Catalogo Soportes

OCTOBER 2019
PIPE HANGERS & SUPPORTS
MADE IN THE USA

THE COMPLETE LINE OF
PIPE HANGERS, SUPPORT SYSTEMS
AND ACCESSORIES
PIPE HANGERS AND SUPPORTS • CUSTOM FABRICATION • ENGINEERING
NATIONAL
PIPE HANGER CORPORATION
Introduction
National Pipe Hanger Corporation is proud to present our updated catalog containing a
complete and versatile line of pipe hangers, pipe support systems and related products.
This selection results from more than forty-five years of concentrated and direct exposure
to the piping industry, from the design engineer’s selection, to the piping contractor’s instal-
lation. This is where needs are discovered and where products and services are genuinely
tested. In this area, National Pipe Hanger Corporation’s experiences are unequaled. These
products have been selected to effectively answer any pipe support issue in the plumbing,
mechanical, HVAC and industrial fields. National Pipe Hanger Corporation’s comprehensive
line of quality products includes domestically manufactured pipe hangers, pre-insulated pipe
supports, pipe guides, pipe clamps, pipe support chairs and stands, brackets, beam clamps,
saddles and accessories just to name a few.
National Pipe Hanger Corporation takes pride in being an American manufacturing company
in the United States. A constant awareness of the customers’ requirements and efforts is the
foundation in the development of National Pipe Hanger Corporation’s manufacturing skills.
All of National Pipe Hanger Corporation’s products are carefully manufactured to meet the
highest standards in the industry. Our 75,000 square foot manufacturing facility in NJ can
accommodate any project nationwide. National Pipe Hanger Corporation is a full service
fabricator with A.W.S. – D1.1 certified welders, a participating member of the Manufacturer’s
Standardization Society (MSS) and manufactures pipe hangers and supports in accordance
with MSS Standard Practice SP-58. Many of National Pipe Hanger Corporation’s products
meet and exceed Factory Mutual Listings (FM), Underwriters Laboratory Listings (UL), and
Federal Specifications (WW-H-171E).
In addition to a wide range of high-quality hangers, National Pipe Hanger Corporation offers
custom options backed by our skilled engineers. Contact National Pipe Hanger Corpora-
tion’s New Jersey headquarters or Maryland branch for special pipe support requirements
including: other pipe sizes and types, dimensional requirements, installation methods, fin-
ishes, etc. National Pipe Hanger Corporation’s sales team will always provide you with
impeccable service and will respond quickly to your product and service needs on both
standard items and specialized fabrications. For a detailed look at National Pipe Hanger
Corporation’s Pre-Insulated Pipe Supports, please refer to our Pre-Insulated Pipe Supports
catalog. Visit our website at nationalpipehanger.com for additional information.
All units in this catalog are inch-pound unless otherwise noted. Additional information pro-
vided at the end of this catalog can aid the user in: types of finishes, estimating pipe support
loads, the outer diameter of various types of pipe, determining pipe support spacing, deter-
mining rod size by pipe size and determining thickness of sheet metal by gauge.
National Pipe Hanger Corporation reserves the right to make specification changes without
notice. While every effort has been made to assure the accuracy of information contained
in this catalog at the time of publication, National Pipe Hanger Corporation cannot accept
responsibility for inaccuracies resulting from undetected errors or omissions.
1
NATIONAL PIPE HANGER CORPORATION
Pictorial Table of Contents

06 06 07 08 09
Hold Down Strap for Offset Return

Split Ring Extension Hanger Hanger Flange Adjustable Swivel Ring Hanger IPS & DI Pipe Line J-Hook
FIG. 100 FIG. 105 FIG. 110 FIG. 136 & FIG. 137 FIG. 155
09 09 10 11 11
Adjustable Clevis Hanger,

U-Bolt for IPS U-Bolt for DI Pipe Adjustable Clevis Hanger PVC Flat Top Clevis Hanger
FIG. 165 FIG. 166 FIG. 200 FIG. 200 FIG. 205
12 12 13 13 13
Adjustable Clevis Hanger Adjustable Clevis Hanger Clevis Hanger w/ Clevis Hanger w/ V-Bottom Adjustable
w/ Extended Bottom for DI Pipe Welded Shield Welded MSS Shield Clevis Hanger
14 14 15 15 16
V-Channel Roller Chair Pipe Roller Stand Adjustable Pipe Roller Stand Adjustable Roller Hanger
16 17 18 19-20 19-20
Adjustable Two-Rod Roller Pipe Covering Protection Shield MSS Pipe Covering Pipe Covering Pipe Covering
Hanger Solid & w/ Hole Protection Shield Protection Saddle Protection Saddle
FIG. 260 FIG. 300 & FIG. 302 FIG. 307 FIG. 310-340 FIG. 310-340
21 22 21 23 23
Standard Steel Heavy Duty Two-Bolt Heavy Duty Double Bolt

Pipe Clamp Heavy Duty Riser Clamp Pipe Clamp Double Bolt Pipe Clamp Pipe Clamp
2

24 25 26 26 27
Four Section
Riser Clamp Offset Pipe Clamp Extended Pipe Clamp Rodding Band Socket Clamp for DI Pipe
27 28 28 28 29
Four-Bolt Socket Four-Bolt Socket

Socket Clamp Washer Clamp for DI Pipe Clamp Washer Corporation Eye Bolt Pipe Alignment Guide
30 31 31 32 32
Adjustable Pipe Support w/ Pipe Saddle Support w/ Pipe Saddle Support w/

Light Duty Pipe Alignment Guide Adjustable Pipe Support U-Bolt for IPS & DI Pipe U-Bolt for DI Pipe U-Bolt for IPS Pipe
FIG. 502 FIG. 515 FIG. 516 & FIG. 517 FIG. 519 FIG. 520
32 33 33 34 34
Adjustable Pipe Saddle Adjustable Pipe Saddle Adjustable Pipe Saddle Support
Pipe Saddle Support Pipe Saddle Support Support w/ Coupling Support w/ U-Bolt for IPS Pipe
34 35 36 35 37
Adjustable Pipe Saddle Support

w/ U-Bolt for DI Pipe Angle Iron Support Channel Assembly Angle Bracket Metal Deck Anchor Bolt
38 39 39 39 39
Female Overhead
Anchor Bolt Concrete Insert Box Concrete Insert Nut C-Clamp C-Clamp w/ Locknut
3

40 39 40 41 41
Purlin Clamp C-Clamp Retaining Strap Electrical Beam Clamp Jr. Top Beam Clamp Jr. Top Beam Clamp, Domestic
42 42 42 43 43
Top Beam Clamp Retaining Welding Beam Attachment

Strap Jr. Top Beam Clamp, Domestic Wide Top Beam Clamp Welding Beam Attachment w/ Bolt & Nut
44 44 45 45 46
Concrete Rod
Attachment Plate Concrete Clevis Plate Side Beam Connector Adjustable Rod Beam Clamp Adjustable Center Beam Clamp
47 49 49 48 49
Malleable Beam Clamp Light Welded Steel

Center Beam Clamp Malleable Beam Clamp w/ Extension Piece Beam Clamp Assembly Bracket
50 50 51 51 51
Medium Welded Steel Heavy Welded Steel Light Welded Steel

Bracket Bracket Bracket Side Clip Turnbuckle
52 52 53 53 54
Continuous
Forged Steel Clevis Weldless Eye Nut Swivel Hanger Male/Female Threaded Rod Rod Coupling
4

54 54 55 55 55
Reducing Rod Coupling Hex Head Machine Bolts Finished Hex Nuts Heavy Duty Hex Nuts Round Steel Washers
55 56 56 56 57
Lock Washer Steel Washer Plate Fender Washers Round Head Machine Screws Pipe Sleeve
57 57 58 58 58
Nailing Sleeve Waterproof Sleeve Wood-Knocker Bang-It Vertigo

59 59 59 59 60
Sleeve Anchor
Wedge Anchor w/ Coupling Sleeve Anchor Mini Drop-In Anchor Drop-In Anchor
60 59 60 60 60
Spring Wing Toggle Spring Wing Toggle

Drop-In Setting Tool Mini Drop-In Setting Tool Hammer Drive Anchor w/ Bolt Head Only
61 61 61 62 62
Neoprene-In-Shear Neoprene-In-Shear
Hanger Spring Hanger Spring Hanger Pipe Slide & Guide Pipe Anchor
FIG. 900 FIG. 901 FIG. 902 FIG. 950S, G & U FIG. 950A
5
FIG. 100 Split Ring Extension Hanger
SERVICE: For suspension of non-insulated, stationary piping and

copper tubing services.
MATERIAL: Malleable Iron or 304 Stainless Steel
FINISH: Black, Electro-Galvanized or Copper Epoxy Coated
(COPPER-GARD)
STANDARDS: MSS SP-58 Type 12, FS WW-H-171E Type 25
ORDERING: Specify figure number, pipe/tube size, material and finish.
PIPE PIPE WEIGHT MAX REC.
SCREW A B C D
SIZE OD EACH, LBS. LOAD, LBS.
3
/8 0.675 10 - 24 3
/8 11
/16 113/16 13/16 0.08 180
1
/2 0.840 10 - 24 3
/8 3
/4 21/8 13/16 0.10 180
3
/4 1.050 10 - 24 3
/8 7
/8 21/2 19/16 0.11 180
1 1.315 10 - 24 3
/8 11/8 23/4 2 0.15 180
11/4 1.660 10 - 24 3
/8 15/16 33/16 23/8 0.18 180
11/2 1.900 10 - 24 3
/8 17/16 33/8 25/8 0.21 180
2 2.375 10 - 24 3
/8 15/8 315/16 31/16 0.30 180
21/2 2.875 1
⁄4 1
/2 21/8 53/16 313/16 0.58 300
3 3.500 1
⁄4 1
/2 21/2 511/16 45/8 0.71 300
4 4.500 1
⁄4 1
/2 27/8 63/4 59/16 1.02 300
TUBE TUBE WEIGHT MAX REC.
SCREW A B C D
SIZE OD EACH, LBS. LOAD, LBS.
/4
1
0.375 10 - 24 3
/8 9
/16 13/4 7
/8 0.07 180
/8
3
0.500 10 - 24 3
/8 5
/8 13/4 11/16 0.08 180
1
/2 0.625 10 - 24 3
/8 11
/16 17/8 11/8 0.09 180
3
/4 0.875 10 - 24 3
/8 13
/16 21/4 13/8 0.10 180
1 1.125 10 - 24 3
/8 15
/16 21/2 15/8 0.13 180
11/4 1.375 10 - 24 3
/8 11/16 27/8 17/8 0.14 180
11/2 1.625 10 - 24 3
/8 13/16 3 23/16 0.18 180
2 2.125 10 - 24 3
/8 17/16 31/2 211/16 0.23 180
21/2 2.625 1
⁄4 1
/2 17/8 415/16 27/16 0.45 300
3 3.125 1
⁄4 1
/2 21/8 51/2 41/16 0.66 300
4 4.125 1
⁄4 1
/2 25/8 65/8 51/16 0.75 300
NOTE: Sizes 1/4”, 3/8”, 21/2”, 3” and 4” are only available in hinged style, with
the exception of stainless steel which is only available in two-screw style
regardless of size.
FIG. 105 Hanger Flange
SERVICE: For attaching hanger rod to wood beams, ceilings, walls or floors.
MATERIAL: Malleable Iron or 304 Stainless Steel
FINISH: Black, Electro-Galvanized or Copper Epoxy Coated (COPPER-GARD)
ORDERING: Specify figure number, rod size, material and finish.
ROD SIZE SCREW SIZE WEIGHT
B C D E
A F EACH, LBS.
3
/8 - 16 13/8 23/4 7
/16 111/16 #12 0.18
1
/2 - 13 13/8 23/4 7
/16 111/16 #12 0.18
NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805

6
FIG. 110 Adjustable Swivel Ring Hanger
SERVICE: For suspension of non-insulated, stationary piping and copper tubing services.
Approved for use without additional locking nuts normally required with pipe hangers.
MATERIAL: Carbon Steel
FINISH: Electro-Galvanized, Copper Plated or Copper Epoxy Coated (COPPER-GARD)
APPROVALS: FM (NFPA 21/2” - 8”, IPC 3/4” - 8”), UL (NFPA 21/2” - 8”, IPC 3/4” - 8”)
ORDERING: Specify figure number, pipe/tube size and finish.
SPRINKLER SERVICE HANGER
PIPE NFPA STOCK WEIGHT MAX. REC.
A B C D E
SIZE ROD SIZE SIZE EACH, LBS. LOAD, LBS.
/2
1 3
/8 15/8 7
/8 13/16 21/2 27/8 18ga x 5/8 0.08 400
/4
3 3
/8 19/16 7
/8 11/16 27/16 215/16 18ga x 5/8 0.08 400
1 3
/8 13/4 7
/8 11/16 25/8 31/4 18ga x 5/8 0.08 600
11/4 3
/8 111/16 7
/8 7
/8 29/16 33/8 18ga x 5/8 0.10 600
11/2 3
/8 113/16 7
/8 7
/8 211/16 35/8 18ga x 5/8 0.10 600
2 3
/8 21/2 7
/8 15/16 33/8 41/2 18ga x 5/8 0.12 600
21/2 3
/8 31/8 7
/8 13/8 37/8 53/8 14ga x 3/4 0.24 600
3 3
/8 35/8 7
/8 15/8 41/2 61/4 14ga x 3/4 0.28 600
31/2 3
/8 4 7
/8 13/4 47/8 67/8 14ga x 3/4 0.32 600
4 3
/8 41/8 7
/8 15/8 5 71/4 14ga x 3/4 0.32 1000
5 1
/2 41/4 11/16 17/8 53/4 81/2 13ga x 3/4 0.62 1000
6 1
/2 51/8 11/16 21/8 63/4 101/8 12ga x 3/4 0.65 1250
8 1
/2 7 11/16 23/8 77/8 121/4 11ga x 1 1.00 1250
NOTE: In accordance with the National Fire Protection Association (NFPA 13)
PLUMBING SERVICE HANGER
PIPE ROD STOCK WEIGHT MAX. REC.
A B C D E
SIZE SIZE SIZE EACH, LBS. LOAD, LBS.
/2
1 3
/8 15/8 7
/8 13/16 21/2 27/8 18ga x 5/8 0.08 400
/4
3 3
/8 19/16 7
/8 11/16 27/16 215/16 18ga x 5/8 0.08 400
1 3
/8 13/4 7
/8 11/16 25/8 31/4 18ga x 5/8 0.08 600
11/4 3
/8 111/16 7
/8 7
/8 29/16 33/8 18ga x 5/8 0.10 600
11/2 3
/8 113/16 7
/8 7
/8 211/16 35/8 18ga x 5/8 0.10 600
2 3
/8 21/2 7
/8 15/16 33/8 41/2 18ga x 5/8 0.12 600
21/2 1
/2 23/4 11/16 11/4 311/16 51/8 14ga x 3/4 0.32 600
3 1
/2 31/8 11/16 11/8 4 57/8 14ga x 3/4 0.35 600
31/2 1
/2 35/8 11/16 11/2 45/16 65/8 14ga x 3/4 0.39 600
4 5
/8 37/8 11/8 11/4 415/16 71/8 13ga x 3/4 0.43 1000
5 5
/8 43/8 11/8 13/8 55/8 81/2 12ga x 1 0.65 1000
6 3
/4 55/16 13/8 2 611/16 101/8 12ga x 1 1.09 1250
8 3
/4 615/16 13/8 25/8 85/16 127/8 11ga x 1 1.24 1250
NOTE: In accordance with the International Plumbing Code (IPC)
COPPER TUBING HANGER
TUBE TUBE ROD STOCK WEIGHT MAX REC.
A B C D E
SIZE OD SIZE SIZE EACH, LBS. LOAD, LBS.
/2
1
0.625 3
/8 113/16 /8
7
11/2 211/16 3 18ga x 5/8 0.07 300
/4
3
0.875 3
/8 15/8 /8
7
13/16 21/2 215/16 18ga x 5/8 0.07 300
1 1.125 3
/8 19/16 7
/8 1 27/16 3 18ga x 5/8 0.07 300
11/4 1.375 3
/8 15/8 7
/8 15
/16 21/2 33/16 18ga x 5/8 0.08 300
11/2 1.625 3
/8 111/16 7
/8 7
/8 29/16 33/8 18ga x 5/8 0.09 300
2 2.125 3
/8 27/16 7
/8 1 /8 35/16
3
43/8 18ga x 5/8 0.10 300
21/2 2.625 1
/2 213/16 11/16 11/2 37/8 59/16 14ga x 1 0.31 525
3 3.125 1
/2 31/8 11/16 19/16 43/16 53/4 14ga x 1 0.35 525
31/2 3.625 1
/2 31/2 11/16 111/16 49/16 63/8 14ga x 1 0.38 525
4 4.125 1
/2 33/4 11/16 111/16 413/16 615/16 14ga x 1 0.41 650
5 5.125 1
/2 41/8 11/16 19/16 53/16 713/16 14ga x 1 0.48 1000
6 6.125 1
/2 45/8 11/16 19/16 511/16 815/16 14ga x 1 0.53 1000
NOTE: In accordance with ASTM B88
7
FIG. 136 Hold Down Strap

FIG. 137 Hold Down Strap for DI Pipe
SERVICE: To hold horizontally and vertically oriented piping against the attached
structure. Prevents lateral movement.
MATERIAL: Carbon Steel or 304/316 Stainless Steel
FINISH: Black, Electro-Galvanized or Hot-Dip Galvanized
ORDERING: Specify figure number, pipe size, material and finish.
FIG. #136
PIPE STOCK SIZE WEIGHT
A B D H L
SIZE G EACH, LBS.
3 7 31/2 /43 1
/4 x 11/2 7
/16 13/4 1.3
31/2 7 /2
1
4 /43 1
/4 x 11/2 7
/16 2 1.4
4 8 41/2 3
/4 1
/4 x 11/2 7
/16 21/4 1.6
5 91/16 59/16 3
/4 1
/4 x 11/2 7
/16 213/16 1.9
6 111/8 65/8 1 1
/4 x 2 9
/16 35/16 3.0
8 131/8 85/8 1 1
/4 x 2 9
/16 45/16 3.7
10 151/4 103/4 1 1
/4 x 2 9
/16 53/8 4.5
12 171/4 123/4 1 1
/4 x 2 9
/16 63/8 5.2
14 183/4 14 1 3
/8 x 2 11
/16 7 8.5
16 203/4 16 1 3
/8 x 2 11
/16 8 9.6
18 223/4 18 1 3
/8 x 2 11
/16 9 10.7
20 243/4 20 1 3
/8 x 2 11
/16 10 11.8
24 303/4 24 11/2 3
/8 x 3 13
/16 12 21.6
FIG. #137
DI PIPE STOCK SIZE WEIGHT
A B D H L
SIZE G EACH, LBS.
3 71/2 315/16 3/4 1
/4 x 11/2 7
/16 2 1.4
4 85/16 413/16 3/4 1
/4 x 11/2 7
/16 27⁄16 1.7
6 117/16 67⁄8 1 1
/4 x 2 9
/16 37⁄16 3.1
8 139/16 91⁄6 1 1
/4 x 2 9
/16 49⁄16 3.9
10 155/8 111⁄8 1 1
/4 x 2 9
/16 59⁄16 4.6
12 173/4 133/16 1 1
/4 x 2 9
/16 65⁄8 5.4
14 201/16 155/16 1 3
/8 x 2 11
/16 711⁄16 9.2
16 223/16 173⁄8 1 3
/8 x 2 11
/16 811⁄16 10.4
18 241/4 191⁄2 1 3
/8 x 2 11
/16 93⁄4 11.5
20 267/16 215⁄8 1 3
/8 x 2 11
/16 1013/16 12.7
24 329/16 2513/16 11/2 3
/8 x 3 13
/16 1215/16 23.1
FIG. 155 Offset Return Line J-Hook
SERVICE: For general piping running next to a wall.

FINISH: Black or Electro-Galvanized
ORDERING: Specify figure number, pipe size and finish.
PIPE STOCK SIZE WEIGHT MAX. REC.
C H L E
SIZE S EACH, LBS. LOAD, LBS.
3 3 9
/16 73/4 5 /4 x 11/2
1
1.39 600
4 31/2 9
/16 81/4 5 /4 x 11/2
1
1.58 600
6 411/16 9
/16 11 7 1
/4 x 2 2.80 700

8
FIG. 165 U-Bolt

FIG. 166 U-Bolt for DI Pipe
SERVICE: For support, anchor or guide of heavy loads.

