP. ELECT. 6.3*11 1 EA C801
2 38-3400M1021 WSP 401M SURGE ABSORBER 1 EA SG803
2 38-4152A1021 1.5KV SPARK GAP 1 EA SG802
2 39-111820000 KT-2914 VIDEO PCB 1 EA VIDEO PCB
2 48-040603304 6P*6P*380mm RGB CONNECTOR,KT-2914 1 EA CONNECTOR,KT-2914
2 49-0SMW25013 SMW 250-13 WAFER 1 EA CN801
CRT SOCKET
2 49-162601XXX PCS 626-01 1 EA CRT801
KT-XX03V
2 52-700001XXX 1 PIN (2.36) PIN BASE 1 EA CN803
2 52-700006XXX YFW 800-02 8 m/m PIN BASE 1 EA CN806
2 26-81090101T DC50V-CH-101PF(J)T/P CAP. CERAMIC 2 EA C806,C807
2 27-16040223T SMS 16V 220 UFT/P CAP. ELECT. 8*11.5 2 EA C810,C823
2 30-3B3904TAX 2N3904-TA TR. 2 EA Q801,Q802
2 09-121540P20 C3503-D H/S ASS'Y 3 PCS Q803R,Q803G,Q803B
2 21-111000J8A 1/2W 100 OHM RES. CARBON 3 EA R806R,R806G,R806B
2 21-112200J4A 1/6W 220 OHM RES. CARBON 3 EA R808R,R808G,R808B
2 21-120100J4A 1/6W 1 KOHM RES. CARBON 3 EA R802,R805,R806
2 21-1203R3J4A 1/6W 3.3 KOHM RES. CARBON 3 EA R811R,R811G,R811B
2 21-1204R7J4A 1/6W 4.7 KOHM RES. CARBON 3 EA R804R,R804G,R804B
2 21-135600J4A 1/6W 56 KOHM RES. CARBON 3 EA R809R,R809G,R809B
2 21-9201R5FJW 7W 1.5 KOHM 1% RES. CEMENT 3 EA R801R,R801G,R801B
2 23-70B90104T 100V 104J T/P(DI,OY) CAP. MYLAR 3 EA C802R,C802G,C802B
2 26-81090010T DC50V-CH-10D(J) T/P CAP. CERAMIC 3 EA C803R,C803G,C803B
2 26-81590033T DC50V-SL-33PF(J) T/P CAP. CERAMIC 3 EA C805R,C805G,C805B
2 27-4102001BT SMBP 100V 1 UF T/P CAP. ELECT. 5*11 3 EA C801R,C801G,C801B
2 30-3Z0030TAX KSP2222A TR. 3 EA Q805R,Q805G,Q805B
2 34-22031R20X AL03 TB1R2K (1.2UH) INDUCTORS 3 EA L801R,L801G,L801B
2 35-ABAV21X2T BAV21 DIODE 3 EA D805R,D805G,D805B
2 35-F1N52402T 1N 5240 1/2W 10V DIODE ZENER 3 EA D804R,D804G,D804B
2 38-3200M1021 WSA 201M SUREG ABSORBER 3 EA SG801R,SG801G,SG801B
2 35-E1N49371T 1N 4937 DIODE 4 EA D801R,D801G,D801B,D812
2 26-M22R0103T DC500V-F-103PF(Z)T/P CAP. CERAMIC 5 EA C804R,C804G,C804B,C809,C820
2 21-106800J5A 1/4W 68 OHM RES. CARBON 6 EA R813R,R813G,R813B,R814R,R814G,R814B
2 30-2Z0033TAX KSP92 TR. 6 EA Q802R,Q802G,Q802B,Q804R,Q804G,Q804B
2 30-3Z0032TAX KSP44TA TR. 6 EA Q801R,Q801G,Q801B,Q806R,Q806G,Q806B
2 21-113900J4A 1/6W 390 OHM RES. CARBON 7 EA R804,R807,R809,R813,R827,R828,R829
2 34-413550001 ATS3550L(3.5X5mm) BEAD CORE 7 EA L801,L802,L805,L806,L807,L808,L809
2 26-822R0104T DC50V-F-104PF(Z) T/P CAP. CERAMIC 8 EA C803,C812,C813,C814,C815,C817,C819,C822
R805R,R805G,R805B,R807R,R807G,R807B,R82
2,R825,R826
D803,D803R,D803G,D803B,D806,D807,D808,D
2 35-E1N41482T 1N 4148 DIODE 10 EA
809,D810,D811
R810,R811,R814,R819,R821,R824,R832,R833,
R834,R835,R836
2 43-880052R0T 52 mm TAPING JUMP WIRE 33 EA J801~J833
- 32 -

