MICRO CONFIGURATIONS AND FUNCTIONS

SUPRA
Supra 4XX Supra 5XX Supra 7XX Supra 8XX Supra 9XX
Supra 4XX Supra 5XX OASIS 150 Supra 7XX OASIS 250 750sw 750sw Nordic Supra 8XX Supra 9XX OASIS 350
Nordic Nordic Nordic Nordic Nordic
MICRO configuration Description
Soft 3.33 3.33 3.33 3.33 3.33 3.33 3.33 3.33 3.33 3.33 3.33 3.33 3.33 3.33 3.33

GLOW TIME DI Engine long glow cycle DI

CNF1: choix(DI/TV)
Indicates to the control which engine is in the system and which glow time should beTV Engine short glow cycle TV TV TV TV TV TV TV TV TV TV TV TV TV TV TV TV
DISCHARGE SENSOR CDT not used OFF OFF OFF OFF OFF OFF
CNF2 : choix (ON/OFF)
Indicates to the control if the DISCHARGE sensor is installed CDT used ON ON ON ON ON ON ON ON ON ON ON
HIGH SETPOINT 30°c (86°F) Max. Set point OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF3 : choix (ON/OFF)
Indicates maximum Set Point allowed 32°c (90°F) Max. Set point ON
HEAT LOCKOUT OVERRIDE (Truck unit) Heat lockout on -12°c (10°F) OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF4 : choix (ON/OFF)
Indicates to the control if the heat lockout is overridden Heat lockout off ON ON ON ON ON ON ON
MOP MOP disabled OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF5 : choix (ON/OFF)
Indicates status of MOP control MOP enabled ON ON ON ON
TRUCK UNIT Trailer unit OFF
CNF6 : choix (ON/OFF)
Indicates to the control if the system has been selected for truck operation Truck unit ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
HIGH SPEED OVERRIDE High speed start OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF7 : choix (ON/OFF)
Indicates to the control if lock in high speed start Low speed start ON
ELECTRIC FAN Belt driven fan OFF
CNF8 : choix (ON/OFF)
Indicates to the control if electric fans are being used Electrical fan motors ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
OUT-OF-RANGE SHUT DOWN Out of range alarm only OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF9 : choix (ON/OFF)
Indicates if main compartment out-of-range alarm shuts unit down after 45min. Out of range alarm and unit shut down ON
TRUCK AUTO-RESTART OPTION No auto restart OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF10 : choix (ON/OFF)
Indicates if diesel restart after AC power loss function is active Auto restart active if FN6=Time start ON
FUNCTIONAL PARAMETERS (KEYPAD) LOCKOUT OPTION Functions normal OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF11 : choix (ON/OFF)
Allow or lockout certain any changes of the functional parameter from keypad Functions locked ON
HP-62 MOP OPTION MOP parameter HP 62 option OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF12 : choix (ON/OFF)
Use either normal or HP-62 MOP parameters Active ON
HEAT ONLY UNIT OPERATION OPTION Normal cool / heat / defrost operation OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF13 : choix (ON/OFF)
Converts unit to a "Heat only" unit Heat only operation (Solara) ON
INVERTABLE MULTI TEMP Not active OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF14 : choix (ON/OFF)
Indicates to the control if reversible multi temp control is active Reversible multi-temp active ON
DIESEL / ELECTRIC STANDBY (Truck unit) Truck with Diesel & electrical standby OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF15 : choix (ON/OFF)
Indicates to the control if the truck is diesel only Truck diesel only ON
SHUNT DOWN WITH ALTERNATOR AUX ALARM Alt aux alarm only OFF
CNF16 : choix (ON/OFF)
Indicates if alternator AUX alarm shuts unit down in diesel mode Alt aux alarm & unit shut down ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
ULTRA FREEZE 1 OPERATION Disable Ultra freeze 1 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF 17 : choix (ON/OFF)
Indicates to the control if UFZ1 operation can run Enable Ultra freeze 1 ON
LOW REFRIGERANT TEST Disable low refrigerrant test OFF
CNF 18 : choix (ON/OFF)
Indicates to the control if low refrigerant test is enable Enable low refrigerrant test ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON
SIROCCO UNIT Supra unit OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF 19 : choix (ON/OFF)
Indicates if the unit is Sirocco unit Sirocco unit ON
UNITS SELECTION LOCK OPTION Metric unit or english metric is not locked OFF
CNF 20 : choix (ON/OFF)
Indicates to the control if the units functional parameter is locked Unit selection is locked ON ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC
FROZEN MODE PRIORITY LOGIC OPTION Frozen priority not active OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF 21 : choix (ON/OFF)
Enables frozen priority logic Active ON
HOT GAS VALVES DRIVE Together OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF 22 : choix (ON/OFF)
Indicates if the hot gas valves are driven together or separately Separately ON
SET POINT LOCK Set Point is not locked OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
CNF 23 : choix (ON/OFF)
Indicates if the change of the Set Point is locked Set Point is locked ON
WT SENSOR ALARM WT sensor alarm only OFF
CNF 24 : choix (ON/OFF)
Indicates if WT sensor alarm shuts unit down WT sensor alarm & unit shut down ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON

CNF 25 to CNF 32 : choix (ON/OFF) Not used OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF

Micro parameters
FN0 Defrost setting : 1,5;3;6;12h 3h 3h 3h 3h 3h 6h 6h 6h 6h 6h 6h 6h 3h 3h 3h
FN1 ON/OFF Air On = high/Off=Norm OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air
FN2 Off time choice : 10;20;30;45;90mn 20 mn 20 mn 20 mn 20 mn 20 mn 20 mn 20 mn 20 mn 20 mn 20 mn 20 mn 20 mn 20 mn 20 mn 20 mn
FN3 On time choice 4;7 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn
FN4 A/B PROBE choice A=Rem/B=Sup A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe A=Rem probe
FN5 F/C degree choix : F or C deg C deg C deg C deg C deg C deg C deg C deg C deg C deg C deg C deg C deg C deg C deg C
FN6 On=time start/ Off=temp start OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt
FN7 MOP choice : STD=0/-=-5/+=+4 STD=0 STD=0 STD=0 STD=0 STD=0 STD=0 STD=0 STD=0 STD=0 STD=0 STD=0 STD=0 STD=0 STD=0 STD=0
FN8 2SET Set point adjustment 2CP Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans
FN9 3SET Set point adjustment 3CP Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans Sans
FN10 Start Op choice : on=Auto/off=Man On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP
FN11 T range choix A=2, B=3, C=4 Dreg C C C C C C C C C C C C C C C C
Affichage display T Range choix : CODES OU ENGLISH English English English English English English English English English English English English English English English
Manuel glow override choice NORM / ADD Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow
Alarm reset CLR/RST CLR CLR CLR CLR CLR CLR CLR CLR CLR CLR CLR CLR CLR CLR CLR

Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

SUPRA MT
Description R90U R90 S750MT OASIS 250MT S850MT 950MT 950UMT
MICRO configuration
Soft 4,06 4,06 4,06 4,06 4,06 4,06 4,06