ORDERING: Specify figure number, pipe size, material and finish. (Each FIG. #165
U-Bolt is furnished with four FIG. #785 Hex Nuts. Each FIG. #166 U-Bolt
is furnished with four FIG. #790 Hex Nuts.)
FIG. #165
PIPE WEIGHT MAX. REC.
A B C T
SIZE EACH, LBS. LOAD, LBS.
/2
1 1
/4 23/4 13/16 23/8 0.11 485
/4
3 1
/4 23/4 13/8 23/8 0.12 485
1 1
/4 23/4 15/8 23/8 0.12 485
11/4 3
/8 27/8 21/16 23/8 0.28 1220
11/2 3
/8 3 23/8 21/2 0.30 1220
2 3
/8 31/4 213/16 21/2 0.33 1220
21/2 1
/2 33/4 37/16 3 0.73 2260
3 1
/2 4 41/16 3 0.78 2260
31/2 1
/2 41/4 49/16 3 0.84 2260
4 1
/2 41/2 51/16 3 0.90 2260
5 1
/2 5 61/8 3 1.01 2260
6 5
/8 61/8 73/8 33/4 1.97 3620
8 5
/8 71/8 93/8 33/4 2.33 3620
10 3
/4 83/8 115/8 4 4.91 5420
12 7
/8 95/8 133/4 41/4 7.73 7540
14 7
/8 101/4 15 41/4 8.28 7540
16 7
/8 111/4 17 41/4 9.15 7540
18 1 125/8 191/8 43/4 13.48 9920
20 1 135/8 211/8 43/4 14.57 9920
24 1 155/8 251/8 43/4 16.87 9920
30 1 185/8 311/8 43/4 19.00 9920
FIG. #166
DI PIPE WEIGHT MAX. REC.
A B C T
3 1
/2 41/4 45/8 31/4 0.84 2260
4 1
/2 43/4 57/16 31/4 1.06 2260
6 5
/8 61/4 73/4 4 2.23 3620
8 5
/8 73/8 97/8 4 2.60 3620
10 3
/4 85/8 12 41/4 4.49 5420
12 7
/8 97/8 141/4 41/2 7.15 7540
14 7
/8 11 163/8 5 8.10 7540
16 7
/8 12 181/2 5 9.00 7540
18 1 133/8 205/8 51/2 13.20 9920
20 1 141/2 223/4 55/8 14.40 9920
24 1 165/8 27 53/4 16.80 9920
30 1 195/8 331/4 6 22.00 9920

9
FIG. 200 Adjustable Clevis Hanger
SERVICE: For the suspension of non-insulated, stationary piping and copper tubing
services.
FINISH: Black, Electro-Galvanized, Hot-Dip Galvanized, Copper Plated or Copper
Epoxy Coated (COPPER-GARD)
STANDARDS: MSS SP-58 Type 1, FS WW-H-171E Type 1 (NPS) and Type 12 (copper tube)
APPROVALS: FM (NPS 3/4” - 8” excluding 7” and Stainless Steel), UL (NPS 21/2” - 8” excluding
7”)
ORDERING: Specify figure number, pipe/tube size, material and finish. (Clevis Hangers
for 20” pipe and larger are furnished with a cross rod spacer.)
A B C E F BOLT
SIZE TOP BOTTOM EACH, LBS. LOAD, LBS.
/2
1 3
/8 13ga x 7/8 13ga x 7/8 111/16 21/16 15
/16 7
/16 1
/4 0.18 610
/4
3 3
/8 13ga x 7/8 13ga x 7/8 111/16 29/16 15
/16 7
/16 1
/4 0.18 610
1 3
/8 13ga x 7/8 13ga x 7/8 21/16 211/16 11/4 5
/8 1
/4 0.22 610
11/4 3
/8 13ga x 7/8 13ga x 7/8 21/2 33/16 111/16 7
/8 1
/4 0.26 610
11/2 3
/8 12ga x 7/8 12ga x 7/8 27/8 311/16 21/16 11/16 1
/4 0.34 610
2 3
/8 12ga x 7/8 12ga x 7/8 35/16 47/16 21/2 11/4 1
/4 0.38 610
21/2 1
/2 9ga x 13/16 10ga x 13/16 41/2 57/8 33/8 115/16 5
/16 0.86 1130
3 1
/2 9ga x 13/16 10ga x 13/16 43/4 61/2 311/16 13/4 5
/16 0.96 1130
31/2 1
/2 8ga x 13/16 10ga x 13/16 57/8 715/16 413/16 29/16 5
/16 1.14 1130
4 5
/8 8ga x 13/16 10ga x 13/16 515/16 83/16 49/16 21/8 3
/8 1.26 1430
5 5
/8 4ga x 11/4 8ga x 11/4 511/16 87/16 45/16 17/16 1
/2 2.04 1430
6 3
/4 3ga x 11/2 8ga x 11/2 613/16 101/8 53/16 13/4 1
/2 2.80 1940
7 3
/4 3ga x 11/2 8ga x 11/2 713/16 115/8 63/16 2 1
/2 3.24 2000
8 3
/4 3ga x 13/4 8ga x 13/4 81/16 127/16 61/4 17/8 5
/8 4.46 2000
10 7
/8 3
/8 x 13/4 3ga x 13/4 10 157/16 8 21/4 3
/4 8.06 3600
12 7
/8 3
/8 x 2 3ga x 2 119/16 18 99/16 213/16 3
/4 10.34 3800
14 1 1
/2 x 2 1
/4 x 2 129/16 199/16 109/16 29/16 7
/8 14.37 4200
16 1 1
/2 x 21/2 1
/4 x 21/2 1315/16 2115/16 1115/16 213/16 1 20.56 4600
18 1 1
/2 x 21/2 1
/4 x 21/2 16 25 137/8 33/4 1 23.07 4800
20 11/4 5
/8 x 3 3
/8 x 3 171/2 271/2 151/8 33/4 11/4 47.13 4800
24 11/4 5
/8 x 3 3
/8 x 3 193/4 313/4 173/8 4 11/4 54.00 4800
30 11/4 3
/4 x 3 3
/8 x 3 241/8 391/8 211/2 43/4 11/4 69.00 6000
TUBE TUBE STOCK SIZE WEIGHT MAX REC.
A B C E F BOLT
SIZE OD TOP BOTTOM EACH, LBS. LOAD, LBS.
/2
1
0.625 3
/8 18ga x 7/8 18ga x 7/8 17/8 23/16 11/8 /21 1
/4 0.12 150
/4
3
0.875 3
/8 18ga x 7/8 18ga x 7/8 13/4 21/8 1 /21 1
/4 0.12 250
1 1.125 3
/8 18ga x 7/8 18ga x 7/8 113/16 25/16 11/16 1
/2 1
/4 0.12 250
11/4 1.375 3
/8 18ga x 7/8 18ga x 7/8 21/8 23/4 15/16 3
/4 1
/4 0.12 250
11/2 1.625 3
/8 18ga x 7/8 18ga x 7/8 21/2 31/4 13/4 15
/16 1
/4 0.18 250
2 2.125 3
/8 14ga x 7/8 16ga x 7/8 215/16 4 23/16 11/16 1
/4 0.24 250
21/2 2.625 1
/2 12ga x 13/16 14ga x 13/16 47/8 53/4 33/8 21/16 1
/4 0.58 350
3 3.125 1
/2 12ga x 13/16 14ga x 13/16 41/2 61/8 37/16 2 1
/4 0.60 350
4 4.125 1
/2 11ga x 13/16 14ga x 13/16 57/8 77/8 43/4 29/16 5
/16 1.02 400
5 5.125 5
/8 8ga x 11/4 8ga x 11/4 57/8 83/4 43/4 15/8 3
/8 1.68 550
6 6.125 5
/8 8ga x 11/4 8ga x 11/4 61/16 9 43/4 11/2 3
/8 1.84 550

10
FIG. 200 Adjustable Clevis Hanger, PVC
SERVICE: For the suspension of stationary brass, aluminum and glass piping services, and
copper tubing services. Plastic coating prevents pipe/tube from coming in
contact with the hanger.
FINISH: Clevis top, bolt and nut are Electro-Galvanized, clevis bottom is plastic coated.
A B C E F BOLT
/2
1 3
/8 18ga x 7/8 18ga x 7/8 13/4 21/8 1 1
/2 1
/4 0.12 150
/4
3 3
/8 18ga x 7/8 18ga x 7/8 113/16 25/16 11/16 1
/2 1
/4 0.12 250
1 3
/8 18ga x 7/8 18ga x 7/8 21/8 23/4 15/16 3
/4 1
/4 0.12 250
11/4 3
/8 18ga x 7/8 18ga x 7/8 21/2 31/4 13/4 15/16 1
/4 0.18 250
11/2 3
/8 14ga x 7/8 16ga x 7/8 213/16 313/16 21/16 11/8 1
/4 0.24 250
2 3
/8 14ga x 7/8 16ga x 7/8 35/16 41/2 29/16 11/4 1
/4 0.26 250
21/2 1
/2 12ga x 13/16 14ga x 13/16 41/2 55/16 37/16 21/16 1
/4 0.58 350
3 1
/2 12ga x 13/16 14ga x 13/16 413/16 69/16 33/4 17/8 5
/16 0.66 350
4 1
/2 11ga x 13/16 14ga x 13/16 61/16 85/16 5 23/8 3
/8 0.94 400
5 5
/8 4ga x 11/4 8ga x 11/4 511/16 87/16 45/16 17/16 1
/2 2.04 1430
6 3
/4 3ga x 11/2 8ga x 11/2 613/16 101/8 53/16 13/4 1
/2 2.80 1940
7 3
/4 3ga x 11/2 8ga x 11/2 713/16 115/8 63/16 2 1
/2 3.24 2000
8 3
/4 3ga x 13/4 8ga x 13/4 81/16 127/16 61/4 17/8 5
/8 4.46 2000
10 7
/8 3
/8 x 13/4 3ga x 13/4 10 157/16 8 21/4 3
/4 8.06 3600
12 7
/8 3
/8 x 2 3ga x 2 119/16 18 99/16 213/16 3
/4 10.34 3800
FIG. 205 Flat Top Clevis Hanger
SERVICE: For suspension of non-insulated, stationary piping services where space does
not permit installation of a standard FIG. #200 Adjustable Clevis Hanger.
FINISH: Electro-Galvanized
STANDARDS: MSS SP-58 Type 1
ORDERING: Specify figure number and pipe size.
A B C E F BOLT
2 3
/8 8ga x 1 12ga x 7/8 21/2 311/16 111/16 7
/16 /41
0.46 300
21/2 1
/2 8ga x 11/4 10ga x 13/16 27/8 43/16 113/16 7
/16 5
/16 0.78 500
3 1
/2 8ga x 11/4 10ga x 13/16 35/8 53/8 29/16 11
/16 5
/16 0.98 500
4 5
/8 4ga x 11/4 10ga x 13/16 41/16 65/16 211/16 3
/16 3
/8 1.38 700
5 5
/8 4ga x 11/4 8ga x 11/4 47/8 75/8 31/2 5
/8 1
/2 2.08 700
6 3
/4 3ga x 11/2 8ga x 11/2 51/2 87/8 37/8 7
/16 1
/2 2.82 900
8 3
/4 3ga x 13/4 8ga x 13/4 63/8 107/8 45/8 5
/16 5
/8 4.34 1000

11
FIG. 210 Adjustable Clevis Hanger w/ Extended Bottom
SERVICE: For the suspension of insulated, stationary piping services.

A B C E F BOLT
/2
1 3
/8 13ga x 7/8 12ga x 7/8 313/16 41/4 3 7
/16 1
/4 0.30 610
/4
3 3
/8 13ga x 7/8 12ga x 7/8 33/4 43/16 2 /16
15 7
/16 1
/4 0.33 610
1 3
/8 13ga x 7/8 12ga x 7/8 41/8 43/4 35/16 5
/8 1
/4 0.34 610
11/4 3
/8 13ga x 7/8 12ga x 7/8 4 /16 51/4
7
35/8 7
/8 1
/4 0.39 610
11/2 3
/8 12ga x 7/8 12ga x 7/8 43/4 53/4 315/16 11/16 1
/4 0.47 610
2 3
/8 12ga x 7/8 12ga x 7/8 7 /4 87/16
1
67/16 11/4 1
/4 0.65 610
21/2 1
/2 9ga x 13/16 10ga x 13/16 813/16 103/16 73/4 115/16 5
/16 1.24 1130
3 1
/2 9ga x 13/16 10ga x 13/16 9 103/4 715/16 13/4 5
/16 1.34 1130
4 5
/8 8ga x 13/16 10ga x 13/16 10 /8 123/8
1
813/16 21/8 3
/8 1.92 1430
5 5
/8 4ga x 11/4 8ga x 11/4 97/8 129/16 87/16 17/16 1
/2 2.58 1430
6 3
/4 3ga x 11/2 8ga x 11/2 107/8 141/8 91/4 13/4 1
/2 3.36 1940
8 3
/4 3ga x 13/4 8ga x 13/4 121/4 169/16 10 /16 17/8
7 5
/8 5.08 2000
10 7
/8 3
/8 x 13/4 3ga x 13/4 141/2 197/8 121/2 21/4 3
/4 9.08 3600
12 7
/8 3
/8 x 2 3ga x 2 157/8 221/4 137/8 213/16 3
/4 11.54 3800
FIG. 215 Adjustable Clevis Hanger for DI Pipe
SERVICE: For the suspension of non-insulated, stationary ductile iron piping services.
FINISH: Black or Hot-Dip Galvanized
DI PIPE STOCK SIZE WEIGHT MAX. REC.
A B C E F BOLT
4 /8
5
8ga x 13/16 10ga x 13/16 6 81/2 45/8 21/8 3
/8 1.32 1430
6 /4
3
3ga x 11/2 8ga x 11/2 6 /16
13
101/8 5 /16 13/4
3 1
/2 2.86 1940
8 3
/4 3ga x 13/4 8ga x 13/4 85/16 13 67/8 17/8 5
/8 4.56 2000
10 7
/8 3
/8 x 13/4 3ga x 13/4 101/2 161/4 8 /2
1
21/4 3
/4 8.70 3600
12 7
/8 3
/8 x 2 3ga x 2 113/4 183/4 9 /4 213/16
3 3
/4 11.08 3800
14 1 1
/2 x 21/2 1
/4 x 21/2 1315/16 2115/16 1115/16 213/16 1 22.70 4200
16 1 1
/2 x 2 /2
1 1
/4 x 21/2 151/4 25 131/2 33/8 1 25.38 4600
18 1 5
/8 x 3 3
/8 x 3 171/2 271/2 151/8 33/4 11/4 47.00 4800
20 11/4 5
/8 x 3 3
/8 x 3 181/2 291/2 163/8 33/4 11/4 50.50 4800
24 11/4 5
/8 x 3 3
/8 x 3 203/4 34 185/8 4 11/4 58.00 4800
30 11/4 3
/4 x 3 3
/8 x 3 265/8 43 24 53/16 11/4 75.00 6000

12
FIG. 220 Clevis Hanger w/ Welded Shield

FIG. 221 Clevis Hanger w/ Welded MSS Shield
SERVICE: For vapor sealed lines.

ORDERING: Specify figure number, pipe size, insulation thickness, material and finish.
(FIG. #220 is supplied with a FIG. #300 Pipe Covering Protection Shield. FIG.
#221 is supplied with a FIG. #307 MSS Pipe Covering Protection Shield.)
HANGER SIZE SELECTION GUIDE
PIPE THICKNESS OF PIPE INSULATION
SIZE 1
/2” 1” 11/2” 2” 21/2” 3”
/2
1
11/2 21/2 31/2 5 6 7
3
/4 2 3 31/2 5 6 7
1 2 3 4 5 6 7
11/4 21/2 31/2 4 5 6 7
11/2 21/2 31/2 5 6 7 8
2 3 4 5 6 7 8
21/2 31/2 5 6 7 8 10
3 4 5 6 7 8 10
31/2 5 6 7 8 10 10
4 5 6 7 8 10 10
5 6 7 8 10 10 12
6 7 8 10 10 12 12
8 10 10 12 12 14 16
10 12 12 14 16 16 18
12 14 16 16 18 18 20
14 16 16 18 18 20 20
16 18 18 20 20 24 24
FIG. 230 V-Bottom Adjustable Clevis Hanger
SERVICE: For the suspension of flexible pipe, tubing or hose. Hanger must be used
in conjunction with FIG. #235 V-Channel. V-Channel must be cut to allow
installation of fittings and couplings. FIG. #230 V-Bottom Adjustable
Clevis Hangers must be installed at the end of the run of V-channel.
Vertical adjustment of the supporting system is provided by the clevis top.
Upper nut must be tightened after the piping system is leveled.
ORDERING: Specify figure number and pipe size. (FIG. #235 V-Channel must be
ordered separately.)
SIZE PIPE BOLT STOCK SIZE WEIGHT MAX. REC.
A B C D E
NO. SIZE TOP BOTTOM EACH, LBS. LOAD, LBS.
1
/2 1
/4 14ga x 7/8 16ga x 7/8 3
/8 57/8 53/16 11/4 47/16 0.30 150
3
/4 1
/4 14ga x 7/8 16ga x 7/8 3
/8 57/8 5 11/4 41/4 0.30 150
1 1
/4 14ga x 7/8 16ga x 7/8 3
/8 57/8 47/8 11/4 41/16 0.30 150
1
11/4 1
/4 14ga x 7/8 16ga x 7/8 3
/8 57/8 45/8 11/4 37/8 0.30 150
11/2 1
/4 14ga x 7/8 16ga x 7/8 3
/8 57/8 47/16 11/4 311/16 0.30 150
2 1
/4 14ga x 7/8 16ga x 7/8 3
/8 57/8 41/8 11/4 33/8 0.30 150
21/2 3
/8 11ga x 13/16 14ga x 13/16 1
/2 815/16 613/16 23/8 53/4 0.96 250
2 3 3
/8 11ga x 13/16 14ga x 13/16 1
/2 815/16 63/8 23/8 55/16 0.96 250
4 3
/8 11ga x 13/16 14ga x 13/16 1
/2 815/16 511/16 23/8 41/2 0.96 250

13
FIG. 235 V-Channel
SERVICE: For the suspension of flexible pipe, tubing or hose. Channel must
be used in conjunction with FIG. #230 V-Bottom Adjustable Clevis
Hangers. Pipe is laid directly into the V-Channel and where
necessary, the V-Channel may be cut to allow for fittings or
couplings. Where practical, the hangers should be placed as close
to the V-Channel joint as possible.
FINISH: Pre-Galvanized
MAX TEMP: Maximum 450°F (Determined by type of pipe supported)
ORDERING: Specify figure number and channel number. (FIG. #230 V-Bottom
Adjustable Clevis Hangers must be ordered separately.)
CHANNEL PIPE STEEL WEIGHT MAX. REC.
A B
NO. SIZE THICKNESS EACH, LBS. LOAD, LBS.
1 1
/2 to 2 120 11/2 18ga 5.4 150
2 21/2 to 4 120 3 18ga 10.8 250
B
A
FIG. 245 Roller Chair
SERVICE: For use on lines subject to horizontal movement.

MATERIAL: Carbon Steel frame with Cast Iron roll or 304/316 Stainless
Steel frame with 304 Stainless Steel roll
B C D L
2 11/2 11/2 11/4 7
/16 1
/4 x 11/4 1.06 390
3 21/4 13/4 2 7
/16 1
/4 x 11/4 1.50 390
4 27/8 21/4 2 9
/16 3
/8 x 11/2 2.88 950
5 33/8 21/2 21/2 9
/16 3
/8 x 11/2 3.50 950
6 37/8 23/4 31/4 9
/16 3
/8 x 2 5.50 950
7 41/2 27/8 31/2 9
/16 3
/8 x 2 7.00 1350
8 51/8 3 4 11
/16 3
/8 x 2 7.31 1350
10 63/8 35/8 5 11
/16 1
/2 x 2 12.44 1730
12 71/2 41/8 6 11
/16 1
/2 x 2 16.50 2400
14 83/8 411/16 61/2 13
/16 1
/2 x 21/2 24.50 3130
16 93/8 53/8 81/4 13
/16 1
/2 x 3 34.50 3970
18 107/16 6 91/4 13
/16 1
/2 x 3 36.50 4200
20 115/8 61/2 101/4 13
/16 1
/2 x 3 45.00 4550
24 14 77/8 121/4 15
/16 5
/8 x 4 77.50 6160
30 1715/16 83/4 153/8 15
/16 5
/8 x 4 110.00 7290

14
FIG. 248 Pipe Roller Stand

PIPE DIA. DIA. WEIGHT MAX. REC.
A B C D E H J
SIZE F G EACH, LBS. LOAD, LBS.
2 13/4 83/8 6 4 311/16 9/16 1 33/8 63/8 5.08 390
21/2 13/4 83/8 6 4 315/16 9/16 1 33/8 63/8 5.08 390
3 13/4 83/8 6 4 41/4 9/16 1 33/8 63/8 5.08 390
31/2 13/4 83/8 6 4 41/2 9/16 1 33/8 63/8 5.08 390
4 2 97/8 6 41/4 5 9
/16 1 43/4 77/8 6.31 950
5 2 97/8 6 41/4 5 /16 9/16
9
1 43/4 77/8 6.31 950
6 2 97/8 6 41/4 61/16 9/16 1 43/4 77/8 6.31 950
8 33/8 85/8 8 5 813/16 11/16 1 7 4 13.65 2100
10 33/8 85/8 8 5 97/8 11/16 1 7 4 13.65 2100
12 37/8 11 8 6 117/16 13/16 1 9 53/4 21.00 3075
14 37/8 11 8 6 121/16 13/16 1 9 53/4 21.00 3075
16 41/4 123/8 10 61/2 135/8 13/16 1 103/8 63/4 34.23 4980
18 41/4 123/8 10 61/2 1411/16 13/16 1 103/8 63/4 34.23 4980
20 41/4 123/8 10 61/2 1511/16 13/16 1 103/8 63/4 34.23 4980 NOTE: “A” dimension is the center of axle to
24 43/8 131/2 10 61/2 1711/16 13/16 1 111/2 71/2 40.00 6100 bottom of plate. “E” dimension is the center
30 5 17 10 73/4 213/4 11/8 1 141/4 10 71.32 7500 of pipe to bottom of base plate.
36 53/4 20 12 9 253/4 15/8 1 17 12 147.00 12000

42 53/4 20 12 9 287/8 15/8 1 17 12 147.00 12000
FIG. 249 Adjustable Pipe Roller Stand

PIPE C C WEIGHT MAX. REC.
A B D E F G
SIZE MIN. MAX. EACH, LBS. LOAD, LBS.
2 67/8 61/2 43/4 55/8 37/8 1 1 /2
1
11.00 390
21/2 67/8 61/2 5 57/8 37/8 1 1 /2
1
11.00 390
3 67/8 61/2 55/16 63/16 37/8 1 1 1
/2 11.00 390
31/2 67/8 61/2 59/16 67/16 37/8 1 1 1
/2 11.00 390
4 81/2 6 63/16 77/16 51/8 1 1 1
/2 13.10 950
5 81/2 6 63/4 8 51/8 1 1 1
/2 13.10 950
6 81/2 6 71/4 81/2 51/8 1 1 1
/2 13.10 950
8 101/2 71/2 101/8 1111/16 73/8 1 1 3
/4 29.00 2100 F
10 101/2 71/2 113/16 123/4 73/8 1 1 3
/4 29.00 2100
12 121/2 81/2 123/4 141/8 91/2 1 1 7
/8 40.00 3075
14 121/2 81/2 133/8 143/4 91/2 1 1 7
/8 40.00 3075
16 145/8 11 153/8 171/4 111/8 1 1 11/8 63.84 4980 D
18 145/8 11 163/8 181/4 111/8 1 1 11/8 63.84 4980 A
20 145/8 11 173/8 191/4 111/8 1 1 11/8 63.84 4980 B
24 153/4 11 191/4 211/4 121/4 1 1 11/4 71.00 6100
NOTE: “C” dimension is the center of pipe to bottom
30 191/2 103/4 247/16 2611/16 153/4 1 11/2 13/4 125.28 7500 of base plate. “D” dimension is center to center of
36 23 123/4 2813/16 3013/16 19 11/8 2 2 214.4 12000 mounting holes in bottom plate. “E” dimension is
42 23 123/4 3115/16 3315/16 19 11/8 2 2 214.4 12000 the diameter of the mounting holes in botttom plate.

