MSDS Bentonita Pellets
MSDS Bentonita Pellets
MSDS Bentonita Pellets
Bentonite F2 Pellets
This generic SDS is provided by LKAB Minerals to give information to assist with material handling of the products listed which are
not classified as hazardous under the GHS and / or the CLP regulations.
1.2 Relevant identified uses of the substance or mixture and uses advised against
Identified uses: Borehole sealant
4.2 Most important symptoms and effects, both acute and delayed
Inhalation: No specific symptoms noted.
Ingestion: No specific symptoms noted.
Skin contact: No specific symptoms noted.
Eye contact: No specific symptoms noted.
4.3 Indication of any immediate medical attention and special treatment needed
Treat symptomatically
5.1 Extinguishing media This product is not flammable. Use fire extinguishing media appropriate for
surrounding materials.
6.2 Environmental precautions The product should not be dumped in nature but collected and delivered
according to agreement with the local authorities.
6.4 Reference to other sections For personal protection see section 8. For waste disposal see section 13.
Page 2 of 5
7.3 Specific 8:
SECTION endExposure
use(s) controls / personal The identified uses for this product are detailed in section 1.2
protection
8.1 Control parameters
Name STD TWA – 8hrs STEL – 15mins Notes
Bentonite WEL 10 mg/m3 4 mg/m3
Quartz WEL 0.1 mg/m3
Cristobalite WEL 0.1 mg/m3
WEL = Workplace Exposure Limit
Ingredient comments:
Dust contains respirable crystalline silica. Prolonged and/or massive inhalation of respirable crystalline silica dust may cause lung fibrosis,
commonly referred to as silicosis. Principal symptoms of silicosis are cough and breathlessness. Occupational exposure to respirable dust
should be monitored and controlled. The product should be handled using methods and techniques that minimise or eliminate dust
generation. The product contains less than 1% w/w RCS (respirable crystalline silica) as determined by the SWERF method. The respirable
crystalline silica content can be measured using the “Size-Weighted Respirable Fraction – SWERF” method. All details about the SWERF
method is available at www.crystallinesilica.eu
Engineering measures: Provide adequate ventilation. Observe occupational exposure limits and
minimise the risk of inhalation of dust.
Respiratory equipment: No specific recommendation made, but respiratory protection must be used if
the general level exceeds the recommended occupational exposure limit.
Wear dust masks in dusty areas.
Hand protection: No specific hand protection noted, but gloves may still be advisable.
Eye protection: Wear dust resistant safety goggles where this is a danger of eye contact.
Other protection: Provide eyewash station.
Hygiene measures: Wash hands at the end of each work shift and before eating, smoking and
using the toilet.
10.4 Conditions to avoid No specific conditions are likely to result in a hazardous situation
Acute toxicity
Acute toxicity (Oral LD50): Not relevant
Acute toxicity (Dermal LD50): Not relevant
Acute toxicity (Inhalation LC50): Not relevant
Eye contact: Particles in the eyes may cause irritation and smarting.
12.4 Mobility in soil: Not relevant, due to the form of the product.
12.5 Results of PBT and vPvB assessment: This product does not contain any PBT or vPvB substances.
13.1 Waste treatment methods: Dispose of waste and residues in accordance with local authority
requirements.
Page 4 of 5
SECTION 14: Transport considerations
Road transport notes: Not classified
Rail transport notes: Not classified
Sea transport notes: Not classified
Air transport notes: Not classified
14.1 UN Number: The product is not covered by international regulation on the transport of
dangerous goods (IMDG, IATA, ADR/RID).
14.7 Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
Not applicable
15.2 Chemical Safety Assessment: Not applicable. No chemical safety assessment has been carried out.
Disclaimer:
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any
process. Such information is, to the best of the company’s knowledge and belief, accurate and reliable as of the date indicated. However no warranty guarantee
or representation is made to its accuracy, reliability of completeness. It is the user’s responsibility to satisfy himself as to the suitability of such information for his
own particular use.
Page 5 of 5