3 07-122914100 KT-2914,KORTEK S-MANUAL TACT ASS'Y 1 PCS TACT SW PCB
3 37-110002GRA DLL-30631,GREEN 3PI LED,KT-XX82 1 EA D402
3 49-0526804XX 5268-04 WAFER 1 EA CN403
3 58-311105002 RT1105TA TAPING SWITCH TACT 1970 4 EA SW401.SW402.SW403.SW404
6-2. DIFFERENT PART LIST BY MODEL

MODEL
NOCKT. NO
KT-2914F KT-2914DF KT-2914DF KT-2114DF KT-2114F
1 CRT SDI SDI LGP ORION SDI
2 C727 472,1.6KV MPP 332,1.6KV MPP 332,1.6KV MPP 332,1.6KV MPP 332,1.6KV MPP
3 C710 224,250V MPP 224,250V MPP 224,250V MPP 304,250V MPP 334,250V MPP
7 T303 SCT-82D SCT-82D SCT-82D SCT-82 SCT-82
8 R730 2.4K,1/6W 1% 2.4K,1/6W 1% 2.4K,1/6W 1% 3.6K,1/6W 1% 3.6K,1/6W 1%
9 R215 1.2, 1/2W 1.2, 1/2W 1.2, 1/2W 1.2, 1/2W 1.2, 1/2W
10 R216 1.2, 1/2W 2.7, 1/2W 2.7, 1/2W 4.7, 1/2W 4.7, 1/2W
11 T701 ET-14 ET-14 ET-14 NONE NONE
12 C706 103,250V MPP 103,250V MPP 103,250V MPP NONE NONE
13 R715 100, 3W 100, 3W 100, 3W NONE NONE
14 R113 1,1W 1,1W 2.2, 3W 1,1W 1,1W
CRT
15 SINGLE DOUBLE DOUBLE SINGLE SINGLE
SOCKET
- 33 -

7. BLOCK DIAGRAM
AC SWITCHING 5V
INLET R,G,B VIDEO AMP
SOCKET IC ( 6S1265R) SWITCHING 6.3V
INPUT ( KA2506 ) VIDEO
12V OUTPUT
MODE CRT
14V OSD
POWER PROCESSOR
LINE BRIDGE -14V
DIODE ( WT6802 ) CUT-OFF
FILTER SUPPLY CONTROL
85V
FEEDBACK 130V
DEGAUSSING CONTROL I²C I² C
250V
I² C
DPMS OUTPUT
- SUSP END VERTICAL
- OFF SYNC DEFLECTION YOKE
OUTPUT - HIGH
MICRO I²C PROCESSOR
( TDA8172 ) V OLTAGE
LED
CONTROLLER (STV6888 - H.FOCUS
CONTROL - V.FOCUS
or - SCREE N
UNIT
TDA9116 ) HORIZO NTAL
H/V SYNC ( WT62P1 ) FLYBACK
INPUT DRIV E
OUTPUT
CIRCUIT TRANS DYNAMIC
STAGE FOCUS
ADJUST KEY DEFLECTION CIRCUIT
I² C S-CORRECTI
ON CIRCUIT
(S1~S4) B RIGHT
TLIT CONTROL
DDC 2BI
- H/V SIZE
- H/V POSI
TLIT - S-PIN HIGH
- TRAP HIGH V OLTAGE VOLTAGE
CONTROL - PARA HIGH V OLTAGE HIGH
P RO TECTIO N CIRCUIT
- PIN BAL DRIV E CIRCUIT
OUTPUT VOLTAGE
- ACL STAGE
- TILT REGULATION
TILT COIL - DEG
- 34 -

