Product Data Sheet
Hempadur
Multi-Strength 45753
Product characteristics VOC content mixed product
5% thinning, Limit value,
Legislation Value
Description by volume phase II (2010)ª
Hempadur Multi-Strength 45753 is a self-priming, high-build, pure
epoxy coating which cures to an abrasion and corrosion resistant 234 g/L 265 g/L 500 g/L
EU
coating. Applicable by standard heavy-duty airless spray equipment. [1.95 lb/US gal] [2.21 lb/US gal] [4.17 lb/US gal]
Complies with EU Directive 2004/42/EC, The Paints Directive on the 234 g/L
limitation of volatile organic compounds: subcategory j. US (coatings) - -
[1.95 lb/US gal]
Calculated according to specific legislation, see details in the Explanatory
Recommended use
Notes available at the Hempel website [Link] or at your local Hempel
Hempadur Multi-Strength 45753 is recommended as a heavy duty
website. VOC values may vary with shade, please consult the Safety Data
coating for areas exposed to abrasion and aggressive corrosive
Sheet, section 9. ªEU Directive 2004/42/CE.
climate such as ramps, ship hulls and holds of bulk carriers. The
product is also suitable for ballast tank coatings for special purposes
such as chemical carriers carrying hot cargoes and other purposes Handling
where a pure epoxy coating is requested. Is applicable as a finishing Handle with care. Before and during use, observe safety labels on
coat where a cosmetic appearance is of less importance. packaging and paint containers and follow all local and national safety
Hempadur Multi-Strength 45753 is intended for use in cold climates. regulations. Always consult Hempel’s Safety Data Sheet for this
product along with the Product Data Sheet.
Service temperature:
- Maximum, dry exposure only: 140°C [284°F]. For professional use only.
- Maximum, in water (no temperature gradient): 50°C [122°F].
- Other liquids: Please contact Hempel.
Certificates / Approvals Product data
- Recognized Abrasion Resistant Ice Coating. Consult Hempel for
specific Type Approval Certificates. Product code
- Meets requirements for internal use in pipelines for power 45753
generation when tested according to NS 5417 (Norwegian
standard).
Product components
Base 45755
Features Curing agent 98750
- High mechanical resistance.
- High surface tolerance.
Standard shade* / code
Grey 12340
Product safety Gloss
Semi-gloss
Flash point 27°C [81°F]
Volume solids
80 ± 2%
Specific gravity
1.6 kg/L [13 lb/US gal]
Reference dry film thickness
200 micron [7.9 mils]
* Other shades are available, please contact your local Hempel representative. Issued by Hempel A/S - August 2020
1/3
Product Data Sheet
Hempadur
Multi-Strength 45753
Surface preparation Application method
Thinning
Tool Application parameters
Cleanliness max vol.
- Remove oil, grease and other contaminants by suitable detergent
cleaning. Nozzle pressure: 250 bar [3600 psi]
Airless spray 5%
- Remove salts, detergents and other contaminants by high pressure Nozzle orifice: 0.021-0.023"
fresh water cleaning.
Thinning is usually not needed, consult the Specification. Spray data are
indicative and subject to adjustment. Pressure is for a material temperature of
New build: 20°C [68°F].
- Abrasive blasting to min. Sa 2½ (ISO 8501-1) / SP 10 (SSPC).
- Concrete: According to Specification
Film thickness
Repair: Specification range Low High
- Abrasive blasting to min. Sa 2 (ISO 8501-1) / SP 6 (SSPC).
- Water jetting to Wa 2½ (ISO 8501-4). 150 micron 310 micron
Wet film thickness
- Feather edges to sound surrounding coating. [6 mils] [12 mils]
- Flash rust degree of maximum FR M (ISO 8501-4). 125 micron 250 micron
Dry film thickness
[4.9 mils] [10 mils]
Roughness
6.4 m²/L 3.2 m²/L
- Surface profile Medium (G) (ISO 8503-2) / Rugotest No. 3 BN10a-b Theoretical spreading rate
[260 sq ft/US gal] [130 sq ft/US gal]
/ Rz 60-100 micron [2.4-4 mils].
Product may be specified in another film thickness than indicated depending
Consult Hempel's separate Surface Preparation Guidelines for more on purpose and area of use. This will alter spreading rate, drying and curing
details. time and overcoating interval. For best performance, avoid excessive film
thickness. Dry film thickness should not exceed 600 micron [24 mils] per coat.
