Implement Pump - Disassemble

18/6/2020 D6M TRACK-TYPE TRACTOR XL, LGP 3WN00001-UP (MACHINE) POWERED BY 3116 Engine(SEBP2486 - 116) - Documentación
Pantalla anterior
Bienvenido: cr461dec1
Producto: TRACK-TYPE TRACTOR
Modelo: D6M TRACK-TYPE TRACTOR 3WN01243
Configuración: D6M TRACK-TYPE TRACTOR XL, LGP 3WN00001-UP
(MACHINE) POWERED BY 3116 Engine
Desarmado y Armado
D6M Track-Type Tractor Machine Systems
Número de medio -SENR8391-02 Fecha de publicación -01/05/2004 Fecha de actualización -07/05/2004
i00959519
Implement Pump - Disassemble

SMCS - 5073-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
1P-0073 Shank 1
A
8B-7554 Bearing Cup Puller 1
B 1P-1857 Retaining Ring Pliers 1
Start By:
A. Remove the implement pump. Refer to Disassembly and Assembly, "Implement Pump -
Remove" for the machine that is being serviced.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=… 1/13
Illustration 1 g00717578
1. Remove O-ring seal (1) from pump (2) .
2. Remove bolts (4) that hold compensator (3) to the pump and remove the compensator.
3. Remove nut (5), screw (6), guide (7), spring (8), guide (9) and spool (10) from compensator
(3) .
4. Remove three seals (11) from the compensator.
5. Remove backup ring (12) and O-ring seal (13) from guide (7) .
6. Loosen nut (21) and remove screw (20) from compensator (3) .
7. Remove plug (19), guide (18), spring (16), guide (15) and spool (14) from the compensator.
8. Remove O-ring seal (17) from guide (18) .
9. Remove three plugs (22) and (23) from the compensator.
10. Remove the O-ring seals from plugs (22) and (23) .
11. Remove eight bolts (25) and valve block (24) from pump (2) .
12. Remove cylinder (26) and the spacer under the cylinder from valve block (24) .
13. Remove cylinder (27) and spring (28) from the valve block.
14. Remove the four bolts that hold flange (29) to valve block (24). Remove flange (29) and the
O-ring seal from the valve block.
15. Remove control piston (30) and bias piston (32) from valve block (24). Remove the O-ring
seal from each of the pistons.
16. Remove valve plate (31) from the valve block.
17. If necessary, use Tooling (A) and remove bearing cup (33) from valve block (24) .
18. If necessary, remove pin (35) from the valve block.
19. Remove plug (37) and three plugs (34) from the valve block. Remove the O-ring seal from
each of the plugs.
20. If necessary, remove seat (36), the poppet and the spring from the valve block.
21. Remove gasket (38) from pump (2) .
22. Remove bearing (39) from the shaft.
23. Remove spacer (40) and cylinder block (41) from the shaft.
24. Remove 6.4 mm (.250 inch) stock from the side of 4B-5274 9/16 inch Washer (43), as shown.
25. Use a press and a 4B-5274 9/16 inch Washer (43) in order to compress the spring. Remove
snap ring (42) from the groove in cylinder block (41) .
26. Release the tension on the spring.
27. Remove washer (44), spring (45) and washer (46) from cylinder block (41) .
28. Remove cover (47) from housing (48) .
29. Remove key (49) from housing (48) .
30. Rotate spacer (50). Remove spacer (50), cage (52) and nine pistons (51) .
31. Remove shaft (53) and swashplate (54) from housing (48) .
32. Remove dowel (56) from yoke (55) .
33. Remove cover (57) from housing (48) .
Note: Shims are located under spacer (58) .
34. Remove O-ring seal (59) and spacer (58) from both sides of the housing. Remove the shims
under spacer (58) .
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage… 10/13
35. Remove cup (60) and cone (61) from both sides of the housing.
36. Remove yoke (55) from housing (48) .
37. Remove two stops (62) from yoke (55) .
38. Remove bearing cone (63) from housing (48) .
39. If necessary, remove cup (64) with Tooling (A) .
40. If necessary, remove seal (65) from housing (48). Use Tool (B) in order to remove the snap
ring under seal (65) .
41. If necessary, remove seal (66) from housing (48). Use Tool (B) in order to remove the snap
ring under seal (66) .
Copyright 1993 - 2020 Caterpillar Inc. Thu Jun 18 2020 22:35:41 GMT-0500 (hora estándar de Colombia)
Todos los derechos reservados.
cr461dec1
Red privada para licenciados del SIS.

Implement Pump - Disassemble

Uploaded by

Copyright:

Available Formats

Implement Pump - Disassemble

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Implement Pump - Disassemble

Uploaded by

Copyright:

Available Formats

18/6/2020 D6M TRACK-TYPE TRACTOR XL, LGP 3WN00001-UP (MACHINE) POWERED BY 3116 Engine(SEBP2486 - 116) - Documentación

Implement Pump - Disassemble

Tool Part Number Part Description Qty

B 1P-1857 Retaining Ring Pliers 1

1. Remove O-ring seal (1) from pump (2) .

4. Remove three seals (11) from the compensator.

8. Remove O-ring seal (17) from guide (18) .

9. Remove three plugs (22) and (23) from the compensator.

16. Remove valve plate (31) from the valve block.

18. If necessary, remove pin (35) from the valve block.

21. Remove gasket (38) from pump (2) .

22. Remove bearing (39) from the shaft.

26. Release the tension on the spring.

28. Remove cover (47) from housing (48) .

29. Remove key (49) from housing (48) .

32. Remove dowel (56) from yoke (55) .

33. Remove cover (57) from housing (48) .

Note: Shims are located under spacer (58) .

36. Remove yoke (55) from housing (48) .

37. Remove two stops (62) from yoke (55) .

38. Remove bearing cone (63) from housing (48) .

39. If necessary, remove cup (64) with Tooling (A) .

You might also like