Examples 03

Examples
Chapter 3
PRESSURE AND FLUID STATICS
Prof. Dr. Ali PINARBAŞI

Yildiz Technical University
Mechanical Engineering Department
Yildiz, ISTANBUL
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
1
Pressure, Manometer, and Barometer
Sample Questions and Answers
2 Bölüm 5: KontrolChapter
Hacimleri için Kütle ve Enerji Çözümlemesi
3 PRESSURE AND FLUID STATICS
Prof. Dr. Ali Pınarbaşı
EXAMPLE 3–1
What is the difference between gage pressure and absolute pressure?
The pressure relative to the atmospheric pressure is called the gage pressure,
and the pressure relative to an absolute vacuum is called absolute pressure.
EXAMPLE 3–2
Explain why some people experience nose bleeding and some others experience
shortness of breath at high elevations.
The atmospheric air pressure which is the external pressure exerted on the skin
decreases with increasing elevation. Therefore, the pressure is lower at higher
elevations. As a result, the difference between the blood pressure in the veins and
the air pressure outside increases. This pressure imbalance may cause some
thin-walled veins such as the ones in the nose to burst, causing bleeding. The
shortness of breath is caused by the lower air density at higher elevations, and
thus lower amount of oxygen per unit volume.
EXAMPLE 3–3
Someone claims that the absolute pressure in a liquid of constant density doubles
when the depth is doubled. Do you agree? Explain.
No, the absolute pressure in a liquid of constant density does not double when the
depth is doubled. It is the gage pressure that doubles when the depth is doubled.
EXAMPLE 3–4
A tiny steel cube is suspended in water by a string. If the lengths of the sides of
the cube are very small, how would you compare the magnitudes of the pressures
on the top, bottom, and side surfaces of the cube?
If the lengths of the sides of the tiny cube suspended in water by a string are very
small, the magnitudes of the pressures on all sides of the cube will be the same.
EXAMPLE 3–5
Express Pascal’s law, and give a real-world example of it.
Pascal’s principle states that the pressure applied to a confined fluid increases the
pressure throughout by the same amount. This is a consequence of the pressure
in a fluid remaining constant in the horizontal direction. An example of Pascal’s
principle is the operation of the hydraulic car jack.
EXAMPLE 3–6
Consider two identical fans, one at sea level and the other on top of a high
mountain, running at identical speeds. How would you compare (a) the volume
flow rates and (b) the mass flow rates of these two fans?
The density of air at sea level is higher than the density of air on top of a high
mountain. Therefore, the volume flow rates of the two fans running at identical
speeds will be the same, but the mass flow rate of the fan at sea level will be
higher.
EXAMPLE 3–7
A vacuum gage connected to a chamber reads 24 kPa at a location where the
atmospheric pressure is 92 kPa. Determine the absolute pressure in the chamber.
Analysis The absolute pressure in the chamber is determined from
or,
Discussion Note that jumping horizontally from one tube to the next and realizing that
pressure remains the same in the same fluid simplifies the analysis greatly.
Assumptions The variation of the density of the liquid with depth is negligible.
Analysis The gage pressure at two different depths of a liquid can be expressed
as
Taking their ratio,
Discussion Note that the gage pressure in a given fluid is proportional to depth.
EXAMPLE 3–11
The absolute pressure in water at a depth of 5 m is read to be 145 kPa.
Determine (a) the local atmospheric pressure, and (b) the absolute pressure at a
depth of 5 m in a liquid whose specific gravity is 0.85 at the same location.
Analysis (a) Knowing the absolute pressure, the atmospheric pressure can be determined
from
(b) The absolute pressure at a depth of 5 m in the other liquid is
Discussion Note that at a given depth, the pressure in the lighter fluid is lower, as expected.
EXAMPLE 3–12
Assumptions 1 The weight of the person is distributed uniformly on the imprint

area of the shoes. 2 One foot carries the entire weight of a person during walking,
and the shoe is sized for walking conditions (rather than standing). 3 The weight
of the shoes is negligible.
Analysis The mass of the woman is given to be 70 kg. For a pressure of 0.5 kPa
on the snow, the imprint
area of one shoe must be
Discussion This is a very large area for a shoe, and such shoes would be
impractical to use. Therefore, some sinking of the snow should be allowed to
have shoes of reasonable size.
EXAMPLE 3–13
Then the absolute pressure in the tank becomes
EXAMPLE 3–14
A pressure gage connected to a tank reads 500 kPa at a location where the
atmospheric pressure is 94 kPa. Determine the absolute pressure in the tank.
Analysis The absolute pressure in the tank is determined from
EXAMPLE 3–15
which is also the distance climbed.
EXAMPLE 3–16
Taking an air column between the top and the bottom of the building
and writing a force balance per unit base area, we obtain
which is also the height of the building.

EXAMPLE 3–17
Determine the pressure exerted on a diver at 30 m below the free surface of the
sea. Assume a barometric pressureof 101 kPa and a specific gravity of 1.03 for
seawater.
Answer: 404.0 kPa
The pressure exerted on a diver at 30 m below the free

surface of the sea is the absolute pressure at that location:
EXAMPLE 3–18
Analysis Drawing the free body diagram of the piston and balancing the vertical
forces yield
Thus,
EXAMPLE 3–19
EXAMPLE 3–20
EXAMPLE 3–21
EXAMPLE 3–22
Repeat Prob. 3–29 for a differential mercury height of 30 mm.
EXAMPLE 3–23
Blood pressure is usually measured by wrapping a closed air-filled jacket
equipped with a pressure gage around the upper arm of a person at the level of
the heart. Using a mercury manometer and a stethoscope, the systolic pressure
(the maximum pressure when the heart is pumping) and the diastolic pressure
(the minimum pressure when the heart is resting) are measured in mmHg. The
systolic and diastolic pressures of a healthy person are about 120 mmHg and 80
mmHg, respectively, and are indicated as 120/80. Express both of these gage
pressures in kPa, psi, and meter water column.
Therefore,
Discussion Note that measuring blood pressure with a “water” monometer would
involve differential fluid heights higher than the person, and thus it is impractical.
This problem shows why mercury is a suitable fluid for blood pressure
measurement devices.
EXAMPLE 3–24
Solving for blood height and substituting gives
Discussion Note that the blood can rise about one and a half meters in a tube
connected to the vein. This explains why IV tubes must be placed high to force a
fluid into the vein of a patient.
EXAMPLE 3–25
Consider a 1.8-m-tall man standing vertically in water and completely submerged
in a pool. Determine the difference between the pressures acting at the head and
at the toes of this man, in kPa.
Substituting,
EXAMPLE 3–26
Setting them equal to each other and simplifying,
Discussion Note that the fluid height in the arm that contains oil is higher. This is expected
since oil is lighter than water.
EXAMPLE 3–27
The hydraulic lift in a car repair shop has an output diameter of 30 cm and is to lift
cars up to 2000 kg. Determine the fluid gage pressure that must be maintained in
the reservoir.
Assumptions The weight of the piston of the lift is negligible.

Analysis Pressure is force per unit area, and thus the gage pressure required is
simply the ratio of the weight of the car to the area of the lift,
Discussion Note that the pressure level in the reservoir can be reduced by using
a piston with a larger area.
EXAMPLE 3–28
Rearranging and neglecting the effect of air column on pressure,
Substituting,
Therefore, the pressure in the fresh water pipe is 3.39 kPa higher than the pressure in the
sea water pipe.
EXAMPLE 3–29
Repeat Prob. 3–36 by replacing the air with oil whose specific gravity is 0.72.
Rearranging,
Substituting,
Therefore, the pressure in the fresh water pipe is 8.34 kPa

higher than the pressure in the sea water pipe.
EXAMPLE 3–30
The gage pressure of the air in the tank shown in Fig. P3–40 is measured to be
65 kPa. Determine the differential height h of the mercury column.
Rearranging,
or,
Substituting,
Discussion Double instrumentation like this allows one to verify the measurement
of one of the instruments by the measurement of another instrument.
EXAMPLE 3–31
Repeat Prob. 3–40 for a gage pressure of 45 kPa.
Rearranging,
or,
Substituting,
Discussion Double instrumentation like this allows one to verify the measurement
of one of the instruments by the measurement of another instrument.
EXAMPLE 3–32
The top part of a water tank is divided into two compartments, as shown in Fig.
P3–42. Now a fluid with an unknown density is poured into one side, and the
water level rises a certain amount on the other side to compensate for this effect.
Based on the final fluid heights shown on the figure, determine the density of the
fluid added. Assume the liquid does not mix with water.
Discussion Note that the added fluid is lighter than water as expected (a heavier
fluid would sink in water).
EXAMPLE 3–33
The required oil height that will cause
4.34 kPa of pressure rise is
Therefore, a 500 kg load can be raised by this hydraulic lift by simply raising the oil level in
the tube by 56.7 cm.
Discussion Note that large weights can be raised by little effort in hydraulic lift by making
use of Pascal’s principle.
EXAMPLE 3–34
Substituting,
Discussion Using water or glycerin to measure atmospheric pressure requires
very long vertical tubes (over 10 m for water), which is not practical. This explains
why mercury is used instead of water or a light fluid..
EXAMPLE 3–35
A simple experiment has long been used to demonstrate how negative pressure
prevents water from being spilled out of an inverted glass. A glass that is fully filled
by water and covered with a thin paper is inverted, as shown in Fig. P3–46.
Determine the pressure at the bottom of the glass, and explain why water does
not fall out.
Analysis The paper is in equilibrium, and thus the net force acting on the paper
must be zero. A vertical force balance on the paper involves the pressure forces
on both sides, and yields
That is, the pressures on both sides of the paper must be

the same. The pressure at the bottom of the glass is
determined from the hydrostatic pressure relation to be
Substituting,
Discussion Note that there is a vacuum of 1 kPa at the bottom of the glass, and
thus there is an upward pressure force acting on the water body, which balanced
by the weight of water. As a result, the net downward force on water is zero, and
thus water does not flow down.
EXAMPLE 3–36
Two chambers with the same fluid at their base are separated by a piston whose
weight is 25 N, as shown in Fig. P3–47. Calculate the gage pressures in
chambers A and B.
The pressure at the bottom of each air
chamber is determined from the hydrostatic
pressure relation to be
2 The variation of pressure with elevation in each air chamber is
Substituting,
Discussion Note that there is a vacuum of about 2 kPa in tank B which pulls the
water up.
EXAMPLE 3–37
Consider a double-fluid manometer attached to an air pipe shown in Fig. P3–48. If
the specific gravity of one fluid is 13.55, determine the specific gravity of the other
fluid for the indicated absolute pressure of air. Take the atmospheric pressure to
be 100 kPa.
Answer: 5.0
Discussion Note that the right fluid column is higher than the left, and this would
imply above atmospheric pressure in the pipe for a single-fluid manometer.
EXAMPLE 3–38
Rearranging and using the definition of specific gravity,
Substituting,
Therefore, the pressure in the oil pipe is 27.7 kPa higher than the pressure in the water pipe.
Discussion Using a manometer between two pipes is not recommended unless the
pressures in the two pipes are relatively constant. Otherwise, an over-rise of pressure in one
pipe can push the manometer fluid into the other pipe, creating a short circuit.
EXAMPLE 3–39
Subtracting,
Substituting,
It gives
EXAMPLE 3–40
Rearranging and substituting the known values,
From geometric considerations,
Therefore,
Discussion Note that vertical distances are used in manometer analysis.