8. CONNECTING DIAGRAM
* CN407 & CN409orCN406= GGA/EGA
* CN405 & CN404= VGA/SVGA
15PIN VGA SIGNAL IN

CN407 CN404
CN405
ⓛ
CN406
5PIN,6PIN SIGNAL INPUT
CN401 CN409 CN801
ⓛ ⓛ PIN NO. CN4 06 CN409
① R-IN R-IN
② G-IN G-IN
③ B-IN B-IN
CN411
④ GND GND
⑤ V-S YNC H/V -SYNC
⑥ H-SYNC
CN807
CN401
- 35 -

9. SCHEMATIC
12V R102 H/V
TH101 180K,1W +5V
9OHM Q101 130V 12V 6.3V 5V CN411 CN801 5V 6.3V 12V 130V
R101 KSC1008 R103 1 1
47,1/4W 10K 2 2 5V 5 R
R104 R105 R106 L801 R802
DEGAUSS CN411 3 3 1K 130V
1K 220K 6.8K C103 1 SCL SCL BD L802
0.01U,500V
9 2 SDA 4 4 SDA C801 BD 3
CN102 9 D101 100U,16V Q801 G
C102 0.01U,500V 5 5 R803 R-CUTT
2
1 2 9 3
1N4148 0.015U,M 2N3904 10K
2 1 4 6 6 1 V_FLY R-GAIN
+
C809
C105 R107 7 7 R806 8 B
3
9 5 V-BLK V-BLK
0.01U,M 2K,1/4W,F 8 8 C803 1I C 8 0 1 16 1K R801R Q801R
DE-COIL 8mm H-FLY H-FLY 0.1U,50V VSSA VSS D803
V
1.5K,5W KSP44
H
6
-
RL101 C805 1N4148
S
2
S
9 9 2 15
U
HR-CR7 C106 7 N.C R-OSD
C
D
C804 1
O
N
O
10 10 3 14
R802R
R803R
0.22U,M R805 +5V
G
T
2
H
8 ACL-O ACL-O VCO G-OSD 10U,160V L801R
F
4 1 1K 0.0047U,M
3
R805R3
1 11 11 4 13
R807R 33,1/4W
1.2UH
330K
9 G1 G1 VDDA B-OSD
IC101 14V 14V-1 +12V
7
1
8
47K
12 12 5 12
LTV817 10 C808 H-S BLK
0.01U,M
D102 3 2 IC102 0.22U,M R808 R804R D801R CN803

2
13 13 6 N.C TEST 11
2200P,250VAC
KA431 11 680 1N4937 1 1

C107
12V R 8 1 0 100 7 SDA V-S 10 4.7K

SDA
33,1/4W
C108 L101 GT-1P
R804
R807
R809
R813
2200P,250VAC SCL 8 SCL VDD 9 390
D103 0.022U,M R109 D104 BD Q802 1 H_FLY R806R
4.7V 1.5K UF4004 R811 390 2N3904 R808R 100,1/2W +6.3V C1
N804 1
T101 100 WT6802 390 12V R812 220 D803R SG801R H-F
3
C109 18 390 3.9K 1N4148
C110 D806 200V
D807
D808
GT-1P
C111 TH102
3
8D13 +C 1 1 2 1N4148 R 8 1 5 680 L805 15*10*30 CN805
1000U,16V 1N4148 1 Q802R 1 1
BD
KSC3503
R111 1N4148 KSP92 V-F
2
0.22U,275VAC L103 C116 C801R
2
17
120K,1/2W 1
Q803R
BD 0.01U,500V 2 C810 1U,100V,BP L806 GT-1P
C802R
D805R
BAV21
IC802 BD C816
0.1U,M
D105 C113 CN 806 C N 810 7 C813 + 220U,16V C1
N808
3
1 28
T102 UF5404 +1 0 0 0 U , 1 6 V 1 R819 100 C812 R-OSD B/U 0.1U,50V 1000P,2K 1
200K,1/2W
LF-40T 6.3V R-OUT G2