15
FIG. 250 Adjustable Roller Hanger
SERVICE: For suspension of pipe from a single support rod where horizontal movement
may occur due to expansion or contraction.
MATERIAL: Carbon Steel or 304/316 Stainless Steel yoke and cross bolt with Cast Iron or
304 Stainless Steel roll
A B C D E F L
3 1
/2 43/8 21/4 33/4 33/8 51/2 71/4 2.46 310
4 5
/8 43/4 23/4 47/8 33/4 61/2 81/2 3.21 475
5 5
/8 57/8 33/8 57/8 41/4 8 97/8 4.93 685
6 3
/4 57/8 4 7 41/4 9 113/8 6.26 780
7 3
/4 61/2 45/8 8 5 10 12 7.07 780
8 7
/8 71/4 51/8 9 51/2 12 133/4 11.63 780
10 7
/8 9 63/8 11 67/8 141/4 17 16.96 965
12 7
/8 9 /8 73/8
5
13 77/8 17 187/8 21.92 965
14 1 111/4 83/8 141/4 91/4 181/2 217/8 31.94 1200
16 1 121/4 93/8 161/4 101/4 20 241/8 44.78 1200
18 1 131/4 101/2 181/4 111/4 22 261/2 48.00 1400
20 11/4 141/4 115/8 201/4 121/4 24 281/8 62.00 1600
24 11/4 161/4 1311/16 241/4 141/4 30 327/16 109.00 1800
FIG. 260 Adjustable Two-Rod Roller Hanger
SERVICE: For suspension of pipe where longitudinal movement due to

expansion and contraction may occur.
MATERIAL: Carbon Steel or 304/316 Stainless Steel cross bolt with Cast Iron or
304 Stainless Steel roll and sockets
ORDERING: Specify figure number, pipe size, material and finish. (All dimensions
are subject to change without notice. Contact National Pipe Hanger
Corporation for critical installations.)
A B C E L
2 3
/8 15/8 41/8 33/16 51/4 0.57 600
21/2 1
/2 115/16 47/8 35/8 61/4 1.00 660
3 1
/2 21/4 51/2 315/16 67/8 1.38 700
31/2 1
/2 29/16 61/8 45/16 71/2 1.35 750
4 1
/2 213/16 63/4 413/16 81/4 1.79 750
5 5
/8 37/16 81/16 59/16 911/16 2.57 750
6 3
/4 4 99/16 61/2 117/16 4.25 1070
7 3
/4 411/16 103/4 613/16 121/2 5.11 1100
8 7
/8 51/8 1115/16 8 141/16 7.60 1350
10 7
/8 63/8 141/16 91/4 163/16 9.50 1730
12 7
/8 77/16 165/16 107/16 1715/16 12.50 2400
14 1 83/8 173/4 121/8 201/8 18.80 3130
16 1 97/16 209/16 1215/16 221/8 24.50 3970
18 1 101/2 217/8 141/4 241/2 26.50 4200
20 11/4 115/8 241/4 153/4 271/4 33.00 4550
24 11/2 14 285/8 183/4 321/8 54.00 6160
30 11/2 177/16 351/2 227/8 39 86.00 7290

16
FIG. 300 Pipe Covering Protection Shield

FIG. 302 Pipe Covering Protection Shield w/ 5⁄16” Hole
SERVICE: For use on the outside of foam or fiber glass insulation.

ORDERING: Specify figure number, shield size and material. (FIG. #816 plated
round head machine screws sold separately for use with the FIG.
#302 shield with 5/16” hole.)
SHIELD STOCK SIZE DIA. HANGER WEIGHT PER
LENGTH
SIZE NO. C “D” SIZE 100, LBS.
0 12 24ga 17/8 11/2 25
1 12 24ga 23/8 2 31
2 12 24ga 27/8 21/2 37
3 12 18ga 31/2 3 93
4 12 18ga 4 31/2 103
5 12 18ga 41/2 4 118
6 12 18ga 5 5 133
7 12 18ga 59/16 5 147
8 12 18ga 65/8 6 165
9 12 18ga 75/8 8 190
10 12 18ga 85/8 8 210
13 12 18ga 95/8 10 235
14 12 18ga 103/4 10 265
15 12 18ga 113/4 12 295
16 12 18ga 123/4 12 315
17 12 16ga 14 14 445
18 12 16ga 15 16 446
19 12 16ga 16 16 490
20 12 16ga 17 18 515
21 12 16ga 18 18 550
22 12 16ga 19 20 570
23 12 16ga 20 20 635 SHIELD SIZE SELECTION TABLE FOR PIPE
24 12 16ga 21 24 645 PIPE A - Insulation Thickness
25 12 16ga 22 24 660 SIZE 1
/2 /4
3
1 11/2 2
26 12 16ga 23 24 700 /2 1
0 1 - - -
27 12 16ga 24 24 785 3
/4 1 1 2 4 6
28 12 16ga 26 30 790 1 1 2 3 5 7
29 12 16ga 27 30 805 11/4 2 3 3 6 7
30 12 16ga 28 30 860 11/2 2 3 4 6 7
SHIELD SIZE SELECTION TABLE FOR TUBING 2 3 4 5 7 8
TUBING A - Insulation Thickness 21/2 4 5 6 7 8
SIZE /2
1
/4
3
1 11/2 2 3 5 6 7 8 9
1
/2 0 1 2 4 5 31/2 - - 8 9 10
3
/4 0 1 2 4 6 4 - - 8 9 10
1 1 2 3 4 6 5 - - 9 10 13
11/4 1 2 3 5 7 6 - - 10 13 14
11/2 2 3 3 5 7 8 - - 14 15 16
2 3 4 4 6 8 10 - - 16 17 18
21/2 4 5 5 7 8 12 - - 18 19 20
3 5 6 6 8 9 14 - - 19 20 21
31/2 6 7 7 8 9 16 - - 21 22 23
4 7 7 8 9 10 18 - - 23 24 25
5 8 8 9 10 13 20 - - 25 26 27
6 9 9 10 13 14 24 - - 28 29 30

17
FIG. 307 MSS Pipe Covering Protection Shield
SERVICE: For use on the outside of foam or fiberglass insulation.

STANDARDS: MSS SP-58 Type 40, FS WW-H171E Type 41
ORDERING: Specify figure number, shield size and material.
SHIELD STOCK SIZE DIA. HANGER WEIGHT PER
LENGTH
SIZE NO. C D SIZE 100, LBS.
0 12 18ga 17/8 11/2 53
1 12 18ga 23/8 2 68
2 12 18ga 27/8 21/2 82
3 12 18ga 31/2 3 93
4 12 18ga 4 31/2 103
5 12 18ga 41/2 4 118
6 12 18ga 5 5 133
7 12 18ga 59/16 5 147
8 12 16ga 65/8 6 233
9 12 16ga 75/8 7 266
10 12 16ga 85/8 8 300
11 18 16ga 75/8 7 399
12 18 16ga 85/8 8 449
13 18 16ga 95/8 10 503
14 18 16ga 103/4 10 562
15 24 14ga 113/4 12 1012
16 24 14ga 123/4 12 1094
17 24 14ga 14 14 1203
18 24 14ga 15 16 1292
19 24 14ga 16 16 1374
20 24 14ga 17 18 1463
21 24 12ga 18 18 2133
22 24 12ga 19 20 2256
23 24 12ga 20 20 2379 SHIELD SIZE SELECTION TABLE FOR PIPE
24 24 12ga 21 24 2492 PIPE A - Insulation Thickness
25 24 12ga 22 24 2615 SIZE 1
/2 /4
3
1 11/2 2
26 24 12ga 23 24 2737 /2 1
0 1 - - -
27 24 12ga 24 24 2851 3
/4 1 1 2 4 6
28 24 12ga 26 30 3087 1 1 2 3 5 7
29 24 12ga 27 30 3209 11/4 2 3 3 6 7
30 24 12ga 28 30 3322 11/2 2 3 4 6 7
SHIELD SIZE SELECTION TABLE FOR TUBING 2 3 4 5 7 8
TUBING A - Insulation Thickness 21/2 4 5 6 7 8
SIZE /2
1
/4
3
1 11/2 2 3 5 6 7 8 9
/2
1
0 1 2 4 5 31/2 - - 8 9 10
/4
3
0 1 2 4 6 4 - - 8 9 10
1 1 2 3 4 6 5 - - 9 10 13
11/4 1 2 3 5 7 6 - - 10 13 14
11/2 2 3 3 5 7 8 - - 14 15 16
2 3 4 4 6 8 10 - - 16 17 18
21/2 4 5 5 7 8 12 - - 18 19 20
3 5 6 6 8 9 14 - - 19 20 21
31/2 6 7 7 8 9 16 - - 21 22 23
4 7 7 8 9 10 18 - - 23 24 25
5 8 8 9 10 13 20 - - 25 26 27
6 9 9 10 13 14 24 - - 28 29 30

18
FIG. 310 Pipe Covering Protection Saddle

1 INCH
SERVICE: For suspension of insulated pipe where heat losses are to be
FIG. 315 kept to a minimum.
11⁄2 INCH MATERIAL: Carbon Steel or 304/316 Stainless Steel
FIG. 320 STANDARDS: MSS SP-58 Type 39, FS WW-H-171E Type 40A & Type 40B
2 INCH ORDERING: Specify figure number, pipe size, insulation size, material and
finish. (All saddles are 12” long.)
FIG. 325
PIPE FIG. ACTUAL THICKNESS HANGER ROLLER SIZE WEIGHT MAX. REC.
C D
SIZE NO. OF COVERING FIG. #260 FIG. #250 EACH, LBS. LOAD, LBS.
2 ⁄2 INCH
1
3
/4 310 7
/8 2 21/2 19/16 115/16 0.93 1200
FIG. 330 3
/4 315 17/16 3 31/2 21/8 25/8 1.74 1200
3
/4 320 21/16 4 5 23/4 33/8 2.60 1200
3 INCH 1 310 11/16 21/2 3 113/16 21/4 0.93 1200
1 315 19/16 3 4 27/16 215/16 1.74 1200
FIG. 340
1 320 21/8 4 5 27/8 31/2 2.60 1200
4 INCH 11/4 310 7
/8 21/2 3 115/16 21/2 1.32 1200
11/4 315 15/8 31/2 5 29/16 31/8 1.82 1200
11/4 320 21/16 5 5 31/16 311/16 2.60 1200
11/2 310 1 3 31/2 21/8 25/8 1.32 1200
11/2 315 11/2 31/2 5 211/16 31/4 1.82 1200
11/2 320 25/16 5 6 37/16 41/8 2.75 1800
11/2 325 213/16 7 7 313/16 45/8 3.01 1800
2 310 11/16 31/2 4 27/16 3 1.34 1200
2 315 19/16 4 5 27/8 31/2 1.98 1200
2 320 21/8 5 6 311/16 43/8 2.80 1800
2 325 25/8 7 7 315/16 43/4 3.18 1800
2 330 31/8 8 8 411/16 51/2 3.97 1800
21/2 310 11/16 31/2 5 211/16 31/4 1.34 1200
21/2 315 17/8 5 6 33/4 41/8 1.98 1200
21/2 320 25/16 6 7 315/16 45/8 2.80 1800
21/2 325 27/8 7 7 47/16 51/4 3.20 1800
21/2 330 33/8 8 10 415/16 53/4 3.98 1800
3 310 1 4 5 215/16 31/2 1.48 1200
3 315 19/16 5 6 31/2 43/16 2.08 1800
3 320 21/16 7 7 41/8 47/8 2.90 1800
3 325 29/16 8 8 411/16 53/8 3.01 1800
3 330 31/16 10 10 5 515/16 4.49 1800
31/2 310 11/4 5 6 37/16 4 1.48 1200
31/2 315 113/16 7 7 4 411/16 2.08 1800
31/2 320 21/4 8 8 43/8 53/16 2.90 1800
31/2 325 23/4 8 10 413/16 53/4 3.43 1800
31/2 330 35/16 10 10 51/2 67/16 4.49 1800
4 310 11/16 5 6 39/16 43/16 1.58 1800
4 315 19/16 7 7 37/8 411/16 2.14 1800
4 320 21/16 8 8 411/16 51/2 2.95 1800
4 325 29/16 8 10 51/8 61/16 3.43 1800
4 330 31/16 10 10 59/16 61/2 4.49 1800
4 340 41/16 12 14 69/16 711/16 6.09 1800
5 310 1 7 7 41/8 413/16 2.68 1800
5 315 11/2 8 8 41/2 55/16 3.30 1800
5 320 2 8 10 415/16 57/8 3.45 1800
5 325 29/16 10 12 59/16 61/2 3.69 1800
5 330 31/16 10 12 61/8 71/16 4.49 1800
5 340 43/16 12 14 73/16 81/4 6.09 1800

19
FIG. 310 Pipe Covering Protection Saddle

1 INCH
PIPE FIG. ACTUAL THICKNESS HANGER ROLLER SIZE WEIGHT MAX. REC.
FIG. 315 SIZE NO. OF COVERING FIG. #260 FIG. #250
C D EACH, LBS. LOAD, LBS.
11⁄2 INCH 6 310 1 8 8 49/16 53/8 3.82 1800

6 315 11/2 8 10 51/16 57/8 4.28 1800
FIG. 320 6 320 2 10 10 51/2 61/2 5.40 1800
6 325 21/2 10 12 61/16 71/16 6.85 1800
2 INCH 6 330 3 12 12 69/16 75/8 7.69 1800
6 340 41/8 14 16 75/8 91/8 10.24 1800
FIG. 325 8 310 1 10 12 51/2 65/8 4.39 1800
21⁄2 INCH 8 315 11/2 10 12 6 71/8 5.82 1800
8 320 2 12 12 61/2 75/8 6.41 1800
FIG. 330 8 325 211/16 12 14 71/4 85/16 7.21 1800
8 330 31/8 14 16 75/8 91/8 9.14 1800
3 INCH 8 340 41/8 16 18 811/16 101/8 10.24 1800
10 310 1 12 14 63/4 713/16 4.93 1800
FIG. 340 10 315 19/16 12 14 71/4 85/16 6.66 1800
4 INCH 10 320 21/16 14 16 75/8 91/16 8.57 1800
10 325 29/16 14 16 83/16 95/8 8.91 1800
10 330 31/16 16 18 87/8 101/4 11.10 1800
10 340 41/16 18 20 911/16 115/16 14.10 1800
12 310 1 14 16 79/16 91/8 7.19 5000
12 315 11/2 14 16 81/16 95/8 7.61 5000
12 320 21/16 16 18 813/16 103/16 8.73 5000
12 325 25/8 16 18 91/8 1011/16 9.69 5000
12 330 31/16 18 20 911/16 115/16 11.38 5000
12 340 41/8 20 - 1013/16 123/8 14.20 5000
14 310 1 16 18 83/8 911/16 7.19 5000
14 315 11/2 16 18 87/8 103/16 7.67 5000
14 320 2 16 18 91/4 103/4 9.43 5000
14 325 21/2 18 20 93/4 115/16 9.69 5000
14 330 3 18 20 101/4 117/8 11.82 5000
14 340 4 20 - 117/16 131/8 18.48 7200
16 310 1 18 20 93/8 107/8 7.99 5000
16 315 11/2 18 20 97/8 113/8 8.35 5000
16 320 2 18 20 101/4 117/8 10.00 5000
16 325 21/2 20 - 107/8 127/16 14.62 7200
16 330 3 24 - 113/16 131/8 18.17 7200
16 340 4 24 - 125/16 143/16 21.80 7200
18 310 1 20 - 103/8 12 8.62 5000
18 315 11/2 20 - 107/8 121/2 8.92 5000
18 320 2 20 - 111/2 131/16 13.19 7200
18 325 21/2 24 - 12 1315/16 16.89 7200
18 330 3 24 - 125/16 141/4 18.20 7200
18 340 4 24 - 131/2 157/16 21.95 7200
20 310 1 24 - 111/4 133/16 9.26 7200
20 315 11/2 24 - 113/4 1311/16 13.76 7200
20 320 2 24 - 125/16 141/4 14.98 7200
20 325 21/2 24 - 127/8 1413/16 16.79 7200
20 330 3 24 - 131/2 151/2 18.40 7200
20 340 4 30 - 143/16 165/8 22.83 7200
24 310 1 30 - 131/8 159/16 10.70 7200
24 315 11/2 30 - 135/8 161/16 16.05 7200
24 320 2 30 - 143/16 165/8 17.62 7200
24 325 21/2 30 - 143/4 173/16 18.75 7200
24 330 3 30 - 153/8 1713/16 19.72 7200
24 340 4 30 - 169/16 19 23.14 7200

20
FIG. 400 Standard Steel Pipe Clamp
SERVICE: For suspension of non-insulated piping services.

Normally used with FIG. #740 Weldless Eyenut.
B C D F
1
/2 11/8 7
/16 111/16 5
/16 11ga x 1 0.27 500
3
/4 11/4 7
/16 113/16 5
/16 11ga x 1 0.30 500
1 17/16 7
/16 2 5
/16 11ga x 1 0.33 500
11/4 19/16 7
/16 21/8 5
/16 11ga x 1 0.36 500
11/2 13/4 1
/2 21/4 5
/16 11ga x 1 0.37 800
2 23/8 1
/2 215/16 1
/2 3ga x 1 1.04 1040
21/2 211/16 3
/4 31/4 1
/2 3ga x 1 1.19 1040
3 215/16 3
/4 31/2 1
/2 3ga x 1 1.27 1040
31/2 31/4 3
/4 313/16 1
/2 3ga x 1 1.43 1040
4 33/8 3
/4 41/16 5
/8 4ga x 11/4 1.94 1040
5 41/16 7
/8 43⁄4 5
/8 4ga x 11/4 2.20 1040
6 5 7
/8 57/8 3
/4 3
/8 x 11/2 5.28 1615
8 61/8 1 7 3
/4 3
/8 x 11/2 6.25 1615
10 77/16 1 89/16 7
/8 1
/2 x 2 12.98 2490
12 87/16 1 99/16 7
/8 1
/2 x 2 14.82 2490
14 91/4 11/8 105/8 7
/8 1
/2 x 21/2 20.00 2490
16 101/4 11/8 115/8 7
/8 1
/2 x 21/2 22.00 2490
18 115/8 11/4 13 1 5
/8 x 21/2 30.91 3060
20 123/4 13/8 141/8 11/8 5
/8 x 21/2 35.89 3060
24 151/4 15/8 167/8 11/4 5
/8 x 3 53.00 3060
30 19 2 211/8 13/4 3
/4 x 4 110.86 3500
FIG. 405 Heavy Duty Two-Bolt Pipe Clamp
SERVICE: For suspension of non-insulated, heavy duty piping services.

Normally used with FIG. #740 Weldless Eyenut
B C D F
3 31/8 1 4 3
/4 3
/8 x 2 4.43 3370
4 33/4 1 47/8 7
/8 3
/8 x 2 5.74 3515
5 43/8 1 51/2 7
/8 3
/8 x 2 6.55 3515
6 51/4 11/8 65/8 1 1
/2 x 21/2 12.40 4865
8 61/4 11/8 75/8 1 1
/2 x 21/2 14.54 4865
10 711/16 11/4 91/16 11/4 5
/8 x 21/2 23.45 6010
12 91/4 15/8 111/8 11/2 3
/4 x 3 40.98 8675
14 10 15/8 117/8 11/2 3
/4 x 4 56.00 9120
16 115/16 15/8 133/16 11/2 3
/4 x 4 62.00 9120
18 141/2 3 181/2 2 3
/4 x 6 129.00 13800
20 16 3 20 2 1x5 148.00 15300
24 181/2 31/4 23 2 1x6 200.00 16300
30 221/2 31/2 26 21⁄4 11/4 x 8 390.00 20500

21
FIG. 404 Heavy Duty Riser Clamp
SERVICE: To support vertical piping from hanger rods or structural members

such as beams and concrete slabs. Shear lugs field welded to pipe
wall transfer pipe load to riser clamp.
MATERIAL: Carbon Steel meeting ASTM: A36, A500 Gr B, A307 Gr A and A563 Gr A
Stainless Steel Type 304 and 316 meeting ASTM: A240, A312, F593 and F594
FINISH: Black or Hot-Dip Galvanized meeting ASTM A123
MAX TEMP: 650ºF for Black Carbon Steel and Stainless Steel
350ºF for Hot-Dip Galvanized Carbon Steel
ORDERING: Specify figure number, pipe size, material and finish. (Order installation
hardware separately.)
TxW A B C D L S R
2 /2 x 21/2
1
11/4 2 18 1
/2 22 3
/4 1
/2 16.00 900
21/2 /2 x 21/2
1
11/4 2 20 1
/2 24 3
/4 1
/2 18.00 900
3 5
/8 x 3 11/4 2 20 5
/8 24 1 5
/8 27.30 1500
4 3
/4 x 4 11/4 2 22 3
/4 26 11/4 3
/4 46.70 2200
5 3
/4 x 4 11/4 2 22 3
/4 26 11/4 3
/4 47.40 2200
6 3
/4 x 5 11/4 2 24 7
/8 28 11/2 3
/4 66.00 3000
8 3
/4 x 5 11/4 2 27 7
/8 31 11/2 3
/4 74.00 3000
10 1x6 15/8 3 30 11/4 36 21/4 1 141.00 5500
12 1x7 17/8 3 32 11/2 38 21/2 11/4 185.00 7800
14 1x7 17/8 3 34 11/2 40 21/2 11/4 195.00 7800
16 11/4 x 8 2 3 36 11/2 42 21/2 11/4 283.00 9000
18 11/4 x 8 2 3 39 11/2 45 21/2 11/4 302.00 9000
20 11/4 x 8 25/8 41/4 42 2 501/2 31/2 11/2 364.48 13500
24 11/4 x 8 25/8 41/4 45 2 531/2 31/2 11/2 391.00 13500
Notes:
1. Maximum recommended load on rigid support. Loads may be doubled when used with springs or other resilient devices.
2. Welding in accordance with AWS D1.1 for carbon steel and AWS D1.6 for stainless steel.
3. Local pipe wall stress due to welded shear lug attachment evaluation available upon request, provide: pipe material, pipe wall thickness,
operating pressure and temperature, and corrosion allowance.
4. Concrete bearing plate as necessary by others.
5. For special designs, contact factory with pipe size, material, load, operating temperature, C and L dimensions, finish and support type.

22
FIG. 410 Double Bolt Pipe Clamp
SERVICE: For suspension of insulated pipe lines. Normally used

with a FIG. #740 Weldless Eyenut.
B C D E F H
1
/2 1 5
/8 27/8 25/16 3
/8 19/16 8ga x 1 0.54 950
3
/4 11/16 5
/8 3 27/16 3
/8 15/8 8ga x 1 0.57 950
1 13/8 5
/8 33/16 25/8 3
/8 115/16 8ga x 1 0.61 950
11/4 11/2 5
/8 31/2 215/16 3
/8 21/16 8ga x 1 0.68 950
11/2 115/16 7
/8 411/16 313/16 5
/8 213/16 4ga x 11/4 1.72 1545
2 23/16 7
/8 59/16 411/16 5
/8 31/16 4ga x 11/4 1.93 1545
21/2 27/16 7
/8 67/16 59/16 5
/8 35/16 4ga x 11/4 2.12 1545
3 23/4 1 7 61/8 5
/8 35/8 4ga x 11/4 2.26 1545
31/2 27/8 1 71/4 63/8 5
/8 33/4 4ga x 11/4 2.37 1545
4 31/2 11/16 75/8 61/2 3
/4 41/2 3
/8 x 2 6.57 2500
5 4 11/16 81/8 7 3
/4 5 3
/8 x 2 7.17 2500
6 5 17/16 915/16 89/16 1 61/8 3
/8 x 21/2 11.53 2865
8 6 17/16 1015/16 99/16 1 71/8 3
/8 x 21/2 13.22 2865
10 71/2 17/16 12 105/8 1 87/8 1
/2 x 21/2 19.98 3240
12 81/2 17/16 13 115/8 1 97/8 1
/2 x 21/2 22.16 3240
14 93/8 2 145/16 1211/16 11/4 11 5
/8 x 3 36.38 4300
16 103/8 2 155/16 1311/16 11/4 12 5
/8 x 3 39.77 4300
18 113/8 2 165/16 1411/16 11/4 13 5
/8 x 3 43.00 4300
20 123/4 2 171/2 157/8 11/2 143/8 3
/4 x 3 59.00 5490
24 143/4 2 191/2 177/8 11/2 163/8 3
/4 x 3 66.00 4500
30 183/4 21/2 261/8 233/8 11/2 211/4 3
/4 x 5 134.0 7500
FIG. 415 Heavy Duty Double Bolt Pipe Clamp
SERVICE: For supporting pipe requiring up to 4” of insulation.