EXAMPLE 3–41
A multifluid container is connected to a U-tube, as shown in Fig. P3–52. For the
given specific gravities and fluid column heights, determine the gage pressure at
A. Also determine the height of a mercury column that would create the same
pressure at A.
Answers: 0.471 kPa, 0.353 cm
Rearranging and using the definition of specific gravity,
or
Substituting,
The equivalent mercury column height is
Discussion Note that the high density of mercury makes it a very suitable fluid for
measuring high pressures in manometers.
Fluid Statics: Hydrostatic Forces on Plane
and Curved Surfaces
EXAMPLE 3–42
Define the resultant hydrostatic force acting on a submerged surface, and the
center of pressure.
The resultant hydrostatic force acting on a submerged surface is the resultant of

the pressure forces acting on the surface. The point of application of this resultant
force is called the center of pressure.
EXAMPLE 3–43
Someone claims that she can determine the magnitude of the hydrostatic force
acting on a plane surface submerged in water regardless of its shape and
orientation if she knew the vertical distance of the centroid of the surface from the
free surface and the area of the surface. Is this a valid claim? Explain.
EXAMPLE 3–44
A submerged horizontal flat plate is suspended in water by a string attached at the
centroid of its upper surface. Now the plate is rotated 45° about an axis that
passes through its centroid. Discuss the change on the hydrostatic force acting
on the top surface of this plate as a result of this rotation. Assume the plate
remains submerged at all times.
EXAMPLE 3–45
You may have noticed that dams are much thicker at the bottom. Explain why
dams are built that way.
Dams are built much thicker at the bottom because the pressure force increases
with depth, and the bottom part of dams are subjected to largest forces.
EXAMPLE 3–46
Consider a submerged curved surface. Explain how you would determine the
horizontal component of the hydrostatic force acting on this surface.
The horizontal component of the hydrostatic force acting on a curved surface is

equal (in both magnitude and the line of action) to the hydrostatic force acting on
the vertical projection of the curved surface.
EXAMPLE 3–47
Consider a submerged curved surface. Explain how you would determine the
vertical component of the hydrostatic force acting on this surface.
The vertical component of the hydrostatic force acting on a curved surface is

equal to the hydrostatic force acting on the horizontal projection of the curved
surface, plus (minus, if acting in the opposite direction) the weight of the fluid
block.
EXAMPLE 3–48
Consider a circular surface subjected to hydrostatic forces by a constant density
liquid. If the magnitudes of the horizontal and vertical components of the resultant
hydrostatic force are determined, explain how you would find the line of action of
this force.
EXAMPLE 3–49
Consider a heavy car submerged in water in a lake with a flat bottom. The driver’s
side door of the car is 1.1 m high and 0.9 m wide, and the top edge of the door is
8 m below the water surface. Determine the net force acting on the door (normal
to its surface) and the location of the pressure center if (a) the car is well-sealed
and it contains air at atmospheric pressure and (b) the car is filled with water.
Then the resultant hydrostatic force on the door becomes
The pressure center is directly under the midpoint of the plate, and its distance
from the surface of the lake is determined to be
(b) When the car is filled with water, the net force normal to the surface of the
door is zero since the pressure on both sides of the door will be the same.
Discussion Note that it is impossible for a person to open the door of the car
when it is filled with atmospheric air. But it takes no effort to open the door when
car is filled with water.
EXAMPLE 3–50
Consider a 4-m-long, 4-m-wide, and 1.5-m-high aboveground swimming pool that
is filled with water to the rim. (a) Determine the hydrostatic force on each wall and
the distance of the line of action of this force from the ground. (b) If the height of
the walls of the pool is doubled and the pool is filled, will the hydrostatic force on
each wall double or quadruple? Why?
Answer: (a) 44.1 kN
Then the resultant hydrostatic force on each wall becomes
If the height of the walls of the pool is doubled, the hydrostatic force quadruples
since
EXAMPLE 3–51
A room in the lower level of a cruise ship has a 30-cm-diameter circular window. If
the midpoint of the window is 5 m below the water surface, determine the
hydrostatic force acting on the window, and the pressure center. Take the specific
gravity of seawater to be 1.025.
Answers: 3554 N, 5.001 m
The line of action of the force passes through the pressure

center, whose vertical distance from the free surface is
determined from
Discussion Note that for small surfaces deep in a liquid, the pressure center
nearly coincides with the centroid of the surface.
EXAMPLE 3–52
The water side of the wall of a 100-m-long dam is a quarter circle with a radius of
10 m. Determine the hydrostatic force on the dam and its line of action when the
dam is filled to the rim.
Horizontal force on vertical surface:
Vertical force on horizontal surface is zero since it coincides with the free surface
of water. The weight of fluid block per m length is
Then the magnitude and direction of the hydrostatic force
acting on the surface of the dam become
Therefore, the line of action of the hydrostatic force passes through the center of
the curvature of the dam, making 57.5° downwards from the horizontal.
EXAMPLE 3–53
A 4-m-high, 5-m-wide rectangular plate blocks the end of a 4-m-deep freshwater
channel, as shown in Fig.P3–66. The plate is hinged about a horizontal axis along
its upper edge through a point A and is restrained from opening by a fixed ridge at
point B. Determine the force exerted on the plate by the ridge.
The line of action of the force passes through the pressure center, which is 2h/3
from the free surface,
Taking the moment about point A and setting it equal to

zero gives
Solving for Fridge and substituting, the reaction force is

determined to be
EXAMPLE 3–54
A water trough of semicircular cross section of radius 0.5 m consists of two
symmetric parts hinged to each other at the bottom, as shown in Fig. P3–70. The
two parts are held together by a cable and turnbuckle placed every 3 m along
the length of the trough. Calculate the tension in each cable when the trough is
filled to the rim.
Assumptions 1 The atmospheric pressure acts on both sides of the trough wall,
and thus it can be ignored in calculations for convenience. 2 The weight of the
trough is negligible.
Properties We take the density of water to be 1000 kg/m3 throughout.
Analysis To expose the cable tension, we consider half of the trough whose
cross-section is quarter-circle. The hydrostatic forces acting on the vertical and
horizontal plane surfaces as well as the weight of the liquid block are:
The vertical force on the horizontal surface is zero, since it coincides with the free
surface of water. The weight of fluid block per 3-m length is
Then the magnitude and direction of the hydrostatic force acting on the surface of
the 3-m long section of the trough become
Therefore, the line of action passes through the center of the curvature of the
trough, making 57.5° downwards from the horizontal. Taking the moment about
point A where the two parts are hinged and setting it equal to zero gives
Solving for T and substituting, the tension in the cable is determined to be
Discussion This problem can also be solved without finding FR by finding the
lines of action of the horizontal hydrostatic force and the weight.
EXAMPLE 3–55
The two sides of a V-shaped water trough are hinged to each other at the bottom
where they meet, as shown in Fig. P3–71, making an angle of 45° with the ground
from both sides. Each side is 0.75 m wide, and the two parts are held together by
a cable and turnbuckle placed every 6 m along the length of the trough. Calculate
the tension in each cable when the trough is filled to the rim.
Answer: 5510 N
cross-section is triangular. The water height h at the midsection of the trough and
width of the free surface are
The hydrostatic forces acting on the vertical and horizontal

plane surfaces as well as the weight of the liquid block are
determined as follows:
The vertical force on the horizontal surface is zero since it coincides with the free
The distance of the centroid of a triangle from a side is 1/3 of the height of the
triangle for that side. Taking the moment about point A where the two parts are
hinged and setting it equal to zero gives
Solving for T and substituting, and noting that h = b, the tension in the cable is
determined to be
EXAMPLE 3–56
Repeat Prob. 3–71 for the case of a partially filled trough with a water height of
0.4 m directly above the hinge.
cross-section is triangular. The water height is given to be h = 0.4 m at the
midsection of the trough, which is equivalent to the width of the free surface b
since tan 45° = b/h = 1.
The hydrostatic forces acting on the vertical and horizontal plane surfaces as well
as the weight of the liquid block are determined as follows:
The vertical force on the horizontal surface is zero since it coincides with the free
The distance of the centroid of a triangle from a side is