DI DI Engine long glow cycle

CNF1: choix(DI/TV)
TV TV Engine short glow cycle TV TV TV TV TV TV TV
OFF CDT not used OFF
CNF2 : choix (ON/OFF)
ON CDT used ON ON ON ON ON ON
OFF 30°c (86°F) Max. Set point OFF OFF OFF OFF OFF OFF OFF
CNF3 : choix (ON/OFF)
ON 32°c (90°F) Max. Set point
OFF Heat lockout on -12°c (10°F) OFF OFF OFF OFF OFF OFF OFF
CNF4 : choix (ON/OFF)
ON Heat lockout off (trailor units)
OFF Frozen priority not active
CNF5 : choix (ON/OFF)
ON Active ON ON ON ON ON ON ON
OFF Trailer unit
CNF6 : choix (ON/OFF)
ON Truck unit ON ON ON ON ON ON ON
OFF Low speed start OFF OFF OFF OFF OFF OFF OFF
CNF7 : choix (ON/OFF)
ON High speed start
OFF Belt driven fan
CNF8 : choix (ON/OFF)
ON Electrical fan motors ON ON ON ON ON ON ON
OFF Out of range alarm not shut down OFF OFF OFF OFF OFF OFF OFF
CNF9 : choix (ON/OFF)
ON Out of range alarm and unit shut down
OFF No auto restart OFF OFF OFF OFF OFF OFF OFF
CNF10 : choix (ON/OFF)
ON Auto restart active if FN5=Time start
OFF Functions normal OFF OFF OFF OFF OFF OFF OFF
CNF11 : choix (ON/OFF)
ON Functions locked
OFF Low Oil Level Alarm OFF OFF OFF OFF OFF OFF OFF
CNF12 : choix (ON/OFF)
ON Active
OFF Disable low refrigerant test
CNF13 : choix (ON/OFF)
ON Enable low refrigerant test ON ON ON ON ON ON ON
OFF Not active OFF OFF OFF OFF OFF OFF OFF
CNF14 : choix (ON/OFF)
ON
OFF Not active OFF OFF OFF OFF OFF OFF OFF
CNF15 : choix (ON/OFF)
ON
OFF Alt aux alarm only
CNF16 : choix (ON/OFF)
ON Alt aux alarm & unit shut down ON ON ON ON ON ON ON
OFF OFF OFF OFF OFF OFF OFF OFF
CNF17 to CNF32 : choix (ON/OFF)
ON

Micro parameters
FN0 Defrost setting : 1,5;3;6;12h 3H 3H 3H 3H 3H 3H 3H
FN1 ON/OFF Air On = high/Off=Norm OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air
FN2 Off time choice : 10;20;30;45;90mn 20 mn 20 mn 10 mn 10 mn 10 mn 10 mn 20 mn
FN3 On time choice 4;7 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn 7 mn
FN4 F/C degree choix : F or C Deg C Deg C Deg C Deg C Deg C Deg C Deg C
FN5 On=time start/ Off=temp start OFF=temp strt OFF=temp strt OFF=temp strt OFF=temp strt OFF=temp strt OFF=temp strt OFF=temp strt
FN6 MOP choice : STD=0/-=-5/+=+4 STD=0 STD=0 STD=0 STD=0 -5 STD=0 STD=0
FN7 Start Op choice : on=Auto/off=Man ON=Auto OP ON=Auto OP ON=Auto OP ON=Auto OP ON=Auto OP ON=Auto OP ON=Auto OP
FN8 T range choix A=2, B=3, C=4 Dreg C C C C C C C C
Affichage display CODES OR ENGLISH Display English English English English English English English
Manuel glow override choice NORM / ADD Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow
Alarm reset CLR/RST CLR CLR CLR CLR CLR CLR CLR

Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

UNDERMOUNT
Supra 944U Supra 988U Supra 950U Supra 850U
MICRO configuration Description
Soft 3.33 3.33 3.33 3.33

GLOW TIME DI Engine long glow cycle DI

CNF1: choix(DI/TV)
Indicates to the control which engine is in the system and which glow time should be TV Engine short glow cycle TV TV TV TV TV
DISCHARGE SENSOR CDT not used OFF OFF
CNF2 : choix (ON/OFF)
Indicates to the control if the DISCHARGE sensor is installed CDT used ON ON ON ON
HIGH SETPOINT 30°c (86°F) Max. Set point OFF OFF OFF OFF OFF
CNF3 : choix (ON/OFF)
Indicates maximum Set Point allowed 32°c (90°F) Max. Set point ON
HEAT LOCKOUT OVERRIDE (Truck unit) Heat lockout on -12°c (10°F) OFF OFF OFF OFF OFF
CNF4 : choix (ON/OFF)
Indicates to the control if the heat lockout is overridden Heat lockout off ON
MOP MOP disabled OFF OFF
CNF5 : choix (ON/OFF)
Indicates status of MOP control MOP enabled ON ON ON ON
TRUCK UNIT Trailer unit OFF
CNF6 : choix (ON/OFF)
Indicates to the control if the system has been selected for truck operation Truck unit ON ON ON ON ON
HIGH SPEED OVERRIDE High speed start OFF OFF OFF OFF OFF
CNF7 : choix (ON/OFF)
Indicates to the control if lock in high speed start Low speed start ON
ELECTRIC FAN Belt driven fan OFF
CNF8 : choix (ON/OFF)
Indicates to the control if electric fans are being used Electrical fan motors ON ON ON ON ON
OUT-OF-RANGE SHUT DOWN Out of range alarm only OFF OFF OFF OFF OFF
CNF9 : choix (ON/OFF)
Indicates if main compartment out-of-range alarm shuts unit down after 45min. Out of range alarm and unit shut down ON
TRUCK AUTO-RESTART OPTION No auto restart OFF OFF OFF OFF OFF
CNF10 : choix (ON/OFF)
Indicates if diesel restart after AC power loss function is active Auto restart active if FN6=Time start ON
FUNCTIONAL PARAMETERS (KEYPAD) LOCKOUT OPTION Functions normal OFF OFF OFF OFF OFF
CNF11 : choix (ON/OFF)
Allow or lockout certain any changes of the functional parameter from keypad Functions locked ON
HP-62 MOP OPTION MOP parameter HP 62 option OFF OFF OFF OFF OFF
CNF12 : choix (ON/OFF)
Use either normal or HP-62 MOP parameters Active ON
HEAT ONLY UNIT OPERATION OPTION Normal cool / heat / defrost operation OFF OFF OFF OFF OFF
CNF13 : choix (ON/OFF)
Converts unit to a "Heat only" unit Heat only operation (Solara) ON
INVERTABLE MULTI TEMP Not active OFF OFF OFF OFF OFF
CNF14 : choix (ON/OFF)
Indicates to the control if reversible multi temp control is active Reversible multi-temp active ON
DIESEL / ELECTRIC STANDBY (Truck unit) Truck with Diesel & electrical standby OFF OFF OFF OFF OFF
CNF15 : choix (ON/OFF)
Indicates to the control if the truck is diesel only Truck diesel only ON
SHUNT DOWN WITH ALTERNATOR AUX ALARM Alt aux alarm only OFF
CNF16 : choix (ON/OFF)
Indicates if alternator AUX alarm shuts unit down in diesel mode Alt aux alarm & unit shut down ON ON ON ON ON
ULTRA FREEZE 1 OPERATION Disable Ultra freeze 1 OFF OFF OFF OFF OFF
CNF 17 : choix (ON/OFF)
Indicates to the control if UFZ1 operation can run Enable Ultra freeze 1 ON
LOW REFRIGERANT TEST Disable low refrigerrant test OFF
CNF18 : choix (ON/OFF)
Indicates to the control if low refrigerant test is enable Enable low refrigerrant test ON ON ON ON ON
SIROCCO UNIT Supra unit OFF OFF OFF OFF OFF
CNF19 : choix (ON/OFF)
Indicates if the unit is Sirocco unit Sirocco unit ON
UNITS SELECTION LOCK OPTION Metric unit or english metric is not locked OFF
CNF 20 : choix (ON/OFF)
Indicates to the control if the units functional parameter is locked Unit selection is locked ON ON METRIC ON METRIC ON METRIC ON METRIC
FROZEN MODE PRIORITY LOGIC OPTION Frozen priority not active OFF OFF OFF OFF OFF
CNF 21 : choix (ON/OFF)
Enables frozen priority logic Active ON
HOT GAS VALVES DRIVE Together OFF OFF OFF OFF OFF
CNF 22 : choix (ON/OFF)
Indicates if the hot gas valves are driven together or separately Separately ON
SET POINT LOCK Set Point is not locked OFF OFF OFF OFF OFF
CNF 23 : choix (ON/OFF)
Indicates if the change of the Set Point is locked Set Point is locked ON
WT SENSOR ALARM (Truck unit) WT sensor alarm only OFF
CNF 24 : choix (ON/OFF)
Indicates if WT sensor alarm shuts unit down WT sensor alarm & unit shut down ON ON ON ON ON