MAX TEMP: 750˚F
PIPE STOCK SIZE WEIGHT MAX. REC. LOAD, LBS.
B C D E F H
SIZE S EACH, LBS. 650°F 750°F
6 43/4 13/4 103/16 815/16 1 6 3
/8 x 21/2 12.0 3500 3125
8 6 2 113/8 101/8 11/8 71/4 1
/2 x 21/2 18.5 4800 4285
10 71/2 21/4 131/8 113/8 11/4 9 1
/2 x 4 34.0 5500 4910
12 85/8 21/2 145/16 129/16 11/2 103/8 5
/8 x 4 48.0 7000 6250
14 95/8 21/2 151/2 131/2 11/2 115/8 3
/4 x 4 61.0 9500 8485
16 107/8 3 171/8 147/8 13/4 131/8 3
/4 x 5 92.0 10000 8930
18 131/2 31/2 181/4 161/4 2 151/4 1x4 110.0 13800 12325
20 141/2 31/2 203/4 181/4 2 17 1x5 143.0 15300 13665
24 151/2 31/2 225/16 195/16 2 181/2 1x6 185.0 16300 14555
30 197/8 41/4 323/4 281/4 21/4 243/8 1x8 348.0 20500 -

23
FIG. 420 Riser Clamp
SERVICE: For support of vertical pipe/tube runs.

FINISH: Black, Electro-Galvanized, Hot-Dip Galvanized, Copper Plated,
Copper Epoxy Coated (Copper-Gard), or PVC coated (PVC coated
riser clamps are completely Plastic Coated with Electro-Galvanized
hardware.)
APPROVALS: UL (For standard pipe sizes 2” - 8”)
ORDERING: Specify figure number, pipe/tube size, material and finish.
PIPE STOCK BOLT WEIGHT MAX. REC.
A B
SIZE SIZE SIZE EACH, LBS. LOAD, LBS.
1
/2 85/8 21/8 8ga x 1 3
/8 x 11/2 0.88 220
3
/4 813/16 25/16 8ga x 1 3
/8 x 11/2 0.92 220
1 91/16 25/8 8ga x 1 3
/8 x 11/2 0.94 220
11/4 97/16 215/16 8ga x 1 3
/8 x 11/2 1.00 250
11/2 10 37/16 8ga x 1 3
/8 x 11/2 1.04 250
2 109/16 4 8ga x 1 3
/8 x 11/2 1.14 300
21/2 111/8 49/16 3ga x 1 3
/8 x 11/2 1.60 400
3 1113/16 51/4 3ga x 1 3
/8 x 11/2 1.70 500
4 135/8 65/8 3ga x 1 1
/2 x 11/2 2.20 750
5 141/8 75/8 3ga x 11/2 1
/2 x 13/4 3.40 1500
6 153/8 87/8 3ga x 11/2 1
/2 x 13/4 3.72 1600
8 181/2 121/2 3/8 x 11/2 5
/8 x 21/2 7.20 2500
10 203/4 143/4 3/8 x 2 5
/8 x 23/4 11.00 2500
12 223/4 163/4 1/2 x 2 5
/8 x 31/4 16.10 2700
14 24 18 1
/2 x 2 5
/8 x 31/4 17.00 2700
16 26 21 5
/8 x 21/2 3
/4 x 4 29.16 2900
18 28 23 5/8 x 21/2 3
/4 x 4 32.40 2900
20 30 25 5/8 x 21/2 3
/4 x 41/2 35.00 2900
24 36 291/4 5/8 x 21/2 7
/8 x 41/2 43.00 2900 PVC STOCK BOLT WEIGHT MAX. REC.
A B
30 42 353/4 3/4 x 4 1x5 95.00 3200 PIPE SIZE SIZE SIZE EACH, LBS. LOAD, LBS.
TUBE TUBE STOCK BOLT WEIGHT MAX REC. /2
1
85/8 21/8 8ga x 1 3
/8 x 11/2 0.88 220
A B /4 813/16 25/16 8ga x 1 /8 x 11/2 0.92 220
SIZE OD SIZE SIZE EACH, LBS. LOAD, LBS.
3 3
1
/2 /8
5
611/16 111/16 11ga x 1 /4 x 1
1
0.48 225 1 91/16 25/8 8ga x 1 3
/8 x 11/2 0.94 220
3
/4 /8
7
7 2 11ga x 1 /4 x 1
1
0.50 225 11/4 97/16 215/16 8ga x 1 3
/8 x 11/2 1.00 250
1 11/8 83/4 21/4 11ga x 1 1
/4 x 1 0.64 250 11/2 10 37/16 8ga x 1 3
/8 x 11/2 1.04 250
11/4 13/8 9 21/2 11ga x 1 1
/4 x 1 0.66 250 2 109/16 4 8ga x 1 3
/8 x 11/2 1.14 300
11/2 15/8 9 /8 27/8
3
11ga x 1 1
/4 x 1 0.68 500 21/2 111/8 49/16 3ga x 1 3
/8 x 11/2 1.60 400
2 21/8 915/16 33/8 8ga x 1 3
/8 x 11/2 1.06 500 3 1113/16 51/4 3ga x 1 3
/8 x 11/2 1.70 500
21/2 25/8 101/2 4 8ga x 1 3
/8 x 11/2 1.08 500 4 135/8 65/8 3ga x 1 1
/2 x 11/2 2.20 750
3 31/8 11 47/16 8ga x 1 3
/8 x 11/2 1.16 500 5 141/8 75/8 3ga x 11/2 1
/2 x 13/4 3.40 1500
4 41/8 125/8 59/16 8ga x 11/4 3
/8 x 11/2 1.66 500 6 153/8 87/8 3ga x 11/2 1
/2 x 13/4 3.72 1600
5 51/8 141/8 71/8 3ga x 11/2 1
/2 x 13/4 3.42 815 8 185/8 12 3/8 x 11/2 5
/8 x 21/2 7.22 2500
6 61/8 15 8 3ga x 11/2 1
/2 x 13/4 3.76 815 10 21 141/2 3/8 x 2 5
/8 x 21/2 10.94 2500

24
FIG. 430 Offset Pipe Clamp
SERVICE: To support horizontal piping from floors and walls. To provide lateral
bracing to vertical piping. May be used as a riser support for pipe size
up to 3”.
MATERIAL: Carbon Steel meeting ASTM: A36 and A307 Gr A
Stainless Steel Type 304 and 316 meeting ASTM: A240, F593 and F594
FINISH: Black, Electro-Galvanized meeting ASTM B633 or Hot-Dip
Galvanized meeting ASTM A123
350ºF for Electro-Galvanized and Hot-Dip Galvanized Carbon Steel.
ORDERING: Specify figure number, pipe size, material and finish. (Order
installation hardware separately.)
PIPE WEIGHT
TxW BOLT BOP A B C D LOAD 1 LOAD 2 LOAD 3
SIZE EACH, LBS.
⁄4
3 1
⁄4 x 1 ⁄4
1 3
⁄8 2 2 ⁄2
1
8 ⁄16
11
7 ⁄16
3 7
⁄16 1.61 200 100 50
1 1
⁄4 x 11⁄4 3
⁄8 2 25⁄8 91⁄16 79⁄16 7
⁄16 1.73 200 100 50
11⁄4 1
⁄4 x 11⁄4 3
⁄8 2 213⁄16 93⁄8 77⁄8 7
⁄16 1.79 200 100 75
11⁄2 1
⁄4 x 11⁄4 3
⁄8 2 215⁄16 93⁄4 81⁄4 7
⁄16 1.82 200 100 75
2 1
⁄4 x 11⁄4 3
⁄8 2 33⁄16 105⁄8 91⁄8 7
⁄16 2.05 410 200 100
21⁄2 1
⁄4 x 11⁄4 3
⁄8 2 37⁄16 12 101⁄2 7
⁄16 2.39 410 200 150
3 1
⁄4 x 11⁄4 3
⁄8 2 33⁄4 125⁄8 111⁄8 7
⁄16 2.57 410 200 175
31⁄2 1
⁄4 x 11⁄4 3
⁄8 2 4 131⁄8 115⁄8 7
⁄16 2.71 410 200 N/A
4 1
⁄4 x 11⁄2 1
⁄2 2 41⁄4 141⁄2 121⁄2 9
⁄16 3.64 600 250 N/A
5 1
⁄4 x 11⁄2 1
⁄2 2 43⁄4 153⁄4 133⁄4 9
⁄16 4.22 600 250 N/A
6 3
⁄8 x 11⁄2 1
⁄2 2 55⁄16 181⁄2 161⁄2 9
⁄16 6.91 850 350 N/A
8 3
⁄8 x 11⁄2 1
⁄2 2 65⁄16 205⁄8 185⁄8 9
⁄16 8.19 850 350 N/A
10 3
⁄8 x 3 3
⁄4 23⁄8 73⁄4 25 23 13
⁄16 20.03 900 400 N/A
12 3
⁄8 x 3 3
⁄4 23⁄8 83⁄4 27 25 13
⁄16 23.24 900 400 N/A
NOTES: BOLT TORQUE

1. Stocked in Nominal Pipe Sizes (NPS). Ductile iron, cast iron and other pipe types available upon request. ft • lbs
Provide pipe standard and/or outside diameter. 3
⁄8 20
2. Special “A” dimension available upon request. Allowable loads above do not apply to specials. 1
⁄2 50
f1 f 2 f3 1.0 where f
3. For combined loading: + + £ i is the actual load and Fi is the allowable load; i = 1,2,3. 3
⁄4 75
F1 F2 F3

25
FIG. 435 Extended Pipe Clamp
SERVICE: For direct welding of hanger to structural steel.

L D G
SIZE S EACH, LBS.
/4
3
12 3
/8 47/16 1
/4 x 11/4 1.85
1 12 3
/8 411/16 1
/4 x 11/4 2.34
11/4 12 3
/8 5 1
/4 x 11/4 2.40
11/2 12 3
/8 51/4 1
/4 x 11/4 2.45
2 12 1
/2 6 1
/4 x 11/2 3.13
21/2 12 1
/2 71/4 1
/4 x 11/2 4.20
3 12 1
/2 77/8 1
/4 x 11/2 4.47
31/2 12 1
/2 83/8 1
/4 x 11/2 4.74
4 12 1
/2 91/4 1
/4 x 11/2 4.90
5 12 1
/2 101/2 1
/4 x 11/2 5.32
6 12 5
/8 121/2 3
/8 x 2 11.15
FIG. 440 Four Section Rodding Band
SERVICE: For avoiding the possibility of joints blowing out on high pressure cast
iron water mains. Made to the City of New York or the New York Port
Authority specifications. Four FIG. #465 Square Washer plates for the
tie rod must be ordered separately.
DI PIPE STOCK TIE ROD
I.D. D E F G H K L
SIZE SIZE SIZE
4 47/8 3
/8 x 3 71/2 43/8 1 11/2 7
/8 11/4 5
/8 3
/4
6 7 3
/8 x 3 81/2 53/8 1 11/2 7
/8 11/4 5
/8 3
/4
8 91/8 1
/2 x 4 9 63/8 1 1 7
/8 11/4 5
/8 3
/4
12 133/8 1
/2 x 5 121/4 87/8 1 1 7
/8 11/2 5
/8 1
16 171/4 1
/2 x 5 141/4 107/8 1 1 7
/8 11/2 5
/8 1
20 211/2 1
/2 x 6 163/8 13 1 11/4 7
/8 11/2 5
/8 1
24 26 1
/2 x 6 19 151/4 1 11/4 7
/8 17/8 5
/8 13/8
30 321/4 5
/8 x 6 23 183/4 1 11/4 7
/8 21/4 5
/8 13/4
36 381/2 3
/4 x 8 261/4 22 1 11/2 7
/8 21/4 5
/8 13/4

26
FIG. 450 Socket Clamp for DI Pipe

FIG. 455 Socket Clamp Washer
SERVICE: Designed to prevent the separation of DI pipe joints.

ORDERING: Specify figure number, pipe size, material and finish. (Two FIG. #455
washers are required for each clamp and must be ordered separately.
If tie rod is larger than 3/4”, FIG. #455 square plate is used.)
FIG. #450
DI PIPE ROD SIZE STOCK SIZE WEIGHT EACH, LBS.
I.D. D L
SIZE A S WASHER CLAMP
3 3.96 3
/4 /85
12 3
/8 x 2 0.79 5.95
4 4.80 3
/4 /85
123/4 1
/2 x 2 0.79 8.00
6 6.90 3
/4 5
/8 151/2 1
/2 x 2 0.79 10.00
8 9.05 3
/4 5
/8 171/2 1
/2 x 2 0.79 12.10
10 11.10 3
/4 5
/8 191/2 1
/2 x 2 0.79 13.63
12 13.20 3
/4 5
/8 22 1
/2 x 2 0.79 15.65
14 15.30 1 7
/8 281/2 3
/4 x 3 2.80 45.00
16 17.40 11/8 1 303/4 3
/4 x 4 2.80 63.00
18 19.50 11/4 11/4 345/8 3
/4 x 4 2.80 76.00
20 21.60 13/8 11/4 371/2 3
/4 x 5 2.80 100.05
24 25.80 11/2 11/2 43 3
/4 x 5 2.80 119.50
30 32.00 11/2 11/2 491/2 3
/4 x 5 2.80 140.50
36 38.30 11/2 11/2 561/2 3
/4 x 5 2.80 164.50
FIG. #455
FIG. #455
PIPE TIE ROD STOCK WEIGHT
SIZE SIZE SIZE EACH, LBS.
3 3
⁄4 Cast Iron 0.79
4 3
⁄4 Cast Iron 0.79
6 3
⁄4 Cast Iron 0.79
8 3
⁄4 Cast Iron 0.79
10 3
⁄4 Cast Iron 0.79
12 3
⁄4 Cast Iron 0.79
14 1 5
⁄8 x 4 x 4 2.80
16 11⁄8 5
⁄8 x 4 x 4 2.80
18 11⁄4 5
⁄8 x 4 x 4 2.80
20 13⁄8 5
⁄8 x 4 x 4 2.80
24 11⁄2 5
⁄8 x 4 x 4 2.80
30 11⁄2 5
⁄8 x 4 x 4 2.80
36 11⁄2 5
⁄8 x 4 x 4 2.80

27
FIG. 460 Four-Bolt Socket Clamp for DI Pipe

FIG. 465 Four-Bolt Socket Clamp Washer
SERVICE: For clamping mechanical joint piping, mechanical joint

fittings or socket joint fittings together; thus stopping
separation or distortion of pipe lines under excessive
water pressure.
STANDARDS: National Fire Protection Association Standard (NFPA) 24
for outside protection.
ORDERING: Specify figure number, pipe size, material and finish. (Two
FIG. #465 Square Washers are required for each clamp and
must be ordered separately.)
FIG. #460
DI PIPE ROD SIZE STOCK SIZE WEIGHT EACH, LBS.
D I.D. L
SIZE A S WASHER CLAMP
4 /4 3
/8 5
4.80 145/8 1
/2 x 2 1.25 10
6 /4 3
/8 5
6.90 167/8 1
/2 x 2 1.25 12
8 3
/4 5
/8 9.05 191/8 5
/8 x 21/2 1.25 21
10 1 3
/4 11.10 23 5
/8 x 21/2 2.80 26
12 1 7
/8 13.20 251/8 5
/8 x 3 2.80 35
14 11/4 7
/8 15.30 281/4 3
/4 x 3 2.80 45
16 11/4 1 17.40 321/8 3
/4 x 4 2.80 69
18 11/4 11/4 19.40 351/8 3
/4 x 4 2.80 86
20 13/8 11/4 21.60 373/4 3
/4 x 5 2.80 108
24 11/2 11/2 25.80 441/2 3
/4 x 5 2.80 134
FIG. #465
PIPE TIE ROD STOCK WEIGHT FIG. #465
SIZE SIZE SIZE EACH, LBS.
4 3
⁄4 1
⁄2 x 3 x 3 1.25
6 3
⁄4 1
⁄2 x 3 x 3 1.25
8 3
⁄4 1
⁄2 x 3 x 3 1.25
10 1 5
⁄8 x 4 x 4 2.80
12 1 5
⁄8 x 4 x 4 2.80
14 11⁄4 5
⁄8 x 4 x 4 2.80
16 11⁄4 5
⁄8 x 4 x 4 2.80
18 11⁄4 5
⁄8 x 4 x 4 2.80
20 13⁄8 5
⁄8 x 4 x 4 2.80
24 11⁄2 5
⁄8 x 4 x 4 2.80
30 11⁄2 5
⁄8 x 4 x 4 2.80
36 11⁄2 5
⁄8 x 4 x 4 2.80
FIG. 470 Corporation Eye Bolt
SERVICE: For use with FIG. #450 socket clamp.

MATERIAL: Carbon Steel or 304 Stainless Steel
ORDERING: Specify figure number and finish.
ROD SIZE T L
A
3
/4 3 41/2

28
FIG. 500 Pipe Alignment Guide
SERVICE: To provide axial pipe alignment near an expansion joint for horizontal and
vertical runs. Attached to steel beams by bolting or welding, and concrete
slabs by anchor bolting.
MATERIAL: Carbon Steel meeting ASTM: A36, A307 Gr A and A563 Gr A
FINISH: Black or Hot-Dip Galvanized meeting ASTM: A153
ORDERING: Specify figure number, size number, pipe size, insulation thickness, material
and finish. (Order installation hardware separately.)
GUIDE SIZE SELECTION TABLE GUIDE DIMENSIONS
PIPE NOMINAL INSULATION THICKNESS, J SIZE WEIGHT
A B C D E F G H
SIZE 0 1 11/2 2 21/2 3 4 5 NO. EACH, LBS.
/2-1
1
1 1 1 2 3 3 4 5 1 4 53/8 4 21/2 9
/16 71/16 91/2 8 14.3
11/4 1 1 2 3 3 4 4 5 2 4 /2
1
53/4 4 21/2 9
/16 81/8 111/4 8 17.9
11/2-2 1 1 2 3 3 4 5 6 3 6 7 6 4 9
/16 109/16 123/4 10 29.6
21/2 2 2 3 3 4 4 5 6 4 71/2 85/16 6 4 11
/16 133/16 151/2 10 38.8
3 2 2 3 3 4 4 5 7 5 81/2 83/4 8 5 11
/16 151/4 171/2 12 52.5
31/2-4 3 3 3 4 4 5 6 7 6 91/4 1111/16 8 5 13
/16 167/8 191/4 12 65.7
5 4 4 4 4 5 5 7 8 7 101/8 12 8 5 13
/16 183/4 201/2 12 67.3
6 4 4 4 5 5 6 7 8 8 11 131/4 8 5 13
/16 201/4 221/2 12 78.4
8 6 6 6 6 7 7 8 9 9 12 139/16 8 5 15
/16 221/4 241/2 12 93.8
10 8 8 8 8 8 8 9 10 10 133/4 151/4 8 5 15
/16 26 281/2 12 129.2
12 9 9 9 9 9 9 10 10 11 143/4 153/4 8 5 15
/16 28 30 12 136.7
14 10 10 10 10 10 10 10 11 12 161/4 183/4 8 5 11/8 311/2 34 12 152.5
16 10 10 10 10 10 10 11 12 13 181/4 191/2 8 5 11/8 351/2 391/2 12 173.2
18 11 11 11 11 11 11 12 12
20 12 12 12 12 12 12 12 13
24 13 13 13 13 13 13 13 13
NOTES:
ALLOWABLE TRAVEL
2. Not to be used as a gravity support. SIZE NO. U S
3. Guide spacing in accordance with Expansion Joint Manufacturers Association (EJMA) Standards.
4. If larger travel required, contact factory. 1-2 +8 ±4
5. Shell ears may be rotated for closely spaced adjacent pipe runs, G’ ≈ G - 4 in. 3-4 +10 ±5
5-13 +12 ±6

29
FIG. 502 Light Duty Pipe Alignment Guide
SERVICE: To provide axial pipe alignment near an expansion joint for horizontal and
vertical runs. Attached to steel beams by bolting or welding, and concrete
slabs by anchor bolting.
FINISH: Black or Hot-Dip Galvanized meeting ASTM: A153
ORDERING: Specify figure number, size number, pipe size, insulation thickness, material
and finish. (Order installation hardware separately.)
GUIDE SIZE SELECTION TABLE GUIDE DIMENSIONS
PIPE NOMINAL INSULATION THICKNESS, J SIZE WEIGHT
A B C D E F G H
SIZE 0 1 11/2 2 21/2 3 4 5 NO. EACH, LBS.
/2-1
1
1 1 1 2 3 3 4 5 1 4 53/8 3 11/2 9
/16 71/16 91/2 4 9.7
11/4 1 1 2 3 3 4 4 5 2 4 /2
1
53/4 3 11/2 9
/16 81/8 111/4 4 12.1
11/2-2 1 1 2 3 3 4 5 6 3 6 7 3 11/2 9
/16 109/16 123/4 4 15.0
21/2 2 2 3 3 4 4 5 6 4 71/2 85/16 3 11/2 9
/16 133/16 151/2 4 19.7
3 2 2 3 3 4 4 5 7 5 81/2 83/4 4 2 11
/16 151/4 171/2 4 25.6
31/2-4 3 3 3 4 4 5 6 7 6 91/4 1111/16 4 2 13
/16 167/8 191/4 4 35.6
5 4 4 4 4 5 5 7 8 7 101/8 12 4 2 13
/16 183/4 201/2 4 36.3
6 4 4 4 5 5 6 7 8 8 11 131/4 6 4 13
/16 201/4 221/2 6 52.1
8 6 6 6 6 7 7 8 9 9 12 139/16 6 4 15
/16 221/4 241/2 6 62.1
10 8 8 8 8 8 8 9 10 10 133/4 151/4 6 4 15
/16 26 281/2 6 81.1
12 9 9 9 9 9 9 10 10
14 10 10 10 10 10 10 10 -
16 10 10 10 10 10 10 - -
NOTES:
ALLOWABLE TRAVEL
2. Not to be used as a gravity support. SIZE NO. U S
3. Guide spacing in accordance with Expansion Joint Manufacturers Association (EJMA) Standards.
4. If larger travel required, see FIG. #500. 1-7 +4 ±2
5. Shell ears may be rotated for closely spaced adjacent pipe runs, G’ ≈ G - 4 in. 8-10 +6 ±3

30
FIG. 515 Adjustable Pipe Support
SERVICE: For use in conjunction with a standard pipe and flange at base to support
piping where an overhead supporting member is not available. The stem is
threaded the full length with a nut to allow a vertical adjustment to
accommodate the pitch in the pipe line.
PIPE STOCK DIA. & LENGTH WEIGHT
SIZE SIZE OF STEM EACH, LBS.
2 /8 x 11/2
3
/8 x 8
7
1.92
3 /8 x 11/2
3
/8 x 8
7
2.20
4 3
/8 x 2 1x8 3.23
5 3
/8 x 2 1x8 3.67
6 1
/2 x 2 11/4 x 8 5.92
8 1
/2 x 2 11/4 x 8 6.77
10 1
/2 x 3 11/2 x 8 11.56
12 1
/2 x 3 11/2 x 8 13.08
FIG. 516 Adjustable Pipe Support w/ U-Bolt

FIG. 517 Adjustable Pipe Support w/ DI U-Bolt
SERVICE: For use in conjunction with a standard pipe and flange at the base to support
piping where an overhead supporting member is not available. The stem is
threaded the full length with a nut to allow vertical adjustment to
accommodate the pitch in the pipe line.
PIPE STOCK DIA. & LENGTH WEIGHT
3 3
/8 x 11/2 7
/8 x 8 3.2
31/2 /8 x 11/2
3 7
/8 x 8 3.3
4 3
/8 x 2 1x8 4.3
5 3
/8 x 2 1x8 4.7
6 1
/2 x 2 11/4 x 8 8.2
8 1
/2 x 2 11/4 x 8 9.3
10 1
/2 x 3 11/2 x 8 16.0
12 1
/2 x 3 11/2 x 8 19.9
DI PIPE STOCK DIA. & LENGTH WEIGHT
3 3
/8 x 11/2 7
/8 x 8 3.3
4 3
/8 x 2 1x8 4.5
6 1
/2 x 2 11/4 x 8 8.5
8 1
/2 x 2 11/4 x 8 9.6
10 1
/2 x 3 11/2 x 8 15.6
12 1
/2 x 3 11/2 x 8 19.3

31
FIG. 519 Pipe Saddle Support w/ DI U-Bolt

FIG. 520 Pipe Saddle Support w/ U-Bolt
FIG. 521 Pipe Saddle Support
SERVICE: For general piping running close to the floor.