1/3 of the height of the triangle for that side. Taking the
moment about point A where the two parts are hinged
and setting it equal to zero gives
Solving for T and substituting, and noting that h = b, the tension in the cable is
determined to be
EXAMPLE 3–57
A retaining wall against a mud slide is to be constructed by placing 0.8-m-high and
0.2-m-wide rectangular concrete blocks (r 2700 kg/m3) side by side, as shown in
Fig. P3–73. The friction coefficient between the ground and the concrete blocks is
f 0.3, and the density of the mud is about 1800 kg/m3. There is concern that the
concrete blocks may slide or tip over the lower left edge as the mud level rises.
Determine the mud height at which (a) the blocks will
overcome friction and start sliding and (b) the blocks will tip over.
Assumptions The atmospheric pressure acts on both sides of the wall, and thus
it can be ignored in calculations for convenience.
Properties The density is given to be 1800 kg/m3 for the mud, and 2700 kg/m3 for
concrete blocks.
Analysis (a) The weight of the concrete wall per unit length (L = 1 m) and the
friction force between the wall and the ground are
The hydrostatic force exerted by the mud to the wall is
Setting the hydrostatic and friction forces equal to each

other gives
(b) The line of action of the hydrostatic force passes through the pressure center,
which is 2h/3 from the free surface. The line of action of the weight of the wall
passes through the midplane of the wall. Taking the moment about point A and
setting it equal to zero gives
Solving for h and substituting, the mud height for tip over is determined to be
Discussion Note that the concrete wall will slide before tipping. Therefore, sliding
is more critical than tipping in this case.
EXAMPLE 3–58
Repeat Prob. 3–73 for 0.4-m-wide concrete blocks.
Assumptions The atmospheric pressure acts on both sides of the wall, and thus
Properties The density is given to be 1800 kg/m3 for the mud, and 2700 kg/m3 for
concrete blocks.
Analysis (a) The weight of the concrete wall per unit length (L = 1 m) and the
friction force between the wall and the ground are
The hydrostatic force exerted by the mud to the wall is
Setting the hydrostatic and friction forces equal to each other gives
(b) The line of action of the hydrostatic force passes through the pressure center,
which is 2h/3 from the free surface. The line of action of the weight of the wall
passes through the midplane of the wall. Taking the moment about point A and
setting it equal to zero gives
Solving for h and substituting, the mud height for tip over is determined to be
Discussion Note that the concrete wall will slide before tipping. Therefore, sliding
is more critical than tipping in this case.
EXAMPLE 3–59
A 4-m-long quarter-circular gate of radius 3 m and of negligible weight is hinged
about its upper edge A, as shown in Fig. P3–75. The gate controls the flow of
water over the ledge at B, where the gate is pressed by a spring. Determine the
minimum spring force required to keep the gate closed when the water level rises
to A at the upper edge of the gate.
Assumptions 1 The hinge is frictionless. 2 The atmospheric pressure acts on both sides of
the gate, and thus it can be ignored in calculations for convenience. 3 The weight of the gate
is negligible.
Analysis We consider the free body diagram of the liquid block enclosed by the circular
surface of the gate and its vertical and horizontal projections. The hydrostatic forces acting
on the vertical and horizontal plane surfaces as well as the weight of the liquid block are
Vertical force on horizontal surface (upward):
The weight of fluid block per 4-m length (downwards):
Therefore, the net upward vertical force is
Then the magnitude and direction of the hydrostatic force acting on the surface of the 4-m
long quarter-circular section of the gate become
Therefore, the magnitude of the hydrostatic force acting on the gate is 192.2 kN, and its line
of action passes through the center of the quarter-circular gate making an angle 23.2°
upwards from the horizontal.
The minimum spring force needed is determined by taking a moment about the point A
where the hinge is, and setting it equal to zero,
Solving for Fspring and substituting, the spring force is determined to be
EXAMPLE 3–60
Repeat Prob. 3–75 for a radius of 4 m for the gate.
Answer: 314 kN
Assumptions 1 The hinge is frictionless. 2 The atmospheric pressure acts on both sides of
the gate, and thus it can be ignored in calculations for convenience. 3 The weight of the gate
is negligible.
Analysis We consider the free body diagram of the liquid block enclosed by the circular
surface of the gate and its vertical and horizontal projections. The hydrostatic forces acting
on the vertical and horizontal plane surfaces as well as the weight of the liquid block are
Vertical force on horizontal surface (upward):
The weight of fluid block per 4-m length (downwards):
Therefore, the net upward vertical force is
Then the magnitude and direction of the hydrostatic force acting on the surface of
the 4-m long quarter-circular section of the gate become
Therefore, the magnitude of the hydrostatic force acting on the gate is 341.6 kN,
and its line of action passes through the center of the quarter-circular gate making
an angle 23.2° upwards from the horizontal.
The minimum spring force needed is determined by taking a moment about the
point A where the hinge is, and setting it equal to zero,
Solving for Fspring and substituting, the spring force is determined to be
Buoyancy
EXAMPLE 3–61
What is buoyant force? What causes it? What is the magnitude of the buoyant
force acting on a submerged body whose volume is V? What are the direction and
the line of action of the buoyant force?
The upward force a fluid exerts on an immersed body is called the buoyant force.
The buoyant force is caused by the increase of pressure in a fluid with depth. The
magnitude of the buoyant force acting on a submerged body whose volume is V is
expressed as FB = ρƒ gV The direction of the buoyant force is upwards, and its
line of action passes through the centroid of the displaced volume.
EXAMPLE 3–62
Consider two identical spherical balls submerged in water at different depths. Will
the buoyant forces acting on these two balls be the same or different? Explain.
The magnitude of the buoyant force acting on a submerged body whose volume is
V is expressed as FB = ρƒ gV which is independent of depth. Therefore, the
buoyant forces acting on two identical spherical balls submerged in water at
different depths will be the same.

EXAMPLE 3–63
Consider two 5-cm-diameter spherical balls—one made of aluminum, the other of
iron—submerged in water. Will the buoyant forces acting on these two balls be the
same or different? Explain.
V is expressed as FB = ρƒ gV, which is independent of the density of the body (ρƒ
is the fluid density). Therefore, the buoyant forces acting on the 5-cm diameter
aluminum and iron balls submerged in water will be the same.
EXAMPLE 3–64
Consider a 3-kg copper cube and a 3-kg copper ball submerged in a liquid. Will
the buoyant forces acting on these two bodies be the same or different? Explain.
V is expressed as FB = ρƒ gV, which is independent of the shape of the body.
Therefore, the buoyant forces acting on the cube and sphere made of copper
submerged in water will be the same since they have the same volume.

EXAMPLE 3–65
Discuss the stability of (a) a submerged and (b) a floating body whose center of
gravity is above the center of buoyancy.
A submerged body whose center of gravity G is above the center of buoyancy B,
which is the centroid of the displaced volume, is unstable. But a floating body may
still be stable when G is above B since the centroid of the displaced volume shifts
to the side to a point B’ during a rotational disturbance while the center of gravity
G of the body remains unchanged. If the point B’ is sufficiently far, these two
forces create a restoring moment, and return the body to the original position.

EXAMPLE 3–65
The density of a liquid is to be determined by an old 1-cm-diameter cylindrical
hydrometer whose division marks are completely wiped out. The hydrometer is
first dropped in water, and the water level is marked. The hydrometer is then
dropped into the other liquid, and it is observed that the mark for water has risen
0.5 cm above the liquid–air interface. If the height of the water mark is 10 cm,
determine the density of the liquid.

Properties We take the density of pure water to be 1000 kg/m3.
Analysis A hydrometer floating in water is in static equilibrium, and the buoyant force FB
exerted by the liquid must always be equal to the weight W of the hydrometer, FB = W.
where h is the height of the submerged portion of the

hydrometer and Ac is the cross-sectional area which is constant.
Setting the relations above equal to each other (since both

equal the weight of the hydrometer) gives
Solving for the liquid density and substituting,
Discussion Note that for a given cylindrical hydrometer, the product of the fluid density and
the height of the submerged portion of the hydrometer is constant in any fluid.
EXAMPLE 3–66
The volume and the average density of an irregularly shaped body are to be
determined by using a spring scale. The body weighs 7200 N in air and 4790 N in
water. Determine the volume and the density of the body. State your assumptions.
Properties We take the density of water to be 1000 kg/m3.
Assumptions 1 The buoyancy force in air is negligible. 2 The body is completely
submerged in water.
Analysis The mass of the body is
The difference between the weights in air and in water is due to the buoyancy
force in water,
Noting that FB = ρwater gV, the volume of the body is determined to be

Then the density of the body becomes
Discussion The volume of the body can also be measured by observing the
change in the volume of the container when the body is dropped in it (assuming
the body is not porous).
EXAMPLE 3–67
Consider a large cubic ice block floating in seawater. The specific gravities of ice
and seawater are 0.92 and 1.025, respectively. If a 10-cm-high portion of the ice
block extends above the surface of the water, determine the height of the ice
block below the surface.
Answer: 87.6 cm

Assumptions 1 The buoyancy force in air is negligible. 2 The top surface of the ice block is
parallel to the surface of the sea.
Properties The specific gravities of ice and seawater are given to be 0.92 and 1.025,
respectively, and thus the corresponding densities are 920 kg/m3 and 1025 kg/m3.
Analysis The weight of a body floating in a fluid is equal to the buoyant force acting on it (a
consequence of vertical force balance from static equilibrium). Therefore, in this case the
average density of the body must be equal to the density of the fluid since
The cross-sectional of a cube is constant, and thus the

“volume ratio” can be replaced by “height ratio”. Then,
where h is the height of the ice block below the surface.

Solving for h gives
Discussion Note that the 0.92/1.025 = 90% of the volume of an ice block remains under
water. For symmetrical ice blocks this also represents the fraction of height that remains
under water.
EXAMPLE 3–68
A 170-kg granite rock (ρ = 2700 kg/m3) is dropped into a lake. A man dives in and
tries to lift the rock. Determine how much force the man needs to apply to lift it
from the bottom of the lake. Do you think he can do it?
Assumptions 1 The rock is c completely submerged in water. 2 The buoyancy
force in air is negligible.
Properties The density of granite rock is given to be 2700 kg/m3. We take the
density of water to be 1000 kg/m3.
Analysis The weight and volume of the rock are
The buoyancy force acting on the rock is

The weight of a body submerged in water is equal to the weigh
of the body in air minus the buoyancy force,
Discussion This force corresponds to a mass of
Therefore, a person who can lift 47 kg on earth can lift this rock in water.

EXAMPLE 3–69
It is said that Archimedes discovered his principle during a bath while thinking
about how he could determine if King Hiero’s crown was actually made of pure
gold. While in the bathtub, he conceived the idea that he could determine the
average density of an irregularly shaped object by weighing it in air and also in
water. If the crown weighed 3.20 kgf (= 31.4 N) in air and 2.95 kgf (= 28.9 N) in
water, determine if the crown is made of pure gold. The density of gold is 19,300
kg/m3. Discuss how you can solve this problem without weighing the crown in
water but by using an ordinary bucket with no calibration for volume. You may
weigh anything in air.
Assumptions 1 The buoyancy force in air is negligible. 2 The crown is completely
submerged in water.
Properties We take the density of water to be 1000 kg/m3. The density of gold is
given to be 19300 kg/m3.
Analysis The mass of the crown is

The difference between the weights in air and in water is due to the buoyancy
force in water, and thus
Noting that FB = ρwater gV, the volume of the crown

is determined to be
Then the density of the crown becomes
which is considerably less than the density of gold. Therefore, the crown is NOT
made of pure gold.
Discussion This problem can also be solved without doing any under-water
weighing as follows: We would weigh a bucket half-filled with water, and drop the
crown into it. After marking the new water level, we would take the crown out, and
add water to the bucket until the water level rises to the mark. We would weigh
the bucket again. Dividing the weight difference by the density of water and g will
give the volume of the crown. Knowing both the weight and the volume of the
crown, the density can easily be determined.
EXAMPLE 3–70
One of the common procedures in fitness programs is to determine the fat-to-
muscle ratio of the body. This is based on the principle that the muscle tissue is
denser than the fat tissue, and, thus, the higher the average density of the body,
the higher is the fraction of muscle tissue. The average density of the body can be
determined by weighing the person in air and also while submerged in water in a
tank. Treating all tissues and bones (other than fat) as muscle with an equivalent
density of ρmuscle, obtain a relation for the volume fraction of body fat xfat.
Answer: xfat (ρmuscle ρave)/(ρmuscle ρfat).
Assumptions 1 The buoyancy force in air is
negligible. 2 The body is considered to consist of fat
and muscle only. 3 The body is completely
submerged in water, and the air volume in the lungs
is negligible.
Analysis The difference between the weights of the
person in air and in water is due to the buoyancy
force in water. Therefore,