R110
2 27
D106 2 2 G-OSD R-CLP L807 D804R
3
+
3 BD R 8 2 2 33,1/4W SG802 GT-1P
R112
3 26
UF5404 R113 G-OUT 3 3 R821 100 C814 B-OSD R-OUT 10V C803R R809R Q804R 1 1.5KV
C815 10P,50V 56K KSP92 R810R
0.1U,250V
16 4 VI/OSD G-CLP 25
2
4 4 68K,1/4W
2
C117 L808 R 8 2 5 33,1/4W
C804R
IC103 100K,1/2W 4
C119 5 R-IN G-OUT 24 0.1U,50V 1
470U,16V
C114 470P,1K 1.,1W 5 5 R824 100 C817

53S250V3.15A
B-OUT
R811R
220U,400V 15 470U,16V -14V 6 VCC1 VCC3 23 Q805R 12V
C118
BD KSP2222A
3
6 6
3.3K
4 2 +
R114 VFB GND 0.1U,50V 7 G 3 22
2
ND1 GND
D107 R813R
330K,1/2W R115 6 D108 0.1U,50V 8 G-IN B-OUT 21 L809 R 8 2 6 33,1/4W C805R 1
D809
D810
D811
200K,1/2W UF4007 UF1G

+
1N4148 0.1U,50V R814R 560 33P,50V SG803
DRAIN 1 68,1/4W 300V
0.01U,500V
9 VCC2 B-CLP 20
220,1/2W
1N4148 C819 Q806R
3
14
BD
1N4937
1N4148 0.1U,50V KSP44
F101
C122 L104 10 B-IN BLK 19 R812R
R830
C820
D812
C120 0.1U,50V 3 VCC VS/S 5
BD C121 D121 130V 11 GND(L) CLP 18
R814 200K
R827
R828
R829
0.22U,275VAC 220P,2K 31GF6 R 8 3 1 18K 12 17 390
80V ACL-O ABL R-CT 100 390
8 13
150K,1/4W
13 16
+ SCL R 8 3 2 100 SCL G-CT 390 G-CUTT-GAIN
6S1265R L105 14 15
100P,50V
100P,50V
R116 D109 BD SDA SDA B-CT
C834
4.7,1/4W UF4004
3.3U,50V
12 +
C101 L106 R833 R835 100
R108
0.1U,50V
KA2506 G1
47U,250V BD 100
C822
C806
C807
D110 + +
C123 31GF6
AC-IN 33U,50V R834 100
C125 7 11 B-CUTT-GAIN
100U,160V
CN103
33K,1/2W
1 2 1U,50V
UF4007
D111
0.1U,M
+
4
C127
2 1 R118 D112 250V C823 R836 100

6.8K,3W D113 220U,16V
R117
+
C126
10
90~264Vac1 0 m m
SPT-82 31GF6 31GF6
L107
T103 BD
1
C128 D114
0.1U,M 1N4148 SIGNAL INPUT
H_SYNC_IN
15P D-SUB
220K,1/2W
220K,1/2W
V_SYNC_IN
R119 60T C129
R121
R122
180,1W R-IN
VGA / SVGA
R120 +
G-IN CGA-Comp
270,1/4W R123 B-IN EGA-Comp
D116 L 1 0 8 BD H-OUT 330 OSD Control
UF4007 C130 5V
COMPOSITE-IN
T104 L 1 0 9 BD D117 D115 C131 47U,350V 2200P,250VAC CN401 CN403 R405 R406 SW401
0.0022U,M R-IN 1 4 1K 100
180UH UG8JT 1N4148 14V 12V G-IN
KEY 2 3 SW402
B-IN
R124 R125 D118 R126 3 2 R407 R 4 0 8 470
1M,1/2W 1M,1/2W 1N4937 390,1/2W LED
4 1 330 SW403
C132 IC105 14V-1 5V R409 1K
IC104 5V
0.068U,630V
0.001U,M 1 8
1 2 KA78R12 SW404
R410
6
FB VCC
10,1/4W
C133 D119 1 4 V - 1I C 1 0 6 VIDEO LEVEL VIDEO LEVEL
2
5.1V 1 KA7805 0.7Vpp 2.5Vpp D402
R402
180P,50V 2 V-CTRL DRV 7 1 Q102 IN OUT 3 R127 4 3 +C 1 3 5 R403 LED 2.4K
R401
1
C137 7N60 820K 470U,16V 15,1/4W