CNF 25 to CNF 32 : choix (ON/OFF) OFF Not used OFF OFF OFF OFF

Micro parameters
FN0 Defrost setting : 1,5;3;6;12h 3h 3h 3h 6h
FN1 ON/OFF Air On = high/Off=Norm OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air
FN2 Off time choice : 10;20;30;45;90mn 20 mn 20 mn 20 mn 20 mn
FN3 On time choice 4;7 7 mn 7 mn 7 mn 7 mn
FN4 A/B PROBE choice A=Rem/B=Sup A=Rem probe A=Rem probe A=Rem probe A=Rem probe
FN5 F/C degree choix : F or C deg C deg C deg C deg C
FN6 On=time start/ Off=temp start OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt
FN7 MOP choice : STD=0/-=-5/+=+4 STD=0 STD=0 STD=0 STD=0
FN8 2SET Set point adjustment 2CP Sans Sans Sans Sans
FN9 3SET Set point adjustment 3CP Sans Sans Sans Sans
FN10 Start Op choice : on=Auto/off=Man On = Auto OP On = Auto OP On = Auto OP On = Auto OP
FN11 T range choix A=2, B=3, C=4 Dreg C C C C C
Affichage display T Range choix : CODES OU ENGLISH English English English English
Manuel glow override choice NORM / ADD Norm Glow Norm Glow Norm Glow Norm Glow
Alarm reset CLR/RST CLR CLR CLR CLR Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

MAXIMA
Maxima 1300 Maxima 1300 MT Maxima 1000 Maxima 1200 Maxima 1200 MT
MICRO configuration Description
Soft 3.33 3.33 3.33 3.33 3.33

GLOW TIME DI Engine long glow cycle DI

CNF1: choix(DI/TV)
Indicates to the control which engine is in the system and which glow time should be TV Engine short glow cycle TV TV TV TV TV TV

DISCHARGE SENSOR CDT not used OFF OFF OFF OFF OFF OFF
CNF2 : choix (ON/OFF)
Indicates to the control if the DISCHARGE sensor is installed CDT used ON

HIGH SETPOINT 30°c (86°F) Max. Set point OFF OFF OFF OFF OFF OFF
CNF3 : choix (ON/OFF)
Indicates maximum Set Point allowed 32°c (90°F) Max. Set point ON

HEAT LOCKOUT OVERRIDE (Maxima MT Only) Overide not enabled OFF OFF OFF OFF
CNF4 : choix (ON/OFF)
Indicates to the control if the heat lockout is overridden Override Enabled ON ON ON

MOP MOP disabled OFF OFF OFF OFF OFF OFF

CNF5 : choix (ON/OFF)
Indicates status of MOP control MOP enabled ON

TRUCK UNIT Trailer unit OFF OFF OFF OFF OFF OFF
CNF6 : choix (ON/OFF)
Indicates to the control if the system has been selected for truck operation Truck unit ON

HIGH SPEED OVERRIDE Logic disabled OFF OFF OFF OFF OFF OFF
CNF7 : choix (ON/OFF)
Indicates to the control if the low speed coolant check logic is enabled Logic enabled ON

ELECTRIC FAN Belt driven fan OFF OFF OFF OFF OFF OFF
CNF8 : choix (ON/OFF)
Indicates to the control if electric fans are being used Electrical fan motors ON

OUT-OF-RANGE SHUT DOWN Out of range alarm only OFF OFF OFF OFF OFF OFF
CNF9 : choix (ON/OFF)
Indicates if main compartment out-of-range alarm shuts unit down after 45min. Out of range alarm and unit shut down ON

NOT ASSIGNED FOR TRAILER Not used OFF OFF OFF OFF OFF OFF
CNF10 : choix (ON/OFF)
Not used ON

FUNCTIONAL PARAMETERS (KEYPAD) LOCKOUT OPTION Functions normal OFF OFF OFF OFF OFF OFF
CNF11 : choix (ON/OFF)
Allow or lockout certain any changes of the functional parameter from keypad Functions locked ON

HP-62 MOP OPTION MOP parameter HP 62 option OFF OFF OFF OFF OFF OFF
CNF12 : choix (ON/OFF)
Use either normal or HP-62 MOP parameters Active ON

HEAT ONLY UNIT OPERATION OPTION Normal cool / heat / defrost operation OFF OFF OFF OFF OFF OFF
CNF13 : choix (ON/OFF)
Converts unit to a "Heat only" unit Heat only operation (Solara) ON

INVERTABLE MULTI TEMP Not active OFF OFF OFF OFF

CNF14 : choix (ON/OFF)
Indicates to the control if reversible multi temp control is active Reversible multi-temp active ON ON ON

ULTRA FRESH II OPTION (Trailer unit) Logic disabled OFF OFF OFF OFF OFF OFF
CNF15 : choix (ON/OFF)
Indicates to the control if the Ultra Fresh II temperature control is enable Logic enabled ON

SHUNT DOWN WITH ALTERNATOR AUX ALARM Alt aux alarm only OFF
CNF16 : choix (ON/OFF)
Indicates if alternator AUX alarm shuts unit down in diesel mode Alt aux alarm & unit shut down ON ON ON ON ON ON
ULTRA FREEZE 1 OPERATION Disable Ultra freeze 1 OFF OFF OFF OFF OFF OFF
CNF 17 : choix (ON/OFF)
Indicates to the control if UFZ1 operation can run Enable Ultra freeze 1 ON

LOW REFRIGERANT TEST Disable low refrigerrant test OFF

CNF 18 : choix (ON/OFF)
Indicates to the control if low refrigerant test is enable Enable low refrigerrant test ON ON ON ON ON ON
NOT ASSIGNED FOR TRAILER Not used OFF OFF OFF OFF OFF OFF
CNF 19 : choix (ON/OFF)
Not used ON

UNITS SELECTION LOCK OPTION Metric unit or english metric is not locked OFF
CNF 20 : choix (ON/OFF)
Indicates to the control if the units functional parameter is locked Unit selection is locked ON ON METRIC ON METRIC ON METRIC ON METRIC ON METRIC
FROZEN MODE PRIORITY LOGIC OPTION Frozen priority not active OFF OFF OFF OFF
CNF 21 : choix (ON/OFF)
Enables frozen priority logic Active ON ON ON

