N. Oil Pump Removal and Disassembly 4. Remove oil pump cover and rotor assembly.

1. Remove strainer cover.

5. Remove pressure relief valve: remove circlip,

washer, spring, and plunger.

6. Remove oil pump check valve: remove cir­

clip, plug, spring, and plunger.

2. Remove oil pump.

O. Crankcase Disassembly

3. Remove oil
oil pump driven gear. bolt. This bolt is located near the transmission
drive axle, as shown. This bolt must be located
before proceeding with crankcase disassembly.
 oosen each bolt ½ turn, starting with the
1. L 2. Remove shift fork guide bar circlip (E-clip).
unnumbered bolt. Continue by loosening the Remove guide bar.
highest numbered bolts first. The numbers of
the bolts are cast in the cases. Numbers 24~
15 are on the top case. Numbers 14-1 are on
the bottom case.

2. Remove all crankcase holding bolts. Use a soft

rubber hammer to carefully separate the
crankcases. The crankshaft and transmission
shafts should stay in the bottom crankcase.

, 1

3. Remove main axle assembly.

4. Remove circlip (E-clip) holding shift fork

guide two (2).

3. Remove crankshaft. Note location of special

main bearing ('A' bearing). This is a combina­
tion side thrust bearing and main bearing.

P. Transmission Disassembly

1. Remove middle driven gear.

5. Remove guide bar, washer and both shift forks.
6. Remove bolt holding middle drive gear t o
drive axle. Remove spacer.

9. Remove shift cam detent and shaft cam se­

7. Loosen transmission bearing cap nuts ½ turn.
curing bolt.
Remove nuts and cap.

10. Remove circlip on shift cam stopper plate.

Remove stopper plate and shift cam.
8. Remove middle drive gear. Push drive axle up
a t the bearing and out so that the middle drive
gear can be removed. Remove drive axle.

11. Further disassembly of the transmission shafts

can be undertaken after study of the transmis­
sion illustration.
1 AXLE, main (13T)
15 WASHER, plate (30.2-40-2.0)
30 WASHER, spring

2 GEAR, 4th pinion (21T)

16 CIRCLIP
31 BOLT, hexagon socket head

3 CIRCLIP
17 G E A R 4th wheel (23T)
32 MIDDLE DRIVEN GEAR

4 WASHER, gear hold 5

18 SHIM
COMP. (34T)

(25.2-30-1 .O)
19 GEAR, 3rd wheel (26T)
33 COLLAR (35-40-16)

5 GEAR, 3rd pinion (20T)

20 GEAR, 5th wheel (22T)
34 BEARING (B6207 special)

6 GEAR, 5th pinion (23T)

21 GEAR, 2nd wheel (27T)
35 PLUG

7 CIRCLIP (S-25)
22 CIRCLIP (S-30)
36 CIRCLIP

8 GEAR, 2nd pinion (17T)

23 SHIM, drive axle (24.2-33-1.6)
37 OIL SEAL (SW-48.8-72-9)

9 SHIM, drive axle

24 BEARING
38 NUT, hexagon

10 BEAR ING
25 WASHER, plate (30.2-40-2.0)
39 WASHER, plate

11 BEARING (B5205 special)

26 BEARING (B5206 special)
40 CAM, driven

12 CIRCLIP
27 CI RCLlP
41 CAM, drive

13 AXLE, drive
28 GEAR, middle drive (32T)
42 BEARING

14 GEAR, 1st wheel (32T)

29 WASHER, plate
43 SPRING, compression

 29

1 CAM, shift 11 SPRING, compression 21 B A R , shift fork guide 2

2 PIN, dowel (4-8) 12 GASKET, drain plug 22 FORK, shift 1
3 PIN, dowel (4-17.8) 13 SCREW 23 SHAFT, shift lever
4 BEARING 14 BOLT 24 SCREW, flat head
5 C l R C L l P ( 3 4 ø special) 15 WASHER, lock 25 LEVER, shift 2
6 PLATE, side 16 B A R , shift fork guide 1 26 C l R C L l P (E-9)
7 SCREW, flat head 17 F O R K , shift 2 27 SPRING, torsion
8 P L A T E , stopper 18 PIN, cam follower 28 LEVER, shift 3
9 C l R C L l P ( S -30) 19 WASHER, plate (12-22-1.0) 29 C l R C L l P (E-7)
10 STOPPER, cam 20 C l R C L l P (E-10)
3-3 INSPECTION AND REPAIR