STANDARDS: MSS SP-58 Type 37 (FIG. #520) Type 36 (FIG. #521)
ORDERING: Specify figure number, pipe size, L dimension, material and
finish. (Saddle furnished complete with or without U-Bolt.
Gussets will be added to supports for pipe sizes 8” and
above. Welded base plate and pipe as shown must be
ordered separately.)
DI PIPE WEIGHT
A B C
SIZE EACH, LBS.
4 3 45/16 10 6.88
6 3 59/16 10 11.32
8 3 71/8 10 14.57
10 3 85/8 10 18.11
12 3 103/16 10 23.34
14 4 119/16 10 38.92
16 4 131/16 10 44.32
18 4 145/8 10 52.67
20 6 163/16 12 84.55
24 6 1813/16 12 99.93
PIPE WEIGHT
A B C
SIZE EACH, LBS.
4 3 43/16 10 6.72
5 3 413/16 10 7.30
6 3 57/16 10 11.06
8 3 615/16 10 14.30
10 3 87/16 10 18.53
12 3 915/16 10 23.92
14 4 1015/16 10 39.10
16 4 123/8 10 44.47 SHOWN WITH OPTIONAL STAND
18 4 137/8 10 52.95
20 6 153/8 12 84.72
24 6 1715/16 12 100.00
30 6 215/16 12 113.10
36 8 241/2 12 163.74
NOTE: Weights are for saddles only.

32
FIG. 525 Pipe Saddle Support

D L
SIZE S EACH, LBS.
2 /8 x 11/2
3
/8
7
6 1.57
3 /8 x 11/2
3
/8
7
6 1.85
4 3
/8 x 2 1 6 2.70
5 3
/8 x 2 1 6 3.14
6 1
/2 x 2 11/4 6 4.90
8 1
/2 x 2 11/4 6 5.75
10 1
/2 x 3 11/2 6 9.88
12 1
/2 x 3 11/2 6 11.40
FIG. 530 Adjustable Pipe Saddle Support w/ Coupling

PIPE STOCK SIZE COUPLING WEIGHT
SIZE S SIZE EACH, LBS.
2 /8 x 2
3
11/4 1.35
3 /8 x 21/2
3
11/2 2.45
4 3
/8 x 3 2 3.63
5 3
/8 x 3 2 4.30
6 1
/2 x 4 21/2 7.03
8 1
/2 x 4 21/2 8.53
10 1
/2 x 4 3 13.04
12 1
/2 x 4 3 15.07

33
FIG. 535 Adjustable Pipe Saddle Support

FIG. 538 Adjustable Pipe Saddle Support w/ U-Bolt
FIG. 539 Adjustable Pipe Saddle Support w/ DI U-Bolt

STANDARDS: MSS SP-58 Type 37 (FIG. #538 and FIG. #539), Type 38 (FIG. #535)
ORDERING: Specify figure number, pipe size, L dimension, material and finish.
(Unit consists of saddle, nipple and reducer. Gussets will be added
to supports for pipe sizes 8” and above. Welded base plate and pipe
must be ordered separately.)
DIMENSION E WEIGHT EACH, LBS.
PIPE PIPE
SIZE SIZE B C D SADDLE WITH
A MIN. MAX. ONLY REDUCER
21/2 21/2 37/16 8 11/2 8 13 4.14 7.44
3 21/2 311/16 8 11/2 81/4 131/4 4.40 7.70
4 3 43/16 10 21/2 91/4 14 5.83 13.39
5 3 413/16 10 21/2 10 143/4 6.48 14.04
6 3 57/16 10 21/2 101/2 151/4 10.24 17.80
8 3 615/16 10 21/2 113/4 161/2 13.16 20.72
10 3 87/16 10 21/2 131/2 181/4 17.23 24.79
12 3 915/16 10 21/2 15 193/4 22.56 30.12
14 4 1015/16 10 3 161/4 203/4 29.20 42.55
16 4 123/8 10 3 173/4 221/4 33.53 46.88
18 6 137/8 12 4 191/2 24 52.83 74.78
20 6 153/8 12 4 21 251/2 56.96 78.91
24 6 1715/16 12 4 233/4 281/4 78.92 100.87
30 6 215/16 12 4 27 311/2 90.40 112.35
36 6 241/2 12 4 301/4 343/4 107.92 129.87
DI PIPE DIMENSION E WEIGHT EACH, LBS.
PIPE SIZE B C D SADDLE WITH
SIZE A MIN. MAX. ONLY REDUCER
3 2 /21
3 /16
15
8 1 /2
1
8 /2
1
131/2 4.52 7.82
4 3 45/16 10 21/2 93/8 143/8 5.99 13.55
6 3 59/16 10 21/2 105/8 155/8 10.50 18.06
SHOWN WITH OPTIONAL STAND
8 3 71/8 10 21/2 1115/16 1611/16 13.43 20.99
10 3 85/8 10 21/2 1311/16 187/16 16.81 24.37
12 3 103/16 10 21/2 151/4 20 21.98 29.54
14 4 119/16 10 3 167/8 213/8 29.02 42.37
16 4 131/16 10 3 187/16 2215/16 33.38 46.73
18 6 145/8 12 4 201/4 243/4 52.55 74.50
20 6 163/16 12 4 2113/16 265/16 56.79 78.74
24 6 1813/16 12 4 245/8 291/8 78.85 100.80
30 6 225/16 12 4 28 321/2 94.57 116.52
36 6 255/8 12 4 313/8 357/8 109.32 131.27

34
FIG. 540 Angle Iron Support
SERVICE: For general piping. Must be installed long leg vertical.

ORDERING: Specify figure number, rod size, angle size, center to
center of holes, material and finish.
ALLOWABLE CONCENTRATED LOAD AT CENTER OF SPAN, LBS
ANGLE SIZE
10 12 18 24 30 36 48 60 72 84
11/2 x 11/2 x 1/4 1109 924 616 462 - - - - - -
2 x 2 x 1/4 2117 1764 1177 882 710 590 - - - -
3 x 3 x 1/4 - 3860 2577 1930 1540 1290 970 - - -
4 x 3 x 3/8 - - - - - 3330 2500 2000 1670 1430
5 x 3 x 3/8 - - - - - 4900 3660 2930 2440 2100
6 x 4 x 3/8 - - - - - 7350 5500 4400 3670 3140
FIG. 550 Angle Bracket
SERVICE: For use on the side of steel or wood beams.

ORDERING: Specify figure number, bolt size, material and finish.
BOLT HOLE SIZE WEIGHT MAX. REC.
B C D E
SIZE A EACH, LBS. LOAD, LBS.
3
/8 7
/16 21/16 8ga 15/16 11/2 0.23 300
1
/2 9
/16 21/8 3ga 13/8 11/2 0.33 560
5
/8 11
/16 3 1
/4 13/4 3 1.15 900
3
/4 13
/16 3 3
/8 13/4 3 1.69 1300
7
/8 15
/16 4 3
/8 21/2 4 3.12 1800 A
B
1 11/8 4 1
/2 21/2 4 4.02 2400 A D
D
B C E

35
FIG. 545 Channel Assembly
SERVICE: To support single and multiple piping services on a common member

such as a trapeze suspended by two threaded rods or as supplemental
steel attached to the structure. Back-to-back channel assembled with
spacers for rod clearance and adjustment. Available with or without
washer plates. Washer plates may be welded or loose.
MATERIAL: Carbon Steel meeting ASTM: A36
MAX TEMP: 650ºF for Black Carbon Steel
STANDARDS: MSS SP-58 Type 59, Trapeze
ORDERING: Specify figure number, channel size, overall length (OAL), span, rod
size, with washer plates welded (W) or loose (L) or without (N) and
finish. (Example: Fig 545-6-76.75-72-1-W-HDG)
MAXIMUM RECOMMENDED LOAD ROD & WASHER SELECTION
C3 x 4.1 C4 x 5.4 C5 x 6.7 C6 x 8.2 C8 x 11.5 C10 x 15.3 C12 x 20.7 C15 x 33.9 WASHER
SPAN ROD LOAD
8.2 lb/ft 10.8 lb/ft 13.4 lb/ft 16.4 lb/ft 23 lb/ft 30.6 lb/ft 41.4 lb/ft 67.8 lb/ft WxWxT
36 2900 5100 7900 11600 21700 - - - 3
⁄8 730 3 x 3 x 1⁄4
48 2200 3800 5900 8700 16200 - - - 1
⁄2 1350 3 x 3 x 1⁄4
60 1700 3000 4700 6900 13000 21600 - - 5
⁄8 2160 3 x 3 x 3⁄8
72 1400 2500 3900 5800 10800 18000 - - 3
⁄4 3230 4 x 4 x 3⁄8
84 1200 2100 3400 4900 9300 15400 24500 - 7
⁄8 4480 4 x 4 x 1⁄2
96 1100 1900 2900 4300 8100 13500 21500 - 1 5900 4 x 4 x 1⁄2
108 900 1700 2600 3800 7200 12000 19100 - 11⁄8 7420 4 x 4 x 1⁄2
120 800 1500 2300 3400 6500 10800 17200 - 11⁄4 9500 4 x 4 x 1⁄2
132 800 1300 2100 3100 5900 9800 15600 - 13⁄8 11290 5 x 5 x 3⁄4
144 - 1200 1900 2900 5400 9000 14300 - 11⁄2 13800 5 x 5 x 3⁄4
156 - 1100 1800 2600 5000 8300 13200 - 13⁄4 18600 5 x 5 x 3⁄4
168 - 1000 1700 2400 4600 7700 12200 24000 2 24600 5 x 5 x 3⁄4
180 - - 1500 2300 4300 7200 11400 22400 See Note 2
192 - - 1400 2100 4000 6700 10700 21000
204 - - 1400 2000 3800 6300 10100 19700
216 - - - 1900 3600 6000 9500 18600
228 - - - 1800 3400 5600 9000 17600
240 - - - 1700 3200 5400 8600 16800
NOTES:
1. Load based on simply supported beam with a concentrated load at mid-span. All deflections at mid-span less than Span/360.
2. Each rod size may be based on one half the maximum recommended load for symmetrically loaded channel assemblies. For varying
load distributions, each rod size is recommended to be based on the full load unless calculations have been performed.
3. Welding in accordance with AWS D1.1.
4. Interior spacers partially welded for field removal if necessary.
5. For special designs contact factory with dimensions, material, loading, finish, and additional design criteria.

36
FIG. 558 Metal Deck Anchor Bolt
SERVICE: To provide a pre-positioned hanger rod attachment to the underside

of concrete slabs on metal form decks. Used as a cast-in-place
concrete anchor bolt on deck upper flute in 3,000 psi minimum
compressive strength normal and lightweight, cracked and uncracked
concrete loaded by static tensile forces from piping or similar services.
MATERIAL: Carbon Steel meeting ASTM A36 and A307 Gr A
FINISH: Black or Electro-Galvanized meeting ASTM B633
MAX TEMP: 200ºF
ORDERING: Specify figure number, anchor size and finish. (Order hardware
separately.)
ANCHOR WIDTH DECK WEIGHT MAX. REC.
SIZE W HOLE EACH, LBS. LOAD, LBS.
3
/8 11/2 1
/2 1.21 730
1
/2 11/2 5
/8 1.33 800
5
/8 11/2 3
/4 1.54 800
3
/4 2 7
/8 2.16 800
7
/8
Contact Factory (Note 2)
1
NOTES:
1. Safety factor of 4.0 against nominal strength calculated in accordance with American Concrete Institiute (ACI) 318,
Appendix D, 2011. Maximum recommended tensile loads presented above are unfactored. Minimum concrete com-
pressive strength = 3,000 psi. Concrete assumed cracked. Concrete breakout governs the maximum recommended
tensile load. Condition B applies. Edge and spacing effects not included in maximum recommended tensile load
development. Follow minimums specified above.
2. Provide concrete compressive strength and slab thickness.
3. Do not load anchor bolt until concrete has fully cured.
4. Use a minimum of one deck screw to secure anchor bolt during concrete pour. Screw may be #12 or smaller.
5. Mounting bar is not a structural element.
6. Minimum cover based on conditions not exposed to weather in accordance with ACI 318, Section 7.7.1(c).

37
FIG. 561 Female Overhead Anchor Bolt
SERVICE: To provide a pre-positioned hanger rod attachment to the underside of

concrete slabs on wood forms. Used as a cast-in-place concrete anchor
bolt in 3,000 psi minimum compressive strength normal and lightweight,
cracked and uncracked concrete loaded by static tensile forces from
piping or similar services.
MAX TEMP: 200ºF
ORDERING: Specify figure number, anchor size, and finish. (Order hardware separately.)
ANCHOR EMBED DEPTH MIN SLAB MIN EDGE MIN SPACING WEIGHT MAX. REC.
SIZE “H” “T” “C” “S” EACH, LBS. LOAD, LBS.
3
/8 3 41/2 6 12 1.20 730 †
1
/2 3 41/2 6 12 1.40 1350 †
5
/8 31/2 5 7 14 1.45 2160 ‡
3
/4 31/2 5 7 14 1.68 2160 ‡
7
/8 4 51/2 8 16 2.17 2600 ‡
1 4 6 8 16 2.26 2600 ‡
11/4 5 7 10 20 3.69 3600 ‡
11/2 6 81/2 12 24 5.62 4800 ‡
NOTES:
1. Safety factor of 4.0 against nominal strength calculated in accordance with American Concrete Institute (ACI) 318, Appendix D, 2011.
Maximum recommended tensile loads presented above are unfactored. Minimum concrete compressive strength = 3,000 psi. Concrete
assumed cracked. † pullout governs, ‡ breakout governs the maximum recommended tensile load. Condition B applies. Edge and
spacing effects not included in maximum recommended tensile load development. Follow minimums specified above.
2. Do not load anchor bolt until concrete has fully cured.
3. Use a minimum two nails or screws to secure anchor bolt during concrete pour. Remove nails or screws after forms are removed.
4. Mounting plate is not a structural element.
5. Minimum cover based on conditions not exposed to weather in accordance with ACI 318, Section 7.7.1.(c).

38
FIG. 600 Concrete Insert Box

FIG. 605 Concrete Insert Nut
SERVICE: Heavy gauge insert box is nailed to concrete form and can
accommodate 1/4” to 3/4” rod diameters. When concrete has
set, knock out plug can be removed and insert nut installed.
Side openings accommodate up to 1/2” reinforcing rods.
ORDERING: Specify figure number. (FIG. #605 Insert Nut must FIG. #605 FIG. #600
be ordered separately by rod size.)
FIG. #600 FIG. #605
ROD SIZE WEIGHT
A B C D E WEIGHT EACH, LBS. MAX. REC. LOAD, LBS. B C
A EACH, LBS.
37/8 13⁄4 25⁄8 13
⁄16 21⁄8 0.96 1200 3
⁄8 5
⁄16 11⁄4 0.13
1
⁄2 5
⁄16 11⁄4 0.12
E
5
⁄8 5
⁄16 11⁄4 0.11
3
⁄4 5
⁄16 11⁄4 0.10
D
FIG. 610 C-Clamp

FIG. 615 C-Clamp w/ Locknut
FIG. 620 C-Clamp Retaining Strap
SERVICE: For attaching to I-beams and wide flange beams where

thickness does not exceed ¾”. Flange thickness may not
exceed 5/8” when clamp is used with a retaining strap.
APPROVALS: FM (FIG. #615 and FIG. #610 with FIG. #620)
ORDERING: Specify figure number, rod size, material and finish. FIG. #610 FIG. #615
ROD SIZE MAX PIPE WEIGHT PER MAX. REC. FIG. #620 WEIGHT PER
FIG. # C-CLAMP C D F
B SIZE EACH, LBS. LOAD, LBS. L EACH, LBS.
610 Standard 3
/8 23/8 23/8 3
/4 4 0.38 400 41/2 0.21
610 Standard 1
/2 23/8 25/16 3
/4 4 0.38 500 6 0.30 FIG. #620
610 Standard 5
/8 23/8 25/16 3
/4 5 0.56 550 8 0.36
610 Standard 3
/4 25/16 21/4 3
/4 6 0.60 630 10 0.45
615 With Lock Nut 3
/8 23/8 23/8 3
/4 4 0.40 400 12 0.54
615 With Lock Nut 1
/2 23/8 25/16 3
/4 4 0.40 500 14 0.62
615 With Lock Nut 5
/8 23/8 25/16 3
/4 5 0.60 550
615 With Lock Nut 3
/4 25/16 21/4 3
/4 6 0.68 630

39
FIG. 618 Purlin Clamp
SERVICE: For use with large-lip steel purlin beams.

MATERIAL: Ductile Iron
ORDERING: Specify figure number and finish.
ROD SIZE SET WEIGHT MAX. REC.
B C D E
A SCREW EACH, LBS. LOAD, LBS.
3
/8 1 1 17/8 15/8 3
/8 - 16 x 3 0.92 400
FIG. 630 Electrical Beam Clamp
SERVICE: For attaching hanger rod to beam or framework where thickness does not
exceed 1/2”. Rod tapped on both bottom and back of clamp.
MATERIAL: Malleable Iron
ORDERING: Specify figure number and rod size.
ROD SIZE SET WEIGHT MAX. REC.
B C D
A SCREW EACH, LBS. LOAD, LBS.
1
/4 13/16 13/8 13/8 5
/16 - 18 0.26 335
3
/8 21/16 17/8 13/4 1
/2 - 13 0.70 525
1
/2 21/2 23/8 23/16 1
/2 - 13 1.26 750

40
FIG. 635 Junior Top Beam Clamp
SERVICE: For use under roof installations with bar joist type construction where the
thickness of the joist does not exceed 5/8”.
MATERIAL: Malleable Iron casting or 304 Stainless Steel
APPROVALS: FM (3/8” & 1/2” rod), UL
ORDERING: Specify figure number, rod size and finish. (Furnished with a hardened cup
point set screw and lock nut.)
ROD SIZE MAX PIPE WEIGHT MAX. REC.
B C D E F
A SIZE EACH, LBS. LOAD, LBS.
3
/8 15/16 11/2 1
/2 1 7
/8 4 0.32 350
1
/2 15/16 11/2 1
/2 1 7
/8 4 0.32 470
5
/8 13/4 13/4 5
/8 13/8 11/8 5 0.58 550
3
/4 17/8 17/8 5
/8 13/8 13/8 6 0.82 700
7
/8 23/8 17/8 5
/8 13/8 13/8 8 0.80 1000
NOTE: FIG. #635 3/8” Electro-Galvanized is substituted with a FIG. #638 Domestic
Jr. Top Beam Clamp 3/8” Electro-Galvanized.
FIG. 636 Junior Top Beam Clamp, Domestic
SERVICE: For attaching hanger rod to top or bottom of flange of a beam or bar joist where
thickness does not exceed 3/4”.
MATERIAL: Malleable Iron casting
STANDARDS: MSS SP-58 Type 19 & 23
APPROVALS: FM (NFPA 13, max related size), UL (Top & Bottom of beam)
ORDERING: Specify figure number, rod size and finish. (Furnished with a hardened cup
point set screw and lock nut.)
ROD SIZE WEIGHT MAX. REC.
B C D E F
A EACH, LBS. LOAD, LBS.
1
/2 1 11/2 1
/2 1 7
/8 0.39 500
5
/8 11/2 11/2 1
/2 1 1 0.58 600
3
/4 17/8 13/4 5
/8 13/8 11/4 0.82 800
7
/8 2 13/4 5
/8 11/2 11/4 0.79 1200

41
FIG. 637 Top Beam Clamp Retaining Strap
SERVICE: For use with FIG. #635, FIG. #636, FIG. #638 and FIG. #640 to eliminate
movement of beam clamp due to vibration.
ORDERING: Specify figure number, rod size, length, material and finish. (Sizes shown
are carried in stock, other sizes are also available. For proper length, add
2” to flange width and select the next size strap.)
ROD SIZE STOCK LENGTH HOLE WEIGHT C
A SIZE C SIZE EACH, LBS.
3
/8 14ga x 1 10 7
/16 0.21
1
/2 14ga x 1 10 9
/16 0.21
5
/8 14ga x 11/4 10 11
/16 0.24 A
3
/4 14ga x 11/4 10 13
/16 0.24
7
/8 14ga x 2 10 15
/16 0.43
FIG. 638 Junior Top Beam Clamp, Domestic
SERVICE: For attaching hanger rod to top or bottom flange of a beam or a bar joist,
where thickness does not exceed 3/4”. The open back design permits rod
adjustment and visual verification during installation.
MATERIAL: Carbon Steel or 304 Stainless Steel
STANDARDS: MSS SP-58 Type 19 & 23, FS WW-H-171E
APPROVALS: FM (NFPA 13, max related size), UL (Top & bottom of beam),
ORDERING: Specify figure number, rod size, and finish.
(Furnished with a hardened cup point set screw
and lock nut.)
ROD SIZE WEIGHT MAX. REC.
B C D E F G
“A” EACH, LBS. LOAD, LBS
F
/8
3
113/16 15/8 /32
17 3
/4 /8 min.
3 15
/16 0.20 400
FIG. 640 Wide Top Beam Clamp
SERVICE: For use under roof installations with bar joist type construction where
the thickness of the joist does not exceed 1¼”.
MATERIAL: Malleable Iron casting
APPROVALS: FM (3/8” Only), UL (3/8” and 1/2” [1/2” for 4” IPS Max])
B F
ORDERING: Specify figure number, rod size, and finish. D
(Furnished with a hardened cup point set screw
and lock nut.) C
ROD SIZE MAX. PIPE WEIGHT MAX. REC.
B C D E F
“A” SIZE EACH, LBS. LOAD, LBS.
3
/8 1 /8
3
2 1
/2 1 7
/8 4 0.55 400 A
1
/2 13/8 2 1
/2 1 7
/8 4 0.56 500
5
/8 17/8 23/8 5
/8 13/8 11/4 5 0.66 850 E
3
/4 17/8 23/8 5
/8 13/8 11/4 6 0.83 900

42
FIG. 645 Welding Beam Attachment

FIG. 650 Welding Beam Attachment w/ Bolt and Nut
SERVICE: To provide hanger rod attachment to structural member bottom flange. Used to
provide vertical hanger rod adjustment or to permit horizontal pipe movement
through hanger rod rotation for pipe support assemblies loaded by static and
dynamic tensile forces from piping or similar services.
350ºF for Hot-Dip Galvanized Carbon Steel FIG. #645
ORDERING: Specify figure number, rod size, material and finish. (Order hardware
separately.)
ROD SIZE BOLT WEIGHT EACH, LBS. MAX. REC.
TxW E G F R S H X
A B FIG. #645 FIG. #650 LOAD, LBS.
3
/8 3ga x 2 1
/2 x 23/4 2 41/2 2 7
/8 11/2 /16
9 1
/4 0.83 1.04 730
1
/2 3ga x 2 5
/8 x 23/4 2 41/2 2 7
/8 11/2 11
/16 1
/4 0.81 1.16 1350
5
/8 3ga x 2 3
/4 x 3 2 43/8 2 7
/8 11/2 13
/16 1
/4 0.78 1.34 2160 FIG. #650
3
/4 3
/8 x 21/2 7
/8 x 31/2 2 41/4 2 11/8 19/16 15
/16 5
/16 1.61 2.52 3230
7
/8 3
/8 x 21/2 1x4 3 61/8 3 11/4 21/16 11/16 5
/16 2.30 3.68 4480
1 1
/2 x 3 11/8 x 51/2 3 61/8 3 11/2 23/4 11/4 5
/16 4.07 6.45 5900
11/8 1
/2 x 3 11/4 x 51/2 3 71/16 3 13/4 23/4 13/8 3
/8 4.10 7.22 7420
11/4 5
/8 x 4 13/8 x 6 † 3 7 3 2 3 11/2 3
/8 7.28 9.82 9500
11/2 3
/4 x 5 15/8 x 61/2 † 4 77/8 4 21/2 31/2 13/4 3
/8 14.49 18.31 13800
13/4 3
/4 x 5 17/8 x 67/8 † 5 125/8 5 23/4 33/4 2 3
/8 16.53 21.86 18600
2‡ 3
/4 x 6 21/4 x 67/8 † 5 127/16 51/4 31/4 33/4 23/8 3
/8 24.94 32.84 24600
Notes:
† FIG. #650 bolt and nut replaced by pin with cotters.
‡ FIG. #645 and FIG. #650 welded construction. Weld all-around to structural member.
1. Maximum hanger rod in-plane and out-of-plane rotation resultant ≤ 4º per MSS SP-58. Pipe attachment shall provide rotation.
2. Welding in accordance with AWS D1.1 for carbon steel with 70000 psi filler metal and AWS D1.6 for stainless steel with 80000 psi filler
metal.
3. Welding may be all-around to structure as necessary.