HOT GAS VALVES DRIVE Together OFF OFF OFF OFF OFF OFF
CNF 22 : choix (ON/OFF)
Indicates if the hot gas valves are driven together or separately Separately ON

SET POINT LOCK Set Point is not locked OFF OFF OFF OFF OFF OFF
CNF 23 : choix (ON/OFF)
Indicates if the change of the Set Point is locked Set Point is locked ON

WT SENSOR ALARM WT sensor alarm only OFF

CNF 24 : choix (ON/OFF)
Indicates if WT sensor alarm shuts unit down WT sensor alarm & unit shut down ON ON ON ON ON ON

CNF 25 to CNF 32 : choix (ON/OFF) Not used OFF OFF OFF OFF OFF OFF

Micro parameters

FN0 Defrost setting : 1,5;3;6;12h 3h 3h 3h 3h 3h

FN1 ON/OFF Air On = high/Off=Norm OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air OFF=Norm air

FN2 Off time choice : 10;20;30;45;90mn 10mn 10mn 10mn 10mn 10mn

FN3 On time choice 4;7 4 mn 4 mn 4 mn 4 mn 4 mn

FN4 A/B PROBE choice A=Rem/B=Sup A=Rem probe A=Rem probe A=Rem probe A=Rem probe B=Sup probe

FN5 F/C degree choix : F or C deg C deg C deg C deg C deg C

FN6 On=time start/ Off=temp start OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt OFF=Temp strt

FN7 MOP choice : STD=0/-=-5/+=+4 STD=0 STD=0 STD=0 STD=0 STD=0

FN8 2SET Set point adjustment 2CP Sans Sans Sans Sans Sans

FN9 3SET Set point adjustment 3CP Sans Sans Sans Sans Sans

FN10 Start Op choice : on=Auto/off=Man On = Auto OP On = Auto OP On = Auto OP On = Auto OP On = Auto OP

FN11 T range choix A=2, B=3, C=4 Dreg C C C C C C

Affichage display T Range choix : CODES OU ENGLISH English English English English English

Manuel glow override choice NORM / ADD Norm Glow Norm Glow Norm Glow Norm Glow Norm Glow