C136
CN404 CN405 CN406 CN409 CN407 8.2K

3
220P,50V
D
3 C/T GND 6 +
N
C138 Q401
2G
SUSPEND
2 4 R128 220U,16V Q103 C3203 CN402
1U,50V
4 5 6 1 2
C139
I-SENSE SYNC-I 10,1/4W C945YC R129

4.7K 2 1
R130 MC33260 H_SYNC_IN(C/S)
R-OUT D401 Q402
15K,1/4W 1N4148
3
D120 V_SYNC_IN
G-OUT Q403 A1270 ROTATION
GBU6J R131 R531 IC503/A C3202 +
B-OUT
H_SYNC_IN(C/S) 100 1 R532 IC503/B R-OUT ROTATION C402 C401
1M,1/2W 3
470 4
0.1U,M 4.7U,50V
G-OUT R404 12V
PFC-Option R533
2 6 H_SYNC-1 220K R701
47K C514 C515 5 B-OUT
D404
220P,50V 74HC86 680P,50V

R411
R412
R537 47,3W
5.6V
1
74HC86 C406
100
100
1K 0.1U,50V R702
R 4 1 4120
R 4 1 5120
R 4 1 6120
D403 CN410 C/S TABLE S1 S2 S3 1K,1/4W R703

IC503/C R535 R518 5.6V GT-1P R413 1.5K Q701
10
V_SYNC_IN
100 1K IC503/D 100 1 17K 이하 L L L Q702 C3203
R534 8 13
CN701 100 9 11
V_SYNC-1 H_LIN
C3198 R705
2 C516 12 C403 C404 C405 12V C702 2 17K~28K L L H 8.2K
1 R536 100P,50V 7 4 H C 8 6 C517 33P,50V 33P,50V 33P,50V 0.15U,250V
C701
47K 3 29K~34K L H H
1U,50V
+
0.1U,M 74HC86 R417 R418 R419
V-DY 80V 100 100 100 4 34K~38K H H H
C502 R706 R708 D701
0.01U,M 18K 1.2K 1N4148
R201 12V 5V C501 R709
22K 100K
10U,50V S1
Q703
V-FLY R301 Q704 19N20
R205 1,1/2W IC501 R710 C945YC
C945YC
0.22U,250V
Q201
1 8
R202 V-BLK 1.2K
470U,16V
A0 VCC
C301 2 A1 NC 7 R522
C705
15K R712
R 5 0 1 4.7K
R 5 0 2 4.7K
R 5 0 4 4.7K
560,1/4W
0.1U,M 100 R715

R 5 0 3 10K
+
R204
R 5 0 8 4.7K
R 5 0 9 4.7K
R 5 1 0 4.7K
R 5 1 1 4.7K
R 5 1 2 4.7K
4.7U,50V
3 6
8.2K C201 12V 10K,3W
R 5 0 6 10K
R 5 0 7 220
4 A2 SCL SCL 100,3W

