Technical Data Sheet

Approved 684;11420 1 684 zinc ethyl silicate ^(ValidationDate) 1

Resist 86

Product description
This is a two component moisture curing inorganic zinc ethyl silicate coating. It is a fast curing, very high zinc
dust containing product. It conforms to the compositional requirements of SSPC paint 20, level 1, ISO 12944-5
and AS/NZS 3750.15 1994. It provides excellent corrosion protection as a single coat or as part of a complete
coating system. It is heat resistant up to 540 °C. To be used as primer in a coating system and as single coat
system in atmospheric environments. Suitable for properly prepared carbon steel substrates only. This product
complies with ASTM D520 type II zinc dust.

Typical use
Protective:
Suitable for structural steel and piping to be exposed to highly corrosive environments, C5I or C5M (ISO
12944-2). Recommended for offshore environments, refineries, power plants, bridges, buildings, mining
equipment and general structural steel. Specially designed as a primer in coating systems where extended
durability is required.
Other

Approvals and certificates

Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in
offshore environment, below 120 °C.
Tested by independent institute for static coefficient of friction.
Additional certificates and approvals may be available on request.

Colours
greenish grey, grey

Product data
Property Test/Standard Description
Solids by volume OCCA Monograph No. 4 67 ± 2 %
Gloss level (GU 60 °) ISO 2813 matt (0-35)
Flash point ISO 3679 Method 1 14 °C
Density calculated 2,63 kg/l
VOC-US/Hong Kong US EPA method 24 (tested) 455 g/l
VOC-EU IED (2010/75/EU) (calculated) 510 g/l
VOC-China GB/T 23985-2009 (ISO 11890-1) (tested) 467 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.

Date of issue: 28 April 2016 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Resist 86

Film thickness per coat

Typical recommended specification range

Dry film thickness 50 - 90 μm

Wet film thickness 75 - 135 μm
Theoretical spreading rate 13,4 - 7,4 m²/l

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Carbon steel Sa 2½ (ISO 8501-1) with a surface Sa 2½ (ISO 8501-1) with a surface
profile Fine to Medium G (ISO 8503-2) profile Fine to Medium G (ISO 8503-2)

Application
Application methods
The product can be applied by

Spray: Use air spray or airless spray.

Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness. In order to avoid settling of heavy zinc, continuous
mechanical stirring during application is recommended.

Product mixing ratio (by volume)

Resist 86 Comp A 8 part(s)

Jotun Zinc 100 Comp B 2,6 part(s)

Component A is a liquid and Component B is dry zinc dust. Component A must be well shaken before use. Pour
the zinc dust slowly into the liquid during mechanical mixing. Stir until lump free and pass through a 60 mesh
sieve.

Date of issue: 28 April 2016 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Resist 86

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 4 / Jotun Thinner No. 25

Thinning max.: 5 %

Jotun Thinner No. 4: for fast evaporation.

Jotun Thinner No. 25: for slow evaporation.

Guiding data for airless spray

Nozzle tip (inch/1000): 17-21

Pressure at nozzle (minimum): 100 bar/1400 psi

Drying and Curing time

Substrate temperature 5 °C 10 °C 23 °C 40 °C

Surface (touch) dry 1h 30 min 15 min 13 min

Walk-on-dry 1.5 h 45 min 30 min 25 min
Dry to over coat, minimum 18 h 13 h 4h 1.5 h
Dried/cured for service 18 h 13 h 4h 1.5 h

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

The given drying and curing times, as well as over coating intervals for inorganic zinc ethyl silicates are
measured at relative humidity (RH) 80 % during application and curing. An even higher RH will increase the
curing speed. The paint requires continuous RH above 50 % to cure.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

Pot life 8h

Date of issue: 28 April 2016 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Resist 86

Heat resistance
Temperature
Continuous Peak

Dry, atmospheric 400 °C 540 °C

This product can withstand a peak temperature of 540 °C (1000 °F) for a longer period as well. A continuous
temperature above 400 °C will however affect the long term performance of an inorganic zinc silicate coating.

Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Note that the coating will be resistant to various immersion temperatures depending on the specific chemical
and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If
used as part of a system, ensure all coatings in the system have similar heat resistance.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Subsequent coat: epoxy, silicone acrylic

Packaging (typical)
Volume Size of containers
(litres) (litres)

Resist 86 Comp A 8 10
Jotun Zinc 100 Comp B 2.6 20

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Resist 86 Comp A 6 month(s)
Jotun Zinc 100 Comp B 48 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Date of issue: 28 April 2016 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Resist 86

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 28 April 2016 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com