Alarm reset CLR/RST RST RST RST RST RST

Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

VECTOR UNIT MODEL NO: NDP33LN6FBZ

CONFIGURATION PARAMETER SETTINGS FUNCTIONAL PARAMETER SETTINGS

SERIAL NUMBER NO XXXX OPERATING MODE OPTICOLD (by default) ECOFUEL

TRAILER ID XXXX DEFROST TIMER SET FOR 6HRS

GLOW TIME SHORT PERISH MIN RUN TIME 4 MIN

OUT OF RANGE SHUTDOWN NO PERISH MIN OFF TIME 20 MIN 30 MIN

PARAMETERS LOCKOUT NO PERISH OVERRIDE TEMP 3 DEG C 4 DEG C

RPM ALARM SHUTDOWN YES PERISH MAX OFF TIME 0 MIN

LOW PRESSURE SHUTDOWN YES FROZEN MIN RUN TIME 4 MIN

L P SHUTDOWN DELAY 255 SECS FROZEN MIN OFF TIME 30 MIN 45 MIN

HIGH SUC PRESS SHUTDOWN NO FROZEN OVERRIDE TEMP 4 DEG C 5 DEG C

REFRIGERATION SYS SHUTDOWN YES FROZEN MAX OFF TIME 0 MIN

COMPRESSOR ALARM SHUTDOWN NO FROZEN SHUTDOWN OFFSET 0 DEG C

SUCTION PRESSURE 2.1 BAR PERISH SENSITIVE PRODUCT OFF

CURRENT FOR S/S SHUTDOWN 5A TEMP CONTROL RETURN AIR

VOLTAGE FOR S/S RESTART 12,2V DISPLAY TEMP IN (LOCKED) CELCIUS

ENGINE TEMP, FOR S/S RESTART 0,0°C DISPLAY PRESSURES IN (LOCKED) BARS

ALTERNATOR CHECK SHUTDOWN NO ECO MODE NO YES

ENGINE OIL LEVEL SWITCH NO ENGINE HOURS OFF

ENGINE OIL LEVEL SHUTDOWN NO STANDBY HOURS OFF

LOW COOLANT LEVEL NO SWITCH ON HOURS OFF

FUEL SENSOR NO DEVICE PM 1 OFF

FUEL TANK SIZE OFF PM 2 OFF

DIESEL MAX GEN AMPS 26A PM 3 OFF

STANDBY MAX GEN AMPS 22A PM 4 OFF

STARTUP GEN AMPS 17A PM 5 OFF

DIESEL OFFSET MAX AMPS 4A OUT OF RANGE ALARM 4 DEG C

STANDBY STARTUP DELAY OFF LOW SPEED STARTUP: STARTSTOP 0 MINUTES

DISPLAY TOTAL ENGINE HOURS YES LOW SPEED STARTUP: CONTINUOUS 0 MINUTES
DISPLAY STANDBY RUN HOURS YES SILENT MODE NO

DISPLAY TOTAL SWITCH ON HOURS YES SLEEP MODE NO

DIESEL RESET VALUE 0 HOUR OVERRIDE DOOR SHUTDOWN NO

STANDBY RESET VALUE 0 HOUR OVERRIDE REMS1 SHUTDOWN NO

SWITCH ON RESET VALUE 0 HOUR OVERRIDE REMS2 SHUTDOWN NO

PM1 RESET INTERVAL 0 HOUR NO POWER SWITCH TO DIESEL NO

PM2 RESET INTERVAL 0 HOUR

PM3 RESET INTERVAL 0 HOUR

PM4 RESET INTERVAL 0 HOUR

PM5 RESET INTERVAL 0 HOUR

PRODUCT SHIELD ECONO OFF

PRODUCT SHIELD ECONO MIN TEMP OFF

PRODUCT SHIELD ECONO MAX TEMP OFF

PRODUCT SHIELD ECONO DELTA T OFF

PRODUCT SHIELD HIGH AIR OFF

PRODUCT SHIELD HIGH AIR MIN TEMP OFF

PRODUCT SHIELD HIGH AIR MAX TEMP OFF

PRODUCT SHIELD HIGH AIR DELTA T OFF

PRODUCT SHIELD WINTER OFF

RANGE 1 LOCK OFF

RANGE 1 MINIMUN TEMP 32.0 DEG C

RANGE 1 MAXIMUM TEMP 32.0 DEG C

RANGE 2 LOCK OFF

RANGE 2 LOCK MINIMUN TEMP 32.0 DEG C

RANGE 2 LOCK MAXIMUM TEMP 32.0 DEG C

MINIMUM SETPOINT -30 DEG C

MAXIMUM SETPOINT +32 DEG C

NO POWER INSTALLED & SHUTDOWN

START/STOP PARAMETERS SEPARATE

REMOTE TEMP SENSOR 1 OFF

REMOTE TEMP SENSOR 2 OFF

REMOTE TEMP SENSOR 3 OFF

DOOR SWITCH TYPE NOT INSTALLED

DOOR SWITCH SHUTDOWN ALARM ONLY

REMS 1 NOT INSTALLED

REMS 1 ALARM ONLY

REMS 2 NOT INSTALLED

REMS 2 ALARM ONLY

LIGHT BAR 8 LIGHT

8 HR ADDITIONAL DATA NO

DECIMAL DISPLAYED NOT DISPLAYED

CONDENSER PRESSURE CONTROL NO

HIGH SPEED DELAY 1.0 MIN

SUPPLY AIR LIMIT S/S -6.0 DEG C

SUPPLY AIR LIMIT CONT -5.0 DEG C

HIGH SPEED PULLDOWN OPTICOLD: YES (by default) ECOFUEL: NO

SATELLITE COMM OTHER

UNIT OPERATION STANDARD

ENABLE INTELLISET AT = KEY NO

Soft 04.11.0X

Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

VECTOR MT UNIT MODEL NO:NDP33LN6FBR2/3

CONFIGURATION PARAMETER SETTINGS FUNCTIONAL PARAMETER SETTINGS

SERIAL NUMBER NO XXXX OPERATING MODE OPTICOLD (by default) ECOFUEL

TRAILER ID XXXX DEFROST TIMER SET FOR 6HRS

GLOW TIME SHORT PERISH MIN RUN TIME 4 MIN

OUT OF RANGE SHUTDOWN NO PERISH MIN OFF TIME 20 MIN 30 MIN

PARAMETERS LOCKOUT NO PERISH OVERRIDE TEMP 3 DEG C 4 DEG C
RPM ALARM SHUTDOWN YES PERISH MAX OFF TIME 0 MIN

LOW PRESSURE SHUTDOWN YES FROZEN MIN RUN TIME 4 MIN

L P SHUTDOWN DELAY 255 SECS FROZEN MIN OFF TIME 30 MIN 45 MIN
HIGH SUC PRESS SHUTDOWN NO FROZEN OVERRIDE TEMP 4 DEG C 5 DEG C
REFRIGERATION SYS SHUTDOWN YES FROZEN MAX OFF TIME 0 MIN

COMPRESSOR ALARM SHUTDOWN NO FROZEN SHUTDOWN OFFSET 0 DEG C

SUCTION PRESSURE 2.1 BAR PERISH SENSITIVE PRODUCT OFF

CURRENT FOR S/S SHUTDOWN 7A TEMP CONTROL RETURN AIR

VOLTAGE FOR S/S RESTART 12,2V DISPLAY TEMP IN (LOCKED) CELCIUS

ENG TEMP FOR S/S RESTART 0°C DISPLAY PRESSURES IN (LOCKED) BARS
ALTERNATOR CHECK SHUTDOWN NO ECO MODE NO YES
ENGINE OIL LEVEL SWITCH NO ENGINE HOURS OFF

ENGINE OIL LEVEL SHUTDOWN NO STANDBY HOURS OFF

LOW COOLANT LEVEL NO SWITCH ON HOURS OFF

FUEL SENSOR NO DEVICE PM 1 OFF

FUEL TANK SIZE OFF PM 2 OFF

DIESEL MAX GEN AMPS 26A PM 3 OFF

STANDBY MAX GEN AMPS 22A PM 4 OFF

STARTUP GENERATOR CURRENT 17A PM 5 OFF

DIESEL OFFSET FOR CURRENT 4A OUT OF RANGE ALARM 4 DEG C

STANDBY START UP DELAY OFF C2 OUT OF RANGE ALARM 4 DEG C

DISPLAY TOTAL ENGINE HOURS YES C3 OUT OF RANGE ALARM (BR3 only) 4 DEG C

DISPLAY TOTAL STANDBY HOURS YES LOW SPEED STARTUP: STARTSTOP 0 MINUTES
DISPLAY TOTAL SWITCH ON HOURS YES LOW SPEED STARTUP: CONTINUOUS 0 MINUTES
DIESEL RESET VALUE 0 HOUR SILENT MODE NO