4.7K
SDA 5 D-FOCUS
C304
1U,50V C303
R302
GND SDA
C302
C506
100P,50V
0.01U,M + 1000P,50V R524 C704

C41DC
+
-14V +14V 100 R716 220P,2K

0.47,1/2W
IC201 IC301 C503 +

18K R717
1.2,1/2W
C507
TDA8172 H-SYNC-2
1 H-S-I V-FOCUS 32
IC502 10U,50V C504 C505 1.2K R718
C305 R303 100 33P,50V 33P,50V T701
+
2 V-S-I SDA 31
R206
R207
V-SYNC-2 SDA 1 D+ D- 42 100K

UN-LOCK 102,100V(PP) 3
UNLOCK SCL
30
R304 100 SCL S2
Q706 DFT-82
1 IN(-)
7 IN(+)
R514 1K 19N20 C707

C
C
D
2 PWM2 V-S-I 41
0.56U,250V
R208
N
T
C
C
U
ACL V_SYNC1 Q707

4G
5O
Y
4 29
1000P,500V
L
2V
3F
6V
4.7K
FC1 VCC
R307 R513 R515 1K R719 C945YC C706
0.056U,M
3 PWM1 H-S-I 40 H_SYNC1

5 28
9.1K 2.2K 1.2K
R306
PLL2C B-OUT 4 39
C306
R308 PWM0 PWM3 R516 3.9K R517 27K,F H-SIZE 0.012U,250V
C709
1.2K
6 27
CO GND 6.8K 5
RESET PWM4
38
12V R720
1N4007GP
220U,16V
C204
C508
0.1U,50V
470U,16V
7 26
HGND H-OUT H-OUT 6 37
R305 VDD PWM5 82,2W +
UF4004
C203
10K C307 R309 47U,50V C708

+
+ 8 RO X-RAY 25
390,1/2W
7 36
GND PWM6 R519 4.7K H_LIN Q708
D202
C206
9 PLL1F EW-OUT 24 3.3U,50V,BP 10K,F R721 1U,50V
D702
C308 19N20
+
+ H-SIZE
8 OSC0 PWM7 35 18K R726 L701
R209
10 H-POS ROTATION R722

0.47U,63V(MP) V-OUT 23 C309 V-OUT1 100K,1/2W 7R5
9 OSC1 H-S-O 34 R521 100 H_SYNC-2
R724 220,3W LINEARITY COIL
11 H-FOCUS V-CAP 22 0.15U,M 10 33 100K CN701
C310 R310 SDA SDA2 V-S-O R523 100 V_SYNC-2 R723
+
12 H-FLY 1
C205 C207 H-FLY 1U,50V VGND 21 C311 11 32 1.2K
SCL SCL2 CLAMP S3 2
470U,16V 13 V-REF VGA-CAP 20
120P,50V
0.22U,M V-OUT2 2.7K 0.47U,63V(MP) 12 31

R525 Q709 D703
DEGAUSS PB3 PWM12 H/V-ADJ
R725 C945YC UF4004 H-DY
+
14 COMP VRB 19 C 3 1 2 4.7U,50V 13 30 5 3 2

R210 R526 PB2 PWM11 1.8K,1/4W 1.2K
C313
V-OUT1 R211 C208 1.5,1/2W,F 15 REG-IN VEHT 18 R 3 1 1 2.7K 100

0.0047U,M SUSPEND
14 PB1 PWM10 29
S3
10K,F L301 16 I-SENSE HEHT 17 R 3 1 2 2.7K C710
150UH LED
15 PB0 PWM9 28
S2
R212 R213 16 IRQ 0.27U,250V 250V
22K TDA9116 PWM8 27 S1
6.8K,F T303
R216 UN-LOCK R505 1K 17 PC7 SCL1 26 D704 SCT-82D C711
1.5,1/2W,F C713 R727 R728
PROTECTION 18 PC6 SDA1 25 1000P,500V 1 2 K , F 22K,1/4W,F BAV21 47U,350V
0.01U,500V
H-SIZE
V-OUT2 MUTE R529 100 19 PC5 PC0 24 C509 6 8 9
R214 12V 5V 5V 12V 10U,50V
R215 20 PC4 PC1 23 + L702 +
0.047U,M
X-RAY
30K,F R729 R730
C715
+C 2 0 9 1.5,1/2W,F KA358 21 PC3 PC2 22 47K 3K BD
8
KEY
R217 4.7U,50V R601 3 + IC601/A 5 +
R602
C712
5.6K 5.6K 2.2K WT62P1 R731