Knowing the weights and the density of water, the relation above gives the volume of the
person. Then the average density of the person can be determined from
Under assumption #2, the total mass of a person is equal to the sum of the masses of the
fat and muscle tissues, and the total volume of a person is equal to the sum of the volumes
of the fat and muscle tissues. The volume fraction of body fat is the ratio of the fat volume to
the total volume of the person. Therefore,
Noting that mass is density times volume, the last relation

can be written as
Canceling the V and solving for xfat gives the desired

relation,
Discussion Weighing a person in water in order to determine its volume is not practical. A
more practical way is to use a large container, and measuring the change in volume when
the person is completely submerged in it.
EXAMPLE 3–71
The hull of a boat has a volume of 150 m3, and the total mass of the boat when
empty is 8560 kg. Determine how much load this boat can carry without sinking
(a) in a lake and (b) in seawater with a specific gravity of 1.03.
Assumptions 1 The dynamic effects of the waves are disregarded. 2 The
buoyancy force in air is negligible.
Properties The density of sea water is given to be 1.03×1000 = 1030 kg/m3. We
take the density of water to be 1000 kg/m3.
Analysis The weight of the unloaded boat is
The buoyancy force becomes a maximum when the entire hull of the boat is
submerged in water, and is determined to be

The total weight of a floating boat (load + boat itself) is equal to the buoyancy
force. Therefore, the weight of the maximum load is
The corresponding masses of load are
Discussion Note that this boat can carry 4500 kg more load in the sea than it can
in fresh water. The fully-loaded boats in sea water should expect to sink into water
deeper when they enter fresh water such a river where the port may be.
Fluids in Rigid-Body Motion

EXAMPLE 3–72
Under what conditions can a moving body of fluid be treated as a rigid body?
A moving body of fluid can be treated as a rigid body when there are no shear
stresses (i.e., no motion between fluid layers relative to each other) in the fluid
body.
EXAMPLE 3–73
Consider a glass of water. Compare the water pressures at the bottom surface for
the following cases: the glass is (a) stationary, (b) moving up at constant velocity,
(c) moving down at constant velocity, and (d) moving horizontally at constant
velocity.
A glass of water is considered. The water pressure at the bottom surface will be
the same since the acceleration for all four cases is zero.

EXAMPLE 3–74
Consider two identical glasses of water, one stationary and the other moving on a
horizontal plane with constant acceleration. Assuming no splashing or spilling
occurs, which glass will have a higher pressure at the (a) front, (b) midpoint, and
(c) back of the bottom surface?
The pressure at the bottom surface is constant when the glass is stationary. For a
glass moving on a horizontal plane with constant acceleration, water will collect at
the back but the water depth will remain constant at the center. Therefore, the
pressure at the midpoint will be the same for both glasses. But the bottom
pressure will be low at the front relative to the stationary glass, and high at the
back (again relative to the stationary glass). Note that the pressure in all cases is
the hydrostatic pressure, which is directly proportional to the fluid height.

EXAMPLE 3–75
Consider a vertical cylindrical container partially filled with water. Now the cylinder
is rotated about its axis at a specified angular velocity, and rigid-body motion is
established. Discuss how the pressure will be affected at the midpoint and at the
edges of the bottom surface due to rotation.
When a vertical cylindrical container partially filled with water is rotated about its
axis and rigid body motion is established, the fluid level will drop at the center and
rise towards the edges. Noting that hydrostatic pressure is proportional to fluid
depth, the pressure at the mid point will drop and the pressure at the edges of the
bottom surface will rise due to rotation.

EXAMPLE 3–76
A water tank is being towed by a truck on a level road, and the angle the free
surface makes with the horizontal is measured to be 15°. Determine the
acceleration of the truck.
Assumptions 1 The road is horizontal so that acceleration has

no vertical component (ɑz = 0). 2 Effects of splashing, breaking,
driving over bumps, and climbing hills are assumed to be
secondary, and are not considered. 3 The acceleration remains
constant.
Analysis We take the x-axis to be the direction of motion, the z-
axis to be the upward vertical direction. The tangent of the angle
the free surface makes with the horizontal is
Solving for ax and substituting,
Discussion Note that the analysis is valid for any fluid with constant density since
we used no information that pertains to fluid properties in the solution.
EXAMPLE 3–77
Consider two water tanks filled with water. The first tank is 8 m high and is
stationary, while the second tank is 2 m high and is moving upward with an
acceleration of 5 m/s2. Which tank will have a higher pressure at the bottom?
Assumptions 1 The acceleration remains constant. 2 Water is an incompressible

substance.
Properties We take the density of water to be 1000 kg/m3.
Analysis The pressure difference between two points 1 and 2 in an
incompressible fluid is given by

since ɑx = 0. Taking point 2 at the free surface and point 1 at the tank bottom, we
have P2 = Patm and z2 – z1 = h and thus
Tank A: We have az = 0, and thus the pressure at the bottom is
Tank B: We have az = +5 m/s2, and thus the pressure at the bottom is
Therefore, tank A has a higher pressure at the bottom.

Discussion We can also solve this problem quickly by examining the relation
Pbottom = ρ(g + ɑz)h. Acceleration for tank B is about 1.5 times that of Tank A (14.81
vs 9.81 m/s2), but the fluid depth for tank A is 4 times that of tank B (8 m vs 2 m).
Therefore, the tank with the larger acceleration-fluid height product (tank A in this
case) will have a higher pressure at the bottom.
EXAMPLE 3–78
A water tank is being towed on an uphill road that makes 20° with the horizontal
with a constant acceleration of 5 m/s2 in the direction of motion. Determine the
angle the free surface of water makes with the horizontal. What would your
answer be if the direction of motion were downward on the same road with the
same acceleration?

Assumptions 1 Effects of splashing, breaking, driving over bumps, and climbing
hills are assumed to be secondary, and are not considered. 2 The acceleration
remains constant.
Analysis We take the x- and z-axes as shown in the figure. From geometrical
considerations, the horizontal and vertical components of acceleration are
The tangent of the angle the free surface makes with the horizontal is
When the direction of motion is reversed, both ax and az are in negative x- and z-
direction, respectively, and thus become negative quantities,
Then the tangent of the angle the free surface makes with the horizontal becomes
Discussion Note that the analysis is valid for any fluid with constant density, not
just water, since we used no information that pertains to water in the solution.
EXAMPLE 3–79
A 60-cm-high, 40-cm-diameter cylindrical water tank is being transported on a
level road. The highest acceleration anticipated is 4 m/s2. Determine the allowable
initial water height in the tank if no water is to spill out during acceleration.
Answer: 51.8 cm

Assumptions 1 The road is horizontal during acceleration so that acceleration
has no vertical component (az = 0). 2 Effects of splashing, breaking, driving over
bumps, and climbing hills are assumed to be secondary, and are not considered.
3 The acceleration remains constant.
Analysis We take the x-axis to be the direction of motion, the z-axis to be the
upward vertical direction, and the origin to be the midpoint of the tank bottom. The
tangent of the angle the free surface makes with the horizontal is
The maximum vertical rise of the free surface occurs at the back of the tank, and
the vertical midplane experiences no rise or drop during acceleration. Then the
maximum vertical rise at the back of the tank relative to the midplane is
Therefore, the maximum initial water height in the tank to avoid spilling is
Discussion Note that the analysis is valid for any fluid with constant density, not
just water, since we used no information that pertains to water in the solution.
EXAMPLE 3–80
A 40-cm-diameter, 90-cm-high vertical cylindrical container is partially filled with
60-cm-high water. Now the cylinder is rotated at a constant angular speed of 120
rpm. Determine how much the liquid level at the center of the cylinder will drop as
a result of this rotational motion.

Assumptions 1 The increase in the rotational speed is very slow so that the liquid
in the container always acts as a rigid body. 2 The bottom surface of the container
remains covered with liquid during rotation (no dry spots).
Analysis Taking the center of the bottom surface of the rotating vertical cylinder
as the origin (r = 0, z = 0), the equation for the free surface of the liquid is given as
where h0 = 0.6 m is the original height of the liquid before rotation, and
Then the vertical height of the liquid at the center of the container where r = 0
becomes
Therefore, the drop in the liquid level at the center of the cylinder is
Discussion Note that the analysis is valid for any liquid since the result is
independent of density or any other fluid property. Also, our assumption of no dry
spots is validated since z0(0) is positive.
EXAMPLE 3–81
A fish tank that contains 40-cm-high water is moved in the cabin of an elevator.
Determine the pressure at the bottom of the tank when the elevator is (a)
stationary, (b) moving up with an upward acceleration of 3 m/s2, and (c) moving
down with a downward acceleration of 3 m/s2.
Assumptions 1 The acceleration

remains constant. 2 Water is an
incompressible substance.
Properties We take the density of
water to be 1000 kg/m3.
Analysis The pressure difference
between two points 1 and 2 in an
incompressible fluid is given by
since ax = 0. Taking point 2 at the free surface and point 1 at the tank bottom, we
have P2 = Patm and z2 – z1 = h and thus

(a) Tank stationary: We have az = 0, and thus the gage pressure at the tank
bottom is
(b) Tank moving up: We have az = +3 m/s2, and thus the gage pressure at the
tank bottom is
(c) Tank moving down: We have az = -3 m/s2, and thus the gage pressure at the
tank bottom is
Discussion Note that the pressure at the tank bottom while moving up in an
elevator is almost twice that while moving down, and thus the tank is under much
greater stress during upward acceleration.