STANDBY RESET VALUE 0 HOUR SLEEP MODE NO

SWITCH ON RESET VALUE 0 HOUR OVERRIDE DOOR SHUTDOWN (BR2 only) NO

PM1 RESET INTERVAL 0 HOUR NO POWER SWITCH TO DIESEL NO

PM2 RESET INTERVAL 0 HOUR

PM3 RESET INTERVAL 0 HOUR

PM4 RESET INTERVAL 0 HOUR

PM5 RESET INTERVAL 0 HOUR

PRODUCT SHIELD ECONO OFF

PRODUCT SHIELD ECONO MIN TEMP OFF

PRODUCT SHIELD ECONO MAX TEMP OFF

PRODUCT SHIELD ECONO DELTA T OFF

PRODUCT SHIELD HIGH AIR OFF

PRODUCT SHIELD HIGH AIR MIN TEMP OFF

PRODUCT SHIELD HIGH AIR MAX TEMP OFF

PRODUCT SHIELD HIGH AIR DELTA T OFF

PRODUCT SHIELD WINTER OFF

RANGE 1 LOCK OFF

RANGE 1 MINIMUN TEMP 32.0 DEG C

RANGE 1 MAXIMUM TEMP 32.0 DEG C

RANGE 2 LOCK OFF

RANGE 2 LOCK MINIMUN TEMP 32.0 DEG C

RANGE 2 LOCK MAXIMUM TEMP 32.0 DEG C

MINIMUM SETPOINT -30 DEG C

MAXIMUM SETPOINT +32 DEG C

C2 SETPOINT MINIMUM -30 DEG C

C2 SETPOINT MAXIMUM +32 DEG C

C3 SETPOINT MINIMUM (BR3 only) -30 DEG C

C3 SETPOINT MAXIMUM (BR3 only) +32 DEG C

NO POWER INSTALLED & SHUTDOWN

STOP/START PARAMETERS SEPARATE

REMOTE TEMP SENSOR 1 (BR2 only) OFF

REMOTE TEMP SENSOR 2 (BR2 only) OFF

DOOR SWITCH TYPE (BR2 only) NOT INSTALLED

DOOR SWITCH ALARM (BR2 only) ALARM ONLY

LIGHT BAR 2 LIGHT

8 HR ADDITIONAL DATA NO

FRESH NULL MODE FAN CYCLE OFF

FROZEN COMP PRIORITY OFF

FROZEN PRIORITY TIMER 5 MINUTES

NON PRIORITY TIME 5 MINUTES

CONDENSER PRESSURE CONTROL NO

HIGH SPEED DELAY 1.0 MIN

SUPPLY AIR LIMIT S/S -6.0 DEG C

SUPPLY AIR LIMIT CONT -5.0 DEG C

SAT 2 NOT INSTALLED

C2 SUPPLY AIR LIMIT FOR S/S -3.0 DEG C

C2 SUPPLY AIR LIMIT FOR CONT -1;0 DEG C

HIGH SPEED PULLDOWN OPTICOLD: YES (by default) ECOFUEL: NO

SATELLITE COMM OTHER

UNIT OPERATION STANDARD

ENABLE INTELLISET AT = KEY NO

Soft 04.11.0X

Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

TM1000 / TM800
TM 1000 / TM800
MICRO configuration Description Soft 3.33
GLOW TIME DI Engine long glow cycle DI
CNF1: choix(DI/TV)
Indicates to the control which engine is in the system and which glow time should be TV Engine short glow cycle TV TV
DISCHARGE SENSOR CDT not used OFF
CNF2 : choix (ON/OFF)
Indicates to the control if the DISCHARGE sensor is installed CDT used ON ON
HIGH SETPOINT 30°c (86°F) Max. Set point OFF OFF
CNF3 : choix (ON/OFF)
Indicates maximum Set Point allowed 32°c (90°F) Max. Set point ON
HEAT LOCKOUT OVERRIDE (Maxima MT Only) Heat lockout on -12°c (10°F) OFF OFF
CNF4 : choix (ON/OFF)
Indicates to the control if the heat lockout is overridden Heat lockout off ON
MOP MOP disabled OFF
CNF5 : choix (ON/OFF)
Indicates status of MOP control MOP enabled ON ON
TRUCK UNIT Trailer unit OFF OFF
CNF6 : choix (ON/OFF)
Indicates to the control if the system has been selected for truck operation Truck unit ON
HIGH SPEED OVERRIDE Logic disabled OFF OFF
CNF7 : choix (ON/OFF)
Indicates to the control if the low speed coolant check logic is enabled Logic enabled ON
ELECTRIC FAN Belt driven fan OFF OFF
CNF8 : choix (ON/OFF)
Indicates to the control if electric fans are being used Electrical fan motors ON
OUT-OF-RANGE SHUT DOWN Out of range alarm only OFF
CNF9 : choix (ON/OFF)
Indicates if main compartment out-of-range alarm shuts unit down after 45min. Out of range alarm and unit shut down ON ON
NOT ASSIGNED FOR TRAILER Not used OFF OFF
CNF10 : choix (ON/OFF)
Not used ON
FUNCTIONAL PARAMETERS (KEYPAD) LOCKOUT OPTION Functions normal OFF OFF
CNF11 : choix (ON/OFF)
Allow or lockout certain any changes of the functional parameter from keypad Functions locked ON
HP-62 MOP OPTION MOP parameter HP 62 option OFF
CNF12 : choix (ON/OFF)
Use either normal or HP-62 MOP parameters Active ON ON
HEAT ONLY UNIT OPERATION OPTION Normal cool / heat / defrost operation OFF OFF
CNF13 : choix (ON/OFF)
Converts unit to a "Heat only" unit Heat only operation (Solara) ON
INVERTABLE MULTI TEMP Not active OFF
CNF14 : choix (ON/OFF)
Indicates to the control if reversible multi temp control is active Reversible multi-temp active ON ON
ULTRA FRESH II OPTION (Trailer unit) Logic disabled OFF
CNF15 : choix (ON/OFF)
Indicates to the control if the Ultra Fresh II temperature control is enable Logic enabled ON ON
SHUNT DOWN WITH ALTERNATOR AUX ALARM Alt aux alarm only OFF
CNF16 : choix (ON/OFF)
Indicates if alternator AUX alarm shuts unit down in diesel mode Alt aux alarm & unit shut down ON ON
ULTRA FREEZE 1 OPERATION Disable Ultra freeze 1 OFF
CNF 17 : choix (ON/OFF)
Indicates to the control if UFZ1 operation can run Enable Ultra freeze 1 ON ON
LOW REFRIGERANT TEST Disable low refrigerrant test OFF
CNF 18 : choix (ON/OFF)
Indicates to the control if low refrigerant test is enable Enable low refrigerrant test ON ON
NOT ASSIGNED FOR TRAILER Not used OFF OFF
CNF 19 : choix (ON/OFF)
Not used ON
UNITS SELECTION LOCK OPTION Metric unit or english metric is not locked OFF OFF
CNF 20 : choix (ON/OFF)
Indicates to the control if the units functional parameter is locked Unit selection is locked ON
FROZEN MODE PRIORITY LOGIC OPTION Frozen priority not active OFF OFF
CNF 21 : choix (ON/OFF)
Enables frozen priority logic Active ON
HOT GAS VALVES DRIVE Together OFF OFF
CNF 22 : choix (ON/OFF)
Indicates if the hot gas valves are driven together or separately Separately ON
SET POINT LOCK Set Point is not locked OFF OFF
CNF 23 : choix (ON/OFF)
Indicates if the change of the Set Point is locked Set Point is locked ON
WT SENSOR ALARM WT sensor alarm only OFF
CNF 24 : choix (ON/OFF)
Indicates if WT sensor alarm shuts unit down WT sensor alarm & unit shut down ON ON

CNF 25 to CNF 32 : choix (ON/OFF) Not used OFF OFF

Micro parameters
FN0 Defrost setting : 1,5;3;6;12h 6H
FN1 ON/OFF Air On = high/Off=Norm Norm
FN2 Off time choice : 10;20;30;45;90mn 20
FN3 On time choice 4;7 4
FN4 A/B PROBE choice A=Rem/B=Sup Rem
FN5 F/C degree choix : F or C °C
FN6 On=time start/ Off=temp start time start
FN7 MOP choice : STD=0/-=-5/+=+4 MOP +
FN8 2SET Set point adjustment 2CP 32°F or O°c
FN9 3SET Set point adjustment 3CP 32°F or O°c
FN10 Start Op choice : on=Auto/off=Man Auto Op
FN11 T range choix A=2, B=3, C=4 Dreg C T range A
Affichage display T Range choix : CODES OU ENGLISH English
Manuel glow override choice NORM / ADD Norm
Alarm reset CLR/RST CLR

Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

TR1000
Description TR1000
MICRO configuration
Soft 4,06
DI DI Engine long glow cycle
CNF1: choix(DI/TV)
TV TV Engine short glow cycle TV
OFF CDT not used
CNF2 : choix (ON/OFF)
ON CDT used ON
OFF 30°c (86°F) Max. Set point OFF
CNF3 : choix (ON/OFF)
ON 32°c (90°F) Max. Set point
OFF Heat lockout on -12°c (10°F) OFF
CNF4 : choix (ON/OFF)
ON Heat lockout off (truck units)
OFF MOP disabled
CNF5 : choix (ON/OFF)
ON MOP enabled ON
OFF Trailer unit OFF
CNF6 : choix (ON/OFF)
ON Truck unit
OFF Low speed start OFF
CNF7 : choix (ON/OFF)
ON High speed start
OFF Belt driven fan OFF
CNF8 : choix (ON/OFF)
ON Electrical fan motors
OFF Out of range alarm not shut down OFF (option)
CNF9 : choix (ON/OFF)
ON Out of range alarm and unit shut down
OFF No auto restart OFF
CNF10 : choix (ON/OFF)
ON Auto restart active
OFF Functions normal OFF (option)
CNF11 : choix (ON/OFF)
ON Functions locked
OFF MOP parameter HP 62 option OFF
CNF12 : choix (ON/OFF)
ON Active
OFF Cool / heat / defrost OFF
CNF13 : choix (ON/OFF)
ON Heat only (Solara)
OFF Not active OFF
CNF14 : choix (ON/OFF)
ON
OFF Not active OFF
CNF15 : choix (ON/OFF)
ON
OFF Alt aux alarm only
CNF16 : choix (ON/OFF)
ON Alt aux alarm & unit shut down ON

FN0 Defrost setting : 1,5;3;6;12h 6H

FN1 ON/OFF Air On = high/Off=Norm Norm
FN2 Off time choice : 10;20;30;45;90mn 20
FN3 On time choice 4;7 7
FN4 A/B PROBE choice A=Rem/B=Sup Rem
FN5 F/C degree choix : F or C °C
FN6 On=time start/ Off=temp start temp start
FN7 MOP choice : STD=0/-=-5/+=+4 MOP STD
FN8 2SET Set point adjustment 2CP 32°F or O°c
FN9 3SET Set point adjustment 3CP 32°F or O°c
FN10 Start Op choice : on=Auto/off=Man Man
FN11 T range choix A=2, B=3, C=4 Dreg C T range B
Affichage display T Range choix : CODES OU ENGLISH English
Manuel glow override choice NORM / ADD Norm
Alarm reset CLR/RST CLR

Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

ULTRA
Ultra/Optima
Extra XT
Extra
MICRO configuration Description
Soft 3.33 3.33

GLOW TIME DI Engine long glow cycle DI

CNF1: choix(DI/TV)
Indicates to the control which engine is in the system and which glow time should be TV Engine short glow cycle TV TV TV
DISCHARGE SENSOR CDT not used OFF
CNF2 : choix (ON/OFF)
Indicates to the control if the DISCHARGE sensor is installed CDT used ON ON ON
HIGH SETPOINT 30°c (86°F) Max. Set point OFF OFF (Option) OFF (Option)
CNF3 : choix (ON/OFF)
Indicates maximum Set Point allowed 32°c (90°F) Max. Set point ON
HEAT LOCKOUT OVERRIDE (Maxima MT Only) Heat lockout on -12°c (10°F) OFF OFF OFF
CNF4 : choix (ON/OFF)
Indicates to the control if the heat lockout is overridden Heat lockout off ON
MOP MOP disabled OFF
CNF5 : choix (ON/OFF)
Indicates status of MOP control MOP enabled ON ON ON
TRUCK UNIT Trailer unit OFF OFF OFF
CNF6 : choix (ON/OFF)
Indicates to the control if the system has been selected for truck operation Truck unit ON
HIGH SPEED OVERRIDE Logic disabled OFF OFF OFF
CNF7 : choix (ON/OFF)
Indicates to the control if the low speed coolant check logic is enabled Logic enabled ON
ELECTRIC FAN Belt driven fan OFF OFF OFF
CNF8 : choix (ON/OFF)
Indicates to the control if electric fans are being used Electrical fan motors ON
OUT-OF-RANGE SHUT DOWN Out of range alarm only OFF OFF (Option) OFF (Option)
CNF9 : choix (ON/OFF)
Indicates if main compartment out-of-range alarm shuts unit down after 45min. Out of range alarm and unit shut down ON
NOT ASSIGNED FOR TRAILER Not used OFF OFF OFF
CNF10 : choix (ON/OFF)
Not used ON
FUNCTIONAL PARAMETERS (KEYPAD) LOCKOUT OPTION Functions normal OFF OFF (Option) OFF (Option)
CNF11 : choix (ON/OFF)
Allow or lockout certain any changes of the functional parameter from keypad Functions locked ON
HP-62 MOP OPTION MOP parameter HP 62 option OFF
CNF12 : choix (ON/OFF)
Use either normal or HP-62 MOP parameters Active ON ON ON
HEAT ONLY UNIT OPERATION OPTION Normal cool / heat / defrost operation OFF OFF OFF
CNF13 : choix (ON/OFF)
Converts unit to a "Heat only" unit Heat only operation (Solara) ON
INVERTABLE MULTI TEMP Not active OFF OFF OFF
CNF14 : choix (ON/OFF)
Indicates to the control if reversible multi temp control is active Reversible multi-temp active ON
ULTRA FRESH II OPTION (Trailer unit) Logic disabled OFF
CNF15 : choix (ON/OFF)
Indicates to the control if the Ultra Fresh II temperature control is enable Logic enabled ON ON (Option) ON (Option)
SHUNT DOWN WITH ALTERNATOR AUX ALARM Alt aux alarm only OFF OFF (Option) OFF (Option)
CNF16 : choix (ON/OFF)
Indicates if alternator AUX alarm shuts unit down in diesel mode Alt aux alarm & unit shut down ON
ULTRA FREEZE 1 OPERATION Disable Ultra freeze 1 OFF
CNF 17 : choix (ON/OFF)
Indicates to the control if UFZ1 operation can run Enable Ultra freeze 1 ON ON (Option) ON (Option)
LOW REFRIGERANT TEST Disable low refrigerrant test OFF
CNF 18 : choix (ON/OFF)
Indicates to the control if low refrigerant test is enable Enable low refrigerrant test ON ON (Option) ON (Option)
XT units Non-XT units OFF OFF
CNF 19 : choix (ON/OFF)
XT units only ON ON
UNITS SELECTION LOCK OPTION Metric unit or english metric is not locked OFF OFF (Option) OFF (Option)
CNF 20 : choix (ON/OFF)
Indicates to the control if the units functional parameter is locked Unit selection is locked ON
FROZEN MODE PRIORITY LOGIC OPTION Frozen priority not active OFF NA NA
CNF 21 : choix (ON/OFF)
Enables frozen priority logic Active ON
HOT GAS VALVES DRIVE Together OFF NA NA
CNF 22 : choix (ON/OFF)
Indicates if the hot gas valves are driven together or separately Separately ON
SET POINT LOCK Set Point is not locked OFF OFF OFF
CNF 23 : choix (ON/OFF)
Indicates if the change of the Set Point is locked Set Point is locked ON
WT SENSOR ALARM WT sensor alarm only OFF
CNF 24 : choix (ON/OFF)
Indicates if WT sensor alarm shuts unit down WT sensor alarm & unit shut down ON ON ON

CNF 25 to CNF 32 : choix (ON/OFF) Not used OFF OFF OFF

Micro parameters
FN0 Defrost setting : 1,5;3;6;12h 6H 6H
FN1 ON/OFF Air On = high/Off=Norm OFF=Norm air OFF=Norm air
FN2 Off time choice : 10;20;30;45;90mn 10 mn 10 mn
FN3 On time choice 4;7 4 mn 4 mn
FN4 A/B PROBE choice A=Rem/B=Sup A=rem Probe A=rem Probe
FN5 F/C degree choix : F or C Deg F Deg F
FN6 On=time start/ Off=temp start OFF=temp strt OFF=temp strt
FN7 MOP choice : STD=0/-=-5/+=+4 STD=0 STD=0
FN8 2SET Set point adjustment 2CP sans sans
FN9 3SET Set point adjustment 3CP sans sans
FN10 Start Op choice : on=Auto/off=Man ON=Auto OP ON=Auto OP
FN11 T range choix A=2, B=3, C=4 Dreg C C C
Affichage display T Range choix : CODES OU ENGLISH English English
Manuel glow override choice NORM / ADD Norm Glow Norm Glow
Alarm reset CLR/RST CLR CLR

Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

XARIOS
Xarios
Xarios 150/150- Xarios Xarios
150/150-
04/200/200- 350/350- 350/350- Xarios Xarios
XARIOS ROAD / 04/200/200- with Hot gas with Hot gas
MICRO CONFIGURATION 04/300/300-05 05/400/500-04 05/400/500-04 500/600/ road 500/600/ road
STAND-BY 04/300/300-05 heating option heating option
road / stand-by road / stand- road / stand- / stand-by 12v / stand-by 24v
road / stand-
12v by 12v by 24v
by 24v
DEFROST AUT AUT AUT AUT AUT AUT
BRIGHTNESS HIGH HIGH HIGH HIGH HIGH HIGH

UNIT (Ut) Ut °C Ut °C Ut °C Ut °C Ut °C Ut °C
BATTERY VOLTAGE (PS) PS 12 PS 24 PS 12 PS 24 PS 12 PS 24
NUMBER OF FAN (FAn) Fan1 Fan1 Fan2 Fan2 Fan3 Fan3
configuration

