CDP & Telnet

6/16/2013
Ch.4 – Learning About Other

Devices (CDP and Telnet)
CCNA 1 version 3.0

Rick Graziani
Cabrillo College
Overview
Students completing this module should be able to:

• Enable and disable CDP
• Use the show cdp neighbors command
• Determine which neighboring devices are connected to
which local interfaces
• Gather network address information about neighboring
devices using CDP
• Establish a Telnet connection
• Verify a Telnet connection
• Disconnect from a Telnet session
• Suspend a Telnet session
• Perform alternative connectivity tests
• Troubleshoot remote terminal connections
1
6/16/2013
Introduction to CDP
• Cisco Discovery Protocol (CDP) is a Layer 2 protocol that connects

lower physical media and upper network layer protocols.
• CDP is used to obtain information about neighboring devices, such as:
– the types of devices connected
– the router interfaces they are connected to
– the interfaces used to make the connections
– the model numbers of the devices
• CDP is media and protocol independent, and runs on all Cisco
equipment over the Subnetwork Access Protocol (SNAP).
Information obtained with CDP
• CDP Version 2 (CDPv2) is the most recent release of the protocol.

Cisco IOS (Release 12.0(3)T or later) supports CDPv2.
• CDP Version 1 (CDPv1) is enabled by default with Cisco IOS (Release
10.3 to 12.0(3)T).
2
6/16/2013
Implementation, monitoring, and

maintenance of CDP
This router’s interface Remote router’s interface
• The cdp run command is used to enable CDP globally on the router.
• By default, CDP is globally enabled.
• The cdp enable command is used to enable CDP on a particular
interface.
• On Cisco IOS Release 10.3 or higher, CDP is enabled by default on all
supported interfaces to send and receive CDP information.
• CDP could be enabled on each of the devices interfaces by using the
cdp enable command.

maintenance of CDP
3
6/16/2013

maintenance of CDP

maintenance of CDP
4
6/16/2013

maintenance of CDP
Disabling CDP
To disable CDP on a specific interface after it

has been enabled, use the no CDP enable
command in interface configuration mode.
5
6/16/2013
Troubleshooting CDP
Getting Information about Remote Devices
• Establish a Telnet connection

• Verify a Telnet connection
• Disconnect from a Telnet session
• Suspend a Telnet session
• Perform alternative connectivity tests
• Troubleshoot remote terminal connections
6
6/16/2013
Telnet
• Telnet is a virtual terminal protocol that is part of the

TCP/IP protocol suite.
• It allows connections to be made to remote hosts.
Establishing and verifying a Telnet

connection
• To initiate a Telnet session any of the following alternatives can be

used:
Denver>connect paris
Denver>paris
Denver>131.108.100.152
Denver>telnet paris
• A hostname table or access to DNS for Telnet must be present for a
name to work.
• Otherwise, the IP address of the remote router must be entered.
7
6/16/2013
Establishing and verifying a Telnet

connection
RouterA#conf t
Enter configuration commands, one per line. End with CNTL/Z.
RouterA(config)#ip host RouterA 10.1.1.1
Does not have to be the router-name
RouterA(config)#exit
but it is generally a good idea.
RouterA#telnet routera Not case sensitive.
Trying RouterA (10.1.1.1)... Open
User Access Verification
Password:
RouterB>
• This is where the ip host commands can be helpful.
Telnet password – line vty

RouterA>telnet 10.1.1.1
Trying 10.1.1.1 ... Open
Password required, but none set
[Connection to 10.1.1.1 closed by foreign host]

RouterA>
RouterB(config)#line vty 0 4
Configure vty password RouterB(config-line)#login
on RouterB RouterB(config-line)#password cisco
Password:cisco Telnet works! Enter vty password

RouterB>
RouterB>exit Exit closes (ends) telnet session
RouterA>
• You must have the vty password set on the remote routers.
• We will always use vtypass as our vty passwords!
8
6/16/2013
Telnet and the privilege password

Password:cisco
RouterB>ena Cannot enter privilege mode because there is no privilege
% No password set password (enable secret). Can only enter this mode from
RouterB>exit the console until the password is created.
Configure vty password

