Osciloscope AND Signal Conditioning

CHAPTER 3
OSCILOSCOPE
AND
SIGNAL
CONDITIONING
OUTLINE
Introduction to oscilloscope
Architecture of CRT
Measurement of Oscilloscope
Lissajous Pattern (LP) methods
INTRODUCTION TO OSCILLOSCOPE
 The CRO (Cathode Ray Oscilloscope), generally
referred to as the oscilloscope or simply “scope” is
probably the most versatile electrical measuring
instrument available
 Measurement of electrical parameters:
 AC or DC voltage
 AC or DC current
 Time
 Phase relationship
 Frequency
INTRODUCTION TO OSCILLOSCOPE
(CONT’D)
 Oscilloscope consists of the following parts:

 CRT – Cathode Ray Tube (Heart of Instrument)
 Vertical amplifier
 Horizontal amplifier
 Sweep generator
 Trigger circuit
 Associated power supplier
 There are 2 types of oscilloscope: analog and digital
 However its principle and basic characteristics still
the same
INTRODUCTION TO
OSCILLOSCOPE (CONT’D)
Analog Oscilloscope Digital Oscilloscope
BASIC CONSTRUCTION OF CRO
CATHODE RAY TUBE (CRT)
 CRT is the heart of the CRO providing visual display of
an input signal waveform
 A CRT contains four basic parts:
 An electron gun to provide steam of electrons

 Focusing and accelerating elements to produce a
well defined beam of electrons
 Horizontal and vertical deflecting plates to control
the path of the electron beam
 An evacuated glass envelope with a phosphorescent
screen which glows visibly when struck by electron
beam
CONT’D
CONT’D
CATHODE RAY TUBE (CRT) CONT’D
 CONTROL GRID
 Regulates the number of electrons that reach the
anode and hence control the brightness of the spot on
the screen.
 FOCUSING ANODE
 Ensures that the electrons leaving the cathode in
slightly different directions are focused down to a
narrow beam and all arrive at the same spot on the
screen.
CATHODE RAY TUBE (CRT) CONT’D
 ELECTRON GUN
 Consists of cathode, control grid, focusing anode and
accelerating anode.
 DEFLECTING PLATES
 An electric field between the first pair of plates
deflect the electrons horizontally and an electric field
between the second pair deflects them vertically. If no
deflecting fields are present, the electrons travel in a
straight line from the hole in the accelerating anode to
the center of the screen, where they produce a bright
spot.
PRINCIPLE ELEMENTS OF A CRT
•The interior of the tube is a very good vacuum, with a pressure of
around0.01 Pa (10−7 atm) or less.
1
•The cathode, at the left end in the figure, is raised to a high

temperature by the heater, and electrons evaporate from the surface of
2 the cathode.
•The accelerating anode, with a small hole at its center, is maintained at

a high positive potential V1, of the order of 1 to 20kV, relative to the
3 cathode.
•This potential difference gives rise to an electric field directed from

right to left in the region between the accelerating anode and the
4 cathode.
•Electrons passing through the hole in the anode form a narrow beam
and travel with constant horizontal velocity from the anode to the
5 fluorescent screen.
SIGNAL ON THE CRT
THE FRONT PANEL
MEASUREMENTS OF OSCILLOSCOPE
 Voltage Measurements
 Period and Frequency
Measurements
 Phase Measurements or
Time Delay
VOLTAGE MEASUREMENT
 The vertical scale is calibrated in either volts per division
or milivolts per division.
 Using the scale setting of the scope and the signal
measured off the face of the scope, then it can measured
peak-to-peak voltage for an ac signal
Vp-p = (vertical p-p division) x (volts/div)
OR
Vp-p = (no. of vertical division) x (volts/div)
VOLTAGE MEASUREMENT CONT’D
2.5 a) Voltage Peak-to-Peak

Vp-p= (V/Div) x No. of vert. div.
3.8 Vp-p Vp = 100 mV/div x (3.8 x 2)
= 0.76 V
T
3.8 b) Voltage Peak
TD
Vp = (V/Div) x No. of vert. div.
10 = 100 mV/div x (3.8)