43
FIG. 646 Concrete Rod Attachment Plate

FIG. 647 Concrete Clevis Plate
SERVICE: To provide hanger rod attachment to the underside of concrete slabs.

Allows vertical hanger rod adjustment or permits horizontal pipe movement
through hanger rod rotation. Attached by post-installed or cast-in-place
anchor bolts in 3,000 psi minimum compressive strength normal weight
and lightweight, cracked and uncracked concrete loaded by static tensile
forces from piping or similar services. FIG. #646
350ºF for Hot-Dip Galvanized Carbon Steel FIG. #647
ORDERING: Specify figure number, rod size, material and finish. (Order anchor bolts
and hardware separately.)
BOLT WEIGHT EACH, LBS. MAX. REC.
SIZE TxW A C E F G H J K P Q R S V Y
B FIG. #646 FIG. #647 LOAD, LBS.
/8 3ga x 2 1/2 x 23/4
3
1 10 2 2 47/8 9/16 3
/8 9
/16 1
/2 2 4 11/2 3 6 11.6 11.9 730
/2 3ga x 2 5/8 x 23/4
1
1 10 2 2 47/8 11/16 3
/8 9
/16 1
/2 2 4 11/2 3 6 11.6 12.0 1350
5
/8 3ga x 2 3/4 x 3 1 10 2 2 47/8 13/16 1
/2 9
/16 1
/2 2 4 11/2 3 6 15.2 15.8 2160
3
/4 3/8 x 21/2 7/8 x 31/2 1 10 2 2 43/4 15/16 1
/2 11
/16 5
/8 23/4 6 19/16 5 10 16.1 17.0 3230
7
/8 3/8 x 21/2 1x4 1 10 3 3 65/8 11/16 1
/2 11
/16 5
/8 23/4 6 21/16 5 10 16.7 18.1 4100
1 1
/2 x 3 11/8 x 51/2 2 12 3 3 67/8 11/4 3
/4 13
/16 3
/4 31/8 6 23/4 6 12 35.0 36.9 5400
11/8 1/2 x 3 11/4 x 51/2 2 12 3 3 713/16 13/8 3
/4 15
/16 7
/8 31/2 10 23/4 6 12 35.2 37.9 5800
11/4 5/8 x 4 13/8 x 6 † 2 12 3 3 73/4 11/2 3
/4 15
/16 7
/8 31/2 10 3 6 12 40.9 43.0 5800
11/2 3/4 x 5 15/8 x 61/2 † 2 12 4 4 87/8 13/4 1 11/8 1 43/8 10 31/2 7 14 57.6 60.0 5800
Notes:
† Figure 647 bolt and nut replaced by pin with cotters.
1. Concrete attachment based on Powers Fasteners Power-Stud+ SD1 post-installed wedge expansion anchor bolt in 3,000 psi
minimum compressive strength cracked concrete. Concrete failure modes in accordance with American Concrete Institute (ACI) 318,
Appendix D, 2011. Minimum safety factor of 3.5 and 4.0 for steel and concrete failure modes, respectively. Maximum recommended
loads presented above are unfactored. Condition B applies.
2. Maximum hanger rod in-plane and out-of-plane rotation resultant ≤ 4º per MSS SP-58. Pipe attachment shall provide rotation.
3. Other anchor bolt types and embedment depth combinations may be used. Contact factory for assistance.

44
FIG. 655 Side Beam Connector
SERVICE: For mounting to the side of wood beams. Bottom hole is

tapped for rod.
MATERIAL: Malleable Iron
ORDERING: Specify figure number, rod size, and finish.
SIZE ROD SIZE WEIGHT MAX. REC.
B C
NO. A EACH, LBS. LOAD, LBS.
1 /8
3
21/8 /8
5
0.13 250
2 /2
1
23/4 /4
3
0.29 480
FIG. 665 Adjustable Rod Beam Clamp
SERVICE: To be used in the suspension of a hanger rod from an I-beam.

Recommended for the attachment of beams where the flange widths
are from 4” to 8”.
ROD STOCK ADJUSTMENT WEIGHT MAX. REC.
G H B
SIZE SIZE MIN. MAX. EACH, LBS. LOAD, LBS.
3
/8 11/16 /16
7
2 3ga x 11/4 31/2 8 0.98 300
1
/2 1 /16
9
2 3ga x 11/2 31/2 8 1.38 700
5
/8 15
/16 11
/16 2 3ga x 13/4 31/2 8 1.86 1000

45
FIG. 675 Adjustable Center Beam Clamp
SERVICE: To hang piping with a threaded rod from the bottom center of wide
flange beams (W-Shape) or American standard beams (S-Shape).
Provides vertical hanger rod adjustment. For hanger assemblies loaded
by static tensile forces from piping or similar services.
MATERIAL: Carbon Steel meeting ASTM: A36, A307 Gr A, and A563 Gr A
Stainless Steel Type 304 and 316 meeting ASTM: A240, F593, and F594
350ºF for Electro-Galvanized Carbon Steel
ORDERING: Specify figure number, size, flange width, flange thickness, material and
finish. (Order installation hardware separately.)
MAX FLANGE WEIGHT EACH lbs - FLANGE WIDTH in MAX. REC.
SIZE TxW A B C D THICKNESS 4 5 51⁄2 6 61⁄2 7 8 LOAD, LBS.
2 ⁄4 x 11⁄2
1 1
⁄2 4 13⁄4 1
⁄2 2.0 2.1 2.2 2.2 2.3 2.3 2.4 850
3 ⁄8 x 11⁄2
3 5
⁄8 41⁄2 2 1
⁄2 2.9 3.1 3.3 3.3 3.5 3.5 3.7 1100
4 3
⁄8 x 2 3
⁄4 41⁄2 1 1
⁄2 3.9 4.1 4.3 4.3 4.5 4.5 4.7 1500
5 Std 5 1 ⁄2
1
1
⁄2 x 2 7
⁄8 1
⁄2 6.0† 6.2† 6.3 6.3 6.6 6.6 6.9 2600
5 Box † 5 2
6 Std 5 3
⁄4
1
⁄2 x 21⁄2 1 5
⁄8 8.0† 8.7† 9.1† 8.0 8.4 8.4 8.8 4300
6 Box † 51⁄4 2
Notes:
1. For flange widths greater than 8” use FIG. #695.
2. B dimension may vary 1⁄4” due to flange thickness variations.
3. When ordering, flange width and flange thickness may be specified by the AISC W-Shape or S-shape designation, e.g., W8x35.

46
FIG. 680 Center Beam Clamp
SERVICE: To hang piping with a threaded rod from the bottom center of wide
flange beams (W-Shape) or American standard beams (S-Shape).
Permits horizontal pipe movement through hanger rod rotation. For
hanger assemblies loaded by static tensile forces from piping or similar
services.
MATERIAL: Carbon Steel meeting ASTM: A36, A500 Gr B, A307 Gr A and A563 Gr A
Stainless Steel Type 304 and 316 meeting ASTM: A240, A312, F593 and F594
350ºF for Electro-Galvanized Carbon Steel
ORDERING: Specify figure number, size, flange width, flange thickness, material and
finish. (Order installation hardware separately.)
FLANGE WEIGHT EACH, LBS.
WIDTH MAX THK SIZE 2 SIZE 5

4 1
⁄2 1.1 3.8
5 5
⁄8 1.2 4.1
51⁄2 5
⁄8 1.3 4.4
6 3
⁄4 1.3 4.4
61⁄2 3
⁄4 1.4 4.7
7 7
⁄8 1.4 4.7
8 7
⁄8 3.3 5.0
9 1 3.7 7.0
10 1 4.1 7.5
12 1 4.9 10.1
REC. MAX. MAX. REC.
SIZE FLANGE TXW A B C D E ROD ROD LOAD, LBS.
4 to 7 1⁄4 x 11⁄4 11⁄8
2 1
⁄2 /8
5 5
/8 0.840 /2
1 3
/4 1000
8 to 12 3⁄8 x 2 13⁄8
4 to 10 1⁄2 x 2
5 2 3
⁄4 /8
7
1 1.050 /4
3
1 3000
12 1
⁄2 x 3
Notes:
1. For flange widths greater than 12” use FIG. #695.
2. When ordering, flange width and flange thickness may be specified by the AISC W-Shape or S-shape designation, e.g., W8x35.
3. Maximum hanger rod-in-plane and out-of-plane rotation resultant ≤ 4º per MSS SP-58. Pipe attachment shall provide rotation.
4. Recommended rod size based on maximum load. Maximum rod size based on dimension “C” and FIG. #740 Weldless Eye Nut bail size.

47
FIG. 695 Beam Clamp Assembly
SERVICE: To hang piping with a single threaded rod from the bottom center of wide
flange beams (W-shape) or American standard beams (S-shape). Provides
vertical hanger rod adjustment. Permits horizontal pipe movement through
hanger rod rotation. For hanger assemblies loaded by static tensile forces
from piping or similar services.
MATERIAL: Carbon Steel meeting ASTM: A36, A307 Gr A, A563 Gr A
Stainless Steel Type 304 and 316 meeting ASTM: A240, F593, and F594
STANDARDS: MSS SP-58 Type 28 and Type 29, FS WW-H-171E Type 28 and Type 29
ORDERING: Specify figure number, size, flange width, flange thickness, rod size, material
and finish. (Order FIG. #740 Weldless Eye Nut and hardware separately.)
MAX FLG FLG MAX TAKE WEIGHT MAX. REC.
SIZE THK WIDTH ROD OUT EACH, LBS. LOAD, LBS.
1 5
/8 4 to 8 3
/4 11
⁄16 7.2 3230
2 5
/8 7 to 15 3
/4 11
⁄16 13.6 3230
3 3
/4 4 to 8 1 11
⁄16 9.8 5900
4 3
/4 7 to 15 1 11
⁄16 17.4 5900
5 1 5 to 9 11/2 111⁄16 25.5 13800
6 1 8 to 16 11/2 111⁄16 42.8 13800
DIMENSION B (±1⁄4”)
FLANGE WIDTH
SIZE
4 5 6 7 8 9 10 11 12 13 14 15 16
1 5 ⁄16
9
5 ⁄8
3
5 ⁄16
3
4 ⁄16
15
4 ⁄8
3
- - - - - - - -
2 - - - 915⁄16 913⁄16 95⁄8 93⁄8 91⁄8 813⁄16 87⁄16 81⁄16 75⁄8 -
3 61⁄2 65⁄16 61⁄8 57⁄8 55⁄16 - - - - - - - -
4 - - - 107⁄8 103⁄4 109⁄16 105⁄16 101⁄16 93⁄4 93⁄8 9 89⁄16 -
5 - 85⁄8 83⁄8 81⁄16 75⁄8 73⁄16 - - - - - - -
6 - - - - 127⁄8 123⁄4 129⁄16 123⁄8 121⁄8 117⁄8 117⁄16 111⁄8 109⁄16
Notes:
1. When ordering, flange width and flange thickness may be specified by the AISC W-shape or S-shape designation, e.g., W8x35.
2. Hanger rod in-plane and out-of-plane rotation resultant shall be ≤ 4º per MSS SP-58.
3. Maximum load based on FIG. #755 Continuous Threaded Rod. Smaller rod sizes may be used. See FIG. #755 for load rating.
4. Installation: Prior to tightening, cross rod shall sit on both spacers. Tighten nuts until cross rod bends slightly. Lock washers may not
flatten.

48
FIG. 685 Malleable Beam Clamp

FIG. 690 Malleable Beam Clamp w/ Extension Piece
SERVICE: For the attachment to bottom flange of I-beam and wide flange beams
where flange widths are from 23/8” - 7” and the flange thickness does not
exceed .60 inches.
MATERIAL: Malleable Iron and Steel
STANDARDS: MSS SP-58 Type 30 (FIG. #690)
ORDERING: Specify figure number, rod size and finish. FIG. #685
ROD SIZE ROD TAKEOUT FOR WIDTH OF BEAM FLANGE “B” BOLT WEIGHT MAX. REC.
A 23/8 3 4 5 6 7 DIA. EACH, LBS. LOAD, LBS.
CLAMP ONLY 31/2 37/16 35/16 215/16 29/16 17/8 7
/16 2.20 1365
3
/8 43/4 411/16 49/16 43/16 313/16 31/8 7
/16 2.42 610
1
/2 47/8 413/16 411/16 45/16 315/16 31/4 7
/16 2.63 1130
5
/8 415/16 47/8 43/4 43/8 4 35/16 7
/16 2.67 1365
3
/4 53/16 51/8 5 45/8 41/4 39/16 7
/16 2.87 1365
7
/8 51/4 53/16 51/16 411/16 45/16 35/8 7
/16 3.01 1365
FIG. #690
FIG. 700 Light Welded Steel Bracket
SERVICE: For the support of loads up to 750 Lbs. Constructed of facing angle irons
with 1” space between. This bracket provides maximum lateral adjustment
when carrying or suspending pipe.
ORDERING: Specify figure number, size, material and finish.
CARBON STEEL
SIZE ANGLE SIZE WEIGHT
C-C A E H B L W
NO. S EACH, LBS.
0 111/2 9 2 13
/16 3
/4 13 1 x 1 x 3/16 3 6.63
1 151/2 13 2 13
/16 3
/4 17 1 x 1 x 3/16 3 9.33
2 211/2 19 2 13
/16 3
/4 23 1 x 1 x 3/16 3 13.34
STAINLESS STEEL
C-C A E H B L W
NO. S EACH, LBS.
0 111/2 9 2 13
/16 3
/4 13 1 x 1 x 3/16 3 7.00
1 151/2 13 2 13
/16 3
/4 17 1 x 1 x 3/16 3 9.62
2 211/2 19 2 13
/16 3
/4 23 1 x 1 x 3/16 3 13.73
NOTE: Stainless steel dimensions may change due to availability of stainless steel angle.

49
FIG. 705 Medium Welded Steel Bracket
SERVICE: For the support of loads up to 1,500 Lbs. Constructed of facing angle irons
with 1” space between. This bracket provides maximum lateral adjustment
when carrying or suspending pipe.
CARBON STEEL
C-C A E H B L W
NO. S EACH, LBS.
0 151/2 12 21/2 13
/16 11/4 18 11/2 x 11/2 x 3/16 4 15.67
1 211/2 18 21/2 13
/16 11/4 24 13/4 x 13/4 x 3/16 41/2 25.90
2 271/2 24 21/2 13
/16 11/4 30 2 x 2 x 1/4 5 44.87
STAINLESS STEEL
C-C A E H B L W
NO. S EACH, LBS.
0 151/2 12 21/2 13
/16 11/4 18 11/2 x 11/2 x 3/16 4 16.50
1 211/2 18 21/2 13
/16 11/4 24 2 x 2 x 1/4 5 35.00
2 271/2 24 21/2 13
/16 11/4 30 2 x 2 x 1/4 5 46.00
FIG. 710 Heavy Welded Steel Bracket
SERVICE: For the support of loads up to 3,000 Lbs. Constructed of facing angle
irons with 1” space between. This bracket provides maximum lateral
adjustment when carrying or suspending pipe.
CARBON STEEL
C-C A B E F H L W
NO. S EACH, LBS.
0 151/2 12 13/8 23/4 1 Hole /16
13
18 2 x 11/2 x 1/4 4 25.00
1 213/8 18 13/8 23/4 23/4 /16
15
24 2 x 2 x 1/4 5 38.00
2 271/2 24 11/4 23/4 21/2 11/8 30 21/2 x 2 x 3/8 5 69.00
3 331/4 30 11/2 3 21/2 11/8 36 21/2 x 2 x 3/8 5 82.10
4 39 36 11/2 3 31/2 11/8 42 31/2 x 21/2 x 3/8 6 130.00
5 46 42 2 3 /2 31/2
1
11/8 50 31/2 x 21/2 x 3/8 6 162.00
STAINLESS STEEL
C-C A B E F H L W
NO. S EACH, LBS.
0 151/2 12 13/8 23/4 1 Hole /16
13
18 2 x 2 x 1/4 5 27.45
1 213/8 18 13/8 23/4 23/4 /16
15
24 2 x 2 x 1/4 5 40.00
2 271/2 24 11/4 23/4 21/2 11/8 30 2 /2 x 21/2 x 3/8
1
6 74.00
3 331/4 30 11/2 3 21/2 11/8 36 21/2 x 21/2 x 3/8 6 95.00
4 39 36 11/2 3 31/2 11/8 42 31/2 x 31/2 x 3/8 8 162.00
5 46 42 2 3 /2 31/2
1
11/8 50 31/2 x 31/2 x 3/8 8 193.00

50
FIG. 715 Light Welded Steel Bracket

FIG. 720 Side Clip
SERVICE: For the suspension of hanger rods from steel columns or walls.
Using a FIG. #720 clip which consists of two steel plates joined
by a bolt and nut in one end, rod can be suspended at any point
along the length of the bracket, thus providing horizontal
adjustment.
ORDERING: Specify figure number, bracket size number, clip number (if
required) material and finish. (Piping suspended from FIG. #720
clip must not exceed 3½” in diameter. Clip must be ordered
separately.)
FIG. #715
BRACKET HOLE STOCK SIZE WEIGHT MAX. REC.
B C-C L
SIZE SIZE S EACH, LBS. LOAD, LBS.
1 8 61/2 13
/16 9 3
/8 x 2 4.2 750
2 12 101/2 13
/16 13 3
/8 x 2 6.5 750
3 18 161/2 13
/16 19 3
/8 x 2 9.4 750
FIG. #720
CLIP PIPE ROD SIZE WEIGHT
NUMBER SIZE A EACH, LBS.
1 /4 TO 2
3
/8
3
0.80
2 2 /2 TO 31/2
1
/2
1
1.24
FIG. 730 Turnbuckle
SERVICE: For providing adjustment up to 6” for heavy loads.

ORDERING: Specify figure number, rod size and finish.
ROD BODY WEIGHT MAX. REC. LOAD,
SIZE LENGTH EACH, LBS. LBS. 650°F
3
/8 71/8 0.42 1200
1
/2 79/16 0.65 2200
5
/8 77/8 0.98 3500
3
/4 81/8 1.45 5200
7
/8 85/8 1.85 7200
1 87/8 2.60 9300
11/8 91/8 4.06 11600
11/4 91/8 4.00 15200
11/2 93/4 6.15 21000

51
FIG. 735 Forged Steel Clevis
SERVICE: For use on high temperature piping installations.

ORDERING: Specify figure number, size, rod tapping size, pin hole size,
pin size (if required), grip size and finish.
ROD SIZE GRIP BODY PIN SIZE WEIGHT MAX. REC. LOAD,
A D T N W
(TAP) SIZE P EACH, LBS. LBS. 650°F
3
/8 1
/2 1
/2 610
1
/2 1
/2 #2 39/16 17/16 /16
5 5
/8 11/16 5
/8 1.7 1130
5
/8 5
/8 3
/4 1810
3
/4 3
/4 7
/8 2710
#2.5 4 21/2 /16
5
1 11/4 2.5
7
/8 7
/8 1 3770
1 1 11/8 4960
11/8 11/8 #3 51/16 3 1
/2 11/4 11/2 11/4 4.0 6230
11/4 11/4 11/2 8000
11/2 11/2 #3.5 6 31/2 1
/2 11/2 13/4 15/8 6.0 11630
FIG. 740 Weldless Eye Nut
SERVICE: Recommended for use on pipe hanger assemblies between pipe attachment
and structural attachment. Provides vertical hanger rod adjustment. Permits
horizontal pipe movement through hanger rod rotation. For hanger assemblies
loaded by static and dynamic tensile forces from piping or similar services.
MATERIAL: Carbon Steel meeting AISI C-1030
Stainless Steel Type 316 meeting ASTM A182
ROD WEIGHT MAX. REC.
B C D E F G H J
3
/8 0.63 730
1
/2 0.61 1350
/16
11
1 /2
1
2 /4
1
3 /16
3
1 /16
3
2 /2
1
1 /8
3
5
/8 0.59 2160
3
/4 0.56 3230
7
/8 1.72 4480
1 2 31/4 43/8 111/16 25/8 /4
3
115/16
1 1.67 5900
11/8 3.64 7420
11/4 11/4 21/2 41/4 55/8 113/16 33/8 1 23/8 3.55 9500
11/2 3.45 13800
Note:
1. Hanger rod in-plane and out-of-plane rotation resultant shall be ≤ 4º per MSS SP-58.