FAN SPEED (SPd) SPD3 SPD3 SPD3 SPD3 SPD3 SPD3

NUMBER OF STAGES (ET) 2ET 2ET 3ET 2ET 2ET 3ET 3ET 3ET
OPTIONNAL HEATING ROAD (hr) hrof hrof hrof hrof hrof hrof
OPTIONNAL HEATING STANDBY (hs) hsof hsof hsof hsof hsof hsof
OPTIONNAL DRAIN RESISTOR (dr) drof drof drof drof drof drof
OPTIONNAL DOOR SWITCH (d) doff doff doff doff doff doff
* HYBRID UNIT ONLY (eu) euof euof euof euof euof euof
* OPTIONNAL SET POINT LOCK spof spof spof spof spof spof

SET POINT 0°C 0°C 0°C 0°C 0°C 0°C

Parameters

LOW SET POINT - 29 °C - 29 °C - 29 °C - 29 °C - 29 °C - 29 °C

HIGH SET POINT + 20 °C + 20 °C + 20 °C + 20 °C + 20 °C + 20 °C

TEMPERATURE DIFFERENCIAL (dif) dif1 dif1 dif1 dif1 dif1 dif1

EVAPORATOR FAN CONTINUOUS RUN (F) Foff Foff Foff Foff Foff Foff

* starting with soft 1,91

xarios 150-04 / 200-

XARIOS ROAD xarios 150-04 / 200-04 /
MICRO CONFIGURATION 04 / 300-05 / 350-05
ONLY 300-05 / 350-05 12V
24V

10mn 10mn
DEFROST
1h 1h
BRIGHTNESS HIGH HIGH

UNIT (Ut) Ut °C Ut °C
configurations

BATTERY VOLTAGE (PS) _ _

NUMBER OF FAN (FAn) _ _
FAN SPEED (SPd) _ _
NUMBER OF STAGES (ET) 3 3
OPTIONNAL HEATING ROAD (hr) _ _
OPTIONNAL HEATING STANDBY (hs) _ _
DRAIN RESISTOR (dr) _ _
DOOR SWITCH (d) _ _

SET POINT 0°C 0°C

LOW SET POINT 0 0

parameters

HIGH SET POINT 30°C 30°C

TEMPERATURE DIFFERENCIAL (dif) dif2 dif2

EVAPORATOR FAN CONTINUOUS RUN (F) off off

XARIOS MT
xarios 350/350-05 Xarios 500 MT Xarios 600 MT Xarios 600 MT
ROAD / ROAD xarios 350/350-05 MT Xarios 500 MT Road /
MICRO CONFIGURATION MT Road / road Road / Road stand- Road / Road stand- Road / Road stand-
STANDBY Road / road stand-by 12v Road stand-by 12v
stand-by 24v by 24v by 12V by 24V
DEFROST operating mode selection Simu Simu Simu Simu Simu Simu
DEFROST interval 3H 3H 3H 3H 3H 3H
BRIGHTNESS HIGH HIGH HIGH HIGH HIGH HIGH

UNIT (Ut) Ut °C Ut °C Ut °C Ut °C Ut °C Ut °C
BATTERY VOLTAGE (PS) PS 12 PS 24 PS 12 PS 24 PS 12 PS 24

** to be selected ** to be ** to be ** to be ** to be ** to be
configurations

NUMBER OF FAN (FAn) selected selected selected selected selected

regarding
regarding regarding regarding regarding regarding
evaporators
evaporators evaporators evaporators evaporators evaporators
FAN SPEED (SPd) SPD3 SPD3 SPD3 SPD3 SPD3 SPD3
NUMBER OF STAGES (ET) / / / / / /
OPTIONNAL HEATING ROAD (hr) hrof hrof hrof hrof hrof hrof
OPTIONNAL HEATING STANDBY (hs) hsof hsof hsof hsof hsof hsof
DRAIN RESISTOR (dr) drof drof drof drof drof drof
DOOR SWITCH (d) doff doff doff doff doff doff
ALARM OUT OF RANGE (al) aloff aloff aloff aloff aloff aloff

SET POINT 0°C/-20°C 0°C/-20°C 0°C/-20°C 0°C/-20°C 0°C/-20°C 0°C/-20°C

COOLING operating mode selection Auto Auto Auto Auto Auto Auto
parameters

LOW SET POINT - 29 °C - 29 °C - 29 °C - 29 °C - 29 °C - 29 °C

HIGH SET POINT + 20 °C + 20 °C + 20 °C + 20 °C + 20 °C + 20 °C

TEMPERATURE DIFFERENCIAL (dif) dif2 dif2 dif2 dif2 dif2 dif2

EVAPORATOR FAN CONTINUOUS RUN (F) Foff Foff Foff Foff Foff Foff

** MXS 600 fan1

** MXS 850 fan1
** MXV 850 fan1
** MXL 1100 fan2

Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

NEOS
Road Road/Standby
MICRO CONFIGURATION
DEFROST AUT AUT
SET POINT 0°C 0°C
UNITY (Ut) Ut °C Ut °C
BATTERY VOLTAGE (PS) PS 12 PS 12
NUMBER OF STAGES (ET) 3ET 3ET
DOOR SWITCH (d) doff doff
LOW SET POINT - 29 °C - 29 °C
TEMPERATURE DIFFERENCIAL (dif) dif2 dif2
EVAPORATOR FAN CONTINUOUS RUN (F) Foff Foff

Update 06/07/2009
 MICRO CONFIGURATIONS AND FUNCTIONS

VIENTO
VIENTO VIENTO
VIENTO VIENTO VIENTO VIENTO
VIENTO ROAD VIENTO 350 CH VIENTO 350 VIENTO 350 200 LA / 200 LA /
MICRO CONFIGURATION 300 CH 300 LA / 300 LA / 200 CH
ONLY R134A LA / HA R134A LA / HA R404A HA HA
R134A HA R134A HA R404A R134A
R134A R404A
Soft version SOFTWARE 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0 4,0
DEFROST NATURAL 1H - 15' 1H - 15' NATURAL 1H - 15' 1H - 15' NATURAL 1H - 15' 1H - 15'
BRIGHTNESS - - - - - - - - -
- - - - - - -
UNIT (Ut) Ut °C Ut °C Ut °C Ut °C Ut °C Ut °C Ut °C Ut °C Ut °C
BATTERY VOLTAGE (PS) - - - - - - - - -
configuration

NUMBER OF FAN (FAn) - - - - - - - - -

FAN SPEED (SPd) - - - - - - - - -
NUMBER OF STAGES (ET) 2ET* 3ET* 3ET* 2ET* 3ET* 3ET* 2ET* 3ET* 3ET*
OPTIONNAL HEATING ROAD (hr) - - - - - - - - -
OPTIONNAL HEATING STANDBY (hs) - - - - - - - - -
OPTIONNAL DRAIN RESISTOR (dr) - - - - - - - - -
OPTIONNAL DOOR SWITCH (d) - - - - - - - -
SET POINT 0°C 0°C 0°C 0°C 0°C 0°C 0°C 0°C 0°C
Parameters

LOW SET POINT 0°C 0°C 0°C 0°C 0°C 0°C 0°C 0°C 0°C
HIGH SET POINT + 30 °C + 30 °C + 30 °C + 30 °C + 30 °C + 30 °C + 30 °C + 30 °C + 30 °C
TEMPERATURE DIFFERENCIAL (dif) dif2 dif2 dif2 dif2 dif2 dif2 dif2 dif2 dif2
EVAPORATOR FAN CONTINUOUS RUN (F) Foff Foff Foff Foff Foff Foff Foff Foff Foff

* preset in the micro software

Update 06/07/2009