1 7
PROTECTION X-RAY X501 R530 750
22P,50V
2 - 6 -
12V 12MHz 2.2K C714
C513
80V 330P,1K Q710

4
+
C601 IC601/B C512 6.3V 11N40
R603 KA358
L602 10U,50V 4.7K 22P,50V C716 R733
47UH 100P,1K D705 L703 22,1/2W
H-FLY 1N4148 BD FUSEABLE
D601 R732
0.0033U,M
H/V
H-FLY 12V T702 R734
L601 V-F 4.7V Q601 1,1/2W
C717
BD KSP92 C718 GTT-82 FUSEABLE

5.6K
D602 H-F
D604 0.47U,63V(MP) 3 4
R605 T601 G2
1N4148 D706
R604 1N4148 12K,F 1N4148
0 .022U,M
0.1U,50V
R609 R607 HV MUTE C719

R613R614 6.2K C604 12V D707
+
D708
5.1K C603 2.2K 1 Q711

1K 390K 0.1U,250V(MP) D603 1 6U F 1 G
R612
1N4148
C606
22U,50V D605 1N4148 R608 C720 A733YC

5.6K
1N4148
D606
14 V-FLY 0.47U,63V(MP)
75,1/4W
1K 0.01U,M
10U,50V
C607 R610
C722
D714
+
2
R611 IC602 164 7 U , 5 0 V BAV21 39K R735 R736
+
1
220P,2K
1U,50V
1N4148
C721
1.5K + + Q603 G1
47,3W D711 Q712 C723 R737
1U,50V
Q602 SSS10N60 HF 6.8K

R740
R615 C724 C5584 D709

2
0.001,1.6K
2 15 +
C608
- - 2N3904
C612
VF 270K,1/4W 3 1 33U,50V T703 1N4148

D607 D608 UF4004
2
+ R616 1N4148 GUR460 HDT-82

75K
3 COMP VREF 14 1 4
1K 13
VR601 C725 D710
R739
+
C602 + 12V 1 6 R738 R741 1N4148

4 DEAD OUT 13 R618 100K L704 0.047U,M
3
18K
C610
100U,160V 1.2,3W 330K

22,1W
C609 D611 G2 BD
R752
0.0047,1.6K
D610
DTV56F
5 12 6
0.056U,M CT VCC 6.8,1/4W
D712
R621 GUR460 12 R742 IC701 12V

R617 R620 8 7
100V,472J(PP)
1N4148 6.8K 6 RT C2 11 R619 10,1/2W 1 COMP VREF 8

Q604 0.33,1W D612 11 200K,1/4W,F 10K Q713 C726 R746
C727
7 GND C2 10 5 Q605 Q607 4N20 R745 C729 680P,50V 2 VFB VI 7

8
2N3904 2N3904 R744 47 0.027U,M R747
10U,250V
1M,1/2W
C613
8 E1 9 ACL 6.8K 3 T 6
2N3904
C1 Q606 D615 UF4004 100 ISENSE OU 4.7,1/4W

10K,3W
10K,3W
2N3906 10 R622 12V

R623
UF4007
C616 R625 C728

R626
R627
+
0.1U,50V
7 4 5 +
C615
D613 + KA7500B R624 470 L604 L605 1K C737 L705 C731 0.0047,1.6K RT/CT GND C732 C730
R628
1N4148 1K BD BD R629 0.0022U,M BD 1000P,500V R748 D715 0.1U,50V 220U,16V