EXAMPLE 3–82
A 3-m-diameter vertical cylindrical milk tank rotates at a constant rate of 12 rpm. If
the pressure at the center of the bottom surface is 130 kPa, determine the
pressure at the edge of the bottom surface of the tank. Take the density of the
milk to be 1030 kg/m.
Assumptions 1 The increase in the rotational speed is
very slow so that the liquid in the container always acts
as a rigid body. 2 Milk is an incompressible substance.
Properties The density of the milk is given to be 1030
kg/m3.
Analysis Taking the center of the bottom surface of the
rotating vertical cylinder as the origin (r = 0, z = 0), the
equation for the free surface of the liquid is given as
where R = 1.5 m is the radius, and

The fluid rise at the edge relative to the center of the tank is
The pressure difference corresponding to this fluid height difference is
Then the pressure at the edge of the bottom surface becomes
Discussion Note that the pressure is 1.4% higher at the edge relative to the
center of the tank, and there is a fluid level difference of 1.18 m between the edge
and center of the tank, and these differences should be considered when
designing rotating fluid tanks.

EXAMPLE 3–83
Milk with a density of 1020 kg/m3 is transported on a level road in a 7-m-long, 3-
m-diameter cylindrical tanker. The tanker is completely filled with milk (no air
space), and it accelerates at 2.5 m/s2. If the minimum pressure in the tanker is
100 kPa, determine the maximum pressure and its location.
Answer: 47.9 kPa

Assumptions 1 The acceleration remains constant. 2 Milk is an incompressible
substance.
Properties The density of the milk is given to be 1020 kg/m3.
Analysis We take the x- and z- axes as shown. The horizontal acceleration is in
the negative x direction, and thus ax is negative. Also, there is no acceleration in
the vertical direction, and thus az = 0. The pressure difference between two points
1 and 2 in an incompressible fluid in linear rigid body motion is given by

The first term is due to acceleration in the horizontal direction and the resulting
compression effect towards the back of the tanker, while the second term is
simply the hydrostatic pressure that increases with depth. Therefore, we reason
that the lowest pressure in the tank will occur at point 1 (upper front corner), and
the higher pressure at point 2 (the lower rear corner). Therefore, the maximum
pressure difference in the tank is
Discussion Note that the variation of pressure along a horizontal line is due to
acceleration in the horizontal direction while the variation of pressure in the
vertical direction is due to the effects of gravity and acceleration in the vertical
direction (which is zero in this case).

EXAMPLE 3–84
Repeat Prob. 3–102 for a deceleration of 2.5 m/s2.
Assumptions 1 The acceleration remains constant. 2 Milk is an incompressible

substance.
Properties The density of the milk is given to be 1020 kg/m3.
Analysis We take the x- and z- axes as shown. The horizontal deceleration is in
the x direction, and thus ax is positive. Also, there is no acceleration in the vertical
direction, and thus az = 0. The pressure difference between two points 1 and 2 in
an incompressible fluid in linear rigid body motion is given by

The first term is due to deceleration in the horizontal direction and the resulting
compression effect towards the front of the tanker, while the second term is simply
the hydrostatic pressure that increases with depth. Therefore, we reason that the
lowest pressure in the tank will occur at point 1 (upper front corner), and the
higher pressure at point 2 (the lower rear corner). Therefore, the maximum
pressure difference in the tank is
Discussion Note that the variation of pressure along a horizontal line is due to
acceleration in the horizontal direction while the variation of pressure in the
vertical direction is due to the effects of gravity and acceleration in the vertical
direction (which is zero in this case).
EXAMPLE 3–85
The distance between the centers of the two arms of a U-tube open to the
atmosphere is 25 cm, and the U-tube contains 20-cm-high alcohol in both arms.
Now the U-tube is rotated about the left arm at 4.2 rad/s. Determine the elevation
difference between the fluid surfaces in the two arms.

Assumptions 1 Alcohol is an
incompressible fluid.
Analysis Taking the base of the
left arm of the U-tube as the origin
(r = 0, z = 0), the equation for the
free surface of the liquid is given
as
where h0 = 0.20 m is the original height of the liquid before rotation, and ω = 4.2
rad/s. The fluid rise at the right arm relative to the fluid level in the left arm (the
center of rotation) is
Discussion Note that the analysis is valid for any liquid since the result is
independent of density or any other fluid property.

EXAMPLE 3–86
A 1.2-m-diameter, 3-m-high sealed vertical cylinder is completely filled with
gasoline whose density is 740 kg/m3. The tank is now rotated about its vertical
axis at a rate of 70 rpm. Determine (a) the difference between the pressures at
the centers of the bottom and top surfaces and (b) the difference between the
pressures at the center and the edge of the bottom surface.
The

Assumptions 1 The increase in the rotational speed
is very slow so that the liquid in the container always
acts as a rigid body. 2 Gasoline is an incompressible
substance.
Properties The density of the gasoline is given to be
740 kg/m3.
Analysis The pressure difference between two points
1 and 2 in an incompressible fluid rotating in rigid body
motion is given by
(a) Taking points 1 and 2 to be the centers of the bottom and top surfaces,
respectively, we have r1 = r2 = 0 and z2 – z1 = h = 3 m. Then,

(b) Taking points 1 and 2 to be the center and edge of the bottom surface,
respectively, we have r1 = 0,
Discussion Note that the rotation of the tank does not affect the pressure
difference along the axis of the tank. But the pressure difference between the
edge and the center of the bottom surface (or any other horizontal plane) is due
entirely to the rotation of the tank.

EXAMPLE 3–87
A 3-m-diameter, 7-m-long cylindrical tank is completely filled with water. The tank
is pulled by a truck on a level road with the 7-m-long axis being horizontal.
Determine the pressure difference between the front and back ends of the tank
along a horizontal line when the truck (a) accelerates at 3 m/s2 and (b)
decelerates at 4 m/s2.
Assumptions 1 The acceleration remains constant. 2 Water is an incompressible

substance.
Properties We take the density of the water to be 1000 kg/m3.
Analysis (a) We take the x- and z- axes as shown. The horizontal acceleration is
in the negative x direction, and thus ax is negative. Also, there is no acceleration in
the vertical direction, and thus az = 0. The pressure difference between two points
1 and 2 in an incompressible fluid in linear rigid body motion is given by
since z2 – z1 = 0 along a horizontal line. Therefore, the pressure difference
between the front and back of the tank is due to acceleration in the horizontal
direction and the resulting compression effect towards the back of the tank. Then
the pressure difference along a horizontal line becomes
(b) The pressure difference during deceleration is determined the way, but ax = 4
m/s2 in this case,
Discussion Note that the pressure is higher at the back end of the tank during
acceleration, but at the front end during deceleration (during breaking, for
example) as expected.
Review Problems

EXAMPLE 3–88
An air-conditioning system requires a 20-m-long section of 15-cm-diameter
ductwork to be laid underwater. Determine the upward force the water will exert
on the duct. Take the densities of air and water to be 1.3 kg/m3 and 1000 kg/m3,
respectively.
Assumptions 1 The diameter given is the outer diameter of the duct (or, the thickness of
the duct material is negligible). 2 The weight of the duct and the air in is negligible.
Properties The density of air is given to be ρ = 1.30 kg/m3. We take the density of water to
be 1000 kg/m3.
Analysis Noting that the weight of the duct and the air in it is negligible, the net upward
force acting on the duct is the buoyancy force exerted by water. The volume of the
underground section of the duct is
Then the buoyancy force becomes
Discussion The upward force exerted by water on the duct is 3.47 kN, which is equivalent
to the weight of a mass of 354 kg. Therefore, this force must be treated seriously.

EXAMPLE 3–89
Balloons are often filled with helium gas because it weighs only about one-
seventh of what air weighs under identical conditions. The buoyancy force, which
can be expressed as Fb = ρairgVballoon, will push the balloon upward. If the balloon
has a diameter of 10 m and carries two people, 70 kg each, determine the
acceleration of the balloon when it is first released. Assume the density of air is
ρ = 1.16 kg/m3, and neglect the weight of the ropes and the cage.
Answer: 16.5 m/s2
Assumptions The weight of the cage and the ropes of the balloon
is negligible.
Properties The density of air is given to be ρ = 1.16 kg/m3. The
density of helium gas is 1/7th of this.
Analysis The buoyancy force acting on the balloon is

The total mass is
The total weight is
Thus the net force acting on the balloon is
Then the acceleration becomes

EXAMPLE 3–90
Determine the maximum amount of load, in kg, the balloon described in Prob. 3–
111 can carry.
Answer: 520.6 kg
Assumptions The weight of the cage and the ropes of
the balloon is negligible.
Properties The density of air is given to be ρ = 1.16
kg/m3. The density of helium gas is 1/7th of this.
Analysis In the limiting case, the net force acting on the
balloon will be zero. That is, the buoyancy force and the
weight will balance each other:

EXAMPLE 3–91
The basic barometer can be used as an altitudemeasuring device in airplanes.
The ground control reports a barometric reading of 753 mmHg while the pilot’s
reading is 690 mmHg. Estimate the altitude of the plane from ground level if the
average air density is 1.20 kg/m3.
Answer: 714 m
Assumptions The variation of air density with altitude is
negligible.
Properties The densities of air and mercury are given to be
ρ = 1.20 kg/m3 and ρ = 13,600 kg/m3.
Analysis Atmospheric pressures at the location of the plane
and the ground level are

Taking an air column between the airplane and the ground and writing a force
balance per unit base area, we obtain
which is also the altitude of the airplane.

EXAMPLE 3–92
The lower half of a 10-m-high cylindrical container is filled with water (ρ = 1000
kg/m3) and the upper half with oil that has a specific gravity of 0.85. Determine
the pressure difference between the top and bottom of the cylinder.
Answer: 90.7 kPa
Properties The density of water is given to be
ρ = 1000 kg/m3. The specific gravity of oil is given to
be 0.85.
Analysis The density of the oil is obtained by
multiplying its specific gravity by the density of water,
3-84
The pressure difference between the top and the

bottom of the cylinder is the sum of the pressure
differences across the two fluids,

EXAMPLE 3–93
A vertical, frictionless piston–cylinder device contains a gas at 500 kPa. The
atmospheric pressure outside is 100 kPa, and the piston area is 30 cm2.
Determine the mass of the piston.
Assumptions There is no friction between the piston and the cylinder.