A. Cylinder Head Cover Intake . 020-.041mm 0.10 mm

(.0008~.0016") (.004")
Place head cover on a surface plate. There should be
no warpage. Correct b y re-surfacing as follows: Exhaust . 035-.059mm 0.12mm
(.0014~.0023") (.005")
Place #400 or #600 grit wet sandpaper on surface
plate and re-surface head cover using a figure-eight 2. Valve stem end
sanding pattern. Rotate head cover several times to
avoid removing too much material from one side. Inspect end o f valve stem. I f the end appears
t o be "mushroomed" or has a larger diameter
than the rest of the stem, the valve, valve
B. Cylinder Head guide, and oil seal should be replaced.

1. Remove spark plugs.

2. Remove valves.

3. Using a rounded scraper, remove carbon de-

posits from combustion chamber. Take care
to avoid damaging spark plug threadsand valve
seats. Do n o t use a sharp instrument. Avoid
scratching the aluminum.
3. Turn valve on a "V" block and measure the
4. Place on a surface plate. There should be no amount o f stem runout with a dial gauge. If
warpage. Correct b y re-surfacing as follows: it exceeds the maximum limit, replace the
valve.
Place #400 or #600 grit wet sandpaper o n sur­
face plate and re-surface head using a figure- Maximum Valve Stem Runout:
eight sanding pattern. Rotate head several .03mm (.0012")
times t o avoid removing too much material
from one side. 4. Valve guide and valve oil seal replacement

C. Valve, Valve Guide and Valve Seat I f oil leaks into the cylinder through a valve
due to a worn valve guide, or i f a valve is re-
1. Valve stem wear must be measured and then placed, the valve guide should also be replaced.
combined with valve guide measurements t o
guide clearance. This clearance must be within NOTE: The valve oil seal should be replaced
tolerances. If it exceeds the maximum limit, whenever a valve i s removed or replaced.
then replace either or both valve and guide, as
necessary . a. Measure valve guide inside diameter with a
small bore gauge. I f it exceeds the limit, re-
place with an oversize valve guide.

I Guide diameter (I.D.): 7.01-7.02mm 7.10mm

(.276-.277") (0.280') I
b. To ease guide removal and reinstallation, and
t o maintain the correct interference fit, heat
the head to 100°C (212°F). Use an oven to
avoid any possibility o f head warpage due t o
uneven heating.

c. Use the appropriate shouldered punch (special

tool) t o drive the old guide out and drive the
new guide in.

NOTE: When a valve guide is replaced, the

o-ring should also be replaced.
 d. After installing the valve guide, use 7mm pits still exist, then continue to c u t w i t h the
reamer (special tool) t o obtain the proper valve 45° cutter. Remove just enough material t o
clearance. achieve a satisfactory seat.

e. After fitting the valve guide into the cylinder Standard Width Wear Limit
head, be sure to grind the valve seat, and per-
form valve lapping. The valve must be replaced Seat width 1.3mm 2.0mm
with a new one. (.050") (.080)

5. Grinding the valve seat c. I f the valve seat is uniform around the perim­
eter of the valve face, b u t i s too wide or not
a. The valve seat is subject to severe wear similar centered on the valve face, it must be altered.
t o valve face. Whenever the valve face is re- Use either the " FLAT" , 45°or 30°cutters
surfaced, the valve seat should also be re-sur t o correct the improper seat location in the
faced at a 45° angle. I n addition, i f a new valve manner described below:
guide has been installed (without any valve re-
pair), the valve seat should be checked to 1) If the valve face shows that the valve seat is
guarantee complete sealing between the valve centered on the valve face, but t o o wide,
face and seat. then lightly use both the " FLAT" and the
30° cutters t o reduce the seat width to
1.3mm (.05").