A B
= 0.38 V
(Volt/Div : 100mV/Div, Time/Div : 0.5ms/Div)

PERIOD AND FREQUENCY
MEASUREMENT
 PERIOD
 Horizontal scale of the scope can be used to measure time in
second, milisecond or nanosecond.
 The interval of a pulse from start to end is the period of the
pulse.
Period = (horizontal p-p division) x (time/div)
 FREQUENCY
 The measurement of a repetitive waveform period can be
used to calculate the signal frequency.
F= 1/T
PERIOD AND FREQUENCY
MEASUREMENT CONT’D
2.5 a) Period, T
T = (Time/Div) x (no.
div/cycle)
3.8 Vp-p Vp
= 0.5ms/div x 10
T
= 5ms
3.8
TD
b) Frequency, f
f = 1/T
10
A B = 1/5ms
= 200 Hz
(Time/Div : 0.5ms/Div)
PHASE SHIFT (PHASE DIFFERENT)
 The time interval between pulses is called pulse delay.
 The pulse delay is measured between the midpoint at the
start of each pulse
Phase difference,Ө = (phase difference in division) x (degrees/div)

PHASE SHIFT (PHASE DIFFERENT)
CONT’D
2.5 1 cycle = 10 div

TD = 2 div
3.8 Vp-p Vp Therefore,
1 cycle : 10 div = 360o
T
3.8 1 div = 360o / 10 = 36o
TD
2 div = 2 x 36o = 72o
10
A B
(Time/Div : 0.5ms/Div)
LISSAJOUS PATTERNS
 FREQUENCY MEASUREMENT
 The alternative way of using oscilloscope to measure
frequency.
 In order to generate a Lissajous pattern a known reference
frequency sine wave is applied to one of the deflection plates
of the oscilloscope and the unknown sinusoidal signal to the
other deflection plates
 A Lissajous pattern is produced on the scren according to the
frequency ration between the two signal:
Fy = Number of positive peaks

Fx Number of right hand side peaks
LISSAJOUS PATTERNS CONT’D
 PHASE ANGLE MEASUREMENT
 Oscilloscope can be used in the X-Y mode to determine the
phase angle between two signals.
 This useful technique is limited to small frequency.
 The formula for phase angle measurement:
Sin θ = Y1/Y2 = X1/X2

Where θ = phase angle in degree
Y1 = the distance from X-axis to the point where the Lissajous
pattern crosses Y-axis
Y2 = the maximum vertical distance on the Lissajous
X1 = the distance from Y-axis to the point where the Lissajous
pattern crosses X-axis
Y2 = the maximum vertical distance on the Lissajous
θ- phase angle in degree Yo-Y axis intercept Ym-maximum vertical deflection

 EXAMPLE
If, in figure above, the distance Yo is 1.8cm and

Ym=2.3cm, what is the phase angle?
SOLUTION

Osciloscope AND Signal Conditioning

Uploaded by

Copyright:

Available Formats

Osciloscope AND Signal Conditioning

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Osciloscope AND Signal Conditioning

Uploaded by

Copyright:

Available Formats

CHAPTER 3

 Oscilloscope consists of the following parts:

 An electron gun to provide steam of electrons

•The cathode, at the left end in the figure, is raised to a high

•The accelerating anode, with a small hole at its center, is maintained at

•This potential difference gives rise to an electric field directed from

Vp-p = (vertical p-p division) x (volts/div)

2.5 a) Voltage Peak-to-Peak

10 = 100 mV/div x (3.8)

(Volt/Div : 100mV/Div, Time/Div : 0.5ms/Div)

Period = (horizontal p-p division) x (time/div)

Phase difference,Ө = (phase difference in division) x (degrees/div)

2.5 1 cycle = 10 div

Fy = Number of positive peaks

Sin θ = Y1/Y2 = X1/X2

θ- phase angle in degree Yo-Y axis intercept Ym-maximum vertical deflection

If, in figure above, the distance Yo is 1.8cm and

You might also like