Analysis Drawing the free body diagram of the piston and balancing the vertical
forces yield

EXAMPLE 3–94
A pressure cooker cooks a lot faster than an ordinary pan by maintaining a higher pressure
and temperature inside. The lid of a pressure cooker is well sealed, and steam can escape
only through an opening in the middle of the lid. A separate metal piece, the petcock, sits on
top of this opening
and prevents steam from escaping until the pressure force overcomes the weight of the
petcock. The periodic escape of the steam in this manner prevents any potentially
dangerous pressure buildup and keeps the pressure inside at a constant value. Determine
the mass of the petcock of a pressure cooker whose operation pressure is 100 kPa gage
and has an opening cross-sectional area of 4 mm2. Assume an atmospheric pressure of 101
kPa, and draw the free-body diagram of the petcock. Answer: 40.8 g

Assumptions There is no blockage of the pressure release valve.
Analysis Atmospheric pressure is acting on all surfaces of the petcock, which
balances itself out. Therefore, it can be disregarded in calculations if we use the
gage pressure as the cooker pressure. A force balance on the petcock (ΣFy = 0)
yields

EXAMPLE 3–95
A glass tube is attached to a water pipe, as shown in Fig. P3–119. If the water
pressure at the bottom of the tube is 115 kPa and the local atmospheric pressure
is 92 kPa, determine how high the water will rise in the tube, in m. Assume
g 9.8 = m/s2 at that location and take the density of water to be 1000 kg/m3.
Properties The density of water is given to be
ρ = 1000 kg/m3.
Analysis The pressure at the bottom of the tube can be
expressed as
Solving for h,

EXAMPLE 3–96
The average atmospheric pressure on earth is approximated as a function of
altitude by the relation Patm = 101.325 (1 – 0.02256z)5.256, where Patm is the
atmospheric pressure in kPa and z is the altitude in km with z = 0 at sea level.
Determine the approximate atmospheric pressures at Atlanta (z = 306 m), Denver
(z = 1610 m), Mexico City (z = 2309 m), and the top of Mount Everest (z = 8848
m).
Analysis The atmospheric pressures at various locations are obtained by

substituting the altitude z values in km into the relation

EXAMPLE 3–97
When measuring small pressure differences with a manometer, often one arm of
the manometer is inclined to improve the accuracy of reading. (The pressure
difference is still proportional to the vertical distance and not the actual length of
the fluid along the tube.) The air pressure in a circular duct is to be measured
using a manometer whose open arm is inclined 35° from the horizontal, as shown
in Fig. P3–121. The density of the liquid in the manometer is 0.81 kg/L, and the
vertical distance between the fluid levels in the two arms of the manometer is 8
cm. Determine the gage pressure of air in the duct and the length of the fluid
column in the inclined arm above the fluid level in the vertical arm.

Assumptions The manometer fluid is an incompressible substance.
Properties The density of the liquid is given to be ρ = 0.81 kg/L = 810 kg/m3.
Analysis The gage pressure in the duct is determined from
The length of the differential fluid column is
Discussion Note that the length of the differential fluid column is extended
considerably by inclining the manometer arm for better readability.

EXAMPLE 3–98
Intravenous infusions are usually driven by gravity by hanging the fluid bottle at
sufficient height to counteract the blood pressure in the vein and to force the fluid
into the body. The higher the bottle is raised, the higher the flow rate of the fluid
will be. (a) If it is observed that the fluid and the blood pressures balance each
other when the bottle is 1.2 m above the arm level, determine the gage pressure
of the blood. (b) If the gage pressure of the fluid at the arm level needs to be 20
kPa for sufficient flow rate, determine how high the bottle must be placed. Take
the density of the fluid to be 1020 kg/m3.

Assumptions 1 The IV fluid is incompressible. 2 The IV bottle is open to the atmosphere.
Properties The density of the IV fluid is given to be ρ = 1020 kg/m3.
Analysis (a) Noting that the IV fluid and the blood pressures balance each other when the
bottle is 1.2 m above the arm level, the gage pressure of the blood in the arm is simply
equal to the gage pressure of the IV fluid at a depth of 1.2 m,
(b) To provide a gage pressure of 20 kPa at the arm level, the height
of the bottle from the arm level is again determined from pgage,arm =
ρgharm-bottle to be
Discussion Note that the height of the reservoir can be used to control flow rates in gravity
driven flows. When there is flow, the pressure drop in the tube due to friction should also be
considered. This will result in raising the bottle a little higher to overcome pressure drop.
EXAMPLE 3–99
A gasoline line is connected to a pressure gage through a double-U manometer,
as shown in Fig. P3–124. If the reading of the pressure gage is 370 kPa,
determine the gage pressure of the gasoline line.
Assumptions 1 All the liquids are
incompressible. 2 The effect of air column
on pressure is negligible.
Properties The specific gravities of oil,
mercury, and gasoline are given to be 0.79,
13.6, and 0.70, respectively. We take the
density of water to be ρw = 1000 kg/m3.
Analysis Starting with the pressure
indicated by the pressure gage and moving
along the tube by adding (as we go down) or
subtracting (as we go up) the ghρ terms until
we reach the gasoline pipe, and setting the
result equal to Pgasoline gives

Rearranging,
Substituting,
Therefore, the pressure in the gasoline pipe is 15.4 kPa lower than the pressure
reading of the pressure gage.
Discussion Note that sometimes the use of specific gravity offers great
convenience in the solution of problems that involve several fluids.

EXAMPLE 3–100
Repeat Prob. 3–124 for a pressure gage reading of 240 kPa.
Assumptions 1 All the liquids are incompressible. 2 The effect of air column on pressure is
negligible.
Properties The specific gravities of oil, mercury, and gasoline are given to be 0.79, 13.6,
and 0.70, respectively. We take the density of water to be ρw = 1000 kg/m3.
Analysis Starting with the pressure indicated by the pressure gage and moving along the
tube by adding (as we go down) or subtracting (as we go up) the ghρ terms until we reach
the gasoline pipe, and setting the result equal to Pgasoline gives
Rearranging,
Substituting,
Therefore, the pressure in the gasoline pipe is 15.4 kPa lower than the pressure reading of
the pressure gage.
Discussion Note that sometimes the use of specific gravity offers great convenience in the
solution of problems that involve several fluids.
EXAMPLE 3–101
The pressure of water flowing through a pipe is measured by the arrangement
shown in Fig. P3–127. For the values given, calculate the pressure in the pipe.

negligible.
Properties The specific gravity of gage fluid is given to be 2.4. We take the standard density
of water to be ρw = 1000 kg/m3.
Analysis Starting with the pressure indicated by the pressure gage and moving along the
tube by adding (as we go down) or subtracting (as we go up) the ρgh terms until we reach
the water pipe, and setting the result equal to Pwater give
Rearranging,
Noting that sinθ = 8/12 = 0,6667 and substituting,
Therefore, the pressure in the gasoline pipe is 3.6 kPa over the reading of the pressure
gage.
Discussion Note that even without a manometer, the reading of a pressure gage can be in
error if it is not placed at the same level as the pipe when the fluid is a liquid.
EXAMPLE 3–102
Consider a U-tube filled with mercury except the 18-cm-high portion at the top, as
shown in Fig. P3–128. The diameter of the right arm of the U-tube is D = 2 cm,
and the diameter of the left arm is twice that. Oil with a specific gravity of 2.72 is
poured into the left arm, forcing some mercury from the left arm into the right one.
Determine the maximum amount of oil that can be added into the left arm.
Answer: 0.256 L
Assumptions 1 Both liquids are incompressible.
2 The U-tube is perfectly vertical.
Properties The specific gravities are given to be
2.72 for oil and 13.6 for mercury.
Analysis Initially, the mercury levels in both tubes
are the same. When oil is poured into the left arm,
it will push the mercury in the left down, which will
cause the mercury level in the right arm to rise.
Noting that the volume of mercury is constant, the
decrease in the mercury volume in left column
must be equal to the increase in the mercury
volume in the right arm. Therefore, if the drop in
mercury level in the left arm is x, the rise in the
mercury level in the right arm h corresponding to
a drop of x in the left arm is
The pressures at points A and B are equal PA = PB and thus
Solving for x and substituting,
Therefore, the maximum amount of oil

that can be added into the left arm is
Discussion Note that the fluid levels in the two arms of a U-tube can be different
when two different fluids are involved.
EXAMPLE 3–103
A teapot with a brewer at the top is used to brew tea, as shown in Fig. P3–129.
The brewer may partially block the vapor from escaping, causing the pressure in
the teapot to rise and an overflow from the service tube to occur. Disregarding
thermal expansion and the variation in the amount of water in the service tube to
be negligible relative to the amount of water in the teapot, determine the
maximum coldwater height that would not cause an overflow at gage pressures
of up to 0.32 kPa for the vapor.
Assumptions 1 Water is incompressible. 2
Thermal expansion and the amount of water in
the service tube are negligible. 3 The cold water
temperature is 20°C.
Properties The density of water at 20°C is ρw =
998.0 kg/m3.
Analysis From geometric considerations, the
vertical distance between the bottom of the
teapot and the tip of the service tube is

This would be the maximum water height if there were no pressure build-up inside
by the steam. The steam pressure inside the teapot above the atmospheric
pressure must be balanced by the water column inside the service tube,
or,
Therefore, the water level inside the teapot must be 3.3 cm below the tip of the
service tube. Then the maximum initial water height inside the teapot to avoid
overflow becomes
Discussion We can obtain the same result formally by starting with the vapor
pressure in the teapot and moving along the service tube by adding (as we go
down) or subtracting (as we go up) the ρgh terms until we reach the atmosphere,
and setting the result equal to Patm:

EXAMPLE 3–104
Repeat Prob. 3–129 by taking the thermal expansion of water into consideration
as it is heated from 20°C to the boiling temperature of 100°C.
Assumptions 1 The amount of water in the service tube is negligible. 3 The cold
water temperature is 20°C.
Properties The density of water is ρw = 998.0 kg/m3 at 20°C, and ρw = 957.9 kg/m3
at 100°C
Analysis From geometric considerations, the vertical distance between the
bottom of the teapot and the tip of the service tube is
This would be the maximum water height if there were no pressure build-up inside
by the steam. The steam pressure inside the teapot above the atmospheric
pressure must be balanced by the water column inside the service tube,
or,

Therefore, the water level inside the teapot must be 3.4 cm below the tip of the
service tube. Then the height of hot water inside the teapot to avoid overflow
becomes
The specific volume of water is 1/998 m3/kg at 20°C and 1/957.9 m3/kg at 100°C.
Then the percent drop in the volume of water as it cools from 100°C to 20°C is
Volume is proportional to water height, and to allow for thermal expansion, the
volume of cold water should be 4% less. Therefore, the maximum initial water
height to avoid overflow should be
Discussion Note that the effect of thermal expansion can be quite significant.
EXAMPLE 3–105
It is well known that the temperature of the atmosphere varies with altitude. In the
troposphere, which extends to an altitude of 11 km, for example, the variation of
temperature can be approximated by T = T0 – βz, where T0 is the temperature at
sea level, which can be taken to be 288.15 K, and β = 0.0065 K/m. The
gravitational acceleration also changes with altitude as g(z)= g0/(1 + z/6,370,320)2
where g0 = 9.807 m/s2 and z is the elevation from sea level in m. Obtain a relation
for the variation of pressure in the troposphere (a) by ignoring and (b) by
considering the variation of g with altitude.
Assumptions The air in the troposphere behaves as an ideal gas.
Analysis (a) Pressure change across a differential fluid layer of thickness dz in
the vertical z direction is
Separating variables and integrating from z = 0 where P = P0 to z = z where P =

P,
Performing the integrations.
Rearranging, the desired relation for atmospheric pressure for the case of
constant g becomes
(b) When the variation of g with altitude is considered, the procedure remains the
same but the expressions become more complicated,
Separating variables and integrating from z = 0 where P = P0 to z = z where P =

P,

Performing the integrations,
where R = 287 J/kg⋅K = 287 m2/s2⋅K is the gas constant of air. After some
manipulations, we obtain
where T0 = 288.15 K, β = 0.0065 K/m, g0 = 9.807 m/s2, k = 1/6,370,320 m-1, and z

is the elevation in m..