2) If the seat shows to be in the middle o f t h e

valve face, but too narrow, use the 45°
cutter until the width equals 1.3mm (.05").

3) If the seat is too narrow and right up near

the valve margin, then first use t h e " F L A T "
cutter and then the 45° cutter to get the
correct seat width.

4) If the seat is too narrow and down near the

bottom edge o f the valve face, then first use
the 30° cutter and then the 45° cutter.
CAUTION: I f the valve seat is obviously
pitted or worn, it should be cleaned w i t h a
valve seat cutter. Use the 45° cutter, and when
twisting the cutter, keep an even downward
pressure to prevent chatter marks.

If cutting section " A ' o f the intake valve seat,

use " F L A T " cutter (radius cutter). If cutting
section "A" o f the exhaust valve seat, use
" F L A T " cutter (also: radiused). If cutting sec­
tion "B", use the 45°cutter.

b. Measure valve seat width. Apply mechanic's

bluing dye (such as Dykem) to the valve face,
apply a very small amount of fine grinding
compound around the surface o f the valve
seat, insert the valve into position, and spin the
valve quickly back and forth. Lift the valve,
clean o f f all grinding compound, and check I
valve seat width. The valve seat will have re-
moved the bluing wherever it contacted the 6. Lapping the valve/valve seat assembly
valve face. Measure the seat width w i t h vernier
calipers. It should measure approximately a. The valve/valve seat assembly should be lapped
1.3mm (.05"). Also, the seat should be uniform if (1) neither the seat nor the valve face are
in contact area. If valve seat width varies, or if severely worn, or (2) if the valve face and valve
 seat have been re-surfaced and now require a measure spring free length. I f the free length
final light grinding operation for perfect seal­ of any spring has decreased more than 2mm
ing. (.080") from i t s specification, replace it.
b. Apply a small amount of coarse lapping com­
pound t o valve face. Insert the valve into the
head. Rotate the va!ve until thevalveandvalve
seat are evenly polished. Clean off the coarse
compound, then follow the same procedure
with fine compound,

Continue lapping until the valve face shows a

complete and smooth surface all the way
around. Clean off the compound material.
Apply bluing dye to the valve face and rotate
the valve face for full seat contact which is
indicated by a shiny surface all around the
valve face where the bluing has been rubbed c. Another symptom of a fatigued spring is in-
away. sufficient spring pressure when compressed.
This can be checked using a valve spring com­
c. Valve leakage check pression rate gauge. Test each spring indivi­
dually. Place it in the gauge and compress the
After all work has been performed on the spring first t o the specified compressed length
valve and valve seat, and all head parts have with the valve closed (all spring specifications
been assembled, check for proper valve/valve can be found in the previous section, Valve
seat sealing by pouring solvent into each of Spring), then t o the length with the valve
the intake ports, then the exhaust ports. There open. Note the poundage indicated on the
should be no leakage past the seat. I f fluid scale a t each setting. Use this procedure with
leaks, disassemble and continue t o lap with the outer springs, then the inner springs.
fine lapping compound. Clean all parts thor­
oughly, reassemble and check again with
solvent. Repeat this procedure as often as NOTE: All valve springs must be installed with
necessary t o obtain a satisfactory seal. greater pitch upward as shown.

D. Valve Spring and Lifters

1. Checking the valve springs

a. This engine uses two springs of different sizes

t o prevent valve float or surging. The chart 0OAO-
below shows the basic value characteristics.

b. Even though the spring is constructed of dur­

able spring steel, it gradually loses some of it's
tension. This is evidenced by a gradual short­
ening of free length. Use a vernier caliper t o

OUTER INNER
Free length 39.9mm (1.571") 35.6mm (1.402")
Installed length (valve closed) 34.5mm (1.358") 31.5mm (1.240")
Installed pressure 16.27~18.73 kg (35.9~41.3 Ib) 6.75~8.25 kg (14.9~18.2 Ib)
Compressed length (valve open) 26.0mm (1.024") 23.0mm (.908")
Compressed pressure 49.29~56.71 kg (108.7~125 Ib) 25.57~29.43 kg. (56.4~64.9 Ib)
Allowable tilt from vertical 1.6mm (.063") or 2.5°
 2. Valve lifter

a. Check each valve lifter for scratches or other

I PLASTIGAUGE I
damage. I f the lifter is damaged in any way,
the cylinder head surface in which it rides is
probably also damaged. I f the damage is severe,
it may be necessary to replace both the lifter
and the cylinder head.

