Lancnc-Maz: Supplemental Manual For The

Supplemental Manual for the
LANCNC-MAZ
FTP LAN network data server for Mazak CNC Controls
T-1, M-1, M Plus, T Plus, M-2, T-2, M32, T32, Fusion
2008-2014 Calmotion LLC, All rights reserved
Calmotion LLC
21720 Marilla St
Chatsworth, CA 91311
www.calmotion.com
Mazatrol T-1 or M-1
Figure 2: Data output options

Figure 1: Mazatrol T-1 Control
Figure 3: DATA IN and DATA OUT soft keys, INPUT hard key
and the display showing END indicating the completion of
DATA IN
Refer to the figures above when following the instructions to send or receive files from
the Mazatrol on a M-1 or T-1 control.
To Send CMT programs out to the LANCNC:
On the LANCNC unit:

1. Choose the CNC to File option on the LANCNC unit
2. Press the key under Start on the LANCNC unit (press DIR to choose a different
file name to save to).
On the Mazatrol:
2
©2008-2014 Calmotion LLC, all rights reserved
3. Press Menu Select on Mazatrol
4. Press soft key Data IN OUT on Mazatrol
5. Press soft key Data OUT on Mazatrol
6. The prompt “DATA OUT (INPUT)?” is displayed
7. Press the 1 key to send programs out to LANCNC
8. Press soft key Data OUT
9. Press the Input button
10. When it shows “END” on screen it is complete
On the LANCNC unit:
11. Select Done on the LANCNC unit
To receive CMT programs into the Mazatrol from LANCNC:
On the LANCNC unit:

1. Choose the File to CNC option on the LANCNC unit
2. Choose the file to be sent to the CNC
3. Press button under Start on the LANCNC unit
On the Mazatrol:
4. Press the key under Start on the LANCNC unit (press DIR to choose a different
file name to save to). Press Menu Select on Mazatrol
5. Press soft key Data IN OUT on Mazatrol
6. Press soft key Data IN on Mazatrol
7. Press the 1 key to receive programs into LANCNC
8. Press the Input button
On the LANCNC unit:
12. Select Done on the LANCNC unit
3
Mazatrol T-2, M-2, M Plus or M32
Figure 5: LANCNC on Mazatrol M Plus
Figure 4: Mazatrol M Plus
Figure 6: Save or Load programs on a Mazatrol M Plus Figure 7: Parameters on M Plus control
control
Figure 8: Input button the M Plus

control
4
Figure 9: Mazatrol will probably have two DB25
female connectors, the one labeled Cassette must be
used to save and load Mazatrol conversational
Figure 10: M-2 control screen programs. Sometimes the port is label with a picture
of a cassette tape. The other DB25 is used only for
EIA G code programs.
Refer to the figures above when following the instructions to send or receive files from
the Mazatrol on a M-2, T-2, M Plus, T Plus, M32 or T32 control.
To Send programs out to the LANCNC:
On the LANCNC unit:

1. Choose the CNC to File option on the LANCNC unit
2. Press the key under Start on the LANCNC unit
On the Mazatrol:
3. Press DATA I/O button on Mazatrol
4. Press soft key CMT I/O on Mazatrol
5. press SAVE NC->CMT button
6. Select Program File on Mazatrol to show existing programs in memory
7. Press the 1 key then Input key on the Mazatrol
8. Shows 1 on the NC side
9. Press soft key START on the Mazatrol
On the LANCNC unit:
10. Select Done
To receive programs into the Mazatrol from LANCNC:
On the LANCNC unit:

1. Choose the File to CNC option on the LANCNC unit
2. Choose the file to be sent to the CNC
3. Press button under Start on the LANCNC unit
On the Mazatrol:
4. Press DATA I/O button on Mazatrol
5
5. Press soft key CMT I/O on Mazatrol
6. Press soft key LOAD NC->CMT on Mazatrol
7. Enter program number(s) that are to be loaded on the CMT side of the screen
8. Press Start on the Mazatrol
9. If completed properly Mazatrol will show the program numbers on the NC side of
the screen as loaded.
On the LANCNC unit:
10. Select Done
For Mazak machines that use the CMT protocol, the parameters should be set to:
Baud Rate: 4800

Data/Parity/Stop: 8, N, 2
Flow Control: CMT16 (for M1 and T1 controls)
CMT Ver 1 (Typically for the older controls, if doesn't verify use Ver 2)
CMT Ver 2 (Typically for the newer controls, if doesn't verify use Ver 1)
End of Block Delay: No delay
End of Block Char: none/binary
Start of Tx: none
End of Tx: none
Start Rx: Automatic
6

Lancnc-Maz: Supplemental Manual For The

Uploaded by

Copyright:

Available Formats

Lancnc-Maz: Supplemental Manual For The

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lancnc-Maz: Supplemental Manual For The

Uploaded by

Copyright:

Available Formats

How do you send programs from the Mazatrol to the LANCNC unit?

How do you receive programs into the Mazatrol from the LANCNC unit?

Supplemental Manual for the

2008-2014 Calmotion LLC, All rights reserved

Figure 2: Data output options

To Send CMT programs out to the LANCNC:

On the LANCNC unit:

To receive CMT programs into the Mazatrol from LANCNC:

On the LANCNC unit:

Figure 5: LANCNC on Mazatrol M Plus

Figure 4: Mazatrol M Plus

Figure 8: Input button the M Plus

To Send programs out to the LANCNC:

On the LANCNC unit:

To receive programs into the Mazatrol from LANCNC:

On the LANCNC unit:

Baud Rate: 4800

You might also like