EXAMPLE 3–106
The variation of pressure with density in a thick gas layer is given by P = Cρn,
where C and n are constants. Noting that the pressure change across a
differential fluid layer of thickness dz in the vertical z-direction is given as dP = -ρg
dz, obtain a relation for pressure as a function of elevation z. Take the pressure
and density at z = 0 to be P0 and ρ0, respectively.
Assumptions The property relation P = Cρn is valid over the entire region
considered.
Analysis The pressure change across a differential fluid layer of thickness dz in
the vertical z direction is given as,
Also, the relation P = Cρn can be expressed as C = P / ρn = P0 / pn0, and thus
Substituting,

Separating variables and integrating from z = 0 where P = P0 = Cρn0 to z = z
where P = P,
Performing the integrations.
Solving for P,
which is the desired relation.

Discussion The final result could be expressed in various forms. The form given
is very convenient for calculations as it facilitates unit cancellations and reduces
the chance of error.
EXAMPLE 3–107
Pressure transducers are commonly used
to measure pressure by generating analog
signals usually in the range of 4 mA to 20
mA or 0 V-dc to 10 V-dc in response to
applied pressure. The system whose
schematic is shown in Fig. P3–133 can be
used to calibrate pressure transducers. A
rigid container is filled with pressurized air,
and pressure is measured by the
manometer attached. A valve is used to
regulate the pressure in the container.
Both the pressure and the electric signal
are measured simultaneously for various
settings, and the results are tabulated. For
the given set of measurements, obtain the
calibration curve in the form of P = aI + b,
where a and b are constants, and
calculate the pressure that corresponds to
a signal of 10 mA.

Assumptions Mercury is an incompressible liquid.
Properties The specific gravity of mercury is given to be 13.56, and thus its
density is 13,560 kg/m3.
Analysis For a given differential height, the pressure can be calculated from
For Δh = 28.0 mm = 0.0280 m, for example,
Repeating the calculations and tabulating, we have
A plot of P versus I is given below. It is clear that the pressure varies linearly with
the current, and using EES, the best curve fit is obtained to be

EXAMPLE 3–108
A system is equipped with two pressure gages and a manometer, as shown in Fig.
P3–134. For Δh = 8 cm, determine the pressure difference ΔP = P2 – P1.

negligible.
Properties The specific gravities are given tone 2.67 for the gage fluid and 0.87 for oil. We
take the standard density of water to be ρw = 1000 kg/m3.
Analysis Starting with the pressure indicated by the pressure gage 2 and moving along the
tube by adding (as we go down) or subtracting (as we go up) the ρgh terms and ignoring the
air spaces until we reach the pressure gage 1, and setting the result equal to P1 give
Rearranging,
Substituting,
Therefore, the pressure reading of the left gage is 3.45 kPa lower than that of the right gage.
Discussion The negative pressure difference indicates that the pressure differential across
the oil level is greater than the pressure differential corresponding to the differential height of
the manometer fluid.
EXAMPLE 3–109
An oil pipeline and a 1.3-m3 rigid air tank are connected to each other by a
manometer, as shown in Fig. P3–135. If the tank contains 15 kg of air at 80°C,
determine (a) the absolute pressure in the pipeline and (b) the change in Δh when
the temperature in the tank drops to 20°C. Assume the pressure in the oil pipeline
to remain constant, and the air volume in the manometer to be negligible relative
to the volume of the tank.

Assumptions 1 All the liquids are incompressible. 2 The effect of air column on
pressure is negligible. 3 The air volume in the manometer is negligible compared
with the volume of the tank.
Properties The specific gravities are given to be 2.68 for oil and 13.6 for mercury.
We take the standard density of water to be ρw = 1000 kg/m3. The gas constant of
air is 0.287 kPa⋅m3/kg⋅K.
Analysis (a) Starting with the oil pipe and moving along the tube by adding (as
we go down) or subtracting (as we go up) the ρgh terms until we reach the air
tank, and setting the result equal to Pair give
The absolute pressure in the air tank is determined from the ideal-gas relation PV
= mRT to be
Then the absolute pressure in the oil pipe becomes

(b) The pressure in the air tank when the temperature drops to 20°C becomes
When the mercury level in the left arm drops a distance x, the rise in the mercury
level in the right arm y becomes
and the mercury fluid height will change by x + 9x sin50° or 7.894x. Then,
Substituting,
It gives
Therefore, the oil-mercury interface will drop 19.4 cm as a result of the

temperature drop of air.
Discussion Note that the pressure in constant-volume gas chambers is very
sensitive to temperature changes.
EXAMPLE 3–110
The density of a floating body can be determined by tying weights to the body until
both the body and the weights are completely submerged, and then weighing
them separately in air. Consider a wood log that weighs 1540 N in air. If it takes 34
kg of lead (ρ = 11,300 kg/m3) to completely sink the log and the lead in water,
determine the average density of the log.
Answer: 835 kg/m3
Properties The density of lead weights is given to be 11,300 kg/m3. We take the
density of water to be 1000 kg/m3.
Analysis The weight of a body is equal to the buoyant force when the body is
floating in a fluid while being completely submerged in it (a consequence of
vertical force balance from static equilibrium). In this case the average density of
the body must be equal to the density of the fluid since
Therefore,

where
Substituting, the volume and density of the log are determined to be
Discussion Note that the log must be completely submerged for this analysis to
be valid. Ideally, the lead weights must also be completely submerged, but this is
not very critical because of the small volume of the lead weights.

EXAMPLE 3–111
The 200-kg, 5-m-wide rectangular gate shown in Fig. P3–137 is hinged at B and
leans against the floor at A making an angle of 45° with the horizontal. The gate is
to be opened from its lower edge by applying a normal force at its center.
Determine the minimum force F required to open the water gate.
Answer: 520 kN
Assumptions 1 The atmospheric

pressure acts on both sides of the
gate, and thus it can be ignored in
calculations for convenience. 2
Friction at the hinge is negligible.
water to be 1000 kg/m3 throughout.
Analysis The length of the gate and
the distance of the upper edge of the
gate (point B) from the free surface in
the plane of the gate are

The average pressure on a surface is the pressure at the centroid (midpoint) of the surface,
and multiplying it by the plate area gives the resultant hydrostatic on the surface,
The distance of the pressure center from the free surface of water along the plane of the
gate is
The distance of the pressure center from the hinge at point B

is
Taking the moment about point B and setting it equal to zero
gives
Taking the moment about point B and setting it equal to zero

gives
Discussion The applied force is inversely proportional to the distance of the point of
application from the hinge, and the required force can be reduced by applying the force at a
lower point on the gate. PROPRIETARY
EXAMPLE 3–112
Repeat Prob. 3–137 for a water height of 1.2 m above the hinge at B.
Assumptions 1 The atmospheric pressure acts on both sides of the gate, and
thus it can be ignored in calculations for convenience. 2 Friction at the hinge is
negligible.
Analysis The length of the gate and the distance of the upper edge of the gate
(point B) from the free surface in the plane of the gate are
The average pressure on a surface is the pressure at the centroid (midpoint) of

the surface, and multiplying it by the plate area gives the resultant hydrostatic on
the surface,
The distance of the pressure center from the free surface of water along the plane
of the gate is

The distance of the pressure center from the hinge at point B is
Taking the moment about point B and setting it equal

to zero gives
Solving for F and substituting, the required force is

determined to be
Discussion The applied force is inversely proportional to the distance of the point
of application from the hinge, and the required force can be reduced by applying
the force at a lower point on the gate.

EXAMPLE 3–113
3-m-high, 6-m-wide rectangular gate is hinged at the top edge at A and is
restrained by a fixed ridge at B. Determine the hydrostatic force exerted on the
gate by the 5-m-high water and the location of the pressure center.
The

Assumptions The atmospheric pressure acts on both sides of the gate, and thus
Analysis The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and multiplying it by the plate area gives the resultant
hydrostatic force on the gate,
The vertical distance of the pressure center from the free

surface of water is

EXAMPLE 3–114
Repeat Prob. 3–139 for a total water height of 2 m.
Assumptions The atmospheric pressure acts on both sides of the gate, and thus
Analysis The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and multiplying it by the wetted plate area gives the
resultant hydrostatic force on the gate,
The vertical distance of the pressure center from the free

surface of water is

EXAMPLE 3–115
A 50-ton, 6-m-diameter hemispherical dome on a level surface is filled with water,
as shown in Fig. P3–142. Someone claims that he can lift this dome by making
use of Pascal’s law by attaching a long tube to the top and filling it with water.
Determine the required height of water in the tube to lift the dome. Disregard the
weight of the tube and the water in it.
Answer: 0.77 m
Assumptions 1 The atmospheric pressure acts on
both sides of the dome, and thus it can be ignored
in calculations for convenience. 2 The weight of the
tube and the water in it is negligible.
Properties We take the density of water to be 1000
kg/m3 throughout.
Analysis We take the dome and the water in it as
the system. When the dome is about to rise, the
reaction force between the dome and the ground
becomes zero. Then the free body diagram of this
system involves the weights of the dome and the
water, balanced by the hydrostatic pressure force
from below. Setting these forces equal to each other
gives

Solving for h gives
Substituting,
Therefore, this dome can be lifted by attaching a tube which is 77 cm long.
Discussion Note that the water pressure in the dome can be changed greatly by
a small amount of water in the vertical tube.