CAMSHAFT
CYLINDER HEAD STUDS
FOR CAMSHAFT CAP

Cap Nut Tightening Torque:

0.8~1.0 m-kg (5.8~7.2 ft-lbs)

NOTE: Do not turn camshaft when measuring

clearance with Plastigauge.

NOTE: For proper valve lifter-to-head clear­ Camshaft-to-cap Clearance:

ance, always install lifters on their original
Standard: .020~.054mm (.0008~.0021")
valves.
Maximum: 0.160mm (.006")

E. Camshafts, Cam Chain and Cam Sprockets

If camshaft-to-cap clearance exceeds specifica­
tion, measure camshaft bearing surface diam­
1. Camshaft
eter.
a. The cam lobe metal surface may have a blue
discoloration due t o excessive friction. The Bearing Surface Diameter:
metal surface could also start t o flake off or Standard:24.97~24.98mm (0.9830~0.9835")
become pitted.

NOTE: The exhaust cam appears darker than

the intake cam. This is due to a special hard­ 1) I f camshaft diameter is less than specifica­
ening process and is not due to excessive tion, causing excessive clearance, replace
enaine heat. camshaft.

2) If camshaft is within specification and cam-

b. I f any of the above wear conditions are readily shaft-to-cap clearance is excessive, replace
visible, the camshaft should be replaced. cylinder head.
c. Even though the cam lobe surface appears t o 2. Cam Chain
be in satisfactory condition, the lobes should
be measured with a micrometer. Cam lobe Except in cases of oil starvation, the cam chain
wear can occur without scarring the surface. wears very little. If the cam chain has stretched
I f this wear exceeds a pre-determined amount, excessively and it is difficult t o keep the pro-
valve timing and lift are affected. Replace the per cam chain tension, the chain should be
camshaft if wear exceeds the limits. replaced.
d. Install the camshaft on the cylinder head.
Place a strip of Plastigauge between camshaft 3. Cam Sprockets
and camshaft cap as illustrated (lengthwise
along camshaft). Tighten the nuts with Check cam sprockets for obvious wear. Ex­
specified torque. Remove the camshaft cap amine damping rubber on sides of cam
and determine the clearance by measuring sprockets. If the damping rubber is disintegrat­
the width of the flattened Plastigauge. ing, the sprocket should be replaced. Damaged
 or disintegrating damping rubber will contam­ Cylinder wear should be measured a t three
inate the engine oil and will lead to excessive depths with a cylinder bore gauge. (See illu­
engine noise. stration.)

Standard Wear Limit

4. Cam Chain Dampers
Cylinder bore 68.00~68.02mm 68.10mm
Inspect the top cam chain damper (stopper (2.677~2.678 in.) (2.681 in.)
guide) and two (2) vertical (slipper-type) Cylinder taper ........ 0.05mm
dampers for excessive wear. Any that shows (0.002 in.)
excessive wear should be replaced. Worn
Cylinder 0.05mm
dampers may indicate an improperly adjusted
out-of-round ........ (0.002 in.)
or worn-out cam chain.

If the cylinder wall is worn more than wear limit, it

should be rebored.

G. Piston And Piston Rings

1. Piston

a. Measure the outside diameter of the piston a t

the piston skirt.

Measurement should be made a t a point l0mm

(.4 in.) above the bottom edge of the piston.
Place the micrometer a t right angles t o the
piston pin.

F. Cylinder

1. Inspect the cylinder walls for scratches. I f

vertical scratches are evident, the cylinder
wall should be rebored or the cylinder should
be replaced.