52
FIG. 744 Swivel Hanger Male/Female
SERVICE: For installation where a universal movement of the piping

is desirable.
ORDERING: Specify figure number and rod size. (Sizes 3/8” and 1/2” use
a Hex Nut welded to round bar on the female end. Sizes
5
/8” and 3/4” use a Weldless Eye Nut on the female end.)
ROD SIZE B C D WEIGHT MAX. REC. C
A EACH, LBS. LOAD, LBS. A
3
/8 3
/8 2 /4
3
1 0.28 610
1
/2 1
/2 23/4 1 0.36 1130
D
5
/8 5
/8 53/16 11/2 1.00 1810
3
/4 3
/4 53/16 11/2 1.30 2710 B
FIG. 755 Continuous Threaded Rod
SERVICE: Recommended for use on hanging pipe support assemblies between pipe attachment and
structural attachment. Continuous rolled United National Course (UNC) Class 1A thread
form available in 6ft, 10ft and 12ft lengths.
MATERIAL: Carbon Steel meeting ASTM A36
Stainless Steel Type 304 and 316 meeting ASTM F593
FINISH: Black, Electro-Galvanized meeting ASTM B633 or Hot-Dip Galvanized meeting ASTM A153
350ºF for Electro-Galvanized and Hot-Dip Galvanized Carbon Steel
ORDERING: Specify figure number, rod size, length, material and finish.
ROD ROOT AREA WEIGHT PER MAX. REC.
SIZE THREAD, IN2 FOOT, LBS. LOAD, LBS.
/41
0.027 0.12 280
5
/16 0.045 0.19 480
3
/8 0.068 0.29 730
1
/2 0.126 0.54 1350
5
/8 0.202 0.83 2160
3
/4 0.302 1.25 3230
7
/8 0.419 1.70 4480
1 0.551 2.23 5900
11/8 0.693 2.81 7420
11/4 0.890 3.54 9500
13/8 1.054 4.23 11290
11/2 1.290 5.12 13800
13/4 1.740 6.92 18600
2 2.300 9.09 24600
Notes:
1. Maximum recommended load based on MSS SP-58 with ultimate strength of 50000 psi, a safety factor of 3.5 and a 25% reduction for
installation and service conditions equating to an allowable stress of 10700 psi loaded in tension.
2. Minimum 3⁄8” rod size per MSS SP-58.
3. Root area in accordance with ASME B1.1.
4. United National Fine (UNF) thread form available upon request.

53
FIG. 770 Rod Coupling
SERVICE: For connecting lengths of threaded rod.

ORDERING: Specify figure number, rod tapping size, material and finish.
ROD WEIGHT PER MAX. REC.
LENGTH
SIZE 100, LBS. LOAD, LBS.
1
/4 /8
7
9 240
5
/16 13/4 8 300
3
/8 13/4 13 610
1
/2 13/4 15 1130
5
/8 21/8 18 1810
3
/4 21/4 33 2710
7
/8 21/2 72 3770
1 21/2 78 4960
11/8 3 120 6230
11/4 3 143 8000
11/2 4 190 11630
FIG. 775 Reducing Rod Coupling
SERVICE: For connecting lengths of threaded rod.

ORDERING: Specify figure number, rod tapping size, material and finish.
WEIGHT PER MAX. REC.
ROD SIZE LENGTH 100, LBS. LOAD, LBS.
3
/8 x 1/4 1 11 225
1
/2 x 3/8 11/4 12 610
5
/8 x 1/2 11/4 16 1130
3
/4 x 5/8 11/2 31 1810
7
/8 x 3/4 13/4 39 2710
1 x 7/8 2 41 3770
FIG. 780 Hex Head Machine Bolt
SERVICE: For use as a fastening device.

ORDERING: Specify figure number, bolt size, material and finish. (Length of bolt
is measured from under the head to the extreme point. Sizes as
shown are carried in stock, other sizes are also available.)
WEIGHT PER 100, LBS.
BOLT LENGTH OF BOLT
DIA. 11/2 13/4 2 21/4 21/2 23/4 3 31/4 31/2 33/4 4 41/2 5 51/2 6
/8
3
9 10 11 - - - - - - - - - - - -
1
/2 18 20 21 22 24 25 27 - - - - - - - -
5
/8 31 33 35 37 39 41 43 46 48 50 52 56 61 65 69
3
/4 49 52 55 58 61 64 67 70 73 76 80 86 92 98 105
7
/8 - - - - 89 93 98 102 106 110 115 123 131 140 148
1 - - - - - 128 134 139 145 150 156 167 178 189 200
11/8 - - - - - - - - 193 - 207 221 235 249 263
11/4 - - - - - - - - - - - - 302 320 337

54
FIG. 785 Finished Hex Nuts

FIG. 790 Heavy Duty Hex Nuts

ROD WEIGHT PER 100, LBS.
SIZE FIG. #785 FIG. #790
1
/4 0.74 1.20
3
/8 1.60 3.20
1
/2 3.75 6.60
5
/8 7.33 12.00
3
/4 11.90 19.00
7
/8 19.00 30.00
1 28.30 43.00
11/8 40.30 59.00
11/4 54.30 79.00
13/8 73.00 102.00
11/2 94.30 131.00
FIG. 795 Round Steel Washers

ROD HOLE WEIGHT PER
O.D.
SIZE SIZE 100, LBS.
/4
1
/4 3 5
/16 0.67
/8
3
1 7
/16 1.50
1
/2 13/8 9
/16 3.90
5
/8 13/4 11
/16 7.80
3
/4 2 13
/16 11.00
7
/8 21/4 15
/16 15.00
1 21/2 11/16 19.00
11/8 23/4 11/4 22.00
11/4 3 13/8 26.00
11/2 31/2 15/8 38.00
FIG. 800 Split Lock Washers

ROD STEEL STEEL WEIGHT PER
I.D.
SIZE WIDTH THICKNESS 100, LBS.
3
/8 7
/16 0.14 0.09 7
1
/2 9
/16 0.17 0.13 15
5
/8 11
/16 0.20 0.16 26
3
/4 13
/16 0.23 0.19 43

55
FIG. 805 Steel Washer Plate
SERVICE: For use as a heavy duty washer to suspend hanger rods.

ORDERING: Specify figure number, rod tapping size, material and finish. (Steel in 1/4” thickness
is kept in stock for all rod sizes. Special size and thickness available upon request.)
ROD STOCK WEIGHT
SIZE SIZE EACH, LBS.
3
/8 2 x 2 x 1/4 0.28
1
/2 2 x 2 x 1/4 0.28
3
/8 3 x 3 x 1/4 0.62
1
/2 3 x 3 x 1/4 0.62
5
/8 3 x 3 x 1/4 0.62
3
/4 3 x 3 x 1/4 0.62
3
/8 4 x 4 x 1/4 1.05
1
/2 4 x 4 x 1/4 1.05
5
/8 4 x 4 x 1/4 1.05
3
/4 4 x 4 x 1/4 1.05
7
/8 4 x 4 x 1/4 1.05
FIG. 810 Fender Washers
SERVICE: For producing a greater bearing surface.

ROD HOLE WEIGHT PER
O.D.
SIZE SIZE 100, LBS.
1
/4 11/4 9
/32 2.2
1
/4 11/2 9
/32 3.2
3
/8 11/4 13
/32 2.0
3
/8 11/2 13
/32 3.0
1
/2 2 17
/32 5.5
FIG. 816 Round Head Machine Screws
SERVICE: For use with the FIG. #302 shield with hole.
ORDERING: Specify figure number and size.
WEIGHT PER
SIZE 100, LBS.
1
/4 x 3/4 1.5
/4 x 1
1
1.8
1
/4 x 11/4 1.9

56
FIG. 830 Pipe Sleeve
SERVICE: For attaching to concrete forms to provide a smooth sealable channel

for piping, eliminating the need to core drill. Pipe sleeves are cut from
standard weight pipe with optional lugs to facilitate fastening.
ORDERING: Specify figure number, nominal pipe size A, length, with or without lugs,
material and finish.
Shown with
optional lugs.
FIG. 835 Nailing Sleeve
SERVICE: For attaching to roof deck to provide a channel for piping,

eliminating the need to core drill. Sleeves are made in all
heights and diameters with optional tabs to facilitate
fastening and an optional cap to keep out wet cement
until pipe installation.
MATERIAL: Galvanized Sheet Metal or 304/316 Stainless Steel
FINISH: Galvanized
ORDERING: Specify figure number, diameter, height, type, with or
without tabs and material.
Cap & Tabs Tabs Only

TYPE 1 TYPE 2 TYPE 3 TYPE 4 TYPE 5 TYPE 6
Stapled Locking Finger Split, Butt Split, Metal Deck
or Tabs Locks Edges Overlap Flange
Spot-Welded 100 pcs Min.
FIG. 840 Waterproof Sleeve
SERVICE: For installing in concrete forms to provide a smooth, sealable channel for
piping. Waterproof sleeves are cut from standard weight pipe and are
furnished with a continuously welded water stop made from 1/4” steel plate,
to prevent the migration of water around the outside of the sleeve.
ORDERING: Specify figure number, nominal pipe size A, ring center line B, length,
material and finish.

57
FIG. 845 ®
Wood-Knocker II+
SERVICE: To provide a pre-positioned hanger rod attachment to the underside of concrete slabs
on wood forms. Used as a cast-in-place concrete anchor in 3,000 psi minimum
compressive strength normal and lightweight, cracked and uncracked concrete loaded
by static and occasional tensile and shear forces from piping or similar services.
MATERIAL: Carbon Steel meeting AISI 1008 and Engineered Plastic (Polypropylene)
FINISH: Electro-Galvanized meeting ASTM B633
MAX TEMP: 200ºF
APPROVALS: FM, UL, ICC-ES ESR-3657, IBC 2012
ORDERING: Specify figure number and anchor size.
ANCHOR COLOR WEIGHT
SIZE CODE EACH, LBS.
3
/8 GREEN 0.248
1
/2 YELLOW 0.220
5
/8 RED 0.356
3
/4 PURPLE 0.348
NOTE: See Powers Fasteners, Wood-Knocker for maximum recommended loads and additional details.
FIG. 850 Bang-It TM
SERVICE: To provide a pre-positioned hanger rod attachment to the underside of concrete slabs
on metal form decks. Used as a cast-in-place concrete anchor in 3,000 psi minimum
compressive strength normal and lightweight, cracked and uncracked concrete loaded
by static and occasional tensile and shear forces from piping or similar services.
MATERIAL: Carbon Steel meeting AISI 1008 and Engineered Plastic (Polypropylene)
FINISH: Electro-Galvanized meeting ASTM B633
MAX TEMP: 200ºF
APPROVALS: FM, UL, ICC-ES ESR-3657, IBC 2012
ORDERING: Specify figure number and anchor size.
ANCHOR COLOR WEIGHT
SIZE CODE EACH, LBS.
3
/8 GREEN 0.408
1
/2 YELLOW 0.384
5
/8 RED 0.759
3
/4 PURPLE 0.715
NOTE: See Powers Fasteners, Bang-It for maximum recommended loads and additional details.
FIG. 855 Hangermate®+
SERVICE: For suspending threaded rod vertically overhead in pipe hanging,

fire protection, electrical conduit and cable-tray applications.
Steel Hangermate
APPROVALS: FM, UL
ORDERING: Specify figure number.
FIG SIZE ROD MOUNT SCREW WEIGHT Wood Hangermate
TYPE LENGTH
# # SIZE DIRECTION SIZE EACH, LBS.
Vertical Mount
7159 PFM2231200 STEEL 3
/8 VERTICAL 1
/4 11⁄2 0.075
7164 PFM2251300 WOOD 1
/2 VERTICAL 5
⁄16 21⁄2 0.082
7165 PFM2251100 WOOD 3
/8 VERTICAL 1
/4 2 0.073
7170 PFM2261100 WOOD 3
/8 SIDE 1
/4 2 0.073 Wood Hangermate
7173 PFM2217173 CONCRETE 3
/8 VERTICAL 1
/4 11⁄2 0.070 Side Mount
7175 THD50234RH CONCRETE 1
/2 VERTICAL 1
/2 23⁄4 0.082
NOTE: Refer to Powers Fasteners, Hangermate®+ for maximum recommended loads and
additional details. Refer to Simpson Strong-Tie, Titen HD for additional details on FIG #7175.
Concrete Hangermate
58
FIG. 860 Wedge Anchor
SERVICE: For use in solid concrete and grout filled masonry.

ORDERING: Specify figure number, rod size, length and material.
WEIGHT PER WEIGHT PER
SIZE SIZE
100, LBS. 100, LBS.
1
/4 x 13/4 3.00 1
/2 x 51/2 30.80
1
/4 x 21/4 4.00 1
/2 x 7 38.00
1
/4 x 31/4 5.00 5
/8 x 31/2 36.00
3
/8 x 21/4 8.00 5
/8 x 41/2 41.00
3
/8 x 23/4 9.00 5
/8 x 6 53.00
3
/8 x 3 10.00 3
/4 x 43/4 68.00
3
/8 x 33/4 13.00 3
/4 x 51/2 76.00
3
/8 x 5 15.00 3
/4 x 61/4 91.00
1
/2 x 23/4 19.00 3
/4 x 7 91.00
1
/2 x 33/4 23.00 7
/8 x 6 128.00
1
/2 x 41/2 27.00 1x6 168.00
FIG. 865 Sleeve Anchor w/ Coupling

FIG. 867 Sleeve Anchor
SERVICE: For anchoring to concrete and masonry substrates.

Suitable for solid and hollow base materials.
MATERIAL: Carbon Steel FIG. #865
ORDERING: Specify figure number and size. FIG. #775 Reducing
Rod Coupling must be ordered separately for FIG. #867
Sleeve Anchor.
FIG. #865 FIG. #867
DRILL MIN. WEIGHT PER DRILL MIN. WEIGHT PER FIG. #867
SIZE SIZE
SIZE EMBED 100, LBS. SIZE EMBED 100, LBS.
3
/8 X 17/8 /8
3
15/8 9.0 /8 X 21/2
5 5
/8 2 25.5
1
/2 X 21/4 /2
1
21/4 21.0 /4 X 23/4
3 3
/4 21/4 46.0
NOTE: Length shown is measured from end of bolt to bottom of washer.
FIG. 874 Mini Drop-In Anchor

FIG. 877 Mini Drop-In Setting Tool
SERVICE: For anchoring into solid concrete and hollow core concrete plank.
ORDERING: Specify figure number and size. FIG. #874
DRILL MIN. THREAD WEIGHT PER
SIZE SIZE DEPTH DEPTH 100, LBS.
3
/8 1
/2 /4
3
/32
13
0.04 FIG. #877
1
/2 5
/8 1 /8
5
0.06

59
FIG. 875 Drop-In Anchor

FIG. 876 Drop-In Setting Tool
SERVICE: For anchoring into solid concrete.

ORDERING: Specify figure number, size and material. FIG. #875
MIN. CONCRETE COMPRESSION
ANCHOR DRILL MIN. WEIGHT PER STRENGTH 4,000 psi
SIZE LENGTH SIZE EMBED 100, LBS.
TENSION, LBS SHEAR, LBS FIG. #876
1
/4 1 3
/8 1 2.6 495 530
3
/8 19/16 1
/2 19/16 6.8 1045 1145
1
/2 2 5
/8 2 11.6 1440 1600
5
/8 21/2 7
/8 21/2 31.2 1860 3095
3
/4 33/16 1 33/16 47.6 3600 3920
NOTE: Allowable load capacities listed are calculated using an applied
safety factor of 4.0.
FIG. 878 Hammer Drive Anchor
SERVICE: For anchoring into solid concrete, block or brick.

MATERIAL: Carbon Steel drive nail with Zamac Alloy body
DRILL WEIGHT PER
SIZE SIZE 100, LBS.
1
/4 x 3/4 1
/4 1.50
/4 x 1
1 1
/4 1.75
1
/4 x 11/4 1
/4 2.25
1
/4 x 11/2 1
/4 2.50
1
/4 x 2 1
/4 3.00
FIG. 880 Spring Wing Toggle w/ Bolt

FIG. 885 Spring Wing Toggle Head Only
SERVICE: For use as a fastener for hollow walls.

DRILL WEIGHT PER 100, LBS. MAX. REC. LOAD, LBS
SIZE SIZE TOGGLE WITH BOLT BOLT ONLY TENSION SHEAR
1
/4 x 3 5
/8 6.5 3 70 120
1
/4 x 4 5
/8 7.5 3 70 120
1
/4 x 6 5
/8 9.5 3 70 120 FIG. #885 FIG. #880
3
/8 x 3 7
/8 16.0 7 140 140
3
/8 x 4 7
/8 18.0 7 140 140
3
/8 x 6 7
/8 23.0 7 140 140
1
/2 x 4 11/4 42.0 9 230 160
1
/2 x 6 11/4 50.0 9 230 160

60
FIG. 900 Neoprene-In-Shear Hanger
ISOLATOR MAX. REC. DIMENSIONS

SIZE LOAD, LBS. DEFLECTION A B C D E
BRD-1-A 60
BRD-1-B 130
0.50 4 27/8 21/2 1/2 17/8
BRD-1-C 250
BRD-1-D 430
BRD-2-A 380
BRD-2-B 520
0.50 51/2 33/4 4 /4 23/8
3
BRD-2-C 840
BRD-2-D 1070
BRD-3-A 750
BRD-3-B 1350
0.50 61/4 41/4 53/8 1 23/8
BRD-3-C 1900
BRD-3-D 3050
FIG. 901 Spring Hanger
ISOLATOR RATED LOAD SOLID

SIZE LBS. AT 1” DEFL. LOAD, LBS.
BS-50 50 126
BS-100 100 207
BS-150 150 263
BS-200 200 348
BS-300 300 500
BS-400 400 605
BS-500 500 750
BS-600 600 891
BS-700 700 1138
BS-800 800 1155
BS-1000 1000 1452
FIG. 902 Neoprene-In-Shear Spring Hanger
ISOLATOR RATED LOAD SOLID DIMENSIONS

SIZE LBS. AT 1” DEFL. LOAD, LBS. A B C D E F G
BSRA-1-15 15 27
BSRA-1-25 25 39
BSRA-1-50 50 83
BSRA-1-100 100 160
31/2 21/2 71/8 3 /2 2 17/8
1
BSRA-1-150 150 242
BSRA-1-200 200 293
BSRA-1-300 300 442
BSRA-1-400 400 585
BSRA-1-500 500 782
BSRA-1-600 600 925
/4
3
BSRA-1-800 800 1257
BSRA-1-1000 1000 1565
41/2 47/8 11 43/8 31/4 23/8
BSRA-1-1200 1200 1829
BSRA-1-1400 1400 2131
1
BSRA-1-1600 1600 2419
BSRA-1-1800 1800 2662

61
FIG. 950 Pipe Slide, Guide and Anchor
SERVICE: To support pipe while providing axial movement combined with lateral
movement, lateral guidance, uplift restraint and/or anchorage. Slides, guides
and uplift restraints to be welded or bolted to structure and welded or
clamped to the pipe. Glass filled virgin Teflon™ (PTFE) slide bearing provides
low coefficient of friction to reduce stress on the pipe and supporting
structure. Anchors to be continuously welded to pipe and structure only.
Slide Bearing: PTFE-to-PTFE, average coefficient of friction = 0.06
MAX TEMP: 650ºF at pipe wall
300ºF at PTFE bearing.
ORDERING: Specify figure number, type, pipe size, pipe attachment type and finish.
(Order mounting hardware separately.)
BASE DIMENSIONS
DIMENSIONAL DATA TYPES: S, G, U
PIPE PIPE C D
A Bc SIZE
SIZE
2-5 4 51/16 2 - 12 7 81⁄2
6-8 4 53/16 14 - 24 91⁄2 11
10 - 12 4 55/16
14 - 16 61/2 55/16
18 - 24 61/2 57/16
MAXIMUM RECOMMENDED LOADS Notes:

1. Special fabricated tee and base available for specified axial and lateral travel,
PIPE VERTICAL VERTICAL LATERAL
TYPE AXIAL insulation banding slots, heat loss notches and/or grade 304 and 316 stainless
SIZE DOWN UP
steel. Provide performance criteria and dimensions A, BOP, C, D and/or L.
S 2 - 24 8000 n/a n/a n/a 2. For PTFE bearing temperatures 300ºF to 500ºF, specify high temperature
2-6 8000 n/a 1000 n/a bearing adhesive. Available in black finish only over 350ºF.
G 3. Alternative PTFE-on-stainless steel slide bearing option available.
8 - 24 8000 n/a 2000 n/a
4. Weld in accordance with AWS D1.1 with 70000 psi filler metal. Minimum weld
2-6 8000 800 1000 n/a sizes shown. Tee-to-pipe and base-to-structure welds may be continuous.
U
8 - 24 8000 800 2000 n/a 5. Anchor loads for standard weight carbon steel pipe at design conditions 400 psi
2-6 4000 800 1000 2000 and 500ºF. Corrosion allowance 1⁄32” for pipe sizes ≤ 6” and 1⁄16” for sizes ≥ 8”.
A
8 - 24 8000 800 2000 5000

62
FIG. 955S H-Slide

±5” Axial Movement, ±1” Lateral Movement
SERVICE: To support pipe while providing large axial movement and moderate lateral
movement. Pad to be welded to structure and body welded to pipe. Slide
bearing provides low coefficient of friction between body and pad to reduce
stress on the pipe and supporting structure.
Stainless Steel meeting ASTM A240 Type 304 and 316
Slide Bearing: PTFE-on-PTFE, 3/32” thick glass filled PTFE bonded to 10 ga.
back-up plate, 2000 psi compressive strength at 70°F (Note 2)
FINISH: Black and Hot-Dip Galvanized meeting ASTM A123
MAX TEMP: At Pipe Wall: 650ºF for Black, 350ºF for Hot-Dip Galvanized.
At PTFE Bearing 300°F (Note 2 & 3).
STANDARDS: MSS SP-58 Type 35, FS A-A-1192A Type 35
ORDERING: Specify figure number, pipe size, and finish (example: 955S-16-HDG).
PIPE PIPE WEIGHT VERTICAL

SIZE cL BOP A B EACH, LBS DOWN LOAD
6 8 411/16 10 31/2 24 12000
8 9 411/16 10 31/2 24 12000
10 97/8 41/2 121/2 31/2 35 16000
12 11 45/8 121/2 31/2 35 16000
14 111/8 41/8 141/2 3 51 16000
16 123/8 43/8 141/2 3 51 16000
18 127/8 37/8 17 3 56 16000
20 14 4 17 3 56 16000
24 157/8 37/8 19 3 65 24000
30 197/8 47/8 21 4 78 24000
36 231/4 51/4 23 4 108 24000
NOTES:
1. Special fabricated configurations available upon request for options: pad bolted to structure, body clamped to pipe, specified bottom of
pipe (BOP), custom axial / lateral travel, insulation banding slots, heat loss notches, etc. Provide performance criteria and dimensions.
2. Allowable vertical load at 70°F bearing temperature. See Supplemental Data for load reduction factors at higher bearing temperatures.
3. For bearing temperatures 300°F to 500°F, specify High Temperature adhesive (-HT).
4. Pad may be seal welded to structure with all-around weld.
5. Body interchangeable with 955G, 955L, and 955U pads for same pipe size and “A” dimension.
6. See Fig 955 Supplemental Data for other structural attachment details, slide bearing information, etc.