EXAMPLE 3–116
The water in a 25-m-deep reservoir is kept inside by a 150-m-wide wall whose
cross section is an equilateral triangle, as shown in Fig. P3–143. Determine (a)
the total force (hydrostatic + atmospheric) acting on the inner surface of the wall
and its line of action and (b) the magnitude of the horizontal component of this
force. Take Patm = 100 kPa.
Assumptions 1 The atmospheric

pressure acts on both sides of the
gate, and thus it can be ignored in
calculations for convenience. 2
Friction at the hinge is negligible.
water to be 1000 kg/m3
throughout.
Analysis The length of the wall
surface underwater is 3-108

The average pressure on a surface is the pressure at the centroid (midpoint) of the surface,
and multiplying it by the plate area gives the resultant hydrostatic force on the surface,
Noting that
the distance of the pressure center from the free surface of

water along the wall surface is
The magnitude of the horizontal component of the hydrostatic force is

simply FRsin θ,
Discussion The atmospheric pressure is usually ignored in the

analysis for convenience since it acts on both sides of the walls.
EXAMPLE 3–117
A U-tube contains water in the right arm, and another liquid in the left arm. It is
observed that when the U-tube rotates at 30 rpm about an axis that is 15 cm from
the right arm and 5 cm from the left arm, the liquid levels in both arms become the
same. Determine the density of the fluid in the left arm.
Assumptions 1 Both the fluid and the water are

incompressible fluids. 2 The two fluids meet at the axis
of rotation, and thus there is only water to the right of the
axis of rotation.
Properties We take the density of water to be 1000
kg/m3.
Analysis The pressure difference between two points 1
and 2 in an incompressible fluid rotating in rigid body
motion (the same fluid) is given by

Pressure at point 2 is the same for both fluids, so are the pressures at points 1
and 1* (P1 = P1* = Patm). Therefore, P2 – P1 is the same for both fluids. Noting that
z2 – z1 = h for both fluids and expressing P2 – P1 for each fluid,
Setting them equal to each other and solving for ρƒ

gives
Discussion Note that this device can be used to determine relative densities,
though it wouldn’t be a very practical.

EXAMPLE 3–118
A 1-m-diameter, 2-m-high vertical cylinder is completely filled with gasoline whose
density is 740 kg/m3. The tank is now rotated about its vertical axis at a rate of 90
rpm, while being accelerated upward at 5 m/s2. Determine (a) the difference
between the pressures at the centers of the bottom and top surfaces and (b) the
difference between the pressures at the center and the edge of the bottom
surface.

Assumptions 1 The increase in the rotational speed is very slow so that the
liquid in the container always acts as a rigid body. 2 Gasoline is an
incompressible substance.
Properties The density of the gasoline is given to be 740 kg/m3.
Analysis The pressure difference between two points 1 and 2 in an
incompressible fluid rotating in rigid body motion is given by P2 – P1 = ρω2/2 (r22 –
r21) – ρg(z2 – z1). The effect of linear acceleration in the vertical direction is
accounted for by replacing g + ɑz. Then,

(a) Taking points 1 and 2 to be the centers of the bottom and top surfaces, respectively, we
have r1 = r2 =0 and z2 – z1 = h = 3m . Then,
(b) Taking points 1 and 2 to be the center and edge of the bottom surface, respectively, we
have r1 =0 , r2 = R, and z2 = z1 = 0. Then,
Discussion Note that the rotation of the tank does not affect the pressure difference along
the axis of the tank. Likewise, the vertical acceleration does not affect the pressure
difference between the edge and the center of the bottom surface (or any other horizontal
plane).
EXAMPLE 3–119
A 5-m-long, 4-m-high tank contains 2.5-m-deep water when not in motion and is
open to the atmosphere through a vent in the middle. The tank is now accelerated
to the right on a level surface at 2 m/s2. Determine the maximum pressure in the
tank relative to the atmospheric pressure.
Answer: 29.5 kPa
Assumptions 1 The road is horizontal
during acceleration so that acceleration
has no vertical component (az = 0). 2
Effects of splashing, breaking and driving
over bumps are assumed to be
secondary, and are not considered. 3 The
vent is never blocked, and thus the
minimum pressure is the atmospheric
pressure.
Properties We take the density of water
to be 1000 kg/m3.
Analysis We take the x-axis to be the
direction of motion, the z-axis to be the
upward vertical direction. The tangent of
the angle the free surface makes with the
horizontal is
The maximum vertical rise of the free surface occurs at the back of the tank, and
the vertical midsection experiences no rise or drop during acceleration. Then the
maximum vertical rise at the back of the tank relative to the neutral midplane is
which is less than 1.5 m high air

space. Therefore, water never
reaches the ceiling, and the
maximum water height and the
corresponding maximum pressure
are
Discussion It can be shown that the gage pressure at the bottom of the tank
varies from 29.5 kPa at the back of the tank to 24.5 kPa at the midsection and
19.5 kPa at the front of the tank.
EXAMPLE 3–120
An elastic air balloon having a diameter of 30 cm is attached to the base of a
container partially filled with water at + 4°C, as shown in Fig. P3–148. If the
pressure of air above water is gradually increased from 100 kPa to 1.6 MPa, will
the force on the cable change? If so, what is the percent change in the force?
Assume the pressure on the free surface and the diameter of the balloon are
related by P = CDn, where C is a constant and n = -2. The weight of the balloon
and the air in it is negligible. Answer: 98.4 percent
Assumptions 1 The atmospheric pressure acts
on all surfaces, and thus it can be ignored in
calculations for convenience. 2 Water is an
incompressible fluid. 3 The weight of the balloon
and the air in it is negligible.
Properties We take the density of water to be
1000 kg/m3.
Analysis The tension force on the cable holding
the balloon is determined from a force balance on
the balloon to be

The buoyancy force acting on the balloon initially is
The buoyancy force acting on the balloon in this case is

Then the percent change in the cable for becomes
Therefore, increasing the tank pressure in this case results in 98.4% reduction in
cable tension.
Discussion We can obtain a relation for the change in cable tension as follows:

EXAMPLE 3–121
The average density of icebergs is about 917 kg/m3. (a) Determine the
percentage of the total volume of an iceberg submerged in seawater of density
1042 kg/m3. (b) Although icebergs are mostly submerged, they are observed to
turn over. Explain how this can happen. (Hint: Consider the temperatures of
icebergs and seawater.)
Assumptions 1 The buoyancy force in air is negligible. 2 The density of iceberg

and seawater are uniform.
Properties The densities of iceberg and seawater are given to be 917 kg/m3 and
1042 kg/m3, respectively.
Analysis (a) The weight of a body floating in a fluid is equal to the buoyant force
acting on it (a consequence of vertical force balance from static equilibrium).
Therefore,

Therefore, 88% of the volume of the iceberg is submerged in this case.
(b) Heat transfer to the iceberg due to the temperature difference between the
seawater and an iceberg causes uneven melting of the irregularly shaped iceberg.
The resulting shift in the center of mass causes turn over.
Discussion Note that the submerged fraction depends on the density of

seawater, and this fraction can different in different seas.

EXAMPLE 3–122
A cylindrical container whose weight is 79 N is inverted and pressed into the
water, as shown in Fig. P3–151. Determine the differential height h of the
manometer and the force F needed to hold the container at the position shown.
Assumptions 1 The
atmospheric pressure acts on
all surfaces, and thus it can
be ignored in calculations for
convenience. 2 The variation
of air pressure inside cylinder
is negligible.
Properties We take the
density of water to be 1000
kg/m3. The density of the
manometer fluid is

Analysis The pressures at point A and B must be the same since they are on the
same horizontal line in the same fluid. Then the gage pressure in the cylinder
becomes
The manometer also indicates the gage pressure in the cylinder. Therefore,
A force balance on the cylinder in the vertical direction yields
Solving for F and substituting,
Discussion We could also solve this problem by considering the atmospheric

pressure, but we would obtain the same result since atmospheric pressure would
cancel out.

Examples 03

Uploaded by

Copyright:

Available Formats

Examples 03

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Examples 03

Uploaded by

Copyright:

Available Formats

Examples

Prof. Dr. Ali PINARBAŞI

Taking their ratio,

(b) The absolute pressure at a depth of 5 m in the other liquid is

Assumptions 1 The weight of the person is distributed uniformly on the imprint

Then the absolute pressure in the tank becomes

Analysis The absolute pressure in the tank is determined from

which is also the distance climbed.

which is also the height of the building.

The pressure exerted on a diver at 30 m below the free

Setting them equal to each other and simplifying,

Assumptions The weight of the piston of the lift is negligible.

Therefore, the pressure in the fresh water pipe is 8.34 kPa

That is, the pressures on both sides of the paper must be

Rearranging and substituting the known values,

Discussion Note that vertical distances are used in manometer analysis.

The equivalent mercury column height is

The resultant hydrostatic force acting on a submerged surface is the resultant of

The horizontal component of the hydrostatic force acting on a curved surface is

The vertical component of the hydrostatic force acting on a curved surface is

The line of action of the force passes through the pressure

Horizontal force on vertical surface:

Taking the moment about point A and setting it equal to

Solving for Fridge and substituting, the reaction force is

Horizontal force on vertical surface:

Solving for T and substituting, the tension in the cable is determined to be

The hydrostatic forces acting on the vertical and horizontal

The distance of the centroid of a triangle from a side is

The hydrostatic force exerted by the mud to the wall is

Setting the hydrostatic and friction forces equal to each

The hydrostatic force exerted by the mud to the wall is

Vertical force on horizontal surface (upward):

The weight of fluid block per 4-m length (downwards):

Solving for Fspring and substituting, the spring force is determined to be

Vertical force on horizontal surface (upward):

Therefore, the net upward vertical force is

Solving for Fspring and substituting, the spring force is determined to be

100 Bölüm 5: KontrolChapter

101 Bölüm 5: KontrolChapter

102 Bölüm 5: KontrolChapter

103 Bölüm 5: KontrolChapter

where h is the height of the submerged portion of the

Setting the relations above equal to each other (since both

Solving for the liquid density and substituting,

Noting that FB = ρwater gV, the volume of the body is determined to be

105 Bölüm 5: KontrolChapter

107 Bölüm 5: KontrolChapter

The cross-sectional of a cube is constant, and thus the

where h is the height of the ice block below the surface.

The buoyancy force acting on the rock is

109 Bölüm 5: KontrolChapter

Discussion This force corresponds to a mass of

110 Bölüm 5: KontrolChapter

111 Bölüm 5: KontrolChapter

Noting that FB = ρwater gV, the volume of the crown

Then the density of the crown becomes

113 Bölüm 5: KontrolChapter

Noting that mass is density times volume, the last relation

Canceling the V and solving for xfat gives the desired