2. Measure cylinder wall wear as shown. I f wear

is excessive, compression pressure will de-
crease. Rebore the cylinder wall and replace
the piston and piston rings.
 The color mark is painted on the expander
spacer.
Standard 67.96mm
67.97m m Size Color
Oversize 1 68.25mm Oversize 1 Brown
Oversize 2 68.50mm Oversize 2
Oversize 3 68.75mm Oversize 3 Black
Oversize 4 Yellow

c. Push the ring into the bore and check end gap
clearance with a feeler gauge.
b. Determine piston clearance as follows:
NOTE: The end gap on the expander spacer
of the oil control ring is unmeasureable. I f the

I
Minimum bore measurement
oil control ring rails show excessive gap, all
- Maximum Diston measurement three components should be replaced.
= Piston clearance

Top/2nd ring 0.2~0.4mm 0.80mm

EXAMPLE: (.008~.016 in.) (0.03 in.)
Oil control 0.2~0.9mm Visual
68.02mm (Rails)
- 67.97mm
= .05mm piston clearance
H. Piston Pin

1. Apply a light film of oil t o pin. Install in con­

c. Piston ring/ring groove fit must have correct necting rod small end. Check for play. There
clearance. If the piston and ring have already should be no noticeable vertical play. If play
been used, the ring must be removed and the exists, check connecting rod small end for
ring groove cleaned of carbon. The ring should wear. Replace pin and connecting rod as re­
then be reinstalled. Use a feeler gauge to meas- quired.
ure the gap between the ring and the land.

Side clearance
11;: 0.04-0.08mm
(0.0016-0.003 in.)
0.03-0.07mm
(0.0012-0.0028 in .)
I 2. The piston pin should have no noticeable free
play in piston. If the piston pin is loose, re-
place the pin andlor the piston.

1. I. Crankshaft

1. Crankshaft Run-Out

Support the crankshaft a t both ends on

V-blocks. Measure the amount of crankshaft
2. Piston Ring run-out on the main bearing journals with a
dial gauge while rotating crankshaft.
a. The oversize top and middle ring sizes are
stamped on top of the ring.

Oversize 2 0.50mm
Oversize 3 0.75mm
Oversize 4 1.00mm

b. The expander spacer of the bottom ring (oil

control ring) is color-coded t o identify sizes.
I Run-out limit: .03mm (.001 in.) I
If run-out exceeds limit, replace crank.

2. Inspection Of Inserts
LEFT CENTER
Check the bearing inserts. If the inner orouter
surface is burned, flaked, rough, scratched or
worn, the insert should be replaced.

3. Measuring Main Bearing Oil Clearance

a. Clean all crankshaft and crankcase journal
surfaces.
b. Each main bearing journal is numbered 1, 2
b. Place upper crankcase half upside-down on a
or 3. Each crankcase bearing housing is num­
bench. Install bearing inserts into top crank-
bered 4, 5 or 6. The proper insert selection is
case.
made by subtracting the crankcase number
from the crankshaft journal number. The
c. Install crankshaft into upper crankcase.
result is the insert size (number).
d. Place Plastigauge on crankshaft journal surface
t o be inspected.

NOTE: Do not move crankshaft until clear­

ance check has been completed.

e. Install bearings inserts into bottom crankcase.

Carefully, place lower crankcase onto upper
crankcase.

f. Install crankcase holding bolts 1 through 10.

Tighten t o full torque in torque sequence
cast on crankcase.
g. Remove bolts in reverse assembly order I TOP CRANKCASE
(10,9,8.. . . .etc.)
Use the color code table t o choose the pro-
h. Carefully remove lower crankcase. Measure per insert.
width of Plastigauge on crankshaft journals t o
determine clearance. INSERT COLOR CODE
~

No. 1 Blue
Main bearing oil clearance: No. 2 Black
.022~.044mm No. 3 Brown
(.0008~.0017 in.) No. 4 Green
No. 5 Yellow

4. Crankshaft Main Bearing Selection

EXAMPLE:
a. Numbers used to indicate crankshaft journal Case No. (Minus) Journal No. = Insert No.
sizes are stamped on the L.H. crank web. The
first four (4) are main bearingjournal numbers,
starting with the left journal and proceding t o 4 - 2 = 2
left center, right center, and right. The three
(3) rod bearing journal numbers follow in No. 2 insert is Black. U s e a black main bearing
the same sequence. insert.
 c. Remove connecting rod and cap. Measure
NOTE: There is a special thrust bearing
width of Plastigauget o determine oil clearance.
(insert) located in the No. 3 main bearing
housing in the upper crankcase. The function
of this insert is t o provide a bearing surface I Oil clearance (rod): I
for crankshaft side thrust.
I .032~.054mm (.001~.002 in.)
I
c. When assembling, apply a liberal coat of
motor oil t o all bearing surfaces. d. Remove Plastigauge from bearing surfaces.