63
FIG. 955G H-Guide

±5” Axial Movement, ±1⁄16” Lateral Movement
SERVICE: To support pipe while providing large axial movement and lateral guidance.
Pad to be welded to structure and body welded to pipe. Slide bearing
provides low coefficient of friction between body and pad to reduce stress
on the pipe and supporting structure.
At PTFE Bearing 300°F (Note 2 & 3)
ORDERING: Specify figure number, pipe size, and finish (example: 955G-16-HDG).
PIPE PIPE WEIGHT VERTICAL LATERAL

BOP A B
SIZE cL EACH, LBS DOWN LOAD LOAD
6 8 411/16 10 31/2 26 12000 3000
8 9 411/16 10 31/2 26 12000 3000
10 97/8 41/2 121/2 3 37 16000 4000
12 11 45/8 121/2 3 37 16000 4000
14 111/8 41/8 141/2 3 54 16000 4000
16 123/8 43/8 141/2 3 54 16000 4000
18 127/8 37/8 17 3 58 16000 4000
20 14 4 17 3 58 16000 4000
24 157/8 37/8 19 3 68 24000 6000
30 197/8 47/8 21 4 80 24000 6000
36 231/4 51/4 23 4 111 24000 6000
NOTES:
5. Body interchangeable with 955S, 955L, and 955U pads for same pipe size and “A” dimension.

64
FIG. 955L H-Slide w/ Lateral Stop

±5” Axial Movement, ±1” Guide Gap
SERVICE: To support pipe while providing large axial movement and moderate lateral
movement with guidance. Pad to be welded to structure and body welded
to pipe. Slide bearing provides low coefficient of friction between body and
pad to reduce stress on the pipe and supporting structure.
ORDERING: Specify figure number, pipe size, and finish (example: 955L-16-HDG).
PIPE PIPE WEIGHT VERTICAL LATERAL

BOP A B
SIZE cL EACH, LBS DOWN LOAD LOAD
6 8 411/16 10 31/2 26 12000 3000
8 9 411/16 10 31/2 26 12000 3000
10 97/8 41/2 121/2 31/2 38 16000 4000
12 11 45/8 121/2 31/2 38 16000 4000
14 111/8 41/8 141/2 3 54 16000 4000
16 123/8 43/8 141/2 3 54 16000 4000
18 127/8 37/8 17 3 59 16000 4000
20 14 4 17 3 59 16000 4000
24 157/8 37/8 19 3 68 24000 6000
30 197/8 47/8 21 4 81 24000 6000
36 231/4 51/4 23 4 112 24000 6000
NOTES:
5. Body interchangeable with 955S, 955G, and 955U pads for same pipe size and “A” dimension.

65
FIG. 955U H-Guide w/ Uplift Stop

±5” Axial Movement, ±1⁄16” Guide Gap, 1⁄2” Uplift Gap
SERVICE: To support pipe while providing large axial movement, lateral guidance, and
uplift restraint. Pad to be welded to structure and body welded to pipe.
Slide bearing provides low coefficient of friction between body and pad to
reduce stress on the pipe and supporting structure.
ORDERING: Specify figure number, pipe size, and finish (example: 955U-16-HDG).
PIPE PIPE BOP A B WEIGHT VERTICAL LATERAL UPLIFT

SIZE cL EACH, LBS DOWN LOAD LOAD LOAD
6 8 411/16 10 21/2 28 12000 3000 1200
8 9 411/16 10 21/2 28 12000 3000 1200
10 97/8 41/2 121/2 21/2 39 16000 4000 1600
12 11 45/8 121/2 21/2 39 16000 4000 1600
14 111/8 41/8 141/2 21/2 55 16000 4000 1600
16 123/8 43/8 141/2 21/2 55 16000 4000 1600
18 127/8 37/8 17 21/2 60 16000 4000 1600
20 14 4 17 21/2 60 16000 4000 1600
24 157/8 37/8 19 21/2 70 24000 6000 2400
30 197/8 47/8 21 31/2 82 24000 6000 2400
36 231/4 51/4 23 4 113 24000 6000 2400
NOTES:
5. Body interchangeable with 955S, 955G, and 955L pads for same pipe size and “A” dimension.

66
Finishes
National Pipe Hanger Corporation offers the following types of finishes on its products.
ELECTRO-GALVANIZED ZINC (ASTM B633) - This type of finish is suitable for indoor use in relatively dry areas.
The process deposits a coating of zinc on the steel or iron through the process of electrolysis. A coating of pure
zinc adheres to the steel or iron with a molecular bond.
PRE-GALVANIZED ZINC (ASTM A653) - This type of finish is recommended for extended exposure in dry or
mildly corrosive atmospheres. Also referred to as “mill galvanized,” the pre-galvanized zinc coating is produced
at the steel mill by continuously rolling steel coils or sheets through molten zinc. The material is then cut to size
for fabrication.
HOT-DIP GALVANIZED (ASTM A123 or ASTM A153) - This type of finish provides extended corrosion protection
for steel and iron products. It is recommended for prolonged outdoor exposure and will usually protect steel
and iron products in most atmospheric environments. After fabrication, the product is immersed in a bath of
molten liquid zinc where a metallurgical bond is created resulting in a tightly adherent zinc coating on all surfaces
including edges.
COPPER PLATING - This type of finish is used for identification purposes and generally not intended to provide
corrosion protection. It is recommended that a non-metallic coating, jacket or liner be used on hanger material
where the risk of galvanic corrosion is present.
COPPER-GARD - COPPER-GARD products offer corrosion protection due to the epoxy coating over Elec-
tro-Galvanized material. The alternative Copper Plating that has been done historically identifies the product
and is not intended for protection.
PVC - Polyvinyl Chloride or plastic coated products are recommended to prevent galvanic reaction between
dissimilar metals, provide corrosion resistance, and reduce noise and vibration.
SPECIAL COATING - Special finishes can be supplied per customer request.
67
Pipe Outside Diameter Chart
COPPER
NPS (IPS) PVC
SERVICE EXTRA TUBE
NO-HUB
STANDARD AWWA WEIGHT CAST WEIGHT CAST TYPE L SCHEDULE 40
CAST IRON
DUCTILE IRON IRON SOIL IRON SOIL
SCHEDULE 40 SOIL PIPE TYPE K SCHEDULE 80 SDR 35
PIPE PIPE
SCHEDULE 80 SDR 26
NOMINAL NOMINAL
STEEL (C & SS) IRON COPPER PVC
SIZE SIZE
1
⁄8 - - - - - - 0.405 - 1
⁄8
1
⁄4 0.540 - - - - 0.375 0.540 - 1
⁄4
3
/8 0.675 - - - - 0.500 0.675 - 3
/8
1
/2 0.840 - - - - 0.625 0.840 - 1
/2
3
/4 1.050 - - - - 0.875 1.050 - 3
/4
1 1.315 - - - - 1.125 1.315 - 1
11/4 1.660 - - - - 1.375 1.660 - 11/4
11/2 1.900 - - - 1.90 1.625 1.900 - 11/2
2 2.375 - 2.25 2.38 2.35 2.125 2.375 - 2
21/2 2.875 - - - - 2.625 2.875 - 21/2
3 3.500 3.96 3.25 3.50 3.35 3.125 3.500 - 3
31/2 4.000 - - - - 3.625 4.000 - 31/2
4 4.500 4.80 4.25 4.50 4.38 4.125 4.500 4.215 4
41⁄2 5.000 - - - - - - - 41⁄2
5 5.563 - 5.25 5.50 5.30 5.125 5.563 - 5
6 6.625 6.90 6.25 6.50 6.30 6.125 6.625 6.275 6
7 7.625 - - - - - 7.625 - 7
8 8.625 9.05 8.38 8.62 8.38 8.125 8.625 8.400 8
9 9.625 - - - - - 9.625 - 9
10 10.75 11.10 10.50 10.75 - - 10.750 10.500 10
11 11.75 - - - - - 11.750 - 11
12 12.75 13.20 12.50 12.75 - - 12.750 12.500 12
14 14.00 15.30 - - - - - - 14
15 - - 15.62 15.88 - - - 15.300 15
16 16.00 17.40 - - - - - - 16
18 18.00 19.50 - - - - - 18.701 18
20 20.00 21.60 - - - - - - 20
21 - - - - - - - 22.047 21
22 22.00 - - - - - - - 22
24 24.00 25.80 - - - - - 24.803 24
26 26.00 - - - - - - - 26
28 28.00 - - - - - - - 28
30 30.00 32.00 - - - - - - 30
32 32.00 - - - - - - - 32
34 34.00 - - - - - - - 34
36 36.00 38.30 - - - - - - 36
42 42.00 44.50 - - - - - - 42
48 48.00 50.80 - - - - - - 48
54 54.00 57.10 - - - - - - 54
Standards 1 2 3 4 5 6
Notes a
Standards:
1. ASTM A53
2. AWWA C108-70, Table 8.2
3. ASTM A74, Table 2
4. ASTM A74, Table 1
5. Cast Iron Soil Pipe Institute, Standard 301-72, Table 1
6. ASTM B88-82
Notes:
a. Stainless steel tubing outside diameter equals nominal diameter.
68
Maximum Spacing Between Pipe Supports
CARBON STEEL PIPE - ft. COPPER TUBE - ft. PVC PIPE - ft. CPVC PIPE - ft. STAINLESS STEEL PIPE - ft.
NOMINAL SIZE STANDARD WEIGHT TYPE L, DRAWN SCHEDULE 40 SCHEDULE 40 SCHEDULE 10S/10
OR
TUBE SIZE WATER SERVICE VAPOR SERVICE WATER SERVICE VAPOR SERVICE WATER SERVICE WATER SERVICE VAPOR SERVICE
≤ 650ºF ≤ 250ºF ≤ 100ºF ≤ 300ºF
1
⁄4 - - 5.0 5.0 3.5 3.5 -
3
⁄8 7.0 8.0 5.0 6.0 3.5 4.0 8.0
1
⁄2 7.0 8.0 5.0 6.0 4.0 4.5 8.0
3
⁄4 7.0 9.0 5.0 7.0 4.0 5.0 9.0
1 7.0 9.0 6.0 8.0 4.5 5.5 9.0
11⁄4 7.0 9.0 7.0 9.0 5.0 5.5 9.0
11⁄2 9.0 12.0 8.0 10.0 5.0 6.0 12.0
2 10.0 13.0 8.0 11.0 5.0 6.0 13.0
21⁄2 11.0 14.0 9.0 13.0 6.0 7.0 14.0
3 12.0 15.0 10.0 14.0 6.0 7.0 15.0
31⁄2 13.0 16.0 11.0 15.0 6.5 7.5 16.0
4 14.0 17.0 12.0 16.0 6.5 7.5 17.0
5 16.0 19.0 13.0 18.0 7.0 7.5 19.0
6 17.0 21.0 14.0 20.0 7.5 8.0 21.0
8 19.0 24.0 16.0 23.0 8.0 9.0 24.0
10 22.0 26.0 18.0 25.0 8.5 10.0 26.0
12 23.0 30.0 19.0 28.0 9.5 10.5 30.0
14 25.0 32.0 - - 10.0 11.0 32.0
16 27.0 35.0 - - 10.5 12.0 35.0
18 28.0 37.0 - - 11.0 12.5 37.0
20 30.0 39.0 - - 11.5 13.0 39.0
24 32.0 42.0 - - 12.5 14.0 42.0
30 33.0 44.0 - - - - 44.0
36 35.0 46.0 - - - - 46.0
42 38.0 50.0 - - - - 50.0
Note:
1. Per MSS SP-58, Table 4
Recommended Minimum Rod Diameter for Single Rigid Rod Hangers

PIPE SIZE 3
/8 /2
1 3
/4 1 11/4 11/2 2 21/2 3 31/2 4 5 6 8 10 12 14 16 18 20 24 30
REC. ROD SIZE /8
3 1
/2 /8
5
/4
3
/8
7
1 11/4
Notes:
1. Per MSS SP-58, Table 3
2. Rods may be reduced one size for double rod hangers.
Sheet Metal Thickness

SHEET GAUGE - ga. 24 22 20 18 16 14 12 10
THICKNESS 0.0276 0.0336 0.0396 0.0516 0.0635 0.0785 0.1084 0.1382
Note:
1. Sheet metal thickness based on galvanized steel.
69
Pipe Chart
/8” PIPE SIZE - 0.675” O.D.

3 1
/2” PIPE SIZE - 0.840” O.D.
SCHEDULE NO. 40 80 40 80 160
WALL DESIGNATION STD. XS STD. XS XXS
THICKNESS - IN. 0.091 0.126 0.109 0.147 0.188 0.294
PIPE - LBS./FT. 0.568 0.739 0.851 1.088 1.309 1.714
WATER - LBS./FT. 0.083 0.061 0.132 0.101 0.068 0.022
3
/4” PIPE SIZE - 1.050” O.D. 1” PIPE SIZE - 1.315” O.D.
SCHEDULE NO. 40 80 160 40 80 160
WALL DESIGNATION STD. XS XXS STD. XS XXS
THICKNESS - IN. 0.113 0.154 0.219 0.308 0.133 0.179 0.250 0.358
PIPE - LBS./FT. 1.131 1.474 1.944 2.441 1.68 2.17 2.84 3.66
WATER - LBS./FT. 0.231 0.187 0.128 0.064 0.37 0.31 0.23 0.12
11/4” PIPE SIZE - 1.660” O.D. 11/2” PIPE SIZE - 1.900” O.D.
SCHEDULE NO. 40 80 160 40 80 160
THICKNESS - IN. 0.140 0.191 0.25 0.382 0.145 0.200 0.281 0.400
PIPE - LBS./FT. 2.27 3.00 3.77 5.22 2.72 3.63 4.86 6.41
WATER - LBS./FT. 0.65 0.56 0.46 0.27 0.88 0.77 0.61 0.41
2” PIPE SIZE - 2.375” O.D. 21/2” PIPE SIZE - 2.875” O.D.

SCHEDULE NO. 40 80 160 40 80 160
THICKNESS - IN. 0.154 0.218 0.343 0.436 0.203 0.276 0.375 0.552
PIPE - LBS./FT. 3.65 5.02 7.44 9.03 5.79 7.66 10.01 13.7
WATER - LBS./FT. 1.46 1.28 0.97 0.77 2.08 1.84 1.54 1.07
3” PIPE SIZE - 3.500” O.D. 31/2” PIPE SIZE - 4.000” O.D.

SCHEDULE NO. 40 80 160 40 80
THICKNESS - IN. 0.216 0.300 0.438 0.600 0.226 0.318 0.636
PIPE - LBS./FT. 7.58 10.25 14.32 18.58 9.11 12.51 22.85
WATER - LBS./FT. 3.2 2.86 2.35 1.80 4.28 3.85 2.53
4” PIPE SIZE - 4.500” O.D. 5” PIPE SIZE - 5.563” O.D.

SCHEDULE NO. 40 80 160 40 80 160
THICKNESS - IN. 0.237 0.337 0.531 0.674 .258 0.375 0.625 0.750
PIPE - LBS./FT. 10.79 14.98 22.51 27.54 14.62 20.78 32.96 38.55
WATER - LBS./FT. 5.51 4.98 4.02 3.38 8.66 7.89 6.33 5.62
70
Pipe Chart

SCHEDULE NO. 40 80 160 20 40 80 160
THICKNESS - IN. 0.280 0.432 0.718 0.864 0.250 0.322 0.500 0.875 0.906
PIPE - LBS./FT. 18.97 28.57 45.3 53.2 22.36 28.55 43.4 72.4 74.7
WATER - LBS./FT. 12.51 11.29 9.2 8.2 22.48 21.69 19.8 16.1 15.8
SCHEDULE NO. 20 40 60 80 160 20 40 80 160
WALL DESIGNATION STD. XS STD. XS
THICKNESS - IN. 0.250 0.365 0.500 0.593 1.125 0.250 0.375 0.406 0.500 0.687 1.312
PIPE - LBS./FT. 28.04 40.5 54.7 64.3 115.7 33.38 49.6 53.5 65.4 88.5 160.3
WATER - LBS./FT. 35.77 34.1 32.3 31.1 24.6 51.10 49.0 48.5 47.0 44.0 34.9
14” PIPE SIZE - 14” O.D. 16” PIPE SIZE - 16” O.D.
SCHEDULE NO. 10 30 40 80 160 10 30 40 80 160
THICKNESS - IN. 0.250 0.375 0.438 0.500 0.750 1.406 0.250 0.375 0.500 0.843 1.593
PIPE - LBS./FT. 36.71 54.6 63.4 72.1 106.1 189.1 42.1 62.6 82.8 136.5 245.1
WATER - LBS./FT. 62.06 59.7 58.7 57.5 53.2 42.6 81.8 79.1 76.5 69.7 55.9
SCHEDULE NO. 10 40 80 160 10 20 30 40 80 160
THICKNESS - IN. 0.250 0.375 0.500 0.562 0.937 1.781 0.250 0.375 0.500 0.593 1.031 1.968
PIPE - LBS./FT. 47.4 70.6 93.5 104.8 170.8 308.5 52.7 78.6 104.1 122.9 208.9 379.0
WATER - LBS./FT. 104.3 101.2 98.4 97.0 88.5 71.0 129.5 126.0 122.8 120.4 109.4 87.9
SCHEDULE NO. 10 20 40 80 160 10 20
THICKNESS - IN. 0.250 0.375 0.500 0.687 1.218 2.343 0.312 0.375 0.500
PIPE - LBS./FT. 63.4 94.6 125.5 171.2 296.4 541.9 98.9 118.7 157.6
WATER - LBS./FT. 188.0 183.8 180.1 174.3 158.3 127 293.5 291.0 286.0
SCHEDULE NO. 10 20 40 20
THICKNESS - IN. 0.312 0.375 0.500 0.750 0.375 0.500
PIPE - LBS./FT. 119.1 142.7 189.6 282.4 166.7 221.6
WATER - LBS./FT. 425.9 422.6 416.6 405.1 578.7 571.7
71
Terms of Sale
AGREEMENTS: All agreements are subject to strikes, accidents or other causes beyond our control. Prices and
terms are not subject to verbal changes or other agreements unless approved in writing by the seller.
TAXES: The buyer is liable for any federal or state taxes imposed on the seller unless the buyer provides the
seller with a tax exemption certificate acceptable to the taxing authority.
WARRANTY: We guarantee our manufactured products for one year from date of shipment to the extent that we
will replace those having manufacturing defects when used for the purpose which we recommended. If goods
are defective, the amount of damage is the price of the defective goods only and no allowance will be made for
labor or expense of repairing defective goods or damage resulting from the same. We warrant the products we
sell of other manufacturers to the extent of the warranties of their respective maker.
RETURNS: Permission to return standard stocked merchandise must be obtained in writing. Credit may be
issued subject to the following:
1. Return freight charges must be prepaid.
2. All material must be in first-class condition and in box quantities upon arrival at our plant;
if not, repackaging and reconditioning costs will be deducted from the credit.
3. If material is in approved condition, credit will be allowed on the basis of the price charged less
a minimum restocking charge of 20% and less any out-bound freight allowed or paid by us.
4. Special, non-stocked and custom-made merchandise is NOT RETURNABLE.
5. Materials are NOT RETURNABLE after 30 days beyond date of invoice.
CLAIMS: No claims for shortages allowed unless made in writing within ten (10) days of receipt of goods. All
material sent out will be carefully counted and packed. Claims for goods damaged or lost in transit should be
made to the carrier as our responsibility ceases on delivery to the carrier.
TERMS AND DESIGN: National Pipe Hanger Corporation reserves the right to make specification changes with-
out notice. While every effort has been made to assure the accuracy of information contained in this catalog
at the time of publication, we cannot accept responsibility for inaccuracies resulting from undetected errors or
omissions.
WARNING: National Pipe Hanger’s products are designed and manufactured in accordance with industry codes
and standards and are intended for service and installation as illustrated or described herein. National shall not
be responsible for any losses or damages sustained by the buyer or any other person as a result of misapplica-
tion. Products used for unintended purposes could fail, resulting in property loss, injury or death.
National Pipe Hanger Corporation’s Terms of Sale supersede Buyer’s supplemental or conflicting terms and
conditions to which notice of objection is hereby given.
Copyright © 2019 National Pipe Hanger Corporation- All Rights Reserved

October 2019
72
NATIONAL
PIPE HANGER CORPORATION
CORPORATE HEADQUARTERS
200 CAMPUS DR
MOUNT HOLLY, NJ 08060
TEL: (609) 261-5353
FAX: (609) 261-3249
MARYLAND OFFICE
15850 COMMERCE CT, SUITE P
UPPER MARLBORO, MD 20774
TEL: (301) 568-8805
FAX: (301) 967-1456
E-MAIL: SALES@NATIONALPIPEHANGER.COM WEBSITE: WWW.NATIONALPIPEHANGER.COM
© 2019 National Pipe Hanger Corporation Printed in the U.S.A. Revision Date: 10/1/2019

Catalogo Soportes

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Catalogo Soportes

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catalogo Soportes

Uploaded by

Copyright:

Available Formats

OCTOBER 2019

PIPE HANGERS & SUPPORTS

MADE IN THE USA

Pictorial Table of Contents

Hold Down Strap for Offset Return

Adjustable Clevis Hanger,

Standard Steel Heavy Duty Two-Bolt Heavy Duty Double Bolt

Pictorial Table of Contents

Four-Bolt Socket Four-Bolt Socket

Adjustable Pipe Support w/ Pipe Saddle Support w/ Pipe Saddle Support w/

Adjustable Pipe Saddle Support

Pictorial Table of Contents

Top Beam Clamp Retaining Welding Beam Attachment

Malleable Beam Clamp Light Welded Steel

Medium Welded Steel Heavy Welded Steel Light Welded Steel

Pictorial Table of Contents

Nailing Sleeve Waterproof Sleeve Wood-Knocker Bang-It Vertigo

Spring Wing Toggle Spring Wing Toggle

FIG. 100 Split Ring Extension Hanger

SERVICE: For suspension of non-insulated, stationary piping and

FIG. 105 Hanger Flange

NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805

FIG. 110 Adjustable Swivel Ring Hanger

FIG. 136 Hold Down Strap

FIG. 155 Offset Return Line J-Hook

SERVICE: For general piping running next to a wall.

NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805

FIG. 165 U-Bolt

SERVICE: For support, anchor or guide of heavy loads.

NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805

FIG. 200 Adjustable Clevis Hanger

NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805

FIG. 200 Adjustable Clevis Hanger, PVC

FIG. 205 Flat Top Clevis Hanger

NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805

FIG. 210 Adjustable Clevis Hanger w/ Extended Bottom

SERVICE: For the suspension of insulated, stationary piping services.

FIG. 215 Adjustable Clevis Hanger for DI Pipe

NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805

FIG. 220 Clevis Hanger w/ Welded Shield

SERVICE: For vapor sealed lines.

FIG. 230 V-Bottom Adjustable Clevis Hanger

NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805

FIG. 235 V-Channel

FIG. 245 Roller Chair

SERVICE: For use on lines subject to horizontal movement.

NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805

FIG. 248 Pipe Roller Stand

SERVICE: For use on lines subject to horizontal movement.

36 53/4 20 12 9 253/4 15/8 1 17 12 147.00 12000

FIG. 249 Adjustable Pipe Roller Stand

SERVICE: For use on lines subject to horizontal movement.

NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805

FIG. 250 Adjustable Roller Hanger

FIG. 260 Adjustable Two-Rod Roller Hanger

SERVICE: For suspension of pipe where longitudinal movement due to

NJ (609) 261-5353 www.nationalpipehanger.com MD (301) 568-8805