Psychometric Chart PDF
Psychometric Chart PDF
Psychometric Chart PDF
CHART
If any of the two factors are known, the remaining two can be ascertained
from the chart.
Other details, such as enthalpy, moisture content, specific volume, etc. can
also be found from the chart, once any two of the four factors mentioned
above are known.
Symbols
used
Dry bulb temperature
dbt
(°C or °F)
Wet bulb temperature
wbt
(°C or °F)
Dew point
dpt
temperature (°C or °F)
Relative humidity [%] rh
Specific volume [cu.
m/kg of dry air or cu. v
ft/lb of dry air]
Moisture content
[g/kg or gr/lb of dry w
air]
Enthalpy [kcal/kg or
h
kJ/kg or BTU/lb]
• Thus the enthalpy or total heat content of air can be marked corresponding
to the wet bulb temperatures.
• In the psychrometric chart the enthalpy scale is laid along with the markings
of wet bulb temperatures on the saturation (or 100% RH) curve.
• This gives the total heat content of air in Kcal / kg (BTU / lb) of dry air.
Specific Volume
• The weight of air has to be taken for calculation purposes.
• But in field work we deal with volume of air (handled by fans, cooled
and dehumidified by cooling coils, heated by heaters, etc.).
• The ratings of fans of cooling and heating coils, etc. are given in terms
of the volume of air handled (m3 or cubic feet).
• Therefore in the psychrometric chart specific volume lines are given to
find the volume of air per unit weight.The specific volume (or density)
of air changes with temperature.
• The specific volume lines start from the saturation curve and drop
down with a slight angle to the vertical lines.
• These are marked in m3/kg (cu. ft/lb) of dry air.
METHOD OF USING THE PSYCHROMETRIC CHART
Example 1 - Let us take air at 29.4°C (85°F) dry bulb temperature and 21.1°C (70°F) wet bulb temperature.
Once the dry bulb and wet bulb temperatures are known, from the chart we can find (1) the relative humidity, (2)
enthalpy, (3) moisture content, (4) dew point and (5) specific volume. For the sake of clarity in the
understanding and use of the chart, Fig. 2 is drawn showing only the lines and curves pertaining to the above
example. The lines representing the given data, i.e. 29.4°C (85°F) dry bulb and 21.1°C (70°F) wet bulb are
shown in continuous lines while the derived data are represented in broken lines and curves. The procedure to be
followed is as follows:
• Locate the 29.4°C (85°F) mark on the dry bulb scale. Go vertically up the 29.4°C (85°F) line to the point
where this line intersects the (sloping) 21.1 °C (70°F) wet bulb line. The intersecting point is marked O in the
figure for identification. This intersecting point is the only one in the chart at which both the conditions of
29.4°C (85°F) dry bulb and 21.1 °C (70°F) wet bulb exist.
• The point (0) falls between the 40 and 50% RH curves. Judging the distances between the 40 and 50% curves
and point '0' from the 50% curve, we can take the RH of the air as 48%.
• By extending the 21.1°C (70°F) wet bulb line to the enthalpy scale, the total heat content of the air can be
read as 18.94 kcal/kg or 79.11 kJ/kg (34.1 BTU/lb) or dry air.
• A horizontal line through the intersecting point 'O' to meet the saturation curve on the left and the specific
humidity scale on the right, we have the constant dew point/constant specific humidity line for the conditions
of our example. Where the horizontal line meets the saturated curve is the dew point of the air. This is
17.22°C (63°F) in our example. On the right end of the line we can read the moisture content or specific
humidity as 12.28 g/kg (86 gr./lb) of dry air.
• Since the 0.87 m3/kg (14 cu. ft/lb) specific volume line passes through the intersecting point (O) of the dry
and wet bulb lines of the air, the specific volume of the air is 0.87 m3/kg (14 cu. ft/lb) of dry air.
• Thus by knowing any two independent factors of the six factors, we can trace the other factors from the chart.
Sensible Heating (of Air) Only.
By sensible heating we mean
adding heat to air, which raises the
temperature of air.
No moisture is added and hence the
vapour content remains the same.
Thus the heat added only increases
the sensible heat of the air.
Since heat is added, the total heat
content of the air goes up.
Total heat content of air depends on
the WB temperature of air.
Since the total heat content of the
air goes up due to heating, its wet
bulb temperature also has to go up.
Cooling (Only)
The word 'only' in bracket above is used to
signify that the process is only sensible
cooling and there is no latent heat removal.
Latent heat removal from air occurs when
some moisture contained in the air is
condensed (i.e. its latent heat removed).
This brings down the amount of moisture
contained in the air.
This is possible only when the air is cooled
below its dew point, e.g. if some moisture is
to be removed from the air at 26.7°C (80oF)
DB and 18.3°C (65°F) WB the air will have
to be cooled below its dew point of 13.6°C
(56.5°F).
So when we say that air is only cooled,
without latent heat removal (or
dehumidification as it is called) the air is
cooled only to a temperature higher than its
dew point.
Cooling & Dehumidification
This process involves not only
sensible cooling but also latent
heat removal or reduction of
moisture content or
dehumidification.
Therefore the air will have to
be cooled below its dew point
temperature.
Thus air at 25.7°C (80°F) DB
21.1oC (70°F) WB will have
to be cooled below its dew
point of 18.6°C (65.5°F) to
obtain dehumidification.
Addition of Moisture
If by some method
moisture is injected
into the air sample
(without raising the
sensible heat of the
air), the process will be
represented by the
vertical line BC on the
chart as shown in Fig.
Heating &
Humidifying
If air is heated and
moisture is added to it,
the process is heating
and humidification.