RouterB(config)#enable secret cisco
on RouterB
Password:vtypass
RouterB>ena
Password:cisco
RouterB#exit
RouterA>
• If there is no privilege password on the remote router, you cannot

enter privilege mode!
Disconnecting and suspending Telnet

sessions
• A session is suspended for a limited time, to resume a Telnet session

that has been suspended, just press Enter.
• The command show sessions will show what Telnet sessions are
taking place.
9
6/16/2013
Disconnecting and suspending Telnet sessions

RouterA>connect
Host: 10.1.1.1
Or the “telnet” command
Password:vtypass
RouterB>
RouterB> <control-shift-6, x>
RouterA>show sessions
Conn Host Address Byte Idle Conn Name
* 1 10.1.1.1 10.1.1.1 0 0 10.1.1.1
RouterA> <enter>
[Resuming connection 1 to 10.1.1.1 ... ]
RouterB>exit

RouterA>show sessions
% No connections open
RouterA>
• If there is no privilege password on the remote router, you cannot enter

privilege mode!
Advanced Telnet operation
Multiple Telnet
sessions
Connection
ID
• If the resume command is used it requires a connection ID.

• The connection ID is shown by using the show sessions command.
10
6/16/2013
Alternative connectivity tests
• As an aid to diagnosing basic network connectivity, many

network protocols support an echo protocol.
• The ping target 172.16.1.5 in Figure responded
successfully to all five datagrams sent.
• The exclamation points (!) indicate each successful echo.
• If one or more periods (.) are received instead of
exclamations on the display, the application on the router
(or source device) timed out waiting for a given packet
echo from the ping target.
11
6/16/2013
• The traceroute command is the ideal tool for finding where data is
being sent in a network.
• If one of these routers is unreachable, three asterisks (*) will be
returned instead of the name of the router.
• The traceroute command will continue attempting to reach the next
step until the Ctrl-Shift-6 escape sequence is used.
Troubleshooting IP addressing issues
• ping uses the ICMP protocol to verify the hardware connection and
the IP address of the network layer. This is a basic testing mechanism.
• telnet verifies the application layer software between source and
destination. This is the most complete test mechanism available.
• traceroute allows the location of failures in the path from the source
to the destination. Trace uses Time to Live values to generate
messages from each router along the path.
12
6/16/2013
Summary
13

CDP & Telnet

Uploaded by

Copyright:

Available Formats

CDP & Telnet

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CDP & Telnet

Uploaded by

Copyright:

Available Formats

6/16/2013

Ch.4 – Learning About Other

CCNA 1 version 3.0

Students completing this module should be able to:

• Cisco Discovery Protocol (CDP) is a Layer 2 protocol that connects

Information obtained with CDP

• CDP Version 2 (CDPv2) is the most recent release of the protocol.

Implementation, monitoring, and

This router’s interface Remote router’s interface

Implementation, monitoring, and

Implementation, monitoring, and

Implementation, monitoring, and

Implementation, monitoring, and

To disable CDP on a specific interface after it

Getting Information about Remote Devices

• Establish a Telnet connection

• Telnet is a virtual terminal protocol that is part of the

Establishing and verifying a Telnet

• To initiate a Telnet session any of the following alternatives can be

Establishing and verifying a Telnet

User Access Verification

• This is where the ip host commands can be helpful.

Telnet password – line vty

Password required, but none set

[Connection to 10.1.1.1 closed by foreign host]

User Access Verification

Password:cisco Telnet works! Enter vty password

Telnet and the privilege password

User Access Verification

Configure vty password

User Access Verification

• If there is no privilege password on the remote router, you cannot

Disconnecting and suspending Telnet

• A session is suspended for a limited time, to resume a Telnet session

Disconnecting and suspending Telnet sessions

User Access Verification

[Connection to 10.1.1.1 closed by foreign host]

• If there is no privilege password on the remote router, you cannot enter

Advanced Telnet operation

• If the resume command is used it requires a connection ID.

Alternative connectivity tests

• As an aid to diagnosing basic network connectivity, many

Alternative connectivity tests

Alternative connectivity tests

Troubleshooting IP addressing issues

You might also like