4.7K
+ 9
C617 2.7K + C 6 1 8 H-OUT Q714 1.2,3W UF4004 KA3883C
C614 33U,50V FQM19A002 D614 1U,50V C945YC C733
R630 D616 UF4007 0.22U,63V(MP) R749 C735
220U,16V 5.1K UF4007 7.5K 100V,472J(PP) R750
3.3U,50V,BP
Q715 75K C736

R633 C619 A733YC 0.01U,50V
H/V_ADJ
R631 C734
22K R751 330P,50V
C620
ACL-O 18K
R632 + 200K,1/4W,F 0.1U,250V(MP)
10K,1/4W,F C621 C622 D-FOCUS
4.7U,50V R634 3.3U,50V,BP D617
SG601
3.9K,1/4W,F 1.5KV 1N4148
- 36 -

10. PRINT CIRCUIT BOARD
10-1 MAIN
247mm
247mm
- 37 -

10-2 VIDEO
98mm
128mm
25mm
150mm
- 38 -

Kortek kt2914f

Uploaded by

Copyright:

Available Formats

Kortek kt2914f

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Kortek kt2914f

Uploaded by

Copyright:

Available Formats

What are the main sections covered in the manual?

What are the main sections covered in the manual?

What safety precautions should be observed when servicing the monitor?

What safety precautions should be observed when servicing the monitor?

COLOR CRT MONITOR DOC.

Downloaded from www.Manualslib.com manuals search engine

2. PRODUCT SPECIFICATION -------------------------------- 6

3. OPERATING INSTRUCTION -------------------------------- 9

5. TROUBLE SHOOTING GUIDE ---------------------------- 19

6. PART LIST ------------------------------------------------------- 29

7. BLOCK DIAGRAM -------------------------------------------- 34

8. CONNECTING DIAGRAM ----------------------------------- 35

10. PRINT CIRCUIT BOARD ---------------------------------- 37

Downloaded from www.Manualslib.com manuals search engine

1-1. Safety precautions

The followings are the necessary precautions to be observed before servicing.

1-1-1 Servicing the high voltage volume are CRT Warnings

Downloaded from www.Manualslib.com manuals search engine

TEST ALL LEAKAGE

ALSO TEST WITH

Figure 1-1. Leakage Current Test Circuit

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Deflection Angle 90° 90° 90° 90°

Focusing Method Sing le Double Sing le Sing le

Bandwidth Maximum 50MHz

Resolution Maximum Mode 800 X 600 @ 60Hz

Signal Input Connect 15 pin D-sub(Female) or Option(6Pin, 5Pin)

Input Current Operating :≤ 0.8Amps rms.

Downloaded from www.Manualslib.com manuals search engine

*CGA / EGA 6PIN CONNECTION ( PCB CKT NO. : CN406 )

*CGA / EGA 5PIN CONNECTION ( PCB CKT NO. : CN409 )

Downloaded from www.Manualslib.com manuals search engine

A : LINE TIME TOTAL B :HORIZONTAL SYNC WIDTH

O : FRAME TIME TOTAL P : VERTICAL SYNC WIDTH

CGA EGA VGA SVGA

f KHz 15.750 15.750 24.827 31.469 37.88

A uS 63.5 63.5 40.28 31.778 26.40

B uS 8.671 8.672 3.04 3.813 3.20

D uS 40.836 40.836 30.399 25.422 20.00

POL. POS POS POS NEG POS

f Hz 50 60.115 55.609 59.940 60.317

O mS 20.0 16.63 17.98 16.683 16.58

P mS 0.444 0.444 0.322 0.064 0.11

V Q mS 0.825 0.825 1.26 1.048 0.61

R mS 18.603 15.302 16.111 15.253 15.84

S mS 0.128 0.06 0.282 0.318 0.03

Downloaded from www.Manualslib.com manuals search engine

3-1 SET ASS'Y

3.2 MAIN PCB ASS'Y

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

4-1. Adjustment Control

4-1-2 TURN ON THE FACTORY OSD MANUAL METHOD

Downloaded from www.Manualslib.com manuals search engine

1) Click on the "MENU" button.

4-2-1 Screen center adjustment

a) Horizontal size adjustment