d. Observe normal crankcase holding bolt 4. Selecting Rod Bearing Inserts

torque sequence.
a. Connecting rod size numbers are indicated by
J. Connecting Rod 4. 5 or 6 and are marked in ink on the con­
necting rods and caps.
1. Remove rod cap securing nuts, rod cap and
inserts.

2. Inspection

a. Examine bearing inserts for scratches, flaking

or other obvious signs of wear or damage. If
the inner or outer surfaces are worn or dam-
aged, the inserts should be replaced.

b. Examine the connecting rods and crankshaft.

3. Measure Rod Bearing Clearance

Measurement o f rod bearing clearance is

b. The rod bearing journal size numbers are indi­
similar to main bearingclearance measurement.
cated by 1, 2 or 3 and are stamped on the left
end of the crankshaft,
a. Clean all bearing surfaces.

b. Place a piece of Plastigauge on connecting rod

cap. Place cap on crankshaft journal. Do not
allow the cap t o move. Install special bolts and
apply molybdenum disulfide grease t o the
threads. Install rod cap and nuts. Tighten rod
caps evenly t o specified torque:

c. The proper insert selection is made by sub­

tracting the rod size number from the crank-
shaft journal number. Use the color code t o
choose the proper insert.

Rod No. (Minus) Journal No. = Insert No.

5 - 2 = 3

Rod cap torque: 3.8 kg-m (27 ft-lbs) No. 3 insert is Brown. Use brown bearing inserts.
 EXAMPLE: a conventional motorcycle drive chain. The
plates of the chain form a mating surface for
INSERT COLOR CODE the primary gear teeth. That is, the primary
gears actually mesh with the chain plates. This
No. 1 Blue chain is extremely durable and, under normal
No. 2 Black conditions, can be expected t o last the life
of the motorcycle engine. However, if obvious
No. 3 Brown damage is caused through serious oil starva­
No. 4 Green tion or abrasive oil contamination, the chain
No. 5 Yellow should be replaced.

2. Clutch Damper
d. When assembling, apply a liberal coat of motor
oil t o all bearing surfaces. a Remove circlip using a press and special tool.
Press tool on collar no more than necessary t o
NOTE: When applying final torque to the rod remove circlip. Damper springs may be dam-
caos. Observe the following procedures: aged if excessive pressure is applied.

Apply molybdenum disulfide grease t o con­ b. Inspect damper cam and pin surfaces. Check
necting rod bolt threads. Apply torque evenly for smooth cam action (as illustrated by
to both ends of the cap. While tightening, if arrows). Check for excessive wear on cam and
a torque of 3.3 m-kg (24 ft-lbs) or more is pin surfaces. If operation is not smooth or cam
reached, DO NOT STOP tightening until surfaces are severely worn, replace damper
final torque is reached. If tightening is inter­ assembly.
rupted between 3.3 m-kg and 3.8 m-kg,
loosen the nut t o less than 3.3 m-kg and start
again. Tighten t o full torque specification
without pausing.

K. OIL PUMP

1. Check the clearance between housing and

outer rotor.

Standard clearance:
0.09~0.015mm
(0.0035~0.0059 in.)

2. Check the clearance between outer rotor and

inner rotor.
c. Inspect plate washer and thrust bearing for
Standard clearance: wear or damage. Replace as necessary.
0.03~0.09mm
(0.0011~0.0035 in.)

emove the relief valve and check valve plung­

3. R
ers from oil pump assembly. Check the
plungers for scratches and wear.

L. PRIMARY DRIVE

1. "Hy-Vo" Chain And Primary Gears

The "Hy-Vo" primary chain is a plate-and-pin

type that does not use rollers as in the case of