Application conditions
Application - Temperature of product must be above 15°C [59°F] during
application.
- To avoid condensation, apply on a clean and dry surface with a
Mixing ratio temperature that is at least 3°C [5°F] above the dew point.
Base 45755 : Curing agent 98750 - Surface temperature must be above -10°C [14°F] during application
(3 : 1 by volume) and curing.
- Relative humidity must be below 85% during application and curing.
Thinner
Hempel's Thinner 08450
Cleaner Drying and overcoating
Hempel's Tool Cleaner 99610
Product compatibility
Pot life - Previous coat: None or according to specification.
- Subsequent coat: None or according to specification.
Product 15°C 20°C 25°C Recommended products are: Hempadur, Hempathane.
temperature [59°F] [68°F] [77°F]
Pot life 2 hours 1 hour ½ hours
Issued by Hempel A/S - August 2020
2/3
Product Data Sheet
Hempadur
Multi-Strength 45753
Drying time
Storage
Surface -10°C 0°C 20°C 30°C
temperature [14°F] [32°F] [68°F] [86°F] Shelf life
Touch dry hours 14 8 2½ 1½ Ambient 25°C 35°C
Surface dry hours 26 14 3½ 2 temperature [77°F] [95°F]
Hard dry hours 45 23 5 2½ Base 36 months 24 months
Fully cured days 63 32 7 3½ Curing agent 36 months 24 months
Overcoating with Min hours 45 23 5 4 Shelf life from date of production, when stored in original, unopened
same product Max days 90 90 30 22 containers. Thereafter, the product quality must be re-inspected. Always check
the best before date or expiry date on the label.
Determined for dry film thickness 200 micron [7.9 mils] at standard conditions,
see Hempel’s Explanatory Notes for details. The overcoating intervals have
Storage conditions
been determined at the conditions: atmospheric, severe. The intervals stated in
- Product must be stored according to local legislation, at maximum
the Specification supersede these values.
40°C [104°F], without direct sunlight and protected from rain and
snow.
Drying conditions
- To obtain the drying time stated, it is important to maintain sufficient
ventilation during application, drying and curing.
Overcoating details
Additional documents
- If the maximum overcoating interval is exceeded, roughening of the
surface is necessary to ensure intercoat adhesion. Additional information is available at the Hempel website [Link]
- Before overcoating, after exposure in contaminated environment, or at your local Hempel website:
clean surface thoroughly by high pressure fresh water hosing or by - Explanatory Notes explaining the fields in this Product Data Sheet.
hosing down with fresh water and scrubbing with a stiff brush and - Surface Preparation Guidelines.
allow to dry. - Application Guidelines for different application methods.
- Application Instruction for this product.
Other remarks
- The long maximum overcoating interval will be reduced if the
coating is more than just scarcely exposed to direct sunshine before
overcoating.
This Product Data Sheet (“PDS”) relates to the supplied product (“Product”) and is subject to updating from time-to-time. Accordingly, the buyer/applicator should have regard to the PDS supplied together
with the relevant batch of the Product (and not an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the following specifications, statements and/or guidelines as listed
below or as are available from the Hempel website under ‘Products’ at [Link] (the “Additional documents”):
No. Document description Location/comments
1. Technical Statement One-off specific advice provided on request for specific projects
2. Specification Only issued for specific projects
3. PDS This document
4. Explanatory Notes to the PDS Available at [Link] and contain relevant information about the Product testing parameters
5. Application Instruction Where available, at [Link]
6. Generic technical guidelines (e.g. on application and surface preparation) Where available, at [Link]
In the event of a conflict of information between the PDS and the Additional documents, the order of priority of information shall be in the order as set out above. In such event you should also contact your
representative at Hempel for clarification. Furthermore, the buyer/applicator must have full regard to the relevant Safety Data Sheet provided with each Product and which can also be downloaded from
[Link].
Hempel shall not be liable for defects where the application of the Product has not been made fully in accordance with the recommendations and requirements set out in the relevant PDS and the Additional
Documents. The information and terms of this disclaimer apply to this PDS, the Additional documents and any other documents supplied by Hempel in respect of the Product. In addition, the Product is
supplied and all technical assistance is given subject to Hempel’s General Conditions of Sale, Delivery and Service, unless otherwise expressly agreed in writing.
[Link] Issued by Hempel A/S - August 2020
3/3
